6001_14.6.fh9 14/6/06 15:11 Page 1

C M Y CM MY CY CMY K

PowerDsine 6001
Single-Port Power over Ethernet Midspan
PowerDsine 6001 is a single-port Power over Ethernet midspan, providing power as well as data over Ethernet cabling. Incorporating IEEE 802.3af compliance, as well as PowerDsines unique legacy detection, the PowerDsine 6001 powers virtually any Power over Ethernet ready device.

Ethernet Switch

PowerDsine 6001 Power over Ethernet Midspan
Wireless LAN Access Point VoIP Phone Networ Camera Splitter

Benefits Features

Powers all major Wireless LAN and Bluetooth access points, Network cameras and IP phones in the market Remote power for scattered topology devices Safe powering Easy and simple installation Continuous monitoring of the powered device Backup capability of the powered device Wall and shelf mountable IEEE 8023af compliant Cost-effective installation, saving electrician installation costs Effective powering for lower density installations Automatic detection and protection of legacy non-powered Ethernet terminals No need for bulky AC adapter, power cord and a local UPS Identification of faulty powered devices and safe shut down to protect the infrastructure and device Backup of the PowerDsine 6001 in the communication room guarantees continuous operation of WLAN APs and security cameras Firmly fixed in the communication room

Composite

6001_14.6.fh9 14/6/06 15:11 Page 2
PowerDsine 6001 Single-Port Power over Ethernet Midspan

IEEE 802.3af Compliant

Description of Features
Remote Power Feeding The PowerDsine 6001 Power over LAN midspan connects to an existing Ethernet infrastructure via any standard Category 5 cabling. By sending 48 V, Ethernet terminals (IP phones, wireless LAN access points and network cameras) can be powered by the PowerDsine 6001 midspan. An external splitter is installed where a device is not compatible with Power over Ethernet. This splitter separates the required DC voltage and the Ethernet data, into two separate outputs. Scalable Solution The PowerDsine 6000 Power over Ethernet Family includes the PowerDsine 6001, 6006, 6012 and 6024 Power over LAN midspans, featuring 1, 6, 12 and 24 ports, respectively. Centralized Power Distribution Deploying Power over Ethernet midspan in conjunction with a UPS enables distribution of back-up power to ensure uninterrupted operation of the powered devices. Smart Ethernet Wiring The PowerDsine 6001 directly transfers data over pairs 1/2 and 3/6. The PowerDsine 6001 acts as a normal patch panel for Ethernet connections, ensuring continuous and reliable performance. Power is provided only over unused Ethernet pairs 4/5 and 7/8. Standard Compliance PowerDsine 6001 midspan is fully compatible with IEEE 802.3 standard (when no inline power is supplied) and with IEEE 802.3af, DTE Power via Media Dependent Interface (MDI). Advanced Auto-Sensing Algorithm PowerDsine 6001 midspan features a standard IEEE 802.3af auto-sensing detection algorithm, as well as backward compatibility to the pre-standard algorithm. This algorithm ensures continuous proper operation of devices, such as ordinary Network Interface Cards (NICs) that do not expect power on their Ethernet connection. Easy to Use The PowerDsine 6001 Power over Ethernet midspan is a plug-and-play product. Once turned on, they automatically detect all Power over Ethernet Ethernet terminals and supply power. All port interfaces are located on the front panel for easy access. The PowerDsine 6001 Power over Ethernet midspan can be wall or shelf mounted.

Specifications

No. of Ports Data Rates Power over LAN Output 1 10/100 Mbps Pin Assignment and Polarity: 4/5 (+), 7/8 (-) Output Power Voltage: -48 VDC User Port Power: 15.4 W min. AC Input Voltage: 90 to 264 Vac AC Frequency: 47 to 63 Hz AC Input Current : 0.34 A at 110 Vac, 0.17 A at 240 Vac (H) 1.75 in. x (W) 4.17 in. x (D) 5.5 in. (H) 44.4 mm x (W) 106 mm x (D) 140 mm Weight: 1.0 lbs (450 g) System Indicator: AC Power (Green) User Indicator: Channel Power Active (Green) Shielded RJ-45, EIA 568A and 568B Operating Ambient Temperature: 32 to 104F (0 to 40C) Operating Humidity: Maximum 93%, non-condensing Storage Temperature: -4 to 158F (-20 to 70C) Storage Humidity: Maximum 95%, Non-condensing Operating Altitude: -1000 to 10,000 ft. (-304.8 to 3048 m) 50 BTU/hrs (-48Vdc) CE

Input Power Requirements

Dimensions

Indicators

Connectors Environmental Conditions
Thermal Rating Regulatory Compliance
2004 PowerDsine. All rights reserved. Information in this document is subject to change without notice. PowerDsine is a trademark of PowerDsine. Serial No. PD-PH-6001/AC/48 Ver03 03/04
Electromagnetic FCC Part 15, Class B with FTP Cabling Emission & Immunity EN55022 (CISPR22),Class B with FTP Cabling EN55024 (CISPR24) Safety Approvals UL/cUL Per EN60950 GS Mark Per EN60950
Ordering Information Single-Port Power over Ethernet Midspan

PD-6001/AC AC input

International Headquarters PowerDsine Ltd. 1 Hanagar St., P.O.Box 7220 Hod Hasharon 45421 Israel Tel: +972-9-7755100 Fax: +972-9-7755111 sales@powerdsine.com
North America PowerDsine, Inc. 1865 New Highway Farmingdale, NY 11735 USA Tel: +1-631-756-4680 Fax: +1-631-756-4691 sales@powerdsineusa.com
Europe PowerDsine UK Lakeside House 1 Furzeground Way Stockley Park, Uxbridge UB11 1BD, United Kingdom Tel: +44 (0) 3107 Fax: +44 (0) 3200 uk@powerdsine.com

www.powerdsine.com

Safety Information (cont.) ~

WARNING

Read the installation instructions before connecting the Power over LAN Hub to its power source.
Follow basic electricity safety measures whenever connecting the Power over LAN Hub to its power source.
1-Port Power over LAN Hub

User Guide

Notice
It is PowerDsines policy to improve its products as new technology, components, software, and firmware become available. PowerDsine, therefore, reserves the right to change specifications without prior notice.
This product relies on the building installation for short-circuit (over current) protection. Ensure that a fuse or circuit breaker no larger than 120 VAC, 3A. U.S. (240 VAC, 1.5A international) is used on the phase conductor.
A voltage mismatch can cause equipment damage and may pose a fire hazard. If the voltage indicated on the label is different from the power outlet voltage, do not connect the Power over LAN Hub to this power outlet.

Trademarks

The product described in this guide is a licensed product of PowerDsine. Power over LAN is a trademark of PowerDsine Ltd.
The Power over LAN Hub "Data In" and "Data & Power Out" ports are shielded RJ-45 data sockets. They cannot be used as Plain Old Telephone Service (POTS) telephone sockets. Only RJ-45 data connectors may be connected to these sockets.

Technical Support

If you encounter problems when installing or using this product, please consult the PowerDsine website at: http://www.powerdsine.com If these resources dont provide the help you need, please contact your local authorized PowerDsine reseller for additional technical support. 2002 PowerDsine All Rights Reserved. P/N Y1-6040-010 Rev. A0

Functions and Features

The device is design to meet the IEEE802.3af standard
The Power over LAN Hub adds 48VDC to the unused (non-data) wires in standard Category 5 Ethernet cable. As a result, the Power over LAN Hub delivers both data and power to the terminal. EMC Compliance: Category 5 foiled twisted-pair cables must be used to ensure compliance with requirements of FCC Part 15, subpart B, Class B. The use of unshielded cables (Category 5 for 10BASE-T ports or for 100BASE-Tx ports) complies with Class A requirements.

Indicators

Main Led - steady green indicates that the power is on. Active Led - steady green indicates that the terminal is connected. (Power is active)

Troubleshooting

Ensure AC power is applied to the Power over LAN Hub, using an operational AC cable with an appropriate ground connection. Ensure the use of a standard 4 pair (8 wires) UTP or FTP CAT5 cable. Ensure a crossover type Ethernet cable is not used. Ensure input Ethernet cable is connected to the Data In port. Ensure output Ethernet cable is connected to the Data & Power Out port. Verify that the Ethernet cable length is less than 100 meters from the Ethernet source to the load. Verify that power ready Ethernet compatible device is connected. Verify that you are not using any cross over cable between the Power over LAN Hub output port and the load device. Verify that there is no short over any of the twisted pair cables or over the RJ45 connectors.

Specifications

Environmental Specifications Mode Operating Storage Temperature 0 to 50 C 32 to 122F -20 to 70 C -4 to 158F Humidity 10 to 90% (no condensation allowed) 10 to 90% (no condensation allowed)

Installation

The Power over LAN Hub may be free standing or wall mounted using the back wall holders. NOTE: Before you mount the Power over LAN Hub to a fixed location: Ensure not to cover the Power over LAN Hub or block the airflow to the Power over LAN Hub with any other objects. Keep the Power over LAN Hub away from excessive heat and humidity, and free from vibration and dust. Ensure that the cable length from the Ethernet network source to the terminal does not exceed 100 meters (333 Feet). The Power over LAN Hub is not a repeater and does not amplify the Ethernet data signal Installing the Unit Connect the Power over LAN Hub to an AC outlet (100240 VAC), using a standard power cord. Connect the unit Data In jack (input) to the Ethernet network and the Data & Power Out jack (output) to the terminal.
Electrical Specifications Input Voltage Input Current at 110 VAC Input Current at 220 VAC Minimum Available Output Power Nominal Output Voltage Ethernet Interface Input (Data In): Ethernet 10/100Base-T Output (Data & Power Out): Ethernet 10/100Base-T, plus 48 VDC RJ 45 female socket RJ 45 female socket, with DC voltage on wire pairs 7-8 and 4-5. 90 to 264 VAC (47-63 Hz) 0.34 ampere (max) 0.17 ampere (max) 15.4 Watts 45 to 56 VDC

Safety Information

Important Safety Information Installation and removal of the Power over LAN Hub must be carried out by qualified personnel only. AC Power Cord Set: q The power cord must have regulatory agency approval for the specific country in which it is used (i.e., UL, CSA, VDE, etc.). q The power cord must be a three-conductor type (two current carrying conductors; one ground conductor) terminated on one end by an IEC 60320 appliance coupler (for connection to the Power over LAN Hub), and on the other end by a plug containing a ground (earthing) contact. q The power cord must be rated for a minimum of 250Vac RMS operation, with a minimum rated current capacity of 5 amps (or a minimum wire gauge of 18 AWG (0.75mm2)). Note: Power over LAN Hub units installed in Australia require power cords with a minimum wire gauge of 16 AWG (1.0 mm2). The AC wall socket-outlet must be near the Power over LAN Hub and easily accessible. You can remove AC power from the Power over LAN Hub by disconnecting the AC power cord from either the wall socket-outlet or the Power over LAN Hub appliance coupler. The Power over LAN Hub data and data / power interfaces are qualified as SELV (Safety Extra-Low Voltage) circuits according to IEC 60950. These interfaces can only be connected to SELV interfaces on other equipment.

PowerDsine 6001

Data & Power Out Data In
Port Connectivity Indicators

Power Active

IEEE 802.3af Compliant

Port Output

Port Input

Cat. 5 Cable

Terminal

Ethernet

Figure 1: Illustration of connectivity for the Power over LAN Hub. NOTE: There is no on-off switch. Simply plug the Power over LAN Hub into an AC power source.