Tabletop Stand: PDK-TS01
Regarding the stand pipe screw holes when the stand is used as a desktop stand Stand pipe screw holes when the stand is used as a desktop stand Specifications... Normal use Screw holes used with stand orientation. B, B' Note: Screw holes A, A', C and C' are for attaching options available separately.

C A C A

2 Hook the stand pipe holes B onto the screw heads of the installation bolts 1, then slide the stand upwards to the main plasma display until it engages the installation bolts 1 (once put together with the display, the stand will slides no more than 19 mm). 3 Pass the installation bolts 2 (M8 40) through the stand pipes and tighten the installation bolts securely with the included hexagonal wrench (holes should be used in the proper, B, B'). 4 Tighten the installation bolts 1 securely with the hexagonal wrench provided.
1. Place a sheet or protective cover to protect the display from scratches or damage. 2. Assemble only with the plasma display lying flat on a table or similar surface. Notes 3. Do not apply excessive pressure and tighten the bolts more than necessary. 4. Move the stand so that the stand screw holes and the nuts that connect the main display line up correctly. 5. The display weighs approximately 40 kilograms (88 lb.) and has little depth, making the display very unstable. For this reason, at least two people are required for setup and installation.
Installation bolts 2 (M8 40)

Slide the stand

Table top stand
2) Instructions for using the main display packing material as a stand for the working on the display Main plasma display packaging setup

Outer box

Inner box frame

Mirror mat Pad

Plasma display
1 Construct the stand for the plasma display using the inner box frame and pads shown in the figure above (all pads are identical).
2 Set the plasma display down on the pads as shown in the figure below.

Mirror mat

Inner box frame topped by two pads
3 Follow the instructions in Steps 1-4 in "Normal Installation" to attach the stand to the plasma display.
After assembling, connect the stand to the floor to prevent from falling over. 7 Stabilizing to the floor Use screws (sold separately) to attach and stabilize the stand. 7 How to use the stabilization bolts 1. Attach the included bolts that prevent the display from falling over. 2. Stabilize the display by connecting to a wall or standing beam with a strong cord. (Repeat the same steps in the laterally direction to stabilize the assembly to the left and right.) Use cord and hooks that are available on the market (sold separately).
PDP Bracket: PDK-5005 4.6 PDP Bracket: PDK-5005

4.6.1 Specifications

External Dimensions. 1218 (W) 714 (H) 148.5 (D) (47-15/16 (W) 28-1/8 (H) 5-27/32 (D) in.) (when mounted to the display) Weight.. 4.1 kg (9.0 lbs.) (mounting hardware only) 43.0 kg (94.8 lbs.) (mounting hardware and plasma display <when using PDP-503CMX or PDP-503MXE>) Material.. steel pipe for general structure (STK-MR) Finish.. Semi-matte black paint (Original Pioneer color) Package dimensions.. 850 (W) 110 (H) 130 (D)mm (33-15/32 (W) 4-11/32 (H) 5-1/8 (D) in.) Package weight.. 5.0 kg (11.0 lbs.) Accessories Vertical frame.. 2 Horizontal frame.. 2 Monitor mount bolt.. 4 Plus/minus screw with washer (M5 x 50). 8 Special eye bolt (M6 30).. 4 Spring washer nut for M8.. 8 Hexagonal nut for M8 (M10 85).. 8 Large flat washer for M8.. 8 Small washer for M8.. 4 Operating instructions... 1 Mount contractor contract form. 1 The appropriate types of screws and other mounting hardware will depend on the strength and composition of the ceiling and walls. Prepare them separately. For the operating temperature restrictions of the unit please refer to the Special Installation section

PDP Bracket: PDK-5005

4.6.2 External Dimensions
(Units: mm) The mounting format is symmetrical from left to right and from top to bottom.
(Special eye bolt mounting pitch) 455 20

700 528

8- 9 148.5

4.6.3 Assembly Procedure

1 Temporarily fasten the vertical a and horizontal b frames using all of the M5 plus/minus screws with washers e.
a c h c h a g e j e g b h c g g j e b e
2 Attach the special eye bolts c to the spring washers h, and insert them into the appropriate holes. Secure the small flat washers j and nuts g. (For additional safety, use double nuts.)
Spring washer hexagonal nut ( 4) Insofar as possible, insert the bolt so that the nut goes all the way to its base.
g j g 2. After passing the bolt through, secure it with the small flat washer and nut. 3. Tighten the nuts with spanners.

View from below

1. Attach the special eye bolts together with the M8 nuts to the main unit.

4. For additional safety, use double nuts. (Tighten the two nuts against each other.)

CAUTION

Never use special eye bolts except in the designated locations. If they are used on the plasma display itself, internal damage may result.
3 Place the bracket on a level table or platform for the final tightening of the bolts.
The tightening the screws on the vertical and horizontal frames should be performed on a level table, as illustrated, and after the CAUTION positions of the holes have been aligned.

<Wrong>

Table, etc. If placed in this position, it will be difficult to align the holes.
4 Place the plasma display face down on a secure table, as shown in the illustration, in such a way as to prevent it from falling or getting scratched.

PDP bracket h h

5 Place a large flat washer i on each of the designated holes. Tighten well the monitor mounting bolts f from above. 6 Place another large flat washer of each monitor mounting bolts. On top of these, mount the assembled PDP bracket.
Washers must be used. If the number and location of washers is incorrect, warping of the display unit may result.
7 As the last step secure the M8 spring nuts h.

4.6.4 An example of use

The unit can be mounted to any of Pioneer's mounting hardware (PDK-5012) while it is attached to the PDP bracket. As illustrated, the bracket can be used as a handle for moving and installation.
Wall-mounted tiltable plasma display hardware PDK-5011 4.7 Wall-mounted tiltable plasma display hardware PDK-5011

4.7.1 Specifications

External dimensions.. 1218 (W) 714 (H) 143 (D) mm (47-15/16 (W) 28-1/8 (H) 5-5/8 (D) in.) (when using PDP-503CMX or PDP-503MXE) Weight.. 13.8 kg (30.4 lbs.) (mounting hardware only) 52.7 kg (116.2 lbs.) (mounting hardware and plasma display <when using PDP-503CMX or PDP-503MXE>) Materials. General structural steel tubes (STK-MR) Finish.. Semi-matte black paint on rear (Original Pioneer color) Dimensions of packaging. 890 (W) 120 (H) 700 (D) mm (35-1/32 (W) 4-23/32 (H) 27-9/16 (D) in.) Package weight.. 18.0 kg (39.7 lbs.) Layers of packing.. 20 layers Components Hung on wall unit.. 1 Bolt M8... 6 Hexagonal wrench... 1 Operating Temperature Restrictions Ambient temperature: 0 to 40 C Operating Temperature Restrictions for Upside-Down Installations * Upside-Down Installation is unavailable with the PDK-5011. Operating temperature restrictions for when the speaker system (PDP-S05-LR) is attached. Ambient temperature: 0 to 40 C In wall-mounting installation allow adequate space (a clearance of 300 mm or more) above and below the monitor set, as well as on the right and the left.
Wall-mounted tiltable plasma display hardware PDK-5011
4.7.2 External Dimensions

(Units: mm)

( 258 )

( 143 ) 45

714 C.L. (center of the display) ( 125 ) 35

Plasma Display Ceiling Suspension Hardware: PDK-5012
4.8.2 External Dimensions

(Unit: mm)

This diagram indicates the dimensions of the PDP-503CMX or PDP-503MXE plasma display after installation.

200 300

4-13.5X22

216 123

800 980

146 67

496 (530) 1218

R 67 2

This circle shows the path that the outermost part of the plasma display follows when it is rotated about a vertical axis after having been titled sideways by 25.
4.8.3 Assembling and Installing the mounting hardware and mounting the plasma display
1) Preparations You will need the following tools. Make sure you have them at hand before beginning work. Plus driver Hexagonal wrench (subtense 5 mm, for M6 bolts) Hexagonal wrench (subtense 6 mm, for M8 bolts) You'll also need tools for ceiling work. 2) Installing the mounting hardware Select the installation site, then apply the supplied pattern to the ceiling, drill the holes, and mount the ceiling suspension hardware. The appropriate types of screws and other display/mounting hardware will depend on the strength and composition of the particular ceiling. Firmly tight all bolts. After mounting the mounting hardware but before mounting the plasma display, confirm the strength of the mount portion of the ceiling. For additional safety, use the holes in the ceiling suspension hardware as shown. [Use parts strong enough to support the weight of the display.]
Anchor Ceiling suspension hardware Foundation ceiling
Example. Securing to a foundation ceiling with shackle and safety wire.

Safety wire

Shackle
(NOTE) Safety wires serve as important backups in keeping the unit securely mounted.

4.8.4 Assembly procedure

1 Attach the PDP bracket to the plasma display. Warning Cover the display with a sheet or similar protective material to protect it from scratches or other damage. Be careful that the PDP bracket is not upside down.
PDP bracket Top side of plasma display
3 Attach the plasma display to the hanger.

Hanger

4 Screw the plasma display to the hanger (at 4 locations).
2 Fix the plasma display to the PDP bracket with screws (6 locations). Warning Be sure to use the holes (hole positions on the diagram) shown on [50] to attach the PDP503CMX or PDP503MXE.

Top side of plasma displa Hexagonal bolts (6 holes shown on [50])

4.8.5 Angle setup

Left-right Adjustment You can adjust it 45 to the left or right by loosening the top screw. Set the desired angle, then tighten the screw. Vertical Adjustment You can adjust its vertical angle by loosening the screws on the left and right sides. (You can adjust it a maximum of 25 downwards from the vertical position.)
Set it to the desired angles while supporting the plasma display and retighten the loosened screws on the left and right sides. The hole on the side indicates the angle. (5 units).
Detailed Angle Standard Diagram
Connecting cable (when coming out of the top of the supporting column)
Connecting cable (when coming out of the hole)
To the connector on the plasma display
Wall-mounted type tiltable fixed plasma display hardware PDK-5013 4.9 Wall-mounted type tiltable fixed plasma display hardware PDK-5013

4.9.1 Specifications

External dimensions.. 1218 (W) 714 (H) 130 (D) mm (47-15/16 (W) 28-1/8 (H) 5-1/8 (D) in.) (when using PDP-503CMX or PDP-503MXE) Weight.. 8.9 kg (19.6 lbs.) (mounting hardware only) 47.8 kg (105.4 lbs.) (mounting hardware and plasma display <when using PDP-503CMX or PDP-503MXE>) Materials. General structural steel tubes (STK-MR) Finish.. Semi-matte black paint on rear (Original Pioneer color) Dimensions of packaging. 1070 (W) 90 (H) 590 (D) mm (42-1/8 (W) 3-17/32 (H) 23-7/32 (D) in.) Package weight.. 12.0 kg (26.5 lbs.) Layers of packing.. 30 layers Components Hung on wall unit.. 1 Bolt M8... 6 Hexagonal wrench (Opposite side 6 mm for M8 use).. 1 Stencil... 1 Operating Temperature Restrictions Ambient temperature: 0 to 40 C Operating Temperature Restrictions for Upside-Down Installations * Upside-Down Installation is unavailable with the PDK-5013. Operating temperature restrictions for when the speaker system (PDP-S05-LR) is attached. Ambient temperature: 0 to 40 C In wall-mounting installation allow adequate space (a clearance of 300 mm or more) above and below the monitor set, as well as on the right and the left.

Wall-mounted type tiltable fixed plasma display hardware PDK-5013
4.9.2 External Dimensions

496 455

714 ( 425)

6-6 x 63

C.L. (Center of the display)

496 682.32

17-6 x 120
4.9.3 Assembling the mounting hardware and mounting the display
1 Remove the screws (2 locations) from the bottom of the hung on wall unit with a Phillips head (+) screw driver. 3 Attach the PDP side hardware to the plasma display. Warning Cover the display with a sheet or similar protective material to protect it from scratches or other damage. Be sure to attach it on top of a flat table or similar surface.
PDP side hardware Top side of plasma display

Pin Screws M6

2 Remove the hardware on the wall side and the hardware on the PDP side. 1. Push the pin on the bottom side and pull out the bottom side of the PDP side hardware. 2. Lift up and remove the PDP side hardware.
4 Fix the plasma display to the PDP side hardware with bolt M8 (6 locations).
5 Attach the wall side hardware to the wall. Fix the unit with screws (at 4 or more locations) symmetrically on the left and right side. Because the screws and bolts used to do this are different according to the wall strength and wall material, purchase suitable screws and bolts separately. Warning Check the strength of the wall and beams before installing the display.
7 Fix the bottom of the hardware with the screws removed at step 1 (one on the left and one on the right).
6 Attach the hook on the PDP side hardware to the wall side hardware. While it is hooked, the pin on the bottom side does not go in, so push the pin in.
PDP side hardware Pin Push
Mobile Cart: PDK-5014 4.10 Mobile Cart: PDK-5014

4.10.1 Specifications

External dimensions.. 1218 (W) 1707 (H) 720 (D) mm (47-15/16 (W) 67-7/32 (H) 28-11/32 (D) in.) (when using PDP-503CMX or PDP-503MXE) Weight.. 43.0 kg (94.8 lbs.) (stand only) 81.9 kg (180.6 lbs.) (stand and plasma display <when using PDP-503CMX or PDP-503MXE>) Materials. STKM (steel pipe) SPCC and SS41 Finish.. Melamine baking finish (silver metallic) Dimensions of packaging. 1465 (W) 200 (H) 790 (D) mm (67-11/16 (W) 7-7/8 (H) 31-3/32 (D) in.) (bracket, display stand section) 810 (W) 295 (H) 810 (D) mm (31-7/8 (W) 11-15/16 (H) 31-7/8 (D) in.) (stand shelf, leg section) Package weight.. 38 kg (83.8 lbs.) (bracket, display stand section) 21 kg (46.3 lbs.) (stand shelf, leg section) Layers of packing.. 10 layers Components Display stand.. 1 Rear cover... 1 Leg base.. 1 Bracket... 1 Stand shelf... 1 Hexagonal bored bolts (M8 20).. 10 Hexagonal bored bolts (M8 60). 4 Hexagonal wrench... 1 Washer... 4 Plate spring washer.. 4 Operating Temperature Restrictions Ambient Temperature: 0 to 40 C Operating temperature restrictions for when the speaker system (PDP-S05-LR) is attached. Ambient temperature: 0 to 40 C

132.3 919.5 (Panel) 59 220
312.(673) 666.1218 (723) 496

630 (Stand shelf)

4.10.2 External Dimensions

98.555 337

55 32.143.(Stand shelf) 1350 (Center of the display screen when it is installed at the upper position) 1170 (Center of the display screen when it is installed at the lower position) 770 (Stand shelf installed at the highest position) 730 (Stand shelf installation spacing 40 mm)

(Tilt angle)

330 (Stand shelf installed at the lowest position) 60

Mobile Cart: PDK-5014

22 773.128.5 1084.1518.5

180 180

4.10.3 Disassembling the display stand
1 Remove the screws (four locations on the left and right sides) and take off the bracket. For packing reasons, the bracket is installed at a location that is different from the location where it is usually installed when it is used. Screws
Do not take out the screws. Bracket

2 Remove the rear cover.

Screws
Loosen the finger screws.

Rear cover

4.10.4 How to install
In order to ensure safety during installation, always be sure to work together with more than two persons. 1 Assemble the unit Attach the leg base to the display stand using the hexagonal bored bolts (M8 60) so that the rear label faces towards the back casters as the figure. Note: In order to ensure safe installation, always be sure to alternately tighten each bolt two times or more until they are firmly fixed in place.

Label Display stand

Leg base
Washer Plate spring washer
Hexagonal bored bolts (M8 60)
Back casters Support caster
2 Attaching bracket bolts to display stand Attach the hexagonal bored bolts (M8 20) to the display stand as the figure, being sure to leave a space of 5 to 6 millimeters when doing so. (Note that these bolts may be attached at two different levels to allow a distance of 1350 mm or 1170 mm from the floor to the center of the display panel.) Note: The bracket bolts may not be screwed into the third set of screw holes from the top, as these screw holes are used in Step 4 below.

Display stand

Hexagonal bored bolts (M8 20) 5 to 6 mm
3 Attaching bracket to plasma display Using the hexagonal bored bolts (M8 20), attach the bracket to the rear of the plasma display by screwing the bolts into the screw holes as the figure. Note 1: The plasma display should be placed on a blanket or other soft surface so as to avoid scratching or otherwise damaging the surface of the display. Note 2: In order to ensure safe installation, always be sure to alternately tighten each bolt two times or more until they are firmly fixed in place.

Hexagonal bored bolts (M8 20)

Bracket

4 Attaching a panel to the stand once the bracket has been attached 1. Fix the holes on the protruding portion of the bracket onto the left and right bolts attached to the display stand. 2. Using two hexagonal bored bolts (M8 x 20), fix the bracket to the left and right sides of the display stand by inserting and screwing in the bolts into the screw holes located at the bottom of the protruding part of the bracket and the screw holes of the display stand. 3. Screw the bolts of the protruding portion of the bracket firmly into place. Note: In order to ensure safe installation, always be sure to alternately tighten each bolt two times or more until they are firmly fixed in place. [Adjusting the angle of the plasma display screen]
When you want the screen to be easier to see, you can angle it forwards by altering the bracket attachment locations. (5)

Precaution:

To safely attach the brackets to the support columns, be sure to always have two people do this task as shown in the drawing. 0 5
5 Attaching the stand shelf to the display stand Hold the stand shelf at a diagonal to the display stand and insert the upper portion of the hooked end of the shelf brackets into the slits located on the display stand before then returning the shelf to a horizontal position to fix it into place.
Insert the hook securely into the slit.
6 Adjusting the support casterWhen the mobile cart has been placed into position, be sure to adjust the support caster to fix into place. 1. Turn the support caster in the direction indicated by the arrow until the bottom of the caster touches the floor. 2. Turn the nut at the top of the caster in the direction indicated by the arrow to fix the caster into place. 8 Attach the rear cover.Attach the rear cover and fix it in place by tightening the finger screws. Be careful not to catch the cable in the rear cover.

Support caster nut

Bottom of support caster

Finger screw

7 Hang the cords on the hooks on the back of the support columns.
Cable Cover: PDA-P01 4.11 Cable Cover: PDA-P01

4.11.1 Specifications

External dimensions.. 754 (W) 123.9 (H) 45.5 (D) mm (29-11/16 (W) 1-13/16 (H) 4-7/8 (D) in.) Weight.. 225 g (0.50 lbs.) Materials. ABS Dimensions of packaging. 771 (W) 59 (H) 151 (D) mm (30-11/32 (W) 2-5/16 (H) 5-15/16 (D) in.) Package weight.. 0.7 kg (1.5 lbs.) Accessories Cable cover.. 1 Clips... 4 Operating instructions.. 1

4.11.2 External Dimensions

4.11.3 Cautions

1. This cable cover was exclusively designed for plasma displays produced by PIONEER. 2. This product is important for the assembled displays external appearance. The cover keeps cables organized when numerous input and output cables are connected.
4.11.4 Cable lead-in locations
When the cable cover is attached to the plasma display, you can lead in the cable from a total of 5 locations: 1 on the front, 2 on the sides, and 2 on the bottom. Choose the cable lead-in location suitable for the way the way the display is used.

Lead-in from the front

Lead in from the side

Lead in from the bottom

Front view

Side view

Bottom view

Cable Cover: PDA-P01

4.11.5 How to install
1 Insert the included clips in the four corresponding holes in the rear of the plasma display housing. Be sure to insert the clip all the way to the bottom. (Note! Once inserted, these clips cannot be removed. Additionally, make sure the clips are not inserted in the ventilation holes.)

Ventilation holes

Only four clip holes are arranged along this line. Holes for attaching the clips
2 Connect the cables. 3 After the cables are in place, attach the cable cover. First slide the cable cover onto the rear case, then snap the notches onto the stems of the four clips.
Seven square holes are evenly spaced in a line at the bottom of the rear panel. Clips attached to the plasma display Square holes

Cable cover

4 Carefully arrange the cables, then snap the cable cover shut into the seven square holes at the bottom of the rear panel.
Speaker System: PDP-S05-LR 4.12 Speaker System: PDP-S05-LR

4.12.1 Specifications

External dimensions.. 74 (W) 714 (H) 101 (D) mm (2-29/32 (W) 28-1/8 (H) 3-31/32 (D) in.) 1368 (W) 714 (H) 103 (D) mm (53-27/32 (W) 28-1/8 (H) 4-1/16 (D) in.) (plasma display monitor when using PDP-503CMX or PDP-503MXE) Weight.. 1.8 kg (4.0 lbs.) 42.5 kg (93.7 lbs.) (plasma display monitor when using PDP-503CMX or PDP-503MXE) Dimensions of packaging. 778 (W) 168 (H) 318 (D) mm (30-5/8 (W) 6-5/8 (H) 12-17/32 (D) in.) Package weight.. 5.0 kg (11.0 lbs.) Cabinet.. Enclosed type, antimagnetic design Used speakers (two-way method): Woofer (for low tones). Oval cone type Tweeter (for high tones). 2.5 cm dome type Nominal impedance.. 8 Frequency Range.. 50 to 20,000 Hz Sensitivity.. 82 dB/W (at 1 m distance) Permissible input: Max. input.. 12 W Rated input. 4 W Crossover frequency.. 3 kHz Accessory parts (for 2 speakers) Speaker cable.. 2 Flat countersunk head screw.. 4 Hexagon socket head screw. 4 Mounting tool.. 1 Washer M8 (25).. 2 Speaker mounting fittings.. 2 Mounting plate (for left side).. x 1 Mounting plate (for right side).. x 1 Warranty card.. x 1 Operating Instructions... x 1 Note After this unit has been installed on the plasma display, you cant use the display operation panel.

Cautions

The color may be irregular if there is a CRT type PC monitor close to it. To prevent this, keep the speaker separated from a PC monitor.
Speaker System: PDP-S05-LR
4.12.2 External Dimensions (plasma display monitor when using PDP-503CMX or PDP-503MXE)
Center of gravity (Units: mm)

15.5 294.1 714

1368 1218
4.12.3 Installation on the PDP-503CMX or PDP-503MXE
1) Installing procedure Perform installation according to the following steps (1) to (3). Note: After this unit has been installed on the plasma display, you cant use the display operation panel. Please use the remote control supplied with the display. (1) Attach the mounting plates to this unit As in the illustration below (right speaker only), when looking from the rear, attach the right mounting plate to the right hand side of the right speaker. For the left speaker, attach the left mounting plate to ther left hand side.
Adjust the mounting plate to about 0.5 cm below the upper edge of the speaker. Seal Mounting plate
(3) Install this unit on the display side Install the unit marked "RIGHT" on the right side of the display.
Hexagon socket head screw
Seal Mounting plate 1 Match the speakers and the mounting plates so that the correct combination of left and right is obtained. 2 Peel the seals from the adhesive surfaces of the mounting plates. 3 Confirm the installation position and attach the mounting plate to the inside of the speaker. Seal
Install the unit marked "LEFT" on the left side of the display.
(2) Install the mounting fittings on this unit The illustration shows an example for this unit (right side).
Mounting plate For top side
Flat countersunk head screw
1 The top side fittings are different for the right and the left side, and they must be matched correctly. 2 Install the mounting fittings with bolts at the positions shown in the figure on the left.
1 Check the indications LEFT and RIGHT at the rear of the speakers, observe the indication "UP", and fasten the upper mounting fitting provisionally to the display. Then install the lower fitting on the display. 2 Adjust the position so that the gap between the speaker and the display is uniform, and then tighten the screws firmly. When the display is to be moved after speaker installation, do not hold the display by the speakers. Hold the bottom of the display to move it. Note

For bottom

2) Connection to a stereo amplifier 1. Switch off the power of the amplifier. 2. Connect the input terminals of the speaker system and the speaker output terminals of the stereo amplifier with the accessory speaker cable. The polarity of the input terminals is plus for the red terminal (the terminal on the right side in the following figure) and minus for the black terminal (the terminal on the left side in the following figure).

1. Remove the insulation and twist the core ends together. 2. Push the lever, insert the cable into the hole, and release the lever. terminal
3) Installation to commercial mounting fittings This unit includes M8 (25) washers for installation on commercial mounting fittings.

Washer M8 ( 25)

Installation is made by two-point fixing at the top side mounting holes for commercial mounting fittings. As these two mounting holes are not at the same level, washers are used to compensate for this difference.

terminal

4) Cabinet maintenance
To the terminal To the terminal
Use a polishing cloth or dry cloth to wipe off dust and dirt. When the cabinet is very dirty, wipe with a soft cloth moistened with water-diluted cleanser; then wipe again with a dry cloth. Do not use furniture wax or cleaners. They may damage the surface of the cabinet. Never use thinner, benzine, insecticide sprays and other chemicals on or near the cabinets, since these will corrode the surfaces. When a chemical cloth is used, read the cautions for the chemical cloth carefully.
(Speaker output terminals of the stereo amplifier) After connection to the terminals, pull lightly on the cable to confirm that the tips of the cable are connected positively to the terminals. An imperfect connection can cause sound interruptions and noise. When cable cores stick out and and lines are short-circuited, an excessive load will be applied to the stereo amplifier and the operation will stop or trouble will be caused. When the polarity is reversed for one speaker (left or right) at the time of connection to the stereo amplifier, the bass reproduction will be reduced, the sound positioning will be lost, and a correct stereo effect will not be obtained.
Before Beginning Adjustments
5.1 Before Beginning Adjustments
You can make adjustments to the unit in the following ways: With the operating panel of the main unit With the remote control unit With a PC (through RS-232C) Make sure you've thoroughly read and understood the following before making any adjustments. Items that apply only when the PDA-5002 is installed are marked with a star #.

5.1.1 Operating mode

The system has the following four major operating modes:

Power Standby Status

STANDBY/ON <PON> <POF>

(NOTE)

1 Normal Operating Mode

<AJY> <AJN>

STANDBY/ON

2 Menu Mode

3 Integrator Mode
4 RS-232C Adjustment Mode
indicates operating mode and status. < indicates button operations on the remote control or on the operating panel of main unit. > indicates RS-232C command operations.
(NOTE) Refer to 5.4.1, About the integrator mode. 1 Normal Operating Mode Intended for video playback, this mode enables the following basic operations: Switching to STANDBY status (POWER OFF) Switching to power standby status Screen-size switching Volume adjustment/muting (remote control only) AUTO SET UP (only when PC signals are input) POINT ZOOM (only when PC signals are input/only remote control) Moving to the various adjustment modes such as menu mode. Additionally, normal operating mode also enables some of the RS-232C commands controls (as discussed in 5.5.4, List of RS-232C commands). 2 Menu Mode This mode is for adjusting the resolution and the image position and for carrying out the various other settings. Refer to 5.3, Menu Mode, for further details. This mode allows you to change adjustment data within certain limits on the basis of values adjusted in integrator or RS-232C adjustment modes (discussed later). Refer to 5.3, Menu Mode, for further details.
3 Integrator Mode This mode provides adjustment functions for the integrator. White balance adjustment and various other settings are available in addition to those in the Menu mode. Refer to 5.4, Integrator Mode for further details. 4 RS-232C Adjustment Mode This mode enables various adjustments and settings using a PC. Some adjustment items are available only in this mode. CAUTION When adjustment/setting has been made under this mode, enter ID first before other any other actions.
Refer to 5.5, RS-232C Adjustment Mode, for further details.
5.1.2 Combination use of remote control unit, operating panel and PC
The remote control and the operating panel of the main unit may be used together. (Example) You can enter the Menu mode through the operating panel of the main unit, then make adjustments using the remote. Depending on which has transmitted the more recent command, either the remote, the operating panel of the main unit, or the RS-232C may originate the command currently in effect. (Example) Operation 1 Press the MENU button on the remote control (or on the operating panel of the main unit). = Action Enters Menu mode. At this time, the only available RS-232C commands are: <AJY> <POF> 2 Now, issue an <AJY> command from a PC. = Menu mode is disabled, and RS-232C adjustment mode is activated. At this time, only the following options are available from the remote control (or the operating panel of the main unit): Power switch MENU button KEY LOCK/UNLOCK button (NOTE) The remote does not have a KEY LOCK/ UNLOCK button.

PC signal compatibilty table (INPUT5) #
Resolution (Dot x Line) 640xx600 Refresh rate Vertical 60Hz 56Hz 60Hz 60Hz 60Hz 60Hz 56Hz 60Hz 60Hz 60Hz Horizontal 31.5kHz 640x480 35.1kHz 37.9kHz 31.7kHz 48.4kHz 1024x768 1152x864 1280x768 53.7kHz 1024x768 45.1kHz 48.4kHz 60.0kHz 64.0kHz 960x768 1280x768 1280x768 1280x768 1024x768 1280x1024 1280x768 1280x768 1280x768 800x600 852x480 1024x768 1024x768 1280x768 1280x768 1024x768 1280x768 DOT BY DOT Screen size (Dot x line) Remarks 4:3 FULL PARTIAL

852x480

: Optimal picture. Adjustment of picture position may be necessary. : Picture will be enlarged but some fine detail will be hard to see. : Simple reproduction. Fine detail will not be reproduced. Screen size will be displayed as ~ (TYPE). : Not available.

[503CMX/503MXE : 433CMX/433MXE] Wall-mounted type tiltable fixed plasma display hardware PDK-5013 Wall-mounted type tiltable fixed plasma display hardware PDK-5013

Specifications

External dimensions.. 1218 (W) 714 (H) 130 (D) mm (47-15/16 (W) 28-1/8 (H) 5-1/8 (D) in.) (when using PDP-503CMX or PDP-503MXE) 1070 (W) 630 (H) 130 (D) mm (42-1/8 (W) 24-13/16 (H) 5-1/8 (D) in.) (when using PDP-433CMX or PDP-433MXE) Weight.. 8.9 kg (19.6 lbs.) (mounting hardware only) 47.8 kg (105.4 lbs.) (mounting hardware and plasma display monitor <when using PDP-503CMX or PDP-503MXE>) 40.4 kg (88.2 lbs.) (mounting hardware and plasma display monitor <when using PDP-433CMX or PDP-433MXE>) Materials. SPHC Finish.. Semi-matte black paint on rear (Original Pioneer color) Dimensions of packaging. 1070 (W) 90 (H) 590 (D) mm (42-1/8 (W) 3-17/32 (H) 23-7/32 (D) in.) Package weight.. 12.0 kg (26.5 lbs.) Layers of packing.. 30 layers Components Hung on wall unit.. 1 Bolt M8... 6 Hexagonal wrench (Opposite side 6 mm for M8 use).. 1 Stencil... 1 Operating Temperature Restrictions Ambient temperature: 0 to 40 C Operating Temperature Restrictions for Upside-Down Installations * Upside-Down Installation is unavailable with the PDK-5013. Operating temperature restrictions for when the speaker system (PDP-S05-LR, PDP-S07-LR) is attached. Ambient temperature: 0 to 40 C
In wall-mounting installation allow adequate space (a clearance of 300 mm or more) above and below the monitor set, as well as on the right and the left.
[503CMX/503MXE : 433CMX/433MXE] Wall-mounted type tiltable fixed plasma display hardware PDK-5013
External Dimensions 7 When using plasma display monitor PDP-503CMX or PDP-503MXE

(Unit: mm)

455 120

714 (425)

6-6 x 63
Center line (Center of the display)
C.L. (Center of the display)

496 682.1218

17-6 x 120
7 When using plasma display monitor PDP-433CMX or PDP-433MXE

496 455

630 425

6-6x63

496 682.1070

17-6x120