Factory Reset Procedures

Caution: Many of these procedures will erase all memory in the unit. Make sure you have backed up any data you wish to keep before performing these procedures! If a unit is not listed here, it does not have an initialization procedure that is user-executable.
Model A-30/33/37 A-50/80 A-70/90/90EX A-220 A-300PRO A-500PRO A-500S A-800PRO A-880 AD-8 AP-700 AT-Series AX-09 AX-1/7 AXIS-1 AX-Synth
Procedure Power on while holding WRITE. (Hold for 15 seconds) While holding the first, third, and fourth buttons under the display, press CHANNEL. Then press any cursor button Power on while holding down MANUAL, then press ENTER Power on while holding B and MEMORY Hold ACT and <, use the VALUE dial to select FACTORY RESET. Press ENTER twice. Hold ACT and <, use the VALUE dial to select FACTORY RESET. Press ENTER twice. Hold MIDI CH and PGM CHANGE, press the SYSTEM key, Use the VALUE dial to select SY6, press ENTER 3 times. Hold ACT and <, use the VALUE dial to select FACTORY RESET. Press ENTER twice. Power on while holding SIGNAL and MEMORY Power on while holding WRITE. Confirm that F flashes in the display, then release WRITE. Press WRITE again Power on, then press EXIT repeatedly to get ANALYZER/FILTER screen. Cursor to MENU, press ENTER. Cursor to SYSTEM, press ENTER. Cursor to INITIALIZE, press ENTER. Use VALUE to select ALL MEMORY, then press ENTER twice (Make sure disk drive is empty.) Power on while holding ONE TOUCH PROGRAM Power on while holding FAVORITE A, B, and WRITE. Press TONE 5, then press WRITE. Power on while holding WRITE. (Hold for 30 seconds) While holding FUNCTION, press the F#0, C#2, and D#2 keys Power on while holding INC/+, DEC/-, and TONE 7(ORGAN/CLAVI), then press WRITE. Procedure Press UTILITY. Cursor to Initialize. Press ENTER. Cursor to All. Press ENTER twice Power on while holding GUITAR, MIC, and LINE. Press ENTER. Press MENU. Cursor to Factory Reset. Press ENTER three times. Power on while holding INPUT SELECT/GUITAR/BASS, MIC, and LINE. Press ENTER Press UTILITY. Press CURSOR Right to select Initialize. Press ENTER. Press CURSOR Right to select All. Press ENTER twice Press UTILITY. Cursor to Initialize. Press ENTER. Cursor to All. Press ENTER twice Procedure Press MENU. Use the DATA dial to select INITIALIZE. Press ENTER twice. Press MENU. Use the < / > buttons to select Factory Reset. Press ENTER twice. Press UTILITY. Cursor right to INIT. Press ENTER/YES. Use CURSOR buttons to select desired target to be initilaized, (GLOBAL, FX, MIXER, ALL). Press ENTER/YES twice Power on while holding WRITE. Release WRITE then press WRITE again Power on while holding DEL and REPEAT, then press ENTER Procedure With the unit on, Hold WRITE and press SYSTEM. Press ENTER twice Power on while holding the START/STOP button until F shows in the display Power on while holding the MEMORY button until F shows in the display Power on while holding METRONOME MODE and LOOP MODE. Press WRITE Power on while holding MEMORY Power on while holding WRITE. Release, then press WRITE again
Model BR-8/532/1180 BR-600 BR-800 BR-864 BR-900CD/ 1200CD BR-1600CD Model CD-2 CD-2E/2i CDX-1 CE-20 CR-80
Model D-2 DB-30 DB-60 DB-88 DB-90 DD-20
2010 Roland Corporation U.S.

Page 1

DDR-30 DEP-3/5 DJ-70/70MKII DR-3 DR-5 DR-202 DR-550/550MKII DR-660 DR-670 DR-770 DR-880 DS-330
Power on while holding the #1 button Power on while holding MEMORY NO UP (^) and DOWN (v) Power on while holding the UP ARROW button to enter test mode. Press A, press C, press S1. When finished the screen will display IC21 = OK Press EDIT. CURSOR Right to select SYSTEM. Press ENTER. CURSOR Right to select <FACTORY RESET>. Press ENTER twice Power on while holding FRET LEFT (<) and RIGHT (>), then press ENTER twice Power on while holding MUTE and ROLL. Press TAP/ENTER. Cursor to YES in the display. Press TAP/ENTER Power on while holding -1 and +1, then press START Press UTILITY, then use LEFT (<) and RIGHT (>) to select [8] INIT. Press ENTER twice Power on while holding REC and STOP / CONT. Press ENTER twice Press UTILITY, then use LEFT (<) and RIGHT (>) to select [9] F. RST. Press ENTER twice Press EDIT. Press CURSOR Right to select Factory Reset. Press ENTER twice Power on while holding REVERB and SPLIT, then press YES Procedure Press FUNCTION so it is lit. Use the FAMILY </> buttons to select Utility, then use the SELECT </> buttons to select Factory Reset. Press TEMPO >/YES twice Power on while holding WRITE Power on while holding REC/PUNCH IN Power on while holding RECORDER Press MENU. Press UTILITY then press FACTORY RESET. Press EXECUTE. Power on while holding WRITE Power on while holding REC in the DISK RECORDER section Power on while holding WRITE Press UTILITY. Use the buttons under the display that correspond to <<PAGE>> to select FACTORY PRESET. Press EXECUTE, then press OK. When the screen displays RESET COMPLETE, turn the unit off, then on Press FUNCTION and use the PAGE (<) (>) buttons to select Factory Preset. Touch the Execute icon followed by the OK icon on the display screen. Power off then on Power on while holding WRITE Power on while holding USER PROGRAM/WRITE With the unit on, press FUNCTION until RESUME shows in the display. Then press TEMPO+ Power on while holding USER PROGRAM/WRITE Performance Sets need to be loaded from disk to restore factory default settings. Insert the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press PAGE ^ / v to select PRF MEM and press UPPER 1(Execute) While holding REC and PLAY, press STRINGS. Power off and then back on While holding REC and PLAY, press CHOIR. Power off and then back on Power on while holding REC Power on holding LIGHT and SELECT. Release, then press LIGHT and SELECT again Power on while holding USER PROGRAM/WRITE Power on while holding USER PROGRAM/WRITE Procedure Hold REVERB and press TRANSPOSE, hold OTHERS and use the +/- buttons to select Fct in the display. Press the Stop/Start button twice. With the unit on, press MENU. Press the UP or DOWN cursor buttons to select FACTORY RESET. Press 8 (EXECUTE) twice Press MENU. Use the CURSOR Up and Down buttons to select Factory Reset, then press F8 [Select] followed by F7 [OK]. Press F7 [OK] when completed.

Model E-09 E-10/20/30 E-35 E-36 E-50/60/80 E-56 E-66 E-68/70/86/96 E-300/500 E-600 EG-101 EM-10 EM-15/25 EM-20/30/50/55 EM-2000 ep-5/7/7MKII ep-9 ep-75/85 EQ-20 EXR-3/5 EXR-40/46OR
Model F-110 Fantom Fantom-G6/7/8

Page 2

Fantom-S/S88 Fantom-Xa Fantom-XR Fantom-X6/7/8 FC-100MKII FC-200 FG-10/1000 FP-2 FP-4 FP-5 FP-7 FP-8 FR-3 FR-5/7
Press MENU. Use the CURSOR Up or Down buttons to select Utility, then press ENTER. Press 3 (Factory Reset) Press 8 (Execute) Press EXIT. Press MENU. Turn the VALUE dial to select Utility and then press ENTER. Press F3. Press F6 Press MENU. Press CURSOR Down to select UTILITY. Press ENTER. Press CURSOR Down to select FACTORY RESET. Press ENTER twice Press MENU. Press the CURSOR DOWN button to select Utility. Press button 3 (Factory Reset). Press Button 8 (Exec). Cycle the power Power on while holding pedals #1, #2, and #8 Power on while holding the #10 pedal, then press the CTL pedal Power on while holding CLEAR and EXIT Power on while holding REVERB until Fct shows in the display Power on while holding FUNCTION Power on while holding PEDAL CONTROL Power on while holding FUNCTION Press FUNC and release. While holding PIANO, press FUNC again Power on while holding SET and ORCHESTRA. Power on while holding MENU/WRITE. Press the DATA/ENTER button Procedure Press MENU. Touch UTILITY, then touch FACTORY RESET. Touch EXECUTE Power on while holding WRITE Performance Sets need to be loaded from disk to restore factory default settings. Insert the factory ZIP Disk into the drive and power on. Press F5 (Disk), then F1 (Load). Press PAGE ^ / v to select PRF MEM and press UPPER 1 (Execute) Power on while holding PARAMETER + and -, then press VALUE + With the power off, set the GUITAR /BASS switch to match the instrument you are using. Power on while holding TUNER(STRING SEL). Press WRITE Poly Mode: Power on while holding PLAY, GENERAL EDIT, and IND EDIT. Mono Mode: Power on while holding TUNE, CONTROL ASSIGN, and DATA TRANSFER Power on while holding the #6, #7, and #8 buttons. Use the FUNCTION LEFT (<) and RIGHT (>) buttons to select 2.All Factory Preset, then press WRITE three times Power on while holding WRITE. Release WRITE, (The MEMORY indicator will flash), then press WRITE again Power on while pressing in the PARAMETER knob, then press WRITE Power on while holding Pedal #2, then press the VALUE + button. Now press EDIT/PLAY Power on while holding WRITE/COPY, then press YES Power on while holding WRITE, then press WRITE again Power on while holding Pedal #2, then press the PATCH+ button to select INI. Press EDIT/PLAY. Then press PATCH+ and PATCH- simultaneously Press SYSTEM. Press PARAMETER (>) right to select FACTORY RESET. Use VALUE to select ALL. Press WRITE twice Power on while holding the CHANNEL SELECT A and B buttons (within the PREAMP/SPEAKER section), then press WRITE Power on while holding MOD and SFX. Press WRITE Power on while holding MOD and FEEDBACKER/SLOW GEAR. Press WRITE Power on while holding the PREAMP ON/OFF and (PREAMP)TYPE/VARIATION buttons. Press WRITE Power on while holding COMP/LIMITER ON/OFF and TYPE VARIATION. Press WRITE Press SYSTEM. CURSOR right to select FACTORY RESET then press ENTER twice. Press FUNCTION. Press SELECT Left or Right to choose Utility. Press ENTER twice Press MENU. Use the CURSOR Up and Down buttons to select Utility then press ENTER. Use the CURSOR buttons to select Factory Reset then press ENTER twice. Power off and on. Press TUNER/UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) buttons to select FACT Page 3

Model G-70 G-600/800 G-1000 GI-10 GI-20 GM-70 GP-16 GP-20 GP-100 GR-09 GR-1 GR-20 GR-30 GR-33 GS-10 GT-3 GT-5 GT-6/8/Pro GT-6B GT-10/10B GW-7 GW-8 GX-700
Model HP-130 HP-557 HPD-10 HPD-15
INIT. Cursor to left and dial SYSTEM, then right and dial P#100. Press WRITE, then TUNER/UTILITY Procedure Power on while holding REC Press GUIDE button until it is NOT lit. Touch PIANO, then touch FUNCTION. Use Page (<) (>) to select the function page. Touch FACTORY RESET. Touch OK While holding SHIFT, press EDIT. Press the V button until you see FACTORY RESET. Press >, then use the +/- buttons to select ALL. Press V, then press 4/OK Press SYSTEM and use the PARAMETER (>) to select FACTORY RESET SYSTEM. Use the VALUE dial to select ALL and press WRITE Procedure Press DATA TRANSFER. Use PAGE UP (^) and DOWN (v) to select FACTORY PRESET. Press YES While holding EXIT, press UTILITY. Press F6 (EXECUTE), then F5 (YES) While holding SHIFT, press INIT/UTIL. Press INIT/UTIL repeatedly to select INITIALIZE WRITE. Use the DOWN/UP buttons to select FACTORY PRESET, then press WRITE Press EDIT. Press INIT/UTIL (Bank 7) repeatedly to select Factory Reset. Press REC then press WRITE Power on while holding RECORD located in the SEQUENCER section Press UTILITY. Use CURSOR buttons to select 16 SYSTEM FACTORY RESET. Press ENTER twice Press MENU. Press PAGE/CURSOR Right to select Factory Reset. Press ENTER twice Press MENU. Use ^/v to select UTILITY then press ENTER. ^/v to select FACTORY RESET then press ENTER twice. Press MENU. Use ^/v to select UTILITY then press ENTER. Press F3 FACTORY then press F6 EXECUTE. Press MENU. Use the VALUE Dial to select 5. Utility then press ENTER. Use the VALUE Dial to select Factory Reset then press ENTER. Press Button 5 [EXEC]. Press MENU. Use the CURSOR buttons to select UTILITY, then press ENTER. Use the CURSOR buttons to select FACTORY RESET, then press ENTER. Press 7 [EXEC] to confirm. Power off then back on when finished. Press CHORUS and REVERB (above INITIALIZE) simultaneously. Press VALUE UP (^) Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to select ALL. Press VALUE UP (^) Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER and then press WRITE Press UTILITY, then use the DATA dial to select FACTORY PRESET. Press ENTER twice Power on while holding NUMBER 8 (also labeled PERFORM 16 and CAPS). Press ENTER, then press WRITE Press VALUE to select Performance Mode. While holding VOLUME press VALUE. Use the CATEGORY/BANK dial to select Piano (LCD will display Fct). Press VALUE twice Press UTILITY. Cursor down once, then cursor right three times to select FACTORY PRESET. Press ENTER twice, then press UTILITY Press UTILITY. Press F6 twice to select MENU 3. Press F1. Then press F6. If necessary, use the VALUE DIAL to turn Memory Protect OFF and press F6 twice Press TUNE/FUNCTION. Press F5 (FACTORY), then F4 (JW RESET), then F3 (GS RESET), then F4 (YES) Power on while holding WRITE and FLUTE Press UTILITY. Use PAGE </> to select Factory Preset and press ENTER. Use PAGE </> to select ALL and press ENTER twice Procedure Press FUNCTION. Touch [System Setting]. Touch [Facotry Reset]. Touch [Execute Press the One Touch Program PIANO button. Touch FUNCTIONS. Touch FACTORY RESET

Model JD-800 JD-990 JP-8000 JP-8080 JS-30 JS-5 Juno-D Juno-Di Juno-G Juno-Gi Juno-Stage JV-30 JV-35/50 JV-80/90 JV-880 JV-1000 JV-1010 JV-1080 JV-2080 JW-50 JX-1 JX-305

Model KF-90 KR-5/7

Page 4
KR-15/15M KR-55 KR-75 KR-177 KR-277/375 KR-350 KR-377 KR-500 KR-570 KR-575 KR-577/977 KR-650 KR-770 KR-1070 KR-1077 KR-3000 KR-3500/4500 KR-4700/5000 KR-5500
Press the One Touch PIANO button. Touch FUNCTION SETTINGS. Touch FACTORY RESET. Touch EXECUTE. Touch YES Hold MIDI/FUNC and press CARD. Hold both VARIATION buttons for 5 seconds Press UTILITY and use the PAGE <</>> buttons to select Factory Preset. Press EXECUTE, then press OK In the Utility menu screen, press PAGE < (left) or PAGE >(right) to select the FACTORY PRESET page. Press EXECUTE. Press OK Press FUNCTION until it is lit. Use BEAT and TEMPO buttons to display FNC41. Press TRANSPOSE twice While holding LOAD and SAVE, press WRITE Press FUNCTION until it is lit. Use the PAGE left or PAGE right buttons at the bottom of the display until Factory Reset appears. Press FACTORY RESET next to the display. Press EXECUTE at the bottom of the display. Press OK While holding FROM and TO, press WRITE While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section) simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in the window. After loading is complete, power off and then back on Press FUNCTION and use the PAGE left or right buttons to select Factory Preset. Touch the Execute icon followed by the OK icon on the display screen. Power off then on Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK] While holding LOAD and SAVE, press WRITE While holding PART VOLUME ACCOMP, press TRACK 2 and 4 buttons (Composer section) simultaneously. Press PART VOLUME ACCOMP repeatedly to get FACTORY SETUP LOAD in the window. After loading is complete, power off and then back on Press UTILITY and use the PAGE <</>> buttons to select Factory Preset. Press EXECUTE, then press OK Press FUNCTION until it is lit. Touch [Factory Reset]. Touch [Execute]. Touch [OK] While holding FROM and TO, press WRITE While holding LOAD and SAVE, press WRITE While holding EDIT, press LOAD and SAVE While holding LOAD and SAVE, press WRITE Procedure Power on while holding ENTER Procedure Power on while holding FINALIZE and ROOM ACOUSTIC While holding EDIT, press WRITE. Use PARAMETER UP (^) and DOWN (v) to select ALL, then press WRITE. When completed, press EDIT to return to Play Mode Set the SELECT switch to the OPTICAL Input setting, then power on while holding the CLOCK SOURCE button Power on while holding F3 Power on while holding F3 Power on while holding F3 Press SETUP. Press INC or DEC until Fct shows in the display. Press ENTER, then press WRITE Power on while holding down SHIFT, then press ENTER With unit on, Press SYSTEM. Press F2 UTIL. Press CURSOR DOWN until Factory Reset appears. Press F1. Press F4 Power on while holding down SHIFT, then press ENTER. Note, this procedure takes several minutes Press SYSTEM, then hold SHIFT and press keyboard pad 16. CURSOR to Factory Rest and press ENTER twice. With the unit on, press MENU. Use CURSOR to select Utility. Press ENTER. Press F4 (Factory Reset.) Press F6 (Execute)

Model LVC-1N Model M-10/16DX M-660/760 M-1000 M-BD1/DC1 M-GS64/OC1 M-SE1/VS1 MC-09 MC-303 MC-307 MC-505 MC-808 MC-909

Page 5

ME-5 ME-6/6B ME-8/8B ME-10 ME-20/20B ME-25 ME-30 ME-33 ME-50/50B ME-70 ME-X MICRO BR MK-80 MKS-50 MMP-2 MT-32 MT-90S MT-100 MT-120/120S MT-200 MT-300S MV-8000/8800
Power on while holding pedals #1 and #2, then press WRITE immediately Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE Power on while holding PARAMETER LEFT (<) and DOWN (v), then press WRITE/COPY Power on while holding the BANK DOWN (v) pedal, then press WRITE In Manual Mode, hold EDIT/EXIT and press PEDAL 2. Press WRITE twice. Hold EXIT and press the MEMORY v (down) pedal. Press WRITE twice. Power on while holding PARAMETER RIGHT (>) and VALUE DOWN (-), then press WRITE/COPY Power on while holding the AMP/EFFECT right button and EZ TONE. Release, then press WRITE and wait for WRITE to stop flashing in the LCD. Power off, then on again Power on while holding WRITE and BANK Left <, then Press WRITE Twice Press Pedals 3 & 4 at the same time to switch to Manual Mode. Hold down EDIT / EXIT and press the MOD pedal. Press WRITE twice. Power on while holding PARAMETER DOWN (v) and LEFT (<), then press WRITE Power on while holding UTILITY. Press YES twice. While holding WRITE, press EDIT. While holding the LEFT (<) and RIGHT (>) cursor buttons, press UP (^) Poly Mode: Power on while holding NUMBER 4 and 8. Mono Mode: Power on while holding NUMBER 3 and 7 With the unit on press SYSTEM until it is orange. Press PAGE until INITIALIZE appears. Use the left VALUE control to select the desired target to be initialized. (SYSTEM, USER PATCHES, ALL). Press ENTER twice While holding MASTER VOLUME, press RHYTHM PART. Press PART 1 With the unit on, Press SONG and [4]. Press <(Bwd) or >(Fwd) until Factory Reset is displayed. Press (+). Press > (PLAY). Turn off the power, then on again While holding STOP, press DELETE. After the display flashes ALL CLEAR, press EXECUTE Power on while holding REPEAT, SONG (blue button), and PLAY. Press FWD repeatedly, until the window reads T-13. Press PLAY, then press REC. Power off, then on Power on while holding REPEAT, SONG (blue button), and PLAY. Use the DIAL to select T-15 in the window. Press PLAY, then press REC. Power off, then on Press MENU and use the VALUE DIAL to select 13:Factory Prset. Press ENTER/TRANSPOSE twice. Power off then on Press SYSTEM, press F5 (SysInfo), press F3 (Initialize), press F5 (Yes). Please note that all factory patches need to be reinstalled via CD-ROM. Procedure Power on while holding both INSTRUMENT buttons, then press PARAM 1 Power on while holding MIDI CH and NOTE NUMBER. Power off, then back on Power on while holding both VALUE (solid < and >) buttons Power on while holding COMMAND on the left edge of the keyboard Power on while holding the two buttons under the word STANDARD Press EDIT. Press the SYSTEM key, then press the # 8 key. SY8 will show in the display. Press ENTER three times Press EDIT. Press the SYSTEM key, then press the # 8 key. SY8 will show in the display. Press ENTER three times Press EDIT. Use the VALUE knob to select SYS, then press ENTER. Use the VALUE knob to select SY16, then press ENTER. Press ENTER twice. Power on while holding OCT/PARAM Power on while holding NUMBER buttons 1 and 2. (This reloads the first BANK of settings) Press UTILITY, then press the RIGHT (>) cursor button repeatedly to select INITIALIZE. Press ENTER, then [EXEC] Press MENU. Use the ^/v buttons to select Utility then press ENTER. Use the Cursor buttons to select Factory Reset then press ENTER. Power on while holding WRITE With the unit off, turn the TYPE knob to VO-WAH. Power on while holding

Model P-55 Pad-8 Pad-80 PC-150 PC-200/200MKII PCR-30/50/80 PCR-M30/50/80 PCR-300/500/800 PK-5 PM-16 PMA-5 Prelude Pro-E PW-10

Page 6

Model R-09/HR R-5/8/8MKII R-8M R-70 RA-50/90 RA-95 RA-800 RC-50 RD-150 RD-170 RD-300GX RD-300SX RD-500 RD-600 RD-700/GX/SX RM-2 RMP-3/5 RS-5/9 RS-50/70 RSP-550 RSS-10 RV-70
MANUAL/MEMORY. (ON/OFF will blink three times, then the MEMORY indicator blinks). Release MANUAL/MEMORY, then press MANUAL/MEMORY again Procedure Press MENU. Use the ^/v buttons to select FACTORY RESET. Press REC twice. Power on while holding CURSOR PAGE and PARAM SELECT, then press ENTER twice Power on while holding ENTER and the RIGHT (>) CURSOR button, then press ENTER twice Power on while holding MIDI and ASSIGN, then press YES twice Power on while holding WRITE Power on while holding REC (WARNING: This will erase the original factory Performance settings. However, you can save them to disk before doing this procedure.) Power on while holding WRITE Power on while holding PLAY MODE and LOOP SYNC. Press ENTER. Power on while holding REC and PLAY Power on while holding WRITE Press EDIT. Use INC/DEC to select Utility, then press ENTER. Use INC/DEC to select Factory Reset, then press ENTER twice. Press EDIT. Use INC/DEC to select UtL, then press ORGAN. Press ENTER twice. Power on while holding NUMBER 1 and 8. Press DEC/YES Press EDIT. Press the RIGHT PAGE button until Initialize All is displayed. Press INC/YES twice. Press EDIT to return to Play mode Press EDIT. CURSOR down to 9 UTILITY and press ENTER. CURSOR down to Factory Reset All and press ENTER three times Power on while holding VALUE UP, SELECT and METRONOME. When rSt flashes in the display, press METRONOME again Power on while holding STOP/START. Press and hold STOP/START until reset is completed. With the unit on, press UTILITY. Use VALUE + / - to select Factory Reset. Press ENTER. Use VALUE + / - to select All. Press ENTER twice Press PATCH so it is lit. Press UTILITY so it is lit. Use PAGE/CURSOR Left or Right to select Ag5: FACTORY RESET. Press ENTER twice Power on while holding PROGRAM/PAGE UP (^) and DOWN (v), then press WRITE Power on while holding LOCK and OPTION. (The MCR-8 LED lights.) Press DEMO PROGRAM four times. Press DEVICE ID Power on while holding WRITE and DOWN. Use the UP (^) and DOWN (v) buttons to select AL. Press WRITE. Power off, then back on Procedure Power on while holding CLEAR Power on while holding REVERB and SPLIT, then press YES Power on while holding both INSTRUMENT buttons, then press ALL While holding SELECT, press both INSTRUMENT buttons. Press ALL Power on while holding both INSTRUMENT buttons, then press ALL Press UTILITY. CURSOR UP and use the VALUE DIAL to select Factory Preset. CURSOR DOWN and use the VALUE DIAL to select ALL. Press ENTER twice Power on while holding CLEAR, then press REC Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Power on while holding PARAM UP (^) and VALUE UP (^). Press WRITE. Wait three seconds and press WRITE again Power on while holding in the NUMBER/VALUE knob. Press PARAMETER LEFT (<), then dial to STANDARD mode or GUITAR mode. Press WRITE Power on while holding PRESET PATCH and USER PATCH (keep holding until TAP TEMPO Page 7

Model SB-55 SC-33 SC-50/55/MKII SC-88 SC-155 SC-880 SD-35 SDE-330 SDX-330 SE-50 SE-70 SH-01
SH-32 SH-201 Sonic Cell SP-202 SP-303 SP-404 SP-505 SP-606 SP-808 SPD-S SPD-6 SPD-8 SPD-11/20 SPD-30 SRV-330 SRV-2000 SRV-3030/D SX-700
goes out). Press WRITE. Power on while holding 1/A. Press the VALUE UP/DOWN buttons to select the desired target to be initialized. Press WRITE/EXEC twice Power on while holding PRESET and USER. Press WRITE. Press MENU, then select UTILITY. Select FACTORY RESET, then select OK and press CURSOR/VALUE. CAUTION: This procedure will erase all of the internal samples and initialize the unit: Hold down CANCEL and press DEL, then press the A/B button. Press DEL Power on while holding CANCEL, REMAIN, DEL. Press REC Power on while holding CANCEL, REMAIN, and DEL. When ini shows in the display, press REC Press SONG or PTN to display the Play screen. Press SYSTEM to display the system screen. Press F1 (UTILITY). Press F3 (INIT). Set desired target to be initialized with VALUE dial.(ALL, SYSTEM, SAMPLE, SEQ). Press F1 twice Caution: Initializing the unit permanently deletes all samples out of the internal memory. Press MENU. Press CURSOR to select SYSTEM and then press ENTER. Press F3 twice Press SYSTEM/DISK and CURSOR to 4.Init SystemParam?. Press ENTER Press SETUP. Press PAGE Right to select INIT/DELETE. Press ENTER. Use + or to select ALL. Press ENTER Power on while holding DRUMS/U1, PERC/U2, SFX/U3 and OTHERS/U4. Press OTHERS/U4 to execute the reset Power on while holding EDIT, then press COPY. Use the VALUE UP (^) and DOWN (v) to select F A L in the window. Press ALL/ENTER Power on while holding ALL/ENTER and the DOWN ARROW button. Press ALL/ENTER Press MENU. Use Knob 1 to select SYSTEM then press Button 3 [ENTER]. Press Button 2 to select the F.RESET tab. Use Knob 1 to select Factory Reset then press Button 3 [ENTER]. Power on while holding SYSTEM and PROGRAM. Use the DATA dial to select SYSTEM + PROGRAM. Press MEMORY Factory: Power on while holding WRITE and REVERB NON-LINEAR. Delay Mode: Power on while holding WRITE, REVERB NON-LINEAR and ROOM SIMULATE With the unit on, press MEMORY. Use NUMBER/ENTER dial to select FACTORY RESET. Press NUMBER/ENTER twice Press UTILITY. Use PARAMETER LEFT (<) and RIGHT (>) to select FACT INIT. Press WRITE Procedure Power on while holding the + and buttons. Release them, and then press DRUM KIT Press MENU. Use the ^/v buttons to select 9 OPTIONS then press OK. Use the ^/v buttons to select Factory Reset then press OK. Use the Dial to select All then press the SEL [v] button. Press OK. Power on while holding EDIT and START/STOP, then press START/STOP again Power on while holding SHIFT and EDIT SETUP. Press INC/+ to select ALL. Press ENTER twice Press SYSTEM. Use the LEFT (<) and RIGHT (>) CURSOR buttons to select INI, then press ENTER. Cursor to HI HAT and use the DATA dial to select ALL. Press ENTER twice Power on while holding SYSTEM and JUMP, then press ENTER Press SETUP, then F3 MENU. Rotate VALUE to select RESET. Press F3 and use VALUE to select ALL. Press F3 EXEC to execute Press SETUP, then press F3 four times. Press SETUP, then press F4 four times Press SETUP, then press F5 three times Press SETUP. Press F5 twice Power on while holding TRIGGER SELECT and EDIT, release both then press EDIT again Power on while holding MODE and PATTERN GROUP KEY A Power on while holding MODE and TRACK #1 Power on while holding TRACK WRITE and TRACK #1 Page 8

Model TD-3 TD-4 TD-5 TD-6/V TD-7 TD-7T TD-8 TD-9 TD-10 TD-12 TD-20/20X TMC-6 TR-505 TR-626 TR-707/727

TR-909

Power on while holding TRACK #1 and PATTERN #1 Procedure Power on while holding PART and EDIT Procedure Press FUNCTION/MENU. Touch [Global Parameter]. Touch [ALL] Power on while holding MELODY/INTELL, CONTROLLERS and EFFECTS With the unit on, press the FUNCTION/MENU button. Press GLOBAL PARAMETER on the touch screen. Then press ALL on the touch screen Power on while holding PAGE left and PAGE right. Press WRITE Press [SYSTEM]. Press Page [>] to display Page 3. Press F2 [F.RST]. Select ALL , then press F6 [EXEC]. Press WRITE. With the unit on press UTILITY. Use NUMBER/VALUE dial to select Factory Reset. Press NUMBER/VALUE three times Power on while holding F1, F3, and F5. Press F6 for All, F4 for Patches, or F2 for System Power on while holding PAGE (>) and PAGE (<). Press WRITE twice Press SYSTEM. Press PAGE (>) to display page 3. Press F1 F.RST. Press F6 EXEC then press WRITE. Power on while holding WRITE. Release WRITE, then press WRITE again Power on while holding MAIN, SUB and PEDAL in the HARMONIC BAR PART section Power on while holding the UPPER, LOWER, and PEDAL buttons in the HARMONIC BAR PART section. Release and re- press the UPPER, LOWER, and PEDAL buttons once again With the unit on, confirm that the VOLUME is at the MIN position, then power off. Power on while holding BAND, WRITE, and H-BAR MANUAL Press EDIT. Use the RIGHT/LEFT ARROW buttons to select UTILITY and press ENTER. Use the UP/DOWN ARROW buttons to select Factory Reset. Press WRITE, then press ENTER Power one while holding BANK, WRITE, and H-BAR MANUAL. Continue holding BANK, WRITE, and H-BAR MANUAL until all panel indicators light. Press WRITE, then press F3 to access the INIT MENU screen. Press F4 to access the COLD BOOT screen, then press ENTER Press SYSTEM, then press F1-F4 ON/OFF. Use the VALUE dial to put a check in the ALL box and press ENTER three times Power on while holding PROJECT/SYS and F1. Continue to press F1 until completed Press FUNCTION so it is lit. Press F4 [UTILITY]. Use the VALUE dial to select 9. Initialize then press ENTER. Use the VALUE dial to select 2. Factory Reset All then press ENTER. Press F4 [Execute] then press F4 [OK]. Power on while holding BYPASS and FEMALE CHOIR. Power on while holding PLAY, VOICE EXPANSION, and MIDI Press MENU. Cursor to Factory Reset then press F2 [ENTER]. Press F1 [OK]. With the unit on, press UTILITY until it is lit. If the UTILITY Menu1 screen is displayed, press PART/ >. (the UTILITY Menu2 screen will appear). Press F1 (FACTORY). Press F6(EXEC) Press FUNCTION/ENTER. Use the +/- buttons to display Utl. Press STRINGS, then press FUNCTION/ENTER twice. With the unit on, Press MODE. Touch FACORY RESET, then touch EXECUTE Press UTILITY. Touch FACTORY RESET, then touch EXECUTE. Press MODE. Touch SYSTEM. Touch INIT. Touch EXECUTE. Hold shift and press F5/. Page to INIT. Press F1. Press ENTER/YES Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F1 (PrmIni). Press F5. Press ENTER/YES Hold SHIFT and press F4 (Utility). Press PAGE to get to page 3. Press F6 (PrmIni). Press F5. Press ENTER/YES Press UTILITY. Press PAGE to get to page 3. Press F6 (PrmIni). Press F5. Press Page 9

Model U-110

Model VA-3 VA-5/7 VA-76 V-BASS VB-99 VF-1 VG-8/8EX VG-88 VG-99 VGA-5/7 VK-7 VK-8 VK-8M VK-77 VK-88 VK-1000 VM-3100/Pro VM/C-7100/7200 V-Piano VP-7 VP-70 VP-770 VP-9000 VR-700 V-Synth V-Synth GT V-SynthXT VS-1880/1824CD VS-2000CD VS-2400CD VS-2480
ENTER/YES Power on while holding down the PRESET/USER button Procedure Press CONTROL and MASTER simultaneously. Use PARAMETER UP (^) and DOWN (v) to select ALL. Press VALUE UP (^) Procedure Press UTILITY. Use VALUE + and - to select INITIALIZE, then press ENTER. Use VALUE + and - to select FACTORY PRESET, then press ENTER Press UTIL/CARD and use the CURSOR buttons to select 4:FACTORY RESET. Press ENTER three times. If Write Protect is on, press DEC once, then press ENTER three times Press DISK/UTILITY, select SOUND, select PRESET, then press ENTER. Use the dial to turn Memory Protect OFF if necessary, then press ENTER twice Press UTILITY, press F6 (MENU) twice to select Factory, then ENTER. Press F6 (EXECUTE). Use the dial to turn Memory Protect OFF if necessary, press ENTER, then press F6 (EXECUTE) With the unit on, press UTILITY. Cursor down to Utility Menu 2. Cursor right 3 times to select FACTORY RESET. Press ENTER twice. If Internal Write Protect is set to ON, turn the VALUE dial to select OFF, then press ENTER 3 times While holding down VOLUME, press VALUE. Release them, then turn CATEGORY/BANK to select PIANO. Rotate VALUE until Fct shows in the display. Press VALUE Twice With unit on, press UTILITY. Press UP or DOWN cursor buttons to select the UTIL 2 page. Use LEFT or RIGHT cursor buttons to select FACTORY RESET. Press ENTER twice With the unit on, press UTILITY. Press CURSOR left until FACTORY RESET shows in the display. Press ENTER twice. If WRITE PROTECT ON is displayed, turn the VALUE dial to select OFF, then press ENTER twice With the unit on, press SYSTEM/UTILITY. Press F6 [MENU] to select menu 3. Press F1[FACTORY], then press F6 [FACTORY]. If INT WRITE PROTECT=ON is displayed, press DEC, then press F6 twice

March 31, 1999

SP-808

GROOVESAMPLER

Supplemental Notes

SP-808 CD-ROM Libraries from Time and Space/Zero-G Ltd.
The following is a list of compatable Time & Space CD-ROMs for the SP-808. These CD-ROMs require the use of the Roland SP-808 Wave File Converter software available for download at www.rolandus.com. You can contact Time and Space at 415-392-8933. TOTAL HOUSE (AUDIO/WAV FORMATS ONLY) A triple CD collection of the toughest house grooves, loops, basses, synths, vocals and effects. First in a brand new series of value-for-money collections. AMBIENT 2 (WAV ONLY) An impressive collection of analog and digital synths, from lush digital textures to vocoder loops and beyond. ANALOG TO DIGITAL VOLUMES 1 + 2 (WAV ONLY) Hundreds of sounds combined from the last 20 years worth of the world's greatest electronic instruments. Versatile for use in everything from trance to the hardest of hardcore techno. TECHNOTRANCE (WAV ONLY) A hard-hitting collection of techno synths, effects, effected drum voices and ethnic percussion (amongst others). A perennial best-seller. THE "CREATIVE ESSENTIALS" SERIES (ALL IN AUDIO/WAV/AIFF FORMATS) Each disc features between 200 & 400 inspiring sound-samples. All the sounds you will ever need to create up-todate music on your PC, Mac or Sampler. Vol 1 RHYTHM GUITAR AND FX A wide collection of riffs, licks, rhythms and effects in a variety of styles. Vol 2 PERCUSSION GROOVES An excellent collection of percussion grooves, using a wide range of instruments, including congas, cowbells, guiro, bongos, maracas and many more. Vol 3 BRASS ELEMENTS An exciting collection of sampled horn riffs, hits, stabs and effects. Vol 4 DANCE VOCALS Vocal ad-libs, hooks and phrases, both male and female. Vol 5 ELECTRIC DREAMZ Featuring powerful synthesized effects, hits and textures. Ideal for the industrialist or the more esoteric composer. Vol 6 TRANCE FORMATION A collection of mind-blowing synth sounds and textures. Featuring rhythmical, percussive patterns alongside strange colourful noises and sweeps. Vol 7 DREAM ZONE A remarkable collection of ethereal sounds, atmospheres and effects. Great for dreamy/eerie backdrops to any music production. 1999 Roland Corporation U.S. SP-808 CD-ROM Library Page 1 of 4
Creative Essentials series (continued)
SP-808 Supplemental Notes
Vol 8 SPICES OF INDIA A "hot dish" of Bhangra rhythms, instruments and vocals, hits and phrases, with the emphasis on rhythm and percussion. Vol 9 GUITAR SEPARATES A collection of highly usable guitar multi-samples, complete with a comprehensive collection of chords. Vol 10 GLOBAL S.F.X. Features an array of diverse natural sound effects - ranging from door bells to passing trains! Vol 11 HOUSE & GARAGE CONSTRUCTION Featuring a great variety of samples. Although it focusses on loops, it also features individual drum and percussion hits and various effects. Vol 12 HIP HOP & SWING BREAKDOWN This disc combines the best features of slo' jamz, R&B and hip hop from the Atlanta, Miami, New York & Oakland schools. Vol 13 JUNGLE FRENZY This top-value disc features drum rolls and fills, percussion loops and hits, basses, pads and jungle MC-ing, and the latest pads, noises and effects. Vol 14 LIVE BASS GROOVES A collection of electric bass guitar rhythms played in a variety of styles. Vol 15 WORLD CLASS BREAKS A disc packed with fresh grooves in the style of the 70's and 80's underground, covering, amongst others, techno, indie, house, jazz, swingbeat and many more. Vol 16 DRUM & PERCUSSION TOOLS A collection containing bass drums, snares, toms, hi-hats, cymbals and percussion samples. Vol 17 BASS SEPARATES This disc provides a superbly recorded set of multisampled real bass instruments for use in all areas of music production. Vol 18 ROCK AND POP VOCALS Another massive collecion of sampled vocal phrases performed by five different singers. (male/female) Vol 19 DANCE DRUMS A collection of individual drum sounds rather than loops - Program your own rhythms for an effective dance music production. Vol 20 UPFRONT LEAD GUITAR A collection for when you need a prominent riff or effect to stand out in the mix. Styles range frome grunge to blues and even ethnic. Vol 21 ETHNIC FLAVOURS A collection of samples recorded using excellent exponents of the rhythmic art from all corners of the globe Including tabla, Indian flute, talking drums, bells, choirs, pan pipes, oriental percussion and vocals. Vol 22 REGGAE CONNECTION A construction kit of sounds for reggae music production. Includes programmed and live rhythm loops and bass sounds, brass riffs, guitar licks and multisamples, organ riffs and more. 1999 Roland Corporation U.S. SP-808 CD-ROM Library Page 2 of 4

Vol 23 TECHNO PRISONERS A collection featuring all the sounds necessary to produce techno and hardcore dance music - drum loops, kicks, snares, industrial percussion, heavy machinery grooves and much more! Vol 24 FUNK CONSTRUCTION A disc featuring classy funky beats from the 70's including Rhodes,pianos and clavinets, organs, funky monosynth leads and more. Also features sax, drum fills and horn riffs. Vol 25 SYNTH BASS LOOPS This powerful collection consists of synth-generated loops ranging from 76 to 150 bpm, created using some of the latest equipment. Vol 26 VINTAGE KEYBOARDS A collection of classic keyboard sounds including Steinway grand pianos, Hammond, Mellotron & Vox organs. Vol 27 VOICES OF AFRICA Recommended to anyone seeking exotic sounds, rhythms and predominantly vocals. Complete with a multisamples set of sustained notes along with a selection of female yodels & male rhythmic chanting, clapping & long sung phrases. Vol 28 STRING TEXTURES A beautiful collection of string sections of varying sizes, with a variety of playing techniques. Vol 29 WOODWIND & BRASS A disc full of multisamples of flute, clarinet, bassoon, woodwind section, cornet, flugel & piccolo trumpet, plus French horn, trombone and trumpet, each solo and as a section. Vol 30 ORCHESTRAL FLAVOURS A superb collection of orchestral tuttis, sections, hits, sustains and phrases. One of the most comprehensive sets of orchestral sounds available.at an unbeatable price! Vol 31 JUNGLE FRENZY 2 More new breaks, transformations and cuts, basses, pads, effects and vocals. From the team that brought you the best-selling "Jungle Frenzy"! Vol 32 CUCKOOLAND AMBIENCE A disc full of moving and emotive atmospheres, pads and drones. MIXMAN SOUNDISCS (AUDIO/.TRK/WAV FORMATS ONLY) The official sound resource for Mixman Studio users. While still all discs provide samples in Mixman TRK format, all discs contain both Audio and WAV versions of all the sounds, to be used with any PC software or any hardware sampler. GLOSS Influences on this disc range from Chicago's deep gospel house sound to Detroit's moody techno rhythms. SKINNY PUPPY Distorted and dark are the themes from this ensemble of auditory assault - Eerie ambience, wicked basslines, schreeching guitars, insane percussive loops and crazy keys are the main ingredients in this collection. GEORGE CLINTON Funk all the way - containing horns, drums, bass, keys, synths and guitars.

1999 Roland Corporation U.S.

SP-808 CD-ROM Library

Page 3 of 4
K-KLASS A collection of aural textures from the European techno-house masters. Fusing house rhythms, techno sounds and tribal vibes in an irresistible package. STREET LEVEL West coast disco meets with East coast hard knock loops! Lots of funky basslines and vocals smooth out this mix of mid-tempo hip-hop sounds. HARDCORE (DJ BRISK & DJ DOUGAL) A collection of acid lines, arpeggios, lead synths, 303 sequences, kicks and claps. A hyper-happy state awaits! HEAVEN 17 A disc incorporating elements of dub, electro, ambient, house, drum & bass, techno, breakbeat, tribal and world musical styles in an array of tempos and timbres. TREMOR The first all drum & bass soundisc. New, fresh drum breaks and loops join up in seismic proportions with genetically enhanced bass tones and riffs - you have been warned! DARWIN CHAMBER A disc filled with clean 303, 808 and 909 elements and loops. Also includes a vast array of effect sweeps and fills, along with acoustic drum kits, wah guitar, turntable scratches and vocoder vocals. SMOKE A collection of superb quick and down tempo breaks support the sultry vibe from guitars, keyboards, pads and effects in this trip-hop feast.

Page 4 of 4