www.pioneerelectronics.com

OPERATING GUIDE

S-FCRW2500

WHAT'S IN THE BOX

SPEAKER SYSTEM

Front speakers x 2

Center speaker x 1

Surround speakers x 2

Speaker cord

Non-skid pads

Brackets x 4

SUBWOOFER

Screws x 4

Operating guide

IMPORTANT:
The serial number for this equipment is located on the rear of the subwoofer. Please write this serial number on the warranty page and keep it in a secure area for future reference.
Do not place anything on top of the cabinet. Do not spill liquid on the cabinet. Place the subwoofer at least 8 inches from any wall or curtain in order to avoid heat build-up. The subwoofer is not magnetically shielded and so should not be placed near a TV or monitor. Magnetic storage media (such as floppy discs and tape or video cassettes) should also not be kept close to the subwoofer.

BEFORE USE

Thank you for buying this Pioneer product. Please read through this operating guide before using your speaker system to optimize performance.
FRONT / CENTER / SURROUND SPEAKERS
In order to prevent damage to the speaker system resulting from input overload, please observe the following precautions: Do not supply signal to the speaker system in excess of the maximum permissible input. When connecting or disconnecting cables, be sure amplifier power is OFF. Do not use excessive amplifier volume if using a tone control to emphasize high or low frequencies.

CAUTION:

Do not connect any of the supplied speakers to any other amplifier. This may result in malfunction or fire. Do not fix the subwoofer and center speaker to the wall or ceiling; they could cause injury if they fell. Pioneer will not be responsible for any accidents or damage that may result from improper installation.

INSTALLATION PRECAUTIONS

Do not install these units near a stove or other heating appliance, or put them in a place exposed to the sun. Such locations may cause the cabinet to change color and the speaker system to break down. The front, center and surround speakers supplied with this system are magnetically shielded. However, placing them extremely close to a television may result in color distortion on the screen. If this happens, move the speakers a little further away and switch off the television for 15-30 minutes.

WARNING:

Handling the cord on this product or cords associated with accessories sold with the product will expose you to lead, a chemical known to the State of California and other governmental entities to cause cancer and birth defects or other reproductive harm. WASH HANDS AFTER HANDLING.

SRD1283A.pm5

04.12.28, 1:43 PM

CONNECTING YOUR SYSTEM

PLACEMENT AND FINE TUNING
Sound spreads in all directions in the very low frequency range. Human hearing cannot easily detect the source of very low frequencies. Be sure to provide a space of at least 8 inches (20cm) between the rear of the subwoofer and the nearest wall.
Make sure all equipment is turned off before making any connections.
FRONT / CENTER / SURROUND / SUBWOOFER SPEAKERS
Correct wiring of your loudspeakers is essential for achieving the best sound quality. Be careful to ensure proper polarity of connection.

FRONT SPEAKERS

For best results the loudspeaker should be positioned near ear level and the loudspeakers separated a distance approximately equal to the listening distance. Angling the loudspeakers inward towards the listener will improve the image stability for non-central listeners. Close proximity to a side or rear wall will enhance the midbass performance, although too close (particularly a corner location) and the bass may be unnaturally high and image performance may be degraded.
Twist and pull off the protective shields on each wire.

CENTER SPEAKER

Connect to the speaker terminals on the rear of the receiver.
Match the colored wire with the color-coded label (above the tabs), then insert the colored wire into the red (+) tab and the other wire with the black () tab.
The loudspeaker should be positioned below the TV. For best results align the front of the loudspeaker with the front of the TV. If the loudspeaker is placed under the TV and very close to the floor, then tilting upwards may be beneficial.

SURROUND SPEAKERS

For best results the loudspeakers should be positioned at or above ear level. Depending upon your room layout and preferences, the left and right rear speakers should be positioned on the side walls just the rear of the listening position, or on the walls. Place the rear center speaker directly behind the listening position for best performance.

CENTER SPEAKER ONLY

Connect the speaker cords to the input terminals at the rear of center speaker. Match the colored wire with the color-coded label (above the tabs), then insert the colored wire into the red (+) tab and the other wire with the black () tab. red (+) black () Green Colored marker

Standard surround setup

This is a standard multichannel surround soundspeaker setup for optimal 5.1 channel home theatre sound.
If the subwoofer is placed on a hard floor, such as wood or tile, place four non-skid pads (large) on the bottom surface of the subwoofer.

Front left

Center

Front right

Subwoofer

Listening position

Surround left

Surround right

CABINET MAINTENANCE
Use a polishing cloth or dry cloth to wipe off dust and dirt. When the cabinet is very dirty, clean with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and then wipe again with a dry cloth. Do not use furniture wax or cleaners. Never use thinners, benzine, insecticide sprays and other chemicals on or near the cabinets, since these will corrode the surfaces.
If you have connected to the SX-315 and the above speaker placement isn't possible, you can select the FRONT SURROUND MODE on the receiver with the following speaker placement: Place the surround speakers to the side of the front speakers and turn them towards the closest wall (right or left).

NON-SKID PADS

If the front, center and surround speakers are placed on a hard surface, such as wood or tile place four non-skid pads (small) on the bottom flat surface of the speakers.
The front speakers are equipped with a protection device to protect the transducers from extreme conditions. Under these conditions the protection device will activate and stop the speaker from producing sound. If this happens turn the volume down to resume normal speaker output.

TROUBLESHOOTING

SYMPTOM 1. No sound PROBABLE CAUSE Bad speaker wire or connection Receiver is off Volume control is at zero REMEDY Connect correctly or replace wire Turn on receiver Slowly turn up volume Turn down the amplifiers output level (volume, bass control, bass boost) to lower the level. Turn the volume down to resume normal speaker output.

2. Sound is distorted

Extreme signal condition
3. Front speakers stop producing sound suddenly
Extreme signal condition for extended period of time

SPECIFICATIONS

FRONT / SURROUND SPEAKERS
Enclosure.. Closed-box bookshelf type (magnetically shielded) System.. 7.7 cm 1-way system Speakers.. 7.7 cm cone type Nominal impedance... 6 Frequency range.. 85 Hz to 20 kHz Dimensions.. 105 (W) x 115 (H) x 114 (D) mm 4 1/8 (W) x 4 1/2 (H) x 4 1/2 (D) in. Weight FRONT SPEAKER.. 0.6 kg/ 1 lb. 5 oz SURROUND SPEAKER.. 0.66 kg/ 1 lb. 7 oz

Enclosure.. Bass-reflex floor type System... 16 cm 1-way system Speaker... 16 cm cone type Nominal impedance.. 6 Frequency range... 30 Hz to 2.5 kHz Dimensions.. 190 (W) x 360 (H) x 317 (D) mm 7 1/2 (W) x 14 3/16 (H) x 12 1/2 (D) in. Weight... 4.2 kg/ 9 lb. 4 oz
Enclosure... Closed-box bookshelf type (magnetically shielded) System.. 7.7 cm 1-way system Speakers.. 7.7 cm cone type Nominal impedance.. 6 Frequency range... 75 Hz to 20 kHz Dimensions.. 270 (W) x 90 (H) x 100 (D) mm 10 5/8 (W) x 3 9/16 (H) x 3 15/16 (D) in. Weight... 0.8 kg/ 1 lb. 12 oz
Note: Specifications and design subject to possible modification without notice due to improvements.
Published by Pioneer Corporation. Copyright 2005 Pioneer Corporation. All rights reserved.
We Want You Listening For A Lifetime
Used wisely, your new sound equipment will provide a lifetime of fun and enjoyment. Since hearing damage from loud noise is often undetectable until it is too late, this manufacturer and the Electronic Industries Associations Consumer Electronics Group recommend you avoid prolonged exposure to excessive noise. This list of sound levels is included for your protection. Example Quiet library, soft whispers Living room, refrigerator, bedroom away from traffic Light traffic, normal conversation, quiet office Air conditioner at 20 feet, sewing machine Vacuum cleaner, hair dryer, noisy restaurant Average city traffic, garbage disposals, alarm clock at two feet. THE FOLLOWING NOISES CAN BE DANGEROUS UNDER CONSTANT EXPOSURE 90 Subway, motorcycle, truck traffic, lawn mower 100 Garbage truck, chain saw, pneumatic drill 120 Rock band concert in front of speakers, thunderclap 140 Gunshot blast, jet plane 180 Rocket launching pad
Information courtesy of the Deafness Research Foundation.
Selecting fine audio equipment such as the unit youve just purchased is only the start of your musical enjoyment. Now its time to consider how you can maximize the fun and excitement your equipment offers. This manufacturer and the Electronic Industries Associations Consumer Electronics Group want you to get the most out of your equipment by playing it at a safe level. One that lets the sound come through loud and clear without annoying blaring or distortion-and, most importantly, without affecting your sensitive hearing. Sound can be deceiving. Over time your hearing comfort level adapts to higher volumes of sound. So what sounds normal can actually be loud and harmful to your hearing. Guard against this by setting your equipment at a safe level BEFORE your hearing adapts. To establish a safe level: Start your volume control at a low setting. Slowly increase the sound until you can hear it comfortably andclearly, and without distortion.

Les haut-parleurs avant sont dots dun dispositif de protection, destin protger les transducteurs dans des situations extrmes. Dans ces situations, le dispositif de protection agit et empche la production de son par les hautparleurs. Si cest le cas, rduisez le volume pour restituer une sortie normale aux haut-parleurs.

GUIDE DE DPANNAGE

SYMPTME 1. Absence de son CAUSE PROBABLE Fil de haut-parleur endommag ou connexion errone. Lampli-tuner est hors tension. La commande de volume est rgle sur zro. Ltat des signaux est excessif. CORRECTION Connectez correctement ou remplacez le fil. Mettez lampli-tuner sous tension. levez progressivement le volume sonore. Rduisez le niveau de sortie de lamplificateur (volume, commandes des basses, renforcement des graves) un niveau appropri. Rduisez le volume pour restituer une sortie normale aux haut-parleurs.

2. Le son est distordu.

3. Les haut-parleurs avant cessent soudain de produire leurs sons.
tat excessif des signaux pendant une dure prolonge.

FICHE TECHNIQUE

HAUT-PARLEURS AVANT / DAMBIANCE
Coffret.. Type ferm, bibliothque (blindage magntique) Systme... 1 voie, 7,7 cm Haut-parleur.. Type cne de 7,7 cm Impdance nominale... 6 Plage de frquences.. De 85 Hz 20 kHz Dimensions.. 105 x 115 x 114 mm (LxHxP) Poids HAUT-PARLEUR AVANT.. 0,6 kg HAUT-PARLEUR DAMBIANCE.. 0,66 kg
Coffret... Type bass rflex, sur plancher Systme... 1 voie, 16 cm Haut-parleur.. Type cne de 16 cm Impdance nominale... 6 Plage de frquences. De 30 Hz 2,5 kHz Dimensions.. 190 x 360 x 317 mm (LxHxP) Poids... 4,2 kg
Remarque : Spcifications et design sous rserve de changements sans pravis en raison damliorations ventuelles.
Coffret.. Type ferm, bibliothque (blindage magntique) Systme... 1 voie, 7,7 cm Haut-parleur.. Type cne de 7,7 cm Impdance nominale... 6 Plage de frquences.. De 75 Hz 20 kHz Dimensions. 270 x 90 x 100 mm (LxHxP) Poids... 0,8 kg
Publication de Pioneer Corporation. 2005 Pioneer Corporation. Tous droits de reproduction et de traduction reserves.

LIMITED WARRANTY

PIONEER ELECTRONICS (USA) INC. PIONEER ELECTRONICS OF CANADA, INC.
WARRANTY PERIOD For the period specified below from date of original retail purchase (the warranty period) from an authorized Pioneer dealer, Pioneer Electronics (USA) Inc. (PUSA), and Pioneer Electronics of Canada, Inc. (POC) warrants that products distributed by PUSA in the U.S.A., and by POC in Canada that fail to function properly under normal use due to a manufacturing defect when installed and operated according to the operating instructions enclosed with the unit will be repaired or replaced with a unit of comparable value, at the option of PUSA or POC, without charge to you for parts or actual repair work. Parts supplied under this warranty may be new or rebuilt at the option of PUSA or POC. WARRANTY PERIOD PRODUCT PARTS LABOR Loudspeakers / Subwoofers (amplifier section not included).. 1 YEAR 1 YEAR 1 YEAR Amplifier Section (if applicable).... 1 YEAR This warranty covers the product during the warranty period whether in the possession of the original owner or any subsequent owner. In the event service is required, the product must be delivered within the warranty period, transportation prepaid, fro m within the Country of purchase as explained in this document. You will be responsible for removal and installation of the product. WHAT'S NOT COVERED This warranty does not cover any product which is used in any trade or business, or in an industrial or commercial application. This warranty does not apply to any speaker that has been subjected to power in excess of its published power rating. This warranty does not cover the cabinet or any appearance item, any damage to the product resulting from alterations or modifications not authorized in writing by PUSA or POC, accident, misuse or abuse, or damage due to lightning or to power surges. This warranty does not cover the cost of parts or labor which would be otherwise provided without charge under this warranty obtained from any source other than a PUSA OR POC Authorized Service Company or other designated location. This warranty does not cover defects or damage caused by the use of unauthorized parts or labor, or from improper maintenance. ALTERED, DEFACED OR REMOVED SERIAL NUMBERS VOID THIS WARRANTY. YOUR RIGHTS PUSA and POC excludes any obligation on its part for incidental or consequential damages related to the failure of products to function properly under the conditions set forth above. IN THE U.S.A. - PUSA LIMITS ITS OBLIGATIONS UNDER ANY IMPLIED WARRANTIES INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, TO A PERIOD NOT TO EXCEED THE WARRANTY PERIOD. NO WARRANTIES SHALL APPLY AFTER THE WARRANTY PERIOD. SOME STATES DO NOT ALLOW LIMITATIONS ON HOW LONG AN IMPLIED WARRANTY LASTS, AND SOME STATES DO NOT ALLOW THE EXCLUSION OR LIMITATION OF INCIDENTAL OR CONSEQUENTIAL DAMAGES, SO THE ABOVE LIMITATIONS OR EXCLUSIONS MAY NOT APPLY TO YOU. THIS WARRANTY GIVES YOU SPECIFIC LEGAL RIGHTS, AND YOU MAY HAVE OTHER RIGHTS WHICH MAY VARY FROM STATE TO STATE. IN CANADA - EXCEPT AS EXPRESSLY PROVIDED HEREIN, THERE ARE NO REPRESENTATIONS, WARRANTIES, OBLIGATIONS OR CONDITIONS, IMPLIED, STATUTORY OR OTHERWISE, APPLICABLE TO THIS PRODUCT. TO OBTAIN SERVICE PUSA and POC have appointed a number of Authorized Service Companies throughout the U.S.A., and Canada should your product ever require service. To receive warranty service you will need to present your sales receipt or, if rented, your rental contract showing place and date of original owner's transaction. Should it become necessary to ship your unit, you will need to package the product carefully and send it, transportation prepaid by a traceable, pre-insured method, to an Authorized Service Company. Carefully package the product using adequate padding material to prevent damage in transit. The original container is ideal for this purpose. Include in the package your name, address, telephone number where you can be reached during business hours, a copy of your sales receipt and a detailed description of the problem. PUSA or POC, as appropriate, will pay for the cost of returning the repaired or replacement product to you within the Country of purchase. For additional information about this limited warranty or to locate the nearest PUSA or POC Authorized Service Company, please contact: IN THE U.S.A. CUSTOMER SERVICE DEPARTMENT PIONEER ELECTRONICS (USA) INC. P.O. BOX 1760 LONG BEACH, CA 90801 USA Phone: 1-800-421-1404 IN CANADA CUSTOMER SERVICE DEPARTMENT PIONEER ELECTRONICS OF CANADA, INC. 300 ALLSTATE PARKWAY MARKHAM, ON L3R OP2 Phone: 905-479-4411, 1-877-283-5901

DO NOT RETURN ANY PRODUCT TO THE ABOVE ADDRESSES. THEY ARE NOT SERVICE LOCATIONS.
RECORD THE PLACE AND DATE OF PURCHASE FOR FUTURE REFERENCE
Model No.: _____________________ Serial No.: _______________________ Purchase Date: ___________ Purchased From: ________________________
KEEP THIS INFORMATION AND YOUR SALES RECEIPT IN A SAFE PLACE

PIONEER CORPORATION

4-1, Meguro 1-Chome, Meguro-ku, Tokyo 153-8654. Japan
PIONEER ELECTRONICS (USA) INC. P.O. BOX 1540, Long Beach, California 90801-1540 PIONEER ELECTRONICS OF CANADA, INC. 300 Allstate Parkway Markham, Ontario L3R OP2, Canada PIONEER ELECTRONIC (EUROPE) N.V. Haven 1087 Keetberglaan 1,9120 Melsele, Belgium, TEL: 03/570.05.11 PIONEER ELECTRONICS AUSTRALIA PTY. LTD. 178-184 Boundary Road, Braeside, Victoria 3195, Australia, TEL: [03] 9586-6300 PIONEER ELECTRONICS DE MEXICO S.A. DE C.V. Blvd. Manuel Avila Camacho 138, 10 piso, Col. Lomas De Chapultepec, Mexico D.F. 11000, TEL: 52-55-9178-4270
Printed in China / Imprim en Chine <SRD1283-A>

04.12.28, 1:44 PM