TUNERS / CASSETTE / DISC PLAYERS
CHASSIS H CHASSIS W CHASSIS D NOSE H NOSE W SHAFT SP. 13/ 4-/ 8 43/ 4-51/2 15/ 8-13/4 41/ 8-43/ 16 51/ 8-53/4
2 71/ 8 57/ 8-611/ 16 15/ 8-13/4 41/ 8-43/ 16 51/ 8-6
2 71/ 8 57/ 8-611/ 16 23/ 8 71/ 2

ISO DIN

57/ 8-611/ 16 113/ 16 611/ 16
SINGLE DBL DIN 37/ 8 71/ 8 57/ 8-611/ 16 33/ 4-4 611/ 16-71/4

RADIO EQ STACK

3 71/8 57/ 8-611/ 16
UPDATED THROUGH '96 '97 '98 '99

PONTIAC 1993-UP FIREBIRD

Sport Coupe
IN DASH APPLICATION NOTES

KS KS KS KS N KS

APPLICATION KIT MODEL: GM1516, GM1500 Series

HARNESS ADAPTOR:

ANTENNA APAPTOR:
IN-DASH INSTALLATION AREA DIMENSIONS
DEPTH MAX DEPTH WIDTH HEIGHT
CAVITY DASH OPENING DASH MATERIAL:

5 /4" TYPE: PLASTIC

7 /4" M2000

7 /2" 75/8"

THICKNESS:
37/8" 31/4" /16 "

FOR MAX DEPTH

REMOVE REAR SUPPORT MODIFY CAVITY
AMPLIFIER/EQ MOUNTING LOCATIONS (WxHxD)
UNDER/IN DASH UNDER SEAT GLOVE BOX TRUNK/ CARGO
Dimensions shown are inches. For inch/mm conversions refer to chart section.
Vehicle illustration courtesy of NADA Used Car Guide
NOTE: THIS MANUAL IS BASED ON CAREFULLY DOCUMENTED RESEARCH. ABSOLUTE ACCURACY IS ATTEMPTED BUT NOT GUARANTEED. USE THIS MANUAL AS A REFERENCE GUIDE. SCOSCHE, INC. CANNOT BE RESPONSIBLE FOR INCONSISTENCIES THAT MAY OCCUR.
B C1 C2 D D1 D2 D3 F1 F2 K K1 K2 K3 K4
= = = = = = = = = = = = = =
BACK UP PLATES REQUIRED. CUT TRIM/PLASTIC (STRUCTURE). CUT STEEL. BELOW DECK ONLY. LIFT PORTION OF DECK. (MAY REQUIRE STRUCTURAL REINFORCEMENT). CUT STEEL WHEN TOP MOUNTED. DO NOT IF BELOW DECK. NARROW SURFACE, BELOW DECK ONLY. MINIMUM MODIFICATION FILE SHAFT HOLES OR DASH OPENING. MODIFY DASH CAVITY AND/OR PANEL. INSTALLATION KIT, SPACER OR ADAPTOR REQUIRED. KIT MODIFICATIONS REQUIRED. EXTENSION KIT RECOMMENDED. WHEN EQUIPPED WITH FACTORY "ELECTRONIC" RADIO. FABRICATE PANEL/BRACKETS.
K 5 = WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO/TAPE PLAYER. FABRICATE KIT WHEN EQUIPPED WITH FLAT FACE ELECTRONIC RADIO/TAPE PLAYER. K S = SCOSCHE KIT RECOMMENDED. N = NOT RECOMMENDED. EXTENSIVE MODIFICATION REQUIRED. P = PERFECT WITHOUT MODIFICATION. P 1 = MODIFY OR REMOVE POCKETS. P 2 = COIN POCKET LOCATION IN DASH (MAY REQUIRE TRIM KIT). P 3 = PERFECT WHEN EQUIPPED WITH STANDARD TWO SHAFT RADIO, K WITHOUT. R = REAR LOAD ISOMOUNT. U = UNDERDASH. W 1 = WITH POWER WINDOWS ONLY. W 2 = WITHOUT POWER WINDOWS ONLY.

1993-UP PONTIAC FIREBIRD

SPORT COUPE
FACTORY DOOR SPEAKER IN ADAPTOR. DISCONNECT THE NEGATIVE BATTERY CABLE.

PRELIMINARY: ANTENNA:

FENDER.
THE FACTORY ANTENNA IS LOCATED ON THE RIGHT REAR
RADIO REMOVAL AND IN-DASH INSTALLATION:
NOTE: THE FACTORY RADIO PROVISION IS FOR A M2000 STYLE CHASSIS. AN INSTALLATION KIT IS NECESSARY FOR ALL AFTERMARKET APPLICATIONS. WE RECOMMEND THE USE OF THE SCOSCHE GM1500 SERIES KITS. 1. USING A PANEL REMOVAL TOOL CAREFULLY PRY OUT ON THE PERIMETER OF THE RADIO TRIM BEZEL TO RELEASE THE FASTENING CLIPS SECURING THE BEZEL TO THE DASH AND REMOVE THE BEZEL. 2. EXTRACT THE (4) SCREWS SECURING THE RADIO TO THE DASH, PULL THE RADIO OUT OF THE DASH, UNPLUG ALL THE CONNECTORS AND REMOVE THE RADIO.
FRONT DOOR SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 1/2"-7 SPEAKER MOUNTED TO A FACTORY ADAPTOR. (THE OPTIONAL BOSE SYSTEMS COME EQUIPPED WITH THE SAME SPEAKER APPLICATIONS AND AN AMPLIFIER MOUNTED IN THE BOTTOM OF THE DOOR). 1. REMOVE THE COVER CAP LOCATED AT THE FRONT OF THE DOOR PULL HANDLE/ARMREST BELOW THE DOOR RELEASE HOUSING. 2. EXTRACT THE SCREW IN THE DOOR RELEASE HOUSING SECURING IT TO THE DOOR, ADJUST THE LOCK LEVER TO THE LOCK POSITION. 3. CAREFULLY PRY OUT ON THE HOUSING WITH A PANEL REMOVAL TOOL TO RELEASE THE FASTENING CLIPS SECURING THE HOUSING TO THE DOOR, REMOVE THE HOUSING AND EXTRACT THE SCREW SECURING THE DOOR PANEL BEHIND THE HOUSING. 4. EXTRACT THE SCREW SECURING THE DOOR PANEL TO THE DOOR LOCATED NEAR THE MIDDLE OF THE ARMREST WITH THE SCREW GOING INTO THE DOOR FROM THE UNDERSIDE OF THE ARMREST. 5. EXTRACT THE SCREW SECURING THE DOOR PANEL TO THE DOOR LOCATED AT THE BOTTOM OF THE MAP POCKET. 6. USING THE SPECIAL WINDOW CRANK REMOVAL TOOL REMOVE THE WINDOW CRANK WHEN SO EQUIPPED. 7. PRY OUT ON THE PERIMETER OF THE DOOR PANEL WITH A PANEL REMOVAL TOOL TO RELEASE THE POP PIN FASTENERS SECURING THE DOOR PANEL TO THE DOOR. 8. EXTRACT THE (4) SCREWS SECURING THE SPEAKER TO THE DOOR, PULL THE SPEAKER OUT OF THE DOOR, UNPLUG THE SPEAKER LEADS AND REMOVE THE SPEAKER.

REAR SEAT SIDE PANEL SPEAKER LOCATION.
REAR SEAT SIDE PANEL SPEAKER INSTALLATION:
NOTE: THE FACTORY SPEAKER PROVISION IS FOR A 6 1/2"-7 SPEAKER. AN ADAPTOR IS REQUIRED FOR AFTERMARKET INSTALLATIONS. 1. CAREFULLY PRY OUT ON THE SPEAKER GRILLE WITH A PANEL REMOVAL TOOL TO RELEASE THE FASTENING CLIPS SECURING THE GRILLE TO THE REAR SEAT SIDE PANEL. 2. EXTRACT THE (4) SCREWS SECURING THE SPEAKER TO THE REAR SEAT SIDE PANEL, PULL THE SPEAKER OUT OF THE SIDE PANEL, UNPLUG THE SPEAKER LEADS AND REMOVE THE SPEAKER.
REAR SEAT SIDE PANEL 6-1/2 GM MOUNTING PATTERN.