R E G I N

C H A L L E N G E R

B U I L D I N G

A U T O M A T I O N
Optigo - Compact, economic and versatile stand-alone controller
The Optigo line represents a range of compact, reliable and cost-efficient stand-alone controllers for control of temperature, CO2, pressure, humidity and domestic hot water. Optigo is extremely easy to install, set-up and control and is mainly intended for smaller applications.
The timer handles for example night set-back, start or stop of fans during weekdays or during a day.
Quick and simple installation
Optigo is suitable for DIN-rail or cabinet mounting. Since the terminals are detachable, all connections can be made before Optigo is installed.
Operated with just a knob
Optigo has a knob with an encoder which makes the menu system very easy to use. You can read and set values shown in the back-lit display. A value is approved by pressing the knob.

Display information

Outdoor compensation configured Temperature control Menu holds changable values Active 010V input signal Change over Configuration level Menu number AO1 Graphic output signal Control mode 1 only Bargraph AO1 output level Bargraph AO2 output level AO2 Graphic output signal Control mode 1 only
TURN: Move up/down in the menus CLICK: Enter new menus or accept new setting PRESS 10 SEC: Enter the configuration menus

Chapter 2

Page 81

Applications Optigo 5

1. Temperature control

Applications Optigo 10

1. Supply temperature control

2. Humidity control

2. Outdoor compensated supply temperature control

3. CO2 control

3. Cascade temperature control

4. Pressure control

4. Heating control
5. Outdoor compensated pressure control
5. Domestic hot water control

Page 82

Chapter 2
Optigo - The controller for simple applications
Optigo represents a range of pre-programmed, configurable controllers intended for DIN-mounting. They can be set to handle applications like temperature control, humidity control, CO2 control, pressure control or domestic hot water control. Optigo has a knob with an encoder which makes the menu system very easy to use. You can read and set values shown in the back-lit display. A value is approved by pressing the knob. Optigo is suitable for DIN-rail or cabinet mounting. The terminals are detachable, which makes it possible to prewire before installation.
Display with language independent symbols Easy to configure Numeric/graphic display withbackground illumination Pre-loaded with several application nodes Simple handling with puch-/ turn knob

Optigo OP5

Optigo OP10

Supply voltage: 24 V AC

Optigo OP10-230

Supply voltage: 230 V AC

Control alternatives:
Temperature control CO2 control Humidity control Pressure control Pressure control with outdoor compensation
Supply air control Supply air control with outdoor compensation Extract air/room control with cascade function Radiator control with outdoor compensation Domestic hot water control

Functions as in OP10.

Functions:
Settable P and I values Selectable output signals for heating and/ or cooling (temperature control) Adjustable setting ranges for different sensors Changeover function (temperature control)
Air handling Minimum limit for dampers Start and stop of fans Frost protection regulation with heat retention Input for overheating protection from a heater 3-point or 010 V DC control Selectable output signals for heating and/ or cooling with/without damper control Alarm Frost protection/Overheating/Sensor error/Fan Indication Run indication from fans Built-in week-scheduler Input for extended running

Radiator systems

Night set-back of the setpoint for radiator control Pump stop and pump exercise Outdoor compensated supply temperature control with settable additional compensation of the curve at 0C outdoor temperature
Domestic hot water systems
PID control Periodical overheating of domestic hot water Prevents growth of Legionella bacteria

Page 83

Technical data Supply voltage Power consumption Ambient temperature Storage temperature Ambient humidity Mounting Protection class Display Dimensions Clock Inputs Analogue inputs, AI Digital inputs, DI Universal input, UI Outputs Analogue outputs Digital outputs (OP10 and OP10-230 only) 0.10 V DC, short-circuit protected Triac 24 V AC, 0.5 A (3-point control or alarm output) and one change-over relay 230 V AC, 5 A (fan start) OP10 I/O 10 Type OP5 OP10 OP10-230 OP10-10 Notes PT1000 Potential free closure Either 0.10 V DC or digital 24 V AC +/- 15% or 230 V AC (OP10-230 only) 4 VA 0.50C -40.+50C Max 90% RH DIN-rail mounting, 7 modules IP20 Backlit LCD, numeric/graphic 123x123x60 (WxHxD), 7 modules Week based 24 hour clock (OP10 only)
Model Overview AI DI UI AO DO Total I/O Description Controller Controller Controller
OP5 Supply voltage 24 V AC 24 V AC 230 V AC
See also the front mounting kit (e.g. FMCO) for DIN-rail mounting of controllers, displays and other devices from the Regin product range.

Page 84