Universal

Your Remote Control Votre Tlcommande Ihre Fernbedienung Uw afstandsbediening Din fjrrkontroll Kauko-ohjaimesi Din fjernbetjening Din fjernkontroll

Instructions for use

You just made a great choice by buying this Philips universal remote control! It can operate the most-used functions of almost any brand of TV.

English

Installing the batteries
Your SBC RU 510 needs two 1.5V batteries, type R03, UM4 or AAA. Put them in like this:
Remember to replace the batteries at least once a year. Dont leave the batteries out for longer than one hour, otherwise you will need to set-up the SBC RU510 again.

KEYS & FUNCTIONS

Power: to switch TV on and off. Mute: to switch the TV sound on and off.

PROG VOL

Channel Up/Down: to select next / previous channel. Volume Up/Down: to control the TV volume.
Number Keys: for direct channel selection and other functions.
To switch between one and two-digit channel selection and display. SHIFT: to get access to additional functions (press together with other function keys). Depending on the age of your equipment, the result is for example: SHIFT + PROG+: increases brightness or menu up function SHIFT + PROG-: decreases brightness or menu down function SHIFT + VOL+: increases colour or menu right function SHIFT + VOL-: decreases colour or menu left function To operate menu control. To confirm your selection. Try other shift/key combinations on your TV to discover which functions are available. Remember that you cant get access to additional functions if these functions were not available on the original remote control of your TV! 2
To switch on teletext. English 3 To enlarge the teletext display on screen. To stop changing teletext pages. To switch off teletext. If you use the memory out key () to access the next teletext page on your Philips TV, see Troubleshooting. Fasttext

Red Green Yellow Blue

SET-UP FOR USE

D V I C E

Carefully read the complete procedure before starting!
Your TV is a Philips brand: 1 Press the power key to test.
The green LED lights up to confirm transmission.

H E C K

Press a few keys to check correct response. If response is not correct, go to the next paragraph.
Your TV is of another brand, or your TV is a Philips brand, but not all keys respond correctly: 1 Look up the brand name of the TV you want to operate in
the code list (centre of this manual).
2 Make sure the TV is switched on. 3 Press and hold keys 1 and 3 simultaneously - for about
three seconds- until the green LED lights up. (Release the keys: the green LED should stay on) 4 Enter your 4-digit code using the number keys, within 30 seconds. The green LED flashes twice.
Thats it! Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1, using the next 4-digit code in the codelist.
- If the LED displays one long flash, the code was not recognised. Please go back to step 1 and repeat the procedure, using the next 4-digit code in the list. - If no key is pressed within 30 seconds, you have to start again at step 1. - If no correct code is in the list, go to the next paragraph.
You do not know the brand of your TV/you can not find the right code in the code list auto search: 1 Make sure the TV is switched on. 2 Press and hold keys 1 and 3 simultaneously -for about
three seconds- until the green LED lights up. (Release the keys: the green LED should stay on) 3 Press the power key to start the search. Make sure that you keep the remote control pointed at your TV. Each time the green LED flashes, another code is sent. When the right code is found, the TV switches off. Immediately press the power key to stop the search. If the green LED flashed again after the TV switched off, this means you missed the correct code! If you missed the code, follow the next procedure, starting at step 4. If the LED did not flash again after the TV switched off, go to step 6.
4 Switch the TV manually back on. 5 Press PROG- (down only!) repeatedly to send previous
codes until the TV switches off again.
6 Press the power key to lock the correct code in the SBC
RU510s memory. The green LED flashes twice.
Switch TV on manually. Press a few keys to check correct response. If response is not correct, repeat procedure beginning at step 1.
- The search time averages about 90 seconds. (Maximum search time is 5 minutes for TV). - Autosearch stops automatically after all codes have been tested.

MAKE A NOTE OF YOUR CODE!
Carefully read the complete procedure before starting! Note the code inside the battery case and in the codelist in the centre of this booklet. This may be useful if you ever need to set up the SBC RU510 again. You used the auto search procedure or you forgot to note the code after set up? No problem! You can still read out the code from the remote: 1 Press and release keys 1 and 6 simultaneously. Important: after pressing the keys, you have to release them immediately! The green LED lights up. 2 Press the two digits key. The green LED goes out.
3 Press key 1 and count the number of times the green LED
flashes. This is the first digit of the 4-digit code. (No flashes means the digit is zero.) 4 Press key 2 and count the number of flashes for the second digit. 5 Press key 3 and count the number of flashes for the third digit. 6 Press key 4 and count the number of flashes for the forth digit. 7 Note the code. English
Add a specific function to your remote control
In case you do not find the function you want to use (e.g. a specific teletext function), it can easily be added to your remote controls functionality. All you have to do is contact the Philips Universal Remote Control helpline to obtain the 3-digit code for the missing function. The rest of the procedure is quite simple: 1 Press and hold keys 1 and 6 simultaneously - for about three seconds - until the green LED lights up. 2 Enter 9, 9 and 4, using the number keys. 3 Enter the 3-digit code you received from the helpline using the number keys, within 30 seconds. 4 Press the key under which you want to store the new function. The LED flashes twice to indicate a succesfull installation. If you want to store the function under a Shift/Key combination; first press Shift, then press the required function key.
- The original function of the key will be overwritten. If you want to return to its original function see the following section about resetting. - Remember: no functions can be performed by this remote control that are not present on the equipment you are operating!
Reset your remote control to its original presets:
If you want to return to the original functions of all keys and delete all added functions under programmed keys a simple reset procedure is sufficient: 1 Press and hold keys 1 and 6 simultaneously - for about three seconds - until the green LED lights up. 2 Enter 9, 8 and 1, using the number keys. - The LED flashes twice to indicate a succesfull reset. The keys on your remote control will now perform their default functions.
Instructions for use TROUBLESHOOTING GUIDE
Problem: Solution: Device is not responding and the green light does not flash when you press a button. Replace batteries with two new 1.5 volt, type RO3, UM4 or AAA batteries. Device is not responding, but the green light does flash when you press a button. Aim the SBC RU510 at the TV and be sure that there are no obstructions between the SBC RU510 and the TV. The SBC RU510 is not performing commands properly. You may be using the wrong code. Try repeating Set up using another code, listed under your brand, or start the Autosearch Set-up over again to locate the proper code. If the TV still doesnt respond, call the help-line and well put you back on track. You cant access teletext pages and you were used to use this () button to access teletext. Follow Set up procedure and at step 5 of section Your equipment is of another brand, or your equipment is a Philips brand, but not all keys respond correctly press keys 0, 0, 6 and 4. To enter teletext pages, press the teletext cancel button. The teletext buttons do not work. Be sure your TV has teletext capabilities. The SBC RU510 does not extend the capabilities of your TV! Having problems operating all the functions on your TV. The SBC RU510 may just need customising for your model type. Just call our help-line and well put you back on track. Your brand is not listed in the code list. Try the hands-free Autosearch method. You want to reset the remote control to its factory preset. 1 Press and hold keys 1 and 6 simultaneously - for about 3 seconds - until the green LED lights up. 2 On the keypad, press keys 9, 8, and 1. The LED flashes twice to indicate a successful reset. English

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 1

Universal

Instructions for use English 4 Instruzioni per l'uso Italiano 11 Instrucciones de manejo Espaol 18 Manual de utilizao Portugees 25

SBC RU 510/87U

32 40 Nvod k pouit esky 47 Instrukcja obsugi Polski 54
XP SBC RU 520/00.3 06-02-2004 14:09 Pagina 2
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 3

U N I V E R S A L

S B C RU 0 U
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 4
Instructions for use Contents
1. 2. Introduction. 4 Installing the remote control. 5-7 Inserting the batteries. 5 Testing the remote control. 5 Setting the remote control. 6 Automatically setting the remote control. 7 Keys and functions. 8 Extra possibilities. 9 Adding a function to the remote control. 9 Restoring the original functions of your remote control. 9 Troubleshooting. 10 Need help?. 10 Code list of all brands / equipment. 61-67 English 4

1. Introduction

Congratulations on your purchase of the Philips SBC RU510 universal remote control. After installing the remote control it can operate the most-used functions of almost any brand of TV. You can find information about how to prepare this remote control for use in the chapter Installing the remote control.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 5
Instructions for use 2. Installing the remote control Inserting the batteries 1 Press the cover inwards and slide it in 2 3
the direction of the arrow. Place two R03, UM4 or AAA type batteries into the battery compartment, as shown. Slide the cover back and click it firmly into place. English

VOL VOL

Testing the remote control
The remote control has been programmed to operate the most-used functions of almost any brand of TV. Because the RU510 may use different signals for each make and even for different models of the same make, it is advisable to test whether your TV responds to the RU510. The example below instructs you how to do this.
Turn your TV on manually or use the original remote control. Tune to channel 1. Check whether all the keys are working. For an overview of the keys and their functions see 3. Keys and functions. If the TV responds as it should to all of the key commands the RU510 is ready for use.
If the TV does not respond at all or not to all of the key commands, follow the instructions under Setting the remote control.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 6
Instructions for use Setting the remote control
This is only necessary if your TV does not respond to the RU510. If that is the case, the RU510 does not recognize the brand and/or model of your TV and you need to program the remote control to do so. The example belowinstructs you how to do this. English 6
Turn on the TV manually or use the original remote control. Tune in to channel 1. Look up the brand of your TV in the code list at the back of this manual. One or more four-figure codes are shown for each brand. Note the first code. Keep keys 1 and 3 pressed simultaneously for three seconds until the green LED 3 flashes twice and then remains lit

Then enter the code noted in step 2 using the digital keys. The green LED will now flash twice. If the LED flashes once for an extended period, the code has not been entered properly or the wrong code has been entered. Start again from step 2. Point the RU510 at the TV and check that it responds as it should. If the TV responds to all of the key commands, the RU510 is ready for use. Do not forget to note your code. If the TV does not respond at all, or not to all of the key commands, start again from step 2 and try the next code from the list.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 7

Instructions for use

If you cannot find the right code for your brand device, the remote control can automatically search for the right code. English
Automatically setting the remote control
Make sure the TV is switched on and select a channel using the original remote control or the keys on the TV (for example channel 1). The RU510 emits the switch off TV signal for all models of TV that are stored in the memory. Then keep keys 1 and 3 on the RU510 pressed simultaneously for three seconds, 3 until the green LED flashes twice and then remains lit. 6
Press the Standby key of the RU510 briefly.
The RU510 now starts emitting all known TV off signals, one by one. Each time a code is sent, the green LED lights up
When your TV switches off (stand-by), you press the Standby key of the RU510 twice within 1 second, to confirm.
The RU510 has now found a code that works on your TV. Check if you can operate all functions on your TV with the RU510. If this is not the case, you can redo the automatic setting. The RU510 will then search for a code that perhaps works better. After the RU510 has run through all the known codes, the search will stop automatically and the green LED will stop flashing. Automatic programming of a TV takes a maximum of 5 minutes.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 8
Instructions for use 3. Keys and functions
The illustration on page 3 gives an overview of all keys and their functions. 1 y Standby. switches the TV on or off. 2 s. mutes the sound of the TV. 3 - VOL +. adjusts the TV volume. 4 MENU. turns the menu on and off. 5 Digital keys. direct choice of channels and other functions. 6 SHIFT. for extra functions. When pressed at the same time as a second key, the second key will get another function. For example: SHIFT + PROG+:. 'menu up' SHIFT + PROG-:. 'menu down' SHIFT + VOL+:. 'menu right' SHIFT + VOL-:. 'menu left' Tr y out other combinations with the Shift-key on your appliance in order to find out which functions are available. Only functions featured on the original remote control are available. 7 /. selects between one- and two-figure channel numbers. 8 OK. confirms your selection. 9 - PROG +. selects a previous or following channel. 0 AV. switches between external inputs of your equipment. !. teletext keys If you use the () 'memory off' key to get to the next teletext page on your Philips TV, you can press the OK key for this. See also Troubleshooting. If the device does not respond at all, or not to all of the key commands, follow the instructions under Setting the remote control. It is possible that you must enter another code for the device. English 8

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 9

English 9

4. Extra possibilities Adding a function to the remote control
If you want to add a function to the RU510, you can contact the Philips service line for Universal Remote Control to ask for the 3-figure code for the extra function.
Keep 1 and 6 on the RU510 pressed. simultaneously for three seconds, until the green LED flashes twice and then remains lit.
Press keys 9, 9 and 4, in that order.
Enter the 3-figure code which you received from the service line within thirty seconds. Press the key under which you want to store the new function. The LED flashes twice. The extra function has been successfully added to the RU510. If you want to store the function under Shift in combination with another key, first press the Shift key and then press the required function key. For restoring the original function of the key, see Restoring the original functions of your remote control.
Restoring the original functions of your remote control 1 Keep keys 1 and 6 on the RU510
pressed simultaneously for three seconds, until the green light flashes twice and then remains lit.
Press keys 9, 8 and 1, in that order. The light flashes twice. All original functions have now been restored and any extra functions have been deleted.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 10
Instructions for use 5. Troubleshooting
Problem Solution The TV does not respond and the green LED does not flash when you press a key. Replace the old batteries with two new 1.5 Volt, RO3, UM4 or AAA batteries. The TV does not respond but the green LED does flash when a key is pressed. Point the RU510 at the device and make sure that there are no obstructions between the RU510 and the device. The RU510 does not respond properly to commands. Maybe you are using the wrong code. Try programming the RU510 again using another code, which is mentioned under the brand of your device, or reset for automatic search to find the right code. If the TV still does not respond, call our helpline. You cannot get the Teletext pages on your screen, while you are used to use the () button for this. Follow the instructions under Setting the remote control and at step 4 press keys 0, 0, 6 and 4. Press the OK key to get Teletext pages on your screen. The Teletext keys do not work. Find out whether your TV is equipped with Teletext. You cannot switch off Teletext. Press the key for subtitling ( ) to switch off Teletext. You have difficulties operating all of the functions on your device. Maybe the RU510 has to be adapted to the model of the device. Call our helpline for details. Your brand of device is not in the code list. Try to set the RU510 automatically. See Automatically setting the remote control. None of the codes works during manual setting of the remote control. If that is the case, follow the instructions under Automatically setting the remote control. English 10

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 32
. 32. 33-35. 33. 33. 34. 35. 36. 37. 37. 37. 38 ;. 39 /. 61-67

SBC RU510 Philips.

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 33

R03, UM4 , AAA.

p p. , RU510. p RU510 ,

. , 3. , RU510.

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 34

RU510. /

RU510.

. 1. p 1 p p p , 3 p

S p p

p p RU510. , RU510

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 35

( RU510. 1).

3 p p. RU510

Standby

RU510. p p p. (standby), Standby RU510 1. ,
RU510. . , RU510. RU510. 5. ,
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 36
3 y Standby s. - VOL +. MENU. p p ( p ). SHIFT. ,. : SHIFT SHIFT SHIFT SHIFT ,. 7 /. 8 OK. 9 - PROG +. 0 AV. !. teletext () ' p , . teletext p O. p off' Philips, p. + PROG+:. + PROG-:. + VOL+:. + VOL-:. ' ' ' ' ' ' ' Shift.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 37

RU510, Philips ,.

. RU510. ,. ,. Shift Shift.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 38
o o. RO3, UM4 o o RU510. RU510 ,. , o. 5 OK. o o o. o . o. ,. RU510. RU510. . Teletext. Teletext. Teletext. ( Teletext. ) 0, 0, 6 , 4. Teletext Teletext () Philips. , , RU510 RU510. AAA 1,5 Volt. ,.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 39

Philips.

RU510,. ,. , ,. Philips SBC RU510/87U: :././. ( / / ,
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 40
1. 2. . 40 . 41-43 . 41 . 41 . 42 A . 43 . 44 . 45 p . 45 p x p . 45 . 46 p . 46 p px p. 61-67
p p p p Philips SBC RU510! p p x p p p. p p p p p p. 40
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 41

2. p p p 1 p , 2 3

p p. p R03, UM4 p, p. p .
p ppp p x p p p. RU510 p p px p px p, p pp, pp p RU510. ppp p pp p.
p p . p 1. pp p x. AV x p p 3. . p p pp RU510, RU510 p.

p pp , p p .

XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 42
pp , p pp RU510. , RU510 p p p, pppp. pp p ppp pp p.
p p . p 1. p p p. p pxx. p. p p 1 3, p 3 , p.
, 2, . p . p p p, p . p p, 2. p RU510 p pp, p p pp p. p pp p , RU510 p. , p p. p pp p , p 2 p .
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 43

x , .

, p , p p p p (p., 1). RU510 x x p. p p RU510, 3 p , p. 6

pp Standby RU510.

p (p p ), Standby RU510 p 1 p. p RU510 p.
pp, p p pp RU510. , p p. RU510 p , p p. pp x x RU510 pp , p p. p p 5.
RU510 x x p. p p p p.
XP SBC RU 510/87.3 06-02-2004 12:36 Pagina 44
p. 3 x . y Standby. p. s. p. - VOL +. p p. MENU. . p . p p px. 6 SHIFT. p x. p p , . pp: SHIFT + PROG+:. 'p px ' SHIFT + PROG-:. 'p ' SHIFT + VOL+:. 'p p ' SHIFT + VOL-:. 'p ' , SHIFT, p p . p , p pp p p. 7 /. p - x p 8 OK. p p 9 - PROG +. p p . 0 AV. p . !. px p p Philips p () Memory Off, OK,. p. p pp p , p p p. , x p pp. 5