Helix Board 18 FireWire MKII
FireWire-enabled Mixing Console
IMPORTANT SAFETY INSTRUCTIONS
The apparatus shall not be exposed to dripping or splashing and that no objects with liquids, such as vases, shall be placed on the apparatus. The MAINS plug is used as the disconnect device, the disconnect device shall remain readily operable. Warning: the user shall not place this apparatus in the can be easily accessible. 1. Read these instructions before operating this apparatus. 2. Keep these instructions for future reference. 3. Heed all warnings to ensure safe operation. 4. Follow all instructions provided in this document. 5. Do not use this apparatus near water or in locations where condensation may occur. 6. Clean only with dry cloth. Do not use aerosol or liquid cleaners. Unplug this apparatus before cleaning. 7. Do not block any of the ventilation openings. Install in accordance with the manufacturers instructions. 8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including. 9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong is provided for your safety. If the provided plug does not into your outlet, consult an electrician for replacement of the obsolete outlet. 10. Protect the power cord from being walked on or pinched particularly at plug, convenience receptacles, and the point where they exit from the apparatus. 11. Only use attachments/accessories manufacturer. by the area during the operation so that the mains switch

CAUTION

RISK OF ELECTRIC SHOCK DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED PERSONNEL
The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated dangerous voltage within the product magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
WARNING: To reduce the risk of or electric shock, do not expose this apparatus to rain or moisture. CAUTION: Use of controls or adjustments or performance of procedures other than those may result in hazardous radiation exposure.
12. Use only with a cart, stand, tripod, bracket, or table by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tipover. 13. Unplug this apparatus during lighting storms or when unused for long periods of time. 14. Refer all servicing to service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Introduction..... 4. Features..... 4 Package Includes.... 4 Getting Started.... 5 Channel Setup....5. Making Connections....6 Inputs and Outputs....6 Rear Panel....7 Controls and Settings....8 Rear Panel....8 Channel Controls....8 Digital Effect Section....10 Master Section....10 FireWire Interface....13 System Requirements....13 Driver Installation....13. Channel Assignment....17 Cubase LE....17 Helix Board Control Panel....18 Digital Effects Table....20 Application....21 Specifications....23 Dimensions....25. Block Diagram....26

Phonic preserves the right to improve or alter any information within this document without prior notice. V1.0 SEP 30th,2006

Introduction

Thank you for choosing one of Phonics many quality compact mixers. The Helix Board 18 FireWire MKII mixing console - designed by the talented engineers that have created a variety of mixers fantastic in style and performance in the past - displays similar proficiency that previous Phonic products have shown; with the addition of such innovative features as FireWire interface. The Helix Board 18 FireWire MKII features full gain ranges, amazingly low distortion levels, and incredibly wide dynamic ranges - just showing the dominance these small machines will have in the mixing World. The FireWire interface of the Helix Board 18 FireWire MKII allows users to stream up to 16 individual channels to any PC or Mac, allowing for recording, editing, tweaking and deletion of all tracks at will. Then, when all your mixing is done, your final product can be burnt onto CD. You can also receive 2 input channels (or returns) from the FireWire interface to monitor your mix on your Helix Board. Also included with the Helix Board 18 FireWire MKII mixer is Steinberg Cubase LE software, giving users a taste of the operation of professional Digital Audio Workstation software by allowing users to record up to 8 tracks simultaneously. Other high performance Digital Audio Workstation software will allow upto 16 channels to be simultaneously streamed and recorded. All-in-all, the Helix Board 18 FireWire MKII will no doubt prove itself to have been a valuable investment. We know how eager you are to get started - wanting to get the mixer out and hook it all up is probably your number one priority right now - but before you do, we strongly urge you to take a look through this manual. Inside, you will find important facts and figures on the set up, use and applications of your brand new mixer. If you do happen to be one of the many people who flatly refuse to read user manuals, then we just urge you to at least glance at the Instant Setup section. After glancing at or reading through the manual (we applaud you if you do read the entire manual), please store it in a place that is easy for you to find, because chances are there is something you missed the first time around.

Features

18-input small-format analog mixer with extremely

low noise circuitry

96kHz FireWire interface for streaming 16
independent channels of audio to computer with near-zero latency FireWire interface, can be assigned to control room monitors, main mix and aux1 channels to computer from pre low cut, EQ to post EQ, post fader from main mix, group 1/2 and AUX 2/3

2 channels of monitoring from computer via Pre/post switch for swapping streaming input Channel 15/16 routed to Computer can be selected DFX, our 40-bit high definition algorithm digital
Six Mic/Line channels with inserts 8 extremely low noise mic preamps Four stereo Line channels 3-band EQ with swept mid-range 75 Hz low-cut filter on mono channels Three AUX sends, one with Pre/Post switch Two stereo AUX returns with effect to monitor level control multi-effect processor with 100 programs plus tap delay and foot switch jacks
+48V phantom power on Mic channels Solo feature on each input and output Two true subgroups with main L and R routing

switches

Built-in switching power supply with universal
connector, 100-240 VAC, 50/60 Hz Rack-mounting kit included S/PDIF digital audio output Compatible with Mac OSX and Windows XP Steinberg Cubase LE included

Package Includes

1 x Helix Board 18 FireWire MKII mixer 1 x FireWire cable 1 x CD-ROM with ASIO & WDM drivers 1 x CD-ROM with Steinberg Cubase LE 1 x Power cable 1 x Rack mounting kit If any items are missing from your package, please contact your nearest Phonic dealer

Getting Started

1. Ensure all power is turned off on your mixer. To totally ensure this, the AC cable should not be connected to the unit. 2. All faders and level controls should be set at the lowest level and all channels switched off to ensure no sound is inadvertently sent through the outputs when the device is switched on. All levels can be altered to acceptable degrees after the device is turned on. 3. Plug all necessary instruments and equipment into the devices various inputs as required. This may include line signal devices, such as keyboards and drum machines, as well as microphones and/or guitars, keyboards, etc. 4. Plug any necessary equipment into the devices various outputs. This could include amplifiers and speakers, monitors, signal processors, and/or recording devices. 5. Plug the supplied AC cable into the AC inlet on the back of the device and a power outlet of a suitable voltage. 6. Turn the power switch on. 7. Consult the FireWire section of this manual for more information on its setup and usage.

Channel Setup

1. To ensure the correct audio level of the input channel is selected, each of the Mixers Channels ON buttons should be disengaged (which should turn the corresponding LED indicator off), as well as the Solo buttons on each channel and all buttons in the Control Room Source section, with exception to the Main L/R button. 2. Ensure the channel you wish to set has a signal sent to it similar to the signal that will be sent when in common use. For example, if the channel has a microphone connected to it, then you should speak or sing at the same level the performer normally would during a performance; if a guitar is plugged into the channel, then the guitar should also be strummed as it normally would be (and so on). This ensures levels are completely accurate and avoids having to reset them later. 3. Move the Channel fader and Maser fader to around the 0 dB mark. 4. Turn the Channel ON. 5. Pushing the channels Solo button and releasing the Pre/Post button on the CTRL RM section will send the pre-fader signal of the activated channel to the Control Room / Phones mixing bus and the Level Meter will display the Control Rooms signal properties. 6. Set the gain so the level meter indicates the audio level is around 0 dB (it is advisable to never let the level exceed 7 dB). 7. This channel is now ready to be used; you can stop making the audio signal. 8. You can now repeat the same process for other channels if you wish.

Making Connections

Inputs and Outputs
1. XLR Microphone Jacks These jacks accept typical 3-pin XLR inputs for balanced and unbalanced signals. They can be used in conjunction with microphones such as professional condenser, dynamic or ribbon microphones with standard XLR male connectors, and feature low noise preamplifiers, serving for crystal clear sound replication. The Helix Board 18 FireWire MKII features a total of eight Microphone inputs.
NB. When these inputs are used with condenser microphones, the Phantom Power should be activated. However, when Phantom Power is engaged,single ended (unbalanced) microphones and instruments should not be used on the Mic inputs.
4. AUX Returns These 1/4 TS inputs are for the return of audio to the Helix Board 18 FireWire MKII mixer, processed by an external signal processor. If really needed, they can also be used as additional inputs. The feed from these inputs can be adjusted using the AUX Return controls on the face of the mixer. When connecting a monaural device to the AUX Return 1 and 2 inputs, simply plug a 1/4 phone jack into the left (mono) input, and the signal will appear in the right as well.
2. Line Inputs This input accepts typical 1/4 TRS (balanced) or TS (unbalanced) inputs, for balanced or unbalanced signals. They can be used in conjunction with a wide range of line level devices, such as keyboards, drum machines, electric guitars, and a variety of other electric instruments.
5. AUX Sends These 1/4 TRS outputs may be used to connect to an external signal processor, or even to an amplifier and speakers (depending on your desired settings) from the mixer. The signal from the AUX Sends is controlled by the AUX master controls (on the face of the mixer), which obtain their signal from the AUX controls located on each channel strip. The Helix Board 18 FireWire MKII features a total of 3 AUX Sends. When using the FireWire interface, AUX Send 1 can be elected to receive the audio signal sent from the Computer, for monitoring or recording purposes. 6. Phones This stereo output port is suited for use with headphones, allowing monitoring of the mix. The audio level of this output is controlled using the Control Room / Phones control. 7. Record Out These outputs will accommodate RCA cables, able to be fed to a variety of recording devices. Also included is a mini stereo jack for the addition of recording devices such as MD players, and even laptop computers. 8. 2T Return These RCA inputs are used to connect the mixer with parallel external devices, such as sub mixers or CD, Tape and Cassette Players. Also included are mini stereo jacks, for receiving signals from audio devices like portable CD, MD and MP3 players.
3. Stereo Channels The Helix Board 18 FireWire MKII also features a few stereo channels, thrown in for maximum flexibility. Each of these stereo channels features two 1/4 phone jacks, for the addition of various line level input devices, such as electronic keyboards, guitars and external signal processors or mixers, as well as XLR Microphone jacks on channels 7/8 and 9/10, allowing users to option of using the channel as a microphone input channel. If you wish to use a monaural device on a stereo input, simply plug the devices 1/4 phone jack into the left (mono) input and leave the right input bare. The signal will be duplicated to the right due to the miracle of jack normalizing.

9. Main Outputs These two 1/4 TRS balanced jacks will output the final stereo line level signal sent from the main mixing bus. The primary purpose of these jacks is to send the main output to external devices, which may include power amplifiers (and in-turn, a pair of speakers), other mixers, as well as a wide range of other possible signal processors (Equalizers, Crossovers, etcetera). 10. Group Outputs These balanced 1/4 TRS phone jacks output the final feed from the Group 1 and 2 mix controlled by the Group level faders. These outputs can be used to feed a wide range of devices, such as mixers, signal processors, and even to connect an amplifier and speakers to be used along with the Main Speakers, for a more rounded audio experience.
12. Control Room Outputs These two 1/4 phone jack outputs feed the signal altered by the Control Room / Phones level control on the face of the mixer. This output has extensive use, as it can be used to feed the signal from the mixer to an active monitor, for the monitoring of the audio signal from within a booth, or, alternatively, for the addition of external signal processing devices or mixers, as well as acting as a side fill output, supplying audio to indoor areas that the main speakers do not reach. When using the FireWire interface, this output can be elected to be fed the audio signal from the Computer, for monitoring of recording audio. 13. Foot Switch Jacks These ports are for the inclusion of an unlatched foot switch, used to remotely adjust properties of the builtin Digital Effect processor. The jack on the right is used to turn the Digital Effects on and off, whereas the jack on the left is used for adjusting tap delay properties.

Rear Panel

11. Channel Inserts Located on the rear of the Helix Board 18 FireWire MKII, the primary use for these TRS phone jacks is for the addition of external devices, such as dynamic processors or equalizers, to mono input channels 1 through to 6. This will require a Y cord that can send (pre-fader and pre-EQ) and receive signals to and from an external processor. The tip of the TRS plug is for sending of the signal to the external device, the ring is for return of the signal to the Helix Board 18 FireWire MKII, and the Sleeve is the grounding.
14. Main XLR Outputs These two XLR ports will output the final stereo line level signal sent from the main mixing bus. The primary purpose of these jacks is to send the main output to external devices, which may include power amplifiers (and in-turn, a pair of speakers), other mixers, as well as a wide range of other possible signal processors (equalizers, crossovers, etcetera).
Helix Board 18 FireWire MKII
19. Power Switch This switch is used to turn the mixer on and off. Ensure you turn all level controls down before activating.

Channel Controls

20. Low Cult Filter (75 Hz) This button will activate a high-pass filter that reduces all frequencies below 75 Hz at 18 dB per Octave, helping to remove any unwanted ground noise or stage rumble. On stereo channels 7/8 and 9/10, the low cut filter affects only the XLR Microphone inputs (and not the line inputs). 21. Line/Mic Gain Control This controls the sensitivity of the input signal of the Line/Microphone input. The gain should be adjusted to a level that allows the maximum use of the audio, while still maintaining the quality of the feed. This can be accomplished by adjusting it to a level that will allow the peak indicator occasionally illuminate. 22. High Frequency Control This control is used to give a shelving boost or cut of 15 dB to high frequency (12 kHz) sounds. This will adjust the amount of treble included in the audio of the channel, adding strength and crispness to sounds such as guitars, cymbals, and synthesizers. 23. Middle Frequency Control This control is used to provide a peaking style of boost and cut to the level of middle frequency sounds at a range of.15 dB. These mixers also provide a sweep control, allowing you to select a center frequency between 100 Hz and 8 kHz. Changing middle frequencies of an audio feed can be rather difficult when used in a professional audio mix, as it is usually more desirable to cut middle frequency sounds rather than boost them, soothing overly harsh vocal and instrument sounds in the audio. Stereo channels 11/12 and 13/14 of the Helix Board 18 FireWire MKII feature a High-Mid and Low-Mid control instead of the typical controls described above. They provide a peaking style of boost and cut to middle frequencies, where the frequencies are set at 3 kHz and 800 Hz (High-Mid is set at 3 kHz and Low-Mid is set at 800 Hz). Stereo channels 9/10 and 11/12 have a single Middle Frequency control, with the center frequency set at 2.5 KHz. 24. Low Frequency Control This control is used to give a shelving boost or cut of +/-15dB to low frequency (80Hz) sounds. This will adjust the amount of bass included in the audio of the channel, and bring more warmth and punch to drums and bass guitars.

25. FireWire Pre/Post Switch This switch is used to change the signal of the corresponding channel that is sent to the Computer via the FireWire interface between that of a pre-EQ, pre-fader, pre-low cut and that of a post-EQ, postfader, post-low cut. In the upper-most position, the channel will be pre, and in the lower position post. 26. AUX Controls These controls alter the signal level that is being sent to the auxiliary 1 and 2 mixes. The signals of these mixes are suitable for connecting stage monitors, allowing artists to listen to the music that is being played. Also included is a Pre/Post button, which alternates the feed to the AUX 2 mix between a post and pre-fader feed.
34. +4 / -10 Buttons These buttons, located on each stereo input channel, are used adjust the input sensitivity of the corresponding channel, which will adapt the mixer to external devices which may use different operating levels. If the input source is 10 dBV (consumer audio standard), it is best to engage the switch, allowing the signal to be heard. If the input source is +4 dBu (professional audio standard) the corresponding input channels button should be disengaged to ensure the integrity of the Mixers circuitry. If you are unsure of the sources operating level, we suggest leaving the switch disengaged until you test the sources signal. You can then engage if necessary (if the level of input is obviously too low).
38. Effect Bypass Use it to bypass the effects and monitor your audio before and after the effect is applied. When the effect engine is bypassed, the 2 small indicators on the digital effect display will flash. 39. AUX 3 / EFX Send Control and Solo Button This rotary control will adjust the level of the output signal at the AUX 3 send jack, as well as determine the amount of audio the built-in effects processor will receive. When this control is set to its minimum position, neither the AUX 3 send nor the effect processor will receive a signal. The accompanying Solo button allows the EFX Send signal to be sent to the Control Room / Phones mix. 40. To Main Control The to Main control will allow users to adjust the processed signal that is sent to the Main. 41. To AUX 1/2 Controls These controls allow users to send the signal processed by the effects processor to the AUX 1 or 2 mix, allowing for monitoring of the signal. This is called Effect to Monitor.

Digital Effect Section

35. Digital Effect Display This 2-digital numeric display shows the program number that is currently applied to your EFX audio signal. When you rotate the Program control, you can scroll through different program numbers; however the display will revert back to the original program if a new program is not selected within a few seconds. For a list of available effects, please observe the Digital Effect Table. 36. Sig and Clip Indicators Located within the Digital Effect Display are Clip and Sig LEDs. The Sig LED will light up when any signal is received by the effect processor, and the Clip LED will light up shortly before excessive signals are dynamically clipped. If the Clip LED lights up too often, it may be advisable to turn down the AUX 3/ EFX master control to ensure the signal level is not excessive. 37. Program Control This control is used to scroll through the various effects. Turning the control clockwise will allow users to ascend into higher program numbers, and turning it counter-clockwise will allow users to descend into lower program numbers. When turning to a new program, a small LED will flash until you push the program knob down this will apply the effect. When a tap-delay effect is selected, pressing this control will allow users to select the tap-delay time. By pushing the button several times, the effect processor interprets the time between last two pushes and remembers this as the delay time until the button is pushed again. This is kept even after the power is turned off. When the tap delay effect is selected, a small LED (located between the two digit display) will flash within the digital effect display window at the selected intervals.

Master Section

42. AUX Send Controls and Solo Buttons These two controls are for adjusting the audio level that is sent to the corresponding AUX outputs, the signal of which is initially taken from each channels individual AUX send controls. Pushing one of the accompanying Solo buttons will send the corresponding AUX signal to the Control Room / Phones mix (pre or post fader, depending on the Pre / Post button).
49. Level Meter This dual 12 segment level meter gives an accurate indication of when audio levels of the Main L/R output reach certain levels. The 0 dB indicator illuminates is approximately equal to an output level of +4 dBu (balanced), and the PEAK indicator illuminates just before the signal is dynamically clipped. It is suggested that users set the various levels controls so that the level sits steadily around 0 dB to make full use of audio, while still maintaining fantastic clarity. When the Solo indicator, located beside the Level Meter, is illuminated, one or more Solo buttons has been pushed. In that case, the Level meter will display properties of the Solo signal, which is helpful with setting of channel properties. If Solo indicator illuminates green, this means the Solo feed is a prefader signal. If the Solo indicator illuminates red, the feed is post-fader. If the no Solo buttons are activated, the Control Room source signal properties are displayed by the Level Meter.
43. FireWire Trim Control This is one of the newest features of the Helix Board 18 FireWire MKII. The FireWire trim control can be used to adjust the level of the outgoing FireWire signal (which will be received by the computer) from the AUX 2/3, Group 1/2 or Main L/R (depending on the FireWire Select switch). If the input signals received by your computer are noticeably excessive, using this control could help to attenuate the signal to an acceptable degree. 44. FireWire Select Switch This switch determines which of the Helix Boards signals will be used for the FireWire channels 15 and 16 sent through the FireWire interface to the computer. Users can choose to send the two channel signal from the Auxiliary 2/3, Group 1/2 or Main mixes (all prelevel controls) to the computer.
45. FireWire Assign to Buttons The Assign to Main and Assign to AUX 1 buttons allow users to determine the destination of the stereo FireWire return signal. 46. FireWire Indicator This blue LED indicator will illuminate when a connection is established through the FireWire interface. 47. +48V Indicator This indicator will illuminate when Phantom Power is activated. 48. Power Indicator The Power Indicator will light up when the power of the mixer is on.
50. Control Room Source Buttons This set of buttons allows users to select which signals they wish to send to the Control Room / Phones output. There is a button each for the FireWire, Group 1-2, 2T Return and Main mixes. These signals can be monitored simultaneously if required. 51. Control Rooms / Phones Level Control This rotary control will allow users to adjust the audio level of the Control Room / Phones signal (received by solo signal, or as chosen in the Source Select buttons). 52. Control Room Pre / Post Button The Pre / Post button alters the Solo signals received by the Control Room / Phones mix between Post and Pre fader signals. When set to Post, the Solo Indicator will light up red; when set to Pre, the Solo Indicator will light up green (channel level set).

53. 2T Return Control and To Main Button Use this rotary control to adjust the signal level received through the RCA 2T Return inputs. The To Main button allows users to send the 2T Return signal to the main mix. 54. AUX Return 1 and 2 Faders This 60mm fader adjusts the signal level of audio fed through the stereo AUX Return input. This AUX Return features L/R, GP 1/2 assign buttons, enabling users to send the audio feed to the corresponding mixing buses. Also, features a Solo button that sends the signal directly to the Control Room / Phones mix. The On button allows you to turn the AUX Return channel on and off. Activation of the AUX Return or AUX Return Solo will be accompanied by an illuminated LED. 55. AUX Return 2 to AUX 1 Control This rotary control allows users to adjust the level of audio that is sent from the AUX Return 2 signal to the AUX Send 1 mix.
56. Group 1/2 Controls These two faders are the final level control for the Group 1 and 2 audio feeds, sent to the Group 1 and 2 outputs. These faders can be fed a signal from the various mono and stereo channels, as well as EFX Returns, depending on your selections. When pushed all the way up, these faders provide 10 dB of gain to the signal, and, when set all the way down, effectively mute the signal. The Group Controls also feature Left and Right buttons, which allow you to send the Group 1/2 signal to the Main Left and Right mix. 57. Main L/R Faders These two faders are the final level control for the Main Left and Right audio feeds, sent to the Main L and R outputs. These faders are possibly fed by the various mono and stereo channels, as well as AUX and EFX returns and 2T inputs, depending on the your selections. When pushed all the way up, these faders provide 10 dB of gain to the signal, and, when set all the way down, effectively mute the signal.

FireWire Interface

System Requirements
The following are the minimum required specifications for use with the Helix Board 18 FireWire MKII mixer. If your computer does not meet these requirements, you will experience lagging of audio and possible freezing of your computer when attempting to operate the mixer.

Windows

Microsoft Windows XP SP1 and SP2 Available FireWire port (suggested FireWire Interface: ADS Pyro 64 FireWire card with TI chip) Intel Pentium 4 processor or equivalent AMD Athlon processor Motherboard with Intel or VIA chipset 5400 RPM or faster hard disk drive (7200 RPM or faster with 8 MB cache recommended) 256 MB or more of RAM (512 MB recommended)

Macintosh

OS X 10.3.5 or later with native FireWire support G4 or newer processor 256 MB or more of RAM

Driver Installation

To use the Helix Board FireWire mixer efficiently (or at all) on a PC, it is important to install all the necessary drivers from the included CD (ASIO and WDM drivers). It is important that users read all instructions carefully before continuing on to the each step of installation, as users will be required to unplug and plug in their FireWire device. This is not necessary for Mac users.
Windows XP (with Service Pack 1 or 2)
1. It is recommended that you quit all applications before starting the installation process. 2. Ensure the Helix Board FireWire is not yet connected to your Computers FireWire input. 3. Insert the installation CD included with your Helix Board FireWire mixer into the CD-ROM drive of your computer. If the CD does not automatically start the installation process within a few moments, then navigate to My Computer g your CD-ROM drive g Drivers and Control Panel g double-click setup.exe to begin the installation manually. The Helix Board FireWire Control Panel software also will be installed at this time. 4. Follow the installation instructions.
Make sure no other programs are running on your PC and that the Helix Board 18 FireWire MKII is not connected to your PC, then click Next.
Read and accept the terms of the License Agreement and click Yes to continue.
Either select a new destination for the installation, or else click Next to accept the default directory.
Click Next to begin the installation.
Connect the Helix Board 18 FireWire MKII to the Computer and turn the power on.
If a message is displayed indicating that the software has not passed Windows Logo test, click Continue Anyway.
After installation is complete, users are free to use the device as they wish.
Macintosh OS X (10.3.5 or later)
The Helix Board 18 FireWire MKII works with the primary audio drivers of Macintosh OS X 10.3.5 and later. First verify that you are running Macintosh OS X 10.3.5 or above, then connect the Helix Board 18 FireWire MKII to a FireWire port to the computer. To ensure your Helix Board 18 FireWire MKII is working, enter the Utilities folder and double-click the Audio MIDI Setup icon.

Enter the Audio Devices section. From the Properties for pull-down tab, select Helix Board 18 FireWire MKII.
At the bottom of the window, users can edit the setup of the Helix Board 18 FireWire MKII. Properties such as sampling rate and clock source can be altered. Users may also opt to make the Helix Board 18 FireWire MKII their default input and/or output device.
Mac users are able to use GarageBand Digital Audio Workstation Software, in conjunction with the Helix Board 18 FireWire MKII.

Channel Assignment

When using a Digital Audio Workstation on a PC, and within the included Phonic Helix Board 18 FireWire MKII control panel software, the following names have been attributed to the input channels of the FireWire mixer. They can be altered through the control panel software included with the mixer.
FireWire Input Channel Name Phonic HB 18 MKII CH 1 Phonic HB 18 MKII CH 2 Phonic HB 18 MKII CH 3 Phonic HB 18 MKII CH 4 Phonic HB 18 MKII CH 5 Phonic HB 18 MKII CH 6 Phonic HB 18 MKII CH 7 Phonic HB 18 MKII CH 8 Phonic HB 18 MKII CH 9 Phonic HB 18 MKII CH 10 Phonic HB 18 MKII CH 11 Phonic HB 18 MKII CH 12 Phonic HB 18 MKII CH 13 Phonic HB 18 MKII CH 14 Phonic HB 18 MKII Main L Phonic HB 18 MKII Main R Mixer Channel Channel 1 Channel 2 Channel 3 Channel 4 Channel 5 Channel 6 Channel 7 (Stereo L) Channel 8 (Stereo R) Channel 9 (Stereo L) Channel 10 (Stereo R) Channel 11 (Stereo L) Channel 12 (Stereo R) Channel 13 (Stereo L) Channel 14 (Stereo R) user definable user definable

Cubase LE

Cubase LE is a fairly powerful program provided along with the Helix Board 18 FireWire MKII mixer that allows users to record, edit, delete, and alter their tracks. Please note that only 4 tracks can be recorded at once with the version of Cubase included, and users must upgrade or find other suitable DAW software if they choose to record more tracks.

Installation

Insert the Cubase LE installation CD that came with your mixer into the CD drive of your computer. Run the installer. The serial number will be automatically entered in when installing.
After successfully completing the installation process, the following process must be followed to work efficiently with the Helix Board 18 FireWire MKII mixer. 1. Open the Cubase LE program. 2. Go to the Devices pull-down menu and select Device Setup. On the left, select VST Multitrack. 3. From the ASIO Driver drop-down list select the Phonic ASIO Driver. A pop-up box will ask you if you want to switch the ASIO driver. Click Switch. This completes the basic installation and setup. 4. Activating audio tracks received from the Helix Board mixer. a. Go to the devices pull-down menu and select VST Inputs. This will display the various inputs (Phonic HB 18 MKII Ch 1, Phonic HB 18 MKII Ch 2, etc.) b. Activate 8 of these channels by clicking the Active button located next to each channel name. Please note, only 8 input channels can be activated at any one time. This is a limitation of Cubase LE, and if more input channels are needed, we suggest upgrading to a higher version of Cubase, or use other DAW software. 5. For further instructions on the operation of Cubase, please consult the user manual by pressing F1 while the program is open. If you wish to reset the Helix Board 18 FireWire MKII ASIO driver, simply go to the devices pull-down menu and select device setup. Simply click reset and select the Phonic ASIO Driver. Click ok to continue and the Helix Board 18 FireWire MKII should once again become functional.

To alter an input channels name on your computer, open the Helix Board 18 FireWire MKII control panel software. On the left hand side of the control panel, users will find the settings categories. By clicking Input Channels, the main window will display the titles input channels. You can then highlight the channel names and press the Edit Channel Name button on the bottom of the control window. A new window will appear that will allow users to adjust the channel name. If you would like to use the Helix Board 18 FireWire MKII as your default audio output device on you PC, simply go into the Windows control panel, and select Sound and Audio Devices. Select the Audio tab, and use the pull-down menu to select the Helix Board 18 FireWire MKII from the list of available output devices. The Helix Board 18 FireWire MKII can also be selected as the default output device for individual programs by editing said programs settings / options.
Helix Board Control Panel
The Helix Board FireWire control panel can be accessed at any time by entering choosing the shortcut from your Programs menu. This program will not only allow users to alter their device and channel names and properties, but will also let them correct for latency issues, change sampling rates, and so forth. When opening the software, a number of options will be available for users to select from, allowing them to adjust the available properties.

Output Channels

By entering the Output Channels section, users can view and edit the names of the two output channels from the computer to the Helix Board 18 FireWire MKII mixer.

Devices

In the Devices section, users are able to view and edit the name of the Phonic FireWire Devices connected to their computer.

Synchronization

In the Synchronization section, users can adjust the sampling rate and other synchronization properties. Many of these adjustable properties, as they are, are set for optimum performance and, unless you are sure of what you need to change, are probably best left alone.

Input Channels

The Input Channels section allows users to view and edit the name of the various input channels received from the FireWire input. For a list of default channel names, please consult the table on page 16.
First off, the synch mode can be altered, though making this alteration is not recommended for novice users. The synch mode is basically the way the computer determines what the clock source (ie. device that your computer will use to determine the timing of all digital signals received) will be. The default setting for this feature is CSP, meaning the Helix Board 18 FireWire MKII is the master clock source of the device. The other options allow users to make the Helix Board 18 FireWire MKII follow the timing of whichever device is the clock source. Having two clock sources has the potential to create very undesireable audio, so it is best avoided. If the Helix Board 18 FireWire MKII is the only piece of digital audio equipment attached to the computer, there is no reason this option should be changed.

Application

Live Band Multitrack Recording and Monitoring

AMPLIFIER

ACTIVE MONITORS COMPRESSOR

MICROPHONES

FLOOR MONITORS

DRUM MACHINE

Studio Recording and Monitoring

Specifications

Inputs Total Channels Balanced Mono Mic / Line channel Balanced Mic / Stereo Line channel Balanced Stereo Line Channel Aux Return 2T Input Outputs Main L/R Stereo Rec Out with Trim Control CTRL RM L/R Phones Firewire Interface Channel Strips Aux Sends Pan/Balance Control Volume Controls Master Section FireWire channel 15/16 rounting switch Aux Send Masters Master Aux Send Solo Stereo Aux Returns Aux Return Assign to Subgroup Effects Return to Monitor Global AFL/PFL Solo Mode Phones Level Control Faders Metering Number of Channels Segments Phantom Power Supply Switches Effect Processor (40-bit DSP) Frequency Response (Mic input to any output) 20Hz ~ 60KHz 20Hz ~ 100KHz Channel fader down, other channels at unity +0/-1 dB +0/-3 dB <-90 dB +48V DC Master High definition algorithm 100 programs plus tap delay; foot switch jcaks (effect on/off, tap) Source from main mix, group 1/2, and aux 2/Yes Yes Aux return 1 & 2, Subgroup 1 & 2, Main L & R 2 x 1/4 TRS, Bal. & 2 x XLR Stereo RCA 2 x 1/4 TS out & 2 in, 24-bit / 96 kHz Yes 60mm fader 2 Stereo RCA
Crosstalk (1KHz @ 0dBu, 20Hz to 20KHz bandwidth, channel in to main L/R outputs)
Noise (20Hz~20KHz; measured at main output, Channels 1-4 unit gain; EQ flat; all channels on main mix; channels 1/3 as far left as possible, channels 2/4 as far right as possible. Reference=+6dBu) Master @ unity, channel fader down Master @ unity, channel fader @ unity S/N ratio, ref to +4 Microphone Preamp E.I.N. (150 gain) ohms terminated, max -86.5 dBu -84 dBu >90 dB <-129.5 dBm
THD (Any output, 1KHz @ +14dBu, 20Hz to 20KHz, chan<0.005% nel inputs) CMRR (1 KHz @ -60dBu, Gain at maximum) Maximum Level Mic Preamp Input All Other Input Balanced Output Impedance Mic Preamp Input All Other Input (except insert) RCA 2T Output All other outputs Equalization Low EQ Mid EQ (mono channel) LMid EQ (stereo channel) HMid EQ (stereo channel) Hi EQ Low cut filter Physical Attributes and Power Built-in Power Supply Weight Dimensions (WxHxD) 100-240 VAC, 50/60 Hz 11.2 lbs (5.1 kg) 16 x 3.5 x 14 (407 x 89 x 357 mm) 2 K ohms 10 K ohms 1.1 K ohms 200 ohms 3-band, +/-15dB 80Hz 100-8k Hz, sweepable 800 Hz 3 kHz 12 kHz 75 Hz (-18 dB/oct) +10dBu +22dBu +28dBu 80dB

Dimensions

* All measurements are shown in mm/inches.