ENGLISH 4 BAHASA MELAYU 13 BAHASA INDONESIA 22 TING VIT 62

HQ7415

ENGLISH

Important

Read these instructions for use carefully before using the appliance and save them for future reference. Only use the powerplug supplied to connect the appliance to the mains. The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts. Only use the powerplug that comes with the appliance to guarantee safe transformation. The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. Store and use the appliance at a temperature between 5cC and 35cC. Make sure the powerplug does not get wet. Always unplug the shaver before cleaning it under the tap. The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

Using the appliance

Put the appliance plug in the shaver. Put the powerplug in the wall socket.

Shaving

1 Switch the shaver on by pressing the on/off button once.
Move the shaving heads quickly over your skin, making both straight and circular movements. Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philishave system. 3 Switch the shaver off by pressing the on/off button once. Put the protection cap on the shaver every time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.
Open the trimmer by pushing the slide upwards.
The trimmer can be activated while the motor is running.

Cleaning and maintenance

Regular cleaning guarantees better shaving performance. The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the appliance. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.
C For easy and optimal cleaning, the Philishave Action Clean (shaving head cleaner, type
HQ100) is available.Ask your Philishave dealer for information. The Philishave Action Clean may not be available in all countries. Contact the Customer Care Centre in your country about the availability of this accessory.
You can also clean the shaver in the following way:

Every day: shaving unit

When you clean the appliance, it is not necessary to take the shaving heads (cutters and guards)
apart. If you want to take them apart, be sure not to mix up the cutters and guards, since grinding of the cutters in the guards only guarantees optimal performance for each matching set. If you accidentally mix up the sets, it could take several weeks before optimal shaving performance is restored. 1
Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2). Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time.
Close the shaving unit and shake off excess water. Never dry the shaving unit with a towel or tissue as this may damage the shaving heads.
Open the shaving unit again and leave it open to let the appliance dry completely. You can also clean the hair chamber without water by using the brush supplied.

Trimmer

Clean the trimmer every time you have used it. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Clean the trimmer with the brush supplied. Lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Storage

Put the protection cap on the shaver to prevent damage. The appliance can be stored in the pouch supplied.

Replacement

Replace the shaving heads every 2 years for optimal shaving results. Replace damaged or worn shaving heads with HQ6 Philishave Quadra shaving heads only.
Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2). Turn the wheel anticlockwise (1) and remove the retaining frame (2).
Remove the shaving heads and place new ones in the shaving unit in such a way that the parts with the small holes point towards the centre of the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2).

Accessories

The following accessories are available: - HQ8000 powerplug. - HQ6 Philishave Quadra shaving heads. - HQ100 Philishave Action Clean (shaving head cleaner). - HQ101 Philishave Action Clean refill (shaving head cleaning liquid).
- HQ110 Philishave shaving head cleaner (shaving head cleaning spray).

Guarantee & service

If you need information or if you have a problem, please visit the Philips Web site at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

Troubleshooting

Reduced shaving performance
Cause 1: the shaving heads are dirty.The shaver has not been rinsed long enough or the water used was not hot enough.
Clean the shaver thoroughly before you continue shaving (see chapter 'Cleaning and maintenance').
Cause 2: long hairs are obstructing the shaving heads.
the retaining frame from the shaving C Removeturning the wheel anticlockwise. unit by Remove the shaving heads from the shaving unit.
C Remove the hairs from the cutters and guards with the brush supplied.
Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. Put the shaving heads back into the shaving unit. Put the retaining frame back into the shaving unit, press the wheel and turn it clockwise.

(1) (2)
: HQ8000 HQ6 Philishave Quadra HQ100 Philishave Action Clean () HQ101 Philishave Action Clean refill () Philishave HQ110 ()
www.philips.com ( ) Philips Domestic Appliance and Personal Care BV

( '' )

() HQ6 Philishave Quadra

Philips

2003/11/26

c c

ENGLISH 4 DEUTSCH 13 FRANAIS 22 NEDERLANDS 31 ESPAOL 40 ITALIANO 49 PORTUGUS 58 TRKE 67

HQ7415, HQ7405

ENGLISH

Important

Read these instructions for use carefully before using the appliance and save them for future reference. Only use the powerplug supplied. The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts. The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. Do not use a damaged powerplug. If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. Make sure the powerplug does not get wet. Store and use the appliance at a temperature between 5cC and 35cC. The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. Always unplug the shaver before cleaning it under the tap.
Using the appliance Shaving
Put the appliance plug in the shaver. Put the powerplug in the wall socket. Switch the shaver on by pressing the on/off button once.
Move the shaving heads quickly over your skin, making both straight and circular movements. Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philips system. 5 Switch the shaver off by pressing the on/off button once. Put the protection cap on the shaver every time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.
Open the trimmer by pushing the slide upwards. The trimmer can be activated while the motor is running.

Cleaning and maintenance

Regular cleaning guarantees better shaving performance. The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the shaver. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt. the Philips C For extra thorough cleaning,cleaner, type Action Clean (shaving head
HQ100) is available.Ask your Philips dealer for information. The Philips Action Clean may not be available in all countries. Contact the Customer Care Centre in your country about the availability of this accessory.
You can also clean the shaver in the following way:
Every day: shaving unit and hair chamber
1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2).
Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time.
Close the shaving unit and shake off excess water. Never dry the shaving unit with a towel or tissue as this may damage the shaving heads.
Open the shaving unit again and leave it open to let the appliance dry completely. You can also clean the hair chamber without water by using the brush supplied.
Every six months: shaving heads
Open the shaving unit, turn the wheel anticlockwise (1) and remove the retaining frame (2).
Clean the cutters and guards with the brush supplied. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored.

3 Put the shaving heads back into the shaving unit. Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2) (also see chapter 'Replacement'). Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Clean the trimmer with the brush supplied. Lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Storage

C Put the protection cap on the shaver to prevent damage.
The appliance can be stored in the pouch supplied (HQ7415 only).

Replacement

Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ6 Philips Quadra shaving heads only. 1
Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2). Turn the wheel anticlockwise (1) and remove the retaining frame (2).
Remove the shaving heads and place new ones in the shaving unit in such a way that the parts with the small holes point towards the centre of the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2). Close the shaving unit.

Accessories

The following accessories are available: - HQ8000 powerplug. - HQ6 Philips Quadra shaving heads. - HQ100 Philips Action Clean (shaving head cleaner). - HQ101 Philips Action Clean refill (shaving head cleaning liquid). - HQ110 Philips shaving head cleaner (shaving head cleaning spray).

Environment

throw the away with the C Do not household appliancethe end of its life, normal waste at but hand it in at an official collection point for recycling. By doing this you will help to preserve the environment.

Guarantee & service

If you need information or if you have a problem, please visit the Philips Web site at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

Troubleshooting

1 Reduced shaving performance Cause 1: the shaving heads are dirty. B The shaver has not been rinsed long enough or the water used was not hot enough. Clean the shaver thoroughly before you continue shaving (see chapter 'Cleaning and maintenance').
Cause 2: long hairs are obstructing the shaving heads. Clean the cutters and guards with the brush supplied. See chapter 'Cleaning and maintenance', section 'Every six months: shaving heads'. Cause 3: the shaving heads are damaged or worn. Replace the shaving heads. See chapter 'Replacement'. 2