AZ1500/00

12/13/01 9:55

Page 1

CD Soundmachine

English

ACCESSORIES 1 x AC mains lead 1 x Remote Control (for AZ1505 model only) TOP AND FRONT PANEL (See 1) 1 VOLUME 3 , 4 - to adjust volume level. 2 DBB (Dynamic Bass Boost) - activates a more vivid bass response. 3 POWER slider - selects TAPE/ RADIO / CD function and also the power off switch (TAPE/ OFF). 4 BAND - selects waveband. 5 0-9: - digit panel CD: - track selection and direct playback; RADIO: - selecting a preset station. 6 PROGRAM CD: - programs tracks and reviews the program; Tuner: - programs preset radio stations. 7 SEARCH , CD: - searches backward and forward within a track; - skips to the beginning of a current track/ previous/ later track. RADIO: - (down, up) tunes to radio stations. 8 MODE - selects different play modes: e.g. REPEAT or SHUFFLE (random) order. 9 2; - starts or pauses CD playback. - to stop playback; - erases a CD program. ! Display - shows the status of the set. @ LIFT TO OPEN - lift here to open CD-tape door. # REMOTE SENSOR - (for AZ1505 model only) infrared sensor for remote control. $ CASSETTE RECORDER keys: RECORD 0 - to start recording. PLAY 2 - to start playback. SEARCH 5 / 6 - fast rewinds/ winds tape. STOP 9 - stops tape. PAUSE ; - pauses playback or recording.

CONTROL/POWER SUPPLY

BACK PANEL % Telescopic aerial - improves FM reception. ^ p - 3.5 mm stereo headphone socket. Note: The speakers will be muted when headphones are connected to the set. & AC MAINS - inlet for mains lead. * Battery compartment - for 6 batteries, type R-14, UM2 or C-cells. REMOTE CONTROL (for AZ1505 model only) 9 VOLUME 3 , 4 - adjusts volume level. SHUFFLE - plays all CD tracks in random order. 2; - starts or pauses CD playback. SEARCH 5 , 6 - searches backwards/ forwards within a track. PRESET + , (up, down) - selects a preset radio station. TUNING , (down, up) - tunes to tuner stations. 9 - to stop playback; - erases a CD program. , - skips to the beginning of a current track previous/ subsequent track. REPEAT - repeats a track /program/ entire CD.

POWER SUPPLY

IMPORTANT! Incorrect use of batteries can cause electrolyte leakage and will corrode the compartment or cause the batteries to burst. Do not mix battery types: e.g. alkaline with carbon zinc. Only use batteries of the same type for the set. When inserting new batteries, do not try to mix old batteries with the new ones. Batteries contain chemical substances, so they should be disposed of properly.
Using AC Power 1. Check if the AC power supply, as shown on the type plate located on the bottom of the set, corresponds to your local power supply. If it does not, consult your dealer or service centre. 2. Connect the mains lead to the wall socket. 3. To disconnect the mains supply, unplug the set from the wall socket. The type plate is located on the bottom of the set.

DIGITAL TUNER

DIGITAL TUNER Tuning to radio stations 1. Adjust the POWER slider to RADIO. tu is displayed briefly and then the radio station frequency, waveband and, if programmed, a preset number are shown. (See 3) 2. Press BAND once or more to select your waveband. 3. Press and hold SEARCH or until the frequency in the display starts running. The radio automatically tunes to a station of sufficient reception. Display shows Srch during automatic tuning. 4. Repeat step 3 if necessary until you find the desired station. To tune to a weak station, press or briefly and repeatedly until you have found optimal reception. To improve radio reception: For FM, extend, incline and turn the telescopic aerial. Reduce its length if the signal is too strong. For MW (AM or LW), the set uses a built-in aerial. Direct this aerial by turning the whole set. Programming radio stations You can store up to a total of 40 radio stations in the memory, manually or automatically (Autostore). Manual programming 1. Tune to your desired station (see Tuning to radio stations). 2. Press PROGRAM to activate programming. Display: Pr -- and PROG flashes. 3. Use the digit panel on the set to key in a number, 1-40, to select a preset station. E.g. press 1,1 if you want to store your station as preset 11. (See 4) Remote control (AZ1505 models only): Press PRESET + / once or more to select a preset station. 4. Press PROGRAM to confirm. 5. Repeat steps 1-4 to store other stations. Note : You can erase a preset station by storing another frequency in its place.

Important notes for users in the U.K.
Mains plug This apparatus is fitted with an approved 13 Amp plug.To change a fuse in this type of plug proceed as follows: 1. Remove fuse cover and fuse. 2. Fix new fuse which should be a BSAmp, A.S.T.A. or BSI approved type. 3. Refit the fuse cover. If the fitted plug is not suitable for your socket outlets, it should be cut off and an appropriate plug fitted in its place. If the mains plug contains a fuse, this should have a value of 5 Amp. If a plug without a fuse is used, the fuse at the distribution board should not be greater than 5 Amp. Note:The severed plug must be disposed of to avoid a possible shock hazard should it be inserted into a 13 Amp socket elsewhere. How to connect a plug The wires in the mains lead are coloured with the following code: blue = neutral (N), brown = live (L). As these colours may not correspond with the colour markings identifying the terminals in your plug, proceed as follows: Connect the blue wire to the terminal marked N or coloured black. Connect the brown wire to the terminal marked L or coloured red. Do not connect either wire to the earth terminal in the plug, marked E (or e) or coloured green (or green and yellow). Before replacing the plug cover, make certain that the cord grip is clamped over the sheath of the lead - not simply over the two wires. Copyright in the U.K. Recording and playback of material may require consent. See Copyright Act 1956 and The Performers Protection Acts 1958 to 1972.

1500 AZ1505

CAUTION Use of controls or adjustments or performance of procedures other than herein may result in hazardous radiation exposure or other unsafe operation.
This set complies with the radio interference requirements of the European Community. For users in the U.K., please follow the boxed instructions Important notes. on this sheet.

BASIC FUNCTIONS

POWER SUPPLY Whenever convenient, use the AC power supply to conserve battery life. Make sure you remove the power plug from the set and wall outlet before inserting batteries. Batteries (not included) Insert 6 batteries, type R-14, UM-2 or C-cells, (preferably alkaline) with the correct polarity. (See 7) Remote control (AZ1505 model only) Insert 2 batteries, type AAA, R03 or UM4 (preferably alkaline). (See 9)
Remote Control for AZ1505 model only
Switching on and off and selecting function 1. To switch on, adjust the POWER slider to select: CD, RADIO or TAPE function, and operate the respective function controls. 2. To switch off, adjust the POWER slider to select TAPE/OFF and make sure all the cassette keys are released. Note : The DBB setting, tuner presets and the volume will be retained in the set's memory. Adjusting volume and sound (See 2) 1. Press the VOLUME 3 or 4 controls to adjust the volume. 2. Press DBB once or more to select dynamic bass boost on or off.

CD PLAYER

Direct Easy Access Key in the number of the track using the digit panel on the set. SEARCH or Press SEARCH or once or repeatedly to select your track. Finding a passage within a track 1. Press and hold SEARCH or. The CD is played at high speed and low volume. 2. When you recognize the passage you want, release or to resume normal playback. Note : During a CD program or if SHUFFLE/ REPEAT active, searching is only possible within a track. Different play modes: SHUFFLE and REPEAT You can select and change the various play modes before or during playback, and combine the modes with PROGRAM. (See 5) SHUFFLE - tracks of the entire CD/ program are played in random order SHUFFLE REPEAT ALL - to repeat the entire CD/ program continuously in random order REPEAT ALL - repeats the entire CD/ program REPEAT - plays the current track continuously
3. Repeat steps 1-2 to select and store all desired tracks. Display: FULL if you try to program more than 20 tracks.
Reviewing the program In the stop position, press and hold PROGRAM until the display shows all your stored track numbers in sequence. Erasing a program You can erase the program by: pressing 9 twice CLr is displayed briefly and PROG disappears. You select TAPE or RADIO function. CASSETTE RECORDER Cassette playback 1. Adjust the POWER slider to TAPE. 2. Insert a cassette as shown and close the door. 3. Press 2 to start playback. Display: shows tAPE throughout tape operation. 4. To pause playback press PAUSE ;. Press again to resume. 5. Press SEARCH 5 or 6 to fast wind the tape. 6. To stop the tape, press STOP 9. The keys are automatically released at the end of a tape and the set switched off, except if PAUSE ; has been activated. General information on recording Recording is permissible insofar as copyright or. other rights of third parties are not infringed. For recording, use only NORMAL type cassettes (IEC type I) on which the tabs have not yet been broken. This deck is not suited for recording on CHROME (IEC II) or METAL (IEC IV) type cassettes. The best recording level is set automatically. Altering the VOLUME or DBB controls will not affect the recording.

CASSETTE RECORDER

To protect a tape from accidental erasure, break out the tabs. If you wish to record again, cover the tabs with a piece of adhesive tape. CD Synchro Start Recording 1. Adjust the POWER slider to CD. 2. Insert a CD and if desired, program track numbers. 3. Insert a suitable tape into the cassette deck and close the door. 4. Press RECORD 0 to start recording. Playing of the CD program starts automatically from the beginning of the program. You don't need to start the CD player separately. To select and record a particular passage within a CD track: Press SEARCH or. Release the control when you recognize the passage you want. To pause CD playback, press 2;. Recording starts from this exact point in the track when you press RECORD 0. 5. To pause recording, press PAUSE ;. Press PAUSE ; again to resume recording. 6. To stop recording, press STOP 9. Recording from the Radio 1. Tune to the desired radio station (see Tuning to radio stations). 2. Follow steps 3-6, under CD Synchro Start Recording.

English Franais Espaol Deutsch Nederlands

AZ 1500 AZ 1505

CD PLAYER Playing a CD This CD player plays Audio Discs including CDRecordables and CD-Rewritables. 1. Adjust the POWER slider to CD. 2. Insert a CD with the printed side facing up and close the door. noCd if no CD inserted/ CD dirty, incorrectly inserted or damaged. nFCd if you have inserted a non-finalized CDR(W). 3. Press 2; to start playback. dAtA if your CD contains non-audio i.e. data files. 4. To pause playback press 2;. Press 2; again to resume play. Display: 2 flashes during pause. 5. To stop CD playback, press the 9 button. Note : CD play will also stop when: - the CD-tape door is opened - the CD has reached the end - you select TAPE or RADIO function. Selecting a different track There are 2 ways:

CLASS 1 LASER PRODUCT

2892.1
1. To select play mode, press MODE once or more. 2. Press 2; to start playback if in the stop position. 3. To select normal playback, press MODE repeatedly until the various modes are no longer displayed. You can also press the 9 button to cancel your play mode.
Programming track numbers In the stop position, select and store your CD tracks in the desired sequence. Up to 20 tracks can be stored in the memory. 1. Press SEARCH or on the set to select your desired track number. 2. Press PROGRAM. Display: PROG, Pr and your selected track number. (See 6) If you attempt to program without first selecting a track number, noSE is shown.
LECTEUR DE CD Lecture de CD Ce lecteur CD peut jouer toutes sortes de disques audio tels que des CD r-enregistrables et des CD rimprimables. 1. Slectionnez la source CD. 2. Inserez un CD avec le ct imprim orient vers le haut et fermez le compartiment CD. noCd si absence de disque/ CD ray, contamin ou incorrectment insr. nFCd un CD-R(W) est vierge ou le disque na pas t finalis. 3. Appuyez sur 2; pour dmarrer la lecture. dAtA si votre CD contient des fichiers nonaudio. 4. Pour interrompre la lecture, appuyez sur 2;. Appuyez une nouvelle fois sur 2; pour reprendre la lecture.

$ #@ !

1. Pour slectionner un mode de lecture, appuyez sur MODE une ou plusieurs fois. 2. Appuyez sur 2; pour dmarrer la lecture en position d'arrt.

Printed in Hong Kong

SAFETY & MAINTENANCE INFORMATION
SAFETY & MAINTENANCE INFORMATION (See 8) Don't expose the set, batteries, CDs or cassettes to humidity, rain, sand or excessive heat. Clean the set with a dry cloth. Don't use any cleaning agents containing alcohol, ammonia, benzene or abrasives as these may harm the set. Place the set on a hard and flat surface so that the system does not tilt. Make sure there is good ventilation to prevent the set overheating. The mechanical parts of the set contain selflubricating bearings and must not be oiled or lubricated. CD player and CD handling If the CD player cannot read CDs correctly, use a cleaning CD to clean the lens before taking the set to repair. The lens of the CD player should never be touched! Sudden changes in the surrounding temperature can cause condensation on the lens of your CD player. Playing a CD is then not possible. Do not attempt to clean the lens but leave the set in a warm environment until the moisture evaporates. Always close the CD-tape door to avoid dust on the lens. To clean the CD, wipe in a straight line from the centre towards the edge using a soft, lint-free cloth. Do not use cleaning agents as they may damage the disc. Never write on a CD or attach any stickers to it. Tape deck maintenance To ensure quality recording and playback of the tape deck, clean parts A, B and C as shown, once a month. Use a cotton bud slightly moistened with alcohol or a special head cleaning fluid to clean the deck. 1. Open the CD-tape door. 2. Press PLAY 2 and clean the roller C. 3. Press PAUSE ; and clean the heads A, and the capstan B. 4. After cleaning, press STOP 9.

CD Soundmachine

Easy access keyboard Digital tuner with 40 station presets Autostore programming Dynamic bass boost Bass reflex speaker system CD-Rewritable compatible 20-track CD programmable Shuffle play
Standard product information CD player
Toploader with manual door 20-track CD programmable Shuffle play CD synchro-start recording CD-Rewritable compatible Repeat one/ all/ program CD next/ previous track search
Easy access keyboard Well-known 10 button interface for easiest possible tuner preset and CD track access. Digital tuner with 40 station presets Provides fast, accurate tuning to your favourite stations. You can store up to 40 FM and MW stations in memory for fast, easy access. Autostore programming Automatic programming of strongest available radio stations. Dynamic bass boost An electronic circuit that enhances bass frequencies up to 3 times to compensate for the insensitivity of the human ear for bass frequencies at lower volume levels. Bass reflex speaker system Acoustic system that enhances the upper bass tones to provide a warmer, punchier bass sound. CD-Rewritable compatible CD player capable of playing all music CDs, including CD-Recordable and CD-Rewritable discs. 20-track CD programmable Stores up to 20 of your favourite CD tracks for playing back in your order of preference. Shuffle play Plays all selections on a disc in random order, giving you a new sequence of tracks every time.
Digital up/ down volume control Accurate electronic volume control with level indication. CD Synchro-start recording One button touch will synchronize the start of a recording on audio cassette and the start of a CD or CD program. 4 Full-range speakers For excellent sound reproduction across the entire audio spectrum. Full auto-stop tapedeck Automatically shuts off the cassette deck at the end of playback to avoid stretching the tape. Repeat one/ all/ program Repeats the current track, the total CD, or your pre-selected program. Stereo headphone socket Supports stereo headphones for private listening pleasure. Automatically switches off speakers when used. 4-digit Multi-functional LCD display Displays CD player information (track, time, play mode), tuner information (preset station, frequency) and DBB on/off.
Digital tuning system 40 station presets Autostore presets for quick programming Direct preset input via Easy access keyboard Telescopic antenna for FM reception Internal antenna for AM reception Wavebands FM stereo AM/ MW LW (only for Europe)

Tapedeck

Automatic recording level Full auto-stop

Sound system

Output power 2 x 1 W RMS Dynamic bass boost 2 x 4 speakers Metal speaker grilles Digital up/ down volume control

Display

4-digit multi-functional LCD

Connections

Headphone/ line out Stereo, 3.5 mm

Power supply

AC/ DC operation Batteries 6 x 1.5V, R14

General

Product dimensions (mm) Product weight (kg) Package dimension (mm) Weight incl packing (kg) 405 W x 162 H x 232 D 3.W x 211 H x 260 D 3.8
Printed in Hong Kong 2001-11-12 Specifications subject to modification without notice 2001 Koninklijke Philips Electronics N.V. All rights reserved www.philips.com www.audio.philips.com