Pioneer VSX-D514 Manual
Pioneer VSX-D514 Home Cinema Amplifier, size: 2.4 MB
Pioneer VSX-D514 Annexe 1
Here you can find all about Pioneer VSX-D514 like manual and other informations. For example: review, receiver.
Pioneer VSX-D514 manual (user guide) is ready to download for free.
On the bottom of page users can write a review. If you own a Pioneer VSX-D514 please write about it to help other people. [ Report abuse or wrong photo | Share your Pioneer VSX-D514 photo ]
User reviews and opinions
|lalanne cassou||2:14pm on Thursday, June 10th, 2010|
|multipul component in, optical in only one optical input and doesnt switch to component video|
|ded0rg||3:00pm on Thursday, May 20th, 2010|
|multipul component in, optical in only one optical input and doesnt switch to component video|
|gam4blin||4:05am on Tuesday, April 20th, 2010|
|$60.00 Pioneer Reciever!!!!! Very happy with the item, however, next time I suggest a little better padding inside the carton.|
Comments posted on www.ps2netdrivers.net are solely the views and opinions of the people posting them and do not necessarily reflect the views or opinions of us.
AUDIO/VIDEO MULTI-CHANNEL RECEIVER
VSX-D514 VSX-D714 VSX-D814
RISK OF ELECTRIC SHOCK DO NOT OPEN The lightning flash with arrowhead, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. CAUTION: TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. D8-10-1-2_En
Information to User Alteration or modifications carried out without appropriate authorization may invalidate the users right to operate the equipment. D8-10-2_En
CAUTION: This product satisfies FCC regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances such as radios and televisions, use shielded cables and connectors for connections. D8-10-3a_En
WARNING: The apparatus is not waterproofs, to prevent fire or shocks hazard, do not expose this apparatus to rain or moisture and do not put any water source near this apparatus, such as vase, flower pot, cosmetics container and medicine D3-4-2-1-3_En bottle etc.
Before changing the voltage, disconnect the AC power cord. Use a medium size screwdriver to change the voltage selector switch.
If the voltage is not properly set or if you move to an area where the voltage requirements differ, adjust the selector switches as follows. 1. Use a medium-size screwdriver. 2. First, insert the screwdriver in the groove of the voltage selector at the right, and adjust so that the tip of the groove points to the voltage value of your area. 3. Next, insert the screwdriver in the groove of the voltage selector at the left and adjust until the voltage is the same as at the right.
Italiano Franais Deutsch
Listening to Surround Sound
This receiver was designed with the easiest possible setup in mind, so with the following quick setup guide, you should have your system hooked up for surround sound in no time at all. In most cases, you can simply leave the receiver in the default settings. Be sure to complete all connections before connecting this unit to the AC power source. 1 Hook up your DVD player. For surround sound, youll want to hook up using a digital connection from the DVD player to the receiver. You can do this with either a coaxial, or an optical connection (you dont need to connect both). If you hook up using an optical cable, you should refer to Digital input settings on page 50 to assign the optical input to DVD. Use a video cord to connect the video output on your DVD player to the receiver using the jacks shown below. 2 Hook up your TV. Use a video cord to connect your receiver to the TV using the jacks as shown below.
CENTER SUB WOOFER
DIGITAL OUT OPT
IN CD FM UNBAL 75 AM LOOP ANTENNA MONITOR OUT OUT OPT OUT CONTROL IN VIDEO TV / SAT DVD /LD FRONT IN OUT IN MONITOR OUT SUB WOOFER PREOUT S-VIDEO TV/ SAT IN DVD /LD IN OUT DVR/ VCR IN
ASSIGNABLE ( D V D / LD) IN
SURROUND DVD 5.1CH INPUT
(TV / SAT) ASSIGNABLE DIGITAL IN
DVD PLA YER
(T V / SAT) IN
(TV / SAT) IN ASSIGNABLE DIGITAL IN COAX (CD) IN COAX (DVD OUT /LD) IN
DVD 5.1CH REC INPUT IN CD-R / TAPE / MD PLAY AUDIO
S P E A A K E IN R S
R SURROUND BACK L
R SURROUND L
SEE INSTRUCTION MANUAL
MONITOR OUT SUB WOOFER PREOUT
DVD / LD FRONT IN DVD 5.1CH REC INPUT IN CD-R / TAPE / MD
* The illustration shows the VSX-D814, but connections for the VSX-D514/D714 are the same.
3 Connect your speakers. A complete setup of speakers is shown here (six speakers for the VSX-D514/D714, and eight for the VSX-D814), but different home setups may vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best. Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative ( +/) terminals on the receiver match those on the speakers. You can use speakers with a nominal impedance between 616 (please see Switching the speaker impedance on page 72 if you plan to use speakers with an impedance of less than 8).
The multichannel input can only be used when DVD 5.1 ch is selected (see page 42).
Connecting video components
Connect your video components to the jacks as shown below. With digital video components (like a DVD player), you must use the connections shown on this page for the video signal, but in order to hear a digital source (like a DVD) you should hook up the audio to a digital input (see page 15). It is also a good idea to hook up your digital components with analog audio connections (see page 16). For better quality video, you can hook up using the component video jacks or the S-video jacks (quality descends in this order) on the rear of the receiver instead of the regular video jacks. Make sure they are connected to the video component using the same kind of connection. When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from the AC outlet. The arrows indicate the direction of the signal
(or Satellite tuner)
VIDEO L R
AUX FM UNBAL 75 AM LOOP ANTENNA MONITOR OUT OUT CONTROL IN VIDEO TV / SAT DVD /LD FRONT IN OUT IN MONITOR OUT SUB WOOFER PREOUT S-VIDEO TV/ SAT IN DVD /LD IN OUT DVR/ VCR IN
DVD or LD player
Connecting to the front panel video terminal
VSX-D714/D814 only Front video connections are accessed via the front panel using the VIDEO button. There are standard audio/video jacks as well as an S-video jack (the VSX-D814 also has an optical input). Hook them up the same way you made the rear panel connections.
Connect the AM loop antenna and the FM wire antenna as shown below. To improve reception and sound quality, connect external antennas (see Using external antennas below). Always make sure that the receiver is switched off and unplugged from the wall outlet before making or changing any connections.
Antenna snap connectors
Twist the exposed wire strands together and insert into the hole, then snap the connector shut.
AM loop antenna
Using external antennas
To improve FM reception
Connect an external FM antenna.
FM wire antenna
75 coaxial cable
FM UNBAL 75
Connect the FM wire antenna and fully extend vertically along a window frame or another suitable place that gives good reception.
To improve AM reception
Connect a 56 metre length of vinyl-coated wire to the AM antenna terminal without disconnecting the supplied AM loop antenna. For the best possible reception, suspend horizontally outdoors.
Assemble the antenna and connect to the receiver. Attach (if necessary) and face in the direction that gives the best reception.
Indoor antenna (vinyl-coated wire)
FM UNBAL 75
AM LOOP ANTENNA
Connecting the speakers (VSX-D514/D714)
A complete setup of six speakers (including the subwoofer) is shown below, but everyones home setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best. If youre not using a subwoofer, change the front speaker setting (see Speaker setting on page 46) to large. Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative ( +/) terminals on the receiver match those on the speakers. You can use speakers with a nominal impedance between 616 (please see Switching the speaker impedance on page 72 if you plan to use speakers with an impedance of less than 8). Be sure to complete all connections before connecting this unit to the AC power source.
Connecting the speakers (VSX-D814)
A complete setup of eight speakers (including the subwoofer) is shown below, but everyones home setup will vary. Simply connect the speakers you have in the manner shown below. The receiver will work with just two stereo speakers (the front speakers in the diagram) but using at least three speakers is recommended, and a complete setup is best for surround sound. If youre not using a subwoofer, change the front speaker setting (see Speaker setting on page 46) to large. Make sure you connect the speaker on the right to the right terminal and the speaker on the left to the left terminal. Also make sure the positive and negative ( +/) terminals on the receiver match those on the speakers. You can use speakers with a nominal impedance between 616 (please see Switching the speaker impedance on page 72 if you plan to use speakers with an impedance of less than 8). Be sure to complete all connections before connecting this unit to the AC power source.
FL DIMMER Dims or brightens the display. 4 MASTER VOLUME +/ Use to set the listening volume.
5 Receiver and component control buttons (Press the corresponding MULTI CONTROL button first to access). These controls function according to the component youve selected. TOP MENU Displays the disc top menu of a DVD. SR+ VSX-D714/D814 only Switches the SR+ mode on/off (page 54). DTV MENU Displays menus on a digital TV. AUDIO Changes the audio language or channel with DVD discs. MCACC SETUP VSX-D714/D814 only Use to setup your speaker system using the multichannel acoustic calibration system (page 52). MENU Displays the disc menu of DVD-Video discs. It also displays TV menus. INPUT ATT Attenuates (lowers) the level of an analog input signal to prevent distortion. T.EDIT Use to memorize and name a station for recall using the STATION +/ buttons (page 57). GUIDE Displays the guides on a digital TV.
SUBTITLE Displays/changes the subtitles included in multilingual DVD-Video discs. SLEEP Use to put the receiver in sleep mode and select the amount of time before the receiver turns off. 6 (TUNE +/, ST +/) /ENTER Use the arrow buttons when setting up your surround sound system (see page 44). Also used to control DVD menus/options and for deck 1 of a double cassette deck player. Use the TUNE +/ buttons to find radio frequencies and use ST +/ to find preset stations (page 58).
CLASS Switches between the three banks (classes) of radio station presets (page 57). MPX Switches between stereo and mono reception of FM broadcasts. If the signal is weak then switching to mono will improve the sound quality (page 56). D.ACCESS After pressing, you can access a radio station directly using the number buttons (page 56). 8 Number buttons Use the number buttons to directly select a radio frequency (page 56) or the tracks on a CD, DVD, etc. 9 CHANNEL +/ Use to select channels when using a VCR, DVR, etc. 10 INPUT SELECT Use to select the input source. 11 LED This lights when a command is sent from the remote control. 12 SOURCE Press to turn on/off other components connected to the receiver. 13 DISC (ENTER) The buttons use depends on the component selected. It can be used to enter commands for TV or DTV, and can also be used to select a disc in a multi-CD player. 14 TV CONTROL buttons These buttons are dedicated to control the TV assigned to the TV CONT button. Thus if you only have one TV to hook up to this system assign it to the TV CONT MULTI CONTROL button. If you have two TVs, assign the main TV to the TV CONT button.
7 Component/Tuner control buttons The main buttons ( , , etc.) are used to control a component after you have selected it using the MULTI CONTROL buttons. The tuner/DTV controls above these buttons can be accessed after you have selected the corresponding MULTI CONTROL button (TUNER or TV/SAT (when connected to DTV)). RETURN Returns to the last screen selected when using a digital TV tuner. BAND DTV ON/OFF Switches between the tuner AM and FM bands (page 56). Also switches a digital TV on/off. DTV INFO Use to bring up information screens on a digital TV. DISPLAY Use to switch the display between the station preset name and the frequency for the tuner.
AUTO ON AUTO
ON AUTO ON AUTO
Using the Virtual Surround Back mode (VSB)
Selecting this mode allows you to hear a virtual back channel through your surround speakers. For example, you can choose to listen to sources with no surround back channel information (for example, 5.1 encoded material) with emulated 6.1 encoding (VSB ON). Sometimes the material may sound better in the 5.1 format for which it was originally encoded. In this case you can simply switch it off (VSB OFF) or (VSX-D714/ D814 only) have the receiver only apply this effect to 6.1 encoded sources like Dolby Digital EX or DTS-ES (VSB AUTO). The table indicates when you will hear the virtual surround back channel. Press SB CH MODE / VSB MODE (front panel) to select a virtual surround back channel option.
Each press cycles through the options as follows: VSB AUTO (VSX-D714/D814 only) VSB ON VSB OFF
You cant use the Virtual Surround Back mode with headphones, the STEREO / DIRECT mode, or if the Speaker setting on page 46 is set to S. VSX-D714/D814 only You can only use the Virtual Surround Back mode if the surround speakers are on and the Surround back speaker setting on page 46 is set to SB or (VSX-D814 only) SB SW. You cant adjust the surround back channel level when youre listening to the virtual surround back channel.
Virtual Surround Back mode ON AUTO ON AUTO
Using Midnight and Loudness listening
The Midnight listening feature allows you to hear effective surround sound of movies at low volume levels. The effect automatically adjusts according to the volume at which youre listening. The Loudness listening feature can be used to get good bass and treble from music sources at low volume levels.
Using the tone controls
Depending on what you are listening to, you may want to adjust the bass or treble using the front panel tone control.
* Illustration shows the VSX-D814 model 1 Press TONE to select the frequency you want to adjust. Press to switch between BASS and TREBLE. 2 Use the MULTI JOG dial to change the amount of bass or treble as necessary. Wait about five seconds for your changes to be input automatically.
Press MIDNIGHT/LOUDNESS to switch between MIDNIGHT, LOUDNESS, and OFF.
You cant use MIDNIGHT/LOUDNESS when DVD 5.1 ch has been selected, or when listening to a DTS 96kHz/24 bit source and 96 kHz PCM.
You can only use the tone controls when STEREO/DIRECT is selected. DIRECT will switch to STEREO when the tone controls are used. VSX-D714/D814 only The tone controls affect SPEAKER A only. They cant be used when SPEAKER A is switched off.
Playing other sources
Press DVD 5.1 on the front panel to select the multichannel inputs.
Speaker setting (page 46) Specify the number and type of speakers you have connected. Subwoofer setting (page 47) Specify how the subwoofer is used. Crossover frequency setting (page 47) Determine which frequencies will be sent to the subwoofer (or large speakers). LFE attenuator setting (page 47) Choose the attenuator level for the LFE channel. Front speaker distance setting (page 48) Specify the distance from your listening position to your front left speaker. Center speaker distance setting (page 48)
Specify the distance from your listening position to your center speaker.
Surround speaker distance setting
(page 48) Specifies the distance from your listening position to your surround back speakers.
Subwoofer distance setting (page 49) Specify the distance from your listening position to your subwoofer. Dynamic range control setting (page 50) Compress the dynamic range of the sound track. Dual mono setting (page 50) Isolate one channel when listening to discs with dual mono encoding. Digital input settings (page 50) Specify the components to be assigned to the digital inputs (below).
1 Press RECEIVER on. 2 Press RECEIVER.
to turn the power
3 Use or to choose the option you want to adjust. It will be easiest to adjust each of the settings in turn, following the order below (and on the following pages). The current setting is shown for each option as you cycle through the display. The VSX-D514 and VSXD714/D814 settings are separated below for easy reference.
Coaxial digital input 1 setting Coaxial digital input 2 setting Optical digital input 1 setting
Surround left speaker distance setting
(page 49) Specify the distance from your listening position to your surround left speaker.
Subwoofer distance setting (page 49)
Speaker setting (page 46)
Specify the number and type of speakers you have connected.
Surround back speaker setting (page 46)
Specify the distance from your listening position to your subwoofer.
Dynamic range control setting (page 50)
If you find that you cant tune into stations successfully, the frequency step may not be suitable for your country/region. Heres how to switch the setting: 1 Switch the receiver into standby.
2 On the front panel, press STANDBY/ ON while you press and hold the BAND (VSX-D714/D814) / CLASS (VSX-D514) button. The channel tuning step alternates between FM 100 kHz/AM 10kHz and FM 50 kHz/AM 9 kHz each time you do this.
To erase a station name, simply repeat steps 1-3 and input four spaces instead of a name. Once you have named a station preset, you can press DISPLAY when listening to a station to switch the display between the name and the frequency.
Making an audio or a video recording
You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV). Keep in mind you cant make a digital recording from an analog source or viceversa, so make sure the components you are recording to/from are hooked up in the same way (see Connecting up on page 14 for more on connections). If you want to record a video source, you also need to use the same type of connection for the source as for the recorder. For example, you cant record a component hooked up to Svideo jacks with a recorder hooked up to the component video outputs (see page 18 for more on video connections). 1 Select the source you want to record. Use the MULTI CONTROL buttons (or INPUT SELECT). 2 Select the input signal (if necessary). Press SIGNAL SELECT (front panel) to select the input signal corresponding to the source component (see page 38 for more on this). 3 Prepare the source you want to record. Tune to the radio station, load the CD, video, DVD etc. 4 Prepare the recorder. Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automaticallycheck the components instruction manual if youre unsure. 5 Start recording, then start playback of the source component.
DVD/LD TV/SAT DVR/VCR VIDEO
CD CD-R/ TAPE/MD TUNER AUX
DVD/LD CD TV / SAT DVR/VCR TV CONT
The receiver's volume, balance, tone (bass, treble, loudness), and surround effects have no effect on the recorded signal.
PUT ATT FL DIMMER
* Illustrations show the VSX-D814 model
Controlling the rest of your system
Setting the remote to control other components
There are several ways to set your remote to control the other components in your system. The easiest way to do this is to assign the components manufacturer preset code (starting on page 66) to one of the MULTI CONTROL buttons on the remote control. The buttons can be set to control the following components:
Selecting preset codes directly
DVD/LD: TV/SAT: DVR/VCR: CD: CD-R/TAPE: TV CONT: TUNER:
DVD or LD player TV or Satellite tuner Digital Video Recorder or VCR CD player CD Recorder, Tape deck or MD player TV or Cable TV tuner FM/AM tuner
VSX-D814 only If you cant find a preset code that matches the component you want to control, you can still teach the remote individual commands from another remote control (page 61).
1 While pressing the RECEIVER button, press and hold the 1 button. The LED blinks. 2 Press the MULTI CONTROL button for the component you want to control. The LED lights.
The remote control will exit an operation after 1 minute of inactivity.
3 Use the number buttons to enter the preset code. You can find the preset codes on page 66 (VSX-D514/D714) and page 68 (VSX-D814). The LED blinks again after you enter the code. If the correct code has been input the power of the component being input will turn on or off. The power of the component being input will only turn on or off if that component is able to be turned on directly by remote control. You can only input a code for the component type written on each MULTI CONTROL button (except RECEIVER and TUNER). Even if you dont input a preset code for the TV (TV/SAT MULTI CONTROL button) you will be able to control your TV using the dedicated TV CONTROL on the remote if you have assigned it to the TV CONT button. You may not be able to use a particular code even if it is listed on page 66. The remote control buttons will not be able operate other equipment unless preset with the method above. 4 Repeat steps 2 through 3 to try a different code, or to enter a code for another component you want to control. 5 When youre done, press RECEIVER.
ENTER / ENTER GUIDE CHANNEL +/ AUDIO
Starts playback. Fast rewinds/fast forwards the tape. & Navigates DVD menu/options. Displays/changes the subtitles on multilingual DVDs. Selects channels. Changes the audio language or channel.
DVD/DVR player VCR/DVR player DVD/DVR player
Preset Code List (VSX-D514/D714)
You should have no problem controlling a component if you find the manufacturer in this list, but please note that there are cases where codes for the manufacturer in the list will not work for the model that you are using. There are also cases where only certain functions may be controllable after assigning the proper preset code.
The TV, STB and DTV codes can only be set to the TV/SAT or TV CONT button.
TOSHIBA 001 SONY 002 PANASONIC 003 JVC 004 SAMSUNG 005 SHARP 006 AKAI 007 RCA 009, 011 DENON 010 HITACHI 012 PHILIPS 013 ZENITH 014 THOMSON 015 SONY 016 (video game) MICROSOFT 017(Videogame) PIONEER 000, 008
PHILIPS 607 SONY 604 PANASONIC 608, 622 TOSHIBA 605, 626 SHARP 602, 619, 627 HITACHI 606, 624, 625 SANYO 621, 614 MITSUBISHI 609 GOLDSTAR 610, 623 JVC 613 FUNAI 658 AIWA 660 NEC 659 GRANDIENTE 630 PIONEER 600
DENON 810 FISHER 813 JVC 802 PANASONIC 803 KENWOOD 804, 807 ONKYO 808, 809 SONY 801, 806 TEAC 805 YAMAHA 811, 812 PIONEER 800
PIONEER 229, 207, 231, 232 PANASONIC 226, 230 VICTOR 227 TOSHIBA 228
RCA 401, 413, 415 ZENITH 403 MAGNAVOX 414 FISHER 426, 412, 427 PANASONIC 408 , 432 , 433 TOSHIBA 405 JVC 428, 430, 429, 431, 407 HITACHI 406, 436, 434 SONY 416, 417, 404, 457, 458 , 459 MITSUBISHI 409, 420, 421, 422, 423, 424 SANYO 410, 425, 435 SHARP 402, 418, 419 GOLDSTAR 411 GRADIENTE 441 PIONEER 400
DENON 309 JVC 303 PANASONIC 304, 326 KENWOOD 310, 311, 321 MARANTZ 323 ONKYO 320, 308, 307 PHILIPS 312, 322 RCA 302, 319 SANYO 313 SONY 301, 316, 317, 318 TEAC 305, 306, 327, 324, 325 YAMAHA 315 , 314 , 328 PIONEER 300
STB (SATELLITE/ CATV)
TV / SAT TV CONT
JERROLD 701, 702, 703, 704, 711, 712, 713 , 714, 715, 716 S.ATLANTA 705, 706, 708, 709 ZENITH 707, 717, 710 PIONEER 700, 718
SONY 101 PANASONIC 105, 106 PHILIPS 104 KENWOOD 103 RCA 107 PIONEER 100
On digital STB
RCA 601, 615, 616, 617, 618 ZENITH 603, 620 MAGNAVOX 612, 629 GE 611, 628
RCA 201, 203, 209 SONY 202 ECHOSTAR 205 PRIMESTAR 206 BELL 208 PIONEER 200
PHILIPS 346 PIONEER 345
SONY 901 KENWOOD 903 SHARP 902 TEAC 904 ONKYO 905 DENON 906 PIONEER 900, 907
Preset Code List (VSX-D814)
The TV CONT button will only accept preset codes for TV, STB and DTV.
TOSHIBA 1010 SONY 1009 SAMSUNG 1008 JVC 1005 RCA 1007 DENON 1004 PHILIPS 1006 TOSHIBA 1010 YAMAHA 1011, 1012 PIONEER 1001, 1002, 1003
SONY 2008 PHILIPS 2006, 2007 PANASONIC 2005 KENWOOD 2004 DENON 2003 YAMAHA 2009 PIONEER 2001, 2002
PIONEER 5001,5002, 5003, 5004, 5005, 5006, 5007, 5008, 5009, 5010 ADMIRAL 5011, 5012. 5013 AIWA 5014, 5015 AKAI 5016 ALBA 5017 AOC 5018 BESTAR 5019 BLAUPUNKT 5020 BLUE SKY 5021 BRANDT 5022 BROCSONIC 5023 BUSH 5024
CLATRONIC 5025 CRAIG 5026, 5027, 5028, 5029 CROSLEX 5030 CURTIS MATHIS 5031,5032, 5033 DAEWOO 5034, 5035, 5036, 5037, 5038, 5039 DAYTRON 5040 DUAL 5041 EMERSON 5042, 5043,5044,5045, 5046, 5047, 5048 FERGUSON 5049, 5050 FIRST 5051 FISHER 5052 FUJITSU 5053 FUNAI 5054, 5055, 5056 GE 5057, 5058, 5059, 5060 GOLDSTAR 5061, 5062, 5063, 5064 GOODMANS 5065, 5066 HITACHI 5067, 5068, 5069, 5070, 5071 ICE 5072 IRRADIO 5073 ITT/NOKIA 5074,5075 JC PENNY 5076, 5077, 5078, 5079 JVC 5080, 5081 KENDO 5082 KTV 5083, 5084 LOEWE 5085 LXI 5086, 5087, 5088, 5089, 5090 MAGNAVOX 5091 MARK 5092 MATSUI 5093, 5094 MATSUSHITA 5095, 5096 MEDION 5097 MITSUBISHI 5098, 5099
MIVAR 5100 NEC 5101, 5102 NOKIA OCEANIC 5103 NORDMENDE 5104,5105 OKANO 5106 ONWA 5107 PANASONIC 5108, 5109, 5110, 5111 PHILCO 5112, 5113, 5114 PHONOLA 5115 PORTLAND 5116, 5117 PROSCAN 5118 QUASAR 5119, 5120 RADIO 5121, 5122 RADIOSHACK 5123,5124, 5125 RADIOLA 5126 RCA/PROSCAN 5127, 5128, 5129 SABA 5130 SAMSUNG 5131, 5132 SANYO 5133, 5134, 5135 SCHNEIDER 5136 SCOTT 5137, 5138 SHARP 5139, 5140 SIEMENS 5141 SIGNATURE 5142, 5143 SONY 5144, 5145 SYLVANIA 5146, 5147 SYMPHONIC 5148 TATUNG 5149 TELEFUNKEN 5150, 5151 THORN 5152 TOSHIBA 5153, 5154 UNIVERSUM 5155 VIDECH 5156, 5157 W. WHOUSE 5158 WARDS 5159, 5160, 5161 WATSON 5162 ZENITH 5163, 5164
PIONEER 3001, 3002, 3003, 3004, 3005 ADMIRAL 3006 AIWA 3007, 3008, 3009 AKAI 3010, 3011 ALBA 3012 AUDIO DYNAMIC 3013, 3014 BELL&HOWELL 3015 BLAUPUNKT 3016, 3017 BROCSONIC 3018, 3019 BUSH 3020 CANON 3021 CGM 3022, 3023 CITIZEN 3024 CLATRONIC 3025 CRAIG 3026 CURTIS MATHIS 3027, 3028, 3029 DAEWOO3030, 3031, 3032 DBX 3033, 3034 DIMENSIA 3035 EMERSON 3036, 3037,3038, 3039, 3040, 3041 FERGUSON 3042 FISHER 3043, 3044, 3045, 3046 FUNAI 3047, 3048 GE 3049, 3050, 3051 GOLDSTAR 3052 GOODMANS 3053, 3054 GRUNDIG 3055 HITACHI 3056, 3057, 3058, 3059, 3060 INSTANT REPLAY 3061, 3062 ITT/NOKIA 3063
PIONEER 6001, 6002, 6003, 6004, 6005, 6006 BELL 6049 BLAUPUNKT 6007 ECHOSTAR 6047 GENERAL INSTRUMENT 6008 GOLDSTAR 6009 GRUNDIG 6010, 6011 HAMLIN 6012, 6013
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
Problem The power does not turn on.
Remedy Connect the power plug to the wall outlet. Disconnect the power plug from the outlet, and insert again. Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically. If the power shuts off automatically, take the unit to your nearest
Pioneer authorized service center or your dealer for servicing.
The unit may have been switched on using the wrong voltage setting. Make sure you switch the VOLTAGE SELECTOR on the rear panel to the right voltage for your country or region, then reset the unit (page 72) before switching on again. No sound is output when a function is selected. Make sure the component is connected correctly (refer to Connecting up on page 14). Press MUTE on the remote control to turn muting off. Adjust the MASTER VOLUME. Make sure the component is connected correctly (refer to Connecting up on page 14). Select the correct component (use the MULTI CONTROL buttons).
No image is output when a function is selected.
Problem Considerable noise in radio broadcasts.
Remedy Tune in the correct frequency. Connect the antenna (refer to page 19). Route any loose cables away from the antenna terminals and wires. Fully extend the FM wire antenna, position for best reception, and secure to a wall. Connect an outdoor FM antenna (refer to page 19). Adjust the direction and position for best reception. Connect an additional internal or external AM antenna (refer to page 19). Turn off the equipment causing the noise or move it away from the receiver. Move antennas farther away from equipment causing the noise.
Resetting the main unit
Use this procedure to reset all the receivers settings to the factory default. Use the front panel controls to do this. 1 Switch the receiver on.
Switching the speaker impedance
We recommend using speakers of 8 with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 impedance rating. With the receiver in standby, press STANDBY/ON while holding down the SPEAKERS / SPEAKER IMPEDANCE button. Each time you do this, you switch between the impedance settings: SP 6 OHM Use this setting if your speakers are rated at 6. SP 8 OHM Use this setting if your speakers are rated at 8 or more.
2 While holding down the TONE button, press and hold the STANDBY/ON button for about three seconds. 3 When you see RESET? appear in the display, press the TONE button. OK? shows in the display. 4 Press TONE once more to confirm. OK appears in the display to indicate that the receiver has been reset to the factory default settings.
Continuous power output (stereo)
Front.100 W (DIN 1kHz, THD 1.0%, 8 )
Signal-to-Noise Ratio (IHF, short circuited, A network)
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT. 96 dB
Signal-to Noise Ratio [EIA, at 1 W (1 kHz)]
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT. 79 dB
Continuous power output (surround)
Front. 100 W per channel (1kHz, 1.0%, 8 ) Center. 100 W (1kHz, 1.0%, 8 ) Surround. 100 W per channel (1kHz, 1.0%, 8 ) Surround Back. 100 W (1kHz, 1.0 %, 8 ) (VSX-D814 only)
DVR/VCR, DVD/LD, TV/SAT. 1 Vp-p/75
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT. 200 mV/47 k
DVR/VCR, MONITOR OUT. 1 Vp-p/75
DVR/VCR, DVD/LD, TV/SAT MONITOR. 5 Hz to 7 MHz dB Signal-to-Noise Ratio. 55 dB
CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT. 5 Hz to 100,000 Hz dB
Component video section
DVR/VCR REC, CD-R/TAPE/ MD REC. 200 mV/2.2 k
DVD/LD, TV/SAT. 1 Vp-p/75
Bass. 6 dB (100 Hz) Treble. 6 dB (10 kHz) Loudness. +6.5 dB/+3 dB (100 Hz/10 kHz) (at volume level 50 dB)
MONITOR OUT. 1 Vp-p/75
DVD/LD, TV/SAT MONITOR. 5 Hz to 40 MHz dB Signal-to-Noise Ratio. 55 dB
READ INSTRUCTIONS All the safety and operating instructions should be read before the product is operated. RETAIN INSTRUCTIONS The safety and operating instructions should be retained for future reference. HEED WARNINGS All warnings on the product and in the operating instructions should be adhered to. FOLLOW INSTRUCTIONS All operating and use instructions should be followed. CLEANING The product should be cleaned only with a polishing cloth or a soft dry cloth. Never clean with furniture wax, benzine, insecticides or other volatile liquids since they may corrode the cabinet. ATTACHMENTS Do not use attachments not recommended by the product manufacturer as they may cause hazards. WATER AND MOISTURE Do not use this product near water for example, near a bathtub, wash bowl, kitchen sink, or laundry tub; in a wet basement; or near a swimming pool; and the like. ACCESSORIES Do not place this product on an unstable cart, stand, tripod, bracket, or table. The product may fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturers instructions, and should use a mounting accessory recommended by the manufacturer. CART A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.
VENTILATION Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturers instructions have been adhered to. POWER SOURCES This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. LOCATION The appliance should be installed in a stable location. NONUSE PERIODS The power cord of the appliance should be unplugged from the outlet when left un-used for a long period of time.
GROUNDING OR POLARIZATION If this product is equipped with a polarized alternating current line plug (a plug having one blade wider than the other), it will fit into the outlet only one way. This is a safety feature. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the polarized plug. If this product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin, it will only fit into a grounding type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding type plug. POWER-CORD PROTECTION Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product. OUTDOOR ANTENNA GROUNDING If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code, ANSI/NFPA 70, provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode. See Figure A. LIGHTNING For added protection for this product during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges. POWER LINES An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal. OVERLOADING Do not overload wall outlets, extension cords, or integral convenience receptacles as this can result in a risk of fire or electric shock.
OBJECT AND LIQUID ENTRY Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product. SERVICING Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel. DAMAGE REQUIRING SERVICE Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions: When the power-supply cord or plug is damaged. If liquid has been spilled, or objects have fallen into the product. If the product has been exposed to rain or water. If the product does not operate normally by following the operating instructions. Adjust only those controls that are covered by the operating instructions as an improper adjustment of other controls may result in damage and will often require extensive work by a qualified technician to restore the product to its normal operation. If the product has been dropped or damaged in any way. When the product exhibits a distinct change in performance this indicates a need for service. REPLACEMENT PARTS When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards. SAFETY CHECK Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition. WALL OR CEILING MOUNTING The product should not be mounted to a wall or ceiling. HEAT The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.
Batteries with the same shape may have different voltages. Do not use different batteries together. When disposing of used batteries, please comply with governmental regulations or environmental public instructions rules that apply in your country or area.
Making cable connections
Make sure not to bend the cables over the top of this unit (as shown in the illustration). If this happens, the magnetic field produced by the transformers in this unit may cause a humming noise from the speakers.
Installing the receiver
Please note the following points: Do not place objects directly on top of this unit. This would prevent proper heat dispersal. When installing on a rack, shelf, etc., be sure to leave more than 8 inches (20 cm.) of space above the receiver.
Loading the batteries
Operating range of remote control unit
The remote control may not work properly if: There are obstacles between the remote control and the receiver's remote sensor. Direct sunlight or fluorescent light is shining onto the remote sensor.
Dry cell batteries (AA size IEC R6) 2
The receiver is located near a device that is emitting infrared rays. The receiver is operated simultaneously with another infrared remote control unit.
Incorrect use of batteries may result in such hazards as leakage and bursting. Observe the following precautions: Never use new and old batteries together. Insert the plus and minus sides of the batteries properly according to the marks in the battery case.
03.12.12, 3:36 PM
5 minute guide
Introduction to home theater
You are probably used to using stereo equipment to listen to music, but may not be used to home theater systems that give you many more options (such as surround sound) when listening to soundtracks. Home theater refers to the use of multiple audio tracks to create a surround sound effect, making you feel like you're in the middle of the action or concert. The surround sound you get from a home theater system depends not only on the speakers you have set up in your room, but also on the source and the sound settings of the receiver. DVD-Video has become the basic source material for home theater due to its size, quality, and ease of use. Depending on the DVD, you can have up to seven different audio tracks coming from one disc, all of them being sent to different speakers in your system. This is what creates a surround sound effect and gives you the feeling of being there. This receiver will automatically decode Dolby Digital, DTS, or Dolby Surround DVD-Video discs, according to your speaker setup. In most cases, you wont have to make changes for realistic surround sound, but other possibilities (like listening to a CD with multi-channel surround sound) are explained in Listening to your system, starting on page 26.
Front Center Surround Sub Speakers Speaker Speakers Woofer 2.0 ch 2.1 ch 3.0 ch 3.1 ch 4.0 ch 4.1 ch 5.0 ch 5.1 ch
4 Press ENTER. The display prompts you to select your room size. 5 Use the MULTI JOG dial to choose your room size. Depending on the distance of your speakers from the listening position, choose between small, medium, or large (S, M or L), M being an average-sized room. 6 Press ENTER.
7 Use the MULTI JOG dial to choose your listening position. You can cycle between the following choices:
FWD MID BACK
FWD If you are nearer to the front speakers than the surround speakers MID If you are equal distance from the front and surround speakers
Before making or changing the connections, switch off the power and disconnect the power cord from the AC outlet.
Use audio/video cords (not supplied) to connect the audio/video components and a video cord to connect the monitor TV. Connect red plugs to R (right), white plugs to L (left), and the yellow plugs to VIDEO. Be sure to insert completely.
Component video cords (VSX-D514 only)
Use component video cords to get the best possible color reproduction of your video source. The color signal of the TV is divided into the luminance (Y) signal and the color (PB and PR) signals and then output. In this way, interference between the signals is avoided. Connect from the component video jacks on the rear of the receiver to the component video jacks on the video component you are hooking up.
S-video cables (VSX-D514 only)
Use S-video cables (not supplied) to get clearer picture reproduction than regular video cords. Connect from an S-video jack on the rear of the receiver to an S-video jack on the video component you are hooking up. Be sure to insert completely.
SV IDE O
Digital audio cords/Optical cables
Commercially available digital audio coaxial cords (standard video cords can also be used) or optical cables (not supplied) are used to connect digital components to this receiver. Be sure to insert completely.
Digital audio coaxial cord (or standard video cord) Optical cable
03.12.4, 7:46 PM
Connecting digital components
For proper decoding of Dolby Digital/DTS soundtracks, you need to make digital audio connections. You can do this by either coaxial or optical connections (you dont need to do both). The quality of these two types of connections is the same, but since some digital components only have one type of digital terminal, it is a matter of matching like with like (for example, the coaxial output from the component to the coaxial input on the receiver). This receiver has two coaxial and one optical inputs. Connect your digital components as shown below. When connecting your equipment, always make sure the power is turned off and the power cord is disconnected from the wall outlet.
Extra Power mode speaker set up
VSX-D414 only see Using the Advanced surround effects on page 27 to switch on the Extra Power mode (EX POWER). DO NOT CONNECT A MONITOR, TV SET, HEATER, OR SIMILAR APPLIANCE TO THIS UNIT'S AC OUTLET. Do not connect appliances with high power consumption to the AC OUTLET in order to avoid overheating and fire risk. This can also cause the receiver to malfunction.
Subwoofer Surround left Surround right
This unit should be disconnected by removing the power plug from the wall socket when not in regular use (ex. when on vacation).
[switched 100 W (0.8 A) max]
Power supplied through this outlet is turned on and off by the receiver's power switch. Total electrical power consumption of connected equipment should not exceed 100 W (0.8 A).
Handle the power cord by the plug. Do not pull out the plug by tugging the cord and never touch the power cord when your hands are wet as this could cause a short circuit or an electric shock. Do not place the unit, a piece of furniture, etc., on the power cord, or pinch the cord. Never make a knot in the cord or tie it with other cords. The power cords should be routed such that they are not likely to be stepped on. A damaged power cord can cause a fire or give you an electrical shock. Check the power cord once in a while. When you find it damaged, ask your nearest Pioneer authorized service center or your dealer for a replacement.
AC OUTLET SWITCHED 100 W MAX 0.8 A MAX
Controls and displays
STEREO (pages 28) Switches direct playback on or off. Direct playback bypasses the tone controls and channel levels for the most accurate reproduction of a source.
RECEIVER SLEEP FL DIMMER INPUT ATT
INPUT SELECTOR DVD/LD DVD 5.1CH TV/SAT DVR/VCR
CD-R/ TAPE/MD CD FM AM
MIDNIGHT/LOUDNESS (page 29) Use to switch to Midnight or Loudness listening. TOP MENU (DVD control) Displays the disc top menu of a DVD. TUNER EDIT (receiver control) (pages 3940) Press to memorize and name a station for recall. 4 DVD Use to switch over to the DVD controls on the remote control.
ADVANCED MIDNIGHT/ STANDARD SURROUND STEREO LOUDNESS
10 } ] and ENTER/SETUP buttons Use these arrow buttons when setting up your surround sound system. These buttons are also used to control DVD menus/options. 11 RECEIVER Use to switch to the receiver controls on the remote control. Also used when setting up the surround sound for the receiver. 12 Tuner controls (page 3840) The TUNING +/ buttons can be used to find radio frequencies. The STATION +/ buttons can be used to select preset radio stations. CLASS (page 40) Use to switch between the three banks (classes) of station presets.
1 STANDBY/ON Switches the receiver between on and standby. 2 INPUT SELECT buttons Use to select the input source. 3 STATION (+/) buttons (page 40) Selects station presets when using the tuner. 4 TUNING (+/) buttons (page 38) Selects the frequency when using the tuner. 5 Remote sensor Receives the signals from the remote control. 6 ENTER
9 TUNER EDIT (pages 3940) Press to memorize and name a station for recall. 10 CLASS (pages 3940) Switches between the three banks (classes) of station presets. 11 MPX (page 38) Press the MPX button to receive a radio broadcast in mono. 12 INPUT ATT Use to attenuate (lower) the level of an analog input signal to prevent distortion. 13 FL DIMMER Use this button to make the fluorescent display (FL) dimmer or brighter. 14 MUTE Use to mute the sound or restore the sound if it has been muted. LISTENING MODE buttons STANDARD (pages 26, 36) Press for Standard decoding and to switch between the various Pro Logic II options.
7 MULTI JOG dial The MULTI JOG dial performs a number of tasks. Use it to select options after pressing TONE, QUICK SETUP or TUNER EDIT. 8 PHONES jack Use to connect headphones.
When the headphones are connected, there is no sound output from the speakers.
ADVANCED SURROUND (pages 27, 36) Use to switch between the various surround modes. STEREO/DIRECT (page 28) Switches direct playback on or off. Direct playback bypasses the tone controls and channel levels for the most accurate reproduction of a source. 16 SIGNAL SELECT (page 29) Use to select between an analog or digital signal. 17 MIDNIGHT/LOUDNESS (page 29) Use to switch to Midnight or Loudness listening. 18 SPEAKER IMPEDANCE (page 37) Use to switch the speaker impedance when using low-impedance speakers. 19 VSB MODE (page 28) Press to switch the Virtual Surround Back mode on or off. 20 TONE (page 29) Press this button to access the bass and treble controls, which you can then adjust with the MULTI JOG dial. QUICK SETUP (page 10) MASTER VOLUME
FS-CS-SS FL-C -S FL-C -SS FL-C -SL FL-CS-S FL-CS-SS FL-CS-SL FS-CS-S FS-C -SS FS-C -S FL-CL-SL FL-CL-SS FL-CL-S
The setting display is automatically exited after 3 minutes of inactivity.
Default setting: S (all speakers) You must let the receiver know how many speakers you have, and how big they are. The size you choose (large or small) determines how much bass is sent from the receiver to the speakers. In the display, F, C, and S refer to front, center, and surround speakers respectively. Speaker size is denoted as L for large speakers, S for small speakers, and (asterisk) if no speaker is connected. Cycle through the available choices using or and choose a configuration that matches your speaker setup. One of the following configurations should match your setup:
Default setting: YES You can choose whether the subwoofer is used or not. Use the plus (PLUS) setting for extra bass. Use or to select a subwoofer setting: YES Sends bass frequencies from the small (S) speakers to the subwoofer. PLUS Sends bass frequencies from all speakers to the subwoofer (L speakers will also output bass). NO No bass frequencies are sent to the subwoofer.
LFE attenuator setting
If you chose the small front speaker setting, SW YES is automatically set and locked. You can only select the PLUS setting if the front speakers are set to L. Default setting: 0 dB Dolby Digital and DTS audio sources include ultra-low bass tones. Set the LFE attenuator as necessary to prevent the ultra-low bass tones from distorting the sound from the speakers. Use or to set the attenuation level (0 dB, 10 dB or dB()).
Crossover frequency setting
Default setting: 100 Hz Crossover frequency is the point where the receiver divides the high and low sounds (the frequencies) between the speakers. Since most smaller speakers cant handle deep bass tones, you can send these sounds to the subwoofer (or if you dont have a subwoofer, the large (L) speakers in your system) instead of the speakers set to small (S) in your setup. Choose the point at which you want the frequency routed to the subwoofer (or L speakers). We recommend setting this to 200 Hz if your S speakers are smaller bookshelf-type speakers. Use or to specify the crossover frequency for your small speakers: 100 Hz Sends bass frequencies below 100 Hz to the subwoofer (or L speakers). 150 Hz Sends bass frequencies below 150 Hz to the subwoofer (or L speakers). 200 Hz Sends bass frequencies below 200 Hz to the subwoofer (or L speakers).
10 dB )
When is selected ( appears in the display), LFE is not available.
Front speaker distance setting
Default setting: 10 ft. Sets the distance from the front speakers to the listening position. Use or to set the distance of the front speakers from the main listening position (within a range of 0.5 ft. to 45 ft.).
Center speaker distance setting
Default setting: 10 ft. The center speaker is normally placed directly in the front of the listening room and closer to the listening position than the front speakers. This means that the sound from the center speaker will be heard before the front speakers. To prevent this, set the center speaker distance setting to delay the sound from the center speaker so that the sound from the front and center speakers will be heard at the same time. Use or to set the distance of the center speaker from the main listening position (within a range of 0.5 ft. to 45 ft.).
If all speakers (front, center, and surround) are set to L, the crossover frequency cant be set because there are no S speakers ( appears in the display).
Dynamic range control setting
When C is selected in the speaker setting, the center distance cant be set. Default setting: OFF Dynamic range is the difference between the loudest and softest sounds in any given signal. With this setting, you can compress the dynamic range, so that low level sounds can be heard more easily (sounding relatively louder) yet louder sounds wont be too overbearing. Press or to set the dynamic range control (OFF, MAX, or MID).
Surround speaker distance setting
Default setting: 10 ft. Like the center speaker, you should set the distance of the surround speakers accurately to hear sounds coming from both front and surround speakers at the same time. Use or to set the distance of the surround speakers from the main listening position (within a range of 0.5 ft. to 45 ft.).
When listening at low volumes, set to MAX for maximum dynamic range compression. Dynamic range control is effective only when a Dolby Digital signal is being played back.
When S is selected in the speaker setting, the surround distance cant be set.
Dual mono setting Subwoofer distance setting
Default setting: 10 ft. Like your speakers, you should set the distance of your subwoofer accurately to hear sounds coming from all speakers at the same time. Use or to set the distance of the subwoofer from the main listening position (within a range of 0.5 ft. to 45 ft.). Default setting: ch1 The dual mono setting can only be used when listening to Dolby Digital discs with dual mono encoding. These discs are not widely used, but are sometimes used when it is necessary to have one language on one channel and a different language on the other. With this setting you can choose which channel in the dual mono setting you want to listen to. If Dolby Digital mode is switched on, you will hear the channel you have selected (either ch1 or ch2) through your center speaker. With Dolby Digital mode off, or if you dont have a center speaker, you will hear the channel you have selected through both front speakers. In the Lch1.Rch2 setting, the left front speaker will play channel 1 and the right front speaker will play channel 2. Use or to cycle through the possible DUAL MONO settings.
When NO is selected in the subwoofer setting, the subwoofer distance cant be set.
Lch1.Rch2 ch2 ch1
Coaxial digital 2:
Default setting: CD Use or to assign the coaxial digital 2 input (DVD, TV, CD, CDR, DVR or OFF).
Component video input settings
VSX-D514 only Here you tell the receiver what components you have hooked up to the component video jacks on the back of the receiver.
Optical digital 1:
Default setting: TV Use or to assign the coaxial digital 1 input (DVD, TV, CD, CDR, DVR or OFF).
Component video 1:
Default settings: DVD Use or to assign the component video 1 input (DVD, TV, DVR or OFF). You can't assign two inputs to the same function. For example, assigning input 1 to the default setting of input 2 automatically switches input 2 to OFF.
Component video 2:
Default settings: TV Use or to assign the component video 2 input (DVD, TV, DVR or OFF).
Digital input settings
Here you tell the receiver what components you have hooked up to the coaxial and optical DIGITAL IN jacks on the back of the receiver. After you assign a component to a digital jack, whenever you select that component, (for example, a DVD player) the receiver automatically changes to the digital input setting and DIGITAL shows in the display.
Coaxial digital 1:
Default settings: DVD Use or to assign the coaxial digital 1 input (DVD, TV, CD, CDR, DVR or OFF).
03.12.5, 1:52 PM
Setting the relative volume level of each channel
Default setting: 0 dB For best surround sound playback, you should set the relative channel levels from the main listening position. You can set seperate levels for each surround mode.
If you dont hear a test tone from one of your speakers, please refer to Speaker setting on page 32 to make sure you have correctly specified your speaker setup. 3 Press VOLUME +/ to adjust the volume to an appropriate level. 4 Use LEVEL +/ to adjust the speaker levels in turn. You should hear the test tone at the same volume from each speaker when seated in the main listening position. The channel level range is 10 dB. 5 When youre done, press TEST TONE to turn off the test tone.
TEST TONE LEVEL EFFECT CLASS
TUNING STATION DISPLAY
The speaker volume can be adjusted without outputting the test tone by pressing CH SELECT and then using LEVEL +/. However, you can only adjust the level of the speakers currently active in the mode you're listening to. You can set separate levels for the STANDARD, STEREO and DVD 5.1 ch modes, as well as for each ADVANCED SURROUND mode.
1 Press STANDARD. You can also press ADVANCED SURROUND. 2 Press TEST TONE to output the test tone. The test tone is output in the following order (depending on the speaker setting):
Since the subwoofer transmits an ultra-low frequency its sound may seem quieter than it actually is. Using test tones to set up your speaker system will overwrite any previous settings you had for the STANDARD or ADVANCED SURROUND modes.
L SW 36
Switching the speaker impedance
We recommend using speakers of 8 with this system, but it is possible to switch the impedance setting if you plan to use speakers with a 6 impedance rating.
INPUT ATT FL
With the receiver in standby, press STANDBY/ON while holding down the SPEAKER IMPEDANCE button. Each time you do this, you switch between the impedance settings: SP 6 OHM Use this setting if your speakers are rated at 6. SP 8 OHM Use this setting if your speakers are rated at 8 or more.
Using the tuner
Listening to the radio
The following steps show you how to tune to FM and AM radio broadcasts using the automatic (search) and manual (step) tuning functions. Once you are tuned to a station you can memorize the frequency for recall latersee Saving station presets on the next page for more on how to do this.
Automatic tuning To search for stations in the currently selected band, press and hold the TUNING + / buttons for about a second. The receiver will start searching for the next station, stopping when it has found one. Repeat to search for other stations. Manual tuning To change the frequency one step at a time, press the TUNING + / buttons. High speed tuning Press and hold the TUNING + / buttons for high speed tuning. Release the button at the frequency you want.
Improving FM stereo sound
If the TUNED or STEREO indicators don't light when tuning to an FM station because the signal is weak, press the MPX button to switch the receiver into mono reception mode. This should improve the sound quality and allow you to enjoy the broadcast.
1 Press the FM or AM buttons to select the tuner. 2 Tune to a station. There are three ways to do this:
03.12.4, 7:50 PM
Saving station presets
If you often listen to a particular radio station, it's convenient to have the receiver store the frequency for easy recall whenever you want to listen to that station. This saves the effort of manually tuning in each time. This unit can memorize up to 30 stations, stored in three banks, or classes, (A, B and C) of 10 stations each. When saving an FM frequency, the MPX setting (see previous page) is also stored. Use the front panel controls to store station presets.
DVD/LD DVD 5.1 TV/SAT DVR/VCR
STATION TUNING STANDARD ADVANCED SURROUND STER DIRE
INPUT ATT FL DIMMER
1 Tune to a station you want to memorize. See Listening to the radio (previous page) for more on this. 2 If youre using the remote control, press RECEIVER. 3 Press TUNER EDIT. The display shows ST. MEMORY, then a blinking memory class.
STEREO TUNED SP A
4 Press CLASS to select one of the three classes then press } ] to select the station preset you want. You can also use the the MULTI JOG dial (front panel) to select a station preset. 5 Press ENTER. After pressing ENTER, the preset class and number stop blinking and the receiver stores the station.
Once you have named a station preset, you can press DISPLAY when listening to a station to switch the display between the name and the frequency.
Listening to station presets
Having stored up to 30 stations (see previous page), preset stations can be easily recalled.
Naming station presets
For easier identification, you can name your station presets. 1 Choose the station preset you want to name. See Listening to station presets (this page) for how to do this. 2 If youre using the remote control, press RECEIVER. 3 Press TUNER EDIT. The display shows ST. NAME, then a blinking cursor at the first character position. 4 Input the name you want. Names can be up to four characters long. Use the front panel MULTI JOG dial or the remote control } ] buttons to select characters. Press ENTER to confirm a character. If no character is input, a space is input. The name is stored when ENTER is pressed after choosing the fourth character.
1 Press the AM or FM buttons to select the tuner. 2 Press CLASS to select the class in which the station is stored. Press repeatedly to cycle through classes A, B and C. 3 Press STATION +/ to select the station preset you want.
If the receiver is left disconnected from the AC power outlet for an extended period, the station memories will be lost and will have to be reprogrammed.
To erase a station name, simply repeat steps 1-3 and input four spaces instead of a name.
Making an audio or a video recording
You can make an audio or a video recording from the built-in tuner, or from an audio or video source connected to the receiver (such as a CD player or TV) through the analog jacks. You will need to connect a CD recorder, tape deck, MD, VCR, or DVR deck to the CD-R/TAPE/MD or DVR/VCR outputs on the receiver to do so (see pages 1314 for more on this).
The receiver's volume, balance, tone (bass, treble, loudness), and surround effects have no effect on the recorded signal. 1 Select the source you want to record. Use the INPUT SELECTOR buttons to do this. 2 Select the input signal (if necessary). Press SIGNAL SELECT on the front panel to select the input signal corresponding to the source component (see page 29 for more on this). 3 Prepare the source you want to record. Tune to the radio station, load the CD, video, DVD etc. 4 Prepare the recorder (connected to either the CD-R/TAPE/MD or DVR/VCR outputs). Insert a blank tape, MD, video etc. into the recording device and set the recording levels. Refer to the instructions that came with the recorder if you are unsure how to do this. Most video recorders set the audio recording level automaticallycheck the components instruction manual if youre unsure. 5 Start recording, then start playback of the source component.
Incorrect operations are often mistaken for trouble and malfunctions. If you think that there is something wrong with this component, check the points below. Sometimes the trouble may lie in another component. Investigate the other components and electrical appliances being used. If the trouble cannot be rectified even after exercising the checks listed below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work. Problem The power does not turn on. Remedy Connect the power plug to the wall outlet. Disconnect the power plug from the outlet, and insert again. Make sure there are no loose strands of speaker wire touching the rear panel. This could cause the receiver to shut off automatically. Make sure the component is connected correctly (refer to pages 1217). Press MUTE on the remote control to turn muting off. Adjust the MASTER VOLUME. Make sure the component is connected correctly (refer to pages 1215). Select the correct component (use the INPUT SELECTOR buttons). Tune in the correct frequency. Connect the antenna (refer to page 16). Route any other cables away from the antenna terminals and wires. Fully extend the FM wire antenna, position for best reception, and secure to a wall. Connect an outdoor FM antenna (refer to page 16). Adjust the direction and position for best reception. Connect an additional internal or external AM antenna (refer to pages 16). Turn off the equipment causing the noise or move it away from the receiver. Place the antenna farther away from the equipment causing the noise. Connect an outdoor antenna (refer to page 16).
No sound is output when a function is selected.
No image is output when a function is selected.
Continuous Power Output (Stereo RMS) Front... 120 W (1 kHz, THD 0.2 %, 8 ) Continuous Power Output (Surround RMS) Front.. 120 W per channel (1kHz, THD 10 %, 8 ) Center. 120 W (1kHz, THD 10 %, 8 ) Surround. 120 W per channel (1kHz, THD 10 %, 8 ) Input (Sensitivity/Impedance) CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT.. 200 mV/47 k Frequency Response CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT.. 5 Hz to 100,000 Hz +0 dB 3 Output (Level/Impedance) DVR/VCR REC, CD-R/TAPE/MD REC.. 200 mV/2.2 k Tone Control BASS.. 6 dB (100 Hz) TREBLE.. 6 dB (10 kHz) LOUDNESS. +6.5 dB/+3 dB (100 Hz/10 kHz) (at volume level 50 dB) Signal-to-Noise Ratio (IHF, short circuited, A network) CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT... 96 dB Signal-to Noise Ratio [EIA, at 1 W (1 kHz)] CD, DVR/VCR, CD-R/TAPE/MD, DVD/LD, TV/SAT... 79 dB
Cleaning the unit
Use a polishing cloth or dry cloth to wipe off dust and dirt. When the surface is dirty, wipe with a soft cloth dipped in some neutral cleanser diluted five or six times with water, and wrung out well, and then wipe again with a dry cloth. Do not use furniture wax or cleansers. Never use thinners, benzine, insecticide sprays or other chemicals on or near this unit, since these will corrode the surface.
Input (Sensitivity/Impedance) DVR/VCR, DVD/LD, TV/SAT. 1 Vp-p/75 Output (Level/Impedance) DVR/VCR.. 1 Vp-p/75 Frequency Response DVR/VCR, DVD/LD, TV/SAT ] MONITOR. 5 Hz to 7 MHz +0 dB 3 Signal-to-Noise Ratio.. 55 dB Cross Talk.. 55 dB
Power Requirements. AC 120 V, 60 Hz Power Consumption.. 260 W In Standby... 0.5 W AC Outlet. 100 W MAX. (SWITCHED) Dimensions. 420 (W) x 158 (H) x 393 (D) mm (16-9/16 (W) x 6-1/4 (H) x 15-1/2 (D) in.) Weight (without package).. 9.3 kg (20.5 lb) Furnished Parts AM loop antenna.. 1 FM wire antenna.. 1 Dry cell batteries (AA size IEC R6). 2 Remote control... 1 Operating instructions.. 1 Warranty Card.. 1
FM Tuner Section
Frequency Range. 87.5 MHz to 108 MHz Usable Sensitivity. Mono:13.2 dBf, IHF (1.3 V/ 75 ) 50 dB Quieting Sensitivity.. Mono: 20.2 dB Stereo: 38.6 dBf Signal-to-Noise Ratio. Mono: 73 dB (at 85 dBf) Stereo: 70 dB (at 85 dBf) Distortion.. Stereo: 0.5 % (1 kHz) Alternate Channel Selectivity.. 60 dB (400 kHz) Stereo Separation.. 40 dB (1 kHz) Frequency Response. 30 Hz to 15 kHz (1 dB) Antenna Input (DIN). 75 unbalanced
Specifications and the design are subject to possible modifications without notice, due to improvements. * Measured pursuant to the Federal Trade Commissions Trade Regulation rule on Power Output Claims for Amplifiers. ** Measured by Audio Spectrum Analyzer.
XR-P350 Fostex X-77 RP200 PLC-XW50 ADZ628R RP300 SRM7500 10 CT-S630S LN510 CD1453B-02 Q1212 D-1200 BMW M5 Nikon FG WL-173 Review CT-WN4322Z DMX6fire2496 VSX-920-K DV6600 Nokia 3660 NS-C105 202mkiii RT21vhsw Tester C-480 Zoom CDX-GT55IP Evolution 2 SU-800 JBL L60T Linea 24 Printer AEG-electrolux BE12 RS22dcms 794MB X-FI 32GB 98128 DVP3580 MKB-300 RS20nrps Ellipse 605 HM25E 574CN KX-TG2224W PDP-615EX L64819 DSP-A5 21 Up0 HK-7X MVC-FD71 Kaleo WB660 HR-1000 Gpsmap60CS VFX-SD Masquerade-redemption 525 SX Trimmer Solar DSB-707 FTA Cry 2 GR-D30 HTR-5960 Nikon 995 KLV-17HR1 NP2500 12 Compressor Version 2 DXZ366MP Receiver 6455 RC Mcbr445W2 CXT85 TX-29PS2F V2 1 5100G LE40R51B S3400 Intuos PT-AE4000U FH-B700 SC-HTB500 HDR-CX500VE YZ85-2007 SSE-UMB-100 Ixus 300 Leicaflex SL2 System SGH-R210S Addenda MG105 EL-6890S EWF12670W FJ1254W Videostudio 7 63100X Helixboard18 HP-350 RL39ebns 9-3 2003 HD4646 DW130V
manuel d'instructions, Guide de l'utilisateur | Manual de instrucciones, Instrucciones de uso | Bedienungsanleitung, Bedienungsanleitung | Manual de Instruções, guia do usuário | инструкция | návod na použitie, Užívateľská príručka, návod k použití | bruksanvisningen | instrukcja, podręcznik użytkownika | kullanım kılavuzu, Kullanım | kézikönyv, használati útmutató | manuale di istruzioni, istruzioni d'uso | handleiding, gebruikershandleiding
1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101