The SetupInf dialog box will appear.
You are now ready to install the driver.
Set the UA-3FXs ADVANCED (mode select) switch to the ON position. Use the USB cable to connect the UA-3FX to your computer.
This unit is equipped with a protection circuit. A brief interval (a few seconds) after connecting a USB connector is required before the unit will operate normally.
The Found New Hardware Wizard will appear.
Make sure that the screen indicates EDIROL UA-3FX , select Install from a list or specific location (Advanced), and click [Next].
The screen will indicate Please choose your search and installation options.
Select Dont search. I will choose the driver to install, and click [Next].

UA-3FX_e.book 18

Make sure that the Model field indicates EDIROL UA-3FX , and click [Next].
Driver installation will begin. * If the Driver Signing Options setting is not set to Ignore in step 4, the Install Hardware dialog box will appear. If the [Continue Anyway] button is displayed, click [Continue Anyway] to continue the installation. If you are unable to continue, click [STOP Installation] or [OK], and try the driver installation once again from step 1.
The Insert Disk dialog box will appear.

Click [OK].

The Insert Disk dialog may not appear. In that case, proceed to step 17.
The Files Needed dialog box will appear. Input the following into the Copy files from field, and click [OK].
D:\Driver\USB_XP2K\WDM * The drive name D: may be different for your system. Specify the drive name of your CD-ROM drive. * If the Driver Signing Options setting is not set to Ignore in step 4, the Install Hardware dialog box will appear. Click [Continue Anyway] to continue the installation.
The Completing the Found New Hardware Wizard will appear.
Verify that EDIROL UA-3FX is displayed, and click [Finish].
When driver installation has been completed, the System Settings Change dialog box will appear.
Click [Yes]. Windows will restart automatically.
Next, you need to make the driver settings. ( Settings and checking (p. 22))

UA-3FX_e.book 19

Windows 2000 users
Disconnect all USB cables except for a USB keyboard and USB mouse (if used).

The UA-3FX will operate in this mode when the ADVANCED mode is turned ON. ( Refer to "ADVANCED (mode select) switch" (p. 13)) The special driver included on the CD-ROM will be used, allowing audio to be recorded/played/edited with high quality and stable timing. In Advanced mode, audio signals can be transferred between the UA-3FX and the computer at a resolution of 16 / 24 bits and sampling frequencies of 32 / 44.1 / 48 kHz. Select Advanced mode if you are using an application that is able to record/playback/edit highquality audio, such as a 24 bit audio application or an ASIO-compatible application such as Cubase VST, Logic Audio, and Metro. In Advanced mode, the UA-3FX cannot play back audio data (audio CDs or warning sounds) from the Macintosh sound manager. ( "Installing the special driver" (Windows p. 16, Macintosh p. 28)

UA-3FX_e.book 27

The UA-3FX will operate in this mode when the ADVANCED mode is turned OFF. ( Refer to "ADVANCED (mode select) switch" (p. 13)) The standard USB audio driver included with MacOS will be used. In standard driver mode, audio signals are transferred between the UA-3FX and the computer at a resolution of 16 / 24 bits and sampling frequencies of 32 / 44.1 / 48 kHz. Select this mode if you are using an application that uses MacOSs own functionality, such as an application that uses the computers CD-ROM drive to play back CD-audio, or an application that uses the software synthesizer included with MacOS. The standard driver included with MacOS does not support ASIO. ( "Installing the OS-standard driver" (p. 54))
The installation procedure will differ depending on your system. Please proceed to one of the following sections, depending on the system you use. Mac OS X users..(p. 28) Mac OS 9 users..(p. 31)

UA-3FX_e.book 28

Mac OS X users
Installing the special driver
Disconnect all USB cables other than those for your keyboard and mouse, and restart your Macintosh.

In the Driver (Mac OS X) folder of the CD-ROM, double-click UA3FXUSBDriver.pkg.
In the Authenticate dialog box, input the password and click [OK].
The display will indicate Welcome to the EDIROL UA-3FX USB Driver Installer.

Click [Continue].

The display will indicate Select a Destination.
Click the drive in which the operating system is installed to select it, and then click [Continue].
The display will indicate Easy Install.
Click Install or Upgrade.
The display will indicate Installing this software requires you to restart your computer when the installation is done.
Click [Continue Installation].
The display will indicate The software was successfully installed.
Click [Restart] to restart your computer. This completes installation of the UA-3FX driver.

UA-3FX_e.book 29

Setting the audio device
Use the USB cable to connect the UA-3FX to your Macintosh. Open System Preferences and click Sound.
In the Sound Effects tab, set Play alerts and sound effects through to EDIROL UA-3FX 44.1kHz.
Although 44.1 kHz is used for the purpose of explanation within this document, this changes depending on the actual setting of the sampling frequency select switch on your UA-3FX.
In the Output tab, set Choose a device for sound output to EDIROL UA3FX 44.1kHz.
In the Input tab, set Choose a device for sound input to EDIROL UA-3FX 44.1kHz.
When you have finished making settings, close the dialog box.
Once set this way, all sounds from your Macintosh (including audio alerts) will be output only through the UA-3FX , not from the speakers of your Macintosh.

UA-3FX_e.book 30

When using the UA-3FX with your software
Please note the following points
Before using the UA-3FX with your software, please note the following points. * Connect the UA-3FX to your computer via a USB cable before you start up your sequencer or other software. * Do not disconnect the UA-3FXs USB cable while your sequencer or other software is running. * Exit your sequencer software before you unplug the UA-3FXs USB cable. * Leave the Sleep function of your Macintosh turned off. * The UA-3FX will not work in the Classic environment of Mac OS X. Use the UA-3FX when the Classic environment is not running.
Select EDIROL UA-3FX 44.1kHz in the audio driver setting of your software. For details, refer to the manual that came with your software.

UA-3FX_e.book 31

Mac OS 9 users
Installing the UA-3FX driver
With the UA-3FX disconnected, start up Macintosh.
If you are using a virus checker or similar software, be sure to exit this as well.
Insert the CD-ROM into the CD-ROM drive.
Double-click the UA-3FX Driver-E Installer icon (found in the Driver E (Mac OS 9) folder of the CD-ROM) to start up the installer. Verify the Install Location, and click [Install].

LINE OUT

Headphones

Signal flow

UA-3FX_e.book 34

Recording a cassette tape or LP into your computer
Heres how you can record the analog output of an audio device such as a cassette tape or LP (vinyl record) into your computer.

fig.analog.e

Audio cables To obtain the best audio quality, do not connect anything to the mic input jack or guitar/mic input jack. Lower the guitar/mic input adjustment slider to the lowest position.
Audio Amplifier (Cassette, record players)
Set this to match the sampling frequency of the recording software you are using.

Set this to ANALOG

Set this as high as possible without causing the line input level indicator to light.
Sampling frequency select switch Set this to the sampling frequency that is selected in your recording software. After you change the position of the sampling frequency select switch, you will need to disconnect and reconnect the USB cable. Recording source select switch Set this to ANALOG. Turn down the volume of your connected monitor speakers (or similar equipment) before you change the setting of the recording source select switch. Line input adjustment slider Use this to adjust the input level. In order to obtain the best audio quality, raise the slider until the level is as high as you can get it without causing the LED located above the slider to light in red.
Be careful of looped connections

Loop Connection

Stereo Set (cassette player)

fig.loop.e

OUTPUT

LINE IN

If you connect the UA-3FX as shown in the above diagram with another device that passes the input audio back to the output (e.g., a MD/DAT in recording mode), the sound will loop between the UA-3FX and the other device, causing oscillation and producing an unexpected high volume. Be aware that such connections can cause malfunctions or damage your speakers.

UA-3FX_e.book 35

Recording sound from your computer onto MD or DAT
Heres how you can record audio data from your computer onto a digital device such as MD or DAT.

fig.digital.e

Set this to match the sampling frequency of the audio data you are playing, the sampling frequency that can be recorded by your digital device (MD/DAT), and the sampling frequency used by your software. Optical digital cable

DIGITAL INPUT

MD/DAT

DIGITAL OUT

Signal flow Set this to LOOP-BACK

Sampling frequency select switch Set this to the sampling frequency of the audio data you are playing and the sampling frequency of your recording software. After you change the position of the sampling frequency select switch, you will need to disconnect and reconnect the USB cable. Recording source select switch Set this to LOOP-BACK. With the LOOP-BACK setting, audio signals will not be input from the various analog inputs. This means that only the sound from the computer will be output from the digital output connector, and no noise will enter the output. Turn down the volume of your connected monitor speakers (or similar equipment) before you change the setting of the recording source select switch. Other notes Do not connect anything to input jacks you are not using. * The UA-3FX does not support professional digital audio device formats. * The UA-3FX cannot mix the input signals from the various input jacks with the input signal from the digital input jack and output them from the digital output jack.

UA-3FX_e.book 36

Recording the digital output from a CD/MD/DAT into your computer

fig.digital2.e

Set this to the sampling frequency of your recording software and the sampling frequency of your digital playback device. Optical digital cable

CD player

DIGITAL IN

Set this to DIGITAL

Sampling frequency select switch Set this to the sampling frequency of your recording software. Normally, you will select 48 kHz or 44.1 kHz for DAT, and 44.1 kHz for MD or CD. For details, refer to the owners manual for your digital audio device and software. After you change the position of the sampling frequency select switch, you will need to disconnect and reconnect the USB cable. Recording source select switch Set this to DIGITAL. Turn down the volume of your connected monitor speakers (or similar equipment) before you change the setting of the recording source select switch. * The UA-3FX complies with SCMS. If the audio data that is input from the digital audio input connector contains copy-prohibit flags (as will be the case if you recorded an MD from a CD), the UA3FX will not allow this data to be recorded on your computer. (The sound will be output from the line output jacks and headphone jack.) * If you want to input sound from the line input jacks or the guitar/mic input jack, refer to Recording a cassette tape or LP into your computer (p. 32). The UA-3FX cannot mix the sounds from these inputs with the input from the digital input connector for recording. * If no signal is being received from the digital input connector even though the recording source select switch is set to DIGITAL, the UA-3FX will operate in the same way as when the switch is set to ANALOG.

UA-3FX_e.book 43

Applying effects
The UA-3FXs effects provide an easy way to change the character of the sound, and are a great convenience for audio editing. Three types of digital effect are provided, and these can be applied while you play back sound or record from a mic or guitar. You can use the four knobs to easily adjust the character of the effect that is applied to the mic, guitar, or the sound from the line inputs or digital input. * Before you continue, make connections and basic settings as described in Basic use (p. 33).

Advanced effects

Advanced 1 Three ways to use
1. MASTERING Old analog sources such as cassette tape will be given new life by digital technology. 2. LISTENING This setting is ideal for listening. Your computer becomes an AV processor, allowing you to enjoy karaoke. 3. PERFORM Enjoy powerful guitar sounds, and seven types of narration voice.

fig.fx-vari.e

Advanced 2 Use the four effect knobs to adjust the sound

fig.eng-panel

Advanced 3 Apply effects to the recording or playback

fig.rec-play.e

UA-3FX_e.book 44
Applying effects to the recording

fig.eng-panel1_50

ig.advance-fx1.e

Capture

Play back

ADVANCED

Advanced effect
Applying effects to the playback

fig.eng-panel2_50

fig.advance-fx2.e

Audio CD

Internet radio

Center cancel ADVANCED

UA-3FX_e.book 45

fig.fx-sw

Use the effect variation switch to select the desired effect.
Press the capture button or the playback button.
No effect will be applied if neither the capture button or the playback button are turned on (lit). You cannot turn both buttons on simultaneously.

fig.eng-panel1

If you want to apply effects to the sound being recording, turn on the capture button.

fig.eng-panel2

If you want to apply effects to the sound being played back, turn on the playback button.
Use the effect knobs to adjust the character of the effect.
If an effect knob is set to the OFF position, that effect will not be applied. Gradually turn the effect knob toward the right to adjust the setting to your taste.

Eliminates the vocal part from the CD audio played by your computer.

UA-3FX_e.book 51

Performance effect
It is useful to apply this effect when you are recording a mic or guitar.
fig.fx-master-3.e Set to 3.PERFORM

fig.fx-master2-3.e

Effect FX VOICE

FX GUITAR

Chorus Delay
Explanation Modifies the pitch, giving the sound a completely different character. As you turn the effect knob from OFF toward the maximum (far right), the pitch will rise. Distorts the sound to create guitar tones ranging from tasteful to extreme. Turning the effect knob from OFF toward the center position will produce a mild overdriven sound. Turning the knob from the center toward the maximum (far right) will produce more extreme distortion. Adds depth and spaciousness to the sound, creating a rich sense of stereo. Adds repeated delays to give the sound more depth, or produce an echo-like effect.

UA-3FX_e.book 52

Adding variation to your sound
Heres how you can apply effects to the sound from your guitar or mic.

fig.fx-master5.e

Monitor speakers Plug-in powered mic

3 Turn on the Capture

button

Set to 3.PERFORM

Set to ANALOG Produces a mild overdriven sound. Produces an aggressively distorted sound.
1 Set the input level as high as
possible without causing the guitar/mic input peak indicator to light.
Turn toward the right to raise the pitch.

Apply a chorus effect.

Apply an echo effect.

UA-3FX_e.book 53

A slightly distorted sound, as if you were speaking through a megaphone

fig.fx-temp7

3.PERFORM
Disguises the voice; useful for anonymous interviews

fig.fx-temp8

A nice setting for a guitar solo

fig.fx-temp9

A nice setting for clean guitar

fig.fx-temp10

UA-3FX_e.book 54
Installing the OS-standard driver
The procedure for installation and settings will depend on your system. Proceed to the appropriate section as follows. Windows XP/2000 users.(p. 54) Windows Me users..(p. 54) Windows 98 users.(p. 55) Mac OS X Users..(p. 58) Mac OS 9 Users..(p. 58)

Windows XP/2000 users

1. With the UA-3FX disconnected, start up Windows. Disconnect all USB cables except for a USB keyboard and USB mouse (if used). Exit all currently running software (applications). If you are using a virus checker or similar software, be sure to exit it as well. Place the UA-3FXs ADVANCED (mode select) switch in the OFF position. Use the USB cable to connect the UA3FX to your computer. The UA-3FX will be detected automatically, and the driver will be installed.

Windows Me users

1. With the UA-3FX disconnected, start up Windows. Disconnect all USB cables except for a USB keyboard and USB mouse (if used). Exit all currently running software (applications). If you are using a virus checker or similar software, be sure to exit it as well. Place the UA-3FXs ADVANCED (mode select) switch in the OFF position. Use the USB cable to connect the UA3FX to your computer.

If the Windows CD-ROM is not inserted in the CD-ROM drive, a Insert Disk dialog box may appear. In this case, insert the Windows CD-ROM into the CD-ROM drive and click [OK].

UA-3FX_e.book 56

Installing the OS-standard driver 10. When installation of the USB Composite Device driver is completed, a dialog box like the one shown here will appear. Click [Finish].

Volume Control setting

If you installed the standard Windows driver, set the Windows volume control.
If the Volume Control is not installed on your computer, use the Control Panel icon Add or Remove Programs to install it. For details on installation, refer to the Windows manual or Help.
11. Next, the USB audio device will be detected automatically, and the Add New Hardware Wizard dialog box will appear. Click [Next], and proceed with the installation in the same way as in steps 811 (p. 55). 12. When installation of the USB audio device driver is complete, a dialog box like the one shown here will appear. Click [Finish].
If Mute is checked or if the slider is lowered all the way, no sound will be output from the UA3FX.
Open the Volume Control. Click the Windows Start button, and select Programs | Accessories | Entertainment | Volume Control. Raise or lower the slider to adjust the volume of the UA-3FX.
You will be able to use the UA-3FX at the best audio quality if you set the Volume Control volume to the maximum setting.
Items that can be set CD Player (CD Audio) Controls the volume of audio CDs on the internal CD-ROM drive of the computer. (*1) Controls the volume of sound output from the EDIROL UA-3FX audio output device. Digital output and analog output will change. Controls the volume of the software synthesizer built into Windows.
Installation of the USB composite device driver and USB audio device driver has been completed. Restart Windows. 13. Set the Default Device for Sound Recording and Playback as follows.
(refer to Settings and checking (p. 22))

Synthesizer SW Synth

* 1 If the CD playback volume does not change when you adjust this control, then change the WAVE volume.

UA-3FX_e.book 57

When playing audio CDs from the computers internal CD-ROM drive, or using the UA-3FX to play game music (Standard driver mode only)
Windows XP/2000 users: 1. Open the System Properties dialog box. Select Start | Settings | Control Panel, and in the Control Panel, double-click the System icon. (Windows XP Click the Windows start button, and from the menu that appears, select Control Panel.) Open the Device Manager. Click the Hardware tab, and click the Device Manager button. Open the CD-ROM drives Properties. In CD-ROM drive, double-click the CD-ROM drive that you are using. In Digital CD Playback, check the Enable digital CD audio for this CD-ROM device item.

No sound

Is the UA-3FXs Recording source select switch set to ANALOG? When the Recording source select switch is set to DIGITAL, the audio signals input to the digital Input connector are output. The computers audio data is not output. Are you attempting to use the CD player of your computer to play an audio CD? If you wish to play an audio CD on the CD-ROM drive of your computer, refer to When playing audio CDs from the computers internal CD-ROM drive, or using the UA-3FX to play game music (Standard driver mode only) (p. 57). Are you running multiple applications? If multiple applications are running simultaneously, an error message may appear. If this occurs, click [OK], and close the other applications. Even if an application window is closed, it is still running if it remains in the taskbar, so be sure to quit any unneeded applications shown in the taskbar. Have you specified the audio data output destination for your operating system? You must specify the UA-3FX as the audio data output destination for your computer. Have you specified the audio data output destination for your playback software? For some software such as Cool Edit Pro LE, you must set the audio data output destination as UA-3FX. For details on this setting, refer to the owners manual for the software. Have the drivers been installed correctly? In order to playback audio data using the UA-3FX, the USB Audio Device driver must be installed. For details on installation and settings, refer to Getting Connected and Installing Drivers (Windows) (Windows p. 14, Macintosh p. 26). Are the faders of the Volume Control raised? Adjust the volume of each fader as described in Volume Control setting (p. 56). Are the faders of the Macintosh volume control raised? Adjust the volume as described in Adjusting the Sound Input/Output (p. 59). If you are using Mac OS X, some system sound input/output settings may cause there to be no sound from the Macintosh speakers. Select the internal speakers in the Output tab and Input tab.

UA-3FX_e.book 63

Sound is distorted
Could the peak indicator be lighting in red? If you are inputting sound from the line input jack, use the UA-3FX's line input adjustment slider to lower the input level. If you are inputting sound from a guitar or mic, use the UA3FX's guitar/mic input adjustment slider to lower the input level. The number of guitar/mic input peak indicator LEDs that light will depend on the UA-3FX's output level. If the red LED lights, use the line output volume control to lower the volume. Could you be applying effects? Some types of effect may cause the sound to distort if applied too strongly. If this occurs, try lowering the input level using the line input adjustment slider or the guitar/mic input adjustment slider. Alternatively, turn the effect knob toward the left to lessen the effect.
Insufficient volume from a device connected to the line input jacks

Could you be using a cable that contains a resistor? Use a cable that does not contain a resistor (such as one from the Roland PCS series). Is the line input adjustment slider raised appropriately? Raise the slider as high as possible without causing the line input peak indicator to light.
Can't use 5.1 ch surround playback
5.1 surround playback is supported only in Windows. Are you using Advanced mode? You must use Advanced mode in order to enjoy 5.1 ch surround playback. To do so, you will need to turn the UA-3FX's ADVANCED (mode select) switch ON, and install the driver. Are you using WinDVD 5 or later? Please use WinDVD 5 or a later version. We recommend that you install the most recent update. Have you set the audio input/output destination settings correctly? Specify the UA-3FX as the audio input/output destination. ( Specifying the audio input/output destination (p. 22))

UA-3FX_e.book 64

Noise is heard when playing back audio
Is a mic still connected? If a mic is connected to the UA-3FX, use the Guitar/Mic input adjustment slider to lower the input level. Could there be a connection loop? On some computers, if a USB-connected MIDI sound module and the UA-3FX are connected to the same computer via USB, and the output of the MIDI sound module is connected to the UA-3FX's line input jacks, noise from the computer may be heard from the UA-3FX via the MIDI sound module. If this occurs, you can either use a self-powered hub to connect the MIDI sound module and the UA-3FX in parallel, or connect the MIDI sound module via a serial connection or a MIDI interface. This problem may be solved by properly grounding the chassis of your computer, or the ground prong of the plug on the AC power cord that was supplied with your computer. Also, make sure that there are no devices nearby that emit a strong magnetic field, such as a television or a microwave oven. Are a large number of audio devices connected? If a large number of audio devices are connected, noise may occur. Do not connect audio devices that you are not using. If the sound is interrupted during audio playback, you may hear a soft pop noise. Also refer to the following section, Sound is interrupted during audio playback.
Sound is interrupted during audio playback
Graphic accelerators may cause noise to be heard during audio playback. Use the following procedure to set graphic acceleration to None. 1. In the Windows Control Panel, double-click Display to open the Display Properties dialog box, and click the Settings tab. 2. Click Advanced to open properties, and click the Performance tab. 3. In the Graphics section, set the Hardware acceleration slider to None, and then click [OK]. 4. In the Display Properties dialog box, click [OK] to close the dialog box. 5. Then restart your computer. The sound may be interrupted if a wireless LAN is operating. Try disabling the wireless LAN in the Device Manager. If this solved the problem of sound being interrupted, you may be able to solve the problem of interrupted sound by updating the driver or BIOS. Are many applications running on your computer? If you use numerous applications during playback, or start up another application, the playback may be interrupted depending on your computer system. Exit all unneeded applications, and try again. If this does not resolve the problem, try restarting your computer.

fig.block-digital_e

Digital output connector (optical) Line output volume Effects CAPTURE Effects PLAYBACK Headphone jack
Degital input connector (optical)

Input Monitor switch

Line output jacks Output level indicators
When the recording source select switch is set to LOOPBACK

fig.block-loop_e

Digital output connector (optical) Line output volume Effects CAPTURE / PLAYBACK Headphone jack

UA-3FX_e.book 74

Advanced... 14 ADVANCED (mode select) switch. 13 Advanced effects.. 43 Advanced mode.. 14, 41 ASIO.. 32, 41 ASIO Direct Monitor.. 41 LISTENING...

43, 49

MASTERING.. 43, 46 Mic input jack.. 10
OS-standard driver.. Output level indicators.
Block Diagram.. Buffer Size..
P playback... 44 Playback button.. 12 plug-in powered mic.. 10

PERFORM.. Performance..

Capture button..
Digital input connector.. Digital output connector.. Direct Monitor..
recording.. 44 Recording source select switch.
Effect knobs.. 12 Effect variation switch.. 11 effects... 43, 45

..11, 3437, 39 S

Sampling frequency select switch.. Standard driver mode..
Guitar/mic input adjustment slider.. 12, 38 Guitar/mic input jack.. 13 Guitar/mic input peak indicator. 12

..11, 3437, 11 12

USB connector.. USB indicator..

Headphone jack...

Input Monitor select switch. 41 Input monitor switch.. 13 Input select switch. 11, 37
Latency.. 41 Line input adjustment slider. 12, 34 Line input jacks.. 10 Line input peak indicator.. 12 Line output jacks.. Line output volume..

UA-3FX_e.book 75

For EU Countries This product complies with the requirements of European Directive 89/336/EEC.

For the USA

FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) This device must accept any interference received, including interference that may cause undesired operation. Tested To Comply With FCC Standards

FOR HOME OR OFFICE USE

Unauthorized changes or modification to this system can void the users authority to operate this equipment. This equipment requires shielded interface cables in order to meet FCC class B Limit.

For Canada

NOTICE
This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations.
Cet appareil numrique de la classe B respecte toutes les exigences du Rglement sur le matriel brouilleur du Canada.
DECLARATION OF CONFORMITY Compliance Information Statement
Model Name : Type of Equipment : Responsible Party : Address : Telephone :
UA-3FX USB Audio Interface Edirol Corporation North America 425 Sequoia Drive, Suite 114, Bellingham, WA 98226 (360) 594-4276

Information

When you need repair service, call your nearest EDIROL/Roland Service Center or authorized EDIROL/Roland distributor in your country as shown below.

HONG KONG BARBADOS

A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St.Michael, Barbados TEL: (246)430-1100
Audionet Distribuciones Musicales SAC Juan Fanning 530 Miraflores Lima - Peru TEL: (511) 4461388

IRELAND

Roland Ireland G2 Calmount Park, Calmount Avenue, Dublin 12 Republic of IRELAND TEL: (01) 4294444

CYPRUS

Radex Sound Equipment Ltd. 17, Diagorou Street, Nicosia, CYPRUS TEL: (022) 66-9426

EUROPE

EDIROL (Europe) Ltd. Studio 3.Power Road London W4 5PY U. K. TEL: +44 (0)5949 FAX:+44 (0)5948 http://www.edirol.com/europe Deutschland TEL: 20 France TEL: 371 Italia TEL: 02 93778329
Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T.S.T, Kowloon, HONG KONG TEL: 2333 1863
Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Dr. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051

BRAZIL

Roland Brasil Ltda. Rua San Jose, 780 Sala B Parque Industrial San Jose Cotia - Sao Paulo - SP, BRAZIL TEL: (011) 4615 5666
MOCO INC. No.41 Nike St., Dr.Shariyati Ave., Roberoye Cerahe Mirdamad Tehran, IRAN TEL: (021) 285-4169
Roland Italy S. p. A. Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300

TRINIDAD

AMR Ltd Ground Floor Maritime Plaza Barataria Trinidad W.I. TEL: (868)638 6385
Comercial Fancy II S.A. Rut.: 96.919.420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540

NORWAY

Roland Scandinavia Avd. Kontor Norge Lilleakerveien 2 Postboks 95 Lilleaker N-0216 Oslo NORWAY TEL: 2273 0074

GUATEMALA

Casa Instrumental Calzada Roosevelt 34-01,zona 11 Ciudad de Guatemala Guatemala TEL:(502) 599-2888
BELGIUM/FRANCE/ HOLLAND/ LUXEMBOURG
Roland Central Europe N.V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811
Roland Iberia, S.L. Paseo Garca Faria, 33-Barcelona SPAIN TEL: 91 00

AFRICA

Al Fanny Trading Office 9, EBN Hagar A1 Askalany Street, ARD E1 Golf, Heliopolis, Cairo 11341, EGYPT TEL: 20-2-417-1828
Badie Studio & Stores P.O. Box 62, Doha, QATAR TEL: 423554

THAILAND

Theera Music Co. , Ltd. 330 Soi Verng NakornKasem, New Road, Sumpantawongse, Bangkok 10100, THAILAND TEL: (02) 224-8821

HONDURAS

Almacen Pajaro Azul S.A. de C.V. BO.Paz Barahona 3 Ave.11 Calle S.O San Pedro Sula, Honduras TEL: (504) 553-2029

CZECH REP.

K-AUDIO Kardasovska 626. CZ-Praha 9, CZECH REP. TEL: (2) 666 10529

SWEDEN

Roland Scandinavia A/S SWEDISH SALES OFFICE Danvik Center 28, 2 tr. S-Nacka SWEDEN TEL: (0)00 20

SAUDI ARABIA

aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg., 1st Floor, Alkhobar, SAUDI ARABIA P.O.Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081

REUNION

Maison FO - YAM Marcel 25 Rue Jules Hermann, Chaudron - BP491 Ste Clotilde Cedex, REUNION ISLAND TEL: (0262) 218-429

VIETNAM

SAIGON MUSIC DISTRIBUTOR (TAN DINH MUSIC) 138 Tran Quang Khai Street Dist. 1, Ho Chi Minh City VIETNAM TEL: (08) 848-4068

MARTINIQUE

Musique & Son Z.I.Les Mangle 97232 Le Lamantin Martinique F.W.I. TEL: 426860 Gigamusic SARL 10 Rte De La Folie 97200 Fort De France Martinique F.W.I. TEL: 715222

DENMARK

Roland Scandinavia A/S Nordhavnsvej 7, Postbox 880, DK-2100 Copenhagen DENMARK TEL: 3916 6200

SWITZERLAND

Roland (Switzerland) AG Landstrasse 5, Postfach, CH-4452 Itingen, SWITZERLAND TEL: (061) 927-8383
Technical Light & Sound Center Rawda, Abdul Qader Jazairi St. Bldg. No. 21, P.O.BOX 13520, Damascus, SYRIA TEL: (011) 223-5384

SOUTH AFRICA

Paul Bothner(PTY)Ltd. Royal Cape Park, Unit 24 Londonderry Road, Ottery 7800 Cape Town, SOUTH AFRICA TEL: (021) 799 4900

FINLAND

Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)24 020

UKRAINE

TIC-TAC Mira Str. 19/108 P.O. Box Munkachevo, UKRAINE TEL: (03131) 414-40

AUSTRALIA/ NEW ZEALAND

AUSTRALIA/ NEW ZEALAND Roland Corporation Australia Pty.,Ltd.

FOR IMMEDIATE RELEASE Contact: Tara Callahan Roland Corporation US tarac@rolandus.com 323-890-3718
EDIROL BY ROLAND RELEASES LEOPARD COMPATIBLE DRIVERS Los Angeles, CA, November 1, 2007In coordination with Apples October 26 Leopard roll-out, Roland is proud to announce full Mac OS 10.5 (Leopard) compatibility for 38 EDIROL products after releasing driver updates earlier this month. EDIROL by Roland Product Manager Michael Barrett explains, We are always striving to equip our customers with the latest, most up-to-date technology as it happens. Were thrilled that we were able to synchronize our own research and development efforts with the release of the Leopard operating system. These new driver updates give our Mac users access to all of the operational improvements intrinsic in Mac OS 10.5, and will help to simplify the creative process. The Leopard compatible list includes the following EDIROL devices: EDIROL Supports Mac OS 10.5 (Leopard) USB 2.0 Audio Devices: M-16DX, UA-101 USB 2.0 mode, UA-1000 USB 1.1 Audio Devices: M-100FX, PCR-1, PCR-A30, SC-D70, SD-90, UA-1EX, UA-3FX, UA-4FX, UA-5, UA-20, UA-25, UA101 USB 1.1 mode, UA-700, UR-80 USB MIDI Devices: UM-1 Series, UM-2 Series, UM-3EX, UM-550, UM-880, PC-50, PC-300, PCR-300, PCR-500, PCR800, PCR-M1, PCR-M30, PCR-M50, PCR-M80, PCR-30, PCR-50, PCR-80, SC-8820, SC-8850, SD20, SD-80, SK-500 The FA-101 and FA-66 FireWire audio interfaces use Apples native drivers built into the Macintosh OS X platform, including Leopard.
* Existing EDIROL MIDI Drivers were tested and found to be fully compatible with Mac OS 10.5. * Please check the Leopard compatibility of your audio/MIDI application and its system requirements when you use your EDIROL audio/MIDI device with Mac OS 10.5. Roland is a world leader in the design, manufacture and distribution of electronic musical instruments, professional audio equipment, multimedia products and music accessories. For more information, contact Roland Corporation U.S., 5100 S. Eastern Ave., P.O. Box 910921, Los Angeles, CA 90091-0921, (323) 890-3700 (x3718 - for media use only), www.RolandUS.com/EDIROL.