Plantronics Calisto Headset with Bluetooth USB Adapter
For further assistance in using the Plantronics Calisto Headset with Bluetooth USB Adapter with the MacSpeech Dictate family of products, please visit: http://www.macspeech.com/support

Table of Contents

Package Contents... 1 Product Features... 2. Wearing the Headset.... 3 Powering Headset & USB Adapter... 4 Charging the Headset... 5. Headset and USB Adapter Indicators/Alerts.. 6 Pairing Headset with USB Adapter... 7 Pairing Headset with Your Mobile Phone.. 8 Adjusting Computer Audio Settings.. 8 Using the Headset... 9 Using the Headset with MacSpeech Dictate.. 10 Regulatory Notices... 11

Package Contents

USB Adapter

Calisto Headset

USB Headset Charger

Product Features

Reversible Earloop
Call Control Button (on/off) Charge Connection Volume Adjust NoiseCanceling Microphone
Pairing/Connect Button USB Connector

Indicator Light

Wearing the Headset
The headset can be worn on your left or right ear. To switch from one ear to the other, flip the ear loop to the side, and twist around.
The ear tip should fit comfortably in the opening of your ear canal
Point the mouthpiece toward your mouth
Powering Headset & USB Adapter
The headset automatically powers up when it is charging. Powering up: Press and hold Headset button for two seconds. Four ascending beeps will sound when powered on. Powering down: Press and hold Headset button for four seconds. Four descending beeps will sound when powered off. NOTE For your convenience, the headset comes pre-paired with the USB adapter, and (if the headset is within range) will automatically connect to the adapter when powered on.
The USB adapter is automatically powered on upon inserting into the USB port of the computer.

Charging the Headset

Before using, you must first charge your headset. The indicator light glows solid red while charging and turns solid blue when the headset is fully charged. Charge the headset for a minimum of 2 hours. Battery talk time is up to eight hours. NOTE Do not use headset while charging and do not connect the charger while headset is in use.
Headset and USB Adapter Indicators/ Alerts
Headset Indicator Lights Action Turn headset on Turn headset off Turn microphone on/off Adjust volume Button Action Press and hold for two seconds Press and hold for four seconds Press for one second Press up or down (not inward) Sounds four ascending beeps four descending beeps one high beep 2 beeps when max/ min volume reached Indicator Lights Flashes blue every 10 seconds
Headset Alerts Alert Low battery Sounds three beeps every 30 seconds Indicator Lights Flashes red three times every three seconds Glows solid red Glows solid blue while connected to charger

Charging Fully charged

USB Adapter Indicator Lights Action Connected to headset (mic in standby) Microphone on Disconnected from headset Pairing mode Indicator Lights Solid blue Flashes blue Flashes purple Flashes red and blue
Pairing Headset with USB Adapter
NOTE The headset and USB adapter are paired to each other at the factory. However, if you have purchased a USB adapter separately, or if you wish to use a replacement headset with your existing adapter, the units must be paired. Insert the USB adapter in the USB port of your computer.

2 sec.

1.To put the headset into pairing mode, you must first power the headset off. You will hear four descending beeps when the headset powers off. 2.Once headset is off, hold down the call control button for four to six seconds. 3.Release the button when the indicator lights on the headset begin to flash red, then blue. 4.To put the USB adapter into pairing mode, Pinch the pairing/connect 7
button for at least two seconds until the adapter flashes red and blue and begins pairing with your headset. 5.When both the USB adapter and the headset are in pairing mode, and within 30 feet of each other, they should connect. 6.The USB adapter shows a solid blue light when connected to the headset. NOTE Take caution when manually pairing the USB adapter. Do not press hard. Please pinch with both fingers rather than pushing on the adapter to avoid damage to the adapter or the USB port.

Pairing Headset with Your Mobile Phone
1.To put the headset into pairing mode, you must first power the headset off. You will hear four descending beeps when the headset powers off. 2.Refer to your mobile phones user manual for specific instructions about activating Bluetooth pairing. 3. When your mobile phone is searching for Bluetooth devices, press and hold the call control button for 4 to 6 seconds or until the indicator light flashes red and blue. 4.When the mobile phone detects the headset, select Calisto PLT from the list of found devices. 5. When the mobile phone prompts you for a passcode, enter 0000 on the mobile phone keypad.
Adjusting Computer Audio Settings
To use your headset with Mac OS X, ensure that the headset is selected as the default sound input and output device. 1. On your Mac, launch System Preferences (found by clicking on the Apple icon in the upper left corner of your screen). 8
2.Under Sound, click on Input. 3. Select Plantronics BT Adapter. 4. Under Sound, click on Output. 5. Select Plantronics BT Adapter.

Using the Headset

Placing/Answering/Ending calls with your softphone: 1.To make a call, press the call control button on the headset for under one second to activate the microphone and then dial the number via your softphone application. The light on the USB adapter will flash blue while microphone is active. 2.To answer a call, press the headset call control button on the headset for under one second to activate the microphone and then click to answer in your softphone application. 3. To end a call, click to hang up using the controls in your softphone application. NOTE Remember when you are done with a call to put the headset in standby mode (by pressing the call control button for under one second) to conserve battery life. When the headset is in standby mode, the USB adapter will glow solid blue. For other audio applications on computer: 1.Pressing the headset button for under one second will turn the microphone on or off.
Using the Headset with MacSpeech Dictate
When creating a new user profile within MacSpeech Dictate for your headset, note the following: 1. If you have not activated Enable Access for Assistive Devices in Universal Access section of your System Preferences, you will be prompted to do so before you can continue. 2. Next, you will need to create a user profile so that MacSpeech Dictate can get used to your voice, your microphone, and your speech. You will see a blank Profiles Window. 3. To create a profile, click the + button. This will let you enter a profile name and select your microphone type and the language for your profile. 4. Select the Plantronics BT Adapter from the Microphone pull-down menu. 5.Select the spelling model that best suits you from the Spelling pulldown menu, and then choose the Accent. 6. When you have verified your choices are correct, click the Create button. 7. After a short wait, MaSpeech Dictate will create your profile. 8. Be sure that the headset is active and ready for use. The light on the USB Adapter will flash blue when the headset is active. To switch between active and standby, press the headset button for under one second. 9. To conserve battery life, place the headset in standby when not in use. The light on the USB Adapter will remain solid blue to indicate that the headset is in standby.

For further information, and to learn how to use Dictate, see the MacSpeech Dictate User Manual. 10

Regulatory Notices

FCC Requirements Part 15 This device complies with part 15 of the FCC Rules subpart B. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Changes or modifications not expressly approved by the party responsible for compliance could void the users authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.

EXPOSURE TO RF RADIATION

The internal wireless radio operates within the guidelines found in radio frequency safety standards and recommendations, which reflect the consensus of the scientific community. Independent studies have shown that the internal wireless radio is safe for use by consumers. Visit www.plantronics.com for more information.

Industry Canada Notice

This Class B digital apparatus complies with Canadian ICES-003. Cet appareil numrique de la classe B est conforme la norme NMB-003 du Canada. Headset: Model:B70 For IC: 457A-E3XX For FCC ID: AL8-E3XX BlueMax (BUA-100): IC: 457A-BUA100 FCC ID: AL8BUA-100
2009 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Calisto, and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. The Bluetooth word mark is owned by Bluetooth SIG,Inc., and any use of the mark by Plantronics, Inc. is under license 2009 MacSpeech, Inc. and its licensors. All rights reserved. MacSpeech Dictate is a trademark of MacSpeech, Inc.