Distributed by
Any reference to Raytheon or RTN in this manual should be interpreted as Raymarine. The names Raytheon and RTN are owned by the Raytheon Company.

_- _,_. _ _

ST50 SPEED
Installation and Operation
Nautech Limited, Anchorage Park, Portsmouth Hampshire, PO3 5TD, England. Telephone (0705) 693611, Telex 86364 NAUTEC G

Contents

1. 2. 2.1 2.2 2.3 2.4 2.5 2.6 2.7 3. 3.1 3.2 3.3 4. Specifications Control Head Installation Siting Mounting Procedure Power Supply Connection to Adjacent Instruments Connection to Separated Instruments Ring Connection Connection to SeaTalk Compatible Autopilots Transducer installation Connection to Instrument Transducer Selection Transducer Installation Fault Finding : 6 8
5. Maintenance 5.1 Control Head 5.2 Through Hull Transducers 5.3 Cabling 6. 6.1 6.1.1 6.1.2 6.2 6.3 6.4 6.5 7. 7.1 7.2 Operation Set Up Measurement Units Display Contrast Adjustment Illumination Display Sequence - SPEED Display Sequence - TRIP Display Sequence - TIMER Log Calibration Manual Calibration Automatic Calibration 15

1. Specifications

The ST50 Speed can be used as a stand-alone instrument or when connected to the SeaTalk bus can supply information to a Multi Function Display, a Tridata Repeater or any SeaTalk compatible Autohelm Autopilot. Both the Multi Function Display and Tridata Repeater have an NMEA standard output providing speed information to other onboard electronic equipment. The timer functions operate independantly allowing boat speed and log information to be displayed whilst the timer is running. Note: It is not possible to use the ST50 Speed as a repeater unit without a transducer input. When a dedicated repeater is required use the ST50 Multi Function Display. Specifications 0 Power Supply - 11V to 16V DC at 50ma (illumination off).

l Operating Temperature

2. Control Head nstallation
1 lhtn (4.33111) t--------c

39mm (1.5in)

Note: Tlie back cover is designed to breath through a duct in the cable boss to prevent moisture accumulation.
- 0C to t70c. 0 Size 1lOmm (4.33in) x 1lOmm (4.33in) x 24mm (lin) Overall depth 39mm (1.5in). 0 Computer - 8 bit Intel Microprocessor t 8K Rom. 0 Display - Custom dot matrix/7 segment liquid crystal display (LCD). l Boat Speed - 0 to 60 knots (depending on transducer). 0 Average Speed - 0 to 60 knots. l Maximum Speed - 0 to 60 knots, user resettable. Resets on powerdown. Log - 0 to 9999.9nm, promenantly stored. 0 Trip Log - 0 to 999nm, user resettable. Resets on powerdown. 0 Sea Temperature Timer - 0 to 100 hours countup. - 10 minute countdown. - 5 minute countdown. 0 Illumination - 3 levels and OFF, user selectable. 0 Unit Selection - Speed in MPH or knots, user selectable. - Distance in NM or statute miles, user selectable. 0 Distance Lost Function - Indicates distance lost during a Tack in either feet or metres.

2.1 Siting

The ST50 speed instrument is designed for above or below deck installation. Position where it is: 0 Easy to read by the helmsman. 0 Reasonably well protected from physical damage. 0 At least 230mm (gin) from a compass. 0 At least 500mm (20in) from radio receiving equipment. 0 Accessable from behind to secure in place and run cables. 0 Normally viewed straight on for best display legability.
2.2 Mounting Procedure (Fig. 1) The mounting surface must be smooth and flat. 0 Use the template provided to mark the centres of the two fixing holes and central boss. Note: Adjacent units should have a 6mm (1/4in) separation to allow room for the protective covers. 0 Drill to 4mm (5132in) diameter. 0 Use a 50mm (2in) diameter cutter to drill the hole for the central boss 1. 0 Screw the two fixing studs 2, into the back cover. l Pass the cable tails through the central hole and secure the instrument with the thumb nuts provided 3. (A sealing gasket 4 is already attached to the back cover).
Bracket Mounting (Fig. 2) As an alternative to surface mounting, a bracket mounting kit (Cat. No. 9130) is available to allow the Instruments to be bracket mounted.
- -10C to 40C (14 to 104F).

.3 Power Supply (Fig. 3)

0 I ransducer -w 11
2.4 Connection to Adjacent lnstruments (Fig. 4)
Fig. 4 To Transduce1 To Transducer ,cz-1,
Fig. 5 SeaTalkExtensionCable Cat. No. 0131 (9m (3011) supplied)

2.6 Ring Connection

insrarrarrons with a iarge number ot tnstruments on the SeaTalk bus may require a second ring main connection to the Power Supply to avoid excessive voltage drops. This can be checked using the table below:-

Ra lalk Tails

SeaTalk Tails
All instruments receive both power and information from the SeaTalk bus. Each instrument has two SeaTalk connectors (3 pm) on short 15Omm @in) tails to allow adjacent units to simply plug together.
Power %&y c&e 2m (6ft) Red Screen s12v ov
The second connection should be made to the spare lead on the last instrument and led back to the circuit breaker.
2.7 Connection to SeaTalk Compatible Autopilots (Fig. 6)
If the vessels installation includes a SeaTalk Compatible Autopilot the ST50 instruments may be connected into the SeaTalk bus at any point. No separate connection to the 12V power supply is necessary as the instruments will receive power via the bus from the autopilot course computer.
2.5 Connection to Separated htruments (Fig. 5)
Separated instruments are connected using the SeaTalk Extension Cable (Cat. No. 0131). This is supplied with a SeaTalk connector fitted to each end and with a junction box to rejoin the cable if it is cut to ease routing or for shortening. If preferred, any 2 core screen cable which has the following specification may be used in the place of the SeaTalk cable.
Minimum Copper Area Screen 2 Cores 0.5mm* 0.5mm2 AWG Computer BUS Scre
Jest installations only require one connection to he 12V power supply. This is connected to the first SeaTalk nstrument using the 2 metre cable supplied. Plug the connector into the instrument and ead the other end back to the vessels listribution panel. Cut the cable to length, :onnect directly to the distribution panel and jrotect with a 5A circuit breaker. Connect the ed wire to t 12V and the screen to OV. The ,ellow wire should be cut back and insulated. Longer runs to the power supply can be made rsing the SeaTalk Extension Cable (Cat. No. 1131) which is 9m (3Oft) long.
To any f&her ST50 Instruments or Autopilot Control Units
3. Transducer Installation
3.1 Connection to instrument c+.l. PTCn C.^^A I.^l._^. , L^ ^ &^.^A.^^ LOL,,JIJJ))GG 111311IIIT;IIt11(13a Ucl113Llx
cable tail with connector. Each transducer is supplied with 14m (45ft) of cable and the connector fitted on the end simply plugs into the instrument cable tail (Fig. 7).
3.3 Transducer Installation I^ ^,I ^^^^^ ^^A ,L^ :-^l.rl:,.^^ ^.^^ I:-A.:L. ,,I ai, MSCJ tww L,IC 1113LI LLllIzi 3)Jpllt? Wllll
the transducer completely before proceeding with the installation. Installation of the through hull type is described below. Siting (Fig. 8)
Fig. 8 Sailing Yacht [D +

Installation (Fig. 9) 1 n,;,, d111111 \I,ll, tJllL IIlC 111 LL- --1--1-J - I 111 q 3.,.m/t ,o;.\.:La L-I- :- LIK >t!:It%,tt position and check both inside and out that the siting is good. l Use a 50mm (2in) diameter cutter to drill the hole from the outside. l Emery to remove burrs and roughen the surface to provide a good key. Clean inside and outside the hull removing any grease with a weak solvent cleaner or household detergent.

Semi Displacement

Planing
4 Hole Size c 50mm (2in) Dia.
SPEED (2095) and Transducer

q--->

3.2 Transducer Selection
The speed transducers are selected depending on the hull material:-
For accurate readings the transducer should be positioned within the shaded area indicated where it will be in clear flow. 0 Be ahead of propellors (10% W.L. length min.). l Be at least 150mm (6in) from the keel (in a sailing yacht ideally ahead of the keel). l Be near the centreline. l Be clear of other through hull fittings or projections. l Have sufficient clearance inside the hull to allow the nut to be fitted. l Have 1OOmm (4in) headroom above the through hull fitting to allow it to be withdrawn.
Remove the paddlewheel assembly and nut from the through hull fitting 2 and apply sealing compound 3 to the mating flange and up the thread 6mm (114in) greater than the hull thickness. Assemble the through hull fitting making sure that the arrow points forward. Do not overtighten the nut 1. Remove excess sealing compound. Insert blanking plug ready for launch. Check for leaks immediately the vessel is launched. Recheck within 8 to 24 hours.
Cabling 0 Route the cable back to the instrument. 0 Avoid running the cable close to flourescent lights, engine, radio transmitting equipment etc. as these may cause interference. 0 Keep the cable clear of the bilges and secure at regular intervals.

4. Fault Finding

All Autohelm products are subject to a
mmnmhc.nciwa N,~~,.tact nrwnr(~~m.I. y.nrinr tn narkino r.A.1 r.-.O

5. Maintenance

5.1 Control Head a ,,I L&l Lcllll LIIILIIIJ, rn.A^.r^+:^. _^., - In ,.%4,.;,. ,.^.A:,:^-r cNIlGl1XUII CIJ
appear on the window. This will not harm the instrument, and can be cleared by switching on the illumination to the brightest level. 0 Never use any chemical or abrasive materials to clean your ST50 Speed Instrument. If the instrument becomes dirty wipe clean with a damp cloth. 0 Periodically check the through-hull fitting for leaks. 0 Keep the O-rings of the Speed/Log transducer and plug well covered with Vaseline ensuring plug is always attached to transducer, ready for immediate use. 0 Always replace the Speed/Log transducer with the plug whenever the vessel is being hauled out or left for long periods. 0 Frequently check Speed/Log transducer for fouling or damage. 0 Clean the outside of the through hull fitting flange, or external transducer face with a stiff brush and protect with a single coat of antifouling. Clean the paddle-wheel and exposed end of Speed/Log transducer plug and apply single coat of anti-fouling.

and shipment. In the unlikely event that a fault does arise the following check list should help cure the problem.
Fault Instrument Display Blank Course No Supply Action Check Supply Check Cabling and security of SeaTalk Connectors Check Fuse/Breaker Return ST50 Speed for repair Check Cabling and security of Transducer Connector Clean Paddle Wheel Check security01 SeaTalk Connectors. Remove Instruments one by one to isolate faulty unit Check security of SeaTalk Connectors between functioning and nonfunctioning Instruments
5.3 Cabling I *,,AA r,,nn;n,Tr~L.,nr +l.^.,nl, Kl,.A.^^ - nlI,111111~~I~JI,II~11 lgG~r*,,cz,r;
5.2 Through Hull Transducers
possible and secure any coiled lengths at regular intervals. 0 Avoid running cables close to flourescent lights, engine, radio transmitting equipment etc. l Check cabling for chafing or damage to outer casing, replace where necessary and re-secure.
No Speed or Temperature Information No Speed Information No exchage of information between SeaTalk Instruments (i.e. illumination levels). Failure of a groupof the SeaTalk Chain Instruments in
Transducer Cabling Problem Transducer Paddle Wheel fouled SeaTalk Cabling Problem
Advice Should any difficulties arise, please consult Nautech Product Support Department in the U.K. or your own National Distributor who will be able to provide expert assistance.
SeaTalk Cabling/Connector problem

i. Operation

he ST50 Speed Instrument can be used as an rA;t.;A.ll mrA,.ln n r,.rn,-.r+,.,-4 +,-. n+L.*r 1IIclI IIIWIG I WllllGLlci LLIlcil lstruments to provide part of a fully integrated lstrumentation system which can be linked to ny of the Autohelm SeaTalk compatible utopilots.

6.1 Set Up

ihe Si30 Speeci is sei up ill iile iaciory io

Illumination

display speed in knots, distance in NM, and distance lost in feet. These can be changed to mph, statute miles and metres to suit your preference as follows:l Push and hold down for 2 seconds Speed and Trip together to select calibration mode.
0 Push Reset to change display units between feet and metres. l Push and hold down for 2 seconds Speed and Trip together toexit calibration mode and store the selected units.
Control of Illumination level is common to all ST50 Instrument Modules. The control is always selected using the left-hand push button. 0 Push and hold down the Speed button for 1 second to switch ON (if OFF), or to display current illumination level (if already on).

nulaheln

.-a.-. : 0 L. ! :. : ! :.
6.1.2 Display Contrast Adjustment
The LCD viewing angle can be user set to achieve optimum display legability.

Cd. TRIP -. r-1 --

Momentarily push Speed and Trip together. 0 Push Speed button within 8 seconds to select required illumination level. Lamp 3 High Lamp 2 Medium Lamp 1 Low LampOFF O f f The display will return to previous status after 8 seconds.
6.1.1 Measurement Units I.tr:lii-i-KII:ii;l
Push Reset to change display units between knotsand mph. - nt,P Ll

i.*.i i.;I i* *.!

Push Reset to increase and Timer to decrease the contrast level. 0 Adjust for optimum contrast. 0 Momentarily push Speed and Trip together to store the display setting. Note: Increasing the display setting will suit installations where the instrument is normally viewed from below.

1.: :.i. l?:

:.: ; :,
Push Reset to change display units between nautical miles and statute miles.

TRIP i 1

Decrease K;ast
6.3 Display Sequence: SPEED
Tack / i fIi i:-:: i.;:: I
6.5 Display Sequence: TIMER

( IPCCD n

Boat Speed
.!.*.,. ,. j.j.:.* j.: :. j. : ::j

::.- ,*. 1 *.

Trip Distance.: :.* : :,

-4 -I I.3

- Push Reset for 4 seconds to reset.
When in Tack mode the ST50 speed instrument gives a measure of lost distance during a tack based on the average speed over the last 30 seconds. Push Reset just before starting the tack to start the distance lost function.

-.-.__-

Timer.:. : :.; :.. :. i j : j j. c. i. i I. : : :.,.: i.,a 17 ,) 17 L!!,r,r r,( - Push Timer to start/stop. - Push Timer to freeze display (indicated by flashing colon).

Velocity Made Good 0 Log

.;.j* j.::l ::.*: :***; ?.

TRIP II

RtSlr I -1. :.; :. i i-3 :. is,:. I.i-.:-.------e;.: : *.-i *.--*. :- p*., ji y. I-.: 1 :. 1 j.j :, : : : j. :i.e.: *. * : :. :. i :.,: :. II

1. : *

1 !;I *: : a. 1

*.::*::-J

Race Timer _._, ~. :-, f ::I! p [.-I --.:-.-. ~~.?.?._L- _-.--
- only displayed if wind data available. l Average Boat Speed* ,____ -. ~~-~~~ _ ~~ :.:. ,. i-i j> j.: : -. j-j.*. L**.j : *, !. B- 87 a.3

I-._._ _~~.~_~ ~. ,

L ---1

Sea Temperature

a Tack the boat - The distance lost will now count up until the boat reaches its average speed on the previous tack. 0 Push Reset to reset the function ready for the next tack. Note: The tack function should be reset at least 30 seconds before tacking so that the average speed can be accurately calculated.
- Push Timer for 1 second to select 10 minute countdown. - Push Timer for 3 seconds to select 5 minute countdown. 0 Push Reset at anytime to reset.
- Push Reset to reset. - Average speed is calculated over a max. 24 hour period after reset and then flashes.
.:*. : :*.: :.*.I ] *., j j : j.**. j. j I ,-, ;-, I ! L., ,;,:.*.*

Maximum Speed.- ---

j *<. :. ::. :.: j ,-j.,.j :* *.* *: p. j: -.: ! :: :: : 7 -4. L I

,,I.Lt

Note: If timer is already running, use Timer to return to timer display.
- Push Reset to reset. *Display returns to current boat speed after 8 seconds.

,--. ___-_.

- ,. ,. _.

2. Log Calibration

As supplied all ST50 Instrument Modules are Tested and Calibrated to factory standards. It is Navigation purposes the following Log Calibration procedures are carried out for your specific installation. There are two methods of log calibration. 0 Manual Calibration - allows a calculated log calibration factor to be entered manually. 0 Automatic Calibration - allows up to four measured runs to be entered and compared against a known distance. The log calibration factor is automatically calculated.
imwwtnnt.that hafnrn r.a.I.-. WV._ 1tcino.D thic.,._. -.-. fnr --.- inctrlmxd.I.
7.1 Manual Calibration Procedure
Calculate Correction Factor(F). I/^^.. A:^*.,.F = ~wm~!~!ea~~ Measured distance Known distance - From a chart Measured distance - As recorded on speed instrument allowing for tidal flow as required.
7.2 Automatic Calibration Procedure
6 Seieci an easiiy ideniiiied marked measureci distance on a chart. 0 Carry out the calibration when tidal flow is least. 0 Complete a minimum of two runs (one in each direction) to cancel tide. Procedure Push and hold down for 2 seconds Speed and Trip together to select calibration mode, (______ ---. _~._

:-*. ; *.*.-a. ::i ii i.

At the start of the measured run push Speed Display shows run number and measured distance wrm I 1
Procedure l Push and hold down for 2 seconds Speed and Trip together to select calibration mode.
:a**.-. : : :: * *. r-l i.

SPIED I.I

L--.--- _-._---.I

WEID I I

Push Speed at the end of the run. - Display shows recorded distance for the run, and after 5 seconds the log calibration factor.
0 Push Speed to display log calibration factor.
Push Speed to select log calibration.
0 Calculate the new log Calibration Factor. = Displayed calibration factor x F (min. 0.25, max 1.50).
0 Push Speed to display distance. Repeat last two stages to run the measured distance in the opposite direction. 0 If required, repeat last two stages for up to 2 more calibration runs over the measured distance. 0 Push and hold down for 2 seconds Speed and Trip together to exit calibration and to store the new log calibration factor.
0 Adjust the displayed calibration factor using Reset to increase ( A ) or Timer to decrease ( T ). l Push and hold down for 2 seconds Speed and Trip together to exit calibration and to store new calibration factor.

L--.--

0 Adjust displayed distance using Reset to increase ( A ) and Timer to decrease (7 ), until it equals marked measured distance (minimum 0.25nm, maximum 2.50nm).
Note: If the calibration factor is not within 0.25 and 1.50 a mistake has been made in the calibration sequence and the previous calibration factor will be retained when exiting calibration mode. The trip distance will be lost whenever automatic calibration is used.

Pathfinder Plus Radar Displays
s p e c i f i c a t i o n s
GENERAL SL72 Plus Compact Radar Power: System (with 2D scanner) Nominal voltage (volts DC) 12v, 24v systems Absolute voltage range (volts DC) 10.7 - 32 volts Power consumption (typical) watts 38W (fully backlit including scanner) Power save option (timed transmit option) Physical: Overall dimensions (WxHxD) inches 8.8x8.07x2.9 Product weight kg (lbs) 1.2kg (2.6lbs) Mounting methods bracket or panel Control type(s) 11 defined, 4 soft keys Cursor (context sensitive) trackpad Color/mono mono Display size and type 7" FSTN LCD Display resolution 320x240 (1/4 VGA) Display lighting (contrast) 100 levels (adjustable) Connections: NMEA input (0183) (2) NMEA output (0183) via SeaTalk plug SeaTalk hsb2 Cartography 2x C-MAP NT(+) option Approvals: EMC (R and TTE and FCC) CE marked Environmental: Operating temperature range -10C to +50C Non operating temperature range -10C to +70C Humidity up to 95% Waterproofing standard CFR46 KEY FEATURES Range scales (dependant on scanner) 9 scales (1/8 to 24nm) Range rings (accuracy) on/off (+/-1.5% range) Bearing accuracy +/-1 Variable Range Marker (VRM) (2) Electronic Bearing Line (EBL) (2) Minimum range and discrimination 23 meters Head Up/North Up/Course Up True/Magnetic (variation source) (auto/manual) Relative or True Motion (requires heading input) Gain auto/manual Tune auto/manual Sea Clutter (plus harbor/offshore mode) auto/manual Rain Clutter manual Fast time constant (FTC) manual Interference rejection on/off Pulse length selection automatic Marks (100) Waypoint navigation (with plotter) Guard Zone (2) Zoom mode x2 (1/4 screen) Off centre function up to 66% of radius Wakes (short, medium, long, off) Target expansion Man OverBoard (MOB) MARPA FEATURES (REQUIRES HEADING INPUT) Target tracking Selectable target vectors Target risk assessment History plots Danger alarms Target data box ADDITIONAL FEATURES AND DISPLAY OPTIONS Active waypoint shown (lollipop) via NMEA or SeaTalk Radar/Chart synchronization (with Raychart) local Radar/Chart Overlay (with Raychart) Course Deviation Indicator (rolling road) Bearing Deviation Indicator Data Boxes split screen or 6 boxes Radar presentation full or half screen Radar with full function Raychart* SL72RC Plus Radar with full function fishfinder option** Scanner cable length 10m or 15m SL70 Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x2.9 1.2kg (2.6lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 100 levels (adjustable) (2) 2x C-MAP NT(+) option -10C to +50C -10C to +70C up to 95% CFRscales (1/8 to 72nm) on/off (+/-1.5% range) +/-1 (2) (2) 23 meters (auto/manual) auto/manual auto/manual auto/manual manual manual on/off automatic (100) (2) x2 (1/4 screen) up to 66% of radius (10 targets) via NMEA or SeaTalk local split screen or 6 boxes full or half screen SL70RC Plus SL70C Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit) 8.8x8.07x5.9 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 7" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT(+) option -10C to +50C -10C to +70C up to 95% CFRscales (1/8 to 72nm) on/off (+/-1.5% range) +/-1 (2) (2) 23 meters (auto/manual) auto/manual auto/manual auto/manual manual manual on/off automatic (100) (2) x2 (1/4 or full screen) up to 66% of radius (10 targets) via NMEA or SeaTalk local split screen or 6 boxes full or half screen SL70CRC Plus -

Product Range see pages

13&14
RL70 Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x2.9 1.2kg (2.6lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 100 levels (adjustable) (2) 2x C-MAP NT(+) option -10C to +50C -10C to +70C up to 95% CFRscales (1/8 to 72nm) on/off (+/-1.5% range) +/-1 (2) (2) 23 meters (auto/manual) auto/manual auto/manual auto/manual manual manual on/off automatic (100) (2) x2 (1/4 screen) up to 66% of radius (10 targets) via NMEA or SeaTalk local and via hsb2 split screen or 6 boxes full or half screen RL70RC Plus via hsb2 -

72nm 9410 +/-30 MHz 10 kW 8 (auto/target expand) 70 seconds <2.5 seconds 1.horizontal <-22dB 24rpm 60MHz 12/3/0.7/0.5MHz
Pathfinder SL72 systems Each SL72 Plus system consist of a SL72 Plus display and 2D antenna E52026 SL72 Plus system with 10m cable E52027 SL72 Plus system with 15m cable with built in Raychart E52041 SL72RC Plus system with 10m cable E52042 SL72RC Plus system with 15m cable Pathfinder displays Combine with any Pathfinder scanner to create a radar system. Pathfinder radar displays with hsb2 E52031 RL70 Plus 7" monochrome LCD E52033 RL70C Plus 7" color LCD E52037 RL80C Plus 10.4" color LCD E52039 R70 Plus 7" monochrome CRT E52035 R80 Plus 10" monochrome CRT with built in Raychart and hsb2 E52032 RL70RC Plus 7" monochrome LCD E52034 RL70CRC Plus 7" color LCD E52038 RL80CRC Plus 10.4" color LCD E52040 R70RC Plus 7" monochrome CRT E52036 R80RC Plus 10" monochrome CRT

4.15 in 8.76 in 2.95 in

9.56 in

10.8 in 16 in

8.1 in

8.5 in

8.9 in
16.8 in 51.4 in (48") 75.5 in (72")

11.65 in

48" AND 72" OPEN ARRAY SL72 PLUS, SL70 PLUS AND RL70 PLUS

8.76 in 6.04 in 8.9 in

R70 PLUS

5.95 in 18.4 in

7.3 in 23.6 in
18" AND 24" SL70C PLUS AND RL70C PLUS

5.47 in 11.26 in 3.82 in

Pathfinder Plus SL series radar displays E52043 SL70 Plus 7" monochrome LCD E52045 SL70C Plus 7" color LCD with built in Raychart E52044 SL70RC Plus 7" monochrome LCD E52046 SL70CRC Plus 7" color LCD Pathfinder radar scanners M92650 2D 2kW 18" radome with 15m cable M92652 4D 4kW 24" radome with 15m cable T52001 5S 4kW 48" open array with 15m cable T52013 7S 4kW 72" open array with 15m cable T52012 9S 10kW 48" open array with 15m cable (24v, 32v DC only) T52014 11S 10kW 72" open array with 15m cable (24v, 32v DC only)

12.3 in

Optional scanner cables M92728 15m pedestal cable E55017 15m Pathfinder open array radar arch cable (2 pc) M92705 25m pedestal cable M92699 Pathfinder extension cable (5m) M92700 Pathfinder extension cable (10m) E56001 Pathfinder 5m cable radome M92692 Pathfinder 10m cable for 2kW radome only M92668 Pathfinder 15m cable-radome M92669 Pathfinder 25m cable-radome Radar accessories E12102 Smart heading sensor Radar/hsb2 cables R55001 hsb2 cable (1m) R55002 hsb2 cable (3m) R55003 hsb2 cable (6m) R55004 hsb2 cable (10m) E55010 hsb2 cable (20m) E55040 hsb2 Y cable

Raychart 631 Plus 12v, 24v, 32v systems 10.7 - 44 volts 30W (fully backlit) 11.5x11.4x5.5 5.8kg (12.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 10" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT (+) -10C to +50C -10C to +70C up to 95% CFR46 1/64 to 4000nm 20 scales 150nm (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via hsb2/SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart)
1/64 to 4000nm 20 scales 150nm (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via hsb2/SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart)
Raystar 120 sold separately Raystar 120 sold separately Raystar 120 sold separately (auto/man tune) (auto/man tune) (auto/man tune) 3 levels for COG/SOG 3 levels for COG/SOG 3 levels for COG/SOG WGS-84 (or local) WGS-84 (or local) WGS-84 (or local) local and via hsb2 split screen or 6 boxes full or half screen 2 via hsb /SeaTalk via hsb2 local and via hsb2 split screen or 6 boxes full or half screen 2 via hsb /SeaTalk via hsb2 local and via hsb2 split screen or 6 boxes full or half screen 2 via hsb /SeaTalk via hsb2
*for the key features of the Raychart with radar option refer also to the Pathfinder Plus radar specification 'key features' (pages 60 and 61). **for the key features of the Raychart with fishfinder option refer also to the Pathfinder Plus fishfinder specification 'key features' (page 78). ***see Raystar 120 specification (page 65).
Raynav and Raychart Systems (Display with GPS)
GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) watts Physical: Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Cursor (context sensitive) Color/mono Display size and type Display resolution Display lighting (contrast) Connections: NMEA input (0183) NMEA output (0183) SeaTalk Cartography Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard KEY FEATURES Range scales Range options Max. detail of background map Head up/North Up/Course Up True/Magnetic (variation source) Waypoints Waypoint name Waypoint storage Waypoint entry Manual waypoint entry Waypoint transfer PC Waypoint transfer (via NMEA WPL sentence) Routes Route name Route storage Waypoints per route Tracks Points per track Track interval Smart Route (track to route) Alarms Timers Navigation information Navigation predictions GOTO/follow functions Tidal information supported Sunrise/Sunset predictions Man OverBoard (MOB) GPS FEATURES Type Signal acquisition Satellite Differential type Differential acquisition Beacon Differential Ready Position accuracy (RMS) Position accuracy with SD GPS (RMS) Speed accuracy (RMS) Filters Time to first fix from cold start (typical) Time to first fix (after initial cold start) Geodetic datum Position correction ADDITIONAL FEATURES and DISPLAY OPTIONS Course Deviation Indicator (rolling road) Bearing Deviation Indicator Ship's log Data Pages Raynav 300 12v, 24v systems 9 - 32 volts <6W (fully backlit and GPS) 7.7x4.3x3.9 0.75kg (1.65lbs) bracket or panel 8 defined, 4 soft keys trackpad mono 4.75" FSTN LCD 240xlevels (adjustable) -10C to +70C -10C to +70C up to 95% CFR46 1/64 to 1200nm 18 scales (auto/manual) (1000) 16 character database graphical/manual LatLon/BrgRng/TDs via SeaTalk/NMEA (20) 16 character database up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route passive antenna 12ch. parallel (C/A code) WAAS/EGNOS/MSAS automatic <15m <5m <0.3kts 3 levels for COG/SOG <2.5 min (<40 sec) typically <8 seconds WGS-84 (or local) 12 full screen pages Raychart 320 12v, 24v systems 9 - 32 volts <6W (fully backlit and GPS) 7.7x4.3x3.9 0.75kg (1.65lbs) bracket or panel 8 defined, 4 soft keys trackpad mono 4.75" FSTN LCD 240xlevels (adjustable) 2x C-MAP NT (+) -10C to +70C -10C to +70C up to 95% CFR46 1/64 to 1200nm 18 scales 3nm with overzoom (auto/manual) (1000) 16 character database/user cartridge graphical/manual LatLon/BrgRng/TDs via SeaTalk/NMEA (20) 16 character database/user cartridge up to 50 (5) 750 time/distance arrival/XTE/anchor/fix alarm clock/countdown position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (via chart) passive antenna 12ch. parallel (C/A code) WAAS/EGNOS/MSAS automatic <15m <5m <0.3kts 3 levels for COG/SOG <2.5 min (<40 sec) typically <8 seconds WGS-84 (or local) 12 full screen pages

19&20

Raychart 425 (with Raystar 120) 12v system 10 - 18 volts 9.6W (fully backlit and GPS) 7.2x6.6x2.9 0.75kg (1.65lbs) bracket or panel 6 defined keys trackpad mono 6" FSTN LCD 320x240 (1/4 VGA) 4 levels (adjustable) 1x Navionics NavChart -10C to +70C -10C to +70C up to 95% CFR46 1/8 to 4096nm 15 scales 256nm with overzoom (manual) (500) 8 character database graphical/manual LatLon via NMEA (20) 8 character database up to time/distance arrival/XTE/anchor/fix position/XTE/SOG/COG TTG/ETA waypoint/cursor/route (height and current) active antenna 12ch. parallel (C/A code) WAAS/EGNOS/MSAS automatic/manual (auto tune) <15m <5m <0.3kts <2.5min (<40 sec) typically <8 seconds WGS-84 (or local) 3 full screen pages

GPS Receivers

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) watts Physical: Overall dimensions (DxH) inches Product weight kg (lbs) Mounting methods Cable length Connections: NMEA input (0183) NMEA output (0183) SeaTalk Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard GPS FEATURES Type Signal acquisition Satellite Differential type Differential acquisition Beacon Differential Ready Position accuracy (RMS) Position accuracy with SD GPS (RMS) Speed accuracy (RMS) Time to first fix from cold start (typical) Time to first fix (after initial cold start) Geodetic datum Raystar 120 (NMEA or SeaTalk Version) 12v, 24v systems 9 - 30 volts (NMEA version) 9 - 18 volts (SeaTalk version) 1.5W diameter 3.7x1.2 0.13kg (0.29lbs) flush/pole/rail 10m (33') (NMEA version) (NMEA version) (SeaTalk version) -10C to +70C -10C to +70C up to 95% CFR46 active antenna 12ch. parallel (C/A code) WAAS/EGNOS/MSAS automatic (satellite) with RTCM input <15m <5m <0.3kts <2.5min (<40sec) typically <8 seconds WGS-84 (190 programmable alternatives)

1.2 in 7.67 in

3.07 in

3.15 in 4.33 in 4.8 in

Raycharts and SDGPS E32017 Raynav 300 SDGPS navigator E32015 Raychart 320 SDGPS chartplotter E32032 Raychart 425 Navionics chartplotter with Raystar 120 Pathfinder Plus SL Series Raycharts E32043 SL520 Plus 7" monochrome LCD packaged with Raystar 120 E32044 SL530 Plus 7" color LCD packaged with Raystar 120 E32045 SL631Plus 10.4" color LCD packaged with Raystar 120
RAYNAV 300 AND RAYCHART 320

8.76 in 6.04 in

RAYCHART 520 PLUS AND SL520 PLUS
Pathfinder Plus Series Raycharts with hsb2* E32034 Raychart 520 Plus 7" monochrome LCD E32035 Raychart 530C Plus 7" color LCD E32036 Raychart 631 Plus 10.4" color LCD *Raystar 120 SeaTalk sold separately SDGPS sensors E32025 Raystar 120 SeaTalk E32026 Raystar 120 NMEA

Sail Racer

Fishing Pro

Pathfinder PC

hsb2 kit

Use optional hsb kit Use optional hsb kit Use optional hsb2 kit Optional Interface box Optional Interface box Optional Interface box

ST290 Instruments

GENERAL Graphic Display Data Display Power: Nominal voltage (volts DC) 12v systems 12v systems Absolute voltage range (volts DC) 10 - 16 volts 10 - 16 volts Power consumption (typical) mA 75mA (illumination off) 75mA (illumination off) Physical: Overall dimensions (WxHxD) inches 6.7x4.9x1.8 6.7x4.9x1.8 Mounting methods flush/surface flush/surface Control type(s) 5 backlit buttons 5 backlit buttons Display size and type 140mm dot matrix LCD 140mm segmented LCD Maximum character size 48mm 25mm Display lighting 3 levels plus off 3 levels plus off Connections: NMEA input (0183) (via DPU) (via DPU) NMEA output (0183) (via DPU) (via DPU) SeaTalk (via DPU) (via DPU) SeaTalk2 (NMEA2000) in/out (2) (2) PC (RS232) and RayTech interface option (via E85001) Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range -10C to +70C -10C to +70C Non operating temperature range -10C to +70C -10C to +70C Humidity up to 95% up to 95% Waterproofing standard CFR46 CFR46 DISPLAY-CHAPTERS AND PAGES Speed Speed data current/max/average current/max/average Speed range (knots) 0 to 60kts 0 to 60kts Log range (nm) 0 to 99999nm 0 to 99999nm Log options total log and 5 trip logs total log and 5 trip logs Speed alarms high/low boat speed high/low boat speed Speed units knots/kph/mph knots/kph/mph Velocity Made Good (VMG) VMG to windward/WPT VMG to windward/WPT Depth Depth data current/min/max current/min/max Depth range (m) 0.8 to 180m (600') 0.8 to 180m (600') Depth offsets keel/waterline/transducer keel/waterline/transducer Depth alarms shallow/deep/anchor shallow/deep/anchor Depth units meter/fathom/feet meter/fathom/feet Depth trend arrows Wind Wind speed data apparent/true/max apparent/true/max Wind speed range (knots) Wind angle data relative apparent/true relative apparent/true Wind angle range 180 port and starboard 180 port and starboard Wind alarms high/low wind speed/angle high/low wind speed/angle Wind units knots/m/s/beaufort knots/m/s/beaufort Wind shift (head and lift) Docking wind relative to vessel plan Heading Heading data current/lock/average/next tack current/lock/average/next tack Heading offset and variation magnetic/true magnetic/true Heading alarms off course off course Locked compass heading option Navigation Latitude/Longitude Speed/Course Over Ground Course/Distance made good Waypoint data (WPT) Bearing/Distance to WPT Estimated Time of Arrival/Time To Go Cross Track Error (XTE) Course Deviation Indicator (rolling road) Route information GPS GPS status (Fix, No Fix, D-Fix) No. of satellites and HDOP Autopilot Autopilot control (with autopilot keypad) (with autopilot keypad) Autopilot status Gain and Response control Full pilot calibration Steer bar indicator Timers Local time and date (automatic via GPS) (automatic via GPS) Alarm clock Stop watch Race timer (3x count down/up) (3x count down/up) Engine data monitoring Information Water temperature (C/F) (C/F) Tide set/rate Sunrise/Sunset/Twilight time Position log Rudder angle indication Battery voltage Man OverBoard (MOB) repeater CUSTOM KEY FEATURES Various operating profiles Configurable favorites pages Graphs Transducer calibration Low power indication Adjustable display response time System option supplied with transducer (pod only) Instrument repeater standard product standard product SYSTEM OPTIONS Man OverBoard (MOB) keypad option Extra loud external alarm (via DPU) (via DPU) Compatible remote keypad options remote and remote plus remote and remote plus Compatible Autopilot keypad option Analogue Wind Display 12v systems 10 - 16 volts 65mA (illumination off) 4.9x4.9x1.5 flush/surface 4 backlit buttons 34mm segmented LCD 13mm 3 levels plus off (via DPU) (via DPU) (2) (via DPU) -10C to +70C -10C to +70C up to 95% CFR46 apparent/true/max 0 to 60kts apparent/true 180 port and starboard high/low wind speed knots/m/s/beaufort (LCD and pointer) standard product (via DPU) remote plus 12v systems 10 - 16 volts 65mA (illumination off) 4.9x4.9x1.5 flush/surface 4 backlit buttons 34mm segmented LCD 13mm 3 levels plus off (via DPU) (via DPU) (2) (via DPU) -10C to +70C -10C to +70C up to 95% CFR46 apparent/true/max 0 to 60kts apparent/true 20 to 55 port and starboard knots/m/s/beaufort (LCD and pointer) standard product remote plus 12v systems 10 - 16 volts 65mA (illumination off) 4.9x4.9x1.5 flush/surface 4 backlit buttons 34mm segmented LCD 13mm 3 levels plus off (via DPU) (via DPU) (2) (via DPU) -10C to +70C -10C to +70C up to 95% CFR46 current/locked/average magnetic/true COG via GPS (LCD and pointer) standard product (via DPU) remote plus -

MULTI Repeater 12v systems 10 - 16 volts 45mA 4.3x4.5x1.5 flush/surface/bracket 4 backlit buttons 92mm segmented LCD 36.4mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46
MAXIVIEW Repeater 12v systems 10 - 16 volts 45mA 7x4.3x2.3 surface/bracket 4 buttons 41.2mm 3 levels plus off option (2) -10C to +70C -10C to +70C up to 95% CFR46
current/min/max 0.8 to 180m (600') keel/waterline/transducer shallow/deep/anchor meter/fathom/feet apparent/true/max 0 to 60kts apparent/true 180 port and starboard high wind speed knots/m/s/beaufort current/locked/average magnetic/true off course manual manual manual/auto depth trend arrows autopilot status ST60 round flush mount opposite tack mode close haul (CH) option VMG available on CH magnified display on CH clubhouse (CL) option compass rose on CL (LCD and pointer) ST60 round flush mount COG via GPS (LCD and pointer) flush mount
current/max/average current/max/average current/max/average 0 to 60kts 0 to 60kts 0 to 60kts 0 to 99999nm 0 to 99999nm 0 to 99999nm 0 to 999.99nm 0 to 999.99nm 0 to 99999nm knots/kph/mph knots/kph/mph knots/mph -10C to +40C -10C to +40C -10C to +40C current/min/max current/min/max current/lost 0.8 to 180m (600') 0.8 to 180m (600') 0.8 to 180m (600') keel/waterline/transducer shallow/deep/anchor Repeater only Repeater only meter/fathom/feet meter/fathom/feet meter/feet apparent/true/max apparent/true/max 0 to 60kts 0 to 60kts apparent/true apparent/true 180 port and starboard 180 port and starboard repeater only repeater only knots/m/s/beaufort knots/m/s/beaufort current/locked/average current/locked/average magnetic/true magnetic/true repeater only repeater only repeater only repeater only stop/lap/countdown date/time/timers date/time/timers manual/via SOG vel. made good (VMG) program pages/chapters SOG via GPS vel. made good (VMG) 1/100knot resolution depth trend arrows depth trend arrows lat/lon SOG and COG CMG and DMG cross track error (XTE) XTE steer bar no. of satellites target waypoint (WPT) bearing/distance to WPT autopilot status flush mount battery volts and alarm repeater only flush mount program pages/chapters VMG thru water/to WPT lat/lon SOG and COG CMG and DMG cross track error (XTE) tide set and drift no. of satellites target waypoint (WPT) bearing/distance to WPT autopilot status repeater only flush mount

2.15 in

4.52 in

4.33 in

.47 in 4.33 in 1.33 in.86 in 7.0 in.94 in
5.04 in.84 in.68 in 3.7 in.67 in

ST60 DISPLAY HEAD

1.96 in 1.96 in 1.96 in

ST60 MAXIVIEW

1.96 in 3.18 in

ST40 INSTRUMENT HEAD

2.2 in 2.8 in

ST40 ROUND BIDATA

2.95 in

2.6 in

14.6 in
ST60 SPEED AND DEPTH TRANSDUCERS

15.5 in

ST40 SPEED AND DEPTH TRANSDUCERS

6.96 in 5.6 in

ST60 SHORT ARM WIND TRANSDUCER

ST60 instruments A22009 ST60 speed system A22001 ST60 speed display A22010 ST60 depth system A22002 ST60 depth display A22003 ST60 multi repeater A22011 ST60 wind rotavecta system A22012 ST60 wind vane system A22005 ST60 wind display A22006 ST60 close hauled wind display E22049 ST60 clubhouse wind display A22014 ST60 compass system A22007 ST60 compass display A22013 ST60 tridata system A22004 ST60 tridata display A25006 ST60 MaxiView handheld remote A22024 SeaTalk remote keypad A22036 ST60 MaxiView repeater A22015 ST60 rudder angle indicator system A22008 ST60 rudder angle display only ST60 round SeaTalk analogue repeaters A22029 analogue speed (sail) A22030 analogue speed (power) A22031 analogue depth (feet) A22032 analogue depth (meters) A22033 analogue wind A22034 analogue rudder angle indicator
ST60 transducers M78714 bronze depth, low profile through-hull M78716 bronze speed, self sealing speed through-hull E26011 bronze triducer through-hull E26019 bronze long stem depth through-hull E26020 bronze long stem triducer through-hull M78713 plastic depth, low profile through-hull M78712 plastic speed, self sealing speed through-hull M78717 retractable bronze depth through-hull M78718 retractable plastic depth through-hull E26001 in-hull plastic transducer E25018 standard masthead wind transducer E25019 long arm masthead wind transducer ST60 accessories E25009 mounting bracket A25003 flush mount kit
ST40 instruments E22043 ST40 speed system with throughhull transducer E22052 ST40 speed system with transom mount transducer E22044 ST40 depth system with throughhull transducer E22053 ST40 depth system with transom mount transducer E22045 ST40 bidata system with through-hull transducer E22054 ST40 bidata system with transom mount transducer E22047 ST40 wind system E22048 ST40 compass system E25024 ST40 desktop bracket E25020 ST40 grey bezel E25021 ST40 silver bezel E25022 ST40 carbon effect bezel E25023 ST40 iridescent bezel E22037 ST40 speed display E22038 ST40 depth display E22039 ST40 bidata display E22041 ST40 wind display E22042 ST40 compass display Z226 Bidata-R system Z235 Bidata-R display
ST40 transducers E26007 transom mount depth transducer E26008 through-hull depth transducer, plastic E26005 transom mount speed transducer E26009 through-hull speed transducer, plastic E26006 transom mount triducer SeaTalk cables D284 1m cable D288 20m cable D285 3m cable D286 5m cable D287 9m cable Dway junction box D188 ST50 female adapter cable D187 ST50 male adapter cable

Autopilots

Tiller, Wheel and Packaged Pilots

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (standby) mA Physical: Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Display size and type Maximum character size Display lighting Connections: NMEA input (0183) SeaTalk Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard KEY FEATURES Steer to compass Steer to wind Steer to navigation info (waypoint or route) Waypoint advance feature Autotack Selectable tack angle Autotrim, seastate Windtrim Autoadapt (for Northerly/Southerly environments) User calibration Compass deviation correction Gain Damping Response Adjustable turn rate Alarms Diagnostic alarms Rudder angle indication Direction to steer arrows ADDITIONAL FEATURES Predefined data displays Customisable data displays Repeat instrument and navigation data on pilot Man OverBoard (MOB) repeater DRIVE OPTIONS Standard drive Optional drives Thrust kg (lbs) with standard drive Thrust kg (lbs) with optional drive Stroke Maximum recommended boat displacement (std drive) Maximum recommended boat displacement (optional) SYSTEM OPTIONS Remote control option Multiple control displays Extra loud external alarm Autopilot status repeated on instruments External compass Rudder Reference option *Sterndrives designed to fit Volvo, Mercruiser etc. ST1000 Plus/ST2000 Plus Tiller Pilots 12v systems 10 - 15 volts 40mA 17.7x2.9x3.7 1.53kg (3.4lbs) reversible port or starboard 6 buttons 45mm segmented LCD 9mm 3 levels plus off -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (9 levels) (9 levels) (5 to 20/second) off course (3 pages) integral (drive/display/compass) ST1000+: 57kg (125lbs) ST2000+: 77kg (169lbs) 254mm (10") ST1000+: 3000kg (6600lbs) ST2000+: 4500kg (10000lbs) optional ST4000T/ST4000T GP Tiller Pilots 12v systems 10 - 15 volts 60mA display: 4.3x4.5x1.6 drive: 1.34kg (2.9lbs) display: flush/surface/bracket 8 backlit buttons 86mm segmented LCD 18mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46 ST4000 Plus MkII Wheel Pilot 12v systems 10 - 15 volts 60mA display: 4.3x4.5x1.6 drive: 1.43kg (3.2lbs) display: flush/surface/bracket 8 backlit buttons 86mm segmented LCD 18mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46 Sportpilot/Sportpilot Plus Wheel Pilots 12v systems 10 - 15 volts 60mA ST5000 Plus SailPilot Packaged Pilots 12v systems 10 - 15 volts 60mA

40 - 47

ST5000 Plus PowerPilot Packaged Pilots 12v systems 10 - 15 volts 60mA display: 4.3x4.5x1.6 drive: 3.25kg (7.2lbs) display: flush/surface/bracket 8 backlit buttons 86mm segmented LCD 18mm 3 levels plus off (2) -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (9 levels) (9 levels) (2 levels) (5 to 20/second) off course/wind/XTE/depth/watch SeaTalk/drivestop/no data/volts (3 pages) (7 pages) hydraulic pump sterndrive (Std or Universal)* sterndrive: 150kg (330lbs) sterndrive: 300mm (12") 9000kg (20000lbs) standard part

37 - 43

T400/400G Course Computers 12v, 24v systems 10 - 32 volts * 300mA 12.1x7.7x2.75 2.1kg (4.6lbs) surface (2) (2) (2) -10C to +55C -10C to +70C up to 80% drip resistant
(via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (via T150/T400 or 150G/400G) (2) (2) (2) -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (5 to 20/second) off course/XTE/watch SeaTalk/drivestop/no data/volts (on main display) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option -10C to +70C -10C to +70C up to 95% CFR46 manual automatic/manual (5 to 20/second) off course/wind/XTE/depth/watch SeaTalk/drivestop/no data/volts (3 pages) (7 pages) (with 150G/400G) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option -10C to +70C -10C to +70C up to 95% CFR46
manual manual and Autolearn with 150G manual and Autolearn with 400G automatic/manual automatic/manual automatic/manual (9 levels) (9 levels) (9 levels) (9 levels) (up to 9 levels) (up to 9 levels) (5 to 20/second) (5 to 20/second) (5 to 20/second) off course/wind/XTE/depth/watch SeaTalk/drivestop/no data/volts (3 pages) (15 pages) (with 150G/400G) (with 150G/400G) T150/T400 150G/400G any Raymarine drive option (150G) (400G) (150G with ST6001+ or ST7001+) (400G with ST6001+ or ST7001+) (150G) (400G) T150 T400 standard on 150G, option on T150 standard on 400G, option on T400 all type 1 12v drives and pumps all type 1, 2 and 3 drives and pumps standard in corepack standard in corepack standard in corepack standard in corepack
Modular inboard autopilot systems complete modular inboard autpilot systems consist of a control head, corepack and drive unit Control heads E12098 ST6001 Plus E12100 ST6001 Plus flush mount E12099 ST7001 Plus M81100 Raypilot 650 Remote control units A15002 SeaTalk remote control A12016 ST600R remote 1.7 in 2.0 in Core packs E12091 150G 12v high performance corepack 2.9 in E12092 400G 12/24v high performance corepack E12054 T150 12v corepack 7.7 in E12055 T400 12/24v corepack Corepacks include: course computer, rudder reference transducer, and fluxgate compass. High performance corepacks include: course computer with built-in rate gyro and AST technology, standard fluxgate compass, and rotary rudder reference transducer. Autopilot accessories 9.1 in E12101 GyroPlus2 - external rate gyro transducer ST600R REMOTE RAYPILOT 650 CONTROL UNIT CONTROL
4.9 in 4.75 in 14.2 in 1.1 in 18.4 in 1.7 in 18.0 in
1.28 in 4.33 in 3.6 in 4.3 in 1.4 in 12.0 in 10.9 in 2.75 in 4.5 in 7.67 in
ST4000 PLUS, ST5000 PLUS AND ST6001 PLUS CONTROL UNITS

4.3 in

1.6 in 3.6 in 4.5 in 3.25 in

24.6 in

6.7 in

ST4000 PLUS WHEELPILOT

ST1000 PLUS AND ST2000 PLUS TILLER PILOT

ST7001 PLUS CONTROL UNIT

3.6 in

4.5 in

T150, 150G, T400 AND 400G COURSE COMPUTER
Selecting the right autopilot drive unit.

7.8 in

10.8 in 7.2 in = =

10.0 in

4.0 in
30.6 in (T1/T2S) 36.6 in (T2L)

35.8 in

43.8 in

13.9 - 22.3 in

TYPE 1 AND 2 ROTARY DRIVE

UNIVERSAL STERNDRIVE

TYPE 1 AND 2 LINEAR DRIVE
10.0 in (T1/T2S) 14.0 in (T2l)
Selecting the right autopilot drive unit. Drive Units and Corepacks Corepack selection
Type 1 (12v) drives require T150 or 150G corepacks. Type 1 (24v), type 2 and type 3 (12 or 24v) drives require T400 or 400G corepacks.
Type 1, 2 and 3 Hydraulic Pump
Type 2 and 3 Hydraulic Linear Drive

Constant Running Pumps

Ram capacity: ST5000 Hydraulic 4.9in3 10.5in3 (80cc 172cc), Type 1: 4.9in3 14in3 (80cc 230cc), Type 2: 14in3 21in3 (230cc 350cc), Type 3: 21in3 30.5in3 (350cc 500cc) Maximum Stall Pressure at 12V: Type 1: 750psi (50bar), Type 2: 1450psi (100bar), Type 3: 1160psi (80bar) Peak Flow Rate (no load): Type 1: 67in3/min (1000cc/min), Type 2: 122in3/min (2000cc/min), Type 3: 175in3/min (2900cc/min)
Displacement (maximum): Type 2: 22,000kg (48,500lb), Type 3: 35,000kg (77,000lb) Peak Thrust: Type 2: 585kg (1290lb), Type 3: 1200kg (2700lb) Maximum Stroke: Type 2: 254mm (10in), Type 3: 300mm (12in) Hardover (no load): Type 2: 10secs, Type 3: 12secs Maximum Rudder Torque: Type 2: 1270Nm (11,300lb.in), Type 3: 3200Nm (28,800lb.in)
Ram capacity: CR1: 350cc 500cc (21in3 30in3) CR2: 500cc 1200cc (30in3 73in3) Maximum Stall Pressure: CR1: 50bar (750psi), CR2: 50bar (750psi) Peak Flow Rate (no load): CR1: 3000cc/min (180in3/min), CR2: 4500cc/min (270in3/min) Ram: single- or double-ended Voltage: 12V or 24V Drive Unit Part Numbers: M81125 CR1 (12V) M81127 CR1 (24V) M81126 CR2 (12V) M81128 CR2 (24V) Corepack Part Numbers: E12092 400G (12/24V) with Rate Gyro and AST E12055 T400 (12/24V) no Rate Gyro or AST
Drive Unit Part Numbers: M81120 Type 1 (12V) M81119 Type 1 (24V) M81121 Type 2 (12V) M81123 Type 2 (24V) M81122 Type 3 (12V) M81124 Type 3 (24V) Corepack Part Numbers: E12091 150G (12V) with Rate Gyro and AST E12092 400G (12/24V) with Rate Gyro and AST E12054 T150 (12V) no Rate Gyro or AST E12055 T400 (12/24V) no Rate Gyro or AST Packaged Pilot Systems: A12010 ST5000 Plus Hydraulic 20,000lb (9,000kg), T1 (12V) A12011 ST5000 Plus Outboard 20,000lb (9,000kg), T1 (12V) E12046 ST5000 Plus Hydraulic Flush Mount Version, T1 (12V) E12047 ST5000 Plus Outboard Flush Mount Version, T1 (12V)

50 & 52

RAY53 12v systems 11.6 - 15.6 volts 6 amps (25W)/2 amps (1W) Fist microphone bulkhead mount cradle 16/9 key and channel control under hinged cover Full function base station 5.7"W x 2.14" H x 5.77"D 0.87kg (1.9lbs) bracket or optional flush mount 4 backlit keys & 3 rotary knobs oversized segmented LCD constant (red LED) Optional
-20C to +50C up to 95% CFR46 CFR46 (Ch16/working/WX channel) -
-20C to +50C up to 95% CFR46 CFR46 (Ch16/working/WX channel)
25W/1W 43dB +10log Po <10% at 1kHz for 3kHz deviation (open/short circuit of antenna) 2.5W (<10% distortion in 4 ohms) 3W (<10% distortion in 4 ohms) 0.35uV at 12dB SINAD 65dB <-40dB
25W/1W 43dB +10log Po <10% at 1kHz for 3kHz deviation (open/short circuit of antenna) 2.5W (<10% distortion in 4 ohms) 3W (<10% distortion in 4 ohms) 0.35uV at 12dB SINAD 70dB <-40dB

Loudhailer with Intercom

GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) amps Physical: Primary handset Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type Base transceiver unit Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Display size and type Display lighting Ancillary items (1) Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Ancillary items (2) Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Humidity Waterproofing (base unit, fist mike and horn) standard KEY FEATURES Audio output of hailer (watts) Audio output of intercom (watts) Audio output of external speaker (watts) Output impedance Fog alert/siren mode Hailer listen mode Hailer options SYSTEM OPTIONS Multi-station option External loud speaker Intercom option (2 way) Auxiliary mode (transmission of external audio) Built in alarm (intrusion, bilge or other) Remote microphone Ray430 12v systems 10.8 - 16 volts 5 amps at 30W Fist Microphone 9.18x4.75x4.87 0.13kg (0.3lbs) cradle/hand held push to transmit button Full function base station 7.7x4.3x5.3 1.9kg (4.3lbs) surface or bracket 10 backlit buttons and 3 rotary knobs 64mm segmented LCD variable lighting Hailer Horn 6.5 x 11 x8.5 1.8kg (4.1lb) surface or bracket Remote Speaker 4.4x3.8x2.2 0.34kg (0.75lbs) bracket push button -15C to +55C up to 95% CFR46 30W 4.5W 4.5W 8 ohms 9 types (auto/manual including air horn sound) fore, aft or both options (base unit and up to 4 remote intercom speakers) base unit/remote speaker/hailer horn (with remote intercom speakers) (auxiliary input via AUX 1 and 2) (external alarm interface)

8.06 in 9.18 in 4.87 in 7.67 in 6.49 in
Loudhailers M95997 Ray430 loudhailer with horn M95997A Ray430 loudhailer (without horn) M95435 hailer horn M95998 intercom speaker VHF Radios E43003 Ray215 DSC VHF E43008 Ray230 DSC VHF System E43007 Ray230 DSC VHF System with DTMF interface E43006 Ray 45 VHF E43001 Ray 53 DSC VHF Communication Accessories E46021 Ray230/215 2nd station kit (handset/cable/loudspeaker) E46015 3m external speaker extension cable Ray215, Ray230 E46018 5m handset extension cable Ray215, Ray230 E46017 10m handset extension cable Ray215, Ray230 E46006 external speaker (Ray215)

4.75 in

RAY430

3.14 in

RAY215

5.70 in 2.12 in

2.14"
5.75 in 6.77 in 7.05 in 2.2 in 1.1 in 8.93 in 2.2 in

5.39 in 7.65 in 4.33 in

RAY 53 AND RAY 45 DIMENSIONS

3.03 in

RAY230

Fishfinders

Pathfinder Plus Fishfinders
GENERAL Power: Nominal voltage (volts DC) Absolute voltage range (volts DC) Power consumption (typical) watts Physical: Overall dimensions (WxHxD) inches Product weight kg (lbs) Mounting methods Control type(s) Cursor (context sensitive) Color/mono Display size and type Display resolution Display lighting (contrast) Connections: NMEA input (0183) NMEA output (0183) SeaTalk hsb2 Cartography Approvals: EMC (Europe and FCC) CE marked Environmental: Operating temperature range Non operating temperature range Humidity Waterproofing standard KEY FEATURES Nominal output power (RMS) Frequency Gain Range scales Range control Zoom size A-Scope Bottom Lock White Line Background color Scroll speed Fish symbols Variable Range Marker (VRM) Alarms Man OverBoard (MOB) ADDITIONAL FEATURES AND DISPLAY OPTIONS Course Deviation Indicator (rolling road) Bearing Deviation Indicator Data Boxes Data page (depth/temperature graph) Fishfinder presentation Fishfinder with full function Raychart* Fishfinder with full function radar option** SL755RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x4.7 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 64 levels (adjustable) (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product SL760RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit) 8.8x8.07x4.7 3.7 kg (8.2 lbs) bracket or panel 11 defined, 4 soft keys trackpad color 7" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) blue/black/white/grey auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product SL1250 Plus 12v, 24v, 32v systems 10.7 - 44 volts 30W (fully backlit) 11.5x11.4x5.5 5.8kg (12.7lbs) bracket or panel 11 defined, 4 soft keys trackpad color 10" TFT LCD 640x480 (VGA) 100 levels (2) 2x C-MAP NT(+) option -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 26 scales (2 to 1700m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) blue/black/white/grey auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen SL1250RC Plus L755RC Plus 12v, 24v, 32v systems 10.7 - 44 volts 10W (fully backlit) 8.8x8.07x4.7 3.5kg (7.7lbs) bracket or panel 11 defined, 4 soft keys trackpad mono 7" FSTN LCD 320x240 (1/4 VGA) 64 levels (adjustable) (2) 2x C-MAP NT and NT+ -10C to +50C -10C to +70C up to 95% CFRwatts dual 200kHz/50kHz auto/manual 22 scales (2 to 1000m) auto/manual with shift auto/manual x2, x4, x6 (3 modes) full/split (adjust range) auto/manual fish/shallow/deep up to 6 boxes split screen option full, half or split screen standard product via hsb2/SeaTalk L760 Plus 12v, 24v, 32v systems 10.7 - 44 volts 20W (fully backlit)

Limited Warranty

Raymarine warrants each new Light Marine Product to be of good materials and workmanship. Raymarine, or its approved agents, will repair or exchange under warranty any parts proven to be defective in material or workmanship under normal use, for a period of 2 years/24 months* from date of sale to end user, or 30 months from date of shipment from Raymarine whichever expires first, except as provided below. Raymarine warranty covers the parts and labor associated with any warranty repair as described above, provided that the unit is returned to Raymarine or one of its appointed agents.

w o r l d - w i d e

Installed Warranty
In addition to the Limited Warranty cover as described above, Raymarine will, except as provided below, cover travel costs (auto mileage and tolls) up to 100 round trip highway miles (160 kilometers) and travel time of 2 hours, to enable onboard warranty service to be carried out on products where proof of installation or commission by Raymarine certified installers, can be shown. The Installed Warranty provides for onboard repair or exchange, by Raymarine or its approved service agents, for a period of 2 years/24 months, from date of sale of the boat to the end user where the equipment has been installed by a Raymarine certified installer, or from commissioning of the installation by a Raymarine certified installer or 30 months, from date of shipment of the equipment from Raymarine whichever expires first, except as provided below.
Obtaining warranty service
In the event of warranty service being required, contact Raymarine or the nearest Raymarine certified service agent a full list of local service agents are available on the Internet or can be requested from the nearest Raymarine agent. A suitable proof of purchase, showing date, place of purchase, and serial number must be made available to Raymarine or authorized service agent at the time of request for Warranty service. In cases where a Raymarine certified installer has not installed the product; i.e. Limited Warranty, the affected unit must be returned to the local Raymarine approved service agent, with a copy of proof of purchase and/or completed warranty card. Subject to the Limitations below, the unit will be repaired/ replaced at no further cost to the user and promptly returned to the user. In cases where the equipment has been installed by a Raymarine certified installer, (boat builder, installer dealer etc.) i.e. Installed Warranty, the nearest local service agent should be contacted and onboard service requested, the warranty card, correctly completed and stamped by the installing agent, must be available as authorization for onboard service.