The following points should also be noted; t Genuine Raytheon cables should be used at all times. Cutting and rejoining these cables can compromise EMC performance and so should be avoided unless doing so is detailed in the installation manual. Raytheon equipment should be serviced only by authorised Raytheon service engineers. They will ensure that service procedures and replacement parts used will not affect EMC performance. There are no user serviceable parts in any Raytheon product. Voltage drops below 10v in the power supply to our products can cause the equipment to reset. This will not damage the equipment but will cause the loss of some information and can change the operating mode. This most frequently happens during engine starting, and so to reduce the risk of this occurring, it is recommended that the equipment is supplied from a different battery than the one used for engine start. Some products generate high voltages, and so never handle the cables/ connectors when power is being supplied to the equipment. Always check the installation before going to sea to make sure that it is not affected by radio transmissions, engine starting etc. In some installations, it may not be possible to prevent the equipment from being affected by external influences. In general this will not damage the equipment but can lead to it resetting, or momentarily result in faulty operation.
Please keep these notes for future reference.

Chapter 2: Installation

This chapter covers installation of the support bracket and external cable of the GPS11. If the unit is to be used purely as a standalone handheld GPS then this chapter may be ignored.
2.1 Velcro Strap mounting
The unit is supplied with a Velcro strip which may be attached to the rear case using the lanyard slots. Ensure that the strap is pulled tight and the end tabs turned back and secured to the main strap. Attach the fixing strip to the desired surface using glue or double sided tape or sew the strip onto clothing.
2.2 Bracket Mounting ( GPS11 plus only)
The unit is supplied with a universal mounting bracket (selected models only) which will allow your GPS to be slotted into a permanent storage/operating position.
2.2.1 Fixed to a vertical bulkhead
Select your desired position and screw the backplate (1) to the vertical bulkhead. Slot the main bracket (2) onto the top tab of the backplate and then push the bottom of the main bracket back, to allow the supplied finger bolt (3) to secure the base of the bracket.

D4117-1

2.2.2 Fixed to a horizontal surface
The bracket may be fixed such that it may be adjusted vertically only or such that it may be rotated and adjusted vertically. For vertical adjustment only screw the backplate (1) to the desired horizontal surface and then secure the main bracket (2) at the desired angle using the finger bolt (3).

D4116-1

To allow the bracket to be rotated assemble the backplate (1) to the main bracket (2) using the finger bolt (3). The angle may be adjusted later if required. Select your desired position and screw the base plate (4) to the horizontal surface, then attach the backplate to the baseplate using the finger bolt (5).

D4118-1

2.2.3 Fixed to a rail
The bracket may be mounted to a rail using the same method as for mounting to a horizontal surface but by reversing the base plate and using stainless steel nuts and bolts (not supplied) to clamp the base plate to the back plate around the rail.

D4119-1

2.3 Accessories Carry Case
Part No. P36003 A soft carry case is available to protect your GPS11 unit.

Bracket Assembly

Part No. P36004 (included in GPS11 plus) To allow the standard GPS11 unit to be bracket mounted the bracket assembly that is included in the GPS11 plus kit is available separately.

External Connection

There are three external cable accessories available which may be used to connect your GPS11 to external power and data sources. Part No. P36001 Power and Data Cable (included in GPS11 plus)

D4124-1

Part No. P36005 Power and Data Cable + PC Connector

D4126-1

Ensure that any unused cores are isolated to prevent data loss Part No. P36002 Power Cable with Cigar Lighter Adapter

D4125-1

2.4 External Power connection
The GPS11 may be connected to an external power supply between 10V and 24V d.c. Connection is made via any of the Power/Data cables shown on page 13 and should be protected by a 5 Amp fuse or circuit breaker.
Red Blue 3 Red 5 Amp Blue 5 6

10V - 32V d.c.

D4121-1
2.5 External Data Connection
The GPS11 is capable of outputing data to other navigational instrumentation or accepting waypoint information from an external source (P.C.). Connection is made via the supplied Power/Data cable.
Data communications protocols must be set up correctly in the SET-UP PORT section, see page xx.
Chapter 3: Getting Started
3.1 Inserting the batteries
Open the battery cover on the base of the unit by pulling the compartment latch (1) towards the side of the unit. The battery cover will spring open revealing the black battery carrier within. Remove the carrier and insert the four AA size batteries following the + and - marks. Insert the loaded carrier back into the unit taking care to line up the stud (2) on the carrier with the mark on the cover seal (3). Close the battery cover and pull the latch toward the side of the unit. The cover will click into position sealing the battery compartment. Note: The cover will not close if the battery carrier has been inserted incorrectly.

D4120-1

Apelco GPS 11 Installation and Operation Handbook
3.2 Switching the unit ON and OFF
Press the PWR button to switch on your GPS11. The Startup screen will be displayed for 5 seconds.

startup

After 5 seconds the GPS satellite information page will be displayed showing the number and identification of the satellites being received.

satstat

To switch off your GPS11 press and hold down the PWR button. After a one second delay a countdown display will appear. Keep the PWR button held down for a further three seconds until the display switches off.

3.3 Light and Contrast

After startup the illumination and contrast may be adjusted by pressing the PWR button momentarily.

lgtcon

Use the trackpad up/down arrows to highlight BACKLIGHT, CONTRAST or BACKLIGHT TIME and press ENTER to select. BACKLIGHT: CONTRAST: Use the up/down arrows to select ON or OFF then ENTER to store. Use the left/right arrows to increase or decrease the contrast to the desired level then ENTER to store.
BACKLIGHT TIME: Use the up/down arrows to select the option required then ENTER to store. Options are: 15 or 30 seconds 1, 2 or 4 minutes Continuous Press PAGE to return to the last screen. Note: The backlight will reduce the battery life. The continuous setting is not recommended unless the unit is connected to an external power supply.
3.4 Selecting different pages
Use of the PAGE button allows the unit to move through the sequence of main operating pages:
> SATELLITES < > POSITION < > WAYPOINT DATA < > ROUTE DATA < > PLOTTER <
Each page has a menu bar near the bottom of the display. To access a menu use the left/right arrows on the trackpad to highlight the appropriate title and then press ENTER to activate the menu.

3.5 Status indicator

The bottom line of the screen shows the units current status and cycles though three sets of information: Battery Status:

Full Half Low

Number of Satellites being tracked: Chart Datum selected: Position Fix: Illumination: Operating Mode: Differential Fix:

3.6 Setup

Basic Setup of the GPS11 unit is accessed by highlighting SETUP? on the menu bar on the SATELLITES page. The Setup section is then divided into four sub-menus: SET-UP SYSTEM SET-UP PLOTTER SET-UP NAVIGAT SET-UP PORT Sub menus are accessed by highlighting the appropriate line and pressing ENTER. After switching on select SETUP? on the menu bar using the trackpad. Press ENTER to display the main menu.

Mainmen1

Set-up System
Use the trackpad to select SET-UP SYSTEM and press ENTER.

Setsys

Use the trackpad to highlight the desired option:

D/S UNIT:

Press ENTER to select the desired units for Speed and Distance. Highlight the desired option and press ENTER to select. Options are: KM - KPH, NM - KT, MI - MPH.

ALT. UNITS:

Press ENTER to select the desired units for altitude. Highlight the desired option and press ENTER to select. Options are: METRE, FEET,

ALTITUDE:

Press ENTER to select whether to display or not the altitude information on the Position page. Options are: ON -display altitude / OFF - not display altitude

WARM START

Press ENTER to select a start area: AUTO - The unit will search for all satellites and will initiate a cold start if the unit has moved location while switched off. Selection - A local area may be selected instructing the unit to search for selected satellites first. Note: When the unit is first switched on the setting of the correct Warm Start region will greatly reduce the time to first fix. The auto setting could result in a time to first fix in excess of 30 minutes.

LOCAL TIME

Press ENTER to select a time offset from UTC. Use the trackpad to input the correct local time difference for the area you are in and press ENTER to select.

ECONOMY MODE

Stops GPS reception to increase the battery life of the unit. Use this setting for entering waypoint and route information whilst the unit is not being used for navigation. Options are: Note: ACTIVE - reception disabled NOT ACTIVE - reception enabled
Setting is returned to NOT ACTIVE on power up.

MAIN MENU?

Highlight this option and press ENTER to return to the main menu.

Set-up Plotter

Use the trackpad to select SET-UP PLOTTER and press ENTER.

Setplot

CLEAR TRACK:
Press ENTER to clear the displays track. A confirmation page will appear. Press ENTER once more to clear the stored track information from the memory.

RESET TRIP LOG:

Press ENTER to reset the displayed Trip Log. A confirmation page will appear. Press ENTER once more to reset the trip log or use the trackpad to highlight NO? and then press ENTER to cancel.

TRACK INTERVAL:

Press ENTER to select the time between track data saves. Options are: 5 seconds 30 seconds 1 minute 2 minutes 5 minutes
The longer the time interval the larger is the track that can be stored although the resolution of the final plot may be poor if the distances travelled are small.

RANGE RINGS:

Press ENTER to switch the range rings ON or OFF.

WPT DISPLAY:

The symbol which displays a waypoint on the plotter screen may be set either to (O) or to the first letter of the waypoint name. Press ENTER to select the desired option.

Set-up Navigation

Use the trackpad to select SET-UP NAVIGAT and press ENTER.

Setnav

MAP DATUM:
The default map datum is WGS84, however it is possible to select from a list of alternative datums as specified in Appendix A of this manual. Highlight the required datum using the trackpad and press ENTER to select. Note: It is important to ensure the correct datum is selected to prevent position errors being introduced.

ANTENNA MODE:

For Marine use select the 2 DIMENSIONAL mode and enter the antenna height above sea level to obtain the most accurate position. For land use select 3 DIMENSIONAL mode and allow the GPS unit to calculate height above sea level. Setting the mode to AUTO will cause the GPS to use 3 dimensional mode when it is tracking 4 or more satellites.

ALTITUDE

If the antenna mode is set to 2 dimensional operation the unit must be told at what height above sea level it is. This will ensure the positional accuracy is maintained. If 3 dimensional operation is selected then altitude need not be entered.

COORDINATES

Position and waypoint information may be displayed in any one of several systems. Options are: 000000.00, OSGB, UTM, Swedish Grid
COMPASS VARIAT (Variation)
Compass bearings may be displayed in Magnetic or True form. If set to 0000 then all bearings displayed will be displayed as True bearing. This unit does not apply variation automatically.
Set-up Communications Port
Use the trackpad to select SET-UP PORT and press ENTER.

Setport

SERIAL OUTPUT:
Options are: NMEA182, NMEA183, WAYPOINT (for PC waypoint communication)

SERIAL INPUT:

Options are: DIFFERENTIAL (for differential receiver input), WAYPOINT (for PC waypoint communication)
Note: Specifications of the NMEA sentences are given in Appendix B of this manual.

3.7 Marking Events

Pressing the EVENT button on the GPS11 enters the current position into the memory as a waypoint. The display will show the position information.
Time and date of EVENT automatically entered as a comment

Event01

The event is automatically given the name WPT XXX where XXX is the next available number. Highlighting SAVE on the menu bar will save the Event as a waypoint which will appear in the waypoint list (see page 34). It is possible to edit any of the Event data by using the trackpad to highlight the relevant piece of information and pressing the ENTER button. It is also possible to save the information as shown and edit later using the Modify Waypoint facility described on page 34).

3.8 Man Over Board (MOB)

Should a crewmember fall overboard press and hold the EVENT button for 2 seconds. The GPS11 will immediately enter the Plotter screen set to the minimum range. The range will automatically alter to ensure that the MOB position and your current position remain on the display at all times.
Use the Bearing and Range figures to steer the vessel back to the original position to recover the casualty. Pressing ENTER will cancel the MOB mode and return to the normal plotter page. Use the PAGE button to continue using the GPS unit normally.

Chapter 4: Operation

4.1 Satellites Page
The satellites page shows the status and numbers of satellites being tracked by the GPS11. The main page shows the satellite numbers and the signal strength.

satel01

By highlighting DET? on the menu bar and pressing the ENTER button details of azimuth and elevation of the satellites may be viewed.

satel02

By highlighting DIF? on the menu bar and pressing the ENTER button details regarding a differential fix may be viewed.

difinfo

RECEPTION QUALITY
The bargraph shows the reception quality with a full bar indicating 100% reception

DGPS STATION

The identification number of the differential station being received will appear automatically.

CORRECTED SATS

The satellites which are being corrected by the differential station will be indicated by their identification numbers.

4.2 Position Page

This page gives your primary position information along with speed and course over the ground.
There are no menu options on this page.

4.3 Waypoint Data Page

This page gives your primary waypoint information. Use this page for entering, deleting or editing waypoint information and activating a waypoint.

wayp01

There are three menu options ACTI?, EDIT? and DISP? Highlighting DISP? on the menu bar will allow the choice of Data, CDI or BDI display.

Waypoint Display Page

From the main waypoint page highlight the DISP? option and press ENTER you will be presented with three options: Data CDI Shows the main waypoint information page Shows the Course Direction Indicator Page Active waypoint information
Shows the Bearing Direction Indicator Page
Entering, Modifying and Deleting Waypoints
From the main Waypoint information page select the menu option EDIT? and press the ENTER button. The menu changes to allow three options ENTER?, MODIFY? and DELETE?

edit01

Entering a Waypoint
Select ENTER? on the menu bar and press the ENTER button. A blank waypoint data page will appear.

editwp

The highlighted setting is WPT:, press ENTER to select the waypoint name option.

wptname

Use the trackpad up and down arrows to select the first letter or number of your waypoint name then use the right arrow to move on to the next digit. Continue until the waypoint name is complete (max. 6 digits) and press ENTER. Use the down arrow to highlight LATITUDE: and press ENTER.
Use the up and down arrows to select the digits and the right and left arrows to move around until the correct waypoint latitude has been entered. Press the ENTER button. Use the down arrow to highlight LONGITUDE? and press ENTER.
Repeat the above procedure to enter the correct waypoint longitude.
Use the down arrow to highlight COMMENT: and press ENTER.

comment

If desired a 20 digit comment may be added to assist later in identifying the waypoint, select letters and numbers as before and press ENTER to complete the waypoint information.

wptcompl

Check the data entered carefully and, with the VALID? setting highlight on the menu press ENTER to save the information. Note: Failure to highlight VALID? in the menu bar and press the ENTER button will cause the waypoint information to be lost. If the information is incorrect you may use the trackpad arrows to go back and highlight the setting to be changed or highlight CLEAR? on the menu bar to clear the form and start again.

Modifying a Waypoint

Select MODIFY? on the menu bar and press the ENTER button. A list of stored waypoints will appear.

wptlst01

Use the trackpad down arrow to highlight the required waypoint. Latitude, Longitude and comments will appear for each waypoint as the list is advanced. Press ENTER when the desired waypoint is located.
Use the trackpad to navigate around the screen and enter the modifications required. Highlight VALID? and press ENTER to store the changes or highlight ERASE? and press ENTER to clear the waypoint data and start again.

Deleting a Waypoint

Select DELETE? on the menu bar and press the ENTER button. A list of stored waypoints will appear.
Use the trackpad down arrow to highlight the required waypoint. Lat/ Lon and comments will appear for each waypoint as the list is advanced. Press ENTER when the desired waypoint is located.

delwrn1

Press ENTER once more to confirm waypoint deletion or press PAGE to return to the main Waypoint information page. Note: If the waypoint is used in a route then an error message will appear giving the name of the route in which the waypoint is used. The route must be edited to remove the waypoint before the waypoint can be deleted from the waypoint list.

Activating a Waypoint

To start the GPS11 tracking to a waypoint highlight ACTI? on the menu bar and press ENTER.

actwpt01

You now have the option to select a waypoint from the stored list or to enter a new waypoint.
Activating a Waypoint from the list
Highlight LIST? on the menu bar and press ENTER. A list of stored waypoints will appear.
Activating a new Waypoint
Highlight NEW? on the menu bar and press the ENTER button. A blank waypoint data page will appear.
Follow the procedure on page 31 Entering a Waypoint to complete the form. Check the data entered carefully and, with the VALID? setting highlighted on the menu press ENTER to save the information. Note: The new waypoint will be stored in memory and added to the waypoint list. If the information is incorrect you may use the trackpad arrows to go back and highlight the setting to be changed or highlight CLEAR? on the menu bar to clear the form and start again To stop tracking to a waypoint highlight ACTI? on the menu bar and press ENTER. DEACTIVATE? will be highlight on the menu bar. Press ENTER, a warning page will be displayed.

stopwarn

Press ENTER to stop tracking to that waypoint.

4.4 Route Data Page

This page gives your primary route information. Use this page for entering, deleting or editing route information and activating a stored route.

route01

There are three menu options ACTI?, EDIT? and DISP?
Highlighting DISP? on the menu bar will allow the choice of Data, CDI or BDI displays as indicated on page 30 Waypoint Display Page.

Editing a route

Highlight EDIT? from the menu bar and press ENTER. Three options are given: ENTER?, MODIFY? and DELETE?

Entering a Route

Select ENTER? on the menu bar and press the ENTER button. A blank Route data page will appear.

edit02

The highlighted setting is RTE:, press ENTER to select the Route number option.

rtename

Use the trackpad arrows to select the number (00 to 19) of the new route and press ENTER. If the route number has already been used, the previously entered route information will be displayed whereas if the route is new the data sheet will be empty. Use the down arrow to highlight the first waypoint line and press ENTER.

rtewpt01

Use the trackpad to enter the desired waypoint name. As you enter the individual numbers or letters the first matching entry in the waypoint library will be displayed. This allows you to select a waypoint without having to enter the complete name. Press ENTER when the correct waypoint is being displayed to enter the waypoint into the route.

rtewp02

Press the down arrow to highlight the next waypoint data line and repeat the above procedure. Continue until the route is complete (maximum 20 waypoints). Check carefully to ensure the route information is correct and highlight VALID? on the menu bar and press ENTER. Note: Failure to highlight VALID? in the menu bar and press the ENTER button will cause the waypoint information to be lost.

Modifying a Route

Select MODIFY? on the menu bar and press the ENTER button. The Route list page will appear.

rtelst

Highlight the route to be modified and press ENTER. The route data page will be displayed.

modrte

Use the trackpad arrows to highlight the waypoint line that requires changing and press ENTER. Select the correct waypoint from the list and press ENTER to update the route. Check the changes carefully , highlight VALID? on the menu bar and press ENTER to store the modified route.

Deleting a Route

Select DELETE? on the menu bar and press the ENTER button. The Route list page will appear.
Highlight the route to be deleted and press ENTER. A warning message will be displayed asking for confirmation that the route should be deleted.

rtedelcn

Press ENTER to confirm deletion or PAGE to return to the main Route Data page.

Activating a Route

From the main Route Data page highlight ACTI? on the menu bar and press ENTER.

actrte01

Activating a Route from the list
Highlight LIST? on the menu bar and press ENTER. A list of stored routes will appear.

rtelst1

Use the trackpad down arrow to highlight the required route and press ENTER.
You will be asked to select the direction in which you wish to follow the selected route.

rtedir

Select Forward or Reverse and press ENTER. You will now be asked to select your start waypoint. The first waypoint of the stored route will be displayed.

rtestart

If you wish to commence the route from an alternative waypoint use the trackpad up and down arrows to select the desired starting point. Press ENTER when the desired start point is displayed. The selected Routes data page will be displayed.

rtedata1

The GPS11 will start tracking through the selected route.

5.2 How to Contact Apelco In the USA.
For technical Support Please call 1-800-539-5539, extension 2445 or (603) 647-7530, extension 2445. Our Fax number is 1-603-634-4756. You may reach our Technical Service Department Monday through Friday, 8:15 A.M. to 5:00 P.M. EasternStandard Time or Daylight Saving Time. Our Technical Support Specialists are available to answer questions about installing, operating, and troubleshooting about your Apelco unit. You may also reach our Technical Support Department via the Internet. Questions may be addressed directly to: rmc_tech_apelco@raymarine.com Or, you may visit Apelco at the World Wide Web site for Raytheon Electronics: www.raymarine.com
For accessories and parts Please call 1-800-539-5539, extension 2120 or (603) 647-7530, extension 2120. Our Customer Service Department is available Monday through Friday 8:15 A.M.to 5:00 P.M. Eastern Time. Please have the Apelco part number ready when placing an order. (See the optional Accessory List in this manual on page 12.) If you are not sure which item you need for your Apelco unit, please contact our Technical Support Department before placing your order. Apelco accessory items and parts are also available through your authorised Apelco dealer. For product repair and service When you first receive your unit, please be sure to complete and mail the warranty card included in the package. In the unlikely event your Apelco unit should develop a problem, please return the unit to our Product Repair Centre. If you need service help, and you have not mailed your warranty card, please include a copy of your original purchase receipt to verify your warranty status. Please return your unit to this address: Apelco Product Repair Center 676 Island Pond Road Manchester, NH. 03109-5420

In Europe

Contact your Apelco main distributor for assistance for the supply of accessories and technical assistance. Faulty units may also be returned to the distributor or returned directly to: Raytheon Marine Europe Ltd. Robinson Way Anchorage Park Portsmouth, PO3 5TD England The telephone number for Raytheon Marine Europe is (44) 1705 693611. The Fax number is (44) Contact via the Internet: Questions may be addressed directly to: techsupap@rmeltd.co.uk Or, you may visit Apelco at the World Wide Web site for Raytheon Electronics: www.raymarine.com.

5.3 Maintenance

Chemical and abrasive materials must not be used to clean the GPS11 housing; if it is dirty, clean it with a soft, damp cloth. Examine all cables for chafing or damage to the outer shield and, where necessary, replace with genuine Apelco cables and resecure. Ensure that any external plugs and sockets are kept clean and dry. Use small amounts of a silicon based grease to prevent corrosion on exposed connectors.

Chapter 6: Specification

Dimensions
Size: Weight: 51 x 150 x 33 mm 2.01 x 5.90 x 1.30 255g ( 9 oz.) with batteries

LCD Display:

100 x 64 FSTN with EL back light.

Receiver

Frequency: Type: Antenna: Maximum Speed: 3 Dimensions: Pos. Rate Update: 1.575 GHz, C/A code. 8 genuine parallel channels with phase tracking (predicts the next 4 in view). Patch internal / integrated antenna 2000km/hour Latitude, Longitude and Altitude; requires 4 or more satellates 1 second
Automatic Selection of Satellites Automatic Almanac update Autolocalization

Accuracy

Horizontal Position: with SA code : 100m RMS (2D) in RTCM 104 differential mode : 2 to 5 m RMS. Velocity: Acceleration: with SA code : 1.0km/hour RMS in differential mode : 0.1 km/hour 3g
Time to First Fix (typical)
Reaquisition: Up to 1 hour off: Up to 24 hours off: Worldwide cold start: 4 seconds 30 seconds 90 seconds 3 minutes

Power Supply

Batteries: External Supply: Battery Life: 4 AA alkaline batteries 10-32v dc 8 hrs in continuous permanent mode. 10 hrs in economy permanent mode. 16 hrs in discontiouous mode with a use equivalent to one hour per day.

Temperature

Operating: Storage: -100 to +600C (140 to 1400F) -200C to +700C (-40 to 1580F)
Output: Input: NMEA0182, and 0183. NMEA 0183, RTCM 104. Waypoint loading and unloading with P.C.

Plotter Functions

Plotter Capacity: Plotter time scale: Plotter scales: 300 points 25 hours max. 0.02 to 250 in the units selected
Display of waypoints and active route plan.

Main Functions

Chart Datums: Coordinates: Navigation: Waypoints: As shown in Appendix A of this manual. latitude, longitude, UTM, OSGB, Swedish Grid Speed and Course over the Ground. 600 waypoints each with 6 alphanumerical character display and automatic classification. Event mark including 20 reversible routes of 20 wayponts maximum. Range and bearing to a selected waypoint. Total distance covered log.

Other features:

Appendix A : Reference Ellipsoids and Datum Table
Appendix A : Chart Datums
Code Name WGS 84 Adinan - MEAN FOR Ethiopia, Sudan Adinan - Burkina Faso Adindan - Cameroon Adindan - Etiopia Adindan - Mali Adindan - Senegal Adindan - Sudan Afgooye - Somalia Ain el Abd 1970 - Bahrain Ain el Abd 1970 - Saudi Arabia Anna 1 Astro 1965 - Cocos Islands Antiguaa Island Astro 1943 Antigua (Leeward Islands) Arc 1950 MEAN FOR Botswana, Lethoso, Malawi, Swaziland, Zaire, Zambia, Zimbabwe Arc 1950 - Botswana Arc 1950 - Burundi Arc 1950 - Lethoso Arc 1950 - Malawi Arc 1950 - Swaziland Arc 1950 - Zaire Arc 1950 - Zambia Arc 1950 - Zimbabwe Arc 1960 - MEAN FOR Kenya, Tanzania Ascension Island 1958 Abbrev 11 WGS84 ADINES ADINBUR ADINETH ADINSEN ADINSUD AINBAH AINSAUD ANT1943 ARC1950 Abbrev 23 WGS84DEFAULT ADINANMEANS ADINANBURKIN ADINANETHIOP ADINANSENEG ADINANSUDAN AIN1970BAHR AIN1970SAUDI ANTIGUAIS1943 ARC1950MEAN

CAMERN MINNACAMEROON NIGERIA MINNACAMEROON MONSERT MONTSERIS1958 GABON OMAN UAE TR&TOB NAMER1 MPORALOKOGAB NAHRWANOMAN1 NAHRWANUEA3 NAPARIMABWI NAMER19271

SAUDIAR NAHRWANSAUDI2

North American 1927 NAMER2 MEAN FOR Belize, Costa Rica, El Salvador, Guatemala, Honduras, Nicaragua North American 1927 - MEAN FOR Canada NAMER3 North American 1927 MEAN FOR CONUS NAMER4

NAMER19272

NAMER19273 NAMER19274 NAMER19275
North American 1927 NAMER5 MEAN FOR CONUS (East Mississippi River) including Louisiana, Missouri, Minesota North American 1927 MEAN FOR CONUS (West of Mississippi River) North American 1927 - Alaska North Amerian 1927 Bahamas (Acdept San Salvador Island) North American 1927 Bahamas (San Salvador Island) North American 1927 Canada (Alberta, British Columbia) North Ameria 1927 Canada (Manitoba, Ontario) NAMER6

NAMER19276

NAMER7 NAMER8 NAMIR9
NAMER19277 NAMER19278 NAMER19279
NAMIR10 NAMER192710 NAMIR11 NAMER192711
North America 1927 Canada (New Brunswick, Newfoundland, Nova Scotia, Quebec)

NAMER12 NAMER192712

North America 1927 NAMER13 NAMER192713 Canada (Northwest Territories, Saskatchewan) North America 1927 - Canada (Yukon) North American 1927 - Canal Zone North American 1927 - Cuba North American 1927 Greenland (Hayes Peninsula) North American 1927 - Mexico North American 1983 Alaska, Canada, CONUS North American 1983 Central America, Mexico Observatorio Metereo 1939 Azores (Corvo & Flores Islands) Old Egyptian 1907 - Egypt Old Hawaiian MEAN FOR Hawaii, Kauai, Maui, Oahu Old Hawaiian - Hawaii Old Hawaiian - Kauai Old Hawaiian - Maui Old Hawaiian - Oahu Oman - Oman Ord. Survey G. Britain 1936 MEAN FOR England, Isle of Man, Scotland, Shetland Islands, Wales Ord. Survey G. Britain 1936 - England Ord. Survey G. Britain 1936 England, Isle of Man, Wales Ord. Survey G. Britain 1936 Scotland, Shetland Islands NAMER14 NAMER192714 NAMER15 NAMER192715 NAMER16 NAMER192716 NAMER17 NAMER192717 NAMER18 NAMER192718 NAMER19 NAMER192719 NAMER20 NAMER192720 AZORES EGYPT OBSERVMET1939 OLDEGYPT1907

EMC conformance

All Raymarine equipment and accessories are designed to the best industry standards for use in the recreational marine environment. Their design and manufacture conforms to the appropriate Electromagnetic Compatibility (EMC) standards, but correct installation is required to ensure that performance is not compromised.

Electronic Chart Cards

To use your C-Series Display as a navigation aid, charts with the appropriate level of detail for the geographic area you wish to navigate are required. The charts are available an electronic format on Navionics Gold Chart cards. To obtain Navionics Chart cards, contact your local dealer or visit www.navionics.com or www.navionics.it. Alternatively, anywhere in North America call Navionics toll-free on 1-800-848-5896 Outside of North America, contact your local dealer or Navionics SpA Telephone: (+39) Fax: (+39) 0584 961309
Chapter 1: Using the Display
This chapter gives an overview of the system and its features.

1.1 The C-Series wallet

Your C-Series unit is supplied with a wallet containing the following documentation: Installation Manual Reference Manual - for installation and system integration details. Reference Manual - for full operating instructions of the C-Series Display unit. Operating Guide - gives a brief, easy-to-use overview of the system and how to use it. Template - Flush mount templat.

1.2 System Overview

The C-Series display is a unit which combines chartplotter, radar, fishfinder and course monitoring applications. These applications give the following functions: Chartplotter - for navigation information, waypoint entry and route-planning. Radar - to detect the position and speed of objects around your vessel and collision avoidance. Fishfinder - to build a picture of what is below your vessel, to help find and identify targets e.g fish, wrecks etc. Course Deviation Indicator (CDI) - to help maintain your course using a rolling road display. For full functionality the display requires connection to a Global Positioning System (GPS) and a compass for the acquisition of position and heading data. The individual applications also require: Chartplotter - relevant chart card to obtain detailed information for the area in which you are navigating. Radar - a C-Series compatible scanner. Fishfinder - a suitable transducer and Raymarine digital sounder module (DSM). When used as part of a SeaTalk system it will display information from other SeaTalk instruments. It can also be integrated to an autopilot and display Digital Selective Calling (DSC) messages from a DSC VHF radio if fitted. Information from the C-Series display can also be transferred between applications and to other SeaTalk instruments within the system. A built-in simulator lets you practise using the display and its functions without it being connected to other devices (GPS, compass, scanner and transducer).

1.5 The Applications

This section introduces the way in which the various applications are presented on the display, and their main functions. Detailed operating instructions are given in the relevant chapters of this handbook. The following applications are available: Chartplotter Radar Fishfinder Course Deviation Indicator Note: Whilst not an application in its own right, waypoints are handled at system level
in the Chartplotter, Radar and Fishfinder applications and are covered in this manual in a separate chapter entitled Working with Waypoints.

Chartplotter

The chartplotter includes a small-scale world map enabling route plotting and tracking even when an electronic chart card is not installed. Detailed navigation information is displayed when a Navionics electronic chart card is installed. For more information and to obtain chart cards see the Important Information chapter at the front of this manual. A feature of the chartplotter is autorange. If you select a chart scale that does not have cartographic detail in some areas, the chartplotter will use the most detailed level available for the surrounding area and stretch it to fit the selected scale. This means that you will never have blank or hatched areas on your screen. However there may be some mis-alignment of objects which cross the chart boundary in this area.

North-Up

(Relative Motion)

FIND SHIP

ROUTES

TRACKS

PRESENTATION
Using the chartplotter you can carry out such functions as: Track the course of your vessel on the chart as you travel to a destination. View detailed information including ports and tides (if available). Place, display and edit waypoints. Navigate to a position using cursor position, waypoints and routes, manually or using an autopilot (if fitted). Set up a route that can be followed. Overlay radar data (if available) on the chart.

D6573-2

The radar application gives you information on what is around your vessel at any particular moment in time. This includes positions of landmasses, other vessels and navigation markers such as buoys. A typical radar plot is shown below:
6nm North-Up (Relative Motion) Rings 1nm

VRM/EBL.

PRESENTATION.
Using the radar you can carry out such functions as: Adjust the picture for maximum clarity, range and minimum interference. Detect the position, speed and direction of travel of other vessels. Display, place and edit waypoints. Use the Mini Automatic Radar Plotting Aid (MARPA) function to acquire targets and track them for collision avoidance. Measure the range and distance of other vessels using Variable Range Markers (VRMs) and Electronic Bearing Lines (EBLs).

D6574-2

TARGET TRACKING.

TARGETS DISPLAY.

Fishfinder
The Fishfinder application gives you a detailed view of what is below your vessel. This includes, the seabed and its texture, fish and other underwater objects. A typical Fishfinder image is shown below:

OPTIONS (Default in bold) 1min - 99hrs 59mins OFF ON 00.01 - 24:00hrs OFF ON
70F 0-99.8F 75F 0.2-99.9F

Navigation Alarms Setup

Navigation alarms will sound in any applicatioin when you are navigating.
MENU ITEM Arrival Alarm Radius The distance from the target waypoint or the closest point of approach to the target waypoint that triggers the arrival alarm to sound. Offtrack Alarm Switches the off-track alarm on or off Offtrack Alarm XTE If the Offtrack Alarm is set to ON, an alarm is triggered when the XTE for any current navigation, exceeds the value that you have specified. OPTIONS (Default in bold) 0.1nm 0.01 - 9.99nm
OFF ON 0.3nm 0.01 - 9.99nm (or equivalent in the selected Distance Unit)

Radar Alarms Setup

These alarms will only sound when you are in the radar applicaiton.
MENU ITEM Guard Zone Sensitivity Ensure that this is not set too low or targets will be missed. OPTIONS (Default in bold) 50% 0 - 100%

Fishfinder Alarms Setup

These alarms will only sound when you are in the fishfinder application
MENU ITEM Fish Alarm Switches the fish alarm on or off. Fish Alarm Sensitivity If the Fish Alarm is set to ON, an alarm is triggered when the fish return strength reaches the sensitivity that you specify. Fish Alarm Depth Limits If the Fish Alarm and this alarm is set to ON, an alarm is triggered (2 beeps) if any target meets the sensitivity level and is within the Shallow Fish Limit and Deep Fish Limit that you specify. Shallow Fish Limit Specifies the lower value for the Fish Alarm Depth LImit. Deep Fish Limit Specifies the upper value for the Fish Alarm Depth LImit Shallow Depth Alarm Switches the shallow depth alarm on or off. If a DSM is not connected, this cannot be set. Shallow Depth Alarm Value If the Shallow Depth Alarm is set to ON, an alarm is triggered if the depth drops below the value you specify. OPTION (Default in bold) OFF ON 0 10% - 100% OFF ON
> 1 fathom > 1m > 2ft > 1 fathom > 1m > 2ft OFF ON > 1 fathom > 1m 2ft Up to maximum range of transducer
MENU ITEM Deep Depth Alarm Switches the deep depth alarm on or off. If a DSM is not connected, this cannot be set. Deep Depth Alarm Value If the Deep Depth Alarm is set to ON, an alarm is triggered if the depth exceeds the value that you specify.

Note: Pressing the RETRIEVE ALL soft key, will retrieve all of a Database list to the display.
If whilst retrieving information a selection is already found to exist on the display, a warning message will appear: The soft keys will change to give you the options of: RETRIEVE AS NEW REPLACE CANCEL RETRIEVE Select which option you want by pressing the corresponding soft key.
How do I erase information from a card?
If you wish to remove information from a card, for example you no longer need it, or the card is full, it can be erased by using the DELETE or DELETE ALL soft keys that can be found on the Retrieve soft key bar. A message will be displayed on screen asking you to confirm that you want to delete the item(s), before it takes place.
2.11 How do I send and receive information using NMEA?
You can transfer and retrieve waypoints or routes to and from another instrument or PC by: To transfer or receive information using NMEA: 1. Press the DATA button. 2. Press the ARCHIVE AND TRANSFER. 3. Press the TRANSFER ON NMEA. The following soft keys are displayed

D6808-1

SEND WPTS ON NMEA

SEND RTES ON NMEA

RECEIVE ON NMEA
4. Press SEND WPTS ON NMEA, SEND RTES ON NMEA or RECEIVE ON NMEA.The transfer starts. If you wish to stop the transfer at any point, press STOP TRANSFER. 5. When the transfer is complete, STOP TRANSFER greys out and the soft keys reappear.
2.12 How can I set up my GPS?
You can set up your Global Psitioning System (GPS) and check its status using the GPS Status page of the SetupSetup menu. To access the GPS Status page: 1. Press MENU. The Setup menu is displayed. 2. Use trackpad (up/down) to highlight GPS Status. 3. Use trackpad (right) to display the GPS Status dialog box.

00001.0

SD-FIX

122 HDOP

FIX STATUS
SATELLITE DIFFERENTIAL WGS 1984

DIFF GPS ON OFF

DIFF SET UP

OTHER SET UP

RESTART GPS

D6809_2

This screen provides, for each tracked satellite, the satellite number, a graphical signal strength bar, status, azimuth angle and its elevation angle from your vessel. The sky view graphic shows the position of these satellites. Positional accuracy is dependent upon these parameters; in particular, the azimuth and elevation angles are used in a triangulation process to calculate your position. Horizontal Dilution of Position (HDOP) is a measure of this accuracy; a higher figure signifies a greater positional error. In ideal circumstances, the figure should be in the region of 1.0. The fix status can indicate: NO FIX - no satellite fix can be acquired. FIX OK - a normal GPS fix has been acquired. D-FIX - a differential fix has been acquired. SD-FIX - a satellite differential fix has been acquired. If your boat is equipped with a Raymarine GPS, the Differential GPS can to switched on or off using the appropriate soft key.

. at my current position

1. Press WPTS twice. i. A waypoint is placed at your boats position. ii. The create waypoint box and associated soft keys are displayed for a short period of time, to enable you to change the details of the waypoint. For more information refer to How can I edit a waypoint? on page 7 2. To accept the default details, either wait for the create waypoint box to disappear or press OK. Note: If the system cannot determine your position, a warning is displayed and the

waypoint is not placed.

.at a known position
1. Press WPTS. 2. Press WAYPOINT AT POSITION. The Edit Waypoint box is displayed with the highlight flashing in the position field. 3. Use the trackpad and/or the rotary control to enter the required position. 4. Press OK to place the waypoint at this position. You can now use the trackpad to scroll through and edit the details of the waypoint if required. For more information, see How can I edit a waypoint? on page 7. 5. Press OK again, to return to normal operation.

D6557-1

3.3 How do I navigate to a waypoint?
You can navigate to an existing waypoint by using the GOTO WAYPOINT OPTIONS soft key. This can either be accessed by selecting the required waypoint on screen with the cursor (chart and radar only) or via the WPTS/MOB button (all applications).

.using the cursor

D6558-1

GOTO WAYPOINT WPT

1. On the chart or radar screen, move the cursor over the waypoint you wish to go to. The cursor changes color and displays a waypoint label. The soft keys change to show you are working with a waypoint. 2. Press GOTO WAYPOINT.

.via the WPTS/MOB button

D6559-1

GOTO WAYPOINT

1. In any application, press WPTS/MOB and then GOTO WAYPOINT OPTIONS. The Waypoint List is displayed. 2. Using the trackpad (up/down), highlight the waypoint you wish to navigate to. 3. Press GOTO WAYPOINT. Notes: (1) If at any time you wish to stop navigating towards the selected waypoint, press STOP GOTO. (2) For more information on navigation, see Chapter 4: Using the Chart (3) The chart application also provides controls to GOTO a waypoint.

tion mode (see page 30) is suspended.

Panning

Panning moves the chart that is displayed to a different area. To pan a chart, simply press the appropriate arrow (left/right, up/down) on the trackpad. When the cursor reaches the edge of the screen, the chart pans.

Zoom in/out

When you zoom in, the chart scale changes to show a smaller area in more detail. Conversely, if you zoom out the chart area displayed is increased but the detail is reduced. The cartographic detail available on charts varies according to the chart and the chart scale. Some areas provide detail at smaller scales than others. To zoom in/out around your boat: 1. Use the trackpad to move the cursor to the required position. 2. To zoom in, press the lower part of the RANGE key To zoom out, press the upper part of the RANGE key. Note: To zoom in around the cursor ,you must first break the motion mode.
4.6 How do I navigate to a specific point?
You can use your Chartplotter to navigate to a specific point marked by the cursor or to a waypoint. When you are steering manually, you can also use the chartplotter to determine the bearing or direction to steer.
Go to the cursor position
Navigating using the cursor is a very simple and quick technique that involves travelling directly to a point selected by the cursor position: 1. Position the cursor at the desired destination 2. Press GOTO. If you are currently navigating to a waypoint, following a route or already navigating to the cursor, you will need to press STOP GOTO, before the system will allow you to go to the position currently marked by the cursor. 3. Press GOTO CURSOR: A temporary waypoint entitled Go to cursor is placed at the cursor position. A dashed line is drawn between your original vessel position and the temporary waypoint. This target waypoint is also identified on the radar.
4nm North-Up (Relative Motion) Local

D6493-1

GOTO CURSOR

STOP GOTO

You can either use the cursor to select and follow a route from the start, or to follow a route from a selected waypoint within the route. Follow a route from the start

D6541-1 D6717-1

FOLLOW THIS ROUTE
1. Move the cursor over any leg of the appropriate route. 2. Press FOLLOW ROUTE. Note: To stop following an active route at any time, press STOP FOLLOW. Follow a route from a selected waypoint within the route

FOLLOW FROM HERE

1. Move the cursor over the appropriate waypoint. 2. Press FOLLOW FROM HERE. Note: To stop following an active route at any time, press STOP FOLLOW.

. via the route list

This option directs you to the start of the route that you have selected on the route list and then follows it:
1. Press ROUTES. 2. Press FOLLOW ROUTE OPTIONS. The route list is displayed with the highlight on the most recently built, edited or followed route. 3. Select the appropriate route on the list. 4. Press FOLLOW ROUTE. Notes: (1) To stop following an active route at any time, press STOP FOLLOW. (2) This option can also be accessed via the GOTO soft key

ROUTES.

. in reverse order
This option reverses the waypoint order in the selected route and then follows it.

D6878-1

REVERSE AND FOLLOW
1. Press ROUTES. 2. Press FOLLOW ROUTE OPTIONS. The route list is displayed with the highlight on the most recently built, edited or followed route. 3. Select the required route on the list. 4. Press REVERSE ROUTE. The route is reversed; the last waypoint of the original route is now the first, the waypoints renumber and the route name moves accordingly. The system then automatically activates the follow route function. Note: To stop following an active route at any time, press STOP FOLLOW.
. to advance to the next waypoint within a route
If you are following a route, you have the option to advance to the next waypoint in that route. In the example below, the advance waypoint option was selected at Waypoint 2. This has resulted in Waypoint 3 being dismissed and the course of the route advancing to Waypoint 4

W.Wight 1

W.Wight 5
Note: If the current destination is the last waypoint, then it advances on to the first

waypoint in the route

D6603-1
4.8 How do I monitor where I am going?

. using chart vectors

D6548-1

CHART VECTORS

You can display a variety of graphical indicators to help monitor where you are going:
Heading (HDG) and course over ground (COG) vectors

Heading vector (HDG)

Course over ground (COG)

D6772-1

break will occur in the track. In this case only the last segment can be converted into a route.

To stop tracking.

D6501-1

STOP TRACK

To stop laying a track, press STOP TRACK. You are asked what you want to do with your track: To save this track, press SAVE. The Save Track box is displayed to enable you to change the tracks name or color. See How do I change the name or color of a route or track? on page 26. To delete this track from the system, press DISCARD TRACK. A warning message is displayed. To resume tracking, press CANCEL STOP COMMAND.
How do I create a route from a track?
Creating a route from a track enables you to retrace a saved track. When a track is converted the system creates the closest route through the recorded track, using the minimum number of waypoints. Each waypoint created will be saved with the depth and temperature data (if applicable) for that position. On completion, the maximum deviation of the route from the recorded track is displayed and the new route is added to the route list. It can now be displayed, edited and erased etc. in the same way as other routes in the system. Note: If a track break occurs, only the last segment is converted to a route.
. from the current track?
You can create a route from the track that you are currently laying. This method will take a snapshot of the track to date, convert it to a route and then continue laying the track:
CREATE ROUTE FROM TRACK CREATE ROUTE FROM TRACK
1. Press CREATE ROUTE FROM TRACK. The track list is displayed.

D6505-1

2. Press CREATE ROUTE FROM TRACK again. The system generates the route, displays the maximum deviation from the recorded track and asks if you want to give the route a name of your choosing. 3. Press: YES to assign this route a name of your choice. (see How do I change the name or color of a route or track? on page 26).
NO to assign this route a default name.

.from a saved track?

You can create a route from a track that you have already saved:
1. Move the cursor over the appropriate track or highlight it on the track list. 2. Press CREATE ROUTE FROM TRACK. The system generates the route, displays the maximum deviation from the recorded track and asks if you want to give the route a name of your choosing. 3. Press: YES to assign this route a name of your choice (see How do I change the name or color of a route or track? on page 26).
4.10 How do I edit my routes and tracks?

D6782_1
4.13 How do I set up my chart and its cartography?
The set up for your chartplotter and its cartography can be changed from the standard configuration to suit your particular needs. Although you will probably only do this when you first use the chartplotter, you may decide to make subsequent adjustments once you become more familiar with the system. Any settings that you change are retained even when you power off. To select the chartplotter set up menus, press MENU and then select either Chart Setup or Cartographic Setup.

Chart Setup

FUNCTION
Description Object Information When set to ALL ON, details of cartographic area (including objects) is displayed when selected with the cursor. When set to POINTS ON, details of individual cartographic objects is displayed when selected with the cursor. Vector Length The time period specified for drawing COG and Heading vectors. *Datum Grid moves according to datum selected and the lat/long of cartographic features change. System attempts to set up any GPS to the new mode and indicates whether successful or not.

OPTIONS

(Default in bold) OFF All ON Points ON 3 Mins 6 Mins Infinite WGS 84 List of datum provided
CAUTION: * Changing the chart datum does not cause any waypoint or routes stored in the chartplotter to move on the display, although their latitude and longitude changes to reflect the new datum. When adding waypoints numerically to the waypoint list, or via SeaTalk, NMEA OR hsb2, it is important that they are referenced to the same datum to which the display is currently set.

Cartography set up

Description Chart Display The level of detail shown on the chart. Chart Grid Grid lines of latitude and longitude. Chart Text Text appearing on the chart e.g. place names etc. Chart Boundaries The line indicating the boundary of the chart. Spot Soundings Number on the chart indicating depth. Safety Contour Areas with depths shallower that the specified value, are shaded in a darker blue than those areas with depths greater than the specified value.
(Default in bold) Detailed Simple ON OFF ON OFF ON OFF ON OFF OFF 7ft 16ft 33ft 66ft (Contour always drawn at or deeper than the selected depth). ALL 5m 10m 20m OFF ON OFF International US ON OFF ON OFF ON OFF ON OFF
Depth Contour A line indicating the depth at a particular position.
Nav. Marks Nav. Marks Symbols The set of symbology used for navigation marks. Corresponds to paper charts. Light Sectors The sector of light cast by a fixed beacon. Caution & Routing Data Marine Features The cartographic features that are displayed on the water. Land Features The cartographic features that are displayed on the land.
Note: See Chapter 2:General Operation and System Setup for all other set up menus.
4.14 How does my chart warn me of potential dangers?

The first VRM/EBL will be placed at a location of 1/3 of the current range and 030 relative to your boats head. If this setting is adjusted, the display will retain the adjustments and use them when the VRM/EBL is next turned on. To use VRMs/EBLs to tell you the range/bearing of a target: 1. Toggle VRM/EBL soft key to ON. The VRM/EBL will be shown on the radar picture with your boat at its center. 2. ADJUST VRM and VRM are highlighted to indicate it can be adjusted. 3. Use the rotary control to adjust the VRM to the required size. 4. Press OK to remove the highlight and retain the adjustment. 5. Press ADJUST EBL. This will highlight the EBL. 6. Use the rotary control to place the EBL over the required target. 7. Press OK to remove the highlight and retain the adjustment. Note: You can also push the rotary control to accept an adjustment and toggle control
to the other object (VRM or EBL).

D6597-1

VRM/EBL 1 ON OFF

ADJUST VRM 1.991nm

ADJUST EBL 124P

FLOATING EBL.

SET UP VRM/EBL 2
The distance and bearing of the target is now shown in the ADJUST VRM and ADJUST EBL soft key labels. You will be able to tell which way the target is traveling by watching how it moves in relation to the EBL. If it continues traveling directly along the EBL, it shows that it is on a possible collision course with your boat - take the appropriate action. To place a second VRM/EBL use the SET UP VRM/EBL 2 soft key and repeat steps 1 to 7above. This VRM/EBL will be placed at a location of 2/3 of current range and a bearing of 330.
. Using floating VRMs/EBLs
You can use the VRM/EBL float function to measure the range and bearing between any two points on the radar screen. This function allows you to move the VRM/EBL away from your boats position and onto a target. You can then change the radius of the VRM to determine the distance between two points and change the angle of the EBL, relative to its new origin, to obtain the bearing.
How do I float a VRM/EBL?
1. Create the VRM/EBL as described previously. 2. Press FLOATING EBL. 3. Press ADJUST FLOAT. This will highlight the VRM/EBL. 4. To set the origin to a difference position: i. Use the trackpad to move the centre of the VRM/EBL over the first target. ii. Press OK to retain the adjustment and remove the highlight. 5. To adjust the VRM: i. Press OK to access the soft keys. ii. Press ADJUST VRM to highlight the VRM. iii. Use the rotary control to move the VRM over the second target. The distance between the first and second target is shown on the ADJUST VRM soft key. 6. To adjust the EBL: i. Press ADJUST EBL to highlight the EBL. 7. Use the rotary control to adjust the EBL over the second target. The bearing between the first and second target is shown on the ADJUST EBL soft key. 8. Press OK to retain the adjustment. 9. If required, you can float a second VRM/EBL: i. Press SET UP VRM/EBL 2. ii. Toggle the VRM/EBL 2 to ON. iii. Repeat steps 1 to 8 above.

.from the MARPA list

To cancel a target from the MARPA list: 1. Press MARPA LIST. The MARPA database list is shown. 2. Use the trackpad to highlight the target you wish to cancel. 3. Press CANCEL TARGET to remove the selected target or Press CANCEL ALL TARGETS to remove all the targets in the MARPA list. 4. Press OK to remove the MARPA database list.
5.10 How do I mark a position on the radar screen?
You can mark a position on the radar screen by using a waypoint. Waypoints are positions marked on the screen as a reference or destination point and are stored in the Waypoint list. They can also be used to build routes and assist in passage planning. Waypoints are placed on the radar screen via the WPTS/MOB button in the same way as they are placed on a chart. For full details on using waypoints and passage planning see Chapter 3: Working with Waypoints and Chapter 4: Using the Chart.
5.11 How do I set up my radar?
The set up for your radar can be changed from the standard configuration to suit your particular needs. Although you will probably only do this when you first use the radar, you may decide to make subsequent adjustments once you become more familiar with the system. Any settings that you change are retained and become the default settings even when you power off. To select the Radar Setup menus, press MENU when a radar window is active and then select Radar Setup. Note: When a radar window is active, you can also access this menu by pressing the
TARGETS DISPLAY soft key and then pressing and holding the INT.REJECT, EXPANSION OR WAKES key.

Function Description

Interference Rejection When Interference Rejection is switched ON, any mutual radar interference between two radar equipped vessels operating within range of each other, is automatically reduced. Target Expansion When Target Expansion is switched ON, targets are magnified to make them easier to see. Wakes Period When wakes is switched ON, the target is displayed at the brightest level and its previous positions are retained at successively fainter levels on the screen. Timed Transmit Controls the radars timed transmission power-save mode Transmit Period When Timed Transmit set to ON, the scanner performs the number of scans specified and then shuts down for the number of minutes specified by the Standby Period. Standby Period Indicates the number of minutes that the system shuts down - the scanner does not rotate and the display is in standby mode. Bearing alignment Corrects for display azimuth error. Please refer to the C-Series Installation Guide. Radar Advanced Setup Please refer to the C-Series Installation Guide. OFF ON

NORMAL HIGH

LOW HIGH 10 seconds 30seconds 1 minute 5 minutes 10 minutes OFF ON 10 scans 20 scans 30 scans 3 minutes 5 minutes 10 minutes 15 minutes
5.12 How does my radar warn me of potential dangers?
Chapter 6: Using the Course Deviation Indicator

(Default in bold) YES NO

YES NO AUTO LOW MEDIUM HIGH OFF LOW HIGH 26 pings per second 5 to 30 pings per second (15 pings maximum when radar and fishfinder application in more than one pane and when fishfinder frequency is set to SINGLE.) Disabled Enabled
2nd Echo Interference Rejection Minutely adjusts the ping rate according to the 2nd echo level. Results in better sensitivity of the image. Ping Rate Limit (per sec.) Provides a speed limiter; it is useful to adjust the ping rate to suit local conditions. For example, the ping rate may be too fast when there is a hard bottom in shallow water.
Ping enable The sonar ping is normally enabled. It can be disabled. This is useful when other equipment is being tested, or if someone is diving beneath the boat.

Controlling the image

Once you have set up the transducer as described above, the DSM will locate the bottom and display a scrolling fishfinder image. The Fishfinder Display Setup Menu provides controls to change this image as follows:
Depth Digit Size The size of the digit indicating the depth Depth Digit Position The position of the digit indicating the depth Target Depth ID Controls whether the depth of identified targets d are displayed. N.B. The level of targets displayed is directly linked to the level of Fish Alarm sensitivity (see General Operation and System Setup: Fishfinder Alarms Setup). Depth Lines Controls whether horizontal lines indicating depth are displayed Color Palette Choose the color palette to suit different conditions/your personal preference.
(Default in bold) SMALL MEDIUM LARGE BOTTOM TOP ON OFF
ON OFF Classic Blue Classic Black Classic White Sunburst Greyscale Inverted Greyscale Copper Night Vision MANUAL AUTO 10-100% 100%
Scroll Select AUTO to vary the scroll speed in relation to your boats speed or MANUAL to specify the Scroll Speed. Scroll Speed If Scroll is set to MANUAL, specify the percentage of the normal speed that screen should scroll at (see Adjusting the scroll speed on page 14 for more details).
7.9 What other settings affect the fishfinder image?
The system automatically adjusts the following settings in order to optimise the fishfinder image: Operatiang frequency. Gain modes (Gain, Color Gain, TVG) Power setting. They should not ordinarily require adjustment. You can however make adjustments manually if required.
What are the operating frequency modes?

D6671-1

FREQUENCY AUTO MAN

FREQ MODE SINGLE DUAL

SELECTED FREQ 200 50

DISPLAYED FREQ 200 50

The DSM provides four frequency modes: Automatic - the system automatically selects the appropriate frequency according to your depth. As the depth increases , the DSM changes the frequency from 200 kHz to 50 kHz; as the depth decreases, it switches from 50 kHz to 200 kHz. This mode is useful for automatically searching for the bottom. 50 KHz - scans a wide area and penetrates water well, so is good for use in deep water. 200 KHz - scans a narrower area, but produces a more detailed view so is good for finding fish that are near the bottom or close together. It is better for use in shallow water. Dual frequency - Alternates pings between both 200 kHz and 50 kHz. When Dual Frequency is selected, you must select the frequency shown (200 kHz or 50 kHz) in the active window.

Who do I contact for product repair and service?
In the unlikely event that your Raymarine unit should develop a problem, contact your authorized Raymarine dealer for assistance. The dealer is best equipped to handle your service requirements and can offer timesaving help in getting your equipment back into normal operation. If repairs cannot be obtained conveniently, obtain product service by returning the unit to: Raymarine Product Repair Center 22 Cotton Road, Unit D, Nashua, NH03603-4219 The Product Repair Center is open Monday to Friday 0815 to 1700 Eastern Standard Time or Eastern Daylight Savings Time. All products returned to the Repair Center are registered upon receipt and a confirmation letter is sent to acknowledge the repair status and the reference number of the product. We will make every effort to carry out the repair and return your unit as quickly as possible.
If you wish to enquire about the repair status of your unit, contact the Repair Center at: 1-800-539-5539
How can I contact Raymarine in Europe?
You can obtain Technical Support, service and accessories from your authorized Raymarine dealer, or by contacting: Raymarine Limited Anchorage Park, Portsmouth PO3 5TD, England Tel +44 (0)4713 Fax +44 (0)4642
Appendix A: Specification
C70, C80 and C120 LCD Color Displays General
Approvals CE - conforms to FCC - conforms to Size C70 C80 C120 C70 C80 C120 1999/5/EC, EN6095:1997 Part 80 (47CFR) and Part 2 (47CFR) 253 x 175 x 110 mm (9.9 x 6.9 x 4.3 in.) excluding bracket 283 x 210 x 110 mm (11.1 x 8.2 x 4.3 in.) excluding bracket 356 x 264 x 114 mm (14.0 x 10.4 x 4.5 in.) excluding bracket 1.2 kg. (2.6 lbs) 1.8 kg. (3.9 lbs) 3.0 kg. (6.6 lbs) Bracket with panel mount option External 10.7 - 32 v DC required Floating earth/ fully isolated Consumption with full brightness: C70 9W CW CW Waterproof to CFR46; suitable for external mounting -10 C to +50 C up to 95% at 35C non-condensing 9 defined keys, 5 soft keys, trackpad and rotary control Context sensitive, provides range/bearing or lat/lon g or depth/ range on fishfinder Color TFT LCD C70

Weight

Mounting Power
Environmental: Op/Storage Temp. Range Humidity limit Controls Cursor Display type Resolution