PAGE ACTIVE WPTS/ MOB DATA MENU

CANCEL

Softkeys Press to select the corresponding function identified by the on-screen label Power Press once to turn ON. Press again to access backlight functions and scanner controls. Press and hold to turn the display OFF. RANGE Press to change the display scale so that a smaller or larger area can be seen on the screen. Chart Card slot Open the cover to install CompactFlash cards.

D7517_1

81221_4.book Page 7 Tuesday, February 28, 2006 5:24 PM

Buttons and soft keys

To navigate to the required function you will need to press a series of buttons and/or soft keys:
Buttons Access system functions or change what you see on-screen. Within the text of this document they are written in bold capitals e.g. WPTS/MOB. Press and hold to access short cuts.
ACTIVE WPTS MOB DATA MENU
Soft keys They change depending on application or function being performed. Press the corresponding key (below the screen) to select. Further soft keys may be displayed. If a key has several options, each press will highlight the next option. If a key displays a single value or a slider above, use the rotary control to adjust. Within the text of this document they are written in capitals e.g. SORT LIST.
WAYPOINT AT CURSOR WAYPOINT AT VESSEL WAYPOINT AT LAT/LONG. GO TO WAYPOINT OPTIONS REVIEW AND EDIT WAYPOINTS

ERASE WAYPOINT

SORT LIST
SET DEFAULT SYM & GROUP.

WAYPOINT GROUPS.

VIEW AND EDIT DETAILS
SET UP DEFAULT SYMB GROUP

EDIT DEFAULT

This process of pressing buttons and soft keys to navigate to the required function is simplified in this manual and represented by a strip e.g.

WPTS MOB

REVIEW AND EDIT WAYPOINTS. SET DEFAULT SYM & GROUP. SET UP DEFAULT SYMB GROUP
Note: The key beep that you hear whenever a button or soft key is pressed, can be switched off and the soft keys automatically hidden if required. For more details, please refer to the Display Setup Menu on page 191.

D7365-2

D7364-2
Example: The example above shows the series of button and soft key presses required to change the waypoint default symbol or group.
81221_4.book Page 8 Tuesday, February 28, 2006 5:24 PM

The cursor

When you are using the chart and radar applications, the cursor is used to move around the screen: The cursor appears on the screen as a white cross.

D7366_3

If the cursor has not been moved for a short period of time, it changes to a circle with a cross in it, to make it easier to locate on the screen.

Rings nm Rings nm

Status bar
Gives information specific to each application. MARPA ALARMCannot be edited or moved. MARPA ALARM
Target lost (on screen) Target lost (on screen)

ACKNOWLEDGE ACKNOWLEDGE

to your particular needs.
* For details of how to adjust and edit the data bar, please see page 180
Note: To change the size of the text on screen, please see page 191.

D7456_2

Data base lists Data base lists Contain information you Contain information you have added to the display's memory have added to the display's e.g. waypoints. memory e.g. waypoints. Highlight an entry with Highlight an entry using trackpad or rotary trackpad or rotary control to control to display related information. display related information. Editable using soft keys. Editable using soft keys.
Pop-up messages Pop-up messages Alert you to a situation e.g. Alert you to a situation e.g. alarm, function not available. alarm, function not available. Not editable. Not editable. May require a response e.g. May require a response e.g. press ACKNOWLEDGE press ACKNOWLEDGEto to silence alarms. silence alarms.
Dialog boxes Dialog boxes Enable data to be edited oror Enable data to be edited entered into aastore/list e.g. entered into store/list editing a waypoint. e.g. editing a waypoint. Menus (see next page) Menus (see next page) Used to configure system to Used to configure system your particular needs.

D7456_1

81221_4.book Page 10 Tuesday, February 28, 2006 5:24 PM

MENU MENU

D6582-1
Menus enable you to configure your system to your particular needs. Whenever the MENU button is pressed, the Setup menu is displayed containing a list of all the menus available for the active application together with system wide menus e.g.
Setup Menus for the active application External equipment/ instruments
Radar Setup. GPS Status. Compass Setup. AIS Layer Status. System Setup. Alarm Setup. Display Setup. Databar Set. Select Page Setup. System Diagnostics. Remove CF Card

System-wide menus

For details of application menus, please refer to the appropriate chapter. For all other settings, please refer to Chapter 12:System setup and customizing. To access a menu: 1. Select the appropriate menu and setting:
Setup Chart Setup. Cartography Setup. GPS Status. Compass Setup. Cartography Setup Menu Chart Display Chart Grid Chart Text Chart Boundaries Spot Soundings Detailed On On ON ON

Show/hide waypoint names

You can show or hide all waypoint names if required:
PRESENTATION. SHOW/HIDE WAYPOINTS. WAYPOINT NAME ON

Select status

D8306_1

D8302_1

81221_4.book Page 42 Tuesday, February 28, 2006 5:24 PM
Showing/hiding waypoint symbols
You can define which waypoint symbol types are shown/hidden in the radar or chart application: 1. Display the SHOW BY SYMBOL option:
PRESENTATION. SHOW/HIDE WAYPOINTS. SHOW BY SYM

Select SYM

2. To change the status (show or hide) of a symbol type:

ON RADAR SHOW HIDE

SHOW HIDE SHOW HIDE

SHOW BY SYMBOL

M Fish Ra Day

ON CHART SHOW HIDE

Note: Waypoints in an active route are always displayed, regardless of whether the
display is set to show or hide.
Showing/hiding waypoint groups
You can define which waypoint symbol types are shown/hidden in radar or chart applications: 1. Display the SHOW BY GROUP function.
PRESENTATION. SHOW/HIDE WAYPOINTS. SHOW BY GROUP

Select GROUP

2. To change the status (show or hide) of a waypoint group:

SHOW BY GROUP

My Waypoints Fishing Racing Day trips SHOW SHOW SHOW HIDE

D8305_1

D8721_1

D8304_1

D8839_1
81221_4.book Page 43 Tuesday, February 28, 2006 5:24 PM
Chapter 4: Using the Chart

4.1 Important

Safety
When using your chartplotter you should always check that a route is safe. Zoom in to check for hazards, such as small shoals, that may not be shown on a smaller scale chart. Until you are familiar with interpreting the chart display, you should take every opportunity to compare the displayed objects with visual targets, such as buoys and coastal structures. You should practice harbour and coastal navigation during daylight and in clear weather conditions. The simulator mode can also be used to help you gain experience. It is strongly recommended that before you use your chart application, that you read and understand Chapter 3:Working with Waypoints.

Follow using the cursor

You can either use the cursor to select and follow a route from the start of the route or from a selected waypoint within the route. from the start of the route

FOLLOW THIS ROUTE

D7510-2
Position cursor over any leg of required route
. from a selected waypoint within the route

FOLLOW FROM HERE

D6717-3
Position cursor over appropriate waypoint
Follow using the route list
This option directs you to the start of the route that you have selected on the route list and then follows it:

Route List

GOTO. Or: ROUTES. FOLLOW ROUTE OPTIONS.

Color -------------

Name Quick Route Route 1 Route 2 Route 3

FOLLOW ROUTE

Follow in reverse order
This option reverses the waypoint order (i.e. the last waypoint of the original route is now the first) and renumbers the waypoints accordingly. The route name moves to the reassigned first waypoint and then the system automatically activates the reversefollow route function.

REVERSE AND FOLLOW

D8362_1

Select required route

Reverse-follow route starts
Note: To stop following an active route at any time, press STOP FOLLOW.

D6539-4

Select route to follow

To start follow route

81221_4.book Page 66 Tuesday, February 28, 2006 5:24 PM
Advance to the next waypoint in a route
If you are following a route, you have the option to advance to the next waypoint in that route.
Example: In this example, the advance waypoint option was selected following arrival at Waypoint 2. This has resulted in Waypoint 3 being dismissed and the course of the route advancing to Waypoint 4.

4 W.Wight 5

W.Wight 1
To advance to the next waypoint in a route:

GOTO Or ADVANCE WAYPOINT

Note: If the current destination is the last waypoint, then it advances on to the first

waypoint in the route.

When you are following a route or going to a waypoint, you can restart the XTE. This results in a new course from the current vessel position to the current target waypoint. Restarting XTE is useful if you find yourself off track and want to go straight to your target, rather than get back onto the original track. Although RESTART XTE causes your vessel to change course, it does not affect the saved route.
When you are following a route.

D6549_3

D6499-4
Position cursor over route

D6603_3

81221_4.book Page 67 Tuesday, February 28, 2006 5:24 PM
Viewing details of routes

DEPTH 10ft

To save position

D8455_1

Move depth marker over target
Note: To return the marker to its previous position, press CANCEL

D8453_1

81221_4.book Page 110 Tuesday, February 28, 2006 5:24 PM

5.7 Fishfinder alarms

In addition to the system alarms (see page 187), the following alarms can be set when you are connected to a DSM or when the simulator is on: Fish Alarms - sound when a target meets the specified sensitivity level and, is within the depth limits (if enabled). The greater the fish alarm sensitivity, the greater the number of target image depths displayed. Shallow/Deep Alarms - sound when the DSM detects that the depth is less than the shallow limit, or greater than the deep limit. You can switch the alarms on, set the limits and specify the fish alarm sensitivity as described onpage 188.
5.8 Setting up your fishfinder
The set up for your fishfinder can be changed from the standard configuration to suit your particular needs. The Fishfinder Setup Menu is divided into three sections: Display settings. Transducer settings. DSM settings. To select the Fishfinder Setup Menus:
Fishfinder Setup Menu Setup Fishfinder Setup. Depth Digit Size Depth Digit Position Target Depth ID Depth Lines Color Palette Scroll Manual Scroll Speed Select Transducer Select Speed Transducer Depth Offset (Waterline) Depth Offset Temperature Offset Frequency Calibration. DSM Reset. Trip Counter Reset. SONAR interference Rejection 2nd Echo Interference Rejection Ping Rate Limite (per sec.) Ping Enable LARGE BOTTOM OFF OFF Copper MANUAL 100% P65/P66 UNKNOWN 0.0ft 100% 0.00F
GPS Setup. Compass Setup.

Display settings

Transducer settings

Auto OFF 30

DSM settings
Note: For general information on the Setup Menus, see page 183.

D8456_1

Select required function
81221_4.book Page 111 Tuesday, February 28, 2006 5:24 PM
The display settings provide controls to change the fishfinder image. These settings are applied locally and will therefore only affect the individual display on which you are working:

MENU ITEM

Depth Digit Size The size of the digit indicating the depth Depth Digit Position The position of the digit indicating the depth Target Depth ID Controls whether the depth of identified targets are displayed. N.B. The level of targets displayed is directly linked to the level of Fish Alarm sensitivity (see page 188). Depth Lines Controls whether horizontal lines indicating depth are displayed Color Palette Choose the color palette to suit different conditions/your personal preference.

FREQUENCY AUTO MAN

FREQ MODE SINGLE DUAL

SELECTED FREQ BOTH

D7353-2
Toggle to required frequency
Note: Changing the frequency in a single fishfinder window will automatically change all other fishfinder windows to that frequency.
81221_4.book Page 115 Tuesday, February 28, 2006 5:24 PM
Dual frequency mode In dual frequency mode the DSM pings at the same rate but alternates between 200 kHz and 50 kHz. This allows you to select the required frequency(s) - 50kHz, 200 kHz or BOTH for each individual fishfinder window. Combine this mode with the zoom, bottom lock and A-scope functions to customize each fishfinder window to meet your particular requirements or fishing conditions. For example, when you are in deeper water you can set one fishfinder application to 200 kHz and another to 50kHz. Display the 50 kHz in normal mode to show full bottom detail and a long history. This will give you an overview of the current fishing conditions. Display the 200 kHz window in fullpan zoom to view the top of the water column in very high detail and see fish swimming near the surface. In a third fishfinder application, select BOTH to split the window and display a high resolution image (200 kHz) and a wider cone (50kHz) simultaneously. Using these settings covers all possibilities and ensures that nothing is missed. Note: When BOTH (default) is selected, any changes that you make to the zoom, bot-
tom lock, A-scope etc. will be applied to both images within that window.
To select the dual frequency(s) for the active fishfinder window:

D9059_1 D7357-2

Gain modes
You can make various adjustments to the gain modes if required: Gain mode. Auto gain. Color gain. TVG. Note: In addition to the controls described in this section, the Fishfinder Setup options
allow you to adjust the Interference Rejection, 2nd Echo Interference Rejection and Ping Rate Limit. These options are described on page 110.

Auto gain modes

FISHFINDER SETTINGS. GAIN. GAIN MODE AUTO LO AUTO GAIN MED HIGH
Toggle to required setting
81221_4.book Page 116 Tuesday, February 28, 2006 5:24 PM
The gain, or sensitivity, of the display adjusts background noise by varying the echo strength for display. The value of the GAIN control determines the strength above which echoes are displayed. There are three AUTO GAIN modes: Low is ideal for viewing fishfinder images with a minimum of background noise as you are cruising to your fishing spot. Only the strongest echoes are displayed. Medium is a slightly higher gain setting that displays more detailed echoes as you are trolling. This is the default mode. High gives the best details of the targets you have located but also displays the most background noise and surface clutter. This is suitable when you are fishing. With all of these modes, the DSM will automatically adjust the Gain setting for current conditions and adjust separately for each frequency. Any adjustments made apply to all windows using that frequency.

D3968-4

81221_4.book Page 123 Tuesday, February 28, 2006 5:24 PM

Rain or snow clutter

The radar can see echoes from rain or snow. Returns from storm areas and rain squalls consist of countless small echoes that continuously change size, intensity and position. These returns sometimes appear as large hazy areas, depending on the intensity of the rainfall or snow in the storm cell.

Interference

When two or more radar-equipped vessels are operating within range of each other mutual radar interference can occur. This usually appears as a spiral of small dots from the display centre This type of interference is most noticeable at long ranges.

D6601-2

D3967-4
81221_4.book Page 124 Tuesday, February 28, 2006 5:24 PM
6.3 Powering on/off the various scanner operating modes
To control the power to the radar:

SCANNER OFF

SCANNER ON

RADAR TX

D8397_1

Switch scanner ON or OFF

Select required operating mode
The scanner icon in the data bar indicates the chosen status and is described as:
Radar Mode Transmit (TX) Radar status icon
Status description/use Scanner on and transmitting. When SCANNER set to ON, select this mode to activate scanner. This is the usual mode of operation. Scanner on but not transmitting and antenna not rotating. Antenna does not rotate, the scanner does not transmit and the radar data is removed from the screen. This is a power save mode used when radar not needed for short time periods. When you return to transmit mode, the magnetron does not need to warm up. This is the default mode. Scanner powered off When radar not required but display in use for other applications e.g. chart. When selected, system countdowns - during this time you cannot re-power the scanner. Scanner switches between on/transmitting & standby mode Power save mode when constant use of radar not required. To set up this option, see page 148

(Rotating icon)

Standby (STDBY)

D7441-1

(grayed-out icon)

(rotating/static icon)

Note: When an open array antenna is fitted, the system stops the antenna in the for-

PRESENTATION EBL REFERENCE M/T REL

D6897-2 D6898-2

6.7 Getting the best picture
You can improve the quality of the radar picture by using: The gain controls - sea, gain, tune, FTC and rain. The target display controls - interference rejection, expansion, wakes.

Using the GAIN functions

The gain function reduces the effects of false echoes and clutter. For the best results Raymarine recommends that you retain the AUTO default setting. You can however adjust these settings manually if required.
The sea, gain and tune controls can all be adjusted manually if necessary:
SEA HBR GAIN AUTO MAN TUNE AUTO
SEA MAN GAIN MAN TUNE MAN

D8406_1

Toggle to manual (MAN)
Note: The new values remain set even when you switch off the display and are applied
to both the active window and any other radar windows.
81221_4.book Page 131 Tuesday, February 28, 2006 5:24 PM
Radar echoes from waves around your boat can clutter the centre of the radar picture, making it difficult to detect real targets (see page 122). Adjusting the sea mode will reduce this clutter for up to 5 nautical miles (depending on wave and sea conditions) from your boat. This has the effect of reducing the sea echoes to intermittent small dots whilst small targets remain visible and persistent. Gain levels further from your boat remain unchanged. There are three sea gain modes: HBR (Automatic Harbor mode) - this takes account of the effects of land clutter so that small target are not lost. It should be used when you are in harbor or in close proximity to land. OSH (Automatic Offshore mode) - the system continually calculates the required level of sea clutter control. MAN (Manual mode) - this enables you to select the sea clutter level and then adjust the settings to ensure that all close small targets are visible. On short range scales, do not set the SEA control so high that all clutter is removed, since this could stop you seeing echoes from close targets. The acuteness of the sea clutter curve is set up in the Radar Setup menu (see page 149). Manual sea clutter mode should be used in conjunction with the GAIN function (described below).
The gain function makes the radar picture clearer by changing the sensitivity of radar reception. For long ranges - select a sensitivity level that gives a slight speckle in the background. Be careful not to set the gain too low, or you may miss weak or small targets. For shorter ranges - reduce the gain slightly to reduce the speckle and therefore improve target definition. Note: If you set the GAIN to MAN (manual), you should check it every time you change

Using the enhance echoes functions
You can improve visibility with the enhance echoes function.

Interference Rejection

ON The interference rejection function, which is normally left switched on, automatically reduces any mutual radar interference when two radar equipped vessels are operating within range of each other (see page 123). To change the interference rejection setting:
81221_4.book Page 133 Tuesday, February 28, 2006 5:24 PM
Radar Setup. GPS Status. Compass Setup.
Radar Setup Menu Interference Reject NORMAL Target Expansion LOW Wakes Period 1 min
Highlight Radar Setup Select Radar Setup
Select Interference Reject Select NORMAL or HIGH

D8414_1

Note: This menu can also be selected by pressing and holding INT. REJECT. OFF

D8416_1 D8420_1 D8419_1

If you wish to detect the presence of other radars in the vicinity:

ENHANCE ECHOES.

INT REJECT ON OFF

Expansion

The expansion function allows you to either override the pulse length or to give larger returns so targets are easier to see: Overriding the pulse length To override the pulse length: 1. Select the Radar Setup Menu:
Interference Reject ENHANCE Target Expansion ECHOES.Period Wakes Radar Setup Menu NORMAL EXPANSION HIGH ON OFF 1 min

Select Target Expansion

D8417_1
Enter Target Expansion option
Select HIGH 2. Set the magnification level for target expansion to HIGH:
Larger returns To alter the processing to give larger returns: 1. Select the Radar Setup Menu:
ENHANCE ECHOES. EXPANSION ON OFF
2. Set the magnification level for target expansion to LOW:
Select Target Expansion Enter Target Expansion option

Select HIGH

Note: Selecting this option may compromise target resolution.
81221_4.book Page 134 Tuesday, February 28, 2006 5:24 PM
When the wakes function is switched on, you can see the direction and speed of moving targets relative to your boat. A target is displayed in yellow and as the signal diminishes with time it is shown in paler shades of blue. Displaying wakes To switch on the wakes function:

ENHANCE ECHOES. WAKES ON

Specifying the wake period You can select via the Radar Setup Menu, whether these wakes are shown for periods of 10 seconds, 30, seconds, 1 minute, 5 minutes or 10 minutes. To specify the wake period:

Setup Radar Setup.

D8421_1
Highlight Wakes Period Select Wakes Period

D8422_1

Select wakes period
Note: You can also enter the Radar Setup Menu by pressing and holding the WAKES

soft key.

Removing wakes When the currently displayed wakes are no longer required they can be remove from your screen:

D8423_1

CLEAR WAKES
81221_4.book Page 135 Tuesday, February 28, 2006 5:24 PM

81221_4.book Page 144 Tuesday, February 28, 2006 5:24 PM

How is a risk assessed?

Each target is monitored to see if it will be within a certain distance from your boat within a certain time. If so, the target is designated as dangerous and an audible warning is sounded along with an on-screen warning being shown. The target symbol changes to the dangerous target symbol and flashes to indicate that it is a dangerous target. Pressing the appropriate soft key will silence the alarm and remove the warning. If a target is lost, either because the MARPA software has lost contact with it, or because it has moved out of range, an audible alarm is sounded and an on-screen warning appears. The on-screen symbol will change to the target lost symbol. Pressing the appropriate soft key will silence the alarm and remove the on-screen warning and the target lost symbol.
How far from my boat does MARPA work?
MARPA target acquisition is only available at radar range scales of up to 12nm, although tracking continues at all ranges. If you change to a smaller range scale, targets may be beyond the range of your scanner and will be lost. In such cases, an on-screen warning will indicate that the target is off-screen.
What happens to target data?
All MARPA targets are stored in a MARPA database list which shows the following information:

MARPA LIST

ID Bearing 022 T 025 T

Range 0.000nm 0.000nm

True Course 180 T 180 T

True Speed 0.0kts 0.0kts

CPA 0.000nm 0.000nm

TCPA 00h00m00s 00h00m00s

TARGET TRACKING

MARPA LIST.

Target display
Each target is displayed as a symbol which indicates its status:
Target being acquired Safe target

Dangerous target

D7542_2

Lost target

D6811_2
81221_4.book Page 145 Tuesday, February 28, 2006 5:24 PM

MARPA targets

CPA graphics
CPA graphics show vectors for your vessel and a selected target. A vector is a line onscreen showing the predicted courses of your vessel and the selected target if you both remain on your present course. These vectors vary in length due to boat speed and vector length set in the MARPA Setup menu.

Vector CPA graphic

To display the CPA graphic and associated soft keys:
CPA GRAPHIC ON CPA GRAPHIC OFF CPA GRAPHIC AUTO

Alarm Setup Menu

System Alarms Setup. Navigation Alarms Setup. Radar Alarms Setup. Fishfinder Alarms Setup.
GPS Status. Compass Setup. System Setup. Alarm Setup.
Highlight Alarm Setup menu Enter Alarm Setup menu
Highlight appropriate sub-menu

D8438_1

Enter sub-menu
Note: For more details of alarms, see page 27 and page 187.
81221_4.book Page 151 Tuesday, February 28, 2006 5:24 PM
Chapter 7: Using the data application

7.1 Introduction

The data application enables you to view numeric data generated by the system or by instruments available on NMEA or SeaTalk.
7.2 Selecting a data application
To select a data application: 1. Select a page set that includes a data application:
2. Select a page which includes a data window:
Press Select page including Digital Data application

D8464_1

D8465_1
Highlight suitable page set with Digital Data application

D9010_1

81221_4.book Page 152 Tuesday, February 28, 2006 5:24 PM
7.3 Selecting the data for display
You can either select a panel of pre-configured data or customize the application to display the data of your choice. Note: Panel selection is a local setting and will therefore only affect the individual dis-
play on which you are working.
Pre-configured data panels
The pre-configured data panels include data associated with Navigation, Waypoint, Route, Fishing or Sailing:

Panel Type

Navigation Waypoint Route Fishing Sailing
Vessel position Active waypoint TTG VMG - Waypoint Depth Cog Sog Heading

Data content

Speed Set/Drift XTE Trip Local time Sea temperature Ground wind App wind True wind VMG wind

D8950_1

81221_4.book Page 153 Tuesday, February 28, 2006 5:24 PM
To select a pre-configured data panel:
Select page including Digital Data application Move control to Digital Data window

WAYPOINT

Customize the panels
You can customize each panel by changing: The panel name. The size and number of data cells The data contained in each cell. This data can include any transducer or internally calculated navigation data that is available on NMEA or SeaTalk. Additional data includes a compass rose, a distance log and four resettable trip counters. How the data is displayed. You can control whether the data is displayed in numerical, digits, gauge or graphical format as appropriate to each data item. Note: You can also configure the data panels in this way in the Engine Monitoring and CDI applications.

Minimum range Range Discrimination Presentation Modes Scanner Control
Magnetic Sensor Waypoint Display MARPA
Variation Source Guard Zone Alarm Off centre function Wakes Target Expansion Timed TX AIS overlay
81221_4.book Page 206 Tuesday, February 28, 2006 5:24 PM

Chart Features

Cartography Chart scaling Presentation Modes Waypoints Navionics Charts on CompactFlash cards Chart of the world built in 1/64nm (if cartographic detail is available to 4000nm Head up, Course up or North up (selectable True or Magnetic) Relative or True Motion 1000 waypoints entered via cursor, lat/lon, range and bearing from present position or at boats position. 16 character name can be assigned. Waypoint symbols and groups Additional storage available on CompactFlash cards Waypoints database via NMEA A route plan may contain up to 50 waypoints. Up to100 routes can be stored in the units internal memory. Additional storage available on CompactFlash cards. SmartRoute to create a route from track history. 10 tracks with up to 1000 points in each can be stored in the units internal memory. Track optimisation reduces number of points used. Additional storage available on CompactFlash cards Programmable waypoint arrival, cross track error, anchor alarm, anchor drift, position fix/data loss warning, countdown timer and alarm clock. Own boats position in lat/lon, XTE, TTG and SOG/COG selectable. Bearing and distance to waypoint. Bearing and distance to cursor and ETA. Auto (SeaTalk/NMEA/Internal algorithm) or Manual Switch AIS symbols on/off. Specify range and display heading/ speed vectors and ROT. View detailed AIS data, safety critical target data, ALR and SRM messages. Set up a safe zone. Radar image can be overlaid on all screen charts

Waypoint Transfer Routes

Track History

Navigation information

Variation Source AIS overlay

Radar/Chart overlay

Fishfinder features
Transducer Output power: Standard transducer High performance transducer Frequency Pulse length Maximum Transmit Rate Depth: Standard transducer High performance transducer Alarms Transom-mount, in-hull or thru-hull Adjustable to 600 watts RMS Adjustable to 1000 watts RMS Dual 50 kHz and 200 kHz 100 usec to 4 msec 1580 pulses/ min at 50 ft range 3 ft (1m) to 3000 ft (1000m) 3 ft (1m) to 5000 ft (1700m) Fish alarm, fish alarm depth, shallow and deep fish limit
81221_4.book Page 207 Tuesday, February 28, 2006 5:24 PM

Data features

Panel type Data available 5 panels available. Pre-defined (Navigation, Waypoint, Route, Fishing or Sailing) or user-configured. Vessel position, active waypoint, TTG, VMG - Waypoint, depth, COG SOG, heading, speed, set/drift, trip, log, ground log, ground trip, rudder, local time and date, sea temperature, app wind, true wind, VMG wind, ground wind, XTE, compass, locked heading, waypoint data, pressure, air temperature, sea temperature, local data.

81221_4.book Page 216 Tuesday, February 28, 2006 5:24 PM
216 Dialog boxes, 9 editing, 11 Digital data application selecting a panel, 151 Display adjust lighting, 16 alarms, 27 application, 8 CDI application, 158 chart application, 45 chart detail, 86 control waypoint display, 41 current details, 50 digital data application, 151 engine monitor application, 159 fishfinder, 111 Fishfinder application, 96 MOB (man overboard), 26 object and feature details, 47 reset, 194 setup cursor autohide, 191 key beep, 192 menu, 191 soft key autohide, 191 text size, 192 show/hide cartographic features, 89 tide details, 49 waypoint groups, 42 symbols, 42 Distances, measuring, 135 DSC message, 186 DSM reset, 113 setup, 113 Dual frequency mode, 114 E EBLs, 138 bearing mode, 130 floating, 138 unfloating, 140 Echoes blind, 120 indirect, 120 multiple, 120 Edit dialog boxes, 11 routes, 68, 81
C-Series Display Reference Manual select route for editing, 68 select track for editing, 69 tracks, 68, 81 waypoint, 35 waypoint symbol or group, 37 Emergencies, man overboard, 26 Engine monitor data content, 161 overview, 159 panel type, 161 Erase information from a CompactFlash card, 21 routes, 73, 82 tracks, 73, 82 waypoint, 36 waypoint groups, 41 Extended character set, 184 External alarm, cancelling, 27 F Fast time constant, 132 Fish alarm, 188 Fishfinder 2nd echo interference rejection, 113 alarms setup, 188 A-Scope, 98 bottom fill, 104 lock, 103 structure, 96 change displayed range, 100 color gain, 116 palette, 111 cursor depth, 108 deep alarm, 110 depth cursor, 108 digit, 106, 111 lines, 108, 111 offset, 112 reading, 108 target ID, 108 display description, 96 DSM reset, 113 factors that impair performance, 98 fish alarm, 110 frequency automatic, 114 calibration, 112
81221_4.book Page 217 Tuesday, February 28, 2006 5:24 PM
Index manual, 114 dual mode, 114 single mode, 114 operating, 114 gain controls, 117 auto, 115 manual, 116 interpreting the bottom structure, 96 isolating bottom fish, 104 white line, 104 live image, 98 marking a position, 107 operating frequencies, 114 overview, 95 ping enable/disable, 113 rate limit, 113 power setting, 117 principles, 95 scroll, 111 pausing, 105 speed, 105, 111 setup, 110 display, 111 DSM, 113 transducer, 112 shifting the image, 100 SONAR interference rejection, 113 speed offset, 112 target depth ID, 111 depths, 108 distances, 108 temperature offset, 112 time varied gain (TVG), 116 trip counter reset, 113 TVG, 116 VRMs, 108, 109 white line, 104 zooming, 102 Floating VRMs/EBLs, 138 Follow route, 63 Frequency calibration, 112 FTC, 132 G Gain, 131 adjustment, 117 controls, 130 Glossary, 209, 211 GOTO function, 57 GPS, status, 189 Groundwind, in data bar, 181 Guard zones, 140 circular, 142 sector, 141 sensitivity, 188 H Hazard warnings, 27 HDG, see heading indication, 74 Head up mode, 84, 127 Heading in data bar, 180 indication, 74 vectors, 90 H-UP, 127 I Image shift, 100 Indirect echoes, 121 Integration, 1 Interference rejection, 133, 149 2nd echo, 113 SONAR interference rejection, 113 K Key beep, 192 Keyboard SeaTalk2, 186 L Land features, 89, 94 Language, 13, 184 Light sectors, 89, 94 Lighting, adjusting, 16 List AIS, 171 Live image, 98 Local chart view, 83 information, 50 Local AIS alarms, 174 Log trip, in data bar, 180 Lost AIS target, 170 M Maintenance, 193 Man overboard (MOB), 26 Managing waypoint list, 38