OWNERS MANUAL

Warm Steam Vaporizer

Model DH-750

NOTE: Robitussin is a registered trademark of Whitehall-Robins Healthcare Caution: Robitussin product for illustration purpose only. Not for use in product. Keep out of reach of children.

Medicine cup

Heating Assembly
NOTE: Robitussin trademarks are used under license from Whitehall-Robins Healthcare, manufactured for and distributed by Honeywell Inc., Southborough, MA. U.S.A.
I M P O R TA N T S A F E T Y I N S T R U C T I O N S
READ ALL INSTRUCTIONS BEFORE USING THIS VAPORIZER AND SAVE THESE IMPORTANT INSTRUCTIONS FOR EASY REFERENCE. When using any electrical appliance, basic safety precautions should be followed including: 1. Always place this vaporizer on a firm, flat and level surface, at least 4 feet (1.2 metres) away from any person. It may not work properly on an uneven surface. 2. RISK OF INJURY TO PERSONS - STEAM EMITTED CAN CAUSE BURNS. NEVER POINT THE STEAM OUTLET DIRECTLY TOWARD ANY PERSON. 3. Do not place the vaporizer near any heat sources such as stoves, radiators or heaters. 4. Before using the vaporizer, check the power cord for any signs of damage. If the cord is found to be damaged, DO NOT USE and return the vaporizer to Honeywell under the warranty agreement for repair. Never allow the power cord to be immersed in water or other liquid. 5. This product is equipped with a polarized AC-line plug (a plug having one blade wider than the other). This plug will fit into the power outlet only one way. This is a safety feature. NEVER connect the vaporizer to any power source other than a 120V AC polarized outlet. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug should still fail to fit, contact an electrician to replace the obsolete outlet. DO NOT defeat the safety purpose of the polarized plug. 6. Never plug in vaporizer without filling with water and always UNPLUG and empty the vaporizer before moving, filling, cleaning, or storing. UNPLUG the vaporizer before removing the electrode heating assembly. 7. RISK OF FIRE NEVER add salt to the water. This can cause excessive boiling and electrical overloading of your household electrical system. 8. DO NOT add vaporizer medicine or any medicine directly into the water. Place in the medicine cup and fill it halfway. Honeywell assumes no responsibility for consequences resulting from the use of medications in this vaporizer. 9. Do not OVER-FILL the vaporizer. Doing so may result in electrical shock.
10. This vaporizer requires regular cleaning. Refer to the CLEANING instructions provided. Never clean the vaporizer in any manner other than as instructed in this manual. 11. Unplug the vaporizer if the relative
humidity exceeds 60%. For proper humidity readings use a hygrometer which is available in many hardware and department stores, or by ordering one from Honeywell (see Care Products and Accessories).
12. DO NOT ADD ANY ROBITUSSIN DIRECTLY INTO THE UNIT OR WATER.
INSTRUCTIONS FOR USE AND CARE SET-UP
1. Select a firm, level, flat location at least six inches (15 cm) from any wall for proper air flow and convenient to an electrical outlet. Be sure that the steam outlet is pointed away from any persons. 2. Place the vaporizer on a water-resistant surface, as water can damage furniture and some flooring. Honeywell will not accept responsibility for property damage caused by water spillage. DO NOT over-fill the vaporizer as this may result in electrical shock. This unit can be filled in the vertical or horizontal position (Figure 3). Never add any chemicals or solutions to the water. Exclusive, Helping Handle : The Helping Handle makes the unit easy to carry when filled. Use this handle to return the filled unit back to the area of use (Figure 4). Place the unit down in a horizontal position prior to use (Figure 5). 3. Reposition the heating assembly onto the base. 4. Whenever refilling be sure to wipe out any residual water with a clean cloth or paper towel.

Fig.3 Fig.3

FILLING
We recommend that the vaporizer be disinfected prior to first use. Please see CLEANING instructions. 1. To remove the heating assembly from the base; insert the plug into the back of the heating assembly to release the safety lock (Figure 1). While holding the plug in this position, lift the power head off the unit base. 2. Fill the base with COOL tap water to the FILL LINE" located on the inside of the unit (Figure 2). DO NOT USE HOT WATER.

Fig. 1 Fig. 2

O P E R AT I O N
DO NOT OPERATE THE UNIT IN AN UPRIGHT VERTICAL POSITION (FIGURE 6).

Robitussin

CLEANING instructions. Refill using 1/2 tap water and 1/2 distilled water, which will dilute the mineral content of your water. 2. The vaporizer will automatically shut off when the water level drops below the heating electrodes. 3. When you are finished using the vaporizer unplug it and clean after each use.
Plug the filled vaporizer into a polarized 120V AC outlet. DO NOT FORCE THE POLARIZED PLUG INTO THE OUTLET; it will only fit one way. CAUTION: DO NOT PLUG IN THE VAPORIZER WITH WET HANDS AS ELECTRIC SHOCK COULD OCCUR. NOTE: If the vaporizer does not start producing steam within 25 minutes, it means that your waters mineral content is too low to allow for electrical current flow. Unplug and remove the Heating Assembly. Add a 1/4 teaspoon of baking soda per tank of water to initiate steaming action. Make sure to thoroughly mix the baking soda with the water in the base. Adding too much baking soda can cause excessive boiling and hot water spurting, which may cause burns. 1. If the vaporizer boils excessively, spurts hot water or blows fuses without having added any chemical additives, the water mineral content is TOO HIGH. Unplug the vaporizer and clean per the
4. ALWAYS be sure to discard any unused water in the base before storing or refilling.
USING THE MEDICINE CUP (OPTIONAL)
Place medicine in the medicine cup which is located on the top of the power head. HONEYWELL ASSUMES NO RESPONSIBILITY OR LIABILITY FOR CONSEQUENCES OR DAMAGES RESULTING FROM THE USE OF MEDICATIONS IN THIS VAPORIZER.

CLEANING

We recommend that you clean the vaporizer DAILY by wiping all surfaces dry using a paper towel or soft sponge. The vaporizer should also be cleaned WEEKLY according to the following instructions: Cleaning involves two steps: SCALE REMOVAL and DISINFECTING. Be sure to perform these in the proper order to avoid harmful chemical interactions. Do not use soap, detergents, or abrasive cleaners. 1. First, unplug the vaporizer.

2. To remove the heating assembly from the base: Insert the plug into the back of the heating assembly to release the safety lock (Figure 7). While holding the plug in this position, lift the heating assembly off the unit base. 3. Empty base and rinse with clean tap water.
(4 liters) water. Let solution stay in the base 20 minutes, swishing every few minutes to wet all surfaces. Gently scrub area around Heating Elements with a soft brush. Wet all surfaces.

TROUBLESHOOTING

There are no consumer serviceable parts inside the HEATING ASSEMBLY. If you experience any problem, please check the following potential problem areas before returning the vaporizer to Honeywell or to its original place of purchase. UNPLUG THE VAPORIZER BEFORE TROUBLESHOOTING.
S T E P O N E : W E E K LY S C A L E R E M O VA L (Base)
1. Fill the base with one 8-oz. (250 ml) cup of undiluted white vinegar. Let solution stay in the base for 20 minutes, swishing every few minutes to wet all surfaces. 2. With vinegar still in the base, clean all interior surfaces of the base with a soft brush or cloth to remove scale. Carefully wipe the exterior of the Heating Assembly and remove any scale buildup. 3. Flush the base thoroughly with clean, warm water to remove scale and cleaning solution before disinfecting base.
1. Be sure that the vaporizer has been filled to its proper level. 2. Empty base after 20 minutes. Rinse Base and Heating Assembly with water until bleach smell is gone. 3. Dry the inside with a clean cloth or paper towel. 4. Use a dry, soft cloth to wipe the outer surfaces.
END-OF-SEASON CARE AND STORAGE
1. Follow weekly CLEANING instructions at the end of humidification season or when the vaporizer will not be used for at least one week or more. 2. Let the vaporizer dry completely before storing. Do not store with water inside the base. BE SURE ALL COMPONENTS ARE DRY. Do not leave any water in the reservoir. Residual water may cause deposits that will impair future performance of this appliance.
STEP TWO: W E E K LY D I S I N F E C T I N G (Base and Heating Assembly)
1. Be sure the base is empty. Fill with 1 teaspoon chlorine bleach in 1 gallon
3. Store in a cool, dry location. 4. Remember to clean the vaporizer at the start of the next humidification season.
E L E C T R I C A L R AT I N G S
This product is rated 5 amps at 120V AC, 60Hz.

NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR VAPORIZER, PLEASE SEE THE WARRANTY FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN THE HOUSING OF THE HEATING ASSEMBLY YOURSELF. DOING SO WILL VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM STILL PERSISTS, PLEASE CALL:
Honeywell Inc. CONSUMER RELATIONS DEPARTMENT TOLL FREE: 1-800-332-1110
Mail questions or comments to:

Honeywell Inc.

Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772 U.S.A. Please be sure to specify model number.
CARE PRODUCTS AND ACCESSORIES
Item Hygrometer (measures room humidity level) Base Model DH -750 -1 Heating Assembly Model DH -750-2 DH-750-2 $ 8.00 $10.80 DH-750-1 $ 6.00 $ 8.10 Item No. HAC-555 Price (U.S.) Price (Can.) $19.99 $26.98
To order replacement parts or care products: 1. For credit card orders, please specify VISA, MASTERCARD or DISCOVER, with cardholder name and signature, card number and expiration date. Or, send a check or money order payable to Honeywell Inc. All orders should include a description of the item, item no., and quantity desired. Include your name, address, and a daytime telephone number, in case we need to get in touch with you. Please add $4.50 U.S./$ 6.10 Can. for shipping and handling. Massachusetts residents add 5% sales tax. Canadian residents please add 7% G.S.T. plus applicable provincial taxes. NOTE: Honeywell Inc. cannot ship to P.O. Box numbers.
Mail To: Honeywell Inc. Consumer Relations Dept. 250 Turnpike Road Southborough, MA 01772 U.S.A. 2. Or, call the Honeywell Consumer Relations Department on our toll-free number: 1-800-332-1110. VISA, MASTERCARD or DISCOVER are accepted. No CODs are accepted. Please allow four weeks for delivery.
L I M I T E D WA R R A N T Y
This product has been engineered and crafted with great care for your satisfaction. Please read all instructions before attempting to use this product. Be sure to fill out and return the enclosed card within 7 days of purchase. A. This 3 year limited warranty applies to repair or replacement of product found to be defective in material or workmanship. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. HONEYWELL IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to

the original purchaser of this product from the original date of purchase. B. At its option Honeywell will repair or replace this product if it is found defective in material or workmanship. Defective product should be returned directly to Honeywell. C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with this manual. D. Return defective product to the following address with a brief description of the problem. Include proof of purchase and a $5.00 U.S./$6.75 Can. check or money order for handling, return packing and shipping charges. Please include your name, address and a daytime phone number. You must prepay shipping charges. Mark carton Attention Returns Department. Ship to: Honeywell Inc. Returns Department Southpoint Distribution Center 4755 Southpoint Drive Memphis, TN 38118 U.S.A.
1999 All rights reserved. Honeywell Inc. and Whitehall-Robins Healthcare HU 4019.99

P/N 035-02338-000

OWNERS MANUAL
1.0 GALLON OUTPUT PER DAY* NATURAL COOL MOISTURE HUMIDIFIER Model DH-832 Series
*Output dependent on room temperature and humidity. Robitussin is a registered trademark of Whitehall-Robins Healthcare.
IMPORTANT SAFETY INSTRUCTIONS
READ AND SAVE THESE SAFETY INSTRUCTIONS BEFORE USING THIS HUMIDIFIER When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Always place this humidifier on a firm, flat and level surface. This humidifier may not work properly on an uneven surface. 2. 3. 4. Place this humidifier in an area where it is not accessible to children. Do not place the humidifier near any heat sources such as stoves, radiators, and heaters. Before using the humidifier, check the power cord for any signs of damage. If the cord is found to be damaged, DO NOT USE and return the humidifier to the manufacturer under the warranty agreement for repair. This appliance has a polarized plug (one blade is wider than the other). To reduce the risk of shock, this plug is intended to fit only one way in a polarized outlet. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. DO NOT attempt to defeat this safety feature. To disconnect the humidifier, first turn controls to the OFF position, then grip the plug and pull it from the wall outlet. Never pull by the cord. A loose fit between the AC outlet (receptacle) and plug may cause overheating and a distortion of the plug. Contact a qualified electrician to replace loose or worn outlet. The humidifier should always be unplugged and emptied when not in operation or while being serviced or cleaned. Never tilt or attempt to move the humidifier while it is operating or filled with water. UNPLUG the humidifier before moving.
10. This humidifier requires regular cleaning. Refer to the CLEANING instructions provided. Never clean the humidifier in any manner other than as instructed in this manual. 11. Turn the humidifier OFF if the relative humidity exceeds 60%, or if you notice moisture on the inside of your windows. For proper humidity reading use a hygrometer, which is available in many hardware and department stores, or by ordering one from manufacturer. (See CARE PRODUCTS.)

INTRODUCTION

Thank you for purchasing a Robitussin Natural Cool Moisture Humidifier.

HOW DOES IT WORK?

NATURAL COOL MOISTURE SYSTEM Dry air is pulled through the Natural Cool Moisture system and a quiet fan blows out invisible, moisture-balanced air. Unwanted minerals and bacteria from the water are trapped inside the Natural Cool Moisture filter. When the unit is running you will not see or feel a mist. You will know your humidifier is putting moisture into the air as you watch the water level in your tank decrease throughout the day.
W H AT I S H E A LT H S H I E L D A N T I M I C R O B I A L ?
Your Robitussin Natural Cool Moisture filter has been designed using new HealthShield* technology which prevents surface growth and migration of mold, fungus and bacteria in the filter for its life - approximately one season. Keep in mind, depending on your water quality, mineral deposits can still clog or discolor the filter, affect its life and that of the humidifier.

MODEL - DH-8 32:

Your humidifier is made up of these parts:
*HealthShield is registered with the Environmental Protection Agency (EPA).

SET UP

NOTE: We recommend that the humidifier be disinfected prior to first use. Please see CLEANING instructions. Select a firm, level, flat location - at least six inches (15 cm) from any wall for proper air flow (Fig. 1). Place the humidifier on a water-resistant surface, as water can damage furniture and some flooring. The manufacturer will not accept responsibility for property damage caused by water spillage.

FILLING

Remove the water tank by grasping handle and pulling straight up. Set aside (Fig. 1). Remove the Natural Cool Moisture filter from the base before filling the unit with water (Fig. 2). Soak filter in a sink full of cool water to help reduce mineral build up and place back in the humidifier while wet. DO NOT SQUEEZEORWRING OUT THE NATURAL COOLMOISTURE FILTER. To help extend the life of your filter repeat this step each time you fill your humidifier. Turn the Water Tank upside down so that the Fill Cap is facing up; unscrew the Fill Cap by turning it counter-clockwise and set aside. Fill the Water Tank with COOL tap water (Fig. 3). Distilled water is not necessary as the water is filtered by the Natural Cool Moisture filter. DO NOT USE HOT WATER. Doing so may damage the humidifier. Replace the fill cap by turning it clockwise. DO NOTOVER TIGHTEN. Turn the Water Tank rightside up. NOTE: WHEN CARRYING THE FILLED WATER TANK PLEASE USE THE HANDLE AND PLACE YOUR OTHER HAND UNDER THE TANK FOR ADDITIONAL SUPPORT.

Fig. 3 Fig. 1

Fig. 2

FILLING CONTINUED

Position the Water Tank in the humidifier and push into place. Some water will empty into the base. Once the filled tank has been positioned, do not attempt to move the humidifier. If it has to be moved, unplug the humidifier and remove the water tank first. CAUTION: DO NOT POUR WATER INTO THE GRILLE ON THE POWER BASE. DOING SO MAY DAMAGE THE HUMIDIFIER OR CAUSE PERSONAL INJURY.

OPERATION

CAUTION: DO NOT PLUG IN THE HUMIDIFIER WITH WET HANDS AS AN ELECTRICAL SHOCK COULD OCCUR. With the power switch in the OFF position, plug the filled humidifier into a polarized 120V outlet. DONOT FORCETHE POLARIZEDPLUG INTO THEOUTLET; it will only fit one way.

HUMIDITY CONTROL

Set the fan speed CONTROL to the desired position (Fig. 4). HIGH: For fast humidifying NORMAL: For quieter operation NOTE: The length of time your humidifier runs will vary depending on the quality of construction, room size, and insulation of your room and house, as well as the fan speed.

Fig. 4

Turn the humidifier OFFif the humidity level feels too moist or you notice condensation forming on the walls and/or windows. ALWAYSbesure to empty any unused water ni the Remove and Rinse Tray and/or Water Tank each time you refill the water tank or finish using the humidifier.

WEEKLY CLEANING

We recommend cleaning the humidifier once a week, more often if you have hard water, notice a build up of impurities or detect unpleasant odors. Cleaning involves two steps SCALE REMOVAL and DISINFECTING. Be sure to perform these in the proper order to avoid harmful chemical interactions. First, turn off and unplug the humidifier. Remove the Water Tank. Remove the Natural Cool Moisture filter from the Base. Empty any water from the Base. NOTE: REMOVE FILTER BEFORE CLEANING. Failure to remove filter during cleaning will destroy the filter. STEP ONE: STEP TWO:

SCALE REMOVAL

REMOVE AND RINSE TRAY 1. Fill the Remove and Rinse Tray with either: 1 cup (8 ozs.) of undiluted white vinegar or Use DuraRinse Humidifier Cleaner, part no. AC816, following the instructions on the bottle. 2. Let solution stand for 20 minutes. 3. With the vinegar or DuraRinse in the Remove and Rinse Tray clean all interior surfaces with a soft cloth or brush to help remove scale. 4. Rinse thoroughly with water to remove scale and cleaning solution.

DISINFECTING

WATER TANK/REMOVE AND RINSE TRAY 1. Fill the Water Tank with: 1 teaspoon of household bleach and 1 gallon of water Pour some of this solution into the Remove and Rinse Tray. 2. Let solution stand for 20 minutes. 3. Rinse with water until the odor of bleach is gone.

NOTE: THE USE OF OTHER WATER TREATMENT PRODUCTS AND CHEMICALS MAY CAUSE DETERIORATION OF THE FILTER OR DAMAGE THE HUMIDIFIER, THEREBY HINDERING THE HUMIDIFIERS EFFECTIVENESS.
PROLONGING THE LIFE OF THE FILTER AND MAINTAINING A CLEAN HUMIDIFIER
NOTE: DONOT ATTEMPT TO CLEAN THE NATURAL COOL MOISTURE FILTER WITH ANY CHEMICAL SOLUTIONS, DOING SO WILL DAMAGE THE FILTER. HealthShield prevents the surface growth and migration of mold, fungus, algae, and bacteria. It is normal for a filter to discolor from mineral build-up. This will vary depending on water quality. DONOT clean the filter using any chemical solution. If a Natural Cool Moisture filter appears to be clogged by hard water or mineral deposits, soak it in a sink full of cool water for 10 minutes. DO NOT SQUEEZE OR WRING OUT THE NATURAL COOLMOISTURE FILTER. Always place filter back in the humidifier wet. When positioning the Natural Cool Moisture filter in the humidifier, always make sure the diamond pattern is displayed lengthwise (see diagram below).
Close-Up of Filter Pad CORRECT INCORRECT
To prevent mineral deposits use DuraFree Humidifier Water Softener, part no. AC817, each time the Water Tank is refilled. Always purchase Honeywell brand Natural Cool Moisture filters as the fan motor of this humidifier and the Natural Cool Moisture filter are designed to function efficiently as a set. Using any other filter could damage the motor or reduce the humidifiers performance. Be sure to empty water from the Water Tank and Base when not in use.
END-OF-THE-SEASON CARE AND STORAGE
Follow weekly CLEANING instructions when the humidifier will not be used for at least one week or more, or at the end of the season. At the end of the season, remove and throw away the filter; do not store with a used filter. Dry the humidifier completely before storing. DO NOT store with water inside the Base, Water Tank, or Remove and Rinse Tray. Pack the unit in its original carton and store in a cool, dry location. Before next use, remember to install a new filter and clean the humidifier.

TROUBLE SHOOTING

Q: I hear the fan turning, but I dont see any mist. Is my humidifier operating properly? A: Dry air is pulled through the Natural Cool Moisture system and a fan disperses invisible, moisture balanced air. There is no mist emitted. When operating normally you will feel only cool air coming from the unit. Monitor the water level in your Tank/ Base. If you notice a decrease in the Water Tank over 24 hours then the unit is operating normally. Q: My unit has been running for several hours. I hear the fan spinning, but I do not notice the water level in the tank decreasing. A: First, check the Natural Cool Moisture filter to be sure it is wet. If the pad appears dry, remove it from the Base and gently rinse under cool water. Reposition wet filter in the Base. You may also want to note the current moisture level in your home. If the humidity level is over 60% the unit will not put out much moisture as your air is already saturated. Q: My filter has turned light brown and rust colored. Do I need a new filter? A: Probably not. Since your filter has been made with HealthShield technology the change in color indicates only a mineral deposit. Soak filter in a sink full of cool water to help break up deposits. The discoloration may remain but will not affect the humidifiers performance.

ELECTRICAL RATINGS

This product is rated 0.4 Amps at 120V, 60 Hz. NOTE: IF YOU EXPERIENCE A PROBLEM WITH YOUR HUMIDIFIERS POWER UNIT, PLEASE SEE THE WARRANTY FOR INSTRUCTIONS. PLEASE DO NOT ATTEMPT TO OPEN OR REPAIR THE HUMIDIFIER YOURSELF. DOING SO WILL VOID THE WARRANTY AND COULD CAUSE DAMAGE OR PERSONAL INJURY. IF THE PROBLEM PERSISTS, PLEASE CONTACT THE CONSUMER SERVICE CENTER.

CUSTOMER ASSISTANCE

Mail questions or comments to: Honeywell Consumer Service Center 250 Turnpike Road Southborough, MA 01772 e-mail: service@honeywell.com Please be sure to specify model number. Call us toll-free at: 1-800-332-1110 or visit our website at: www.honeywell.com/yourhome

CARE PRODUCTS

If your local dealer is out of stock, replacement parts and care products may be ordered directly from the manufacturer. You can call 1-800-332-1110 to order with a MasterCard, Visa or Discover or fill out the form below and mail it along with a check or money order (sorry no CODs accepted) to:
Honeywell Consumer Service Center 250 Turnpike Road Southborough, MA 01772 Please allow four to six weeks for delivery. Massachusetts residents please add 5% Sales Tax.
Natural Cool Moisture Filter, one per pack DuraFree Humidifier Water Softener (32 oz.) DuraRinse Humidifier Cleaner (32 oz.) Rinse-to-Clean Base Water Tank and Fill Cap Fill Cap Digital Hygrometer and Thermometer(F/C)
Measure room temperature and humidity level. Free standing can be used anywhere in the room.
Item No. AGW813 AC817 AC816 DH830-1 DH830-2 DH830-3 HAC555
US Price $ 9.99 5.00 5.00 10.00 19.99 5.00 19.99
SUBTOTAL MAResidents add 5% Sales Tax Shipping and Handling (US residents add $4.95) TOTAL ENCLOSED Name Address Check or Money Order Enclosed Credit Card No. Exp. Date Day Time Phone Signature

LIMITED WARRANTY

THREE YEAR LIMITED WARRANTY TERMS AND CONDITIONS You should first read all instructions before attempting to use this product. The enclosed Customer response card should be filled out and returned within 7 days of purchase.
A. This 3 year Limited Warranty applies to repair or replacement of product found to be defective in material or workmanship during the warranty period. This warranty does not apply to damage resulting from commercial, abusive, unreasonable use, or supplemental damage. Defects that are the result of normal wear and tear will not be considered manufacturing defects under this warranty. You should first read all instructions before attempting to use this product. THE MANUFACTURER IS NOT LIABLE FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES OF ANY NATURE. ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE ON THIS PRODUCT IS LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. Some jurisdictions do not allow the exclusion or limitation of incidental or consequential damages, or limitations on how long an implied warranty lasts, so the above limitations or exclusions may not apply to you. This warranty gives you specific legal rights, and you also may have other rights which vary from jurisdiction to jurisdiction. This warranty applies only to the original purchaser of this product from the original date of purchase. B. At its option, the manufacturer will repair or replace this product if it is found defective in material or workmanship within the warranty period. Defective product should be returned to the place of purchase in accordance with store policy. Thereafter, while within the warranty period, any defective product should be returned to the manufacturer. NOTE: THIS WARRANTY DOES NOT COVER THE NATURAL COOL MOISTURE FILTER, WHOSE PERFORMANCE WILL DEPEND UPON THE CONDITION OF THE WATER USED IN THE HUMIDIFIER. C. This warranty does not cover damage resulting from any unauthorized attempts to repair or from any use not in accordance with the instruction manual. D. Return defective product, freight paid, with proof of purchase and $10 U.S. check or money order for handling, return packing and shipping charges, to: Honeywell ATTN: Returns Department 4755 Southpoint Drive Memphis, TN 38118, U.S.A 1-800-332-1110