Savi Go Wireless Headset System WG101/B

User Guide

Welcome
Congratulations on purchasing your new Plantronics product. This user guide contains instructions for setting up and using your Savi Go WG101/B (BUA-200 Adapter + WH100/B Headset) Wireless Headset System. Please refer to the separate safety instructions for important product safety information prior to installation or use of the product.
Plantronics Savi User Guide

Contents

1 Package Contents and Features.. 4
1.1 USB Adapter... 4. 1.2 Headset... 4
4 Using Your Headset System with Microsoft Office Communicator.. 9
Powering Headset On/Off... 9. Placing, Answering and Ending Calls with Microsoft Office Communicator.. 9 Muting a Headset Call.. 10 USB Adapter Indicator Light.. 10. Headset Indicator Lights and Tones.. 10 Out of Range Warning.. 11 Low Battery Warning.. 11 Checking Battery Level.. 11. Turning Headset Indicator Blue Flash On/Off.. 11 Mute Warning... 11 Pairing Headset to USB Adapter.. 11

2 Set Up... 6

2.1 Connecting USB Adapter to PC. 6 2.2 Connecting Power Supply to Charger Base... 6 2.3 Fitting Headset.. 7 2.4 Docking and Charging Headset. 7.

3 Test Call... 8

3.1 Making a Test Call Using Microsoft Office Communicator... 8.
5 Using Your Headset with Your Bluetooth Mobile Phone.. 12
Pairing Your Headset to Your Bluetooth Mobile Phone.. 12. Placing, Answering and Ending Calls with Your Headset and Bluetooth Mobile Phone. 12.
Troubleshooting and Common Questions.. 13.
1 Package Contents and Features
1.1 Savi Go USB Adapter and Charger

Base Power Supply

USB Adapter

Charger Base

USB Charging Cable

1.2 Savi Go Headset

Headband Headset with Pre-Installed Earloop

Foam Ear Cushions

Extra Ear Tab
Savi Go USB Adapter Features

Pairing Button

Indicator Light

Savi Go Headset Features

Earloop Ear Tab
Call Control Button (also controls volume and mute functions)

Microphone

2 Set Up
2.1 Connecting USB Adapter to PC
1 Insert the USB adapter into USB Port on PC. The indicator
light on the base will be solid red to indicate the USB adapter is powered on.
2.2 Connecting Power Supply to Charger Base
1 Connect the base power supply into the power jack on

the charger base.

2 Connect the power supply to the outlet. The power
indicator light will be solid green.
Important NOTE For best performance it is recommended that Windows is updated with Service Pack levels listed below: Microsoft Windows XP-Service Pack 3 (SP3) or later Microsoft Windows Vista-Service Pack 1 (SP1) or later

2.3 Fitting Headset

The headset comes with a pre-installed earloop and ear tab. An optional headband is also provided.
5The ear tab has been designed to maximize stability of
the headset. It can be rotated on the headset to optimize its fit and comfort in the ear. If desired, the ear tab can be removed by pulling tab from the headset.

1To install the headband, gently unsnap the pre-installed
earloop from the headset.
2 Snap the headband into the headset. The headband can

be adjusted to fit.

3 For either wearing option rotate the headset until the
microphone is pointed toward your mouth.
4The headset can be converted for wearing on the left or
right ear with both earloop and headband.
2.4 Docking and Charging Headset
Ear Tab Earloop Headset Snap Headband
1 Gently push the headset into the charge cradle.
The indicator light on the headset will be solid red to indicate that the headset battery is charging
2 Charge for at least 20 minutes prior to the first use.
A full charge takes 3 hours.

Charging time 20 min..

Minimum charge before first use

3 hours..

Full charge

Power Indicator Light

Note The USB charging cable can also be used to charge the headset. To successfully charge your headset with the USB cable the PC must be on and in active state (not standby). The charging time will vary according to the number of other devices drawing power from the PCs USB port(s).

3 Test Call

3.1 Making a Test Call Using Microsoft Office Communicator
1 Ensure Microsoft Office Communicator is running on

your PC.

2 Set the headset and microphone volume to a
comfortable level using the Microsoft Office Communicator Set up Audio and Video page.*
3 Place a test call using Microsoft Office Communicator. 4 Adjust the receive and listen volume to comfortable
levels using the volume control in the Conversation Window.*
5 You can also fine tune the listening volume on the
headset by pushing the call control button up to increase the volume and pushing down to decrease the volume.
NOTE Do not press the call control button in when adjusting the volume otherwise the call can be ended accidentally.
6.To end the test call, press the call control button on the
headset. For your safety, do not use headset at high volumes for extended periods of time. Doing so can cause hearing loss. Always listen at moderate levels. For more information on headsets and hearing visit: www. plantronics.com/healthandsafety.

* Consult Microsoft Office Communicator Help for more information.
4 Using Your Headset System with Microsoft Office Communicator

Powering Headset On/Off

The headset will be ready to use once it has been charged in the charger base as described in Section 2.4 Docking and Charging the Headset. To conserve power you may optionally power the headset off, by pressing and holding the call control button for six seconds. The headset indicator light will be lit red for four seconds to confirm that the headset is powered off. Note once powered off you will not be able to use the headset. To power the headset back on press and hold the call control button for four seconds when the headset indicator will light blue for two seconds, then flash red a number of times to indicate the remaining battery charge (see Checking the Battery Level). Indicator Light

Call Control Button

Placing, Answering, and Ending Calls with Microsoft Office Communicator
To place a call To answer a call on the headset To answer a call when already on an active call on your mobile phone To end a call on the headset Dial number using Microsoft Office Communicator* Short press call control button on headset Short press the call control button once to end the mobile phone call then press again to answer your Microsoft Office Communicator call Short press call control button on headset
*Consult Microsoft Office Communicator Help for more information on how to place a call. Note You can also answer calls directly from Microsoft Office Communicator by clicking on the Call Alert that appears on your PC screen. In this case the call will be directed to the default speakerphone which may not be your headset. Consult Microsoft Office Communicator Help for more information.

Muting a Headset Call

To mute a call, press and hold the call control button down (in the volume down position) for two seconds. You will hear a low/high tone pair indicating the mute is activated. To unmute a call, push and hold the call control button down (in the volume down position) for two seconds. You will hear a high/ low tone pair indicating the mute is deactivated. Volume Down Button

USB Adapter Indicator Light
USB Adapter Status Headset in talk mode Base and headset pairing Indicator Light Flashes blue Flashes red and blue
Headset Indicator Lights and Tones
Headset Status Headset charging Headset fully charged Headset battery low Headset ready Incoming call Active call Headset Indicator Light Solid red Off Flashes double red Slow blue flash (every 10 sec.) Flashes purple Flashes blue

Out of Range Warning

If you are on a call you will hear the audio degrade as you move out of range. If you stay out of range, active calls will be suspended. Calls will be re-established upon walking back into range.
Pairing Headset to USB Adapter
The headset and USB adapter are supplied paired to each other. However, if you wish to use a replacement headset with your existing USB adapter, the units can be paired to each other by the following method:
1 Ensure your replacement headset is fully charged.

Low Battery Warning

A repeating high/low tone pair every 10 seconds indicates the battery is low. You should recharge the headset immediately.
2 Power the headset off by pressing and holding the call
control button for six seconds. The headset indicator light will be red for four seconds.
3 Place the headset in pairing mode by pressing and
holding the call control button until the indicator light flashes red and blue.

Checking Battery Level

You can check the battery level by moving the call control button to the volume down position, then pressing inwards and holding for two seconds. The headset indicator will flash red to indicate the remaining battery charge level. One red flash = low charge level Two red flashes = medium charge level Three red flashes = high charge level
4 Place the USB adapter in pairing mode by pressing
and holding the pairing button on the adapter for two seconds. The pairing light will flash red and blue.
5 When the pairing light on the USB adapter goes solid
blue, the headset and the USB adapter are paired.
Turning Headset Indicator Blue Flash On/Off
By default the headset indicator flashes blue to indicate the headset state as described in the section Headset Indicator Lights and Tones. This feature may be disabled by moving the call control button to the volume up position, then pressing inwards and holding for two seconds. The headset indicator will show a short burst of blue flashes. Repeat this operation to turn the headset blue flashing indicator back on.
NOTE Take caution pairing the USB adapter. Do not press hard. Please press with both fingers rather than push on the USB adapter to avoid damage to the USB adapter or USB port.

Mute Warning

When mute is activated, you will hear a single low tone which will repeat every 30 seconds.
5 Using Your Headset with your Bluetooth Mobile Phone
Pairing your Headset to your Bluetooth Mobile Phone
1Turn on your mobile phone and enable Bluetooth. For
most phones select Settings>Tools>Connections> Bluetooth>On. See your phones user guide for more information.
4 Use the commands on your phone to locate the headset.
For most phones select Settings>Tools>Connections> Bluetooth>Search>Savi Go WH100. See your phones user guide for more information.
5 When prompted for a passkey, enter 0000 (4 zeros). The
headset indicator light will flash blue when paired successfully. Note For detailed pairing instructions for popular mobile phones visit: www.plantronics.com/easytopair.
3 Press and hold the headset call control button for six
seconds or until the red and blue indicator lights flash alternately. Note The headset will stay in pairing mode for three minutes.
Placing, Answering, and Ending Calls with your Headset and Bluetooth Mobile Phone
To place a call To answer a call To answer a call when already on an active Microsoft Office Communicator call To end a call Redial last number* Dial number on your mobile phone keypad Short press call control button. Short press the call control button to end the Microsoft Office Communicator call, then press again to answer your mobile phone call Short press call control button. Double tap call control button. There will be a high tone on each press. A final tone indicates the last number has been redialed. Press and hold call control button for two seconds. First tone on key press start followed by a second tone which indicates voice dial is activated. Press and hold call control button until you hear two tones. Press and hold call control button for two seconds until you hear a long tone.

Activate voice dialing*

Reject a call Transfer a call from your mobile phone to your headset Transfer a call from your headset to your mobile phone
Press and hold call control button for two seconds until you hear a long tone.
* Only available on mobile phones and carriers that support these features.
Troubleshooting and Common Questions
Troubleshooting Microsoft Office Communicator Usage
My headset doesnt work with Microsoft Office Communicator.
Make sure your headset is charged. Make sure your headset is on and connected. Press the call control button on your headset. Fine tune the listening volume with the call control button. If the volume is still too low, adjust the listening volume on the PC using Microsoft Office Communicator*.
The sound is distorted or I hear an echo in the headset.
Reduce speaking volume on the PC using Microsoft Office Communicator*. Point microphone towards your chin. If the distortion is still present, lower the volume using the call control button.

While on an Microsoft Office Communicator call I want to accept a call from my mobile phone. Reconnecting the Bluetooth link between your headset and USB adapter. Talk time performance is significantly degraded even after a full recharge.
Press the call control button for less than 1 second (this will disconnect the Microsoft Office Communicator call.) Press the call control button again to connect with your mobile phone.
If you turn on the headset beyond Bluetooth range, and then return within it, you may need to reestablish the Bluetooth link by pressing the USB adapter button.
Battery is wearing out. Contact www.plantronics.com/support for factory service information.
* Consult Microsoft Office Communicator Help for more information
Troubleshooting Mobile Phone Usage
My headset does not work with my phone. Make sure the headset is fully charged. Make sure headset is paired with the Bluetooth phone you are trying to use. See Pairing Your Headset to your Bluetooth Mobile Phone on page 12.
My phone did not locate the headset.
Turn both your phone and headset off and on, and then repeat the pairing process on page 12.
I could not enter my PIN code.
Turn both your phone and headset off and on, and then repeat the pairing process on page 12. Your PIN code, or Passkey, is 0000.
I cannot hear caller/dial tone.
The headset is not turned on. Press the call control button for approximately 4 seconds until you hear a tone or see the indicator glow blue. Your headset is out of range. Move the headset closer to the Bluetooth phone. Your headset battery is drained. Charge your battery. See Docking and Charging Headset on page 7. The listening volume is too low. Incremental tapping of the call control button will adjust volume. Make sure that the headset fits properly. See Fitting Headset on page 7.

Audio quality is poor.

Your headset is out of range. Move the headset closer to the Bluetooth phone.

Callers cannot hear me.

Make sure that headset is sitting correctly in ear with boom pointing towards corner of mouth. See Fitting Headset on page 7.
My headset falls off my ear.
Make sure that Headset is sitting correctly on your ear with boom pointing towards corner of mouth. See Fitting Headset on page 7.
Plantronics, Inc. 345 Encinal Street Santa Cruz, CA 95060 United States www.plantronics.com For product support contact us at www.plantronics.com/support.
2009 Plantronics, Inc. All rights reserved. Plantronics, the logo design, Savi, and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. Microsoft, Windows and Vista are trademarks or registered trademarks of Microsoft Corporation. The Bluetooth word mark is owned by Bluetooth SIG, Inc. and any use of the mark by Plantronics is under license. Patents US 5,210,791; Patents Pending. XXXXX-XX (01.09)

Savi Go Wireless headset system WG101/B

User Guide

Welcome
Congratulations on purchasing your new Plantronics product. This user guide contains instructions for setting up and using your Savi Go WG101/B (BUA-200 USB adapter + WH100/B headset) wireless headset system. Please refer to the separate safety instructions for important product safety information prior to installation or use of the product.
Plantronics Savi User Guide

Contents

1 Package contents and features.. 4.
1.1 USB adapter... 4 1.2 Headset... 4
5 Using your headset with your Bluetooth mobile phone... 11
Pairing your headset to your Bluetooth mobile phone... 11 Placing, answering and ending calls with your headset and Bluetooth mobile phone. 11.

2 Set-up... 6.

2.1 Connecting USB adapter to PC. 6 2.2 Connecting power supply to charger base.. 6 2.3 Fitting headset... 7 2.4 Docking and charging headset.. 7
6 PerSono Suite software.. 12
Softphone support.. 12. Battery life.. 12. Settings screen headset and USB adapter.. 13 Help for USB adapter settings. 13. PC panel screen... 14 Advanced settings... 14 Support screen... 14 Updates.. 14
3 Using your headset system with Microsoft Office Communicator.. 8
Powering headset on/off.. 8. Placing, answering and ending calls with Microsoft Office Communicator.. 8
4 System information... 9
Muting a headset call... 9. USB adapter indicator light.. 9 Headset indicator lights and tones.. 9 Out of range warning.. 10 Low battery warning... 10 Checking battery level.. 10 Turning headset indicator blue flash on/off. 10 Mute warning... 10 Pairing headset to USB adapter.. 10
7 Troubleshooting and common questions. 15
1 Package contents and features
1.1 Savi Go USB adapter, charger and CD
USB adapter Base power supply

Charger base

CD includes: PerSono Suite Software Complete User Guide

USB charging cable

1.2 Savi Go WH100/B headset
Headset with pre-installed ear loop

Headband

Foam ear cushions

Extra ear tab

Savi Go USB adapter features

Pairing button

Indicator light
Savi Go WH100/B headset features

Ear loop Ear tab

Call control button (also controls power, volume and mute functions)

Microphone

2 Set-up
2.1 Connecting USB adapter to PC
1 Insert the USB adapter into the USB port on the PC. The
indicator light on the adapter will be solid red to indicate the USB adapter is powered on.
2.2 Connecting power supply to charger base
1 Connect the base power supply into the power jack on

the charger base.

2 Connect the power supply to the outlet. The power
indicator light will be solid green.
Important NOTE For best performance, it is recommended that Windows is updated with Service Pack levels listed below: Microsoft Windows XP - Service Pack 3 (SP3) or later Microsoft Windows Vista - Service Pack 1 (SP1) or later

2.3 Fitting headset

The headset comes with a pre-installed ear loop and ear tab. An optional headband is also provided.

6 The ear tab has been designed to maximise stability of
the headset. It can be rotated on the headset to optimise its fit and comfort in the ear. If desired, the ear tab can be removed by pulling the tab from the headset.
1 To install the headband, rotate the pre-installed ear loop
so the ear loop and headset are aligned with one another as shown. Gently unsnap the ear loop from the headset. NOTE The headset or ear loop can be damaged if they are not aligned with one another before removing.
2 Hold the headband so it is aligned to receive the headset
as shown and snap the headband into the headset.
3 Adjust the headband to fit. 4 For either wearing option, rotate the headset until the
microphone is pointed towards your mouth.
5The headset can be converted for wearing on the left or
right ear with both ear loop and headband. Ear tab Headset Ear loop Headband
2.4 Docking and charging headset
1 Gently push the headset into the charging cradle.
The indicator light on the headset will be solid red to indicate that the headset battery is charging.
2 Charge for at least 20 minutes prior to the first use.
A full charge takes 3 hours.

Charging time 20 min..

Minimum charge before first use

3 hours..

ull charge F

Power indicator light

Note The USB charging cable can also be used to charge the headset. To successfully charge your headset with the USB cable, the PC must be on and in an active state (not standby). The charging time will vary according to the number of other devices drawing power from the PCs USB port(s).
3 Using your headset system with Microsoft Office Communicator

Powering headset on/off

The headset will be ready to use once it has been charged in the charger base as described in Section 2.4 Docking and charging the headset. To power the headset on, press the call control button in for four seconds. The indicator light will remain solid blue for two seconds to confirm that the headset is powered on. Note The USB adapter indicator light will remain solid blue when the headset is powered on and paired to the headset. The indicator light will remain solid red when the headset is powered on but not paired to the headset. To conserve power, you may optionally power the headset off by pressing the call control button in for six seconds. The headset indicator light will remain solid red for four seconds to confirm that the headset is powered off. Note Once powered off you will not be able to use the headset.

Call control button

Placing, answering and ending calls with Microsoft Office Communicator
To place a call To answer a call on the headset To answer a call when already on an active call on your mobile phone To end a call on the headset Short press call control button on headset. Dial number using Microsoft Office Communicator* Short press call control button on headset. Short press the call control button once to end the mobile phone call, then press again to answer your Microsoft Office Communicator call. Short press call control button on headset.

*Consult Microsoft Office Communicator Help for more information on how to place a call.
Note You can also answer calls directly from Microsoft Office Communicator by clicking on the Call Alert that appears on your PC screen. In this case the call will be directed to the default speakerphone which may not be your headset. Consult Microsoft Office Communicator Help for more information.
For your safety, do not use headset at high volumes for extended periods of time. Doing so can cause hearing loss. Always listen at moderate levels. For more information on headsets and hearing, visit: www.plantronics.com/healthandsafety.

4 System information

Muting a headset during a call
To mute a call, press and hold the call control button down (in the volume down position) for two seconds. You will hear a low-high tone pair indicating the mute is activated. To unmute a call, push and hold the call control button down (in the volume down position) for two seconds. You will hear a highlow tone pair indicating the mute is deactivated. Volume down button
USB adapter indicator light
USB adapter status Headset in talk mode Adapter and headset pairing Connected, no activity Powered on - headset not paired Indicator light Flashes blue Flashes red and blue Solid blue Solid red
Headset indicator lights and tones
Headset status Headset charging Headset fully charged Headset battery low Headset ready Incoming call Active call Headset indicator light Solid red Off Flashes double red Slow blue flash (every 10 sec.) Flashes purple Flashes blue

Out of range warning

If you are on a call, you will hear the audio degrade as you move out of range. If you stay out of range, active calls will be suspended. Calls will be re-established when you walk back into range.
Pairing headset to USB adapter
The headset and USB adapter are supplied paired to each other. However, if you wish to use a replacement headset with your existing USB adapter, the units can be paired to each other by the following method:
1 Ensure your replacement headset is fully charged.

Low battery warning

A repeating high/low tone pair every 10 seconds indicates the battery is low. You should recharge the headset immediately.

2 Power the headset off by pressing and holding the call
control button for six seconds. The headset indicator light will be red for four seconds.
3 Place the headset in pairing mode by pressing and
holding the call control button until the indicator light flashes red and blue.

Checking battery level

You can check the battery level by moving the call control button to the volume down position, then pressing inwards and holding for two seconds. The headset indicator will flash red to indicate the remaining battery charge level. One red flash = low charge level Two red flashes = medium charge level Three red flashes = high charge level
4 Place the USB adapter in pairing mode by pressing
and holding the pairing button on the adapter for two seconds. The pairing light will flash red and blue.
5 When the pairing light on the USB adapter goes solid
blue, the headset and the USB adapter are paired.
Turning headset indicator blue flash on/off
By default, the headset indicator flashes blue to indicate the headset state as described in the section Headset indicator lights and tones. This feature may be disabled by moving the call control button to the volume up position, then pressing inwards and holding for two seconds. The headset indicator will show a short burst of blue flashes. Repeat this operation to turn the headset blue flashing indicator back on.
NOTE: Take care when pairing the USB adapter. Do not press hard. Please press with both fingers rather than push on the USB adapter to avoid damage to the USB adapter or USB port.

Mute warning

When mute is activated, you will hear a single low tone which will repeat every 30 seconds.
5 Using your headset with your Bluetooth mobile phone
Pairing your headset to your Bluetooth mobile phone
1Turn on your mobile phone and enable Bluetooth. For
most phones, select Settings>Tools>Connections> Bluetooth>On. See your phones user guide for more information.
Note The headset will stay in pairing mode for three minutes.
4 Use the commands on your phone to locate the headset.
For most phones select Settings>Tools>Connections> Bluetooth>Search>Savi Go WH100. See your phones user guide for more information.

5 When prompted for a password, enter 0000 (4 zeros).
The headset indicator light will flash blue when paired successfully. Note For detailed pairing instructions for popular mobile phones, visit: www.plantronics.com/easytopair.
2 If the headset is powered on, power the headset off by
pressing the call control button in for six seconds. The headset indicator light will remain solid red for four seconds to indicate that the headset is powered off.
3 Press the headset call control button in for six seconds
or until the indicator light flashes red and blue alternately.
Placing, answering and ending calls with your headset and Bluetooth mobile phone
To place a call To answer a call To answer a call when already on an active Microsoft Office Communicator call To end a call Redial last number* Dial number on your mobile phone keypad. Short press call control button. Short press the call control button to end the Microsoft Office Communicator call, then press again to answer your mobile phone call. Short press call control button. Double tap call control button. There will be a high tone on each press. A final tone indicates the last number has been redialed. Press and hold call control button for two seconds. First tone on key press start, followed by a second tone which indicates voice dial is activated. Press and hold call control button until you hear two tones. Tap any button to clear the indicator light. The indicator light will triple flash purple every 10 seconds for 5 minutes or until cleared. Press and hold call control button for two seconds until you hear a long tone.

Activate voice dialling*

Reject a call Missed call
Transfer a call from your mobile phone to your headset Transfer a call from your headset to your mobile phone
Press and hold call control button for two seconds until you hear a long tone.
* Only available on mobile phones and carriers that support these features.

6 PerSono Suite software

It is highly recommended that you install the PerSono Suite software. Though your Savi Go system will operate without the software running, it will limit the systems capabilities. PerSono Suite software allows you to do the following with your Savi Go system: Answer/end calls from the PC remotely with the headset (requires use of supported softphone) Customise your headset and adapter settings to your personal preferences Automatically manage your PC multimedia so you never miss a call Quickly access links to product support and software/firmware upgrade information
3 The Manage API Access Control screen will pop
up stating that Another program is trying to access Skype. The name of the program will appear as PerSonoSuite.exe with the publisher Plantronics, Inc. You must select Allow this program to use Skype and click OK.

Softphone support

For a list of softphones supported by PerSono Suite, refer to www.plantronics.com/SoftphoneCompatibility PerSono Suite software supports all the softphones on the list with no additional steps by the user except Skype. To allow Skype to be a supported softphone in PerSono Suite, please follow these steps:
4 To confirm that PerSono Suite is now supporting Skype,
go to the PC Panel tab in PerSono Suite and ensure that Skype is listed under Softphones.
1 Ensure PerSono Suite software is running on your PC.
You will see a headset icon in the lower right-hand portion of the PC tray bar when PerSono Suite software is running.
2 If Skype is running on your PC, Skype will notify you of
the event that PerSonoSuite.exe wants to use Skype. Go to the new event tab located in the upper right of the Skype window and click on the red flag. You then will need to click on the PerSonoSuite.exe link to be taken to the Manage API Access Control screen.

Battery life

PerSono Suite.exe
At the lower left-hand corner of the screen (and for all software screens), you will see one of the following icons indicating the approximate charge left in the headset battery.

Less than 5 mins

Settings screen headset and USB adapter
The Settings screen allows you to customise the adapter and headset to your preference. The Savi Go system is supplied with the default settings and can be changed as described in the Settings column below. NOTE Some parameters may appear as greyed out. PerSono Suite automatically greys out parameters that do not apply to a particular Plantronics device.

Settings headset

Feature Mute tone Ring tone PC Ring tone volume PC Ring tone - mobile Ring tone volume - mobile Second inbound call Settings On/off Sound 1/sound 2/sound 3 On/off Sound 1/sound 2/sound 3 On/off Ring continuously/ring once/ignore Default On Sound 2 On Sound 1 On Ring continuously

Settings USB adapter

Feature Audio bandwidth PC Ring both headset/PC Settings Wideband/narrowband On/Off Default Wideband On
Help for USB adapter settings
Audio Bandwidth The system will support both narrowband and wideband audio from the PC. Wideband audio delivers heightened speech clarity and life-like fidelity. However, wideband audio consumes more battery power and has more stringent access criteria, which reduces the number of systems that can be deployed in a small area. All PCs support wideband audio. When switching between narrowband and wideband audio, you must re-establish the audio link for the changes to take effect. Wideband PC

PC panel screen

Choose whether you want PerSono Suite software to launch when you log in to Windows. See a list of supported softphones running on your PC. See which Plantronics device is attached to your PC and working with PerSono Suite software. Customise how you want the PerSono Suite software to manage your multimedia when a call begins/ends.

Support screen

The support screen provides on-line access to this printable User Guide, frequently asked questions, details on how to contact Plantronics, and software upgrade information. The version of software and firmware currently running on your system is also shown here.

Updates

All the required software and firmware for your Plantronics device can be remotely updated if and when updates are available. You can control how frequently the system will check for available updates. When updates are available, you can view all pending updates and decide when to download and install any one of them. The particular version of PerSono Suite software and headset/ base firmware running on your system is always reflected in the VERSIONS fields.
Notify me when updates are available: By enabling this check box,

Advanced settings

Microsoft Office Communicator dial tone enabled
If this feature is set to ON, when a PC radio link is established, Microsoft Office Communicator will assume the user is trying to place a VOIP call and provide a dial tone. If this feature is set to OFF, when a PC radio link is established, Microsoft Office Communicator will sit idle. Microsoft Office Communicator dial tone enabled can be set to ON or OFF. Microsoft Office Communicator certified product: Default setting = ON Standard product: Default setting = OFF

Audio sensing enabled

you will activate a periodic automatic check for available software and firmware updates. When this parameter is enabled, automatic check for updates will be activated and the frequency field will be highlighted allowing you to choose the frequency of checking for updates, e.g., once every 3 months, once every month or once every week. When this parameter is disabled, automatic check for software/ firmware updates is disabled.
Check For Updates: You can choose to check for available
Audio sensing is a special feature supported by Plantronics wireless devices that can detect audio signal at the USB port and automatically establish a PC radio link between the base and wireless headset without the user having to press the PC call control button. If the parameter Microsoft Office Communicator dial tone enabled is set to ON, every time the user presses the PC call control button, the Microsoft Office Communicator dial tone will be heard. However, the user may have pressed the PC call control button to listen to music etc., and does not want to hear the dial tone. In this case, if the user sets the Audio sensing enabled parameter to ON, the radio link will be established automatically when any PC audio is detected at the USB port, thus eliminating the need for the user to press the PC call control button. Audio sensing enabled can be set to ON or OFF. Microsoft Office Communicator certified product: Default setting = ON Standard product: Default setting = OFF

software/firmware updates at any time by clicking on the Check For Updates button.
Available Updates: Following an automatic or manual check for
updates, this field will be populated with any applicable software and firmware updates.
Install: It is important to note that automatic checks for updates
does not include automatic download and install. The actual download and install will only occur when you select at least one item for the Available Updates list and click on this Install button.
7 Troubleshooting and common questions
Troubleshooting Microsoft Office Communicator usage
My headset doesnt work with Microsoft Office Communicator.
Make sure your headset is charged. Make sure your headset is on and connected. Press the call control button on your headset. Fine-tune the listening volume with the call control button. If the volume is still too low, adjust the listening volume on the PC using Microsoft Office Communicator*.
The sound is distorted or I hear an echo in the headset.
Reduce speaking volume on the PC using Microsoft Office Communicator*. Point microphone towards your chin. If the distortion is still present, lower the volume using the call control button.
While on a Microsoft Office Communicator call, I want to accept a call from my mobile phone. Reconnecting the Bluetooth link between your headset and USB adapter. Talk time performance is significantly degraded even after a full recharge.
Press the call control button for less than 1 second (this will disconnect the Microsoft Office Communicator call.) Press the call control button again to connect to your mobile phone.
If you turn on the headset beyond Bluetooth range and then return within it, you may need to reestablish the Bluetooth link by pressing the USB adapter button.
Battery is wearing out. Contact www.plantronics.com/support for factory service information.
* Consult Microsoft Office Communicator Help for more information
Troubleshooting Mobile phone usage
My headset does not work with my phone. Ensure that the headset is fully charged. Make sure the headset is paired with the Bluetooth phone you are trying to use. See Pairing your headset to your Bluetooth mobile phone on page 11.
My phone did not locate the headset.
Turn both your phone and headset off and on and then repeat the pairing process on page 11.
I could not enter my PIN code.
Turn both your phone and headset off and on and then repeat the pairing process on page 11. Your PIN code, or password, is 0000.
I cannot hear caller/dial tone.
The headset is not turned on. Press the call control button for approximately 4 seconds until you hear a tone or see the indicator glow blue. Your headset is out of range. Move the headset closer to the Bluetooth phone. Your headset battery is drained. Charge your battery. See Docking and charging headset on page 7. The listening volume is too low. Incremental tapping of the call control button will adjust volume. Make sure that the headset fits properly. See Fitting headset on page 7.

Audio quality is poor.

Your headset is out of range. Move the headset closer to the Bluetooth phone.

Callers cannot hear me.

Make sure that the headset is sitting correctly on your ear with the boom pointing towards the corner of the mouth. See Fitting headset on page 7.
My headset falls off my ear.
Plantronics, Inc. 345 Encinal Street Santa Cruz, CA 95060 United States www.plantronics.com For product support, contact us at www.plantronics.com/support.
2009 Plantronics, Inc. All rights reserved. Plantronics, the logo design, PerSono, Savi and Sound Innovation are trademarks or registered trademarks of Plantronics, Inc. Microsoft, Windows and Vista are trademarks or registered trademarks of Microsoft Corporation. Skype is a trademark of Skype Limited or other related Skype companies. The Bluetooth word mark is owned by Bluetooth SIG, Inc. and any use of the mark by Plantronics is under licence. Patents US 5,210,791; Patents Pending. 81668-02 (09.09)