OPTION #1 Rcepteurs dots de la fonction Sub Outla mthode de raccord la plus courante pour rcepteurs Dolby Digital. Note: Utilisez sa place une des entres de ligne-gauche ou droite (vous pouvez aussi utiliser un adaptateur en Y pour jumeler les entres de ligne gauche et droite). Aprs avoir effectu le raccord Sub Out du rcepteur lentre de ligne du subwoofer, tournez compltement le contrle Low Pass vers la droite. Raccordez toutes les enceintes directement au rcepteur. Pour loption #1, rglez les contrles de haut-parleurs de votre rcepteur comme suit: Small (petit) pour les haut-parleurs Front (avant), Center (centre) et Surround (ambiophoniques). Rglage du rcepteur: Small (petit) pour les haut-parleurs Front (avant), Center (centre) et Surround (ambiophoniques). Rglez le contrle du subwoofer ON, YES, ou PRESENT. Rglez le contrle de la frquence de sparation du rcepteur 120Hz. Consultez le manuel dutilisation de votre rcepteur pour tablir la configuration de vos enceintes.
5.1 SYSTEM OPTION 2 HOOKUP
Hookup Option 2 Note: Diagram shows wiring only, not speaker position. Opo de conexo 2 Nota: O diagrama mostra apenas a fiao e no ilustra a posio das caixas acsticas. Opzione collegamento 2 Nota: Schema mostra solo il cablaggio, non lubicazione dei diffusori. Anschlussoption 2 Hinweis: Das Diagramm zeigt nur die Verkabelung, nicht die Lautsprecherposition. Opcin de cableado 2 Nota: En el diagrama se muestra slo el cableado, no la ubicacin de los altavoces. Option de branchement 2 Note: Le diagramme indique le cblage seulement, non la position des enceintes.

6.1 SYSTEM - OPTION 2

7.1 SYSTEM - OPTION 2
OPTION #2 Two channel or Dolby Pro Logic receiver with no Sub Out. If you elect to use the speaker level inputs, use two-conductor 16 gauge or thicker speaker wires. See your Polk dealer for wire recommendations. Note that one of the speaker input terminals on the rear of the speaker is marked red (+) and the other black (-). Make certain that you connect the wire from the red (+) terminal of your receiver to the red (+) terminal on your speaker, and the wire from the black (-) terminal of the receiver to the black (-) terminal on your speaker. Speaker wire has some indication (such as color coding, ribbing, or writing) on one of the two conductors to help maintain consistency. If your subwoofer doesn't seem to produce much bass, it is most likely that one of the speaker wires is connected backwards. Double check all connections for correct polarity. Strip 1/2" (12mm) of insulation from each of the two conductors on both ends to expose the bare wire. Twist the exposed wire of each conductor to form two un-frayed strands. Connect the left and right front speaker outputs of your receiver to the speaker level inputs of the powered subwoofer using speaker wire. Then, connect the left and right front speakers using speaker wire from the speaker level outputs from the powered subwoofer. Connect the Center Channel Speaker directly to the center channel output from your receiver. Connect the Rear Surround Satellites directly to the rear or surround channel outputs from your receiver. Receiver Settings: Front speakers = LARGE Subwoofer = OFF or NO Center and Surrounds= SMALL Crossover Frequency= 120 Hz

ADJUSTING YOUR SYSTEM

SUBWOOFER ADJUSTMENTS Your Powered Subwoofer offers a range of setting options. We recommend the following settings as starting points, but the settings that are best for you depend upon your speaker placement, electronics and personal taste. After you've become familiar with what the settings do, experiment with alternate options to find the method that works best for your system setup. You'll find an informative article on Subwoofer Positioning and Adjustment in the set up section at: www.polkaudio.com/education/article.php?id=19. Note: When you set up your subwoofer for the first time, you will probably have to make adjustments several times before you hear what you personally like. Start with the volume at 50%. AC POWER CONNECTION AND AUTO ON/OFF Your subwoofer features auto on/off circuitry, marked auto on the power switch, which automatically turns your subwoofer on when it senses a program signal. We recommend the auto setting if your subwoofer is always receiving power (ie, if it's plugged into a wall outlet). When no signal is present, the circuit turns the subwoofer off after 15 minutes. If you are concerned about the brief delay between when the music starts and when the subwoofer turns on, simply leave your subwoofer in the On position. You may want to leave your system unplugged during extended periods of non use, such as during a vacation. FINE TUNING YOUR SUBWOOFER VolumeAdjust by ear using a wide variety of CDs and video sources. Adjust for deep, powerful bass without boominess. Low PassNOTE: This control should be turned all the way up when the subwoofer is connected with Method #1 (LINE IN). This control adjusts the frequency range over which the subwoofer operates. If male vocals sound thin, turn this control up until the voice sounds rich but not boomy. If male vocals sound too thick or chesty, turn this control down until the voice sounds natural. Phase SwitchSit in your favorite listening position. Play music (not a movie) with a walking bass line. We recommend playing jazz or country music. Now listen carefully for the point at which the subwoofer transitions to your main speakers. This is the crossover point, and this point should be below the frequency of a male human voice. Whichever phase setting sounds louder or fuller at the subwoofers crossover (transition) point is the optimum setting. Sometimes no difference will be heard. TROUBLESHOOTING No sound coming from subwoofer If hookup is Sub Out to LINE IN, is your receiver set to Subwooferyes If hookup is via speaker wire, check that the polarity of the wires is correct. If hookup is Sub Out to LINE IN, is your receiver set to Subwooferyes If hookup is via speaker wire, check that the polarity of the wires is correct. Check outlet; check fuse after unplugging the subwoofer and calling customer service.

TECHNICAL ASSISTANCE If after following the hook-up directions, you experience difficulty, please double check all wire connections. Should you isolate the problem to the speaker, contact the authorized Polk Audio dealer where you made your purchase or call Polk Audios Customer Service Department at 1-800-377-7655 (calls from US or Canada only) from 9am to 6pm, Eastern Time, Monday through Friday. You may also contact us via email polkcs@polkaudio.com. ASSISTANCE TECHNIQUE OU SERVICE Si aprs avoir suivi le mode de connexion vous prouvez des difficults, vrifier toutes vos connexions. Si le problme semble provenir du haut-parleur, contactez le revendeur Polk agr de qui vous avez achet le produit ou communiquez avec le Service la Clientle de Polk Audio au 1-800-377-7655 (appels du Canada et des.U. seulement) du lundi au vendredi, 9h00 - 18h00 HNE. Vous pouvez galement communiquer avec nous par courriel: polkcs@polkaudio.com.

LIMITED WARRANTY

Polk Audio, Inc., warrants to the original retail purchaser only. This warranty will terminate automatically prior to its stated expiration if the original retail purchaser sells or transfers the Product to any other party. Polk Audio, Inc., warrants, to the original retail purchaser only, that the LOUDSPEAKER(S), PASSIVE CROSSOVER COMPONENT(S) and ENCLOSURE on this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of five (5) years from the date of original retail purchase rom a Polk Audio Authorized Dealer. Furthermore, Polk Audio, Inc., warrants, to the original retail purchaser only, that any AMPLIFIER OR OTHER ELECTRONIC COMPONENT that may be included in this Polk Audio Loudspeaker Product will be free from defects in material and workmanship for a period of three (3) years years from the date of original retail purchase from a Polk Audio Authorized Dealer. To allow Polk Audio to offer the best possible warranty service, please register your new product online at: www.polkaudio.com/registration or call Polk customer service 800-377-7655 in the USA and Canada (outside the USA: 410-358-3600) within ten (10) days of the date of original purchase. Be sure to keep your original purchase receipt. Defective Products must be shipped, together with proof of purchase, prepaid insured to the Polk Audio Authorized Dealer from whom you purchased the Product, or to the Factory at 2550 Britannia Boulevard, Suite A, San Diego, California 92154. Products must be shipped in the original shipping container or its equivalent; in any case the risk of loss or damage in transit is to be borne by you. If upon examination at the Factory or Polk Audio Authorized Dealer it is determined that the unit was defective in materials or workmanship at any time during this Warranty period, Polk Audio or the Polk Audio Authorized Dealer will, at its option, repair or replace this Product at no additional charge, except as set forth below. All replaced parts and Products become the property of Polk Audio. Products replaced or repaired under this warranty will be returned to you, within a reasonable time, freight prepaid. This warranty does not include service or parts to repair damage caused by accident, disaster, misuse, abuse, negligence, inadequate packing or shipping procedures, commercial use, voltage inputs in excess of the rated maximum of the unit, cosmetic appearance of cabinetry not directly attributable to defect in materials or workmanship, or service, repair, or modification of the Product which has not been authorized or approved by Polk Audio. This warranty shall terminate if the Serial number on the Product has been removed, tampered with or defaced. This warranty is in lieu of all other expressed Warranties. If this Product is defective in materials or workmanship as warranted above, your sole remedy shall be repair or replacement as provided above. In no event will Polk Audio, Inc. be liable to you for any incidental or consequential damages arising out of the use or inability to use the Product, even if Polk Audio, Inc. or a Polk Audio Authorized Dealer has been advised of the possibility of such damages, or for any claim by any other party. Some states do not allow the exclusion or limitation of consequential damages, so the above limitation and exclusion may not apply to you. All implied warranties on this Product are limited to the duration of this expressed Warranty. Some states do not allow limitation on how long an implied Warranty lasts, so the above limitations may not apply to you. This Warranty gives you specific legal rights, and you also may have other rights which vary from state to state. This Warranty applies only to Products purchased in Canada, the United States of America, its possessions, and U.S. and NATO armed forces exchanges and audio clubs. The Warranty terms and conditions applicable to Products purchased in other countries are available from the Polk Audio Authorized Distributors in such countries.

RM Series Loudspeakers Product Preview
The RM705 System Includes 4 Each RM7 L&R Satellites, 1 RM7C Center And One Powered Subwoofer Features: A Complete 5.1 Home Theater Speaker System that includes 4 RM7 Satellite speakers, 1 RM7C Center Channel and a powered subwoofer. Heavy-duty, Non-Resonant Composite Enclosures create the ideal dcor accent. Three-Sided Cabinet Design minimizes the visual impact on walls and shelves. All RM Speakers Come In An Elegant Black High-Gloss Finish. Accessories Include Flexible Wall Brackets for all speakers and Shelf Cradle for center channel. Downward Firing Powered Subwoofer: A compact vented enclosure with an 8" Long-Throw Dynamic Balance Poly Composite Driver. The long driver excursion and excellent linearity produce big, musical bass. A built-in power amp with active crossover offers the control you need for real home theater thrills. Built-in Subwoofer Power Amp with active crossover offers the control you need for real home theater thrills and big, musical, accurate bass.
The RM705 Complements Todays Stylish High-Tech Flat Panel TVs And Audio Electronics
The new RM705 Home Theater System is a six-piece complete 5.1 channel system that presents a sleek, minimalist design while delivering impressively big sound. Heavy-duty, non-resonant composite enclosures feature an elegant, high-gloss finish that creates the ideal dcor accent. Polk speaker technology ensures superior system performance, delivering rich, full-bodied, big speaker sound. Mount the speakers on shelves, or next to your plasma or flat-screen television using their flexible wall-mount brackets. An included cradle supports the center channel. The RM705 is part of our 700 Series, also available in 6.1 and 7.1 configurations.
All RM Series Satellites Are Magnetically Shielded for safe placement next to todays state-of-the-art TVs and video monitors. Optional FS RM7 Floor Stand visually integrates the RM7 Satellite to create a stunning "mini-tower." (Available Spring 2008) Optional SA3 Floor Stand With RM Adapter works with RM7 or RM8 Satellites. (Note: adapter plates are currently not available with pewter SA3 stands) Individual RM 7 Satellites Are Also Available In High-Gloss White. RM7 Satellites measure just 6 1/8" H x 3 4/5" W x 3 3/4" D, making them virtually disappear. 5.1 System MSRP: $599.95 RM7 Satellite MSRP: $99.95 RM7 Center MSRP: $119.95 Downward Powered Subwoofer

Polk Audio

5601 Metro Drive, Baltimore, MD 21215

1-800-377-7655

www.polkaudio.com
RM8 Wide-Dispersion Array Satellite Loudspeaker
The RM8 Wide-dispersion Array Satellite Loudspeaker ensures more dispersion pattern options for the utmost in placement flexibility. The satellite is offered with a center channel in 5-Pack, 6-Pack and 7-Pack Speaker Systems (subwoofer sold separately). These speaker Pack systems are designated as the 90 Series. A fourth speaker system, designated RM85, is a 5-Pack that includes two RM8 Wide-dispersion Satellites and two RM7 Satellites. RM8 Satellites can also be purchased individually (in black or white) to integrate with any RM700 Series configuration, so you can tailor the kind of surround sound you prefer. RM8 Wide-Dispersion Array Satellite Features: The RM8 Satellite creates a more enveloping, less localizable surround effect. Drivers are mounted on opposing baffles for a broader and larger front stage sound field and a more immersive and atmospheric surround field. Dual-Driver Satellite Design ensures more dispersion pattern options for the utmost in placement flexibility. RM8 Satellite Speakers are sold as left and right speakers for optimized performance. Heavy-Duty, Non-Resonant Composite Enclosures feature an elegant, high-gloss finish that creates the ideal dcor accent. Dynamic Balance Composite Driver Technology delivers wide range response and low distortion for truly lifelike sound. RM8 Satellites Use High-Performance 3/4" (19mm) Silk/Polymer Composite Dome Tweeters for superior imaging and smooth highs. Individual Satellites available for 6.1 and 7.1 systems. Wall Mounting Brackets (Included) For Center Channel And Satellites. Tripod Shelf Bracket (Included) affords even more placement options. Magnetically Shielded for safe placement next to todays state-of the-art TVs and video monitors with no risk of video distortion. RM8 Satellites Available Individually And As 5-Pack With RM8 Center RM8 Satellites Available In High-Gloss Black And High-Gloss White RM8 Satellite MSRP : $299.95 pr RM8 Center MSRP: $149.95
Subwoofer/Satellite Configurations
Model RM705 RM75 Description 4 each RM7 L&R satellites, 1 RM7C center, one Ch. Home Theater powered subwoofer 4 RM7 L&R satellites, 1 RM7C center Packaging & Finishes 6 piece complete 5.1 speaker system 5-pack home theater RM7 speaker systemgloss black only Packaged one to a box gloss black and matte white Packaged one to a box gloss black only 5-pack home theater speaker systemgloss black only Packaged one to a box gloss black and matte white Packaged one to a box gloss black only 5-pack home theater speaker systemgloss black only

RM7SAT RM7C RM85 RM8SAT RM8C RM95
1 each 2 1/2" micro driver, 1 each 1/2" dome tweeter 2 each 2 1/2" micro drivers, 1 each 1/2" dome tweeter 2 RM8 L&R satellites, 2 RM7 L&R satellites, 1 RM8C center 2 each 2 1/2" micro drivers, 1 each 3/4" dome tweeter 2 each 2 1/2" micro drivers, 1 each 3/4" dome tweeter 4 each RM8 Satellite Speakers, 1 RM8 Center Channel Speaker, 5 Wall Mounting Brackets, 1 center channel cradle
Specifications, dimensions and features subject to change without notice. For more information call us at 1-800-377-7655 (USA and Canada). Outside of North America call +1 (410) 358-3600.
Bipole 3/4 view showing driver that reflects off left wall.
Bipole 3/4 view showing driver that reflects off right wall.