Intelligent Power System

A cars normal 12 V ~ 14 V power supply restricts output power to a theoretical limit of about 50 W through a 4 ohm load. For more power, all Pioneer PRS amplifiers use a PWM Regulated MOSFET power supply unit to boost the cars line voltage and control their own power supply. This control is exercised by Pioneer's Intelligent Power System, which does everything to ensure you get peak power output without noise by giving an extra current boost to the speakers to compensate for any drop in voltage caused by other electric loads in the car. You can now have the power you crave.
Mount PRS Series Amps Together
Mount two PRS series amplifiers together to create one massive amplifier. The mounting feet on the interior side can be removed or rotated inward to allow the amplifiers to mount flush against each other.
SEE NEXT PAGE FOR FULL FEATURES AND SPECIFIC ATIONS.
Bridgeable Power Amplifiers
Max. output power Continuous output power (RMS) (14.4 V) kHz/4 ohms kHz/2 ohms Bridged 4 ohms DIN output power (DIN45324, +B = 14.4 V) Variable Crossover network A channel B channel Low Frequencies (-12 dB/oct) High Frequencies (-12 dB/oct) LPF/HPF Network (-12 dB/oct) Input level/gain control PWM Regulated MOSFET power supply High Voltage Input capability (400 mV 6.5 V) Low load impedance capability (ohm) Variable Bass Emphasis (dB) Subsonic filter: 15 Hz (-24 dB/oct) Gold-plated RCA input and output terminals (full range) enabling Link Top connection Gold-plated screw-type speaker terminals Screw-type speaker terminals Large gold-plated power/ground terminals (screw type) High performance balanced isolator circuit Reversible endcaps for installation versatility MOSFET output section
4 x 150 W 2 x 500 W 4 x 37.5 W 4 x 75 W 2 x 150 W 4 x 115 W or 2 x 360 W LPF-Low, LPF High, HPF-Low, BPF LPF-Low, LPF-High, HPF Low, HPF-High Hz kHz
2 x 200 W 1 x 800 W 2 x 50 W 2 x 100 W 1 x 200 W 2 x 163 W or 1 x 486 W
2 x 120 W 1 x 400 W 2 x 30 W 2 x 60 W 1 x 120 W 2 x 87 W or 1 x 313 W

Hz Hz

Hz 60 Hz
Warning: Pioneer Power Series amplifiers are designed to supply higher output power than conventional amplifiers. Therefore, please use a subwoofer whose nominal input power is about twice the connected Power Series amplifiers continuous output power. * Not available in the UK.
Recommended System Set-Ups
To get the most from the DEX-P9R, Pioneer strongly recommends using it in combination with the DEQ-P9 and the PRS amp and speakers, to create a variety of system set-ups. The ultimate is a 4-way system with dedicated speakers for each frequency from ultra-lows to stratospheric highs. The DEQ-P9 splits the sound into the appropriate low to high frequencies and sends them along the Crossover Network to the correct speaker. Then Time Alignment steps in so each sound reaches your ear at the same moment.
Front 3-way Plus Subwoofer System

15 (9/16) 30 (1-1/4)

(6 -1 /4 )D ia.)
30 mm Polyester Fibre diaphragm Large Neodymium magnet (30.5 g) Die-cast aluminium flange Die-cast aluminium back chamber
Gold-plated terminals Nominal input power: 60 W 1,000 30,000 Hz, 92 dB (1 W/1 m)
6-3/4 (17 cm) Mid-Bass Driver
The TS-M7PRS Mid-Bass Driver was meticulously designed to reproduce real strings and vocals with less distortion. Thanks to the Aramid Fibre Composite Cone and the Butyl Rubber Symmetrical Balanced Surround, you can expect smooth, accurate sound from mid-bass to upper midrange frequencies. If it's precision control of sound you're after, the TS-M7PRS comes highly recommended. And you can combine it with the DEX-P9R and DEQ-P9R for the ultimate in acoustic pleasure.
143 (5 - 5/8 Dia.) 100 (4 Dia.)

170 (6 - 3/4 Dia.)

8.3 (5/16) 4 - 4.5 x 6.5 Holes (3/16 x 1/4 ) 67.3 (2 - 5/8)
Aramid Fibre Composite Cone woofer Symmetrically balanced Butyl Rubber Surround
Aluminium die-cast frame Gold-plated binding post-screw terminals Nominal input power: 60 W 28 10,000 Hz, 91 dB (1 W/1 m)

1200 W Max. Power

12 (30 cm) Dual Voice Coil Subwoofer
Introducing TS-W12PRS, a subwoofer that can handle real power and equipped with the Voice Coil Cooling System (VCCS), which together with a giant magnetic circuit, draws heat away from the inside of the sub, so that the sound stays natural and your subwoofer keeps its cool. There's also a 3 (76 cm) dual layer long voice coil (2 x 4 ohm) that, combined with the extremely light Aramid Fibre Composite Cone, results in a very strong moving force.

8 - 6.5 Holes (1/4 Dia.)

(11 - 7/ 8

322 (12 - 3/4 Dia.)

278 (11 Dia.)

19 (3/4)

133 (5-1/4) 152 (6)
Aramid Fibre Composite Cone woofer Dual Voice Coil design (2 x 4 ohm) Front VCCS (Voice Coil Cooling System) Aluminium die-cast frame Gold-plated binding post-screw terminals Low-Q design for use in small sealed box (28 liter 10 % recommended) Nominal input power: 300 W 15 2,000 Hz, 92 dB (1 W/1 m)

UD-N2PRS

95 33.3
2-Way Passive Crossover Network
Pioneer has designed a 2-way, passive crossover network especially for use with the TS-T3PRS and TS-M7PRS. With its discriminating EMI (Electromagnetic Interference) shielding chassis, the UD-N2PRS network provides simple, clear and precise sound solutions.
EMI (Electromagnetic Interference) shielding chassis Selected quality devices Tweeter attenuation: 0 dB/-3 dB
SEE PAGE 71 FOR SPEAKER TECHNIC AL PARAMETERS AND PAGE 77 FOR FULL FEATURES.
European Reference Separate Component Speaker Series
Inspired by the succesful development of the PRS speaker series, Pioneer launches its European Reference Seperate Component Speaker Series with standard European frame size. It offers bold music lovers an exciting opportunity to create a super high-quality sound system. These speaker systems contain carefully chosen, precision engineered woofers, tweeters and crossovers, all designed to bring you to new levels of sound perfection. The Pioneer Aramid Fibre Composite Cone Woofers bring both music and vocals right into your car, creating a warm and original sound. The Soft Dome Tweeter reproduces accurately the high notes while the Passive Crossover Network guarantees an optimal distribution of low and high frequencies from the amplifier to the woofers and tweeters. A guaranteed unforgettable listening experience!

4 x 100 W (2 x 240 W) Max. Power

4-Channel Amplifier

GM-X364
4 x 70 W (2 x 150 W) Max. Power

Specifications Features

LPF/HPF Network (A and B channel) (-12 dB/Oct) Input level/gain control PWM Regulated MOSFET power supply Speaker level input (A and B channel) Load impedance capability (ohm) Large screw-type power/ground terminals Screw-type speaker terminals High performance balanced isolator circuit RCA output

GM-X564

4 x 75 W or 2 x 200 W 4 x 75 W 4 x 60 W 2 x 120 W 10 Hz 50 kHz 0.dB 400 mV 6.5 V 27.x 61 x 324 5.0
4 x 45 W or 2 x 100 W 4 x 35 W 4 x 40 W 2 x 70 W 10 Hz 50 kHz 0.dB 400 mV 6.5 V 18.x 61 x 237 3.8

Hz

80 Hz
DIN output power (DIN45324, +B = 14.4 V) Continuous output power (RMS) Watts 14.4 V (kHz/4 ohms) (kHz/2 ohms) (Bridged 4 ohms) Frequency Response (Hz) (+o dB, -1 dB) Distortion (%) (10 W/1 kHz) S/N Ratio Input level control Max. Current Consumption (A/4 ohms) Chassis Size (W x H x D mm) Unit Weight (kg)
2-Channel Bridgeable Amplifier GM-X962
2 x 250 W (1 x 760 W) Max. Power

2-Channel Amplifier

GM-X562 GM-X362
2 x 80 W (1 x 200 W) Max. Power
2 x 130 W (1 x 300 W) Max. Power
LPF (-12 dB/Oct) Input level/gain control PWM Regulated MOSFET power supply Speaker level input (A and B channel) Load impedance capability (ohm) Large screw-type power/ground terminals Screw-type speaker terminals High performance balanced isolator circuit

GM-X962

2 x 175 W or 1 x 530 W 2 x 125 W 2 x 190 W 1 x 380 W 10 Hz 50 kHz 0.dB 400 mV 6.5 V x 61 x 324 5.0

GM-X562

2 x 90 W or 1 x 230 W 2 x 65 W 2 x 75 W 1 x 150 W 10 Hz 50 kHz 0.dB 400 mV 6.5 V 16.x 61 x 237 3.8

GM-X362

2 x 60 W or 1 x 150 W 2 x 40 W 2 x 50 W 1 x 100 W 10 Hz 50 kHz 0.dB 400 mV 6.5 V 11.x 61 x 157 2.6

80 Hz

Power Supply Unit
The power supply unit is central to the performance of any amplifier. A cars power supply is normally in the 12 V ~ 14 V range. This restricts the maximum output power to a theoretical limit of about 50 W through a 4 ohm load. For more output power, its necessary to boost the cars line voltage using a power supply unit. So most Pioneer amplifiers use a PWM Regulated MOSFET power supply. This means that the amplifier dynamically controls its own power supply and assures an extra current boost to the speakers to compensate for any drop in voltage caused by other electric loads in the car (e.g. switching on the defroster), which would result in power level fluctuations in non-regulated systems. The Pioneer regulated power supply provides maximum power to the speakers under real life operating conditions. MOSFETs create more power with less heat, so the resistance is lower. And with a higher thermal stability, performance is optimised at peak operating temperatures. With full MOSFET-driven power supplies, new Pioneer amplifiers are better than ever at delivering power! Pioneer Intelligent Power System optimises performance from turn-on to turn-off. This exclusive circuit manages the performance of the amplifier at all times. From preventing turn-on or -off thump to adjusting the PWM power supply to provide the power for that extra heavy bass note, it does everything to ensure you get peak power output without noise. Capacitors for the power supply work great to ensure enough power is available during peak usage, but without capacitance on the output stage many amplifiers will clip prematurely. Pioneer provide isolated banks for both that are optimised for each amplifier. Pioneer power amplifiers also use Parallel Coil Toroidal Transformers, which provide even higher voltage boost and lower magnetic flux leakage than normal toroidal transformers, further reducing noise in the audio system. Maximum performance of the new 2- or 4-channel amps is at 2 ohm (4 ohm mono) operation. This is perfect with a single 4 ohm subwoofer, or a pair of DVC subwoofers (wired in at 8 ohms each). If you want earth-shattering bass, upgrade to one of these Pioneer amplifiers!

TS-A2010

20 cm 66 mm 18 mm 25 30,000Hz 93 dB 90 W

TS-A6910

6x9 (163 x 237 mm) 66 mm 18 mm 25 30,000Hz 93 dB 80 W

TS-A1710

17 cm 42 mm 10 mm 28 30,000Hz 92 dB 50 W

TS-A1310

13 cm 42 mm 10 mm 40 30,000Hz 91 dB 35 W

350 W Max.

6 x 9 3-Way Speakers

153 x 225 84.265

330 W Max.

200 W Max.

150 W Max.

TS-A Speaker Series

The TS-A 6 x 9 speakers with their unique combination of oval woofers and midrange/tweeter cones, take full advantage of the boot space to produce rich,deep bass. They feature a Foamed IMPP Composite cone with an improved cone shape and surface finish and specially designed tweeters to achieve well balanced sounds. Corresponding to their attractive visual styling, these speakers achieve true large-speaker performance.

TS-A6988

6 x 9 4-Way Speakers

TS-A6968*

250 W Max.

TS-A6958

6 x 9 2-Way Speakers
6 x 9 (163 x 237 mm) Foamed IMPP composite cone woofer PPC (Pearl Polycarbon) balanced dome midrange () PPTA Balanced Dome mid-range () Foamed IMPP cone tweeter with Strontium magnet () Cone tweeter () Super tweeter () Tweeter () Frequency Response Sensitivity (1 W/1 m) Nominal input power 60 mm

60 mm

66 mm 42 mm 18 mm 25 32,000 Hz 93 dB 80 W 18 mm 25 30,000 Hz 93 dB 60 W 28 26,000 Hz 93 dB 40 W

Cross-Axial Speakers

TS-R1600II

120 W Max.

193.43
Cone woofer () Cone tweeter () Frequency Response Sensitivity (1 W/1 m) Nominal input power
16 mm 42 mm 30 25,000 Hz 90 dB 30 W

Surface Mount Speakers

TS-X150

60 W Max.

3-Way Speakers

40 W Max.

Full-range speaker () Cone Woofer () Horn midrange () Horn tweeter () Frequency Response Sensitivity (1 W/1 m) Nominal input power
13 cm 27 mm 20 mm 75 20,000 Hz 89 dB 20 W

180 20,000 Hz 88 dB 10 W

Midranges & Tweeters

TS-T23

Dome Tweeters

TS-S15

Tune-Up Dome Tweeters
Soft dome liquid crystal fibre (Polyarylate) tweeter () Soft dome styrene-rubber coated polyester tweeter () Cut-off frequency Cross over frequency Versatile mounting (3-way surface-mount) Slant spacer included In-line crossover network Frequency Response Sensitivity Nominal input power

6 x 8 3-way speakers

TS-H463

90 W Max.

Fiat, Lancia, Seat, Volkswagen

4 x 6 2-Way Speakers

133 x 203.7 62

TS-H104

Fiat, Lancia, Renault, Rover, Seat, Suzuki

TS-H103

Audi, BMW, Mercedes-Benz, Peugeot, Saab, Seat, VW, Volvo

TS-H871

8.7 cm 2-Way Speakers

Fiat*, Saab, Seat

103 45

90 102

* Fiat Punto with adaptor UD-M870.
IMPP Cone woofer with Urethane edge () Carbon-Graphite blended IMPP Cone woofer () Foamed IMPP Composite cone woofer with Butyl rubber edge () Foamed PPC (Pearl PolyCarbon) balanced Dome mid-range with Strontium magnet () PI Dome tweeter with Neodymium magnet () Dome tweeter () Cone-integrated coninal domes Frequency Response Sensitivity (1 W/1 m) Nominal input power 17 cm
6 x 8 (14.5 x 20.4 cm) 36 mm

4 x 6 (9.5 x 15.3 cm)

8.7 cm
26 mm 30 - 30,000 Hz 91 dB 50 W
26 mm 10 mm 40 - 30,000 Hz 90 dB 35 W 30 - 30,000 Hz 91 dB 50 W
26 mm 45 - 30,000 Hz 90 dB 25 W
26 mm 13 mm 45 - 30,000 Hz 90 dB 25 W 60 - 28,000 Hz 88 dB 15 W
SEE PAGES 64-71 FOR CUSTOM-FIT SPEAKERS APPLIC ATION CHART.
Separate Component Regular Grade Custom-Fit Speakers
Separate Component Regular Grade Custom-Fit Speakers are developed for those looking for high power handling and easy-fitting at an affordable price with better sound imaging thanks to the separate tweeters.

TS-1784-II

Alfa Romeo, Audi, Citron, Fiat, Ford, Lancia, Mercedes-Benz, Opel/ Vauxhall, Peugeot, Renault, Rover, Seat, Volkswagen

TS-1384

80 W Max.
Renault Mgane and Mgane Scnic

140 165

129 45

Specifications

IMPP Cone woofer with Urethane edge () PEI balanced Dome tweeter () Frequency Response Sensitivity (1 W/1 m) Nominal input power
17 cm 22 mm 35 30,000 Hz 90 dB 35 W
13 cm 22 mm 40 30,000 Hz 90 dB 25 W
Regular Grade Custom-Fit Speakers
Regular grade Custom-Fit speakers offer solid quality at an affordable price. So, what can you expect from Pioneers new custom fit speakers? Its possible to boost the power even higher. And enjoy a wider and smoother frequency response, thanks to the new blended IMPP Cone with grid pattern. The new 17 cm models feature an Easy connector making it simple to connect them up to the cars speaker connectors and the 10 cm models feature removable screw holes, allowing compatibility with round and square basket frames. Of course, all models offer outstanding value for money. With such an extensive choice, youre sure to find your sound solution here.

MOSFET50 and EEQ+ can be used together to get Direct Sub Drive. EEQ+ filters the rear channels output; then, MOSFET50 due to ample audio power drives Pioneer's high sensitivity subwoofers directly, without using a separate component amplifier. MOSFET50 can also drive 2 ohm speakers, pumping out an incredible 1 x 70 W in the rear, giving the unique setup of a 2 x 50 W front and 1 x 70 W subwoofer system.

Music Search

Locates the beginning of the next song for fast forward or the beginning of the present song on rewind.
Pioneer has incorporated the Non Interruption Philosophy into the Intelligent RDS Tuner for improved network following (NF). Thanks to the sophisticated algorithms, the different programme alternative frequencies are screened out and continuous, uninterrupted listening pleasure is achieved.

Built-in DAB

Pioneers headunit DEH-P90DAB features a built-in DAB Tuner, which allows access to Digital Audio Broadcasting for distortion-free CD-quality radio.

Dynamic Bass Emphasis

This feature digitally boosts low and high frequencies at lower volume levels to compensate for ambient road noise.

Dolby Digital

The current surround sound quality encoding standard, Dolby Digital means in-car movie theatre sound performance. The front left and right, centre, rear left and right speakers span frequencies from 20 Hz 20 kHz and there is a dedicated subwoofer channel for additional low frequency sound effects.

EEQ (Easy Equaliser)

For the maximum in customised in-car sound, Pioneer developed the Easy EQ (EEQ) system an incredible advancement over traditional bass/treble adjustments. Users can choose between one of the preset curves or the 3-band (parametric) equaliser curve. And with more parameters, it sounds like a Digital EQ system.

MiniDisc

MiniDisc Long Play is an encoding method for audio on MiniDisc that offers 320 minutes stereo (LP4). LP4 mode encodes audio in "joint stereo" mode, i.e. the left and the right channel simultaneously.

Dolby Pro Logic

The forerunner to the increasingly popular Dolby Digital format, Dolby Pro Logic Surround uses 5 speakers to create a cinematic surround sound ambience. By decoding sound data contained in Dolby Surround, it produces 4 disctinct outputs: front left, front right, centre and rear (2 speakers).

EEQ (Easy Equaliser) Plus
EEQ (Easy Equaliser) Plus expands EEQ further with either a Low Pass Filter (LPF) or a LPF plus High Pass Filter (HPF), for on-board network capability.

ATRAC 3

ATRAC3 is an audio compression technology used in MagicGate Memory Stick and MDLP. The digitised music data can be compressed into one-tenth of the volume of a conventional music CD. A 64 MB capacity Memory Stick can record about 60 minutes of music.
FIE (Front Image Enhancer)
This function shifts the sound focus forward electronically, without having to adjust the fader control, by cutting off high frequency signals to the rear speakers. It gives an extremely clear sound image in the front of the car, without attenuating dynamic bass response from the rear speakers
DTS 5.1 channel playback encoding technology is rapidly gaining popularity thanks to its dynamic sound impact from left, right and centre speakers.

DVD Video

The latest in multimedia digital technology, DVD, guarantees second-to-none picture quality. The ultra-sharp digital picture and surround sound bring impressive cinema into your car. Plus, DVD is packed with useful features s.a. multiple languages, soundtracks and subtitles, support for various multi-channel audio encoding technologies such as DTS and Dolby Digital.

Loudness Control

At low volume levels, low and high frequency sounds in music can be overpowered by ambient noise levels in the vehicle. Loudness control boosts these frequencies and provides better overall sound at low volume levels.

Check In/Check out

Check-out = transferring data from the DEH-P900HDD's built-in HDD to the MagicGate Memory Stick. Check-in = returning checked-out music data to the HDD. The Check-in can only be done by the HDD which did the Check-out. According to MagicGate regulation, it is possible to make four copies of the music data. One copy is recorded on the HDD, this which leaves you with 3 additional Check-out possibilities.

MOSFET 50 W x 4

The MOSFET50 Power Amp boosts audio performance levels by using revolutionary new semiconductor technology. Characteristics such as low loss, lower audio distortion, eliminated switching distortion and a wide power band combine to give MOSFET50 headunits 50 W x 4 of sonic clarity, matching the best component amplifiers.

ITS (Instant Track Selection)
Gives the choice of programming any favourite CD track for up to 24 tracks per disc. Selections are then played back utilising ADPS and the "Program" button.

Last Position Memory

Last Position Memory automatically resumes CD play from the last point if there is interruption to CD play.
ASL (Automatic Sound leveliser)
Automatic Sound Leveliser (ASL) technology electronically and automatically adjusts volume and frequencies to mask varying degrees of exterior noise.

SYSTEM CONTROL

AUX-In for External Music Sources
All Pioneer IP-Bus headunits units allow the connection of external music sources (with RCA outputs), such as portable recorders, micro-cassettes, etc., through the MCD bus connection. (Adapter CD-RB20).

AMPLIFIERS

Balanced Isolator Circuit
Prevents ground voltage flows from interfering with the signal. Pioneer improved existing designs by separating the left and right channel grounds. This puts each channels signal wave in phase, which helps cancel noise components within the grounds. The output is cleaner, with less interference.
in lower distortion, richer bass sounds and increased cone rigidity.

Crystalline IMPP Cone

This material with high young modulus and high propagation rate makes the cone more rigid and improves the transient response, resulting in accurate sound.

Double Damper

A damper supports the speaker cone and guides the cone as it moves back and forth during use. By using two dampers instead of one in many of its speakers, Pioneer has greatly improved linearity over the entire frequency range of the speaker.

DVD Control Line

This is used to connect the AVM-P9000R to the XDV-P9-II.

Input Level Control

Level Control adjustment is provided to match the amplifiers input with the source units output. Proper adjustment ensures less noise and distortion.

IP-Bus Control

The IP-Bus connections on Pioneer headunits allow the user to connect optional source units such as a TV Tuner, DVD player, Multi-CD player or DAB Tuner and create a true mobile multimedia centre.

This allows a Pioneer amplifier to be connected to an OEM radio without requiring costly add-on adapters. The added flexibility allows your Pioneer amplifier to be a part of your system as it grows and expands.

Variable Bass Emphasis

Allows bass frequencies to be boosted for each equipped amplifier. This allows the installer/user to set the optimal bass level for the speakers connected to that individual amplifier, allowing the user to best utilise the headunits tone controls for all speakers in the system.

Linear Power Response

With no roll to restrict the cones movements, this innovative system mimics a finely tuned precision piston, smoothly moving the speaker cone up to a higher level than ever. And thanks to its unique edgeless diaphragm, there is no stress or distortion around its diaphragm.

Neodymium Magnet

ERGONOMIC FEATURES
Pioneer OEL (Organic EL) display delivers high-contrast, moving 3-D images, even in sunlight. Its smart functionality lets the user control and confirm play source operating information and provides plenty of space for text, for lists of tracks, discs or other data from MDs or CDs. Pioneers latest OEL display is also larger, using a total of 256 x 80 pixels to offer even more entertainment features.

SPEAKERS

3-D Magnesium Hybrid Cone
The E-motion Series 3-D Magnesium Hybrid Cones produces purest, accurate sound with the most possible power through the use of an alloy of Magnesium and Aluminium.
Neodymium has a high magnetic flux density. It is about 7.5 times stronger than a standard magnet and allows Pioneer speaker designers to make a tweeter that is smaller and has reduced distortion as compared to a model using a standard magnet.

Power Blades

The Pioneer Magnesium Hybrid cone woofers give smoother low to upper midrange reproduction and high rigidity. The integration in the cone of Power Blades (protrusions) results in lower distortion, richer bass sounds and increased cone rigidity.
AG/LR (Anti-Glare Low-Reflection)
A specific coat used on Pioneer video screens minimises reflection and glare for comfortable viewing.

Aramid Fiber Cone Woofer

The woofer of the TS-C1700R and TS-C1300R was meticulously designed to reproduce real strings and vocals with less distortion. Thanks to the Aramid Fiber Cone with rubber edge, you can expect accurate, smooth sound from mid-bass to upper mid-range frequencies.

Selectable wide screen mode (Just/Full/Cinema/Zoom/Nomal) Wired Headphone mini jack 2 Dome Light

GEX-6100TVP

OPTIONAL TV TUNER FOR AVR-W6100
PAL TV Tuner 24 Station Presets (12TV1/12TV2) by BSSM (Best Station Sequential Memory)
System Connection Features
For AVR-W6100 cable output Antenna included

System Features

Country setting Picture Color/Sharpness adjustment

Specifications TV Tuner:

-Reception channels/TV system:
CCIR/B, G, H, K: VHF 2-12ch, UHF: 21-69ch, ITALY/B, G, H, K: VHF A-H2ch, UHF: 21-69ch, UK/IRE : UHF 21-69ch, OIRT/G,H, F, K: R1-R12ch, UHF21-69ch -Color system: TV: PAL Video: PAL

INFRARED HEADPHONE

Cordless Stereo Headphone Infrared Type
Noise Mute Function Volume Ajustment Included
Automatic Power Off Function
8-INCH WIDE SCREEN LCD COLOUR DISPLAY
8-inch wide TFT active matrix LCD colour display High quality Anti-Glare coating RGB input for Navigation system (with optional cable CD-65 RGB)
2 RCA AV Inputs (PAL/NTSC Video & L + R Audio) with S-Video 1 RCA AV Output (PAL/NTSC Video & L + R Audio) Auto Display brightness and backlight adjustment Remote Control sensor
Built-in high quality speaker (36 mm) with volume control Selectable wide screen mode (Just/Full/Cinema/Zoom/Normal)
6.5-INCH WIDE SCREEN LCD COLOUR DISPLAY
6.5-inch wide TFT active matrix LCD colour display High quality Anti-Glare coating Built-in high quality speaker (36 mm) with volume control 2 RCA inputs (PAL/NTSC video & L+R Audio) with S-Video
1 RGB input for AV Master or Navigation system (with optional cable CD-30RGB) 1 RCA AV output (PAL/NTSC Video & L + R Audio) Power Supply In Auto Display brightness and backlight adjustment
Remote control sensor for AV Master and Navigation System Selectable wide screen mode (Just/Full/Cinema/Zoom/Normal)
6.5-inch wide TFT active matrix LCD colour display High quality Anti-Glare coating One-touch detachable display for anti-theft Built-in high quality speaker (36 mm) with volume control Compulsory input for rear camera
2 RCA inputs (PAL/NTSC Video & L + R Audio) with S-Video 1 RGB input with RGB cable for AV Master or Navigation System 1 RCA AV output (PAL/NTSC Video & L + R Audio) Power Supply In Auto Display brightness and backlight adjustment

Remote Control sensor for AV Master and Navigation System Selectable wide screen mode (Just/Full/Cinema/Zoom/Normal)

GEX-P6400TVP

HIDE-AWAY TV TUNER
PAL TV Tuner 12 Station presets (12TV1/12TV2) by BSSM (Best Station Sequential Memory)
System Connection Features:
IP Bus Input/Output (controlled by AV Headunit, AV System Master and selected no. of Pioneer IP Bus headunits) 1 RCA AV Output (PAL/Video & L + R Audio) for rear display
Specifications: TV Tuner:
-Reception channels/TV system: CCIR/B, G, H, : VHF 2-12ch, UHF: 21-69ch, ITALY/B, G, H: VHF A-H2ch, UHF: 21-69ch, UK, Ireland/I: A-Kch, UHF 21-69ch, OIRT/D, K: R1-R12ch, UHF21-69ch -Color system: TV: PAL compatible
Country setting 4 Channel diversity antenna system (with optional antenna kit AN-G3) Card-type remote control
PAL, SECAM* TV Tuner 24 Station Presets (12 TV1/12 TV2) by BSSM (Best Station Sequential Memory)

System Features:

Country setting (4 country groups: CCIR, Italy, UK, OIRT) 4 Channel diversity antenna system (with optional antenna kit AN-G3) Card-type remote control Picture Colour/Sharpness adjustment
RGB input for Navigation system or AV System Master 2 RCA AV inputs (PAL/SECAM/NTSC Video & L + R Audio) for add-on game consoles, VCRs and others 1 RCA AV output (PAL/SECAM/NTSC** Video & L + R Audio) for rear display Independent Audio Video Selector for front display Independent Video Source Selector for rear display
- Colour system: TV: PAL/SECAM/NTSC compatible, Video: PAL/SECAM/NTSC compatible * Reception channels: note that SECAM tuner cannot receive SECAM L, as used in France. ** The Video output does not feature a conversion function between PAL, SECAM or NTSC.
- Reception channels/TV system: CCIR/B, G, H, K: VHF 2-12ch, UHF: 21-69ch, ITALY/B, G, H, K: VHF A-H2ch, UHF: 21-69ch, UK/I: UHF 21-69ch, OIRT/G, H, D, K: R1-R12ch, UHF21-69ch
IP-Bus input/output (controlled by AV System Master and selected Pioneer IP-Bus headunits) Built-in FM Modulator (for original headunit connection) RGB output for front display (AVX-P7300DVD, AV-P7000CD, AVX-7300, AVD-W6010, AVD-W6000)
MULTI-DVD PLAYER WITH DOLBY DIGITAL/ DTS DIGITAL OUTPUT
6-Disc DVD Video/Video CD/CD Player Built-in MPEG 2/1 decoder 24-bit D/A Converter Stand alone use with optional remote and remote sensor for rear AV entertainment
Optical digital output for Multi-Channel AV Master (AVM-P9000R) (DTS/Dolby Digital/Dolby Pro Logic/Linear PCM) Analogue IP-BUS output for front + RCA output for rear RCA Video Output (Front + Rear) GUI control with new OSD Region Number: 2
Controlled by AVM-P9000R and AVM-P8000R (except 5.1 channel sound reproduction). External control by any Pioneer IP-Bus headunit or AVM-P7000R. In this case the optional CD-R9 remote control and remote sensor are required.

Electronic Volume Gold-plated Power Screw Terminals Copper-plated chassis Installation Kit * Not available for HPF of High-mode.
12 (30 cm) DUAL VOICE COIL SUBWOOFER
Maximum input power: 1200 W Nominal input power: 300 W 15 2,000 Hz, 92 dB (1 W/1 m)
6-3/4 (17 cm) MID-BASS DRIVER
Aramid Fibre Composite Cone woofer Ready for small enclosure application (e.g. kick panel) Recommended enclosure volume: 5 Litres Symmetrically balanced Butyl Rubber Surround
Aluminium die-cast frame Gold-plated binding posts Maximum input power: 200 W Nominal input power: 60 W
28 10,000 Hz, 91 dB (1 W/1 m) Nominal impedance: 4 ohm
1 - 1/4 (30 mm) FLUSH MOUNT SOFT DOME TWEETER
30 mm Polyester fiber diaphragm Large Neodymium magnet (30.5 g) Die-cast Aluminium flange Die-cast Aluminium back chamber Gold-plated terminals
Removable metal mesh protector Flush mount application Maximum input power: 200 W Nominal input power: 60 W 1,000 30,000 Hz, 92 dB (1 W/1 m)
Recommended crossover frequency: 3,000 Hz Nominal impedance: 8 ohm
2-WAY, PASSIVE CROSSOVER NETWORK
EMI (Electromagnetic Interference) shielding chassis Selected quality devices Input capability: 200 W max, 60 W nom
Crossover Frequency 3.000 Hz -Low Pass Filter (LPF) -12 dB/oct. -High Pass Filter (HPF) -12 dB/oct.
Load impedance -Midrange (TS-M7PRS): 4 ohm -Tweeter (TS-T3PRS): 8 ohm Tweeter attenuation: 0 dB/-3 dB
1Even if a DVD-R(W) disc is recorded in Video format (Video Mode), it may not be playable as a result of scratches, dirt or characteristics specific to the disc, or dirt or condensation on the pickup lens. DVD-R(W) discs that havent been finalized, cannot be played. In general, discs recorded in the current format using a PC (personal computer) are playable. However, certain settings and application software environments may not be able to play these discs. Please ask your application software sales agent for more details. 2Use finalised music CD-R(W) discs for playback. In some cases, CD-R(W) discs may not play back correctly, unless they have been recorded using a CD-R(W) unit for recording music. Furthermore, CD players may not play back music CD-R(W) discs recorded from a music CDR(W) recorder as a result of scratches, dirt or characteristics specific to these discs, or, dirt or condensation on the pickup lens. Text information such as titles recorded on CD-R(W) discs may not be displayed. Read directions carefully regarding disc use before handling CDR(W) discs. Even if playback of a CD-RW disc is possible, it may take several seconds before actual sound reproduction begins.

Cassette RDS Tuner/MCD Player Features
MEH-P7300R FH-P4100R KEH-P7020R KEH-P6020R KEH-P6020RB KEH-P4020R KEH-P4023R KEH-P1010R KEH-P1013R KEH-1940
TUNER Adaptive RDS (PI, PS, AF, TP/TA) PTY (Search and Alarm) News interrupt feature Radio Text ARC FM BSA (Best TP Station Auto Search) High speed PLL Synthesiser tuner PNS (Pulse Noise Suppressor) No. of Presets BSM (Best Stations Memory) MD PLAYER MDLP with ATRAC 3 Sure Track system Track Search/Scan/Repeat Random play CASSETTE Auto-Reverse Full Logic Control Power load/eject Dolby NR Metal 70s Tape Selector Music Search Blank Skip and Repeat Radio Intercept Playing Time Tape Counter Head * AUDIO Max. output power (watts) DIN output power (watts: DIN45324, +B = 14.4 V) Built-in DSP EEQ Plus EEQ 5-mode preset equaliser(8) Custom preset equaliser 3-band parametric equaliser 3-band equaliser Source Equalisation Memory Selectable Loudness Selectable FIE (Front Image Enhancer) HPF LPF SFEQ (Sound Focus Equaliser) ASL (Automatic Sound Leveliser) Direct Sub Drive Spectrum analyser L/R level meter Source level adjuster Fader RCA Preout High Voltage Output GENERAL Multi-CD Control/CD Ready ITS (Instant Track Selection) Disc Title Memory CD Text Digital Compression/Dynamic Bass Emphasis Source TV Control Source CD Control DAB Tuner Control External unit control via IP-Bus AUX-In (with optional CD-RB20) Remote Control Ready Standard remote control ISO Connector Display illumination Dual button illumination Rotary volume Flap-type Front panel Removable Front Panel Cellular telephone auto muting Hands-free ready Voice Control with optional CD-VC60/65 Name & Access Soure Name & Access Radio Station Name & Access MCD Track or Disk(10)

ARC 5 24

ARC 5 24

ARC 5 24

ARC 5 18
B AUTO 4 x x 27 MOSFET 50 W x x 27 2
B AUTO MOSFET 50 W x x 27
AUTO MOSFET 50 W x x 27

MOSFET 50 W x x 27

4 x x 25

4 x x 22

2 3 (F+R+S/W or Non Fad) 2 OELMULTI Pop-up
2 3 (F+R+S/W or S/W)

2 1 1

2 (F+R or S/W)

2 (F+R or S/W)

EXT 2 BLUE

2 OELBLUE Pop-up (1)

EXT EXT EXT 1 MULTI/ BLUE (5) Pop-up (1)

EXT EXT 1 1

MULTI

MINT GREEN/ AMBER(5)

MINT GREEN/ AMBER(5)

(1)

CDX-P1270
CD PLAYER Oversampling digital filter D/A Converter Fast forward/reverse Track Search/Scan/Repeat Track/Manual search Random Play ITS (Instant Track Selection) ADPS (Automatic Disc Programming Selection) Last position memory Disc Title Memory CD Text Digital Compression Dynamic Bass Emphasis CD-R Playback CD-RW Playback GENERAL IP-Bus Output Standard remote control Display illumination Flexible angle installation Voice Control 8x 1 bit (11) (13) (10) (10) 0-90 (15)