Heavy Duty 7-Day Digital Timer
OWNERS MANUAL Please read before using this equipment.
Your RadioShack Heavy Duty 7-Day Digital Timer gives you an easy way to program a lamp, TV, stereo, or other appliance to operate automatically in a set or random pattern. Its features include: Up to 98 ON/OFF Weekly Settings let you program one appliance to turn on and off up to 14 times a day, every day of the week. Random Switch Setting turns the appliance on for five minutes to an hour (in a random pattern) four to 12 times a day to avoid a predictable timer-controlled look. Manual Override lets you turn the automatic timer on and off when you desire. Various Length Settings let you program the timer to operate only on a particular day of the week, every day, only weekdays, only weekends, or every day but Sunday. Highly Accurate the timer is accurate to the minute, providing you with precise timing in any setting. Your Heavy Duty 7-Day Digital Timer is listed to UL standards and meets all applicable FCC requirements.
WARNING: To reduce the risk of fire or
shock hazard, do not expose this product to rain or moisture.

CAUTION

RISK OF ELECTRIC SHOCK. DO NOT OPEN.
CAUTION: TO REDUCE THE RISK OF
ELECTRIC SHOCK, DO NOT REMOVE COVER OR BACK. NO USER-SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED PERSONNEL.
This symbol is intended to alert you to the presence of uninsulated dangerous voltage within the products enclosure that might be of sufficient magnitude to constitute a risk of electric shock. Do not open the products case.
This symbol is intended to inform you that important operating and maintenance instructions are included in the literature accompanying this product.
Warning: Do not use the timer to turn off power for maintenance (repairs, removing broken bulbs, etc.). Always turn power off at the service panel by removing a fuse or circuit breaker before doing any circuit repairs.
INSTALLING THE BACKUP BATTERIES
Your timer requires two L1154 button-cell batteries (supplied) for power. For the best performance and longest life, we recommend RadioShack alkaline batteries.
2001 RadioShack Corporation. All Rights Reserved.
RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.
The batteries retain the program during power outages. After removing the batteries, you have 15 seconds to insert new batteries without losing any programs. Warning: Keep button-cell batteries away from children. Swallowing a button-cell battery can be fatal. Cautions: Use only fresh batteries of the required size and recommended type. Do not mix old and new batteries, or different types of batteries. Follow these steps to install batteries. 1. Unplug the timer. 2. Use a small, flat screwdriver to remove the battery carrier. 3. Place both batteries in the compartment as indicated by the polarity symbols (+ and ) marked inside. 4. Align the notch on the battery carrier with the indention in the holder, then slide the carrier into place. 5. Plug the timer into an outlet. When the display dims or is weak or unreadable when the timer is unplugged from an outlet, replace the batteries. When you replace the batteries, follow Steps 15. If the display goes blank, use a straightened paper clip to press RESET. Warning: Dispose of old batteries promptly and properly. Do not burn or bury them. Caution: If you do not plan to use the timer for an extended period of time, remove the batteries. Batteries can leak chemicals that can destroy electronic parts.
A QUICK LOOK AT THE DISPLAY
Daylight Savings Symbol appears when it is Daylight Savings time. Hold down DS to turn the symbol off. On/Off Symbol indicates the timer is on or an on time is being programmed. A light bulb with an X on it indicates the timer is off or an off time is being programmed.
AM/PM Setting indicates the time of day.
Day shows the current day of the week.
Program Symbol the number to the right of this indicates which program is running.
Countdown Timer Clock appears when the timer is in countdown mode.
Mode Indicator shows which mode the timer is currently in.

SETTING THE CLOCK

Before you program the clock, the timer must be set to On, Auto, or Off. The appliance can be on or off. Note: If it is Daylight Savings time, hold down DS for a couple of seconds until the Daylight Savings symbol appears. If it is not Daylight Savings time and the Daylight Savings symbol is on, hold down DS for a couple of seconds until the symbol turns off. The Daylight Savings symbol (6) appears or disappears and the time switches one hour in the appropriate direction. 1. Push and hold TIME SET. The blinking colon stops blinking and appears steadily. 2. While holding TIME SET: Repeatedly press DAY to change the day of week. Repeatedly press HOUR to change the hour and AM/PM. 2
Repeatedly press MIN to change the minutes. Notes: If you hold down DAY, HOUR or MIN the display changes quickly. Seconds are set to 0 when the TIME SET button is released if either the hour or minutes have been set.
When the countdown reaches 33=33/ the connected appliance is switched on or off and the clock display remains 33=33.

Off Mode

In Off mode, the appliance is off. Press ON/ OFF to switch to On mode to turn the appliance on. appears when the timer is off (or when you are programming an off time).

SETTING THE MODE

Repeatedly press MODE to select Countdown Timer, Off, Auto, On, or Random.

Auto Mode

In Auto mode the programmed on and off times automatically switch the appliance on and off. Press ON/OFF while in Auto mode to manually override the program and turn the appliance on or off. The programmed switching times remain, and the timer remains in auto mode.

Countdown Timer Mode

The countdown timer lets you set the timer for 15, 30, 45, 60 or 75 minutes. Once the countdown timer is set, the appliance turns on or off after the set time. Note: The countdown time is preset to turn the appliance on or off after 75 minutes. Follow these steps to set the countdown timer: and &Q 1. Repeatedly press MODE until appear. (75 minutes is selected.) 2. If desired, press MIN to change the countdown to 60, 45, 30, 15 or 0 minutes. 3. If desired, press ON/OFF to turn the appliance on or off. If you turn the appliance off, the timer will turn it on after the set amount of time has passed. If you turn the appliance on, the timer will turn it off. 4. Press TIME SET to start the countdown. While counting down, flashes. Note: You can push TIME SET to switch between the countdown time and the current time. indicates the timer is in countdown timer mode.

On Mode

In On mode, the appliance is on. Press ON/ OFF to switch to Off mode to turn the appliance off. appears when the timer is on (or when you are programming an on time).

Random Mode

In Random mode, the timer randomly switches the connected appliance on and off. A random on period can range from five to 60 minutes. The timer switches the appliance on or off four to 12 random times per day.

PROGRAMMING THE TIMER

You can program the timer in Auto, On or Off modes, but the program is followed only in Auto mode. Note: Even thought the on/off light bulb symbol changes while you are programming the timer, the connected appliance does not turn on or off.
1. Press PROG to start the programming. appear if you 3UJ# 4, # # =# # , and have not set Program 1. Limited Ninety-Day Warranty Note: If you have already set Program 1, the programmed time and appear. 2. Repeatedly press DAY to scroll through the day setting options: a single day (02, 78, :(/#7+/ )5, 6$, or 68), all week (all days of week), weekdays (02# 78# :(# 7+# )5), weekends (6$ 68), or all days but Sunday (02#78#:(#7+ )5#6$). 3. Repeatedly press HOUR to select the hour. 4. Repeatedly press MIN to select the minutes. 5. Press ON/OFF to switch between programming on time and off time for the current program number. 6. Repeat Steps 24 to program the off time. 7. Press TIME SET to exit program setup. Or press PROG again to move on to 3UJ# 5, 3UJ# 6, and so on up to 3UJ# 47. Follow Steps 15 to set other programs. Note: In case of a conflict, the higher program number is followed. For example, you have programmed the timer to be on at 4 pm every day of the week and also programmed the timer to be off at 4 pm on Saturdays. In case of a conflict within a program number, Off is followed rather than On. To change the programs you have entered, scroll through the current program and change the necessary information. To clear all programs, use a straightened paper clip to press RESET. Follow Steps 16 to set new programs. Note: You will also have to reset the clock after you press RESET.
This product is warranted by RadioShack against manufacturing defects in material and workmanship under normal use for ninety (90) days from the date of purchase from RadioShack company-owned stores and authorized RadioShack franchisees and dealers. EXCEPT AS PROVIDED HEREIN, RadioShack MAKES NO EXPRESS WARRANTIES AND ANY IMPLIED WARRANTIES, INCLUDING THOSE OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED IN DURATION TO THE DURATION OF THE WRITTEN LIMITED WARRANTIES CONTAINED HEREIN. EXCEPT AS PROVIDED HEREIN, RadioShack SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO CUSTOMER OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE, LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT OR ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RadioShack HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some states do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. In the event of a product defect during the warranty period, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store. RadioShack will, at its option, unless otherwise provided by law: (a) correct the defect by product repair without charge for parts and labor; (b) replace the product with one of the same or similar design; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period. This warranty does not cover: (a) damage or failure caused by or attributable to acts of God, abuse, accident, misuse, improper or abnormal usage, failure to follow instructions, improper installation or maintenance, alteration, lightning or other incidence of excess voltage or current; (b) any repairs other than those provided by a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) cosmetic damage; (e) transportation, shipping or insurance costs; or (f) costs of product removal, installation, set-up service adjustment or reinstallation. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state. RadioShack Customer Relations, 200 Taylor Street, 6th Floor, Fort Worth, TX 76102

We Service What We Sell

02A01 61-1066

Art 880 Printed in China

43-3905 Users Guide

Caller ID Wall Phone

Thank you for purchasing your Caller ID Wall Phone from RadioShack. Please read this users guide before installing, setting up, and using your new phone.

Package contents

Caller ID Wall Phone Short Phone Cord Users Guide Long Phone Cord Coiled Cord Quick Start

Features

Caller ID memory stores information for up to 99 calls Caller ID/Call Waiting ID display shows whos calling Backlit displays for better visibility at night or in low light Traditional metal bell ringer Heavy duty design

1 Install Batteries

1. Lift the battery compartment cover from the top of the base, then remove the compartment. 2. Insert four AA batteries into the compartment as indicated by the polarity symbols (+ and ) marked inside. 3. Replace the battery compartment and cover.

b Battery Notes:

During battery replacement, keep the line cord plugged in and replace the batteries within two minutes to maintain Caller ID memory. When the low battery icon appears or the display dims, replace the batteries. Make sure the batteries fit tightly in the battery compartment. Dispose of old batteries promptly and properly. Do not burn or bury batteries. Use only fresh batteries of the required size and recommended type. Do not mix old and new batteries, different types of batteries (standard, alkaline, or rechargeable), or rechargeable batteries of different capacities. If you do not plan to use the phone for two weeks or longer, remove the batteries. Batteries can leak chemicals that can destroy electronic parts.

2 Install Your Phone

You can mount your phone on a wall plate, a wall, or place it on a desk or table. To mount the phone to a wall plate: 1. Plug one end of the supplied short modular cord into the LINE jack at the back of the base. 2. Plug the other end of the cord into the wall plate jack. 3. Align the bases keyhole slots with the wall plate studs and slide the phone downward to secure it.
To mount the phone directly on a wall: 1. Drill two holes 3.25 inches (83 mm) apart, one below the other. 2. Thread a screw into each hole, letting the heads extend about 0.2 inch (5mm) from the wall. 3. Plug one end of the supplied long modular cord into the LINE jack at the back of the base.

0.2(5mm)

3.25 (83mm)
4. Align the bases keyhole slots with the installed screws and slide the phone downward to secure it. To connect the handset, plug one end of the supplied coiled cord into the handsets modular jack. Then connect it to the jack on the left bottom of the base.

n Notes:

Your local RadioShack store sells a variety of longer coiled handset cords, which are especially useful when you mount the phone on a wall. If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this system does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer. Select a location for your telephone that is near a telephone jack and not in the way of normal activities in the area. Your telephone connects directly to a modular telephone line jack. If your telephone wiring does not have a modular jack, you can update the wiring yourself using jacks and adapters (available

3-line Display Shows name, number, date and time of incoming calls.
NEW Flashes when you have new calls. DELETE Erases Caller ID information. CALL BACK Calls back the number shown on Caller ID. UP/DOWN Scroll through Caller ID records. M/S (Master/Secondary) Set to M. TONE/PULSE Set the dial mode for your phone system. VOLUME NORM/HI Set the call volume level. RINGER OFF/LO/HIGH Set the ringer volume or turn the ringer off.
at your local RadioShack store), or have the telephone company update the wiring for you. You must use compatible modular jacks that are compliant with Part 68 of FCC Rules and the requirements adopted by the ACTA. The telephone cord and modular plug provided is Part 68 compliant for connecting to the telephone company network.

3 Set Phone Options

Phone Settings
1. Hold down both UP and DOWN for about four seconds until ENTER LANGUAGE, then ENG ESP FRA appear, with ENG flashing. 2. Press UP or DOWN to select the desired language, then press DELETE to confirm. LCD CONTRAST and 5 appear on the display, with 3 flashing. 3. Press UP or DOWN to select the contrast level (1-5), and press DELETE to confirm. ENTER AREA CODE appears, then _ _ _ appears, with the first _ flashing. 4. Press UP or DOWN to select the first number of the area code, and press DELETE to confirm the selection. The flashing _ goes to the next digit. 5. Repeat step 4 to set the second and third digits.

Ringer

If you do not want to hear the phone ring, slide RINGER to OFF. You can still make calls with the ringer off, and you can still answer calls if you hear another phone on the same line ring. If you want to hear the phone ring, set RINGER to HI or LO.

Dial Mode

Slide TONE/PULSE to the setting for the type of dialing service you have. If you are not sure which type you have, do this simple test. 1. Slide TONE/PULSE to TONE. Lift the handset and listen for a dial tone. 2. Press any number except 0. (If your setup requires that you dial an access code, usually 9, before you dial an outside number, do not press the access code number.) If the dial tone stops, you have touchtone service. Keep the switch on TONE. If the dial tone continues, you have pulse service. Set the switch to PULSE.
Using Special Tone Services
Some computer services require tone signals for communications. If you have pulse service, you can still simulate tone signals by following these steps. 1. Connect to the special service using pulse dialing. 2. When the special service answers, press * to temporarily switch to tone dialing. 3. When you complete the call, hang up to change the setting back to PULSE.

Master/Secondary Setting

For modern phones systems, slide M/S to M.
If you have other phones with a Master/Secondary switch, set them to S. Set one system to answer and set the others to off. If M is not set on at least one phone, incoming calls might be disconnected.

Do not connect more than four Caller ID modules (including this phone) that do not have Call Waiting to the same phone line. If you connect another type of Caller ID module that has Call Waiting to the same phone line as your system, the Call Waiting signal might be garbled or not received.

Operation

Making a Call
1. Pick up the handset and wait for a dial tone. 2. Use the keypad to enter the number you wish to dial. The number appears on the display. 3. When you complete your call, hang up the handset. A few seconds later, the number disappears, and the display returns to normal.
n Note: If you dial a number over 15 digits, only the last 14
digits appear on the display.

Receiving a Call

When you receive a call, the phone rings and the NEW indicator flashes. CALL# and the callers number appear on the display. To answer the call, pick up the handset.
This phone is designed with a clock timer to count the offhook time in seconds, up to one hour. The timer appears on the display and starts to count up when you dial a number or answer an incoming call.
n Note: Ifstartslift the handset and10dont dial a number, the timer you appears and to count up after seconds.

Using Flash

If you have Call Waiting, press FLASH to answer an incoming call without disconnecting the current call. Press FLASH again to return to the first call.
n Note: the current call. Call Waiting, pressing FLASH might If you do not have disconnect

Using Redial

To redial the last number you called, pick up the handset and press REDIAL when you hear a dial tone. The number scrolls across the display, and the phone automatically dials it.
n distance asredialasmemory holdsnumbers. digits, so you can redial Note: The up to 32 long well local phone

Using Pause

Some telephone systems require you to dial an access code (usually 9) and wait for a second dial tone before dialing an outside number. When you manually dial a number, you can have your telephone pause anywhere during the dialing sequence. Simply press PAUSE at the desired location. When you redial a number, the telephone pauses for about four seconds at the pause entry. For longer pauses, press PAUSE again.

Caller ID Operation

If you subscribe to a Caller ID service, the phone automatically displays information about calls you receive and stores the information in Caller ID memory. The system can store up to 99 incoming phone numbers or 64 incoming phone numbers with names into call records.
During an incoming call, the phone company automatically sends the correct time between the first and second rings to update your systems display.

Review Call Records

Press UP or DOWN to review the new calls. After all new calls have been reviewed, END OF NEW CALL appears. To review all the records from oldest to newest, press UP. To review the records from newest to oldest, press DOWN. After reviewing all records in memory, END OF LIST appears. If an incorrect, invalid, or incomplete Caller ID signal is received, LINE ERROR appears on the display. If the name and number are not available due to the callers restriction, PRIVATE CALL appears on the display. If the name and number are not available, --UNAVAILABLE-- appears on the display. RPT appears with a number if you have received a call from the same phone number more than once. If you do not press a button within about 15 seconds, the system automatically returns to the normal display.

The NEW indicator remains flashing until you have reviewed all new calls. The number of new calls does not change until all calls have been reviewed and END OF NEW CALL appears. The new call counter then resets to 0.
Call Back from Caller ID Memory
1. Press UP or DOWN to find the number to call back. 2. Press CALL BACK twice. LIFT HANDSET or PICK UP CALL appears.
3. Lift the handset, and the number is redialed automatically. Follow these steps to select one of the options for Caller ID call back. 1. Press UP or DOWN to find the Caller ID memory location to be redialed. 2. Press CALL BACK. The 7- or 11-digit number flashes. 3. Press UP or DOWN to select one of the four options. Option + Area Code + 7-digit number (11 digits) Option 2 1+7-digit number (8 digits) Option 3 Area Code + 7-digit number (10 digits) Option 4 7-digit number 4. Press CALL BACK again to confirm. 5. Pick up the handset, and the selected number is dialed automatically.

Delete Call Records

You can select and delete an individual call record, or all call records stored in the system. To delete a single call record, press UP or DOWN until the call record you want to delete appears. Press DELETE twice. The call record is deleted, and the system automatically renumbers the remaining call records. To delete all call records after all new calls have been reviewed, hold down DELETE for about three seconds. ERASE ALL CALLS appears. Press DELETE. The system deletes all call records. NO CALLS appears, and then TOTAL: 00 NEW: 00 appears.
When the phones memory is full, it automatically replaces the oldest call record with the newest incoming call. 11
If you do not press any button within about 15 seconds while ERASE ALL CALLS appears on the display, the phone automatically returns to normal display and the records are not deleted.

Additional Information

Important Safety Information
When using your telephone equipment, basic safety precautions should always be followed to reduce the risk of fire, electric shock and injury to persons, including the following: Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink or laundry tub, in a wet basement or near a swimming pool. Avoid using a telephone (other than a cordless type) during an electrical storm. There may be a remote risk of electric shock from lightning. Do not use the telephone to report a gas leak in the vicinity of the leak. Handle the phone carefully. Do not drop it. Do not use or store the phone in extreme temperatures.

Service and Repair

If your telephone is not performing as it should, take it to your local RadioShack store for assistance. To locate your nearest RadioShack, use the store locator feature on Radioshacks website (www.radioshack.com), or call 1-800-THE SHACK (8437422) and follow the menu options. Modifying or tampering with the telephones internal components can cause a malfunction and might invalidate its warranty and void your FCC authorization to operate it.

Surge Protection

Your telephone has built-in protection circuits to reduce the risk of damage from surges in telephone line and power line current. These protection circuits meet or exceed the FCC requirements. However, lightning striking the telephone or power lines can damage your telephone. Lightning damage is not common. Nevertheless, if you live in an area that has severe electrical storms, we suggest that you unplug your phone when storms approach to reduce the possibility of damage.

FCC Information

FCC Part 15 This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult your local RadioShack store or an experienced radio/TV technician for help. If you cannot eliminate the interference, the FCC requires that you stop using your equipment. Changes or modifications not expressly approved by RadioShack may cause interference and void the users authority to operate the equipment. This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. FCC Part 68 and ACTA a) This phone complies with Part 68 of the FCC rules and the requirements adopted by the ACTA. On the bottom of this equipment is a label that contains, among other information, a product identifier in the format US:AAAEQ##TXXXX. If requested, this number must be provided to the telephone company. b) The registration jack USOC for the equipment is RJ11C or RJ11W. c) This equipment is designed to be connected to the telephone network or premises wiring using a compatible modular jack which is Part 68 compliant. A compliant telephone cord and modular plug is provided with this product. See installation instructions for details. d) The REN is useful to determine the quantity of devices that may be connected to the telephone line. Excessive RENs on the telephone line may result in the devices not ringing in response to a n incoming call. In most, but not all areas, the sum of RENs of all devices should not exceed five (5). To be certain of the number of devices that may be connected to a line, as determined by the total RENs, contact the local telephone company. e) If this phone causes harm to the telephone network, the telephone company will notify you in advance that temporary discontinuance of service may be required. But if advance notice isnt practical, the telephone company will notify the customer will be notified as soon as possible. You will be advised of your right to file a complaint with the FCC if you believe it is necessary. f) Your telephone company may make changes in its facilities, equipment, operations, or procedures that could affect the operation of your equipment. If they do, you will be given advance notice so as to give you an opportunity to maintain uninterrupted service.

g) If you experience trouble with this phone, please contact your service provider for repair/warranty information. If your equipment is causing harm to the telephone network, the telephone company may request that you disconnect the equipment until the problem is resolved. h) No repair can be done to this equipment. i) Connection to party line service is subject to state tariffs. Contact the state public utility commission, public service commission or corporation commission for information. j) If your home has specially wired alarm equipment connected to the telephone line, ensure the installation of this phone does not disable your alarm equipment. If you have questions about what will disable alarm equipment, consult your telephone company or a qualified installer.
k) This phone is hearing aid compatible.

Limited Warranty

RadioShack warrants this product against defects in materials and workmanship under normal use by the original purchaser for one (1) year after the date of purchase from a RadioShack-owned store or an authorized RadioShack franchisee or dealer. RADIOSHACK MAKES NO OTHER EXPRESS WARRANTIES. This warranty does not cover: (a) damage or failure caused by or attributable to abuse, misuse, failure to follow instructions, improper installation or maintenance, alteration, accident, Acts of God (such as floods or lightning), or excess voltage or current; (b) improper or incorrectly performed repairs by persons who are not a RadioShack Authorized Service Facility; (c) consumables such as fuses or batteries; (d) ordinary wear and tear or cosmetic damage; (e) transportation, shipping or insurance costs; (f) costs of product removal, installation, set-up service, adjustment or reinstallation; and (g) claims by persons other than the original purchaser. Should a problem occur that is covered by this warranty, take the product and the RadioShack sales receipt as proof of purchase date to any RadioShack store in the U.S. RadioShack will, at its option, unless otherwise provided by law: (a) repair the product without charge for parts and labor; (b) replace the product with the same or a comparable product; or (c) refund the purchase price. All replaced parts and products, and products on which a refund is made, become the property of RadioShack. New or reconditioned parts and products may be used in the performance of warranty service. Repaired or replaced parts and products are warranted for the remainder of the original warranty period. You will be charged for repair or replacement of the product made after the expiration of the warranty period. RADIOSHACK EXPRESSLY DISCLAIMS ALL WARRANTIES AND CONDITIONS NOT STATED IN THIS LIMITED WARRANTY. ANY IMPLIED WARRANTIES THAT MAY BE IMPOSED BY LAW, INCLUDING THE IMPLIED WARRANTY OF MERCHANTABILITY AND, IF APPLICABLE, THE IMPLIED WARRANTY OF FITNESS FOR A PARTICULAR PURPOSE, SHALL EXPIRE ON THE EXPIRATION OF THE STATED WARRANTY PERIOD. EXCEPT AS DESCRIBED ABOVE, RADIOSHACK SHALL HAVE NO LIABILITY OR RESPONSIBILITY TO THE PURCHASER OF THE PRODUCT OR ANY OTHER PERSON OR ENTITY WITH RESPECT TO ANY LIABILITY, LOSS OR DAMAGE CAUSED DIRECTLY OR INDIRECTLY BY USE OR PERFORMANCE OF THE PRODUCT OR ARISING OUT OF ANY BREACH OF THIS WARRANTY, INCLUDING, BUT NOT LIMITED TO, ANY DAMAGES RESULTING FROM INCONVENIENCE AND ANY LOSS OF TIME, DATA, PROPERTY, REVENUE, OR PROFIT AND ANY INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES, EVEN IF RADIOSHACK HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES. Some States do not allow limitations on how long an implied warranty lasts or the exclusion or limitation of incidental or consequential damages, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from State to State. You may contact RadioShack at: RadioShack Customer Relations, 300 RadioShack Circle, Fort Worth, TX 76102 04/08

www.RadioShack.com

Protect the environment by recyling used electronics. Go to E-CyclingCentral.com to find an electronic recycling center near you. 2009. RadioShack Corporation. All rights reserved. RadioShack and RadioShack.com are trademarks used by RadioShack Corporation.

Printed in China

11A09 43-3905 4LM053Y2