ENGLISH 4 BAHASA MELAYU 18 BAHASA INDONESIA 32 TING VIT 96

HQ8885

ENGLISH

Important

Read these instructions for use carefully before using the appliance and save them for future reference. Only use the powerplug supplied. The powerplug transforms 100-240 volts to a safe low voltage of less than 24 volts. The powerplug contains a transformer. Do not cut off the powerplug to replace it with another plug, as this will cause a hazardous situation. Do not use a damaged powerplug. If the powerplug is damaged, always have it replaced by one of the original type in order to avoid a hazard. Charge, store and use the appliance at a temperature between 5cC and 35cC. Do not recharge the shaver in a closed pouch. Make sure the powerplug does not get wet. Always unplug the shaver before cleaning it under the tap. The appliance complies with the internationally approved IEC safety regulations and can be safely cleaned under the tap. Be careful with hot water. Always check if the water is not too hot, to prevent your hands from getting burnt.

The display

The display provides the following information:

Charging

you connect the appliance to the C As soon asdisplay lights up, the plug symbol mains, the appears and the minute indication starts blinking.

Batteries fully charged

as C As soon thethe batteries have been fully charged, word 'FULL' runs across the display and the display light starts blinking.

Remaining shaving time

C The number on the display indicates the remaining shaving time in minutes.The black
segments indicate how much energy there is still left in the batteries.The shaving time of a fully charged shaver can range from 35 to 45 minutes, depending on your type of beard and your shaving behaviour, and is calculated by the built-in computer. During the first few charges, the shaving time indicated is a conservative estimate, which will be adjusted automatically to the actual shaving time once the shaver has determined your shaving behaviour.

Cleaning reminder

that the shaver is to be C To remind you will be about oncedueweek in cleaned, which a case of normal use, the tap symbol with blinking water drops appears on the display.

Batteries running low

shaver C When you switch thelow, theoff while the batteries are running plug symbol starts blinking and you will hear a few beeps. When you switch the shaver on or off, the display lights up for approx. 10 seconds.

Demonstration program

The appliance has a unique 1-minute demonstration program. Press the on/off button a few seconds until all symbols appear on the display. During the demonstration, the appliance will automatically be switched on three times.You can interrupt the demonstration by pressing the on/off button.
Make sure the appliance is switched off before you start charging it. When you charge the shaver for the first time or after a long period of disuse, let it charge continuously for 4 hours. Charging normally takes approx. 1 hour.
You can also shave without charging by connecting the shaver to the mains. Do not leave the appliance connected to the mains for more than 24 hours.

Charging the appliance

Charge the appliance when the plug symbol starts blinking and you hear a few beeps. Do not recharge the shaver in a closed pouch.
Put the appliance plug in the shaver. Put the powerplug in the wall socket. Remove the powerplug from the wall socket and pull the appliance plug out of the shaver when the batteries have been fully charged.

Cordless shaving time

A fully charged shaver has a cordless shaving time of up to 45 minutes.
Using the appliance Personal Comfort Control
Personal Comfort C The to adapt the shaverControl system allows you to your skin type. - You can set the shaver to 'Normal' for a fast and comfortable close shave. - You can set the shaver to 'Sensitive' for a comfortable close shave with optimal skin comfort.
C The position is the neutral position. C The 'S' position is best suited for sensitive skin.

C The 'N' position is best suited for normal skin.

Shaving

1 Switch the shaver on by pressing the on/off button once.
Move the shaving heads quickly over your skin, making both straight and circular movements. Shaving on a dry face gives the best results. Your skin may need 2 or 3 weeks to get accustomed to the Philishave system. 3 Switch the shaver off by pressing the on/off button once. Put the protection cap on the shaver every time you have used it, to prevent damage.

Trimming

For grooming sideburns and moustache.
Open the trimmer by pushing the slide upwards. The trimmer can be activated while the motor is running.

Cleaning and maintenance

Regular cleaning guarantees better shaving performance. The easiest and most hygienic way to clean the appliance is to rinse the shaving unit and the hair chamber with hot water every time you have used the appliance. Be careful with hot water. Always check if the water is not too hot to prevent your hands from getting burnt.
the Philishave C For extra thorough cleaning,cleaner, type Action Clean (shaving head
HQ100) is available.Ask your Philishave dealer for information. The Philishave Action Clean may not be available in all countries. Contact the Customer Care Centre in your country about the availability of this accessory.
You can also clean the shaver in the following way:
Every day: shaving unit and hair chamber
1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Press the release button (1) and open the shaving unit (2).
Clean the shaving unit and the hair chamber by rinsing them under a hot tap for some time. Make sure the inside of the shaving unit and the hair chamber have been cleaned properly. Rinse the outside of the appliance. Close the shaving unit and shake off excess water.
Never dry the shaving unit with a towel or tissue as this may damage the shaving heads.
Open the shaving unit again and leave it open to let the appliance dry completely. You can also clean the hair chamber without water by using the brush supplied.
Every six months: shaving heads
Open the shaving unit, turn the wheel anticlockwise (1) and remove the retaining frame (2).
Clean the cutters and guards with the brush supplied. Do not clean more than one cutter and guard at a time, since they are all matching sets. If you accidentally mix up the cutters and guards, it may take several weeks before optimal shaving performance is restored. 3 Put the shaving heads back into the shaving unit. Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2). Close the shaving unit.

Trimmer

Clean the trimmer every time you have used it. 1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver.
Clean the trimmer with the brush supplied.
Lubricate the trimmer teeth with a drop of sewing machine oil every six months.

Storage

C Put the protection cap on the shaver to prevent damage.
the appliance in the luxury C Store the appliance in the stand topouch or place dry.

Replacement

Replace the shaving heads every two years for optimal shaving results. Replace damaged or worn shaving heads with HQ8 Philishave Sensotec shaving heads only.
1 Switch the shaver off, remove the powerplug from the wall socket and pull the appliance plug out of the shaver.
Press the release button (1) and open the shaving unit (2). Turn the wheel anticlockwise (1) and remove the retaining frame (2).
Remove the shaving heads and place new ones in the shaving unit in such a way that the parts with the small holes point towards the centre of the shaving unit. Make sure that the projections of the shaving heads fit exactly into the recesses. 5 Put the retaining frame back into the shaving unit, press the wheel (1) and turn it clockwise (2). Close the shaving unit.

Accessories

The following accessories are available: - HQ8000 powerplug. - HQ8 Philishave Sensotec shaving heads. - HQ100 Philishave Action Clean (shaving head cleaner).
- HQ101 Philishave Action Clean refill (shaving head cleaning liquid). - HQ110 Philishave shaving head cleaner (shaving head cleaning spray).

Environment

The built-in rechargeable batteries contain substances that may pollute the environment.
Disposal of the batteries
Remove the batteries when you discard the appliance. Do not throw the batteries away with the normal household waste, but hand them in at an official collection point.You can also take the appliance to a Philips service centre, which will remove the batteries for you and will dispose of them in an environmentally safe way. Only remove the batteries if they are completely empty. 1 Remove the powerplug from the wall socket and pull the appliance plug out of the shaver. Let the shaver run until it stops, undo the screws and open the shaver. Remove the batteries.
Do not connect the shaver to the mains again after the batteries have been removed.

Guarantee & service

If you need information or if you have a problem, please visit the Philips Web site at www.philips.com or contact the Philips Customer Care Centre in your country (you will find its phone number in the worldwide guarantee leaflet). If there is no Customer Care Centre in your country, turn to your local Philips dealer or contact the Service Department of Philips Domestic Appliances and Personal Care BV.

Troubleshooting

Reduced shaving performance
Cause 1: the shaving heads are dirty. The shaver has not been rinsed long enough or the water used was not hot enough.
Clean the shaver thoroughly before you continue shaving. See chapter 'Cleaning and maintenance'.
Cause 2: long hairs are obstructing the shaving heads.
Clean the cutters and guards with the brush supplied. See chapter 'Cleaning and maintenance', section 'Every six months: shaving heads'.
Cause 3: the shaving heads are damaged or worn.
Replace the shaving heads. See chapter 'Replacement'. 2
The shaver does not work when the on/off button is pressed
Cause 1: the batteries are empty.
Recharge the batteries. See chapter 'Charging'.
Cause 2: the shaver is not connected to the mains.
Put the powerplug in the wall socket. 3
There is scale on the metal housing of the appliance
Cause: water stays behind on the metal parts of the appliance after cleaning.
To prevent scale deposits on the metal parts of the appliance, wipe the shaver dry with a towel or tissue after rinsing. Never wipe the shaving unit with a towel or a tissue, as this could damage the shaving heads. If the scale proves to be persistent, it can easily be removed by using some descaler. Rub some descaler onto the metal parts, leave it to do its work and wipe the metal parts dry. 4 The shaving unit has come off the shaver.
Cause: the shaving unit has not been placed correctly.
If the shaving unit becomes detached from the shaver, check whether the hinge spring is still properly attached, i.e. has not come loose and does not show any cracks or damage. If the hinge spring is still properly attached, the shaving unit can be easily put back on the shaver again. However, if the hinge spring has come loose, is cracked or damaged, please contact your Philips dealer or the nearest Philips service centre to avoid damage to your shaver.

BAHASA MELAYU

Penting
Baca arahan penggunaan ini dengan teliti sebelum menggunakan peralatan dan simpan untuk rujukan di masa depan. Gunakan hanya plag kuasa yang dibekalkan. Plag kuasa mengubah 100-240 volt kepada voltan rendah dan selamat tidak melebihi 24 volt. Plag kuasa mengandungi sebuah transformer. Jangan potong plag kuasa untuk menggantikannya dengan plag yang lain kerana ini akan menimbulkan situasi berbahaya. Jangan gunakan plag kuasa yang rosak. Jika plag kuasa rosak, gantikan dengan pengganti jenis tulen untuk mengelakkan daripada kemudaratan. Cas, simpan dan gunakan peralatan pada suhu di antara 5cC dan 35cC. Jangan mengecas semula pencukur di dalam pau tertutup. Pastikan plag kuasa tidak kena basah. Sentiasa cabut plag daripada pencukur sebelum membersihkannya di bawah pili air. Peralatan mematuhi peraturan keselamatan antarabangsa IEC yang diluluskan dan boleh dibersihkan dengan air paip. Berhati-hati dengan air panas. Sentiasa periksa agar air tidak begitu panas, untuk mengelakkan tangan anda daripada kelecuran.

Philips Shaving heads

Dual Precision heads

3 shaving heads

Keep a close shave

Change heads every 12 months for best results
Every year, your blades travel the height of Mt. Everest. 49 times! After such a workout, even the best materials can lose their edge. Retain your shaver's peak performance - Replace the heads once every 12 months.
Comfortably close Super Lift & Cut shaving technology with dual blade system Shaves even the shortest stubble Precision Cutting System Smooth skin contact Comfort shaving heads

Shaving heads

HQ8/42
Dual Precision heads 3 shaving heads

Specifications

Shaving heads per packaging: 3 Fits product types: HQ7100, HQ7140, HQ7160, HQ7180, HQ7200, HQ7240, HQ7290, HQ8445, HQ8830, HQ8850, HQ8870, HQ8880, HQ8882, HQ8890, HQ8894, HQ7300, HQ7320, HQ7340, HQ7360, HQ7380, HQ7390, 7110X, 7115X, 7125X, 7140XL, 7145XL, 7150X, 7180XL, 7183XL, 7240XL, 7260XL, 7310XL, 7315XL, 7325XL, 7340XL, 7345XL, 7350XL, 7360XL, 7380XL, 7800XL, 7810XL, 8831XL, 8845XL, 8846XL,

Highlights

8867XL, 8881XL, 8892XL, 8894XL, HQ5715, HQ6070, HQ6073, HQ6090, HQ6095, HQ7120, HQ7141, HQ7142, HQ7143, HQ7165, HQ7260, HQ7310, HQ7350, HQ7800, HQ8825, HQ8845, HQ8865, HQ8875, HQ8885, HQ8893, HQ6075, 8825XL, 8865XL, 8880XL, 8883XL, 8890XL, 8891XL, HQ7110, HQ7115, HQ7125, HQ7130, HQ7145, HQ7150, HQ7159, HQ7183, HQ7190, HQ7241, HQ7250, HQ7280, HQ8831, HQ8846, HQ8867, HQ8881, HQ8883, HQ8891, HQ8892, HQ8895
Super Lift & Cut technology
Dual blade system: first blade lifts, second blade cuts for a comfortable close shave.

Precision Cutting System

Ultra thin heads with slots to shave long hairs and holes to shave the shortest stubble.

Comfort shaving heads

The skin friendly profile enables smooth skin contact for a comfortable shave.
Issue date 2011-03-30 Version: 3.0.1
2011 Koninklijke Philips Electronics N.V. All Rights reserved. Specifications are subject to change without notice. Trademarks are the property of Koninklijke Philips Electronics N.V. or their respective owners. www.philips.com

12 NC: 00000