Distributed by

Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.
DEPTH Operation and Installation
Nautech Limited, Anchorage Park, Portsmouth PO3 5TD. England Telephone (0705) 69361 I. Fax (0705) 694642
ST50 Plus Depth Operation and Installation Handbook
Autohelm and SeaTalk are registered Trade Marks of Nautech Limited Autohelms policy of continuous improvement and updating ma); change product specifications without prior notice Copyright Nautech 1993
ST50 plus Depth Operation and Installation Handbook ST50 plus Depth Operation and Installation Handbook

Package Contents

The following items are included in the ST50 Plus Depth package: 1. ST50 Pius Depth control head 2. Fixing studs (2 offI 3. Thumb nuts (2 oftI 4. Fitting template 5. Power cable 6. Depth transducer (through hull) with 14m(45ftI of cable 7. Control head cover 8. Operation and Installation handbook 9. Worldwide Setice Cenb-e handbook 10. Warranty document 11. Security code sticker

I ! ! ! / ! I 1 I

Plus Depth Operation and Installation Handbook

Contents

Introduction... Chapter 1: Control Head Installation... 1.1 Sing... 1.2 Mounting Procedure... 1.3 Power Supply (stanchalone operation).. t 1.4 Power Supply (SeaTalk operation). ;.. f 1.5 Connection of Separated Instruments.. ; 1.6 Ring Connection... I 1.7 Connection to SeaTalk Compatible Autopilots. I Chapter 2: Transducer Installation.. 2.1 Connection to the Control Head.. m 2.2 Transducer Selection.. 2.3Transducer Installation.. Chapter 3: Fault Finding and Maintenance.. 3.1 FaultFinding... 3.2 Maintenance... Chapter 4: Operation... 4.1 DepthKey... 4.2AarmKey... 4.3 Dffset Key.. 4.4 Reset Key.. 4.5 Display Contrast... Chapter 5: CODE Lock Security.. Chapter6: Calibration... 6.1 initial Calibration.. 6.2 Intermediate Calibration.. 6.3 Extended Calibration.. Chapter 7: General Specification..

a c J 13.15.35

ST50 plus Depth Operation and Installation Handbook

Intmduction

The ST50 Plus Depth is a SeaTalk compatible, multifunction instrument that employs a powerful echo sounder to give excellent performance over a wide range of sea conditions. Deep, shallow, anchor watch alarms can be set to provide visual and audible warnings when the water depth reaches selected thresholds. The ST50 Plus Depth can be configured to operate as a master unit or a dedicated repeater. Al settings are stored in permanent memory and retained even when the power source is disconnected. The ST50 Plus Depth also incorporates a securii feature to protect instruments mounted in vulnerable areas such as the cockpit, helm or mast. Thank you for purchasing an Autohelm product May we take this opportunity towishyouyearsoftroublefreeoperation.
ST!50 Plus Depth Operation and htaliation

Handbook

Chapter 1: Confrol

Head Installation

Chapter i: Coniroi i-&j ins&&h
r llOmm(4.33in) r, 38.75mm (1.5in)

1.1 Sing

The ST50 Plus Depth is designed for above or below deck installafion where it is:

l l l l l

Easily readable by the helmsman Protected against physical damage At least 230mm (gin) from a compass At least 5&m (20in) from radio receiving equipment Accessible from behind for ease of installation and cable running

Caution: To prevent moisture forming on the display window, the ST50 Plus Depth breathes through a small vent in the cable boss. Iherefore, the control head must be sited where the rear case is protected from contact with water.

_.-.- ___^_

._.- ____,_.- -- -.
, 4 , ST!% plus Depth Operation and Installation Handbook ChaMer 1: Control Head Installation

Bracket Mounting

The ST50 Plus Depth can, as an alternative, be bracket mounted using the Autohelm Mounting Kit.
1 Cable boss 2 Fiiing studs 3lhumb nuts 4Gashet
1.2 Mounting Procedure 1. Make sure that the selected location is clean, smooth and flat.
2. Apply the self-adhesive template (supplied) to the selected location and mark the centres for the fHing studs (2) and the cable boss (1). 3. Drii two 4mm (5/32in) clearance holes for the fixing studs (2) through the bulkhead. Remove the template. 4. Cut the clearance hole for the cable boss (1) using a 50mm (2in) diameter cutter. Pass the SeaTalk cable and transducer tails through the cable-boss (1) clearance hole.

Flush Mounting

A flush mounting kii is available for installations where a flush mount is required or more desirable. Full installation instructions are provided with the kit.
5. Screw the two fixing studs (2) into the control head. 6.
7. Assemble the contiol head to tie bulkhead and secure from behind using the thumb nuts (3). Note: The rear case is fitted with a foam gasket to form a water-tight seal between the instrument and the selected installation face. Under no circumstances must silicone greases be applied to this gasket as an additional method of sealing-the silicone will expand and distort the rear case.

e--m._

--._-___
ST50 Plus Depth Operation and ImtaUation Handbook
Chapter I: Control Head Installation
1.3 Power Supply (stand-alone operation)
1.5 Connection of Separated lnsttuments
Separated instruments can be connected using one of the range of SeaTalk Extension Cables. These cables are supplied with a SeaTalk connecMitted to each end. Ajunction boxcan be used tojointhecableifitis cutforeasier routing or shortening. If preferred, any 2 core, screened cable conforming the following specifiMion may be used instead of the SeaTalk cable.
22 AWG, 2 core screened cable with a minimum copper area of 0.5mmz.

1. Connect the 2m (6ft.l power supply cable directly to the distribution W. 2. Cut the cable to length and connect the red wire to the +12V terminal and screen to the OV terminal. 3. Cut back and insulate the yellow wire. 4. Protectthe circuiiwith a SAcircuiibreaker. Longer runs to the power supply can be made using the 9m (3OftI SeaTalk Extension Cable D131).

Junction box rYeUowl

1.4 Power Supply (SeaTalk

operation)

Screen J L Red J
All instmrnents in a SeaTalk system receive power and information from the SeaTalk bus. Each instrument has two SeaTalk connectors (3 pin) on 15Omm (6in) tails. To supply power and information to the instrument simply plug adjacent tails into the ST50 Plus Depth tails.
:s. To transducer ,:: :. 1,. :.l.,

SeaTalk tails

SeaTalk
Chapter 2: Transducer installation

1.6 Ring Connection

Installations with large numbers of instruments on a SeaTalk bus may require a second ringmain connection to the power supply breaker to prevent excessive voltage drops. Refer to the foflowing list to determine whether a second ring main is necessary.
Chapter 2: Transducer Installation
2.1 Connection to the Control Head
The depth transducer is supplied, as standard, with a through hull fling and 14m (45ftI of cable. The cable is equipped with a SeaTalk connector that plugs into a control head connector.

Cable run upto 10m (3%)

Single connection: Second connection: Single connection: Second connection: 13 instruments maximum 26 instruments maximum 7 instruments maximum 13 instruments maximum
Cable run upto 20m (66ft)
The second ringmain should be connected to the spare lead on the last instrument in the chain and directed back to the circuit breaker.
1.7 Connection to SeaTalk

Compatible Autopilots

If the installation includes a SeaTalk compatible Autopilot the ST50 instru ments may be connected to the SeaTalk bus at any point. No independent connection to the 12V power supply is necessary as the instruments receive power from the Autopilot course computer.

2.2 Transducer Selection

The type of depth transducer used is governed by the hull material. The following list shows the appropriate transducer for hull type.

To autopilot SeaTalk B U S Connection To any further ST50 Instruments or Autopilot Control Units ,,u-

Transducer

Hull Material GRP (Glass Reinforced Plastic), Steel and Aluminium Wocd GRP (Glass Reinforced Plastic), Steel and Aluminium
ZO91 Through Hull Plastic: Z118 Through Hull Bronze: 2120 Retractable througb hull:
2.3 Transducer Installation
All depth transducers are supplied with detailed installation and maintenance instructions. These instructions, together with the following notes, should be read thoroughly before attempting to install the transducer.
ST50 plus Depth Operation and lnstallatin Handbook
For accurate depth readings the transducer should be sited within the

shaded clear flow areas.

Cabling
1 Sail 2 Plmningfxnw 3 Displacementpower The transducer should also:
1. Run the cable back to the control head. Note: Avoid fluorescent lights, engines, radio transmitting equipment etc. as these may cause interference. Also, keep the transducer cable clear of the bilge and secure at regular intervals. 2. Fit the transducer and instrument cable connectors together. To lock the connectors, push and rotate the ring on the transducer cable connector towards the control head connector.
be ahead of the propeilers (loo/o W.L. length minimum) be at least 150mm (6in) away from the keel (ideally ahead of the keel if a sailing yacht) be as near as possible the centreline of the vessel be clear of other throughhull fttings or projections have sufficient clearance inside the hull to fit the nut have 1OOmm (4it-r) of headroom to allow for withdrawal within l@of the vertical, forward, aft and athwart shiis.

l l l l

plus Depth Operation and Installation Handbook
Chapter 3: Fault Finding and Maintenance
Chapter 3: Fauit Finding and Maintenance

3.1 Fault Finding

All Autohelm products are, prior to packing and shipping, subjected to comprehensive test and quality assurance programmes. However, if a fz arises with the ST50 Flus Depth, the following table will help to identify the probable cause and provide the most likely cure.
Fault Instrument display blank. Cause No supply. Action Check supply. Check cabling and security of SeaTalk connectors. Check fuse/breaker. Return unit for repair Enter correct code number. Check securii of SeaTalk connectors. Remove instruments one by one to isolate faulty unit. Check security of SeaTalk connectors between functioning and nonfunctioning instruments. Check cabling and securii of transducer connector.
Instrument displays CODELOCK set, ENTER CODE. No exchange of information between SeaTalk instruments tie, illumination levels).

The CODE Lock feature has been set. SeaTalk cabling problem.
SeaTalk Failure of a group of instruments in SeaTalk cabling/connector chain. problem.
Depth reading continuously flashes @e;th greater than 3 Depth reading flashes while underway.
Transducer cable/connector problem.
Normal reading will Aereated water, boat wakes, propellor wash return when clear of etc. disturbed water. IX

_._.,,.

ST50 Plus Depth Operation and installation Handbook

Chapter 4: Operation

ChGptX 4: OptHSkBi

lnslrument

Certain atmospheric conditions may cause condensation to form on the control head window. This will not harm the unit and can be cleared by increasing the illumination setting to Level 3. Chemical and abrasive materials must not be used to clean the control head; if it is dirty, clean with a soft, damp cloth. As it leaves the factory the ST50 Plus Depth is set with:
depth units in feet transducer off set set to 0 feet shallow alarm set to 10 feet deep alarm set to 100 feet low anchor alarm set to 50 feet high anchor alarm set to 50 feet
Refer to the Installation and Maintenance instructionssupplied with the transducer.
These settings can be changed in calibration, Chapter 6. When the unit is poweredup for the first time water depth will be displayed. Note: IfduringalOsecondperiodnovec~s~ereceived,t flash(ithedepthisgreatertban1OOftIaftera10seconddelaytoindiiate that the display is not being updated and that the currently cfrspkryedvalue was the last valid echo.
Examine all cables for chafing or damage to the outer shield and, where necessary, replace and resecure.

Advice

For advice, or further information regarding the instajlation of this product, please contact the Autohelm product Support Department or your own National Distributor.

-16. *,

ST50 Plus Depth Operation and lmtanation.-._ Handbook Chapter 4: Operation

.___-.

._.-.-.-__.___._
Depth Key Notes Minimum Depth
Minimum depth can be reset by pressing RESR: Minimum depth returns to current depth after 8 seconds.

Display Fathoms

Contrast
The display contrast is automatically adjusted when the tights are turnedon. Whentheunksofmeasurearesettofeet,fathomswillbedisplayxdbefore minimum depth.

MINIMUM MPll I

Aiarm iioies Shallow Alarm
The shallow alarm has priority over all alarms. The shallow alarm will sound until it is silenced, however, the shallow alarm legend continues to flash until the depth rises above the setthreshold.

Deep/Alarm

The deep alarm is triggered when crossing the set threshofd going from shallow to deep and deep to shallowwaters. Unless it is silenced, the deep alarm sounds for 30 seconds.

Anchor Alarms

The anchor alarms provide visual and audible warningswhen the water reaches critical low or high levels when the vessel is anchored. These alarms can be silenced, however, the visual alarm will continue to ffash until a safe water depth has been reached.

Silencing Audible Alarms

I MEP ALARM
Audible alarms can be silenced by pressing any key.
Enabling and Disabling Alarms
Afl alarms can be disabled. For further details, please refer to the calibration section.

ANCHOR LOW ALARM

ANCHOR HIGH AU\RM
ST50 J&s Depth Operation and installation Handbook

Chapter 4: Operaibn

A 7 ncLJ Ltd. -r.u VII~GC nGy

neset Key

Offset Key Notes
The off set value can be positive or negative: depih measured from the keel is negative and depth to the waterline positive. The offset display will return to water depth 8 seconds after the last key press

Reset Key Notes

This feature allows the depth uniis to be switched between feet and me&es. However, the units can only be toggled when the current water depth is displayed.

m---._._._.

,._ -._

-._.---.

ST50 Plus Depth Operation and lnstaiiation Handbook
Chapter 5: CODE Lock Security

4.5 Display Contrast

The contrast can be adjusted to achieve optimum legibility at any angle.

-Decrease

Cnapter 5: CODE Lock Security
The ST50 Plus range incorporates an anti-theft feature called CODE Lock. Designed to protect individual instruments or complete systems ir vulnerable areas, CODE Lock is a four digit number that you programmc into the permanent memory of a selected master instrument. Note: A master instrument is a digital unit on which the code number can be entered, and then, if part of an integrated system, transmitted to other ST50 Plus instruments. This facility means that, should a CODE Locked instrument be removed from a vessel without the owners permission, it cannot be operated without the four digit security number. CODE Lock can be used in one of three modes:

-contrast

1. Momentarily press DEPlH and ALARM together. 2. Press OFFSET or RESET to increase or decrease the contrast setting (the range being between 1 and 15). Note: A high setting will suit installations where the control head will be viewed from abow. 3. Press DEPTH and ALARM together momentarily to store the contrast setting.

Mode 1: Off

As it leaves the factory CODE Lock is set to off. In this mode the instrument will operate normally when it is switched on, however, the unit will not be protected by the anti-theft feature.
Mode 2: CODE Lock Once-Only Entry (page 25)
This mode is designed for systems with a digital ST50 plus instrument in -a safe, belowdecks location. This instrument can then be used as a master to enter the four digit code number, and automatically transmit the code to all the instruments in the system when the power is switched on. The advantage of this mode is that, with the master safely below deck, code entry via the keypad is a onceonly operation on installation.

Once CODE Lock is set the system will operate normally as soon as the power is switched on. In other words, the CODE Lock securii number is invisible.
Once Only Entry In the Power& mode, the ST50 Plus is configured so that you have to enter the four digit number on the master instrument every time the system is switched on. Until this number is entered the instrument(s)willnotoperate. This mode is particularly useful when you are unable to position a master instrument below decks and, therefore, all the vessels valuable instrlt mentation is left in a vulnerable area.

Action 11 Display Shows

Press and DEPTH and ALARM together for CAL after 2 seconds and 4 seconds VER X.X after 4 seconds Press DEPTH twice 4 seconds after CODELOCK Cal. Off Press ALARM Press OFFSET or RESET to select first number Press ALARM to accept number Press OFFSET or RESET to select second number Press ALARM to accept number Press OFFSET or RESET to select third number Press ALARM to accept third number Press OFFSET or RESET to select fourth number Press ALARM to accept code Leave PWR ON? flashing for 10 seconds To save code, press DEPTH and ALARM together for 2 seconds CODELOCK Cal. Off ENER CODE I I - --_ 1___ l,- 12__ 1 2-12312 3-l FWR ON? CODELOCK Cal. set Normal operation, eg. depth display Tlvx
Should a CODE Locked instrument be removed from the system, it will not operate until the correct four digit security number is entered or received. If your selected master instrument fails for any reason, the security code number can be entered via another ST50 Plus instrument in the system. However, until another instrument is set as a master or the existing master is replaced, the security code will have to be entered every time the system is switched on. Note: A warning sticker is provided with each instrument. If you have set Code Lock, position this warning sticker in a prominent location to deter potential thieves.

13 Press ALARM

If you do not exit CODELOCK Cal. set within 10 seconds, the display will change to CANCEL CODE. You now have the option of cancelling the code, by pressing ALARM to return to the _ _ __ display, or exit as described in action 15 above. Your Code Number For future reference, enter your chosen code number in the following box.
Setting Up the Security Code
When the ST50 Plus Depth is switched-on for the first time the security feature is set to off. To turn the CODE Lock feature on, proceed as follows:
For obvious reasons, please store this handbook in a safe place. Operation Once only CODE Lock entry is invisible once it has been set.
.,. _._._-_-__-. - , -&PA ~._ -_ _- _-._
ST50 plus Depth Dperation

andlnstallation

Chapter 6: Calibration
On i;ower-Up Action 7 Display Shows
As it leaves the factory the ST50 flus Depth is set to dispfay depth u&s in

feet. These settings, together and other navigational features, can be
Press and DEPTH and ALARM together for CAL after 2 seconds and VER X.X after 4 seconds 4 seconds Press DEPTH twice 4 seconds after CODELOCK Press ALARM Cal. Off CODELOCK Cal. Off ENTER CODE I I - - - 1___ 1~- 12 __ 1 2-3- PWR ON? CODELOCK Cal. set
changed (e.g., Feet to Metresjas described in this section.
Press OFFSET or RESET to select first number Press ALARM to accept number Press OFFSET or RESET to select second number Press ALARM to accept number Press OFFSET or RESET to select third number Press ALARM to accept third number Press OFFSET or RESET to select fourth number Press ALARM to accept code Press ALARM within 10 seconds To save code, press DEPTH and ALARM together for 2 seconds
Normal operation, eg. depth display T11Zl
If you do not exit CODELOCK Cal. set within 10 seconds, the display will change to CANCEL CODE. You now have the option of cancelling the code, by pressing ALARM to return to the __ _ _ display, or exit as described in action 15 above. Your Code Number For future reference, enter your chosen code number in the following box.
For obvious reasons, please store this handbook in a safe place.

Operation

When the unit is powered on you are prompted to enter the code number. To enter the number, carry out actions 4 to 12 and press ALARM.

6.1 Initial Calibration

Initial Calibration Notes Alarms
The shallow, deep, low anchor, high anchor and offset displays can be adjusted using the OFFSET and RESET keys. The ALARM key is used to enable/disablethe alarms. units Alternating between feet and metres is achieved by pressing RESIX

Exii Initial Calibration

To exit initial calibration and store the new settings, press DEPTH and ALARM together for 2 seconds.

SHALLOW AlAf3M

. _. _ _
ST60 plus Depth Operation and Installation Handbook Chapter 6: Calibration 3:
Intermediate Calibration Notes RepeaterMode
Repeater mode allows the ST50 Hus Depth to repeat speed related data already on the SeaTalk bus. There are two settings: O=disabled and 1 =enabled.
lnitialcalibrationcannotbeaccessedwheniheunitisconfiguredasarepeater.
Exit Intermediate Calibration
To exii intermediate calibration and store the new settings, press DEPTH and ALARM for 2 seconds.

SECURITY

-.- - -.ST50 Plus Depth Operation and installation Handbook Chapter 6: Calibration

.~ -.- ----..

._. -. __ _.____ -.__._.
Extended Calibration Notes

All of the extended calibration screens are adjusted usingtbe WFSETand/or RESET keys.

Calibration

Calibration allows you to protect your selected settings. When calibration is enabled the initial and intermediate calibration settings cannot be modified. CAL0 = Calibration locked, i.e. no access CAL 1 = Calibration unlocked, i.e. normal access Once locked, calibration can be unlocked by entering extended calibration and selecting 1, calibration unlocked.

Depth Damping

Depth damping adjusts the rate atwhichfhe display is updated. The default setting is 4 seconds, however, the selectable range is 1 to 15.

Boat Show

The Boat Show mode is a dealer demonstration program only. Under no circumstances must this program be engaged when this unit is installed onboard your vessel.
Exii Extended Calibration
To store the extended calibration settings, press DEPTH and ALARM for 2 seconds.

DEPTH DAMPING

eration and lnstailation
Chapter 7: General Specification
Dimensions: Power supply: Power consumption: Temperature range: Depth: Shallow alarm: Deep alarm:
llOxllOmm(4.33x4.33inI lOtol6V 50ma (normal) lOOma WJfnination on)

0 to 70 deg.C

Offset:
Anchor alarm: Minimum depth function: Units: Damping: Repeater capability: Illumination:
Oto6OOfeet(Oto18Ometres) 3 to 33 feet (1 to 10 metres) 1Oto4OOfeet(3to12Ometfes) -9.9 to 9.9 feet (4 to 4 metres)
Oto6OOfeet(Oto18Ometres) Reset on powerup Software programmable feet/lathoms or metres

1 to 15 seconds

Software programmable 3levelsplusoff

11S 24v, 32v systems 16 - 44 volts 80W 11W diameter: 75.9 x 16 33.4kg (73.7lbs) 4 stud 10kW 72" open array 15m standard (25m option) -10C to +55C -10C to +70C up to 95% CFR46 72nm 9410 +/-30 MHz 10 kW 8 (auto/target expand) 70 seconds <2.5 seconds 1.horizontal <-25dB 24rpm 60MHz 12/3/0.7/0.5MHz
72nm 9410 +/-30 MHz 10 kW 8 (auto/target expand) 70 seconds <2.5 seconds 1.horizontal <-22dB 24rpm 60MHz 12/3/0.7/0.5MHz
Pathfinder SL72 systems Each SL72 Plus system consist of a SL72 Plus display and 2D antenna E52026 SL72 Plus system with 10m cable E52027 SL72 Plus system with 15m cable with built in Raychart E52041 SL72RC Plus system with 10m cable E52042 SL72RC Plus system with 15m cable Pathfinder displays Combine with any Pathfinder scanner to create a radar system. Pathfinder radar displays with hsb2 E52031 RL70 Plus 7" monochrome LCD E52033 RL70C Plus 7" color LCD E52037 RL80C Plus 10.4" color LCD E52039 R70 Plus 7" monochrome CRT E52035 R80 Plus 10" monochrome CRT with built in Raychart and hsb2 E52032 RL70RC Plus 7" monochrome LCD E52034 RL70CRC Plus 7" color LCD E52038 RL80CRC Plus 10.4" color LCD E52040 R70RC Plus 7" monochrome CRT E52036 R80RC Plus 10" monochrome CRT

4.15 in 8.76 in 2.95 in

9.56 in

10.8 in 16 in

8.1 in

8.5 in

8.9 in
16.8 in 51.4 in (48") 75.5 in (72")

11.65 in

48" AND 72" OPEN ARRAY SL72 PLUS, SL70 PLUS AND RL70 PLUS

8.76 in 6.04 in 8.9 in

R70 PLUS

5.95 in 18.4 in

7.3 in 23.6 in
18" AND 24" SL70C PLUS AND RL70C PLUS

5.47 in 11.26 in 3.82 in

Pathfinder Plus SL series radar displays E52043 SL70 Plus 7" monochrome LCD E52045 SL70C Plus 7" color LCD with built in Raychart E52044 SL70RC Plus 7" monochrome LCD E52046 SL70CRC Plus 7" color LCD Pathfinder radar scanners M92650 2D 2kW 18" radome with 15m cable M92652 4D 4kW 24" radome with 15m cable T52001 5S 4kW 48" open array with 15m cable T52013 7S 4kW 72" open array with 15m cable T52012 9S 10kW 48" open array with 15m cable (24v, 32v DC only) T52014 11S 10kW 72" open array with 15m cable (24v, 32v DC only)

12.3 in

Optional scanner cables M92728 15m pedestal cable E55017 15m Pathfinder open array radar arch cable (2 pc) M92705 25m pedestal cable M92699 Pathfinder extension cable (5m) M92700 Pathfinder extension cable (10m) E56001 Pathfinder 5m cable radome M92692 Pathfinder 10m cable for 2kW radome only M92668 Pathfinder 15m cable-radome M92669 Pathfinder 25m cable-radome Radar accessories E12102 Smart heading sensor Radar/hsb2 cables R55001 hsb2 cable (1m) R55002 hsb2 cable (3m) R55003 hsb2 cable (6m) R55004 hsb2 cable (10m) E55010 hsb2 cable (20m) E55040 hsb2 Y cable

RL80C PLUS

10.9 in 14.2 in

10.4 in

11.4 in

R80 PLUS

11.6 in

Navigation Aids

Pathfinder Plus Raycharts
GENERAL SL520 Plus Power: Nominal voltage (volts DC) 12v, 24v, 32v systems Absolute voltage range (volts DC) 10.7 - 44 volts Power consumption (typical) watts 10W (fully backlit) Physical: Overall dimensions (WxHxD) inches 8.8x8.07x2.9 Product weight kg (lbs) 1.2kg (2.6lbs) Mounting methods bracket or panel Control type(s) 11 defined, 4 soft keys Cursor (context sensitive) trackpad Color/mono mono Display size and type 7" FSTN LCD Display resolution 320x240 (1/4 VGA) Display lighting (contrast) 100 levels (adjustable) Connections: NMEA input (0183) (2) NMEA output (0183) SeaTalk 2 hsb Cartography 2x C-MAP NT (+) Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range -10C to +50C Non operating temperature range -10C to +70C Humidity up to 95% Waterproofing standard CFR46 KEY FEATURES Range scales 1/64 to 4000nm Range options 20 scales Max. detail of background map 150nm Head Up/North Up/Course Up True/Magnetic (variation source) (auto/manual) Waypoints (1000) Waypoint name 16 character Waypoint storage database/user cartridge Waypoint entry graphical/manual Manual waypoint entry LatLon/BrgRng/TDs Waypoint transfer via SeaTalk/NMEA PC Waypoint transfer (via NMEA WPL sentence) Routes (20) Route name 16 character Route storage database/user cartridge Waypoints per route up to 50 Tracks (5) Points per track 750 Track interval time/distance Smart Route (track to route) Alarms arrival/XTE/anchor/fix Timers alarm clock/countdown Ruler Navigation information position/XTE/SOG/COG Navigation predictions TTG/ETA GOTO/Follow functions waypoint/cursor/route Tidal information supported Sunrise/Sunset predictions (via chart) Man OverBoard (MOB) GPS FEATURES Type*** display and Raystar 120 Beacon Differential Ready (auto/man tune) Filters 3 levels for COG/SOG Geodetic datum WGS-84 (or local) Position correction ADDITIONAL FEATURES AND DISPLAY OPTIONS Radar/Chart synchronization (with radar) local Radar/Chart Overlay (with radar) Course Deviation Indicator (rolling road) Bearing Deviation Indicator Data Boxes split screen or 6 boxes Ship's log Chart presentation full or half screen Raychart with full function radar* Raychart with full function fishfinder** SL530 Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit) 8.8x8.07x5.98 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 7" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT (+) -10C to +50C -10C to +70C up to 95% CFR46 1/64 to 4000nm 20 scales 150nm (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart) display and Raystar 120 (auto/man tune) 3 levels for COG/SOG WGS-84 (or local) local split screen or 6 boxes full or half screen SL631 Plus 12v, 24v, 32v systems 10.7 - 44 volts 30W (fully backlit) 11.5x11.4x5.5 5.8kg (12.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 10" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT (+) -10C to +50C -10C to +70C up to 95% CFR46 1/64 to 4000nm 20 scales 150nm (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart) display and Raystar 120 (auto/man tune) 3 levels for COG/SOG WGS-84 (or local) local split screen or 6 boxes full or half screen Raychart 520 Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x2.9 1.2kg (2.6lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 100 levels (adjustable) (2) 2x C-MAP NT (+) -10C to +50C -10C to +70C up to 95% CFR46 1/64 to 4000nm 20 scales 150nm (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via hsb2/SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart) Raychart 530 Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit) 8.8x8.07x5.9 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 7" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT (+) -10C to +50C -10C to +70C up to 95% CFR46

22 - 25

RayTech Navigator control raster and vector chart transparency (raster charts are "quilted" together") (requires hsb2 Kit or Pathfinder PC Kit) (requires Fishing Pro or subscription) (requires Fishing Pro or subscription) (SeaTalk or NMEA compass input recommended) (auto/manual) (requires Sail Racer or Fishing Pro) (requires Sail Racer) (unlimited) 16 character via hsb2 or SeaTalk (unlimited) 16 character (requires Sail Racer) up to 50 (unlimited) unlimited time intervals user defined databoxes time to go/estimated time of arrival waypoint/cursor/route optional requires Pathfinder PC or hsb2 kit and any hsb2 compatible Pathfinder Plus radar system (2) (2) auto/manual auto/manual auto/manual on/off on/off (10 targets) (2) requires Pathfinder PC or hsb2 kit and any hsb2 compatible Pathfinder Plus radar system auto/manual auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) auto/manual

RAYTECH NAVIGATOR

RayTech software kits E83025 Raytech Navigator E83027 Raytech Sail Racer* E83026 Raytech Fishing Pro* E86014 Pathfinder PC Kit* * Includes RayTech Navigator RayTech accessories E86019 hsb2 PC interface kit (part of Pathfinder PC kit) E85001 PC/Seatalk/NMEA interface box (part of Pathfinder PC kit) E86008 C-MAP USB chart reader

RAYTECH SAIL RACER

hsb2 PC INTERFACE KIT RAYTECH FISHING PRO
PC/SeaTalk/NMEA INTERFACE BOX
(customisable) via hsb2 via hsb2 Pathfinder panel or windows

RAYTECH PATHFINDER PC

C-MAP USB CHART READER
RNS1500 15" Daylight Viewable Monitor
GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Physical: Overall dimensions (WxHxD) inches Mounting methods Defined control(s) Color/mono Display size and type Display resolution Lighting Connections: Analog VGA input Digital video (DVI) input Composite video input Audio input Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range (nominal ambient) Non operating temperature range Humidity Waterproofing standard RNS1500 Monitor 12v, 24v systems 10.7 - 32 volts 16.3x13x6.3 bracket or panel 3 defined buttons Color 15" TFT LCD 1024x768 (XGA) 64 levels -10C to +50C -10C to +70C up to 95% CFR46
RNS1500 Monitor E02009 RNS1500 monitor E02014 RNS1500 monitor with touch screen
RayTech Product comparison chart
PRODUCT FEATURES RayTech Navigator advanced charting and navigation application DataTrak time based graphs Polar data collection and analysis Route optimization Race analysis tools for precise instrument calibration, start, wind trends, performance monitoring, layline and navigation analysis 1 year advanced weather subscription 1 year satellite plankton and sea surface temperature subscription Engine monitor display* hsb interface card SeaTalk interface

2.59 in

1.41 in

2.64 in

TRANSDUCER POD
SPEED AND DEPTH TRANSDUCERS (TYPICAL)

3.97 in

3.3 in

LONG ARM WIND TRANSDUCER

ST290 instruments T22071 ST290 system pack, comprises: ST290 Graphic display, ST290 data processing unit (DPU), ST290 speed pod, ST290 depth pod, ST290 system manual. Note: compatible speed/depth transducer must be ordered separately. M78712 through-hull speed transducer (plastic) M78713 through-hull depth transducer (plastic) (see also choice of speed/depth transducers for ST60)
E22068 E12102 E22056 E22057 E22059 E22061 E22060 E22062 E22064 E12094 E12104 E22063
ST290 active long arm wind transducer Smart heading sensor ST290 Data display ST290 Graphic display ST290 wind display ST290 CH/VMG display ST290 compass display ST290 rudder angle display ST290 MOB keypad ST290 pilot keypad (button) ST290 pilot keypad (rotary dial) ST290 digital remote keypad
ST290 accessories E25036 SeaTalk2 cable: 400mm plug to plug E25037 SeaTalk2 cable: 400mm plug to wire E25038 SeaTalk2 cable 10m plug to plug E25039 SeaTalk2 cable: 10m plug to wire E25040 SeaTalk2 cable: 1m plug to plug E25041 SeaTalk2 cable: 1m plug to wire E25042 SeaTalk2 cable: 3m plug to plug E25043 SeaTalk2 cable: 5m plug to plug E25044 SeaTalk2 cable: 20m plug to plug E25045 SeaTalk2 cable plug boots (Pack of 5)
E25046 E25047 E25048 E25049
SeaTalk2 -ST junction box blanking plugs SeaTalk2 cable: 200m reel SeaTalk2 bus terminator SeaTalk2 junction box - 5 way

ST60 Instruments

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) mA Physical: Overall dimensions (WxHxD) inches Mounting methods Control type(s) Display size and type Maximum character size Display lighting Connections: NMEA input and output (0183) SeaTalk PC (RS232) and Raytech interface option Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard DISPLAY PAGES Speed data Speed range (knots) Log range (nm) Trip range (nm) Speed units Water temperature Depth data Depth range (m) Depth offsets Depth alarms Depth units Wind speed data Wind speed range (knots) Wind angle data Wind angle range Wind alarms Wind units (wind only) Heading data Heading offset and variation Heading alarms Locked compass heading option Timers Transducer alignment and calibration Man OverBoard (MOB) repeater Rudder angle indication ADDITIONAL FEATURES Speed 12v systems 10 - 16 volts 45mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 92mm segmented LCD 36.4mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46 current/max/average 0 to 60kts 0 to 99999nm 0 to 999nm knots/kph/mph -10C to +40C stop/lap/countdown manual/via SOG vel. made good (VMG) SOG via GPS autopilot status 1/100knot resolution DISPLAY OPTIONS Low power indication Adjustable display response time System option supplied with transducer Round Analog repeater option Clip on bezel option ST60 round flush mount Depth 12v systems 10 - 16 volts 45mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 92mm segmented LCD 36.4mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46 Wind and CH Wind 12v systems 10 - 16 volts 65mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 34mm segmented LCD 13mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46 Compass 12v systems 10 - 16 volts 65mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 34mm segmented LCD 13mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46 Rudder Angle 12v systems 10 - 16 volts 45mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46 manual (pointer) ST60 round flush mount Tridata 12v systems 10 - 16 volts 45mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 92mm segmented LCD 19mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46

2.4 in

27.0 in

2.76 in

ST60 LONG ARM WIND TRANSDUCER

ST60 RUDDER REFERENCE

ST60 AND ST40 COMPASS TRANSDUCER

10.6 in

ST60 AND ST40 WIND TRANSDUCER

3.32 in

3.5 in

ST40 Instruments

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) mA Physical: Overall dimensions (WxHxD) inches Mounting methods Control type(s) Display size and type Maximum character size Display lighting Connections: NMEA input and output (0183) SeaTalk PC (RS232) and Raytech interface option Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard DISPLAY PAGES Speed data Speed range (knots) Log range (nm) Trip range (nm) Speed units Water temperature Depth data Depth range (m) Depth offsets Depth alarms Depth units Wind speed data Wind speed range (knots) Wind angle data Wind angle range Wind alarms Wind units Heading data Heading offset and variation Heading alarms Locked compass heading option Alignment and calibration Man OverBoard (MOB) repeater DISPLAY OPTIONS Low power indication Adjustable display response time System option supplied with transducer Clip on bezel option Replace boat speedo Speed 12v systems 7.5 - 16.5 volts 25mA 4.9x2.75x1.5 surface or bracket 3 backlit buttons 88mm segmented LCD 28mm 3 levels plus off option -10C to +70C -10C to +70C up to 95% CFR46 current/max/average 0 to 99.9kts 0 to 99999nm 0 to 999nm knots/kph/mph -10C to +40C manual/via SOG (4 colorways) Depth 12v systems 7.5 - 16.5 volts 30mA 4.9x2.75x1.5 surface or bracket 3 backlit buttons 88mm segmented LCD 28mm 3 levels plus off option -10C to +70C -10C to +70C up to 95% CFR46 current/min 0.8 to 130m (400') keel/waterline/transducer shallow/deep/anchor meter/fathom/feet manual (4 colorways) Wind 12v systems 7.5 - 16.5 volts 25mA 4.9x2.75x1.5 surface or bracket 3 backlit buttons 88mm segmented LCD 17mm 3 levels plus off option -10C to +70C -10C to +70C up to 95% CFR46 apparent/true 0 to 60kts apparent/true 180 port and starboard high true wind speed knots/m/s manual (4 colorways) Compass 12v systems 7.5 - 16.5 volts 20mA 4.9x2.75x1.5 surface or bracket 3 backlit buttons 88mm segmented LCD 17mm 3 levels plus off option -10C to +70C -10C to +70C up to 95% CFR46 current/locked magnetic/true off course manual (4 colorways) Bidata 12v systems 7.5 - 16.5 volts 35mA 4.9x2.75x1.5 surface or bracket 3 backlit buttons 88mm segmented LCD 28mm 3 levels plus off option -10C to +70C -10C to +70C up to 95% CFR46 current/max/average 0 to 99.9kts 0 to 99999nm 0 to 999nm knots/kph/mph -10C to +40C Current/min 0.8 to 130m (400') keel/waterline/transducer shallow/deep/anchor meter/fathom/feet manual/via SOG (4 colorways) -

ST40 transducers E26007 transom mount depth transducer E26008 through-hull depth transducer, plastic E26005 transom mount speed transducer E26009 through-hull speed transducer, plastic E26006 transom mount triducer SeaTalk cables D284 1m cable D288 20m cable D285 3m cable D286 5m cable D287 9m cable Dway junction box D188 ST50 female adapter cable D187 ST50 male adapter cable

Autopilots

Tiller, Wheel and Packaged Pilots
GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (standby) mA Physical: Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Display size and type Maximum character size Display lighting Connections: NMEA input (0183) SeaTalk Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard KEY FEATURES Steer to compass Steer to wind Steer to navigation info (waypoint or route) Waypoint advance feature Autotack Selectable tack angle Autotrim, seastate Windtrim Autoadapt (for Northerly/Southerly environments) User calibration Compass deviation correction Gain Damping Response Adjustable turn rate Alarms Diagnostic alarms Rudder angle indication Direction to steer arrows ADDITIONAL FEATURES Predefined data displays Customisable data displays Repeat instrument and navigation data on pilot Man OverBoard (MOB) repeater DRIVE OPTIONS Standard drive Optional drives Thrust kg (lbs) with standard drive Thrust kg (lbs) with optional drive Stroke Maximum recommended boat displacement (std drive) Maximum recommended boat displacement (optional) SYSTEM OPTIONS Remote control option Multiple control displays Extra loud external alarm Autopilot status repeated on instruments External compass Rudder Reference option *Sterndrives designed to fit Volvo, Mercruiser etc. ST1000 Plus/ST2000 Plus Tiller Pilots 12v systems 10 - 15 volts 40mA 17.7x2.9x3.7 1.53kg (3.4lbs) reversible port or starboard 6 buttons 45mm segmented LCD 9mm 3 levels plus off -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (9 levels) (9 levels) (5 to 20/second) off course (3 pages) integral (drive/display/compass) ST1000+: 57kg (125lbs) ST2000+: 77kg (169lbs) 254mm (10") ST1000+: 3000kg (6600lbs) ST2000+: 4500kg (10000lbs) optional ST4000T/ST4000T GP Tiller Pilots 12v systems 10 - 15 volts 60mA display: 4.3x4.5x1.6 drive: 1.34kg (2.9lbs) display: flush/surface/bracket 8 backlit buttons 86mm segmented LCD 18mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46 ST4000 Plus MkII Wheel Pilot 12v systems 10 - 15 volts 60mA display: 4.3x4.5x1.6 drive: 1.43kg (3.2lbs) display: flush/surface/bracket 8 backlit buttons 86mm segmented LCD 18mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46 Sportpilot/Sportpilot Plus Wheel Pilots 12v systems 10 - 15 volts 60mA ST5000 Plus SailPilot Packaged Pilots 12v systems 10 - 15 volts 60mA

37 - 43

T400/400G Course Computers 12v, 24v systems 10 - 32 volts * 300mA 12.1x7.7x2.75 2.1kg (4.6lbs) surface (2) (2) (2) -10C to +55C -10C to +70C up to 80% drip resistant
(via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (2) (2) (2) -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (5 to 20/second) off course/XTE/watch SeaTalk/drivestop/no data/volts (on main display) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (5 to 20/second) off course/wind/XTE/depth/watch SeaTalk/drivestop/no data/volts (3 pages) (7 pages) (with 150G/400G) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option -10C to +70C -10C to +70C up to 95% CFR46
manual manual and Autolearn with 150G manual and Autolearn with 400G automatic/manual automatic/manual automatic/manual (9 levels) (9 levels) (9 levels) (9 levels) (up to 9 levels) (up to 9 levels) (5 to 20/second) (5 to 20/second) (5 to 20/second) off course/wind/XTE/depth/watch SeaTalk/drivestop/no data/volts (3 pages) (15 pages) (with 150G/400G) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option (150G) (400G) (150G with ST6001+ or ST7001+) (400G with ST6001+ or ST7001+) (150G) (400G) T150 T400 standard on 150G, option on T150 standard on 400G, option on T400 all type 1 12v drives and pumps all type 1, 2 and 3 drives and pumps standard in corepack standard in corepack standard in corepack standard in corepack
Modular inboard autopilot systems complete modular inboard autpilot systems consist of a control head, corepack and drive unit Control heads E12098 ST6001 Plus E12100 ST6001 Plus flush mount E12099 ST7001 Plus M81100 Raypilot 650 Remote control units A15002 SeaTalk remote control A12016 ST600R remote 1.7 in 2.0 in Core packs E12091 150G 12v high performance corepack 2.9 in E12092 400G 12/24v high performance corepack E12054 T150 12v corepack 7.7 in E12055 T400 12/24v corepack Corepacks include: course computer, rudder reference transducer, and fluxgate compass. High performance corepacks include: course computer with built-in rate gyro and AST technology, standard fluxgate compass, and rotary rudder reference transducer. Autopilot accessories 9.1 in E12101 GyroPlus2 - external rate gyro transducer ST600R REMOTE RAYPILOT 650 CONTROL UNIT CONTROL

4.9 in 4.75 in 14.2 in 1.1 in 18.4 in 1.7 in 18.0 in
1.28 in 4.33 in 3.6 in 4.3 in 1.4 in 12.0 in 10.9 in 2.75 in 4.5 in 7.67 in
ST4000 PLUS, ST5000 PLUS AND ST6001 PLUS CONTROL UNITS

4.3 in

1.6 in 3.6 in 4.5 in 3.25 in

24.6 in

6.7 in

ST4000 PLUS WHEELPILOT

ST1000 PLUS AND ST2000 PLUS TILLER PILOT

ST7001 PLUS CONTROL UNIT

3.6 in

4.5 in

T150, 150G, T400 AND 400G COURSE COMPUTER
Selecting the right autopilot drive unit.
Drive Units and Corepacks Drive Units
Identify the correct drive unit type* for your boat (refer to the table on page 36), then use the following information to identify the correct model.
* We recommend that a Raymarine approved dealer confirms your selection and carries out the installation and commissioning. Approved installations carry a FULL 2 YEAR WORLDWIDE WARRANTY. For more information contact your national distributor (see outside back cover for details) or consult www.raymarine.com
Type 1 and 2 Rotary Drive

Universal Sterndrive

Type 1 and 2 Linear Drive
Displacement (maximum): Type 1: 10,000kg (22,000lb) Type 2: 20,000kg (44,000lb) Peak Output Torque: Type 1: 20Nm (180lb.in), Type 2: 34Nm (300lb.in) Maximum Shaft Speed: 33rpm
Drive: Electromechanical for power-assisted sterndrive systems *Not all sterndrive systems are supported Maximum Thrust: 330lb (150kg) Hardover Time: 8.8secs Stroke: 8.3in (214mm)
Displacement (maximum): Type 1: 10,000kg (22,000lb) Type 2S: 15,000kg (33,000lb), Type 2L: 20,000kg (44,000lb) Peak Thrust: Type 1: 295kg (650lb), Type 2S/Type 2L: 480kg (1050lb) Stroke: Type 1/Type 2S: 300mm (12in), Type 2L: 400mm (16in) Hardover Time (no load): Type 1/Type 2S: 11secs, Type 2L: 14secs Rudder Torque (maximum): Type 1: 735Nm (6500lb.in), Type 2S: 1190Nm (10,500lb.in), Type 2L: 1660Nm (14,700lb.in)
Drive Unit Part Numbers: M81135 Type 1 (12V) M81136 Type 2 (12V) Type 2 (24V) M81137 Corepack Part Numbers: E12091 150G (12V) with Rate Gyro and AST E12092 400G (12/24V) with Rate Gyro and AST E12054 T150 (12V) no Rate Gyro or AST E12055 T400 (12/24V) no Rate Gyro or AST
Drive Unit Part Numbers E12026 Universal Sterndrive Corepack Part Numbers: E12091 150G (12V) with Rate Gyro and AST E12054 T150 (12V) no Rate Gyro or AST Packaged Pilot Systems: ST5000 Plus Sterndrive E12037 E12049 ST5000 Plus Sterndrive Flush Mount Version

50 & 52

RAY53 12v systems 11.6 - 15.6 volts 6 amps (25W)/2 amps (1W) Fist microphone bulkhead mount cradle 16/9 key and channel control under hinged cover Full function base station 5.7"W x 2.14" H x 5.77"D 0.87kg (1.9lbs) bracket or optional flush mount 4 backlit keys & 3 rotary knobs oversized segmented LCD constant (red LED) Optional
-20C to +50C up to 95% CFR46 CFR46 (Ch16/working/WX channel) -
-20C to +50C up to 95% CFR46 CFR46 (Ch16/working/WX channel)
25W/1W 43dB +10log Po <10% at 1kHz for 3kHz deviation (open/short circuit of antenna) 2.5W (<10% distortion in 4 ohms) 3W (<10% distortion in 4 ohms) 0.35uV at 12dB SINAD 65dB <-40dB
25W/1W 43dB +10log Po <10% at 1kHz for 3kHz deviation (open/short circuit of antenna) 2.5W (<10% distortion in 4 ohms) 3W (<10% distortion in 4 ohms) 0.35uV at 12dB SINAD 70dB <-40dB

Loudhailer with Intercom

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) amps Physical: Primary handset Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type Base transceiver unit Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Display size and type Display lighting Ancillary items (1) Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Ancillary items (2) Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Humidity Waterproofing (base unit, fist mike and horn) standard KEY FEATURES Audio output of hailer (watts) Audio output of intercom (watts) Audio output of external speaker (watts) Output impedance Fog alert/siren mode Hailer listen mode Hailer options SYSTEM OPTIONS Multi-station option External loud speaker Intercom option (2 way) Auxiliary mode (transmission of external audio) Built in alarm (intrusion, bilge or other) Remote microphone Ray430 12v systems 10.8 - 16 volts 5 amps at 30W Fist Microphone 9.18x4.75x4.87 0.13kg (0.3lbs) cradle/hand held push to transmit button Full function base station 7.7x4.3x5.3 1.9kg (4.3lbs) surface or bracket 10 backlit buttons and 3 rotary knobs 64mm segmented LCD variable lighting Hailer Horn 6.5 x 11 x8.5 1.8kg (4.1lb) surface or bracket Remote Speaker 4.4x3.8x2.2 0.34kg (0.75lbs) bracket push button -15C to +55C up to 95% CFR46 30W 4.5W 4.5W 8 ohms 9 types (auto/manual including air horn sound) fore, aft or both options (base unit and up to 4 remote intercom speakers) base unit/remote speaker/hailer horn (with remote intercom speakers) (auxiliary input via AUX 1 and 2) (external alarm interface)
8.06 in 9.18 in 4.87 in 7.67 in 6.49 in

Loudhailers M95997 Ray430 loudhailer with horn M95997A Ray430 loudhailer (without horn) M95435 hailer horn M95998 intercom speaker VHF Radios E43003 Ray215 DSC VHF E43008 Ray230 DSC VHF System E43007 Ray230 DSC VHF System with DTMF interface E43006 Ray 45 VHF E43001 Ray 53 DSC VHF Communication Accessories E46021 Ray230/215 2nd station kit (handset/cable/loudspeaker) E46015 3m external speaker extension cable Ray215, Ray230 E46018 5m handset extension cable Ray215, Ray230 E46017 10m handset extension cable Ray215, Ray230 E46006 external speaker (Ray215)

4.75 in

RAY430

3.14 in

RAY215

5.70 in 2.12 in

2.14"
5.75 in 6.77 in 7.05 in 2.2 in 1.1 in 8.93 in 2.2 in

5.39 in 7.65 in 4.33 in

RAY 53 AND RAY 45 DIMENSIONS

3.03 in

RAY230

Fishfinders

Pathfinder Plus Fishfinders
GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) watts Physical: Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Cursor (context sensitive) Color/mono Display size and type Display resolution Display lighting (contrast) Connections: NMEA input (0183) NMEA output (0183) SeaTalk hsb2 Cartography Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard KEY FEATURES Nominal output power (RMS) Frequency Gain Range scales Range control Zoom size A-Scope Bottom Lock White Line Background color Scroll speed Fish symbols Variable Range Marker (VRM) Alarms Man OverBoard (MOB) ADDITIONAL FEATURES AND DISPLAY OPTIONS Course Deviation Indicator (rolling road) Bearing Deviation Indicator Data Boxes Data page (depth/temperature graph) Fishfinder presentation Fishfinder with full function Raychart* Fishfinder with full function radar option** SL755RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x4.7 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 64 levels (adjustable) (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product SL760RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit) 8.8x8.07x4.7 3.7 kg (8.2 lbs) bracket or panel 11 defined, 4 soft keys trackpad color 7" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) blue/black/white/grey auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product SL1250 Plus 12v, 24v, 32v systems 10.7 - 44 volts 30W (fully backlit) 11.5x11.4x5.5 5.8kg (12.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 10" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT(+) option -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 26 scales (2 to 1700m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) blue/black/white/grey auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen SL1250RC Plus L755RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x4.7 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 64 levels (adjustable) (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product via hsb2/SeaTalk L760 Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit)

Limited Warranty

Raymarine warrants each new Light Marine Product to be of good materials and workmanship. Raymarine, or its approved agents, will repair or exchange under warranty any parts proven to be defective in material or workmanship under normal use, for a period of 2 years/24 months* from date of sale to end user, or 30 months from date of shipment from Raymarine whichever expires first, except as provided below. Raymarine warranty covers the parts and labor associated with any warranty repair as described above, provided that the unit is returned to Raymarine or one of its appointed agents.

w o r l d - w i d e

Installed Warranty
In addition to the Limited Warranty cover as described above, Raymarine will, except as provided below, cover travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometers) and travel time of 2 hours, to enable onboard warranty service to be carried out on products where proof of installation or commission by Raymarine certified installers, can be shown. The Installed Warranty provides for onboard repair or exchange, by Raymarine or its approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer or 30 months, from date of shipment of the equipment from Raymarine whichever expires first, except as provided below.
Obtaining warranty service
In the event of warranty service being required, contact Raymarine or the nearest Raymarine certified service agent a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i.e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. Subject to the Limitations below, the unit will be repaired/ replaced at no further cost to the user and promptly returned to the user. In cases where the equipment has been installed by a Raymarine certified installer, (boat builder, installer dealer etc.) i.e. Installed Warranty, the nearest local service agent should be contacted and onboard service requested, the warranty card, correctly completed and stamped by the installing agent, must be available as authorization for onboard service.

*Raymarine warrants each Raymarine VHF Radio for a period of 3 years/36 months.
Standard Raymarine warranty and radio warranty.
Trademarks and notices. catalog credits
Trademarks and registered trademarks Autohelm, HSB, Raymarine, RayTech, RayTech Navigator, Sail Pilot, SeaTalk and Sportpilot are registered trademarks of Raymarine Limited. Apelco is a registered trademark of Raymarine Holdings Limited. (Registered in all major marketing territories). AST, Autoadapt, Auto GST, Autoseastate, Autotrim, Bidata, Marine Intelligence, Maxiview, On Board, Raychart, Raynav, Raypilot, Raystar, ST40, ST60, Seaclutter, Smart Route, Tridata and Waypoint Navigation are trademarks of Raymarine Limited. C-MAP and C-MAP NT are registered trademarks of C-MAP SRL. Navionics is a registered trademark of Navionics Company, Italy. All other product names are trademarks or registered trademarks of their respective owners. Photography Raymarine would like to thank the following organizations for the supply of lifestyle photography: Azimut S.p.A; Bavaria Yachts GMBH; Beneteau; Boston Whaler; Cobalt Boats; Fairline Boats PLC, Farr Pilot House Yachts; Formula; Hydro Sports; Linnsen Yachts B.V.; Luhrs Marine Group; Najad; Oyster Marine Ltd.;SeaRay Boats; Viknes; Billy Black; Martin Cleveland Photography; Jeff Gorbeck; Haddows Photography; Patrick Roach; Dick Shelton; Leigh Smith and Malcolm White. Safety notice Raymarine products are intended to be used as aids to navigation. Their accuracy can be affected by many factors, including environmental conditions, equipment failure or defects, and incorrect handling or use. It is the users responsibility to exercise common prudence and navigational judgment. Raymarine products should not be relied upon as a substitute for such prudence and judgment. The technical and graphical information contained in this catalog, to the best of our knowledge, was correct as it went to press. However, the Raymarine policy of continuous improvement and updating may change product specifications without prior notice. Therefore, unavoidable differences between the product and this catalog may occur from time to time, for which liability cannot be accepted by Raymarine.
Copyright 2002 Designed by Raymarine Limited, Produced by CPA Limited, Printed in England