RYOBI 12 in. (305 mm) DRILL PRESS MODEL NO. DP120 REPAIR SHEET
RYOBI 12 in. (305 mm) DRILL PRESS MODEL NUMBER DP120 FIGURE A
RYOBI 12 in. (305 mm) DRILL PRESS MODEL NUMBER DP120
The model number will be found on a plate attached to the motor housing. Always mention the model number in all correspondence regarding your Drill Press or when ordering repair parts.

PARTS LIST FOR FIGURE A

Key No. 29 Part Number 13401001 TDP12B03008 13401002A TDP12B03011 13201010A 16101009A 13401003A 13401004B 13401011A 16101013B TDP12B03002 13406002A 13406001 TDP12B03009 13401014B TDP12B02001 TDP12B13103006M-1 13103006M TDP12B02002 Description Qty.
BASE..... 1 * SCREW, HEX HEAD (M10 X 25 mm)... 4 BASE COLLAR.... 1 * SCREW, HEX HEAD (M8 X 8 mm)... 5 GEAR RACK..... 1 TABLE CRANK HANDLE.... 1 TUBE COLUMN/PEDESTAL... 1 TABLE SUPPORT W/SCALE... 1 GEAR..... 1 ELEVATION WORM.... 1 COLUMN COLLAR.... 1 TABLE CLAMP.... 2 * SCREW (M4 X 6 mm).... 3 INDICATOR FOR TABLE... 1 SHAFT GEAR.... 1 TABLE ARM..... 1 SCALE FOR BRACKET.... 1 * SCREW, HEX HEAD (M12 X 25 mm)... 1 TABLE.... 1 SPINDLE HOUSING.... 1 GASKET.... 1 BEARING BALL..... 2 LOCKING RING..... 1 CHUCK TOOL.... 1 CHUCK KEY.... 1 CHUCK..... 1 ARBOR..... 1 SPINDLE..... 1 BEARING..... 1
* Standard Hardware Item May Be Purchased Locally 3
RYOBI 12 in. (305 mm) DRILL PRESS MODEL NUMBER DP120 FIGURE B

SEE NOTE

NOTE: The assembly shown represents an important part of the double insulated system. To avoid the possibility of alteration or damage to the system, service should be performed by your nearest Ryobi Authorized Service Center. For the service center nearest you call 1-800-525-2579. 4

Key No. 76

Part Number 16102010G-1 16102010G TDP07005 13202009F TDP07001 13202008B-1 TDP07001 TDP13204005A 13304011C 13402005 13206007J TDPTDP12BTDP01001 TDP11002 13302016Y TDP06001 YCG77S4-01 TDP06002 TDPTDP12B03007 13406008A 16103011A TDP07002 TDP12B20001 13302015B-3 13402001D TDPTDP16104007A TDP12B06005 089140300082

PARTS LIST FOR FIGURE B

Description Qty. SWITCH KEY.....1 SWITCH....1 TAPPING SCREW (ST 4.2 X 9.5 mm)...2 SWITCH PLATE....1 SCREW (M5 X 14 mm)....2 SWTICH HOUSING....1 SCREW, PAN HEAD (M5 X 6 mm)...2 LOCK WASHER....2 STROKE INDICATOR....1 STOP PIN.....1 DEPTH STOP SCALE RING...1 DEPTH STOP RING....1 HUB....1 FEED HANDLE....3 KNOB.....3 TENSION KNOB....3 WARNING LABEL....1 ROLL PIN....2 BELT TENSION HANDLE....1 SHAFT RETAINER....1 MOTOR SUPPORT.....1 SCREW (M8 X 20 mm)....4 WASHER.....8 MOTOR CORD....1 HEX NUT.....4 MOTOR.....1 HEX NUT.....2 LOCK WASHER....2 MOTOR SUPPORT.....1 MOTOR SUPPORT.....1 ADJUSTING LEVER....1 SCREW (M8 X 16 mm)....1 DATA LABEL....1 KEY HOLDER....1 SCREW (M5 X 12 mm)....2 CORD TIE....1 POWER CORD....1 HEAD.....1 SCREW (M8 X 8 mm)....1 SPECIAL SET SCREW....1 HEX NUT.....1 SPRING SEAT....1 SPRING RETAINER.....1 TORSION SPRING....1 SPRING CAP....1 HEX NUT....2 CAPACITOR (DP120 MOTOR)....1 5
RYOBI 12 in. (305 mm) DRILL PRESS MODEL NUMBER DP120 FIGURE C

Key No. 98 99

Part Number TDP12B06001 13202014A TDP04001 TDPTDP12B11004 TDP12B03006 13405005A 13405007B 13405008A 13405000 13406009C 13406006F TDP10002 TDP02001 13302023A 13302022 13405006A 983000040 983000040R 02-07-06

PARTS LIST FOR FIGURE C

Description Qty.
CLAMP COVER..... 3 RUBBER BUSHING.... 2 NUT..... 3 CORD CLAMP.... 4 HEX WRENCH.... 1 * SCREW (M5 X 10 mm).... 4 FOAM WASHER.... 4 WASHER.... 4 * SCREW (M6 X 8 mm).... 4 MOTOR PULLEY.... 1 BELT..... 1 IDLER PULLEY.... 1 IDLER PIVOT..... 1 KNOB..... 1 PULLEY/BELT HOUSING.... 1 SPEED CHART.... 1 LOGO PLATE.... 1 SHAFT RETAINER.... 1 BEARING..... 2 SPACER.... 1 PULLEY INSERT.... 1 SPINDLE PULLEY.... 1 NUT.... 1 BELT..... 1 OPERATOR'S MANUAL REPAIR SHEET (REV:01)