ORDER NO.

RRV2529

DVD RECEIVER

XV-HTD1
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

Model XV-HTD1

Power Requirement

AC220V

Region No.

Remarks

This product is component of system.

Component

DVD SURROUND SYSTEM DVD RECEIVER SPEAKER SYSTEM XV-HTD1 S-HTD1 RRV2529 (RRV2460) RRV2456 This service manual

System

Service Manual
This service manual should be used together with the following manual(s):

Model No.

XV-HTD1/MYXJ

Order No.

RRV2460

CONTENTS

1. SAFETY INFORMATION.. 2 2. CONTRAST OF MISCELLANEOUS PARTS. 3 3. SCHEMATIC DIAGRAM.. 6 PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS (USA) INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936

PIONEER CORPORATION 2001

T ZZK AUG. 2001 Printed in Japan

1. SAFETY INFORMATION

WARNING THE AEL(ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS1. A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS FOR DVD : MAXIMUM OUTPUT POWER : 5 mW WAVELENGTH : 655 nm FOR CD : MAXIMUM OUTPUT POWER : 5mW WAVELENGTH : 785 nm

LABEL CHECK

Printed on the Rear Panel
Additional Laser Caution 1. Inside detection switch (S201 on the SMEB assy) and clampstatus detection switch (S11 on the TRSB assy) are detected by the microprocessor (IC11 in the DVDM assy). To permit the laser diode to oscillate, it is required to set the inside detection switch for the inside position (S201 : ON) and to set the loading-status detection switch for the clamp position (the center terminal of S11 is shorted to +3.3V). The 655 nm laser diode for DVD oscillation will continue if pin 19 of IC1 is shorted to +5V (fault condition) in the DVDM assy. The 785 nm laser diode for CD oscillates if pin 20 of IC1 is shorted to +5V in the DVDM assy. In the test mode , the laser diode oscillates when microprocessor detects a PLAY signal, or when the PLAY key is pressed (S5817 ON in the KEYB assy), with the above requirements satisfied. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. : Refer to page 74 on service manual RRV2460.
2. CONTRAST OF MISCELLANEOUS PARTS
NOTES: Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on product are used for disassembly. Reference Nos. indicate the pages and Nos. in the service manual for the base model. When ordering resistors, first convert resistance values into code form as shown in the following examples. Ex.1 When there are 2 effective digits (any digit apart from 0), such as 560 ohm and 47k ohm (tolerance is shown by J=5%, and K=10%). x 101 RD1/4PU 1 J 561 47k RD1/4PU 3 J 47 x 0.5 RN2H R K RRS1P 1 R 0 K 1R0 Ex.2 When there are 3 effective digits (such as in high precision metal film resistors). 5.62k 562 x RN1/4PC F

CONTRAST TABLE

XV-HTD1/NKXJ and MYXJ are constructed the same except for the following :
Part No. Ref. No. Mark Symbol and Description XV-HTD1 /MYXJ XWM3188 XWZ3433 XWZ3439 XWZ3443 XWZ3451 XWM3194 XWZ3456 XWX3031 XWX3040 XV-HTD1 /NKXJ XWM3192 XWZ3437 XWZ3441 XWZ3445 XWZ3452 XWM3196 XWZ3458 XWX3043 XWX3041 Remarks

P5- 2 P5- 3 P5- 4 P5- 6

PCB ASSEMBLIES NSP COMPLEX ASSY PRIMARY ASSY FRONT AMP ASSY REAR AMP ASSY MIC HP ASSY NSP CONNECT ASSY INPUT ASSY MAIN ASSY DSP ASSY PACKING SECTION Power Cord Packing Case NSP Warranty Card Operating Instructions (English) Operating Instructions (French/German/Italian) Operating Instructions (Dutch/Swedish/Portuguese) Operating Instructions (Spanish) Operating Instructions (Korean) Region Label (For Packing Case) EXTERIOR SECTION 5P F.F.C/60V 8P F.F.C/60V Rear Panel Caution Label Mic Knob FRONT PANEL SECTION NSP Front Panel Assy Front Cap Display Panel

P5- 7 P5- 9 P5-10

P3- 1 P3- 9 P3-12 P3-13 P3-14 P3-16 P3-17
ADG1154 XHD3193 ARY7022 XRB3006 XRC3034 XRC3035 XRC3036 Not used Not used
DDG1086 XHD3194 Not used Not used Not used Not used Not used XRC3039 VRW1702

P5-18 P5-18 P5-22 P5-37

XDD3093 Not used XNC3098 VRW1699 Not used
Not used XDD3092 XNC3105 VRW1886 XAB3014

P6- 5 P6- 6 P6- 7

XXG3072 XAK3212 XAK3214

XXG3073 XAK3211 XAK3215

Notes : For PCB ASSEMBLIES, Refer to CONTRAST OF PCB ASSEMBLIES and 3. SCHEMATIC DIAGRAM. The numbers in the remarks column correspond to the numbers on the EXPLODED VIEWS.

EXPLODED VIEWS

Front Panel 1
CONTRAST OF PCB ASSEMBLIES

K F INPUT ASSY

XWZ3458 and XWZ3456 are constructed the same except for the following :
Mark Symbol and Description
IC5353 C5241, C5247 C5242, C5248 C5271, C5272 R5241R5248 R9001, R9002

Part No. XWZ3456

Not used Not used Not used CCSRCH101J50 Not used RS1/16S0R0J

XWZ3458

BA4558F-HT CEAT100M50 CCSRCH470J50 CCSRCH221J50 RS1/16S332J Not used

O F MIC HP ASSY

XWZ3452 and XWZ3451 are constructed the same except for the following :
IC5802 C5805 C5806 C5807, C5812, C5813 C5808, C5814 C5809 C5810 C5811 R5814 R5866 R5867, R5872, R5874 R5868, R5885 R5869 R5870 R5871 R5873 VR5801 CN5807 CN5807 JA5801

Part No. XWZ3451

Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used Not used 52044-0545 Not used Not used

XWZ3452

BA4558F-HT CKSRYB681K50 CEAL1R0M50 CEAL100M16 CCSRCH101J50 CKSRYB471K50 CKSRYB104K25 CKSRYB473K25 RS1/16S101J RS1/16S222J RS1/16S104J RS1/16S223J RS1/16S224J RS1/16S681J RS1/16S102J RS1/16S0R0J XCS3005 Not used 52044-0845 XKN3008
5P FFC CONNECTOR 8P FFC CONNECTOR MINI JACK

G F FRONT AMP ASSY

XWZ3441 and XWZ3439 are constructed the same except for the following :

Symbol and Description

Part No. XWZ3439

Not used

XWZ3441

CEAT101M35

I F MAIN ASSY
XWX3043 and XWX3031 are constructed the same except for the following :
IC3002, IC3181 IC3151, IC3152, IC3161, IC3171 IC5701 C3011, C3014 C3185 C3186, C3187 C3913, C3914 C5701 C5702 C5704 C5705, C5706 C5707 C5708 C5830 C5831 R3181 R3182 R3183, R3184, R3254, R3258, R3263, R3264, R5703 R3186, R5705 R3189, R3190 R3255, R3257, R3259, R3261, R5702 R3256, R3260 R5558 R5559 R5701 R5830 R5831 CN5501 CN5502 KN5701 X5701

Part No. XWX3031

Not used NJM4558MD BU1923F Not used Not used Not used CKSRYB103K50 CKSRYB271K50 CEAT100M50 CKSRYB103K50 CCSRCH270J50 CKSRYB561K50 CKSRYB104K25 Not used Not used Not used Not used Not used RS1/16S0R0J Not used Not used Not used RS1/16S153J RS1/16S562J RD1/4PU101J Not used Not used 52045-0545 Not used VNF1084 ASS7004

XWX3043

BA4558F-HT BA4558F-HT Not used CEAT100M50 CEJQ100M35 CKSRYB473K25 CKSRYB102K50 Not used Not used Not used Not used Not used Not used CEAT101M10 CEAT101M25 RD1/4PU332J RS1/16S332J RS1/16S103J Not used RS1/16S682J RS1/16S473J RS1/16S182J RS1/16S123J RS1/16S153J Not used RS1/16S224J RS1/16S101J Not used 52045-0845 Not used Not used
5P FFC CONNECTOR 8P FFC CONNECTOR EARTH METAL FITTING CRYSTAL RESONATOR (4.332MHz)

H F REAR AMP ASSY

Although XWZ3445 and XWZ3443 are different in part number, they consist of the same components.

M F DSP ASSY

Although XWX3041 and XWX3040 are different in part number, they consist of the same components.

T F PRIMARY ASSY

Although XWZ3437 and XWZ3433 are different in part number, they consist of the same components.

3. SCHEMATIC DIAGRAM

3.1 MAIN ASSY (2/3)

I 3/3F

2/3 F MAIN ASSY (XWX3043)

I 1/3 I 3/3F

CN3702

K F CN5208

CN5351

I 2/3 F

Note : When ordering service parts, be sure to refer to "EXPLODED VIEWS and PARTS LIST" or "PCB PARTS LIST"

CN3301

CN3302

(VCB) (Y)

: HP AUDIO SIGNAL ROUTE : SL AUDIO SIGNAL ROUTE

(C) (SW)

: VCB SIGNAL ROUTE : Y SIGNAL ROUTE

: DVD AUDIO SIGNAL ROUTE

: SW AUDIO SIGNAL ROUTE
: DI AUDIO SIGNAL ROUTE : FL AUDIO SIGNAL ROUTE

: TX AUDIO SIGNAL ROUTE

: C SIGNAL ROUTE

: C AUDIO SIGNAL ROUTE

CN3502

CN3501

XV-HTD1 3.2 MAIN ASSY (3/3)

I 1/3 I 1/3 I 2/3F I 1/3

3/3 F MAIN ASSY (XWX3043)

I 2/3F

I 3/3 F

CN5801

CN5802

CN5807

1.6V 1.6V

2.5V 2.5V 0V

LEVEL SHIFT

3.1V 3.1V

CN3701

FOR DOWNLOAD

(VCB) (Y) (DVD)

: VCB SIGNAL ROUTE

: DVD AUDIO SIGNAL ROUTE : HP AUDIO SIGNAL ROUTE : TRAY POSITION SERVO LOOP LINE

(S) (T)

: Y SIGNAL ROUTE

: SEDO SERVO LOOP LINE

3.3 INPUT ASSY

K F INPUT ASSY (XWZ3458)

CN3703

CN5209

: The power supply is shown with the marked box.

(DVD) (AI) (TX)

(DI) (FL)
: AUX IN AUDIO SIGNAL ROUTE : AUX OUT AUDIO SIGNAL ROUTE

(AO) (TV)

: TV AUDIO SIGNAL ROUTE
3.4 FRONT AMP and MIC HP ASSYS

FRONT AMP ASSY (XWZ3441)

O F MIC HP ASSY (XWZ3452)

DC FAN MOTOR

CN5502

ORDER NO.

RRV2460

DVD RECEIVER

XV-HTD1
THIS MANUAL IS APPLICABLE TO THE FOLLOWING MODEL(S) AND TYPE(S).

MYXJ NVXJ

Model XV-HTD1

AC220-230V AC230V

Power Requirement

Region No.

Remarks
This product is component of system.

Component

DVD SURROUND SYSTEM DVD RECEIVER SPEAKER SYSTEM XV-HTD1 S-HTD1 RRV2460 RRV2456 This service manual

System

Service Manual

CONTENTS

1. SAFETY INFORMATION.. 2 2. EXPLODED VIEWS AND PARTS LIST.. 3 3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM. 10 4. PCB CONNECTION DIAGRAM.. 46 5. PCB PARTS LIST.. 66 6. ADJUSTMENT... 73 7. GENERAL INFORMATION.. 74 7.1 DIAGNOSIS.. 74 7.1.1 SELF-DIAGNOSTIC FUNCTION OF PICKUP DEFECTIVE.. 74 7.1.2 TEST POINTS LOCATION. 75 7.1.3 TEST MODE SCREEN DISPLAY. 7.1.4 POWER ON SEQUENCE.. 7.1.5 TROUBLE SHOOTING. 7.1.6 ERROR CODE.. 7.1.7 DISASSEMBLY. 84
7.1.8 TROUBLE SHOOTING FOR MECHANISM SECTION.. 95 7.2 PARTS... 98 7.2.1 IC... 98 7.2.2 DISPLAY.. 117 8. PANEL FACILITIES AND SPECIFICATIONS. 118
PIONEER CORPORATION 4-1, Meguro 1-chome, Meguro-ku, Tokyo 153-8654, Japan
PIONEER ELECTRONICS SERVICE, INC. P.O. Box 1760, Long Beach, CA 90801-1760, U.S.A. PIONEER EUROPE NV Haven 1087, Keetberglaan 1, 9120 Melsele, Belgium PIONEER ELECTRONICS ASIACENTRE PTE. LTD. 253 Alexandra Road, #04-01, Singapore 159936
c PIONEER CORPORATION 2001
T ZZK MAY 2001 Printed in Japan

1. SAFETY INFORMATION

WARNING THE AEL(ACCESSIBLE EMISSION LEVEL) OF THE LASER POWER OUTPUT IS LESS THAN CLASS 1 BUT THE LASER COMPONENT IS CAPABLE OF EMITTING RADIATION EXCEEDING THE LIMIT FOR CLASS1. A SPECIALLY INSTRUCTED PERSON SHOULD DO SERVICING OPERATION OF THE APPARATUS.
LASER DIODE CHARACTERISTICS FOR DVD : MAXIMUM OUTPUT POWER : 5 mW WAVELENGTH : 655 nm FOR CD : MAXIMUM OUTPUT POWER : 5mW WAVELENGTH : 785 nm

LABEL CHECK

Printed on the Rear Panel
Additional Laser Caution 1. Inside detection switch (S201 on the SMEB assy) and clampstatus detection switch (S11 on the TRSB assy) are detected by the microprocessor (IC11 in the DVDM assy). To permit the laser diode to oscillate, it is required to set the inside detection switch for the inside position (S201 : ON) and to set the loading-status detection switch for the clamp position (the center terminal of S11 is shorted to +5V). The 655 nm laser diode for DVD oscillation will continue if pin 19 of IC1 is shorted to +5V (fault condition) in the DVDM assy. The 785 nm laser diode for CD oscillates if pin 20 of IC1 is shorted to +5V in the DVDM assy. In the test mode , the laser diode oscillates when microprocessor detects a PLAY signal, or when the PLAY key is pressed (S5817 ON in the KEYB assy), with the above requirements satisfied. 2. When the cover is open, close viewing through the objective lens with the naked eye will cause exposure to the laser beam. : See page 74.
2. EXPLODED VIEWS AND PARTS LIST

NOTES:

Parts marked by "NSP" are generally unavailable because they are not in our Master Spare Parts List. The mark found on some component parts indicates the importance of the safety factor of the part. Therefore, when replacing, be sure to use parts of identical designation. Screws adjacent to mark on the product are used for disassembly.

2.3 FRONT PANEL SECTION

12 14(1/2)

14(2/2) 7
FRONT PANEL SECTION PARTS LIST

NSP NSP NSP NSP 9 10

JOG Assy KEYB Assy DISC KEY Assy STBY SWITCH Assy Front Panel Assy Front Cap Display Panel Front Panel Volume Knob Disc Button
XWZ3448 XWZ3447 XWZ3449 XWZ3453 XXG3072 XAK3212 XAK3214 XMB3052 XAA3020 XAD3093
Function Button Power Button Pioneer Badge Lens FL Filter Top Frame Leg Small Label Screw
XAD3100 XAD3101 XAM3001 XAX3216 XEC3015 XNG3063 AEB7090 XAX3291 VPZ30P080FZK
2.4 TABLE MECHANISM SECTION
37 (2/6 - 5/6) [Roller Cover] 37 (1/6) 43
37 (6/6) [PCB Cover] 18 7

From DVDM CN555

6 Refer to "2.5 TRAVERSE MECHANISM ASSY-S".

From DVDM CN2

TABLE MECHANISM SECTION PARTS LIST

NSP NSP NSP NSP NSP 43

5C Mech. Base Assy 5C Table Mech. Assy TRSB Assy SSRB Assy LOMB Assy Traverse Mechanism Assy-S Flexible Cable 24P Flexible Cable 8P (T) Flexible Cable 8P (M) Housing Assy 2P Slider Motor (LOADING) Motor Pulley Spring Floating Rubber Load Belt Clamper Plate Mechanism Base Clamper Float Base Clamper Holder Clamp Cam Planet Base Gear Pulley Loading Gear (1) Loading Gear (2) Drive Gear Change Gear Screw Screw Screw Motor (TRAY) Flexible Cable (7P) Motor Pulley Tray Belt Rubber Roller Roller Shaft Slide Table Motor Holder Worm Gear Tray Gear Screw Screw CR Cushion T2
XXA3027 VWT1175 XWZ3461 XWZ3462 XWZ3463 VXX2653 XDD3074 XDD3075 XDD3076 XDE3039 VXM1033 PNW1634 VBH1333 VEB1286 VEB1316 VNE2162 VNK4826 VNL1738 VNL1907 VNL1872 VNL1873 VNL1874 VNL1876 VNL1877 VNL1908 VNL1879 VNL1904 ABA7009 BPZ30P080FMC Z39-019 DXM1118 VDA1835 PNW1634 VEB1317 VEB1318 VLL1511 VNK4751 VNL1880 VNL1881 VNL1882 JGZ17P028FMC Z39-019 XEB3020
2.5 TRAVERSE MECHANISM ASSY-S

Top View

To DVDM Assy CN3
TRAVERSE MECHANISM ASSY-S PARTS LIST
NSP NSP NSP NSP NSP NSP 19 20
SMEB Assy FGSB Assy Motor (CARRIAGE) Motor (SPINDLE) Pickup Assy Table Sheet Screw Centering Spring Hook Spring Skew Spring Gear Spring Reflected Sheet Guide Bar Sub-guide Bar Hold Spring Magnet Holder Motor Base Cover Centering Ring Disc Table
VWG2048 VWG2009 VXM1079 VXM1084 VWY1055 DEC2040 VBA1058 VBH1278 VBH1317 VBH1303 VBH1308 VEC1959 VLL1504 VLL1505 VNC1017 VNE2070 VNE2154 VNE2155 VNL1746 VNL1747
Hook FFC Holder Mechanism Base FG Holder Gear A Gear B Gear C Slider Gear D Magnet Screw Screw Screw Magnet Holder Assy Spindle Motor Assy Carriage Motor Assy Screw

VNL1770 VNL1802 VNL1806 VNL1807 VNL1808 VNL1809 VNL1810 VNL1811 VNL1814 VYM1024 JFZ17P025FZK JGZ17P028FMC VBA1051 VXX2507 VXX2649 VXX2650 PBA1069

NSP NSP NSP NSP

3. BLOCK DIAGRAM AND SCHEMATIC DIAGRAM

3.1 BLOCK DIAGRAM

(24P) RF B1 B2 B3 B4

DVDM ASSY

RFO DSP RF BH PH FE TE 27M 16M

Spindle Motor

PICKUP ASSY
RF B1 B2 B3 B4 F DRV T RTN T DRV F RTN

IC1 LA9701M RF IC

57-60 IC12 63-66 PE5108A DVD DECODER BY CHIP 55 12
SD0-SD7 CDDATA SREQ XSACK

80-84 78,86,91 89

IC18 MB86373B MPEG2 DECODER AV-1

27M 36/16M

IC15 MN414800CSJ-07 4M DRAM
IC19 MB811171622A-100FN 16M SDRAM

SPDL+ SPDLSLDR R SLDR F

48 SLDO 45 SPDO 46

TDO FDO

IC3 M56788FP SPDL & FTS DRIVER

IC2 LC78652W SERVO DSP

16M LODDRV

Carriage Motor

D SMEB ASSY

LODDRV

IC11 PD3410A SYSTEM CONTROL CPU
IC14 KM68V1000CLT-7L WORK SRAM (1M)
IC13 VYW3003 FLASH MEMORY (8M)

LOADLOAD+ 27M 16M 36/16M

Loading Motor
DISC SENS LOAD POS TRAY POS

PC21 PC22

S21 LOADING POSITION DET. SW

LOMB ASSY

IC21 BU2288FV CLOCK GENERATOR

TRSB ASSY MAIN ASSY

(7P) DISC CLAMP DET. SW

CN8902

DISC SENS CLAMP TRAY POS LOAD POS

JA5201 TV/VCR IN

IC5231 BU4052BCF AUDIO SELECTOR

11 IC5352-1/1 3

CN5207

AUX IN AUX OUT

SEDR+ SEDR-

CN21 CN12

CN8903
IC8901 BA6195FP 13 5DISC TURN DRIVER

CN5208

(19P) TXL

K INPUT ASSY

TRAY Motor

SSRB ASSY

KEYB ASSY

TUNER (13P) MODULE

Q STBY SWITCH ASSY

N DISPLAY ASSY

V5801 XAV3011 FL TUBE

CN5801

J5808 CN5806

CN5803

CN5802

S DISC KEY ASSY

Foot of R261 (FPWM) V: 1V/div. H: 5msec/div.
IC18 - pin 36 (C output) V: 0.2V/div. H: 5msec/div.
IC18 - pin 39 (Y output when selecting color difference output) V: 0.2V/div. H: 5msec/div.

GND GND GND GND

TP2 (RFO) V: 500mV/div. H: 0.1sec/div.
Foot of R262 (VPWM) V: 1V/div. H: 5msec/div.
IC18 - pin 45 (CB output when selecting color difference output) V: 0.2V/div. H: 5msec/div.
IC18 - pin 36 (CR output when selecting color difference output) V: 0.2V/div. H: 5msec/div.

GND GND GND

TP3 (Tracking Error) (AI-Inner Tracking Off) V: 500mV/div. H: 2msec/div.
Foot of R263 (PPWM) V: 1V/div. H: 5msec/div.
CN55 - pin 5 (DISC SENS) V: 2V/div. H: 1sec/div. CN55 - pin 2 (TRAY POS) V: 2V/div. H: 1sec/div.
IC2 - pin 39 (EFM before slice) V: 1V/div. H: 1sec/div.
Foot of R264 (RPWM) V: 1V/div. H: 5msec/div.

GND GND

IC2 - pin 1 (EFM) V: 1V/div. H: 0.2sec/div.
IC18 - pin 45 (Composite Video output) V: 0.2V/div. H: 1msec/div.
CN55 - pin 4 (SED0) V: 2V/div. H: 5sec/div. CLOSE OPEN DISC CHANGE
IC3 - pin 41 (REGB) V: 1V/div. H: 5msec/div.
IC18 - pin 39 (Y output) V: 0.2V/div. H: 5msec/div. Tray Close

VOLTAGES

I 3/3 MAIN ASSY

IC5501 (PDC076A)

Pin No. 25 Voltage (V) 4.8 4.8 3.3 4.8 4.8 4.8 4.8 4.8 3.3 3.4 4.3.2.5 2.5 4.8 4.8 4.0 4.8 0.2 4.7 Mode: DVD Play Pin No. 50 Voltage (V) 2.0 4.6 4.8 Pin No. 75 Voltage (V) -30.8 0 5.0 4.0 4.8 4.0 Pin No. 100 Voltage 0 4.7 4.7 4.4.0 4.0 4.0 4.4.8 4.6
Note : FL drive voltage, pulse waveform of Low level is VFDP (about -31V) and High level is VDD (+5V).
4. PCB CONNECTION DIAGRAM

NOTE FOR PCB DIAGRAMS :

1. Part numbers in PCB diagrams match those in the schematic diagrams. 2. A comparison between the main parts of PCB and schematic diagrams is shown below.
Symbol In PCB Diagrams Symbol In Schematic Diagrams B C E B C E Part Name
3. The parts mounted on this PCB include all necessary parts for several destinations. For further information for respective destinations, be sure to check with the schematic diagram. 4. View point of PCB diagrams.

Connector

Transistor

Capacitor

B C E B B C E D D G S G S D G S C E B C E

SIDE A

Transistor with resistor

Field effect transistor

P.C.Board

Chip Part

SIDE B

Resistor array

3-terminal regulator
4.1 TRSB, SSRB, LOMB, SMEB and FGSB ASSYS

A TRSB ASSY

(XNP3042-A)

I CN8903

TRAY MOTOR

B SSRB ASSY

LOADING MOTOR
D CARRIAGE MOTOR (VNP1722-A)

BLK RED

C LOMB ASSY

E FGSB ASSY

SPINDLE MOTOR

(VNP1784-A)

A B C D E

4.2 TUNER MODULE

J TUNER MODULE

I CN5701

(ANP7338-B)
Q201 IC201 Q203 IC202 Q205 Q204

4.3 DVDM ASSY

F DVDM ASSY

Q3 IC23

Q121 Q101 Q7 Q6

Q103 Q5 Q102

IC1 Q109

Q81 Q91 Q83

(VNP1817-A)

I CN8902

SIDE B C

I CN8502

IC13 IC14

Q114 Q113

D CN202

Q106 IC26 IC27

I CN8501

4.4 FRONT AMP ASSY

G FRONT AMP ASSY

Q3714 Q3713 IC3301

IC3321

CN3053

Q3351 Q3352

(XNP3044-C)

Q3703 Q3705 Q3715

Q3603 Q3302 Q3301

Q3711 Q3712
Q3717 Q3716 Q3773 Q3771 Q3774

4.5 REAR AMP ASSY

Q3813 Q3702

IC3322

IC3401

IC5021

CN3054

IC5007

Q3816 Q3817 Q3811 Q3704 Q3706 Q3812 Q3452 Q3815

REAR AMP ASSY

Q3501 Q3401

D (XNP3044-C)

XV-HTD1 4.6 MAIN ASSY

I MAIN ASSY

G CN3302

H CN3502

M CN3701

J CN201

IC3002 IC3151 IC3152 IC3171 IC3181 IC3161 Q5721

O CN5807

IC15 IC14 IC13 IC18

F CN15

F CN55

A CN11

8 IC17
Q5501 Q5072 IC5001 IC5004
IC5005 IC5071 Q5071 Q5031 IC5081 Q5041

(XNP3043-D)

IC8521 IC8541 Q5042 IC5081 Q5032

IC5501 IC8531

This function is effective only for DVD pickup (650nm).
Character in bold : Item name : Information display
Laser diode current value

Test Mode Screen Display

7.1.2 TEST POINTS LOCATION

CN5 CN2

Front Side

VCODR IC13 IC14

CN4 IC2

TP3 (TE) IC19

TP1 (FE) VREF
TP2 (RFO) VREF CN3 TP4 (FDO)
CN1 R389 Short-circuit at diagnosis
7.1.3 TEST MODE SCREEN DISPLAY TEST MODE SCREEN DISPLAY
Consecutive double-OSD display is supported during test mode. The screen is composed 10 lines with a maximum of 32 characters per line. It can't be used with the debugging display mode together.

Screen Composition

Address Background color Tracking status and Laser diode current value Spindle status and AFB status AGC setting FTS servo IC information C1 error value of CD and DVD Internal operation mode of the mechanism control Disc judgment and CD 1/3 beam switch jitter value
Remote control code Key code Mechanism position value and slider position
AV1 chip version FL controller version and region setting for the player FL controller destination setting Port No. of Flash ROM and system controller Flash ROM version and Flash ROM size System controller revision DVD mechanism controller revision (Control and part No. of GUI-ROM)

First Screen Display

Caution : The first screen and second screen switch by pressing [DISPLAY] key of the remote control unit. It is only a version display part on the lower right of the screen those contents of display change. ATB : ON/OFF information display and AGC manual setting display deleted with the second generation. The displays of Tilt error value, Tilt servo status and pickup DVD/CLD display deleted with the third generation becomes LD part is deleted.
Description of Each Item on the Display
(1) Address indication The address being traced is displayed in number. DVD : ID indication (hexadecimal number, 8 digits) [] CD : A-TIME (min. sec.) [0000] (Note : For DVDs, decimal-number indication is possible.) (2) Code indication of the remote control unit [R ] The code for the key pressed on the remote control unit, which is received by the FL controller, is displayed while the key is pressed. In the case of the double code, the second code will be displayed. (3) Key code indication for the main unit [K ] The code for the key pressed on the main unit, which is received by the system controller, is displayed while the key is pressed. (4) Background color indication [C R G B ] (5) 1 Tracking status [TRKG ] Tracking on [ON ] Tracking off [OFF] 2 Laser diode current value [LDI ]
(6) 1 Spindle status [SPDL ] Spindle accelerator and brake, free-runnimg FG servo Rough, velocity phase servo Offset addition, rough, velocity phase servo 2 AFB status [AFB ] ON OFF (7) Mechanism position value [M ] Position code (8) Slider position [S ] CD TOC area CD active area (9) AGC setting [AGC ] AGC on AGC off

[A/B] [FG] [SRV] [O_S] [ON ] [OFF]

[1] to [7]

[IN ] [CD ]

[AGC-ON] [AGC-OFF]

(10) Output video system [V ] NTSC system PAL system Auto-setting

[NTSC] [PAL ] [AUTO]

(20) 1 Version of the flash ROM [V : . ] 2 Flash ROM size [FLSH = ] (21) Revision of the system controller [S : . / . ] 1 Revision number of the external ROM part (flash ROM) of the system controller <Front> 2 Revision of the internal ROM part of the system controller <Rear> (22) Revision of the DVD mechanism controller [M : . ] Revision number of the external ROM part (flash ROM) of the DVD mechanism controller (23) Control and part numbers of the GUI-ROM [GUI : ] No GUI model displays as " / ". OEM model displays the part number of GUI-ROM [GUI : * * * *]
(11) FTS servo IC information DSP coefficient indication [KS [ ] ] Displays the address (four digits) of the specified coefficient and the setting value (four digits) with [TEST] and [9] keys. (12) Error rate indication 1 C1 error value of CD 2 C1 error value of DVD [ER C1 ] [ER ]
(13) Internal operation mode of mechanism controller [MM : ] Internal mechanism mode (2 digits) and internal mechanism step (2 digits) of the mechanism controller (14) 1 Disc sensing [DSC ] The type of discs loaded is displayed. [DVD], [CD ], [VCD], [ ] 2 CD 1/3 beam switch [BM ] (15) Jitter value [J ] CD is effective only in the jitter value. (16) Version of the AV-1 chip [ AV : . ' ' ] (17) 1 Version of the FL controller [FL : ] 2 Region setting of the player [REG : ] Setting value

[1] to [6]

(18) Destination setting of the FL controller [MDL : / ] For characters in front represent the type of model : There characters that follow represent the destination code. J : /J, K : /KU, /KC, /KU/KC, R : /RAM, /RL, /RD, /LB, WY : /WY (19) The part number of the flash ROM and system controller [ / ] 1 Part number of the flash ROM <Front> (Example) VYW1536-A = W1536A (Example) PD6256A9 = 6256APart number of the system controller <Rear> (Example) PD3381T1 = 3381T1

DVD does not operate at all. Time is not displayed in FL DISPLAY at the DVD function.
It does not communicate with the DVD microcomputer.
Whether terminal (27Pin, 83Pin, 98-100Pin) for the communication with the DVD microcomputer does the communication operation is confirmed. If the communication operation is not done, whether the B to B connector etc. are disconnected is confirmed. Whether "H" is output to terminal DVDRESET (87Pin) is confirmed.
The operation key is not accepted at all.
It is recognized that other KEY has already been pushed.
When KEY is not pushed, whether KEY input terminal (18Pin, 22Pin) is 5V is confirmed. If the KEY input terminal is not 5V, whether KEY SW on the line breaks is confirmed.

7.1.6 ERROR CODE

Error codes that are displayed on the FL display without using the remote control unit

FL Display

AV1 VER CPU AERR DMA AERR FLASH ID FLASH WRP FLASH SIG FLASH SUM FLASH SIZE ILLGAL RESERVE SLOT DVD ERR CT FAN ERR

Possible causes

AV-1 chip is not a match with the program of system controller CPU address error (Hardware is unusual.) DMA address error (Hardware is unusual.) Difference in versions of the internal ROM of the system controller and of the flash ROM, or bus line failure or reverse installation Write protect error of the flash ROM Difference in part number of the flash ROM (When the ROM which couldn't be used was used.) Check sum error of the flash ROM (It exceeds the regular size.) or reverse installation (Hardware is unusual.) Size error of the flash ROM (Use 4 or 8 M-bit.)

Operation of the unit

The sound may not produced with the specific audio.
No operation No operation No operation No operation No operation No operation No operation
The system controller fetched a code other than an operation code (Hardware is unusual.) No operation Undefined interrupt (Hardware is unusual.) Inappropriate slot command issued (Hardware is unusual.) No operation No operation
This display appears when the terminal of microcomputer PIN.No13 becomes 2.9V or less No operation and the set enters the standby state. display appears when the terminal of microcomputer PIN.No21 becomes more than 2.5V (fan abnormality), and the set enters the state of the standby. No operation

F5 Tray being pushed

The tray switch that had been Open mode was forcibly changed to a mode other than Closes Open by an external force. Reverses the loading Loading, unloading or clamping could not be completed within a specified time (about direction. It timeout is 5 seconds). repeated upon retry, the unit stops. The following error occured eight times. (1) Focus ON sequence could not be completed even if more than two seconds after the focus ON command (to the servo DSP) was sent. (2) Focus IN sequence was finished, actually focus IN was not completed. Stops wherever possible then opens (stops in the case of side B).

F8 Loading timeout

FC Focus
Error codes that are displayed on the FL display by using the remote control unit (Device error) To display : ESC + DISPLAY + DISPLAY ; Location of the display : At the two digits of left of the FL display
FL Description of Error Causes if with a DVD Causes if with a CD Operation of the Unit
No operation or it becomes debugging indication if the power is able to ON. AV1 access error bit3=etc. (read, write NG) bit2=etc. MY CHIP access error bit1=etc. SRAM access error
7.1.7 DISASSEMBLY DIAGNOSIS OF PCBs
Note When diagnosing the unit, be sure to use two connection cables for service. (Part No : GGD1228) DVDM Assy
Remove the Bonnet (Screws 7) Power ON Tray Open (0 OPEN/CLOSE) Remove the Tray Cap

Tray Cap

DVDM Assy

Insullation Sheet

Rotary Tray
Connect two Connection Cables for Service (GGD1228)
Attention: Be carefull not to put the flexible cables when closing the tray
Power OFF (Pull out the Power Cord from the outlet.) Remove one Screw Remove one DV Brackets (one screw) Unhook two PCB Supports (Remove FFC Cable (CN5807)) Remove the DVDM Assy (Connectors 2) Test Disc PCB Support
Cutting Pliers Put the Power Cord in the outlet Power On Tray close (Automatically) Press the EXCHANGE Button (clamp the Test Disc 16 -1 Tray Open)

Diagnosis

FRONT PANEL SECTION TABLE MECHANISM SECTION
Remove the Bonnet (Screws 7) Power ON Tray Open (0 OPEN/CLOSE) Remove the Tray Cap Close the tray Power OFF (Pull out the Power Cord from the outlet.)
Turn the Pickup Short SW to Short side.

Pickup Flexible Cable

Short SW

Unhook Unhook

Remove the Front Panel section Refer to the " TRAVERSE MECHANISM ASSY-S" section.
STBY SWITCH KEYB Assy Assy JOG Assy DISC KEY Assy
11 Put the Power Cord in the outlet 12 Power ON

Remove four connectors.

How to Open the Tray by Manual Operating

Gear Pulley

CN8903 CN555

Tray Open

Flexible Cable (7P) : VDA1835 (TRSB CN12 SSRB CN21)

7.2 PARTS

7.2.1 IC
The information shown in the list is basic information and may not correspond exactly to that shown in the schematic diagrams.

List of IC

LC78652W, PD3410A, MB86373B, PDC076A, BA6195FP, AK4527BVQ, LC89056W-E, STK413-000
LC78652W (DVDM ASSY : IC2)

Servo DSP IC

Block Diagram
FE 33 TE 32 TILTE 29 RF_PH 30 RF_BH 31 JITT 28 MPX 8bit A/D Servo Processor (1616+3232) 8bit D/A
47 FDO 48 TDO 45 SLDO 46 SPDO 44 TBAL 43 TILTDO 42 AUXO

HFLIO 51

24 DRF
TES 26 PP2/EVENT 56 FG 55 SLCIST1,2 34,35 EFMIN 39 SLCO1,2 36,37 EFMOUT 1 PCKIST1,2 87,88 DVDFR 90 CDFR 91 PD01-3 83-85 JV 92 DVDSYNC 96 PCK 93 LEFM
Track Counter Event Counter

22 FAST

95 DVDSYEQ

FG Counter

23 V_PB
DVD Lock Detection PLL Sub Code Decode CRC
21 FSEQ 77 WRQ 74 SQOUT 75 CQCKB 76 RWC 17 EMPH 12 PW 10 SBCK 18 SBSY 11 SFSY
Frame Synchronous Detection, Protection, Insertion EFM Demodulation
LEFMVPDO 81 VCOC 80 XIN 14 XOUT 15 XTALOUT 8 ADRAO 94 CSB 58 WRB 60 RDB 59 P0-7 63-70 BUSYB 73 LASER 52 FBUSYB 7

53,54 PP0-3 ,56

Clock Generator
Error Detect Correction C1-Twofold, C2-Fourfold
For De-Interleave 16k SRAM

9 FSX 20 EFLG

5 LRSY

Command Interface

Supplement/Mute D Attenuate Deemphasis Filter

4 ROMCK

Serial Out

3 ROMXA 2 C2F

19 DOUT 25,27 38,50

TEST1-4

General Purpose Register

57 RESB

Pin Function
No. 9 Pin Name EFMOUT C2F ROMXA ROMCK LRSY PP3 FBUSYB XTALOUT FSX I/O O O O O O O O O I O O I O O O O O O O O O I I I I I I I I I O O I I O O O O O O O I Output the state that was binary-stated value EFM C2 flag output CD-ROM data output Shift clock output for CD-ROM data output L/R clock output for CD-ROM data output N ch-OD output Busy signal output of DSP process operation External system clock output CD 1 frame sync. signal output Subcode reading out clock input Frame sync. signal output of subcode Subcode P, Q, R, S, T, U, V and W output GND pin Connect a crystal resonator (16.9344MHz) Connect a crystal resonator 3.3V power supply of the oscillation circuit Monitor pin of the deemphasis Sync. signal output of the subcode block Audio EIAJ data output Error correction state monitor of the error correction C1 and C2 Detection monitor of the CD/DVD frame sync. signal Playback speed monitor In focus monitor Test input 3 Tracking error signal input Test input 2 Jitter quantity detecting signal input of EFM PLL Tilt error signal input RF peak hold signal input RF bottom hold signal input Tracking error signal input Focus error signal input Current setting pin 1 of the constant current charge pump for SLC Current setting pin 2 of the constant current charge pump for SLC Control output 1 for SLC Control output 2 for SLC Test input 1 EFM/EFM + input 5V power supply of A/D and D/A for servo GND of A/D and D/A for servo DA auxiliary output Tilt control signal output Tracking balance control signal output Sled control signal output Spindle control signal output Focus control signal output Tracking control signal output Reference level of D/A for servo Test input 4 N ch-OD output Monitor output of the rough servo/CLV control N ch-OD output Function

I/O General-purpose port input/output / DVD sync. signal input
10 SBCK 11 SFSY 12 PW 13 VSS 14 XIN 15 XOUT 16 DVDDEMPH 18 SBSY 19 DOUT 20 EFLG 21 FSEQ 22 FAST 23 V_PB 24 DRF 25 TESTTES 27 TESTJITT 29 TILTE 30 RF_PH 31 RF_BH 32 TE 33 FE 34 SLCISTSLCISTSLCOSLCOTESTEFMIN 40 AVDD 41 AVSS 42 AUXO 43 TILTDO 44 TBAL 45 SLDO 46 SPDO 47 FDO 48 TDO 49 VREF 50 TEST4

Pin Name

I/ O I/O Mirror detection signal input/output O Output pin for laser ON/OFF control

Function

51 HFLIO 52 LASER 53 PP0/DVD_CDB 54 PP1/CRCERRB 55 FG 56 PP2/EVENT 57 RESB 58 CSB 59 RDB 60 WRB 61 DVDDVSS 63 PPPPPPPPVSS 72 DVDDBUSYB 74 SQOUT 75 CQCKB 76 RWC 77 WRQ 78 AVSS 79 VRPFR 80 VCOC 81 VPDO 82 AVDD 83 PDOPDOPDOAVSS 87 PCKISTPCKISTAVDD 90 DVDFR 91 CDFR 92 JV 93 PCK 94 ADRAO 95 DVDSYEQ 96 DVDSYNC 97 LEFMDVDDVSS 100 LEFM
I/O General-purpose port input/output / Disc discrimination signal output I/O General-purpose port input/output / Subcode CRC result signal output I I I I I FG counter input Reset input Chip select input Internal state reading signal input Command / data writing signal input 5V power supply GND I/O General-purpose port input/output / Event counter input
I/O Command / data input/output

O O I I O I O

GND 3.3V power supply for internal Busy signal output of command process Serial output of subcode Q Shift clock input for subcode Q data output Update permission input of subcode Q Read out ready monitor of subcode Q PLL GND for internal system clock VCO oscillation range setting of PLL for system clock Connect a PLL filter for system clock PLL 5V power supply for system clock
I/O PLL filter connection pin 1 for EFM playback I/O PLL filter connection pin 2 for EFM playback I/O PLL filter connection pin 3 for EFM playback O O I I I O O PLL GND for EFM playback Current setting 1 of PLL constant current charge pump for EFM playback Current setting 2 of PLL constant current charge pump for EFM playback PLL 5V power supply for EFM playback VCO oscillation range setting of PLL for EFM playback 1 VCO oscillation range setting of PLL for EFM playback 2 Jitter output of PLL clock for EFM playback Bit clock output for EFM playback Address input DVD synchronize pulse input DVD synchronous signal input Output the state that cut and out a signal which was binary-stated value EFM with PCK 2 3.3V power supply for I/O GND Output the state that cut and out a signal which was binary-stated value EFM with PCK 1
PD3410A (DVDM ASSY : IC11)

System Control IC

Pin Function
GND CK VCC PICLK PIDATA GND PORTH0 PORTH1 PORTH2 PORTH3 VCC PORTH4 PORTH5 PORTH6 PORTH7 GND EXTAL XTAL VCC PORTG0 PORTG1 PORTG2 PORTG3 PORTG4 GND PORTG5 PORTG6 PORTG7 PORTF0 PORTF1 PORTF2 VCC PORTF3 PORTF4 PORTF5

XCS3/XCASL

XCS3 GND V+3D GND V_SEL2 V+3D GND EXTAL XTAL V+3D XCSDF0 XCSDF1 LFEON GND 6CHMD XAMUTE 44X48 V+3D XAVSRST DSCSNS

10 N.C. 11 N.C. 12 DROUT13 DROUT+

DROUT+ 13

OPOUT 1

N.C. 2

N.C. 3

BIAS 4

DRIN' 5

DRIN 6

N.C. 7

N.C. 8

N.C. 9
AK4527BVQ (DSP ASSY : IC3751)
High Performance Multi-channel Audio CODEC

Audio I/F

LIN+ 30 LIN- 29 RIN+ 32 RIN- 31

ADC ADC

HPF HPF

LOUT1 27

MCLK LRCK BICK

ROUT1 28

39 MCLK 5 LRCK 4 BICK 10 DAUX

LOUT2 25

DATT Format Converter

ROUT2 26

DATT SDOUT 1 SDOS 9 SDTO

LOUT3 23

DATT SDIN1 SDIN2 SDIN3

ROUT3 24

6 SDTISDTISDTI3
SDOS I2C SMUTE BICK LRCK SDTI1 SDTI2 SDTI3 SDTO DAUX DFS NC DZFE TVDD DVDD DVSS PDN
I I I I I I I I O I I I I SDTO source selection
L: Internal ADC output, H: DAUX input Serial control mode selection L: 3-lines serial, H: I2C bus Soft mute H: Start the soft mute, L: Cancel Audio serial data clock Input channel clock DAC1 audio serial data input DAC2 audio serial data input DAC3 audio serial data input Audio serial data output Auxiliary audio serial data input Double speed sampling mode No connect Effective pin of zero input detection function L: mode 7 (disable) at parallel mode and selectable with DZFM2-0 at serial mode H: mode 0 (Output it from DZF1 with AND of 6ch) Power supply for output buffer, 2.7V to 5.5V Digital power supply, 4.5V to 5.5V Digital ground, 0V Power down & reset It becomes powered down state when turns this pin into L, and a register is initialized. Reset it with PDN pin when switched P/S and CAD0-1. L: Normal speed, H: Double speed
TST NC ADIF CAD1 CAD0 LOUT3 ROUT3 LOUT2 ROUT2 LOUT1 ROUT1 LINLIN+ RINRIN+ DZF2
I I I I O O O O O O I I I I O O O I O I I I I I I I I Test pin Connect to DVSS. No connect
Analog input form selection H: Differential input, L: Single end input Chip address 1 pin Chip address 0 pin L ch analog output of DAC3 R ch analog output of DAC3 L ch analog output of DAC2 R ch analog output of DAC2 L ch analog output of DAC1 R ch analog output of DAC1 L ch analog inverting input L ch analog non-inverting input R ch analog inverting input R ch analog non-inverting input Zero input detection 2 It becomes H when the input data of group 2 is 8192 times of zero continuously or RSTN bit is 0. Analog input overflow detection It becomes H when analog inpu of L ch or R ch is overflowed. Common voltage input, AVDD/2 Install a capacitor which is high capacitance (about 2.2F) to eliminate the power supply noise. Reference voltage input, AVDD Analog power supply, 4.5V to 5.5V Analog ground, 0V Zero input detection 1 It becomes H when the input data of group 1 is 8192 times of zero continuously or RSTN bit is 0. Master clock input Parallel / serial selection L: Serial control mode, H: Parallel control mode Audio data interface format 0 (at parallel control mode) Chip select (at 3-lines serial control mode) Connect to DVDD at I 2 C bus control mode. Audio data interface format 1 (at parallel control mode) Control data clock (at serial control mode) I2C= L: CCLK (3-lines serial), I2C=H: SCL (I 2 C bus) Loop back mode 0 (at parallel control mode) Validate the digital loop back from ADC to all DAC. loop back mode 1 Input from SDTI1 to all DAC.

STK413-000 (FRONT AMP ASSY : IC3301)

Power Amplifier

CH2+VE Pre -VH
R11 C11 TR12 C12 R14 D2 R3 TR6 R1 C1 TR4 TR3 TR19 R13 TR16 R15 R16 R17 TR1 TR2 TR17 TR20 D41 Comparator TR14 TR15 R12 TR41 R41

CH1 IN

CH3 IN

TR11 TR13

CH2 IN

3 +V ref

D42 D43 D44
CH1 NF 14 BIAS 15 CH2 NF 16
R5 D51 R6 TR5 D1 TR7 TR10 TR29 TR30 TR27 TR28 R23 TR26 R24 C22 D4 TR22 TR21 C21 R21 TR23 TR25 R22 TR24 R25 R51 R26 TR51 R27 D54 D53 D52

4 -V ref

Comparator

Pre-VH

CH1-VE CH1+VE

CH3-VE CH3+VE

7.2.2 DISPLAY XAV3011 (DISPLAY ASSY :V5801)

FL DISPLAY

f g e r d2 s pn d1 a2 h a1 jk b m c

Pin Assignment

(3G - 13G)

ALL DISCS RANDOM REPEAT

MIDNIGHT CONDITION ANGLE LAST MEMO

L C R LFE

Ls S Rs

Anode Connection

13G P1 P2 P3 P4 P5 P6 P7 P8 P9 P10 P11 P12 P13 P14 P15 P16 P17 P18 a1 a2 b h j k f g s m c r p n e d1 d2 12G S1 a1 a2 b h j k f g s m c r p n e d1 d2 a1 a2 b h j k f g s m c r p n e d1 d2 11G 10G S2 a1 a2 b h j k f g s m c r p n e d1 d2 a1 a2 b h j k f g s m c r p n e d1 d2 a1 a2 b h j k f g s m c r p n e d1 d2 9G 8G 7G S3 a1 a2 b h j k f g s m c r p n e d1 d2 6G col2 a1 a2 b h j k f g s m c r p n e d1 d2 5G S4 a1 a2 b h j k f g s m c r p n e d1 d2 4G col1 a1 a2 b h j k f g s m c r p n e d1 d2 3G S5 a1 a2 b h j k f g s m c r p n e d1 d2 2G REPEAT RANDOM 1G MIDNIGHT CONDITION ANGLE LAST MEMO

S DISC ALL

Pin Connection
Pin No. Connection Pin No. Connection Pin No. Connection 1 FP2 F8G 52 7G 53 6G 54 5G NX 55 4G 56 3G 15 P57 2G 16 PPPP61 FP62 FPNX NP NP P18 P17 P16 P15 P14 P13 P12 P11 P10 P9
NX NX NX NX NX NX NX NX NX NX NX
NX NX NX NX NX NX NX 1G NP NP
Note (1) F1, F2 : Filament (2) NP : No pin (3) NX : No extend pin (4) DL : Datum Line (5) 1G to 13G : Grid
NX NX NX 13G 12G 11G 10G 9G
8. PANEL FACILITIES AND SPECIFICATIONS

8.1 PANEL FACILITIES

Front Panel

0 OPEN/CLOSE

DISC SKIP EXCHANGE 5

VOLUME

DVD RECEIVER XV-HTD1

STANDBY/ON

STANDBY CD MODE ADVANCED THEATER DSP DISC 5
DVD/CD TUNER/BAND TV/AUX CD MODE 7 3/8 4.1.
STANDBY indicator CD MODE indicator ADVANCED THEATER indicator DSP indicator Disc tray Disc buttons DISC SKIP EXCHANGE 0 OPEN/CLOSE VOLUME Turn to adjust the volume. PHONES Plug in a pair of headphones here.
DISC indicators CD MODE TV/AUX (/DIGITAL IN) TUNER/BAND DVD/CD STANDBY/ON

Rear Panel