ORDER NO.

RRV2320

DVD PLAYER

KU/CA LB RL RL/RD WY
DV-S77 DV-S737 DV-737 DV-737-K
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).
DV-37 Model DV-S77 DV-S737

DV-737 DV-737-K

Power Requirement
AC120V AC110V AC110-127V/220-240V AC110-127V/220-240V AC220-240V

Region No.

Remarks

CONTENTS

1. SAFETY INFORMATION.. 2 2. EXPLODED VIEWS AND PARTS LIST.. 4 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM. 12 4. PCB CONNECTION DIAGRAM.. 39 5. PCB PARTS LIST.. 52 6. ADJUSTMENT... 58 7. GENERAL INFORMATION.. 7.1 DIAGNOSIS.. 7.1.1 TEST POINTS LOCATION. 7.1.2 TEST MODE SCREEN DISPLAY. 7.1.3 TROUBLE SHOOTING. 7.1.4 ERROR CODE.. 7.1.5 DISASSEMBLY. 7.2 IC... 8. PANEL FACILITIES AND SPECIFICATIONS. 84
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
c PIONEER CORPORATION 2000
T IZE AUG. 2000 Printed in Japan
DV-37, DV-S77, DV-S737, DV-737, DV-737-K

1. SAFETY INFORMATION

This service manual is intended for qualified service technicians ; it is not meant for the casual do-ityourselfer. Qualified technicians have the necessary test equipment and tools, and have been trained to properly and safely repair complex products such as those covered by this manual. Improperly performed repairs can adversely affect the safety and reliability of the product and may void the warranty. If you are not qualified to perform the repair of this product properly and safely, you should not risk trying to do so and refer the repair to a qualified service technician.
WARNING This product contains lead in solder and certain electrical parts contain chemicals which are known to the state of California to cause cancer, birth defects or other reproductive harm. Health & Safety Code Section 25249.6 Proposition 65
NOTICE (FOR CANADIAN MODEL ONLY) Fuse symbols (fast operating fuse) and/or be of identical designation.
(slow operating fuse) on PCB indicate that replacement parts must
REMARQUE (POUR MODLE CANADIEN SEULEMENT) Les symboles de fusible (fusible de type rapide) et/ou de remplacement doivent avoir la mme dsignation.
(fusible de type lent) sur CCI indiquent que les pices

(FOR USA MODEL ONLY)

1. SAFETY PRECAUTIONS
The following check should be performed for the continued protection of the customer and service technician.
ANY MEASUREMENTS NOT WITHIN THE LIMITS OUTLINED ABOVE ARE INDICATIVE OF A POTENTIAL SHOCK HAZARD AND MUST BE CORRECTED BEFORE RETURNING THE APPLIANCE TO THE CUSTOMER.

LEAKAGE CURRENT CHECK

Measure leakage current to a known earth ground (water pipe, conduit, etc.) by connecting a leakage current tester such as Simpson Model 229-2 or equivalent between the earth ground and all exposed metal parts of the appliance (input/output terminals, screwheads, metal overlays, control shaft, etc.). Plug the AC line cord of the appliance directly into a 120V AC 60Hz outlet and turn the AC power switch on. Any current measured must not exceed 0.5mA.

2. PRODUCT SAFETY NOTICE

Many electrical and mechanical parts in the appliance have special safety related characteristics. These are often not evident from visual inspection nor the protection afforded by them necessarily can be obtained by using replacement components rated for voltage, wattage, etc. Replacement parts which have these special safety characteristics are identified in this Service Manual. Electrical components having such features are identified by marking with a on the schematics and on the parts list in this Service Manual. The use of a substitute replacement component which does not have the same safety characteristics as the PIONEER recommended replacement one, shown in the parts list in this Service Manual, may create shock, fire, or other hazards. Product Safety is continuously under review and new instructions are issued from time to time. For the latest information, always consult the current PIONEER Service Manual. A subscription to, or additional copies of, PIONEER Service Manual may be obtained at a nominal charge from PIONEER.
Device under test Test all exposed metal surfaces
Reading should Leakage not be above current 0.5mA tester
Also test with plug reversed (Using AC adapter plug as required)

Earth ground

AC Leakage Test
WARNING ! THE AEL (ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS 1. A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.

NSP Power Cord Warranty Card Remote Control Unit Battery Cover Packing Case Polyethylen Bag B5 Operating Instructions (English) Operating Instructions (English) Operating Instructions (Trad-Chinese) Operating Instructions (English, French, German, Italian) ADG7021 ARY1026 VXX2714 VNK4423 VHG1996 Not used VRB1262 Not used Not used Not used ADG7006 Not used VXX2628 VNK4677 VHG1994 VHL1051 Not used VRB1255 VRC1121 Not used ADG1127 Not used VXX2628 VNK4677 VHG1995 VHL1051 Not used VRB1255 VRC1121 Not used ADG1127 Not used VXX2627 VNK4423 VHG1998 VHL1051 Not used VRB1255 Not used Not used ADG1127 ARY7022 VXX2628 VNK4677 VHG1985 Not used Not used Not used Not used VRE1086 ADG1127 ARY7022 VXX2627 VNK4423 VHG1997 Not used Not used Not used Not used VRE1086
18 Operating Instructions (Dutch, Swedish, Spanish, Danish)

Not used

VRF1055

2.2 EXTERIOR SECTION

RL, RL/RD and WY Types 41 Only
Refer to "2.4 LOADING MECHANISM ASSY". 8 47
KU/CA and 15 LB Types Only
RL, RL/RD and WY Types Only 44 N K 44
49 LB, RL and RL/RD Types Only 44 45

KU/CA Type Only 50

7 RL, RL/RD and WY Types Only 44 44

44 M 3

WY Type Only
Refer to "2.3 FRONT PANEL SECTION".
(1) EXTERIOR SECTION PARTS LIST

5 NSP NSP NSP 24 25

DVDM Assy AJKB Assy DJKB Assy VJKB Assy SCRB Assy MSWB Assy POWER SUPPLY Unit Loading Mechanism Assy AC Inlet Assy Earth Lead Wire Flexible Cable (28P) Flexible Cable (18P) Flexible Cable (28P) Flexible Cable (12P) Housing Assy Bottom Plate Insulator Tray Stopper Spring Mini Card Spacer Cushion Bonnet S Rear Panel Sub Chassis Chassis Clamper Plate
See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) VWR1333 VWT1180 See Contrast table (2) DE012VF0 VDA1845 VDA1847 VDA1848 VDA1849 See Contrast table (2) PNA2376 PNW2766 VBH1277 VEC2173 VEC2174 See Contrast table (2) See Contrast table (2) See Contrast table (2) VNA2246 VNE2068

NSP NSP 50 51

Bridge Panel Stay PCB Stay Tray Clamper Tray Stopper Power Joint Power Button Switch Holder DVD Badge Door Panel Dor Holder Door Spring Connector Assy Flexible Cable (20P) Caution Label Screw Screw Screw Screw Screw Screw Screw Screw Label Screw
VNE2069 VNE2156 VNE2214 See Contrast table (2) VNL1738 VNL1739 See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) See Contrast table (2) VBH1331 See Contrast table (2) See Contrast table (2) See Contrast table (2) VBA1057 ABZ30P080FMC IBZ30P060FCC BBZ30P080FCC BBZ30P100FZK BBZ30P100FMC BPZ26P080FZK See Contrast table (2) See Contrast table (2) See Contrast table (2)

X601 X951 CHIP CERALOCK (20MHz) CHIP CRYSTAL (27.0MHz) FLEXIBLE CABLE 07P DSS1110 VSS1086 VDA1681 VEK1060 VKN1464 VKN1475 VKN1498 VKN1608 VKN1618 VNF1109
P101 CHIP FUSE (0.8A) CN120 24P FFC CONNECTOR CN105 16P FFC CONNECTOR CN104,CN512 12P FFC CONNECTOR CN122 18P FFC CONNECTOR CN101,CN103 28P FFC CONNECTOR KN1 EARTH METAL FITTING

RS1/16S J

IC103,IC104 IC101,IC102 IC109 IC107 IC1108 Q103,Q104 Q101,Q102 Q105,Q106 Q107,Q108 D101,D102,D107 AD1854JRS NJM5532MD NJM78M05FA NJM78M09FA NJM79L09A 2SA1037K 2SD2114K 2SK2033 DTC124EK EP10QY03

All Resistors

SEMICONDUCTORS OTHERS
JA901 OPTICAL LINK OUT GP1FA550TZ JA931,JA932 RKN1004 REMOTE CONTROL JACK JA911 1P PIN JACK (BLK) VKB1160 CN901 12P FFC CONNECTOR VKN1243 CN902 7P FFC CONNECTOR VKN1267
L108,L109 CHIP BEAD VTL1081
IC606 IC607 IC609 IC601-IC604 Q618,Q621,Q624,Q627 Q602,Q603 Q601,Q608-Q610 Q614,Q616 Q613,Q615 Q619,Q622,Q625,Q628 Q604-Q606,Q611,Q612 D621-D623 D614-D616 D601-D604 D618-D620 NJM78M06FA NJM78M09FA NJM79M06FA TK15420M 2SA1037K 2SC2412K 2SC4081 DTA143EK DTC143EK HN1C01F IMZ1A DA204K EP10QY03 MA111 UDZS5.6B C117,C118,C124 C184,C185 C1128,C1129,C1132 C115,C116,C195,C197,C226 C228 C119,C120,C126,C127 C130,C131,C133,C190-C193 C109-C112 C101-C104 C105-C108 CEAT221M10 CEGA470M25 CEBA470M63 CKSQYF104Z50 CKSQYF104Z50 CKSRYF104Z25 CKSRYF104Z25 CQHA122J2A CQHA181J2A CQHA391J2A
C194,C196,C227,C229 (100F/10V) VCH1192 C113,C114,C186-C189 (100F/25V) VCH1193
R115,R116 R119-R122 R101-R104,R113,R114 R117,R118,R123-R128 R254,R255,R260,R261 Other Resistors RDR1/4PM104J RDR1/4PM152J RDR1/4PM221J RDR1/4PM332J RS1/10S0R0J RS1/16S J
L701,L704,L707 L710,L713,L716 L719,L722,L725 L790-L792 CHIP BEAD CHIP BEAD CHIP BEAD CHIP BEAD VTL1082 VTL1082 VTL1082 VTL1076

S601 VSH1020

JA101 JA102 CN101 2P PIN JACK (WHITE) 2P PIN JACK (RED) 18P FFC CONNECTOR SCREW TERMINAL KN101,KN103,KN104 EARTH METAL FITTING VKB1139 VKB1140 VKN1249 VNE1948 VNF1084
C790,C791 C671,C674 C841 C608,C610 C699 C617,C627 C601,C603,C606,C613,C616 C621,C623,C626,C631,C641 C643,C646,C742,C744,C762 C764 CCSRCH101J50 CCSRCH102J50 CCSRCH470J50 CEAT101M10 CEAT101M50 CEAT471M16 CEV100M16 CEV100M16 CEV100M16 CEV100M16 CEV470M6R3 CKSRYB103K50 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF104Z25 CKSRYF105Z10

Q911 D931 2SC2412K MA111

L911 NOISE FILTER RTF1167
C651,C657,C704 C662,C684 C604,C605,C607,C609 C614,C615,C618,C624,C625 C628,C644,C645,C741,C743 C751,C753,C761,C763,C771 C773 C672,C673,C675,C676

(13) Internal operation mode of mechanism controller [MM : ] Internal mechanism mode (2 digits) and internal mechanism step (2 digits) of the mechanism controller (14) 1 Disk sensing [DSC ] The type of discs loaded is displayed. [DVD], [CD ], [VCD], [ ] 2 CD 1/3 beam switch [BM ] (15) 1 Equalizer value [E ] 2 Jitter value [J ] nake the jitter four times, and renew it in every one second. [4 * *] CD is effective only in the jitter value. (16) Version of the AV-1 chip [ AV : . ' ' ] (17) 1 Version of the FL controller [FL : ] 2 Region setting of the player [REG : ] Setting value

[1] to [6]

(18) Destination setting of the FL controller [MDL : / ] For charactors in front represent the type of model : There charactors that follow represent the destination code. J : /J, K : /KU, /KC, /KU/KC, R : /RAM, /RL, /RD, /LB, WY : /WY (19) The part number of the flash ROM and system controller [ / ] 1 Part number of the flash ROM <Front> (Example) VYW1536-A = W1536A (Example) PD6256A9 = 6256APart number of the system controller <Rear> (Example) PD3381T1 = 3381T1

7.1.3 TROUBLE SHOOTING

No Power ON FL is not turned ON FL indication is unusual
START Blow out fuse of the primary side Blow out micro-fuse on the POWER SUPPLY Unit. (Check the each voltage.) (P101, P102, P103) Blow out resistor on the POWER SUPPLY Unit. (R104) FL controller IC (IC101) on the FLKY Assy is damaged.

Power ON

Turn on the power again after 2 - 3 minutes. Check the following connections : POWER SUPPLY Unit - DVDM Assy DVDM Assy - FLKY Assy FLKY Assy - PWSB Assy Check each voltage (EV+5V, SW+5V, SW+3.3V, +8V, +12V, -12V and -27V) (If above voltage are not supplied, check the micro-fuse.)

Is FL turn on ? Yes

Is the indication of FL normal ? Yes
FL indication is dark or flickers.
Short or open the zenner diode on the POWER SUPPLY Unit. (ZD102) Check the values of R118 on the FLKY Assy. Do not you set FL DIMMER ON ?
Indicates the error message
Refer to the section "7.1.4 ERROR CODE".
Blow out micro-fuse (P101) on the DVDM Assy. Blow out micro-fuse (P103) on the POWER SUPPLY Unit.

Is tray open ? Yes

Check the connection between LOSB Assy and DVDM Assy. (12P flexible cable) Check the +8V power supply voltage (above micro fuse).
Do the video and sound come on ? Yes
Check the following connections : DVDM Assy - AJKB Assy DVDM Assy - VJKB Assy DVDM Assy - DJKB Assy AJKB Assy - SCRB Assy (WY type) VJKB Assy - SCRB Assy (WY type) Check each voltage (+8V, +12V and 12V) [If above voltage are not supplied, check the micro-fuse(P101, P102, P103).] Indicates the error message Refer to the section "7.1.4 ERROR CODE".

Auto sequence 52 timeout of focus jump down 53 Auto sequence timeout of focus
Auto sequence timeout of play AGC Auto sequence 55 timeout of disc-typesensing 56 Auto sequence timeout of ATB2

Stop Stop

Auto sequence 57 timeout of tracking servo ON Auto sequence 58 timeout of ATB1 Auto sequence 59 timeout of focus gain adjustment Auto sequence 5A timeout of tracking gain adjustment Auto sequence 5B timeout of offset adjustment Auto sequence 5C timeout of modulation factor measurement Auto sequence 5D timeout of auto focus bias 5F Auto sequence already busy

Stop Stop Stop

ABUSY did not return within 200 mS after the ADJMIR (modulation factor measurement) command was sent.
ABUSY did not return within 2 seconds after the AFB (auto focus bias) command was sent. A command could not be sent because ABUSY was low. ABUSY did not return within 200 mS after TLV command was sent. Pause mode could not be restored within three retries after it had been released.

Stop Continues operation

62 Pause retry error
ID can not read during tracing
An ID could not be read for 1 second or more.

Operation of the Unit

Subcode check failure during playback ID can not read at 73 the startup 74 Subcode check failure during startup
No frame could be read for 3 seconds or more. An ID could not be read within 1 second after the AFB adjustment had been finished. No subcode could be read within 3 seconds after AFB adjustment had been finished. TOC readout took 30 seconds or more.
Opens (ID readout failure) Opens (Subcode readout failure).
Timeout for reading 81 TOC of the mechanism controller Timeout for reading 82 TOC of the system controller Communication A1 timeout of DSP command A command could not be issued to DSP because Command Busy (XCBUSY) was in force (XCBUSY = L) for a specified time (about 200 mS). Command Busy (XCBUSY) was in force for a specified time (about 200 mS) before and after a coefficient read command was issued to DSP, or the address echo-back after command issuance did not match the setup address. Command Busy (XCBUSY) was in force for a specified time (about 1024 mS) before and after the coefficient write command was issued to DSP. Command Busy (XCBUSY) was in force for 200 mS during continuous coefficient writing, or before and after a continuous write command was issued to DSP.

Reading TOC of the system Stop controller took 30 seconds or more.

No operation

Communication A2 timeout for reading DSP coefficient Communication A3 timeout for writing DSP coefficient Communication A4 timeout for continuously writing DSP coefficient B1 Timeout error for backup Retry error for backup
In the tracing state during the backup sequence, codes could not be read for 1 second or more. In the backup sequence, tracking ON sequence of the servo DSP could not be completed even if more than 500 mS after the tracking ON command was issued. Tracing impossible after retring the tracking ON for 3 times in the backup sequence. During tracing, runaway was detected after three iterations of backup operations for detecting runaway.
Stops Stops Stops (the mechanical controller operates independently). Turns off the power instantly (No indication on the FL display and no writing to flash memory) Stops
B3 Retry error for trace C3
Detection of tracking During playback, the overcurrent detection port was at L for 300 ms or more overcurrent continuously. Short-circuit test corresponding error Violation against digital copy guard While the power was on, the overcurrent detection port was at L for 40 ms or more continuously.

F5 Tray being pushed

The tray switch that had been Open mode was forcibly changed to a mode other than Closes Open by an external force. Reverses the loading Loading, unloading or clamping could not be completed within a specified time (about direction. It timeout is 5 seconds). repeated upon retry, the unit stops. The following error occured eight times. (1) Focus ON sequence could not be completed even if more than two seconds after the focus ON command (to the servo DSP) was sent. (2) Focus IN sequence was finished, actually focus IN was not completed. Stops wherever possible then opens (stops in the case of side B).

F8 Loading timeout

FC Focus
Error codes that are displayed on the FL display by using the remote control unit (Device error) To display : ESC + DISPLAY + DISPLAY ; Location of the display : At the two digits of left of the FL display

XCS3/XCASL

XCS3 GND HCPUCK V+3D GND 36MVH V_SEL2 V+3D GND EXTAL XTAL V+3D XCSDF0 GND XAMUTE 44X48 3DON V+3D XCSADSP0 XAVSRST

O O GND N.C. V+3D

Function
PE5108A (BY CHIP) chip select signal output
I/O N.C. I/O N.C. O O O O O O O O I O O O O O O O O O O I O I O O GND N.C. N.C. Clock generator Composite/S switching signal output of the skirt terminal [WY model] V+3D N.C. N.C. N.C. N.C. GND Connect a ceramic resonator V+3D DAC chip select signal output ( XLAT3) N.C. N.C. N.C. N.C. GND N.C. N.C. Last stage mute signal output of the audio DAC 44/48 FS switching signal output N.C. 3D audio ON/bypass switching signal output V+3D CD deck synchronous input Sync. reset port N.C.
PORTF6 PORTF7 GND AVSS AVCC OUTA_P VREF OUTB_P AVSS AVSS PORTE0 PORTE1 PORTE2 PORTE3 PORTE4 PORTE5 PORTE6 PORTE7 PORTD0 VCC PORTD1 PORTD2 PORTD3 PORTD4 GND PORTD5 PORTD6 PORTD7 PORTJ0 PORTJ1 PORTJ2 PORTJ3 VCC PORTJ4 PORTJ5 PORTJ6 PORTJ7 PB0/TIOCA2 PB1/TIOCB2 PB2/TIOCA3 VCC PB3/TIOCB3 PB4/TIOCA4 XMTEST XCPUMD XRES
XCSVE GND GND V+3D LODRV V+3D TEI GND GND V_SEL FOFST1 FOFST2 XDFINH DVD/XCD LD1_ON LD2_ON V+3D DPD/TE AGOFF XCD2X OEICG GND XMON XDRVMUT XDSPRST V+3D TM_ENT VSEL_SW XCBUSY XABUSY XINT2 V+3D LT1 SBSY XRESET

O O O O O I I N.C.

Serial communication enable signal output of the video encoder [WY model] GND GND V+3D Loading drive output V+3D Tracking offset signal output GND GND Component/composite switching signal output N.C. N.C.
I/O Focus offset adjustment output 1 I/O Focus offset adjustment output 2 I/O Defect shunt signal output O O O O O O O O O I O O O I I O I I I I I O I I I I DVD/CD switching signal output 650 nm laser diode ON signal output 780 nm laser diode ON signal output V+3D 1 beam/3 beams switching signal output AGC ON/OFF switching signal output of RF IC Signal output for switching the double speed playback (VCD) OEIC gain switching signal output GND ON/OFF switching signal output of the spindle motor control output N.C. N.C. Driver mute output N.C. Servo DSP reset N.C. V+3D Test mode entry N.C. Component/composite SW input N.C. Command busy input Auto-sequence busy input Interrupt input 2 (AV-1) V+3D Communication response signal output to the FL controller Subcode block sync. input Test terminal (V+3D) Test terminal (V+3D) Reset input
99 GND AN0 AN1 AN2 AN3 AN4 AN5 AN6 AN7 Avref AVCC AVSS
GND LODPOS SLDPOS NAP_SW XOEM LDDEAD V+3D V+3D GND
I I I I I I I I I I I I O I O I I I O O O I O O O I I O I I O I O I GND Loading position input Slider position input N.C. NTSC/AUTO/PAL SW input
Input terminal of OEM model protection Input for LD current value display N.C. N.C. V+3D V+3D GND N.C. C2 error input Communication request input from the FL controller Serial data input (FL controller) Serial data output (FL controller) V+3D Data input of the RS-232C Data output of the RS-232C Interrupt input #0 (BY CHIP) GND Interrupt input #1 (BY CHIP) Interrupt input #0 (AV-1) Servo DSP chip select signal output N.C. AV-1 chip select signal output Wait signal input Write pulse output L GND Write pulse output H Read pulse output Over-current detection signal input RS-232C transfer permit input RS-232C transfer permit output Interrupt input 1 (AV-1) Tracking hold signal input V+3D DMA response output (BY CHIP) DMA request input (BY CHIP) DMA response output (AV-1) DMA request input (AV-1)

PB5/TIOCB4

PB6/TIOCXA4/TCLKC C2F PB7/TIOCXB4/TCLKD XRDY PB8/RxD0 PB9/TxD0 SSI SSO V+3D RXD TXD SSCK XIRQL10 GND XIRQL11 XINT0 XCS4 XCS6 XWAIT XWRL GND XWRH XRD XCURDET CTS DTR XINT1 THLD V+3D DACK0 XDREQ0
100 VCC 101 PB10/RxDPB11/TxDPB12/XIRQ4/SCKPB13/XIRQ5/SCKGND 106 PB14/XIRQPB15/XIRQPA0/XCS4/TIOCAPA1/XCS5/XRAS 110 PA2/XCS6/TIOCBXWAIT 112 XWRL 113 GND 114 XWRH 115 XRD 116 PA7/XBACK 117 PA8/XBREQ 118 PA9/XAH/XIRQOUT/ XADTRG
I/O Serial clock output (FL controller)
119 PA10/DPL/TIOCAPA11/DPH/TIOCBVCC PA12/XIRQ0/DACK0/ 122 TCLKA 123 PA13/XIRQ1/ XDREQ0/TCLKB
124 PA14/XIRQ2/XDACK1 XDACKPA15/XIRQ3/XDREQ1 XDREQAD0 D0

I/O Data bus 0

127 GND 128 ADADADADADADVCC 135 ADADADADGND 140 ADADADADVCC 145 AD15
GND D1 D2 D3 D4 D5 D6 V+3D D7 D8 D9 D10 GND D11 D12 D13 D14 V+3D D15 A0 A1 A2 GND A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 A15 A16 A17 V+3D A18 A19 A20 A21 XNMI GND XCS20 XCS23
GND I/O Data bus 1 I/O Data bus 2 I/O Data bus 3 I/O Data bus 4 I/O Data bus 5 I/O Data bus 6 V+3D I/O Data bus 7 I/O Data bus 8 I/O Data bus 9 I/O Data bus 10 GND I/O Data bus 11 I/O Data bus 12 I/O Data bus 13 I/O Data bus 14 O O O O O O O O O O O O O O O O O O O O O O I O O O O O V+3D Address bus 0 Address bus 1 Address bus 2 GND Address bus 3 Address bus 4 Address bus 5 Address bus 6 Address bus 7 Address bus 8 Address bus 9 Address bus 10 Address bus 11 Address bus 12 Address bus 13 Address bus 14 Address bus 15 Address bus 16 Address bus 17 V+3D Address bus 18 Address bus 19 Address bus 20 N.C. V+3D GND N.C. I/O Data bus 15
146 A0 (XHBS) 147 AAGND 150 AAAAAAAAAAAAAAAVCC 166 AAAAXNMI 171 GND 172 XCSXCSXCSXCSXCS2
Chip select signal output of the flash ROM Chip select signal output of the GUI ROM [OEM model] Chip select signal output of the SRAM N.C.
PM0024AF (DVDM ASSY : IC1001)
GND_00 CLK27I VDD_00 T_03 T_04 T_05 T_06 T_07 TEST_1 XVSYNC XHSYNC VCC_S00 GND_S00 XIN XOUT GND_01 VI_0 VI_1 VI_2 VI_3 VI_4 VI_5 VI_6 VI_7 T_08 GND_S01 T_09 T_10 VDD_01 OSDCK OSDHSYB OSDVSYB GND_02 CTA_0 CTA_1 CTA_2 SG16M BLD_0 BLD_1 VCC_S01 GND_S02 RMO_0 RMO_1 RMO_2 RMO_3 RMO_4 GND_AGB0 VDD_DAC2 GND_DAC1 DAOUT1

Video Encoder IC

Pin Name I/O

I/O Data input and output for SGRAM with pull-up (LSB)
I O I I I I Ground Connect to reference voltage (0V). Test mode cntrol input Connect to GND. SSG lock output System reset input L: reset Schmitt input
201 GND_T_T_SGLOCK 205 SRN 206 SCLK 207 SDATA 208 CSB
Serial clock input for microcomputer interface Lead in SDATA at rising edge. Schmitt input Serial data input for microcomputer interface Schmitt input Chip select input for microcomputer interface L: select Schmitt input
PE5185A (FLKY ASSY : IC101)

FL Control IC

P94 P93 P92 P91 P90 P81 P80 VDD P27 P26 P25 P24 P23 P22 P21 P20 RESET P74 P73 AVSS P17 P16 P15 P14 P13 P12 P11 P10 AVDD AVREF P04 XT2 VSS X1 X2 P37 P36 P35 P34 P33 NORMAL/KARA (NC) I O Microphone existence detection [RAM model] H: Microphone having (NC) O
G7 G6 G5 G4 G3 G2 G1 (5V) FLSET1 FLSET2 KEYSET (NC) XREADY SCK SO SI RESET IN (NC) (GND) (GND) (GND) KIN2 KIN1 KIN0 MS1 MS0 (5V) (5V) (GND) (NC) (GND) X1 X2

Active

FL timing output

I I O O

FL tube setting Key division number setting Communication handshaking line with system control IC L: Communication permission
I/O Communication clock output with system control IC I/O Communication data output with system control IC I I O I I I I I I I Communication data input with system control IC Reset input (Not used) Key input Inducing distinction input Model distinction input (Not used) Microcomputer clock connection L: Reset
P32 P31 P30 P03 P02 P01 P00 IC P72 P71 P70 VDD
POWER ON RESET OUT (NC) TES ON POWER LT SEL IR IC (NC) (5V) P. ON LED OEM FL OFF LED (NC) P19 P18 P17 P16 P15 P14 P13 P12 P11 P10 P9 P8 P7 -27V P6 P5 P4 P3 P2 P1 G10 G9 G8
O O O I I I I O O O O O SW 5V ON/OFF System reset output

H: ON L: Reset

Setting when system control IC is debugged STBY/POWER ON switch at the time of FL control IC standing up Communication handshaking line with system control IC Remote control signal input STANDBY LED ON/OFF OEM model distinction input FL OFF LED ON/OFF
H: At debugging L: STBY H: Communication permission
P127 P126 P125 P124 P123 P122 P121 P120 P117 P116 P115 P114 P113 P112 P111 P110 P107 P106 VLOAD P105 P104 P103 P102 P101 P100 P97 P96 P95

H: ON H: OEM H: ON

FL segment output

Input for -27V

8. PANEL FACILITIES AND SPECIFICATIONS

8.1 PANEL FACILITIES

Front Panel
(lllustration is KU/CA and LB types)
STANDBY/ON button (KU/CA and LB types only)
Press to switch the player on or to put in standby.

Remote sensor

- = ~ !
Point the remote control toward the remote sensor to operate the player.
POWER switch (Except for KU/CA and LB types )
Press to switch the player on or off.
7/0 (stop/open/close) button
Press to open and close the disc tray. Press to stop playback. Pressing once enables playback to resume from a point shortly before the location where it stopped. During playback, press twice to open the disc tray.

VIDEO ADJUST (V.ADJ) button
Various attributes of the video presentation can be adjusted to suit the program type or personal preferences. Press VIDEO ADJUST (V.ADJ) to display the on-screen options.
FUNCTION MEMORY (F.MEM) button
Press to incorporate a menu item into a shortcut list that is stored in memory and can be called up at any time.
All of the command buttons on the remote control glow in the dark for easy control of the player even in the dark. Hold the unit under a light for optimal results.

PLAY 3 button

Press to start disc playback.

STOP 7 button

Press to stop playback. Pressing once enables playback to resume from a point shortly before the location where it was stopped. Pressing twice causes the disc to return to the beginning of the disc when playback starts again.

PREVIOUS 4/NEXT buttons

During playback, press PREVIOUS 4 to go back to a previous chapter/track and NEXT to advance to the next chapter/track.

RETURN

button*

DIMMER (FL) button

Press to change the brightness of the FL display and disc illumination in four steps: maximum brightness, medium brightness, minimum brightness, and off. When the FL display is turned off, the FL OFF indicator on the front panel lights.
Use to go one menu back (current settings are maintained). Use RETURN when you do not want to change the option setting in a menu.

STEP/SLOW e/E buttons

Press STEP/SLOW E during playback to view slow playback. In pause mode, press STEP/SLOW E to advance DVDs and Video CDs frame by frame and STEP/SLOW e to back up a DVD a few frame by frame at a time.

JOG MODE indicator

Lights red when the player is in the Jog Mode.

JOG MODE (JOG) button

Press to put the player in the Jog Mode. When this mode is on, rotate MULTI DIAL clockwise to scan frame by frame in the forword direction and counterclockwise to scan frame by frame in the reverse direction.
Number buttons (1-9, 0, +10)*
Use to perform direct title and chapter/track searches, and to input numerical values.

RANDOM button

Press to play titles/chapters/tracks in random order.

PAUSE 8 button

Press to pause playback of a disc. Press again to resume playback.

LAST MEMORY button

You can resume DVD or Video CD playback from the point you last watched even if the disc is removed from the player. Press LAST MEMORY during playback to set a Last Memory point. When you want to resume playback of that disc, press LAST MEMORY in the stop mode and playback starts from the memorized point. Last Memory locations can be stored for up to 5 DVDs and 1 Video CD.

**= *~ ! *@ # $

% ^ & **
2. Confirm that the TV is responding to the programmed code.
On the remote, press the TV button. If the TV swithches on (or into standby if it was on previously), then you have the correct code. If nothing happens when you press the TV button, start again from step 1 using a different code. Some Manufacturer have several codes. Try each one until you find the one that works.

(* ) _ +

Preset Code List
Code Manufacturer PIONEER 1 RCA 1 SHARP 3 ZENITH 1 SONY TOSHIBA 1 HITACHI 1 PHILIPS PANASONIC 1 MITSUBISHI GOLDSTAR 1 GE 1 MAGNAVOX 1 JVC 1 SANYO 2 RCA 2 RCA 3 RCA 4 Code Manufacturer RCA 5 SHARP 1 ZENITH 2 SANYO 1 PANASONIC 2 GOLDSTAR 2 HITACHI 2 HITACHI 3 TOSHIBA 2 SHARP 2 GE 2 MAGNAVOX 2 TOSHIBA 3 HITACHI 4 JVC 2 FUJITSU PIONEER 2 GRANDIENTE
* These butttons are used to navigate on-screen menus. MENU displays DVD disc menu. Power switches player on or into standby. AUDIO switches audio language/channels. DISPLAY shows on-screen disc information. SETUP enters Setup menu. MULTI DIAL controls picture scanning speed/frame advance. LIGHTING press to illuminate buttons 8, 9, 10, 11, 23, 25, 26. V.ADJ (VIDEO ADJUST) press to adjust picture quality settings such as sharpness, colour balance, etc. F.MEM (FUNCTION MEMORY) displays the function memory menu. 3 (PLAY) starts/resumes playback. 7 (STOP) stops playback/scanning, etc. 4 (PREVIOUS/NEXT) skips to the previous/next title/chapter/track. Also used to navigate Video CD menus. (RETURN) returns to the previously displayed menu screen. Also displays Video CD menu. e E (STEP/SLOW) controls slowmotion/frame advance. Number buttons use to select titles/ tracks/chapters/time when searching, programming, etc. RANDOM sets the random playback mode. LAST MEMORY memorizes the current location in the DVD-video or Video CD discs loaded; starts playback from a point previously memorized. 0 (OPEN/CLOSE) opens/closes the disc tray. SUBTITLE switches the subtitle display on multi-lingual DVD discs. ANGLE switches camera angle on DVDs that have multi-angle scenes.
TOP MENU displays the top menu of a DVD disc. Joystick / ENTER button move the joystick up/down/left/right to navigate onscreen menus and displays; press to select menu items from the Setup menu and DVD disc menus. FL (DIMMER) changes the brightness of the front panel fluorescent display. Jog indicator lights when multi dial is in jog mode. JOG (JOG MODE) puts multi dial into jog mode. 8 (PAUSE) pauses/restarts playback. 1 (REV/FWD) press and hold for fast reverse/forward scanning. SEARCH MODE changes the disc search mode. C (CLEAR) clears a playlist entry; cancels repeat and random play modes. PROGRAM enters playlist programming mode. REPEAT A-B sets the repeat mode and loop points. CONDITION MEMORY memorizes the current player settings for the DVD disc loaded.

DV-37, DV-S77, DV-S737, DV-737, DV-737-K 8.2 SPECIFICATIONS

KU/CA type

Specifications
General System.. DVD system and Compact Disc digital audio system Power requirements... AC 120 V, 60 Hz Power consumption... 25 W Power consumption in standby mode. less than 1 W Weight... 6.5 kg (14 lb 6 oz) Dimensions (Not including protruding cables, etc.).. 420 (W) x 370 (D) x 128 (H) mm (16 9/16 (W) x 14 10/16 (D) x 5 1/16(W) in.) Operating temperature. +5C to +35C (+36F to +96F) Operating humidity.. 5% to 85% (no condensation) S-Video output (2 individual outputs) Y (luminance) - Output level.. 1 Vp-p (75 ) C (color) - Output level.. 286 mVp-p (75 ) Jacks... S-VIDEO jack

Accessories

Audio Cord (L=1.5m): VDE1033 White
Red Video Cord (L=1.5m): VDE1034 Yellow

Power Cord: ADG7021

Remote Control Unit: VXX2714
Video output (2 individual outputs) Output level... 1 Vp-p (75 ) Jacks... RCA jack Component video output (Y, PB, PR) Output level... Y: 1.0 Vp-p (75 ) PB, PR: 0.7 Vp-p (75 ) Jacks... RCA jacks Audio output Output level During audio output.. 200 mVrms (1 kHz, 20 dB) Number of channels... 2 Jacks... RCA jacks Digital audio characteristics Frequency response. 4 Hz to 44 kHz (DVD fs: 96 kHz) S/N ratio... 115 dB Dynamic range... 109 dB Total harmonic distortion.. 0.001% Wow and flutter... Limit of measurement (0.001% W. PEAK) or lower Digital output Optical digital output.. Optical digital jack Coaxial digital output.. RCA jack Other terminals CONTROL IN... Minijack (3.5 ) CONTROL OUT.. Minijack (3.5 ) Accessories Audio cord... 1 Video cord... 1 Power cord... 1 Remote control unit.. 1 AA (R6P) dry cell batteries... 2 Operating Instructions... 1
Dry Cell Battery (R6P,AA)
The specifications and design of this product are subject to change without notice, due to improvement.
Manufactured under license from Dolby Laboratories. Dolby and the double-D symbol are trademarks of Dolby Laboratories. Confidential unpublished works, 1992-1997 Dolby Laboratories. All rights reserved. DTS is trademarks of Digital Theater Systems, Inc.

LB, RL and RL/RD types

General System.. DVD system and Compact Disc digital audio system Power requirements Taiwan model.. AC 110 V, 60 Hz Other models.. AC 110~127 V/220~240 V, 50/60 Hz Power consumption Taiwan model... 25 W Other models.. 26 W Power consumption in standby mode. less than 1 W Weight Taiwan model... 6.8 kg Other models... 6.9 kg Dimensions (Not including protruding cables, etc.).. 420 (W) x 370 (D) x 128 (H) mm Operating temperature.. +5C to +35C (+36F to +96F) Operating humidity.. 5% to 85% (no condensation) S-Video output (2 individual outputs) Y (luminance) - Output level.. 1 Vp-p (75 ) C (color) - Output level.. 286 mVp-p (75 ) Jacks... S-VIDEO jack Video output (2 individual outputs) Output level... 1 Vp-p (75 ) Jacks... RCA jack Component video output (Y, PB, PR) Output level... Y: 1.0 Vp-p (75 ) PB, PR: 0.7 Vp-p (75 ) Jacks... RCA jacks D2 video output Output level... Y: 1.0 Vp-p (75 ) PB, PR: 0.7 Vp-p (75 ) Jacks... D terminal Audio output Output level During audio output.. 200 mVrms (1 kHz, 20 dB) Number of channels... 2 Jacks... RCA jacks Digital audio characteristics Frequency response. 4 Hz to 44 kHz (DVD fs: 96 kHz) S/N ratio... 115 dB Dynamic range... 109 dB Total harmonic distortion.. 0.001% Wow and flutter... Limit of measurement (0.001% W. PEAK) or lower Digital output Optical digital output.. Optical digital jack Coaxial digital output.. RCA jack Other terminals CONTROL IN... Minijack (3.5 ) CONTROL OUT.. Minijack (3.5 )

Other terminals

Control in... Minijack (3.5 ) Control out... Minijack (3.5 )
Audio cable... 1 Video cable... 1 Power cord.... 1 Remote control unit... 1 AA size (R6P) batteries... 2 Operating Instructions... 1 Note: The specifications and design of this product are subject to change without notice, due to improvement.

CANNINGTON

(City side of Carousel) 1334 Albany Hwy, 9356 2335
Toshiba 46 RPTV Toshiba SD1300 Toshiba 68cm 4:3 TV Thomson 44 RPTV Thomson 76cm 16:9 100Hz TV Thomson 76cm 16:9 100Hz TV with built in DVD player Yamaha RXV 2200 (Digital receiver) Yamaha RXV 430 (Digital receiver) Energy eXLS8 (Subwoofer) Harman Kardon CDR20 (CD recorder) NAD 317 (Stereo integrated amplifier) Onkyo Integra TX-DS 898 (THX digital receiver) Onkyo TX-SR500 (Digital receiver) Onkyo TX-SR600 (Digital receiver) Onkyo TX-SR700 (Digital receiver) Pioneer DV-S737 (DVD player) Wharfedale DB Dynamics 12 Subwoofer B&W CM4 (Speakers) B&W CM2 (Speakers) B&W CMC (Centre speaker) JVC 68cm 4:3 super-flat TV
$6,000 $350 $1,599 $4,999 $2,999 $3,499 $1,999 $579 $599 $999 $949 $3,999 $850 $1,150 $1,699 $1,499 $699 $2,799 $1,499 $849 $1,499
Many more specials in store!!!