20080403CD-VS33-E.Q3.3E

08.4.22 9:50 AM

Page 1

AUDIO VIDEO SELECTOR

ENGLISH

SLECTEUR AUDIO/VIDO

ESPAOL

Operation Manual

DEUTSCH

CD-VS33

Mode demploi

FRANAIS ITALIANO
This product conforms to new cord colors. Los colores de los cables de este producto se conforman con un nuevo cdigo de colores. Dieses Gert entspricht den neuen kabelfarben. Le code de couleur des cbles utilis pour ce produit est nouveau. Questo prodotto conforme ai nuovi codici colori.

NEDERLANDS

ENG/MASTER 96

Page 2

Contents
Before Using this Product. 2
About this Product.. 2 Precaution... 2
Part Names And Applications. 14
Controller Unit.. 14 Hide-away Unit.. 15

Connecting the Units.. 3

Connecting the Power Cord and Controller Unit. 4 Connecting the System (1).. 5 Connecting the System (2).. 7 Connecting the Audio/Video equipment. 9

Specifications.. 16

Installation.. 10
Installing Hide-away Unit.. 10 Installing Controller Unit.. 11

Page 3

Before Using this Product

About this Product

This product is a rear-seat audio-video selector that enables you to switch the display between audio and video.
I When using this product
We recommend that you familiarize yourself with the functions and their operation by reading through the manual before you begin using this product. It is especially important that you read and observe the Precaution on this page and in other sections.

Precaution

Keep this manual handy as a reference for operating procedures and precautions. Protect this product from moisture. Do not set a high volume level when using headphones to listen. Listening to high volumes for extended periods of time can have an adverse effect on hearing.

WARNING

Handling the cord on this product or cords associated with accessories sold with the product may expose you to chemicals listed on proposition 65 known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. Wash hands after handling. Connect the product to a display that cannot be seen by the driver. If the display can be installed only where it is visible to the driver, use a display that can detect the ON/OFF status of the parking brake, and be sure to install the display correctly so that it always works in conjunction with the parking brake switch. To avoid the risk of accident and the potential violation of applicable laws, this product is not for use with a video screen that is visible to the driver. In some countries or states the viewing of images on a display inside a vehicle even by persons other than the driver may be illegal. Where such regulations apply, they must be obeyed.
FRANAIS ITALIANO NEDERLANDS 2

Page 4

Connecting the Units
This product is for vehicles with a 12-volt battery and negative grounding. Before installing it in a recreational vehicle, truck, or bus, check the battery voltage. To avoid shorts in the electrical system, be sure to disconnect the battery cable before beginning installation. After completing installation and wiring, double check that there are no mistakes. Re-install any parts removed from the car during installation, then connect the battery negative terminal. Refer to the owners manual for details on connecting the various cords of the power amp and other units, then make connections correctly. Secure the wiring with cable clamps or adhesive tape. To protect the wiring, wrap adhesive tape around them where they lie against metal parts. Route and secure all wiring so it cannot touch any moving parts, such as the gear shift, handbrake and seat rails. Do not route wiring in places that get hot, such as near the heater outlet. If the insulation of the wiring melts or gets torn, there is a danger of the wiring short-circuiting to the vehicle body. Do not shorten any leads. If you do, the protection circuit may fail to work when it should. Never feed power to other equipment by cutting the insulation of the power supply lead of the unit and tapping into the lead. The current capacity of the lead will be exceeded, causing overheating. When replacing a fuse, be sure to use only a fuse of the rating prescribed on the fuse holder. Always grip the Controller unit when connecting an RCA pin plug.

Page 5

Connecting the Power Cord and Controller Unit

Hide-away unit

ESPAOL DEUTSCH
Fuse holder (1 A) 2m Red To electric terminal controlled by ignition switch (12V DC) ON/OFF. 2m Black (ground) To vehicle (metal) body.

FRANAIS

Controller unit rear side

ITALIANO

Groove Cord Controller unit Route the controller unit cord inside the slot groove on the controller unit rear side. Do not pull strongly, excessively bend or stretch the cord.

NEDERLANDS 4

Page 6
Connecting the System (1)
Connecting cords with RCA pin plugs (sold separately)

AV OUT (1 3)

AV IN (2 3)

Page 7

Rear Display 2 AVD-W8000, etc Display Audio input Hide-away unit Video input
Rear Display 1 AVD-W8000, etc Display Hide-away unit Audio input Video input
Rear Display 3 AVD-W8000, etc Audio input Hide-away unit Display

Video input

Video output for rear Multi-DVD player XDV-P9 Audio output Video output Portable video (sold separately), etc Audio output

Page 8

Connecting the Units A Title (English)
Connecting the System (2)

Page 9

TV TUNER GEX-P7000TV
Front Display AVX-P7000CD, etc

Audio output

Video output Rear Display 2 AVD-W8000, etc Display Audio input Hide-away unit Video input Rear Display 3 AVD-W8000, etc Audio input Hide-away unit Display Hide-away unit Audio input Rear Display 1 AVD-W8000, etc Display Video input

AVM-P9000R

Video output for rear Multi-DVD player XDV-P9 Audio output

Page 10

Connecting the Audio / Video equipment

Controller unit

3.5 mini pin plug
Headphones (sold separately)

Video output

8mm video, vehicle-mounted portable video, etc.

Page 11

Installation
Before finally installing the unit, connect the wiring temporarily, making sure it is all connected up properly, and the unit and the system work properly. Use only the parts included with the unit to ensure proper installation. The use of unauthorized parts can cause malfunctions. Install the unit where it does not get in the drivers way and cannot injure the passenger if there is a sudden stop, like an emergency stop. When mounting this product, make sure none of the leads are trapped between this product and the surrounding metalwork or fittings. Do not mount this product near the heater outlet, where it would be affected by heat, or near the doors, where rainwater might splash onto it. If this product is installed in the passenger compartment, anchor it securely so it does not break free while the car is moving, and cause injury or an accident. If this product is installed under a front seat, make sure it does not obstruct seat movement. Route all leads and cords carefully around the sliding mechanism so they do not get caught or pinched in the mechanism and cause a short circuit. Install the controller in a safe place where it can be easily operated from the rear seat. Never install the controller on the dashboard where it will be exposed to the direct rays of the sun. It could be damaged by high temperatures. In attaching L-fixtures to the controller unit with screws, be careful not to overtighten the screws or tighten them slanted. An expanded screw hole might result, disabling attachment of the L-fixtures. The L-fixture can be bent to match the installation location.

ENGLISH ESPAOL DEUTSCH

Installing Hide-away Unit

Velcro tape (hard)

Car mat

Page 12

Installing Controller Unit
I Installation using the L-fixture
The controller unit, when installed with L-fixtures, can be tilted for optimal ease of use. Peel off the paper backing of the double-sided tape of the L-fixture and adhere to the installation location.
1. Attach L-fixtures to the controller unit finger-tight.

Keep the screws loose.

Screw L-fixture Controller unit
2. Paste double-sided adhesive tape to the intended installation position of the controller unit.

Remove release paper

Bend the L-fixtures to meet the shape of the intended installation position of the controller unit.

Page 13

3. Release the controller unit from the L-fixtures once. ENGLISH ESPAOL
4. Press the L-fixtures firmly against the intended installation position of the controller unit.

DEUTSCH FRANAIS ITALIANO

5. Attach the controller unit to the L-fixtures.

NEDERLANDS 12

Page 14
6. Adjust the installation angle of the controller unit.
Adjust the angle for optimal ease of use.
7. Secure the controller unit firmly with the L-fixtures.
Tighten the screws fully. Note:
Be careful not to overtighten the screws or tighten them slanted. An expanded screw hole might result, disabling attachment of the L-fixtures.
I Installation using Velcro tape
Adhere the Velcro tape (hard) (provided) to the back of the controller unit, adhere the Velcro tape (soft) to the installation location and then install.
Velcro tape (hard) Controller unit Velcro tape (soft)

Page 15

Part Names And Applications

Controller Unit

VOLUME PHONES A VOLUME is used to adjust the volume of the headphones connected to PHONES A. PHONES B VOLUME is used to adjust the volume of the headphones connected to PHONES B. Rotate counterclockwise to reduce the volume and rotate clockwise to increase the volume.
SOURCE SELECTOR (1 3) Used to switch the video and audio connected to the AV IN jack (1 3) for each AV OUT jack (1 3).

ESPAOL DEUTSCH FRANAIS

Power indicator, power switch The power is turned on or off alternately each time the power switch is pressed. The power indicator lights when the power is on.
Headphone output jacks The mini pin plug of headphones can be connected to PHONES A or PHONES B. The audio from AV OUT 1 is output from the headphones connected to PHONES A. The audio from AV OUT 3 is output from the headphones connected to PHONES B.
AV IN jacks (1) RCA video input (yellow) RCA audio input (white, red) Used to connect 8mm video, vehicle-mounted portable video, etc.

ITALIANO NEDERLANDS 14

DRM-624X Six Disc CD-ROM Changer SPECIFICATIONS
GENERAL Media Type Media Diameter Interface Block Size Data Transfer Rate Capacity of Data Buffer Average Seek/Access Time Disc Change Time (without Spin-Up, Spin-Down) MTBF Regulatory Approval CD-ROM, CD-Audio, XA Mode 2, Form 1 and 2 120mm SCSI-2 2048/512 Byte (selectable) 676 Kbytes/Sec (Sustained) 128 Kbytes (ABS*) 110/150 mSec Less than 5 Sec 50,000 POH UL, CSA, FCC Class B, VDE, TUV, SEMKO, BEAB, NEMKO, DEMKO, FIMKO, SEV, CE
AUDIO PERFORMANCE Frequency Response 4 ~ 20,000 Hz 2dB Total Harmonic Distortion 0.1% (Max) Output Voltage 1.7 V r.m.s. (line out) 0.5V (10K) PHYSICAL CHARACTERISTICS Dimension (W x H x D) 210 x 88.3 x 370.5 mm Weight (Net) 3.4 Kg Weight (Shipping) 4.8 Kg Operating Voltage 100 ~ 240V 50/60Hz Rated Current Consumption AC 120V 0.11A, AC240V 0.10A Max. Current Consumption AC 120V 0.31A, AC240V O.20A ENVIRONMENTAL CONDITIONS Operating Temperature 5 ~ 40C Storage Temperature -20 ~ 60C Humidity (non-condensing) 5 ~ 85% RH ACCESSORIES DRM-ADisc Magazine PCA-02 SCSI Daisy Chain Cube
*ABS: Advanced Buffering System