co_SRE30x.qxd

22-05-2009

Pagina 2

SRE 30x

GUARANTEE

> 1

MANUEL D'UTILISATION GEBRAUCHSANWEISUNG INSTRUCCIONES DE USO OPERATING MANUAL ISTRUZIONI DUSO GEBRUIKSAANWIJZING

Pagina 1

SRE 30x: Eurostove SRE 301 Appliance SRE 302
> 1 Sous rserve de modification ndrungen vorbehalten Nos reservamos el derecho de hacer modificaciones Subject to modifications Sogetti a modifiche Wijzigingen voorbehouden

p38_49_uk_SRE30x.qxd

Pagina 38

Dear Sir, Madam,

Congratulations with your purchase of a portable domestic heater. You have purchased a quality product, which will serve you for many years to come. This, of course, if you use the heater correctly. Please read this user manual first, to ensure maximum lifetime for your heater. Your heater comes with a 24-month manufacturers warranty on all defects in materials or workmanship.
We wish you a warm and comfortable time with your heater.

Yours sincerely,

PVG International b.v. Customer Service Department
1 READ THE OPERATION MANUAL FIRST.
2 IN CASE OF ANY DOUBT, CONTACT YOUR DEALER.

Pagina 39

MAIN COMPONENTS

Tank cover Fuel gauge (back) Overheat protection device Front panel Inspection window Warm air outlet Fixed tank Removable tank Fuel cap Handle Control panel Fuel filter Fuel pump Base plate Room thermistor Power cord Vent filter Air filter

Pagina 40

GENERAL DIRECTIONS FOR USE
Below you will find the main steps to be taken for using your heater. For more details, please refer to Section A.
Remove all packaging materials (refer to Section A). Fill the removable tank (refer to Section B). Insert the plug into the wall-socket. Ignite the heater using the key (refer to Section D).
If required, change the temperature using the adjustment buttons (refer to Section F). Switch off the heater by pressing the H). key. (refer to Section
As a fire precaution, the tank must be filled either when the heater has been switched off or in another room than the room where the heater is installed. Always ensure that the tank is closed properly after filling it at a safe distance from all sources of heat and open flames (see chapter B). The first time the heater is ignited it will smell like new for a short time. Store all fuel containers with their original caps and seals in a cool and dark place. Fuel ages. Use new fuel at the start of every heating season. The use of Zibro Extra, Zibro Kristal or Zibro Bio as a heating fuel assures you that you have a good quality fuel. Before changing brands and/or types of fuel make sure that the mobile heater first completely empties all of the remaining fuel inside the heater.

Pagina 41

WHAT YOU NEED TO KNOW IN ADVANCE
VENTILATE SUFFICIENTLY Regardless of the model, you must always make sure that the heater is used in a
room large enough to enable the heater to be used safely without extra ventilation. If the room is smaller than required, you must always open a door or window slightly (ensuring an opening of approx. 2.5 cm). It is important that every room where the heater is used has sufficient air intake and efficient air outflow (both openings must have a minimum cross section of 50 cm2 ). No modifications to the safety system are allowed, as that will invalidate the guarantee that the air probe will work properly. Consult your dealer in case of doubt. Especially for France: Your heater was designed to operate exclusively on fuel for liquid fuel-operated mobile heaters in accordance with the Decrees of 08-01-1998 and 18-07-2002. The use of other fuels is forbidden. Ask your dealer or check our website for the addresses of our retailers. The liquid fuel-operated mobile heater is intended as an extra heater, and not as a continuous source of heat. Especially for United Kingdom: Only use Class C1 paraffin fuel in accordance with BS2869; Part 2, or equivalent. The user must comply with the following instructions for proper use: DO NOT - use the liquid fuel-operated mobile heater in caravans, boats, and vehicle cabins; - use the liquid fuel-operated mobile heater in insufficiently ventilated rooms
Only the use of the correct fuel will ensure safe, efficient, and comfortable use of your heater.

(consult the table of properties for the minimum dimensions of the room to be heated), underground rooms and / or at a height of over 1500 metres; - modify the heater safety features. The use of this type of heating in public rooms is subject to prior regulatory permission. Obtain proper information on this in advance.
THE RIGHT FUEL Your heater has been designed for use with high-quality water-free pure paraffin
oil, such as Zibro Extra, Zibro Kristal or Zibro Bio. Only fuels of this kind will ensure clean and proper burning. Lower quality fuel may result in: increased possibility of malfunctioning incomplete combustion reduced heater lifetime smoke and/or fumes deposits on the grid or mantle
Using the right fuel is therefore essential for safe, efficient, and comfortable use of your heater. Damage and/or malfunctions of the heater due to the use of other than highquality water-free pure parafine oil is not covered by the warranty. Always refer to your local dealer for the right fuel for your heater.

Pagina 42

MANUAL
This transportation cap is packed separately in the box. Only this cap ensures trouble-free transportation of the heater after use. Store it well! A

INSTALLING THE HEATER

1 Carefully remove your heater from the box and check the contents. In addition to the heater you also need to have: a transportation cap this operating manual Keep the box and the packaging materials (Fig. A) for storage and/or transportation. 2 Open the lid of the removable tank and remove the piece of cardboard. 3 Fill the removable tank as indicated in Section B. 4 The floor should be firm and completely level. Reposition the heater, when it is not level. Do not try to correct the situation by placing books or other goods under the heater. 5 Insert the plug into the wall-socket (230 Volts - AC 50 Hz) and set the correct time using the adjustment buttons (refer to Section C). 6 Your heater is now ready for use.
FILLING FUEL Fill the removable tank in a suitable place since there can always be some spillage.
Follow the procedure below: 1 Make sure that the heater is switched off (refer to Section H).
2 Open the upper lid and lift the removable tank out of the heater (Fig. B). Note: Some drops may leak from the tank. Put down the removable tank (cap pointing upwards, handle on floor (Fig. C) and screw off the fuel cap. 3 Fill the removable tank using a fuel pump (refer to fuel pump operation instructions.) Make sure that it is in a higher position than the removable tank (Fig. C). Insert the ribbed hose into the opening of the removable tank. 4 Check the removable tank fuel gauge while filling the tank (Fig. D). Stop filling once the gauge indicates that the tank is full. Never overfill the tank,

especially not when the fuel is very cold (fuel expands when it heats up). 5 Let the remaining fuel in the pump flow back into the jerrycan and carefully remove the pump. Carefully screw the fuel cap back on the tank. Clean off any spilled fuel.

Pagina 43

6 Check whether the fuel cap is straight and tightened properly. Reinstall the removable tank in the heater (cap down). Close the lid.
SETTING THE CLOCK It is only possible to set the correct time, when the heater is connected to mains.
Press the mode key once and the word TIME will appear on the display. Use the + and buttons to enter the actual time.
When the heater has been unplugged (or after a power failure), the time needs to be set again.
IGNITING THE HEATER (Auto restart) When used for the first time, a new heater may give out some fumes for a short
while. You therefore have to provide extra ventilation. Always ignite the heater with the lighter. A little white smoke and smell during ignition is normal. Just press the to ignite the heater. The green power lamp inside the button button. Never use matches or a cigarette
button will start to blink, will light
indicating that the ignition procedure is running. This will take about 2 or 3 minutes. Once the heater is really burning, the power lamp continuously. This heater will restart automatically after a power cut when the heater was in on position prior to power cut. This makes it possible to switch the appliance on / off by interrupting / enabling the power supply (for instance through a mobile phone switch).
QUICK IGNITION Sometimes you may know in advance that you will be manually switching on the
heater within 12 hours, but you do not want to wait 2-3 minutes (see chapter D) at that particular moment. For these occasions this heater is equipped with the quick ignition function. This function will prepare the heater such that at the moment you want to switch on the heater that upon pressing the quick ignition button. In quick ignition mode: - the electrical power consumption is 100 Watt - the air at the outlet is slightly warmed - is automatically cancelled when timer function is set - is automatically switched off after 12 hours - can be cancelled by pressing the QUICK IGNI. button again. (The light will now be off). The quick igition mode has to be enabled for at least 2-3 minutes before the heater can be started. button the heater will start within 5 seconds. To start the QUICK IGNI. function press the

SETTING THE REQUIRED TEMPERATURE The temperature setting can only be adjusted when the heater is burning. Use the
buttons + and to adjust the temperature. The available temperature range is +6C minimum to +30C maximum. The desired temperature is stored in the memory and remains after a restart or power failure.

Pagina 44

USING THE TIMER The timer allows you to activate the heater at a certain time. In order to use the
timer, the correct actual time must have been set (refer to section C). To set the timer: Press the mode button twice and the word TIMER will appear on the display. Use the buttons + and to set the time at which the heater has to start. Press the button first, then press the TIMER button within 1 sec. The TIMER lamp switches on and the heater is ready to start at the desired time.
SWITCHING OFF THE HEATER Press the button. The green lamp inside the
the extinguish period is normal.
button will switch off and the
heater stops within approximately 1 minute. A little white smoke and smell during
SAVE MODE In the save mode the heater will switch off when the room temperature, as sensed
by the heater, rises 3C above the set temperature. The save mode can be activated with the button SAVE. The lamp in the button will switch on and the heater will now switch off when the room temperature rises 3C above the set temperature. The heater will start again when the room temperature drops below the set temperature. The save mode can be cancelled by pushing the SAVE button again, the lamp switches off.
THE INFORMATION DISPLAY The information display not only serves as an indicator of the (set) time and
temperature, it also indicates any malfunctioning of the heater. The code on the information display tells you what is the matter: CODE CAUSES No flame during ignition. WHAT TO DO Check fuel, restart the heater. Read section Q point 5. Use correct fuel (see section The right fuel).

Flame sensor failure

Check fuel, restart the heater. Read section Q point 5. Use correct fuel (see section The right fuel).

No flame after ignition.

Poor flame during normal burning. Check fuel, ventilate the room,

Pagina 45

restart the heater. Read section Q point 5. Use correct fuel (see section The right fuel).
e- 5 e- 6 e- 7 e- 9 e-A e-H KL FUEL TIME TIMER
Ignition temperature too low. Ignition temperature too high.

Disconnected the mains plug and restart. Cool down, disconnect the mains plug and restart.
Wrong blower speed. Tilt switch. Room temperature > 35C Electronics temperature > 60C KEY LOCK. Out of fuel. The heater shows the actual time The heater shows the set time for timer The heater has been operating
Disconnect the mains plug and restart. Avoid shocks. The heater must be levelled. Ventilate the room and restart the heater. Ventilate the room and restart the heater. Push the button KEY LOCK 3 times to unlock the heater. Refill the removable tank. Check if the fuel filter contains water. Push the and + buttons to adjust the time. Push the and + buttons to adjust the set time when the heater has to start. Switch the heater on again.
continuously for a period of 48 hours and has switched itself off (refer to section K). Always contact your dealer for any malfunctioning not listed above and/or when the error keeps occuring after taking the corrective measure as described above.
AUTOMATIC DEACTIVATION This heater is equipped with a safety system that ensures that it switches off
automatically after 48 hours of continuous operation. The display will show:. Switch on the heater by pressing the button.
KEY LOCK The key lock can be used to prevent children accidentally starting the heater. Press
the button KEY LOCK 3 times when the heater is off. The characters KL will appear in the display. All keys are blocked now, the heater will not respond to any pressing of the buttons. Press the button KEY LOCK again 3 times to release the key lock. The status of the KEY LOCK is memorized and remains after a power interrupt.
THE 'FUEL' INDICATOR When low on fuel level the display will show FUEL. The heater will stop within
10-15 minutes. It will take some time after a refill before the heater is ready for use again when the heater has used all its fuel.

Pagina 46

HIGH ALTITUDE ADJUSTMENT The factory setting is for meters above sea level. This setting needs to be
changed for higher altitudes to increase the blower speed and keep the combustion correct. Before changing the high altitude setting always remove the mains plug!
Factory setting: switch 1 & 2 are in OFF position (down).
Remove the two screws beside the front panel. A small block with 4 switches on the main electronics board becomes visible. Always leave switch 3 and 4 in the original position. Altitude (m) 0 - - -1500 Switch 1 OFF OFF ON Switch 2 OFF ON OFF

WARNING Never insert the mains plug when fixed front panel is not fixed!
MAINTENANCE Switch off the heater, disconnect the plug from the mains and let it cool down,
before you start any maintenance work. Your heater needs hardly any maintenance. It is, however, important that you clean the air filter and the vent filter with a vacuum cleaner and a brush and the grid with a damp cloth, both on a weekly basis. Remove the air filter occasionally and clean it with soapy water or with a vacuum cleaner. Prior to reinstallation, make sure that the air filter cap has fully been dried. Regularly inspect the fuel filter as well: 1 Remove the removable tank from the heater and remove the fuel filter Some drops may leak from the filter; keep a cloth at hand. 2 Remove the dirt and water by gently tapping the fuel filter upside-down against a hard surface. (Never clean it with water!) 3 Reinstall the fuel filter into the heater. We recommend to remove dust and stains on the outside of the heater from time to time with a damp cloth, otherwise these may cause stains that are hard to remove.

Fuel filter

Do not remove any components yourself. Always contact your dealer for repairs. When the power cord is damaged, it may only be replaced by an authorised engineer. Use a new original cord.

Pagina 47

STORAGE (END OF THE HEATING SEASON) At the end of the heating season, store the heater in a dust-free place in its
original packaging. Any unused fuel cannot be used the next heating season. We therefore recommend that you burn up all fuel prior to storing. If there is still some fuel left, do not throw it away, but dispose of it in accordance with the local regulations for the disposal of domestic chemical waste. Always start the new heating season with fresh fuel. When you start re-using the heater follow the instructions again (starting from section A and as specified).

transportation cap

TRANSPORTATION Take the following measures to avoid fuel leakage during the transportation of

the heater: 1 Let the heater cool down. 2 Remove the removable tank from the heater and remove the fuel filter. Some drops may leak from the filter; keep a cloth at hand. Store the fuel filter and the removable tank outside the heater. 3 Place the transportation cap into the position of the fuel filter. Press it tight. The transportation cap will, as much as possible, prevent oil leakage from the heater during transport. 4 Always move the heater in an upright position. 5 Make the fixed tank empty with a fuel pump before transportation or in case of wrong or dirty fuel. First remove the fuel filter and then insert the fuel pump into the empty fixed tank. Follow the same procedure if the fuel tank contains water.

SPECIFICATIONS

IGNITION FUEL SUITABLE SPACE MIN-MAX HEATING CAPACITY MIN-MAX MAINS ELECTRIC CONSUMPTION BURNING ELECTRIC CONSUMPTION IGNITION ELECTRIC CONSUMPTION QUICK IGNITION MODE WEIGHT FUSE RATING DIMENSIONS (HxWxD) ACCESSORIES REMOVABLE TANK CAPACITY BURNING TIME PER TANK (100% CAPACITY) ELECTRICAL PARAFFIN 40 - 120 mkW (83 g/h) 3.0 kW (250 g/h) 230 V~ / 50 Hz 22 W 660 W 100 W (heater not burning) 10 kg 5 A / AC 250 V / 5 X 20 mm 45.5 x 40 x 30.7 cm TRANSPORTATION CAP 5 LITRES 16 h
Specified values are indicative

Pagina 48

WARRANTY PROVISIONS Your heater comes with a 24-month warranty starting on the date of purchase.
Within this period all defects in material or workmanship will be repaired without any charge. The following provisions shall apply regarding this warranty: 1 We expressly dismiss all other claims for damages, including consequential damages. 2 Any repairs or replacements of components within the term of warranty will not result in an extension of the term of warranty. 3 The warranty shall no longer apply, when the heater has been modified, non-original parts have been used, or when it is repaired by third parties. 4 The warranty shall not apply to parts that are subject to normal wear.
5 The warranty shall only apply, when you present the original, dated proof of purchase, provided no changes have been made to it. 6 The warranty shall not apply to damages caused by actions not in compliance with this operating manual, neglect, and the use of an incorrect type of fuel, or fuel past its use-by date. The use of incorrect fuel can even be dangerous*. 7 Transportation costs and the risks involved during the transportation of the heater or heater components shall always be at the expense of the purchaser. In order to avoid unnecessary costs, we recommend that you always read this operating manual carefully first. In case they offer no solution, please take the heater to your dealer for repair.

* Highly inflammable substances may induce uncontrollable burning, causing flames to break out. Should this happen, never try to move the heater, but always switch off the heater immediately. In case of emergency you may use a fire extinguisher, but only a type B extinguisher: a carbon dioxide or powder extinguisher.

11 TIPS FOR SAFE USE

1 This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Do not move the heater when it is burning or still hot. Do not refill nor service the heater when it is burning or still hot. Position the front of the heater at a distance of minimum 1.5 metres from walls, curtains, and furniture. Do not use the heater in dusty rooms or places with strong draughts. In either situation you will not have optimum burning. Do not use the heater in the immediate surrounding of a bath, a shower or a swimmingpool. Switch off the heater, before you leave or go to sleep. Unplug the heater as well, when you go away for a longer period of time (e.g. holidays).

Pagina 49

Store and move fuel only in suitable tanks and jerrycans. Make sure that the fuel is not exposed to heat or extreme temperature changes. Always store the fuel in a cool, dry and dark place (sunlight will affect the quality). Never use the heater in places where harmful gasses or fumes may be present (e.g. exhaust gasses or paint fumes). Beware that the grid of the heater becomes hot. If the appliance is covered there is a risk of fire. Always make sure that there is sufficient ventilation. Children should be supervised to ensure that they do not play with the appliance.
Waste electrical products should not be disposed with household waste. Please recycle where facilities exist. Check with your local authority or retailer for recycling advice.

Pagina 4

Pagina 3
DISTRIBUTED IN EUROPE BY PVG INTERNATIONAL BV
i STERREICH PVG Austria VertriebsgmbH Salaberg HAAG tel: +44867 fax: +44868 email: pvgaustria@zibro.com e BELGI PVG Belgium NV/SA Industrielaan SCHOTEN tel: +39 fax: +39 email: pvgbelgium@zibro.com q SCHWEIZ PVG Schweiz AG Salinenstrasse PRATTELN +51 tel: fax: +78 email: pvgint@zibro.com 2 DEUTSCHLAND PVG Deutschland GmbH Siemensstrasse KLEVE 0800 - 9427646 tel: fax: +31 (0)385 email: pvgdeutschland@zibro.com 6 DANMARK Appliance A/S Gefionsvej 7 DK-3400 HILLERD tel: +fax: +email: appliance@appliance-group.com 5 ESPAA PVG Espaa S.A. Pol. Ind. San Jos de Valderas II Comunidad La Alameda C/ Aurora Boreal, LEGANS (Madrid) tel: +13 fax: +04 email: pvgspain@zibro.com 3 FRANCE PVG France SARL 4, Rue Jean Siblius B.P. SOTTEVILLE SOUS LE VAL tel: +fax: +email: pvgfrance@zibro.com