SAFETY INSTRUCTIONS 3

2 Product description

2.1 Front view

English 5 6
1 Stand-by button: 2 OK button: 3 Smart card reader. 4 "W" button: 5 Red LED indicator: 6 V button:
Switch receiver ON or Standby. Reset the receiver, in case of hanging up, after a 5 second keypress. Button to confirm your selection.
Channel down. Is lit whenever the receive is in stand-by mode (*). Channel up.
(*): Note: if the LED is slowly blinking, it indicates that a free over the air upgrade of your receiver is taking place. Do not interrupt this operation which may last several minutes. Wait until the LED stops blinking. The LED blinks rapidly when receiving remote control signal. When the receiver is operating, the LED is turned off. To check whether the receiver is properly powered, remove the power plug and plug it back in. The front panel LED will blink once.

4 PRODUCT DESCRIPTION

2.2 Rear view
1 TV (*): 2 Digital audio output (*): 3 Serial (*):
SCART (1) socket to connect to your TV set. Coaxial Digital audio output to connect your HIFI / Audio receiver system. RJ 9 socket for serial data transfer during servicing.
4 230V~50Hz 25W max (**): Socket to connect the Mains cord. 5 Label showing the type and serial number of the receiver. 6 VCR (*): 7 L/R Audio out (*): 8 SAT IN (*):
SCART (1) socket to connect your video recorder. Left/Right audio-cinch outputs to connect your HIFI / Audio receiver system. Socket for satellite dish.
1) SCART is also called Euroconnector or Peritel. (*): SELV: Safety Extra Low Voltage. (**): HV: Hazardous Voltage.

PRODUCT DESCRIPTION 5

English

2.3 The remote control

SATELLITE MODE (SAT)
Detailed information about a programme or selection of language and/or subtitling.

Standby B On/Off button.

INFO To display on screen an information bar with information about the programme.
A, B, C, D, E: Function buttons.
MENU To reach the main menu.

8 CONNECTING UP THE RECEIVER
3.1 Connecting to your HiFi/Audio receiver equipement (Analogue/Digital)

Satellite receiver HiFi

Depending on your HiFi / Audio receiver equipment, you might have several options to connect your digital receiver. ANALOGUE CONNECTION Connect the L/R audio output sockets to the relevant L/R audio input sockets of your audio equipment using a double CINCH cable (not supplied). Consult the user manual of your HiFi/Audio receiver equipment to choose the proper analogue audio inputs. Note: With this connection set up you can control the audio volume up/down and mute using your digital receiver or Hi-fi remote control. DIGITAL CONNECTION Connect the audio "DIGITAL" output socket to the relevant digital audio input socket of your audio equipment using a single CINCH cable (not supplied). Consult the user manual of your HiFi/Audio receiver equipment to choose the proper digital audio input. Note: With this connection set up you can only control the audio volume up/down and mute with your HiFi / Audio Receiver remote control, refer to the relevant user manual.
CONNECTING UP THE RECEIVER 9

4 Menu structure

Setting the time and the channel to tape a video. Setting your favourite channels.
1 PROGRAMMAS OPNEMEN 2 VOORKEURKANALEN KIEZEN 3 CODE EN KINDERSLOT 4 INSTELLINGEN 5 KANALEN INSTALLEREN 6 INFORMATIE ABONNEMENT EN BRIEVENBUS 7 TECHNISCHE INFORMATIE
Entering and altering of the code and entering of a parental lock. Installation of the receiver, TV, VCR and modem. To enter, add and remove channels, to alter the sequence of the channels and the summary of the channel list. To consult the period of validity of the subscription and read the CanalDigitaal messages. Checking the reception signal strength, installation of the aerial and consulting the decoder and software version.

INSTELLINGEN

Altering the volume, subtitling, spoken language, length of time the information bar remains on the screen, the reminder and the time. Altering the TV and VCR standard settings.

TECHNISCHE INFORMATIE

1 SIGNAALSTERKTE
Checking the LNB installations and setting the aerial. Consulting the decoder and software version.

2 DECODERVERSIE

10 M E N U S T R U C T U R E
5 Installing the satellite receiver
How to install your satellite receiver:
1 Turn on your TV. 2 When you power on the box, the front LED will blink
once and switch off. The Menu screen will then appear. Make sure your smart card is inserted in the slot, the chip facing upwards. Now, you can only access options 4,5 and 7. If the MENU screen doesn't appear after you have switched on the receiver, then press the TV/SAT button on your remote control twice. Note: Generally, when you don't have any screen after having connected you, press the TV/SAT button twice on your remote.
3 Execute the following three steps to install the receiver:

Step 1 Step 2 Step 3

INSTELLINGEN (Button 4) TECHNISCHE INFORMATIE (Button 7) KANALEEN INSTALLEREN (Button 5)

Installation

Installation of the decoder
You access the menu by pressing the MENU button. To choose one of the options in the MENU you can press one of the selected numbers or you can select the option with the arrows. Press OK to confirm your choice. Choose option 4 in the menu (INSTELLINGEN) and then 1 (INSTELLEN DECODER). With this MENU, you can select your favourite installation for your satellite receiver. Select the number to of the function you've chosen or use the buttons make your selection. The possible options appear when you press the arrows. 5.1.1.1 Preferred language You can choose between English, Dutch, Spanish, French, German, Italian or the original version. This option can only be selected if the programme is also subtitled with the selected language. 5.1.1.2 Subtitling You can choose between English, Dutch, Spanish, French, German, Italian or without subtitling. This option can only be selected if the programme is broadcast in the selected language. I N S TA L L I N G T H E S AT E L L I T E R E C E I V E R 11
A TERUG NAAR MENU 4.1 INSTELLEN DECODER
5.1.1.3 Sound With this option, you choose the standard level of the volume. When you watch a programme, you can adjust the volume with the buttons. 5.1.1.4 Duration of the information bar With this option, you choose how long the bar with the name and the number of the selected channel must remain on the screen. You can choose a normal or long time or no bar. English
4.2 INSTELLEN TV EN VIDEORECORDER 1 BEELDFORMAAT TV 2 GELUID TV 3 SIGNAAL TV 4 GELUID VIDEORECORDER 5 NORM VIDEORECORDER 4/3 (STANDAARD) STEREO CVBS STEREO PAL A TERUG NAAR MENU
5.1.1.5 Reminder/Alarm It indicates automatically when a programme you have chosen starts. You can choose a reminder for video and audio or for video only. 5.1.1.6 Setting the time The right date and time will be set automatically in the satellite receiver once the installation has been completed. But you can also set the time manually. To do so, press the B button. Then press the A button twice to return to the main menu.
Installation of the TV / Videorecorder
Choose option 4 (INSTELLINGEN) in the menu and then option 2 (INSTELLEN TV EN VIDEORECORDER). Here you have the possibility of making the optimum installations for your TV and VCR. To go from one option to another one, press the number of the option you have chosen or press the buttons on the remote control. To choose one of the various possibilities, you can press the buttons.

1 BEELDFORMAAT TV 4 5

: 4/3 standard or 16/9 large frame GELUID TV : stereo or mono SIGNAAL TV : we advise you to switch it to RGB GELUID VIDEORECORDER : stereo or mono NORM VIDEORECORDER : we advise you to keep it on PAL When you have selected the installations you wanted, you may press on the A button to return to the INSTELLINGEN screen.
12 I N S TA L L I N G T H E S AT E L L I T E R E C E I V E R

Technical information

Installation of the dish
SATELLIET : ASTRA 1G SCHOTELNUMMER : 1 BAND : KU FREQUENTIE : 12.515 Ghz LO LNB : 10600 Mhz POLARISATIE : Horizontal Schakeling (22Khz) : Yes If you use another satellite, in the section SATELLIET you can select "OVERIGE" and enter the necessary parameters. Check in every case the LO and LNB values. You will find them in the manual for the dish aerial or on the sticker of the LNB. Contact the dealer who supplied you with the dish if you don't find these values. Once the right parameters have been installed, you can begin installing the channels.
Positioning the satellite dish
We advise you to have the dish installed by a professional with suitable measuring devices. 1 Return to the screen SIGNAALSTERKTE (Press B). 2 Select VOEDINGSSPANNING LNB with the help of the arrows. JA (Yes) if you have one satellite dish. NEE (No) if you have connected several dishes up to your decoder. In that case, please contact your dealer. 3 Put the dish in direction 19,2 East of the ASTRA satellite position. 4 On the screen, you will see a receivingsindicator which indicates the quality and strength of the reception. The length of the bar indicates the strength and the colour the quality. Position the dish as well as possible: the bar must be as long as possible. If the signal quality is green and reaches almost 3, the strength of the signal is acceptable. You may fix the dish in this position. I N S TA L L I N G T H E S AT E L L I T E R E C E I V E R 13
From the menu, press 7 (TECHNISCHE INFORMATIE) and then 1 (SIGNAALKWALITEIT). With the screen SIGNAALKWALITEIT, you can find out the strength of the signal received. We advise you to have the dish installed by a professional with suitable measuring devices. For the reception of the digital signal of the ASTRA satellite, all the parameters are already installed. To alter these settings, press on B (ANTENNE INSTELLEN).
If the signal quality is orange, you may change the direction of the dish in order to get a better signal. If the signal quality is red, the signal is bad. The signal may be bad when: - the dish is not positioned in the right direction. - the connection between the dish and the decoder with the feeder is not well made. In that case, please contact your dealer. When the receiving indicator is green and in the region of 3, the decoder is ready to have the channels input.

5 KANALEN INSTALLEREN 1 LIJST VAN KANALEN 2 KANALEN HERNUMMEREN 3 KANALEN TOEVOEGEN 4 KANALEN VERWIJDEREN 5 KANALEN INSTALLEREN A TERUG NAAR MENU 5.5 KANALEN INSTALLEREN 1 CANAL DIGITAAL 2 IN WILLEKEURIGE VOLGORDE A TERUG NAAR VORIG SCHERM

Storing the channels

Select KANALEN INSTALLEREN (button 5 in the menu). The following screen then appears:

Canal digitaal

If you choose this method, the channels of CANALDIGITAAL will be stored first as per the order of CANALDIGITAAL in the Channel List. Then, the other channels will follow in a indeterminate order. The decoder allows you to give new number to the "remaining channels" (the numbers of the CANALDIGITAAL channels may not however be changed). With this option, the searching process will last about 15 to 30 minutes. During this operation, a progress display appears on the screen. When the channels have been found (the display shows 100%), a list of all the channels is automatically stored in the decoder.
In an indeterminate order
If you choose this method, the channels will be stored in an indeterminate order in the Channel List. The decoder allows you to give new number to all the channels (incl. CANALDIGITAAL). The searching process will last about 15 to 30 minutes. During this operation, a progress display appears on the screen. When the channels have been found (the display shows 100%), a list of all the channels is automatically stored in the decoder. 14 I N S TA L L I N G T H E S AT E L L I T E R E C E I V E R

6 The menu

Code and parental lock
Button 3 of the MENU You may personally enter the code or change it. When you want to watch a locked programme or a programme you have to pay for, you always have to enter this pincode. You can also lock some channels with a parental lock.

3 PINCODE EN KINDERSLOT

Entering a code
Press MENU, and then 3 and 1. Choose a 4-digit number (not 0000). If you want to change your code, choose option 1 again (CODE WIJZIGEN). Confirm your CODE by pressing OK or by returning to the screen CODE EN KINDERSLOT and pressing A.
3.2 KINDERSLOT ACTIVEREN CANAL DIGITAAL KINDERSLOT NIET ACTIEF. C+C+RTLRTLSBSVERONICA 6 TMF 7 NEDNED2 9. OK BEVESTIGEN B KINDERSLOT ACTIVEREN A TERUG NAAR MENU

Using the parental lock

With this option, you lock and unlock one or more channels. Press MENU, then 3 and then 2. You have to enter your pincode first. On this screen, it is possible to: - Select the channels you want to lock. When you've selected a channel, a small lock appears on the screen. - Press the B button to change the status of the parental lock. The symbol of an open lock becomes a closed lock or vice-versa.

7.1 The bottom bar

On this bar, you will see the number and the name of the channel you are watching, as well as the time.

7.2 The top bar

On this bar, you will find information about the programmes and further information about the channel you are watching. This information is given with symbols. Here you will find the name and the number of the channel, the title and type of programme you are watching, the time of start and finish of the programme and technical information (stereo sound, format). To see all the programmes which are broadcast at the same moment: - Press the arrow buttons to select the channel or press directly the number of the channel you are interested in. The top bar changes whilst the bottom bar and the picture you are looking at remain the same. To see the following programme on the channel: - Press the button. Now you can see what will be broadcast later.
I N F O R M AT I O N S B A R S 19
8 Electronical programme guide (EPG)
EPG button The electronical programme guide (EPG) gives you information about all the programmes that will be broadcast next week. With EPG you can look for programmes very easily. With the EPG button, you can access the following options: PROGRAMMA OVERZICHT: The programmes are listed in the order of their broadcasting per channel. FILM, SPORT, JEUGD, DOCUMENTAIRES EN OVERIGE GENRES: The programmes are listed per theme (movies, sports, youth, documentaries and other kinds of programmes). SELECTEREN PROGRAMMA'S: Here you can make selections to look for your favourite programmes. The programmes you've selected are stored in the memory. LIJST GESELECTEERDE PROGRAMMA'S: a list with all the programmes you have selected and want to see or record. To leave the ELECTRONICAL PROGRAMME GUIDE, press EPG or TERUG. Note: It can happen that the EPG is not completely updated with the actual information. Because of the actual regulation concerning the copyrights of programmes of the broadcasters Nederland 1-2-3, Canal + is limited in the broadcast of the Electronical Programme Guide.
8.1 List of the programmes
Here you find all the programmes in chronological order. You can consult all the programmes up to one week ahead.
8.1.1 Choosing a programme
When you want to watch a programme, you can select it with the arrow buttons or and than you can press the OK button in order to: - know if a programme is being broadcast at that moment, - store a programme which is being broadcast later in the memory, - delete a programme which has been stored in the memory, - request a programme you have to pay for.This function will only be available at a later date, - record a programme or cancel a recording.

8.1.2 Programmes broadcast on other days
When you want to look for a programme which is broadcast on a given day in the EPG, you can perform the following operation: - to select the day: - Press the button corresponding to the selected day of the week (MA, DI,.) and go directly to the time (morning) from 6:00 to 14:00. - For afternoon programmes between 14:00 and 20:00 press the DAG button. - For evening programmes between 20:00 and 24:00 press the AVOND button. - For night programmes between 00:00 and 6:00 press the NACHT button.
20 E L E C T R O N I C A L P R O G R A M M E G U I D E
+ button When you press the + button, you will get detailed information about the selected programmes (summary of the programme, actors, presentators, directors, producers,.).
8.2 Films, sports, youth, documentaries and other kinds of programmes
Here you find all the programme which are selected according to the various kinds: films, sports, programmes for young people and other kinds of programmes in chronological order. You can search for the programmes up to one week ahead. When you choose ANDERE GENRES (with the arrow buttons or OK ), you will see the following list: - Series - News magazines (Infomagazine) - Entertainment - Music (Muziek) - Weather forecast (Weerbericht) - Events (Evenement) - Others (Overige)
When you press PROGRAMMA OVERZICHT and then B, you can choose a programme on the basis of the channel and the starting time. When you press OK, the EPG will look for the corresponding programme. Then you may store this channel in the LIJST GESELECTEERDE PROGRAMMA'S.

8.1.4 Reminder

The receiver will warn you when a progamme you have entered in the LIJST GESELECTEERDE PROGRAMMA'S is going to start. You can install the warning signal via the MENU. Press MENU and then 4 and 1. A few minutes before the beginning of the programme, you will be warned. In HERINNERING you can choose: - audio: the decoder will utter a BEEP. - None. When you press the + button, the name of the programme you have stored in the memory will appear. WARNING! - When a programme which has been stored is broadcast, it will be automatically erased from the memory. - A maximum of 8 programmes can be stored in the memory. - A programme which has been stored is indicated in the EPG or INFO with a symbol.

8.2.1 Choosing programme

When you want to watch a programme, you can select it with the arrow buttons or or press the OK button to: - see if the programme is being broadcast at that moment. - store a programme which will be broadcast later in the memory. - delete a programme from the memory. - request a programme you have to pay for. This function will be available only in the future. - record a programme or cancel a recording.

8.2.2 Programmes broadcast on other days
When you want to look for a programme which is broadcast on a given day in de EPG, you can perform the following operation: - Press the button corresponding to the selected day of the week (MA, DI,.) and go directly to the time (morning) from 6:00 to 14:00.
E L E C T R O N I C A L P R O G R A M M E G U I D E 21
8.1.3 Choosing programmes on the basis of the channel or the time
- For afternoon programmes between 14:00 and 20:00 press the DAG button - For evening programmes between 20:00 and 24:00 press the AVOND button. - For night programmes between 00:00 and 6:00 press the NACHT button. + button When you press the + button, you will get detailed information about the selected programmes (summary of the programme, actors, presentators, directors, producers,.).
WARNING! - When a programme which has been stored is broadcast, it will be automatically erased from the memory. - A maximum of 8 programmes can be stored in the memory. - A programme which has been stored is indicated in the EPG or INFO with a symbol.

8.3 Selecting programmes

With this option, you can select your favourite programmes on the basis of various criteria. If you choose SELECTEREN PROGRAMMA'S and then D (select), you have the choice between three possibilities: - Theme (Genre) - Time (Tijdstip) - Channel (Kanaal) When you have adapted the criteria to your own preferences, you can search for a programme with the E button. With the + button, you can request further information. With the B button, you can, by adding the start time of the programme, include an extra criterion in the search.
8.2.3 Choosing programmes on the basis of time
When you select FILM, SPORT, JEUGD, DOCUMENTAIRES EN OVERIGE GENRES (movies, sports, youth, documentaries or other kinds) and then press B, you can select a programme on the basis of the starttime. After that, when you press OK, the EPG will look for the corresponding programme. Then, you can store this channel in the LIJST GESELECTEERDE PROGRAMMA'S.

8.2.4 Reminder

The receiver will warn you when a programme you have entered in the LIJST GESELECTEERDE PROGRAMMA'S is going to start. You can install the type of warning signal via the MENU. Press MENU and then 4 and 1. A few minutes before the beginning of the programme, you will be warned. In HERINNERING you can choose: - audio: the decoder will utter a BEEP. - None. When you press the + button, the name of the programme you have stored in the memory will appear.
8.4 List of selected programmes
In the list of the selected programmes you will find all the programmes you have stored in the memory of the receiver. Here you will find two types of programmes: - programmes you have selected in the MENU to be recorded (indicated with PROGRAMMERING OPNAME) ; when these programmes start, the receiver will automatically switch on the channel on which the programme is to be broadcast. - programmes you've selected in the EPG ; when these programmes start, the receiver gives you a warning signal. - You can also delete a programme from this list by selecting the programme and pressing OK.

24 T H E C H A N N E L S

11.3 Adding new channels
It can happen that new digital channels are launched. You may add these new channels in the memory of your decoder. You may add new channels with the menu KANALEN INSTALLEREN: - press MENU and 5. - choose then option 3 (KANALEN TOEVOEGEN). On this moment, the decoder will start searching automatically. A progress display will appear on the screen.when the search is complete, you will find the new channels in the LIJST VAN KANALEN.
11.5 Reinstalling channels
During the installation, you had to choose between the numbering of CANALDIGITAAL or a random numbering. This option gives you the possibility to go from one type of numbering to another one. English press MENU and then 5. choose then option 5 (KANALEN INSTALLEREN). Press OK so that the display KANALEN INSTALLEREN appears. The system warns that the complete list of channels can be altered and that you have to enter your CODE to access this menu. now you may choose again between both kinds of numberings of the channels.

11.4 Removing channels

You may also remove channels which are stored in the memory with the help of the menu KANALEN INSTALLEREN: - press MENU and then 5. - choose then option 4 (KANALEN VERWIJDEREN). A list of channels you may remove appears on the screen. You may select the channel with the arrow buttons. Then you can remove the channel by pressing OK. The channel which has been removed will be restored in the memory by installing the channels once again.

T H E C H A N N E L S 25

12 Subscription programmes

(not yet available)

When this manual was being printed, subscription programmes were not yet available. You will be informed when these services will be available.
13 Information for subscribers
When you press the SERV button whilst watching one of the channels of CANADIGITAAL, you may request information abouth various subjects.
14 Symbols and abreviations
FAVOURITE CHANNEL This symbol indicates which channels you have selected as being your favourite channels. THE PROGRAMME IS BEING BROADCAST NOW This symbol indicates that a programme is being broadcast at this moment. By pressing OK you go directly on this programme. A PROGRAMME IN THE MEMORY Programmes you have stored in the LIJST GESELECTEERDE KANALEN are recognizable by this symbol. PROGRAMMED FOR RECORDING WITH THE VCR This symbol indicates in the EPG that a programme has been selected to be recorded with the videorecorder. CHANNEL WITH PARENTAL LOCK This symbol indicates in the EPG and INFO that a channel has been locked with a parental lock. Only the persons knowing the code will be able to watch this channel. When the lock is open, the parental lock is not active. ORIGINAL VERSION, SUBTITLING These are abbreviations which are used to indicate how a programme is being broadcast: in the original language or with a subtitling. This symbol appears in the top bar when you press INFO. PROGRAMME FORMAT These abbreviations indicate the format in which the programme is being broadcast. 16/9 means large format and 4/3 normal format. These symbols appear in the top bar when you press INFO.

Check the batteries and change them eventually.

Choose another service.

16 Technical specifications
This product is in conformity with the requirements of the 95/47/EC and 2002/21/EC directives. Video decoding - MPEG-2 DVB compliant up to MP@ ML - Video bit rate: up to 15 Mbit/sec - Video format: 4 :3 and 16 :9 - Resolution: up to 720x576 pixels Audio decoding - MPEG layer I / II (excluding multi-channel management from one bitstream) Ease of Installation - Automatic program installation via scanning - Automatic program list update - Program editing for personalised installation Ease of Use Zaplist Favourite mode Full remote controlled Automatic recording by tagging via EPG Application system resources Processor clock speed 166 MHz SDRAM-CPU/Video-Graphics 8 MB Flash memory 8 MB Satellite antenna interface RF input: IEC169-24F LNB supply: 0 / 14 / 18V LNB current: 350 mA max Tone switching: 22 kHz (on / off) Tone burst for 2 orbital position Accessories Remote control: RC2585102/01 Scart cable Instruction for use Batteries: 2 x 1.5V type AA/LR6 Mains cord (2 m)
Miscellaneous - Temperature range (C) Operating: +5 to 45 Storage: -10 to +70 - Mains: 230 V ~ +/-10% 50 Hz
Reception-Demodulation - Demodulation type: QPSK - Input frequency range: 950-2150MHz - Input level range: -65 to -25 dBm - Satellite band coverage: C and Ku band De-scrambling Type: DVB Implementation: Internal Smart card: 1 for CA Note: subscription is required for the reception of Canal Digitaal/Cyfra+ scrambled services Connections TV SCART Output: CVBS, Controlled audio L/R, RGB, Slow blanking, Fast blanking VCR SCART Input: CVBS, Slow blanking, Audio L/R Output: CVBS, Y/C (SVHS), Audio L/R Analog Audio output: Controlled Audio Cinch L/R Digital Audio output: PCM Serial interface: RS 232 / RJ9 female
- Power consumption: 25 W max - Standby consumption: 6 W max - Weight: Including packaging: - Dimensions: Product: Packaging: 1.450 kg 2.5 kg
Operation/Features - Free to air reception with supplied smart card - Volume control - 8 event timers - Subtitles - Program parental lock with PIN code - Audio mode: single channel, dual channel, stereo, joint stereo - Menu controlled installation and operation using On Screen Display - Variable LNB frequency - Receiver compatible with Canal Digitaal/Cyfra+ services
The product complies with the following European council Directives: - 73/23/EEC - 93/68/EEC - 89/336/EEC
07/03 - Due to continued product improvements, this information is subject to change without notice.
T E C H N I C A L S P E C I F I C AT I O N S 29
17 More on your remote control
Setting up your remote control By default, your remote control is preset to control most of the Philips audio video appliances. If you have other brands of appliances, or if the presets do not control your Philips appliance, please follow the following procedure. Note: some of the functions described in the next pages may not be available or have the same behaviour for all appliances. 1. using the mode button, go to the destination mode which you want to set up (TV, VCR, DVD or Amp/Tuner). 2. Press digits 1 and 3 simultaneously for 3 seconds. After 3 seconds, the lights corresponding the the destination mode will blink twice and remain on. 3. Enter the 4 digit code within 60 seconds. You will find a list of codes at the end of this manual. (If several codes are possible, go through this procedure with the 1st code and try your remote control. If you are not successful, repeat the procedure with the second code, and so on). 4. If a valid 4-digit code has been entered, the lights will switch off and blink twice. If not, go back to step 1. Pressing any key other than digit keys and stand-by button will automatically exit this procedure. English If you wish to check that you have entered the right code. 1. press digits 1 and 6 simultaneously for more than 3 seconds. The destination mode lights will blink twice and turn off. 2. Press digit 1: the number of blinks of the destination mode light is the first number of the code. 3. Press digit 2: the number of blinks of the destination mode light is the second number of the code. 4. Press digit 3: the number of blinks of the destination mode light is the third number of the code. 5. Press digit 4: the number of blinks of the destination mode light is the fourth number of the code. No blinks indicates a zero. Keys should be pressed within 60 seconds of each other in order not to exit the procedure. At the end of the procedure, the remote control will return to normal mode.

0036, 0064, 0274 0064, 0114, 0309, 0097, 0274, 0039, 0064 0064, 0543, 0129, 0036, 0401 0362, 0265, 0136, 0064, 0652 0243, 0291, 0398, 0190, 0439, 0373, 0099, 0190, 0235 0131, 0373, 0132, 0244, 0099, 0064, 0114, 0543, 0129, 0438, 0097 0064, 0036, 0099, 0244, 0243, 0265, 0274, 0321, 0401, 0438, 0695 0131, 0244, 0099, 0114, 0397, 0072, 0235, 0063 0482, 0064, 0099, 0245, 0291, 0637 0243, 0114, 0064 0064, 0397 0129, 0397, 0036 0244, 0190, 0274, 0036, 0291 0129, 0233, 0099, 0244 0321, 0291 0036, 0245, 0244, 0543, 0099, 0190, 0064, 0129 0064, 0397 0036, 0245, 0036, 0190 0064, 0274, 0404, 0244, 0317, 0243, 0136, 0190
Goldline Gooding Goodmans
Gorenje Gradiente Graetz Granada Grandin Grundig HCM HMV Halifax Hampton Hanimex Hanseatic Hantarex Hantor Harwood Hema Hifivox Hikona Hinari Hisawa Hit Hitachi
Hornyphone Huanyu Hyper Hypson ICE ICeS IR
0064, 0398, 0036, 0099, 0063, 0245, 0507, 0244, 0401, 0514, 0651, 0291, 0362, 0543, 0543, 0064, 0099, 0235, 0072, 0135, 0244, 0253, 0366, 0500 0482, 0064, 0309, 0637, 0606, 0036, 0190, 0401 0097, 0222, 0514, 0064, 0036, 0583, 0614 0036, 0291, 0439, 0064, 0244, 0245, 0309, 0244 0243, 0036, 0421, 0064, 0546, 0309, 0244, 0404, 0583 0064, 0036, 0064, 0439 0244, 0036 0223, 0036, 0245, 0063, 0064, 0514, 0382 0482, 0309, 0637, 0245, 0190, 0221, 0244, 0605, 0223, 0136, 0746, 0099, 0063, 0225, 0500, 0543, 0132, 0243, 0401 0243, 0036, 0274, 0244 0064, 0291, 0309, 0482, 0427 0245, 0398, 0243, 0291, 0244, 0583 0243, 0245 0064, 0114, 0190, 0244, 0543, 0222, 0233, 0274, 0354, 0037, 0038, 0063, 0097, 0099, 0129, 0132,

36 S E T U P C O D E

ITS ITT ITV Iberia Imperial Indiana Ingelen Ingersol Inno Hit Interbuy Interfunk Internal Intervision
Irradio Isukai JVC KB Aristocrat KTV Kaisui Kamp Kapsch Karcher Kasui Kathrein Kendo Kennedy Kingsley Kneissel Kolster Konka Korpel Korting Kosmos Koyoda Kraking Kyoshu
0221, 0539, 0039, 0072, 0120, 0128, 0131, 0135, 0136, 0223, 0243, 0253, 0265, 0317, 0318, 0319, 0321, 0397, 0401, 0583 0291, 0243, 0398 0190, 0507, 0500, 0235, 0366, 0373, 0637 0064, 0274, 0445, 0397, 0099, 0244, 0317, 0543, 0036 0064, 0291 0064, 0190, 0039, 0114, 0539, 0354, 0064, 0482, 0129, 0291, 0309, 0245, 0274, 0404, 0513, 0244, 0421, 0514, 0546 0274, 0245, 0317, 0398 0064, 0245, 0309, 0482 0398, 0063, 0245, 0680, 0244 0245, 0309, 0064, 0243, 0482, 0244, 0233, 0190, 0131 0129, 0637, 0583 0438, 0637, 0064, 0129, 0274 0233, 0064, 0462, 0265, 0286, 0319, 0637, 0401, 0398, 0439

0039, 0583, 0114, 0064, 0401 0243, 0114, 0513 0064, 0039, 0114, 0243 0136, 0064, 0513, 0036, 0064, 0064, 0606 0064, 0364, 0129, 0445, 0036, 0695, 0244, 0274, 0291 0064, 0039, 0583, 0064, 0097, 0539, 0101, 0037, 0038, 0131, 0227, 0120 0114, 0064, 0245, 0064, 0039, 0244 0543, 0114, 0274, 0064 0606, 0064, 0036, 0233, 0286, 0438, 0190, 0291 0036, 0291, 0064, 0245, 0439 0039, 0064 0064, 0129, 0244, 0036, 0291, 0695, 0063 0037, 0129, 0114, 0233,

38 S E T U P C O D E

SEI-Sinudyne Saba Saccs Sagem Saisho Salora Sambers Samsung
Sandra Sansui Sanyo Schneider Scotland Seleco Sencora Sentra Serino Sharp Shintoshi Shorai Siarem Siemens Silva Silver Singer Sinudyne Solavox Sonitron Sonoko Sonolor Sontec Sony Sound & Vision Soundwave Ssangyong Standard Stenway
0321, 0136, 0223, 0190, 0114, 0362, 0225, 0652, 0637, 0482 0543, 0038, 0244, 0036, 0291 0221, 0543, 0317, 0190 0129, 0543 0064, 0036, 0244, 0583, 0099, 0317, 0397, 0291, 0546, 0235, 0243, 0614, 0645, 0671 0244, 0235, 0063, 0072, 0366, 0244, 0397, 0038, 0099, 0243, 0131, 0135 0064, 0039, 0421, 0546, 0274, 0245, 0286, 0398, 0244, 0583, 0233, 0286, 0438, 0245 0637, 0243, 0482 0120, 0063, 1220, 0321, 0321 0114, 0129, 0543 0354, 0222, 0227, 0063 0114, 0129 0037, 0129, 0114, 0543, 0321, 0233 0099, 0190 0397, 0235, 0366 0064, 0036, 0309 0190, 0235 0064, 0036, 0321, 0397 0038, 0037, 0063, 1532, 1678, 0129 0129, 0401 0445, 0036, 0064, 0244, 0245, 0401 0245, 0309
Stern Strato Stylandia Sunkai Sunstar Sunwood SuperTech Superla Supra Susumu Sysline Sytong T+A TVTEXT 95 Tandberg Tandy Tashiko Tatung Tec Technics Teleavia Telefunken Telegazi Telemeister Telesonic Telestar Teletech Teleton Televideon Temco Tennessee Tensai Texet Thomson Thorn Tokai Tomashi Toshiba Trans Continens Trident
0233, 0286, 0190, 0291, 0438 0064, 0637, 0321, 0382, 0482 0064, 0036, 0036, 0064, 0394 0190, 0245, 0099, 0244, 0120 0244, 0063, 0190, 0243 0543, 0099, 0064, 0244, 0038 0244, 0286, 0274, 0364, 0223 0128, 0136, 0289, 0362, 0652, 0064, 0101, 0223, 0064, 0606 0064, 0036, 0364 0233, 0063, 0244, 0398, 0401, 0064, 0036, 0244, 0131, 0321, 0404, 0132, 0245, 0274 0243, 0036, 0245, 0401 0136, 0223, 0362, 0225, 0652, 0064 0265, 0064, 0101, 0131, 0362, 0099, 0401, 0539 0190, 0064, 0364, 0535, 0063, 0097, 0129, 0136, 0543 S E T U P C O D E 39

0027, 0267, 0064, 0108, 0075 0027, 0108, 0075, 0068, 0070 0068, 0027 0047, 0099, 0253 0068, 0520 0068, 0347, 0348, 0520, 0411, 0521, 0099 0099, 0031, 0027 0068, 0347, 0348, 0411, 0521, 0305, 0555, 0094, 0520 0064, 0068, 0072, 0068, 0411, 0070, 0267 0108, 0027, 0375, 0064, 0133, 0267, 0222, 0072 0075, 0027, 0099, 0267, 0047 0061, 0060, 0027
INSTELCODES VOOR DIGITAL VIDEO DISC SETUP CODES FOR DIGITAL VIDEO DISC Akai Bush Cyber Home Denon DiViDo Grundig JMB JVC Kenwood LG Lecson Magnavox Oritron Panasonic Philips Pionee Proline Samsung Sharp Sony Technics Thomson Toshiba Universum Wesder Wharfedale Yamakawa Zenith 0722 0650, 0585 0517, 0566, 0530 0552, 0530

S E T U P C O D E 43

DSR 2210 - 5143 2