RYOBI GAS CULTIVATOR MODEL NO. RY60511B REPAIR SHEET
RYOBI GAS CULTIVATOR MODEL NO. RY60511B
The model number will be found on a plate attached to the engine housing. Always mention the model number in all correspondence regarding your GAS CULTIVATOR or when ordering repair parts.

KEY NO. 27

PART NUMBER 678135001 * * *

PARTS LIST

DESCRIPTION QTY. GEAR BOX ASSEMBLY WITH TUBE.. 1 LINER - DRIVE TUBE.. 1 TINE A, OUTER RIGHT. 1 TINE B, INNER RIGHT.. 1 TINE C, INNER LEFT.. 1 TINE D, OUTER LEFT.. 1 FELT WASHER.. 2 CLEVIS CLIP.. 2 TINE SHIELD ASSEMBLY ( INC. KEY NOS. 19, 34 AND 48)..1 BOLT (1/4-20 X 1 in.).. 4 LOCK NUT (1/4-20). 9 RECEIVER RETAINER KNOB. 1 SCREW (M5 X 16 mm PAN HD.). 1 LOWER HANDLE ASSEMBLY (INC. KEY NO. 25 AND 47).. 1 KNOB (1/4-20).. 2 RECEIVER RETAINER ASSEMBLY. 1 CARRIAGE BOLT (1/4-20 X 2-1/4 in.). 2 ACORN NUT... 2 WARNING LABEL, FOOT.. 1 HANDLE BOLT (1/4-20 X 1.53 in.). 4 UPPER HANDLE ASSEMBLY (INC. KEY NOS. 25, 31, 46, AND 50). 1 THROTTLE CABLE ASSEMBLY (INC. KEY NO. 23).. 1 SWITCH.. 1 TRIGGER.. 1 PLASTIC CLIP.. 2 CLEVIS PIN.. 1 RETAINING RING.. 1 KEY NO. 50
PART NUMBER 983000886R 983000887 05-10-06 (REV:01)
DESCRIPTION QTY. TANK - BALLAST ASSEMBLY (INCLUDES KEY NO. 29).. 1 LOGO LABEL.. 1 MOUNTING BRACKET. 1 GRIP... 1 BALLAST TANK LID. 1 FLEXIBLE DRIVE SHAFT.. 1 WHEEL ACCESSORY LABEL. 1 * BOLT (10-24 X 1-1/4 in.).. 2 NUT (10-24).. 2 * SCREW (8-16 X 1/2 in.).. 1 WHEEL/DRAG STAKE ASSEMBLY (INCLUDES KEY NO. 39-44).. 1 FRAME ASSEMBLY. 1 DRAG STAKE... 1 QUICK RELEASE PIN.. 1 FLAT WASHER.. 2 WHEEL ASSEMBLY (7 in. DIA.). 2 PUSH CAP NUT (FITS 1/2 in.).. 2 WARNING HANG TAG.. 1 BOOM WARNING LABEL.. 1 STARTING LABEL.. 1 WARNING LABEL.. 1 PLASTIC ROPE CLIP.. 1 BOLT (1/4-20 x 5/8 in.). 1 OPERATORS MANUAL (960976001). 1 REPAIR SHEET REPLACEMENT PARTS LIST (960976002).. 1
* STANDARD HARDWARE ITEM MAY BE PURCHASED LOCALLY 3

FIGURE A

KEY NO. PART NUMBER DESCRIPTION QTY. KEY NO. 47 PART NUMBER DESCRIPTION QTY.
25.4 CYLINDER.. 1 PLATE.. 1 SCREW (M5 x 10 mm PAN HD.).. 2 GASKET.. 1 INSULATOR.. 1 NUT (M5 x.8 mm).. 2 SCREW (M5 x 31 mm PAN HD.).. 2 GASKET.. 2 CARBURETOR ASSEMBLY. 1 FILTER HOUSING ASSEMBLY. 1 SCREW (M5 x.8 x 60 mm PAN HD.).. 2 GASKET.. 1 MUFFLER ASSEMBLY. 1 SCREW (M5 x.8 x 50 mm PAN HD.). 2 CRANKCASE ASSEMBLY. 1 GASKET.. 1 SCREW (M5 x.8 x 22 mm).. 2 PULLEY ASSEMBLY.. 1 WOODRUFF KEY.. 1 ROTOR.. 1 NUT.. 1 WASHER.. 2 CLUTCH ASSEMBLY.. 1 WASHER, CURVED. 2
PRIMER.. 1 SCREW (M5 X 16 mm). 7 * SCREW (M6 x 1 x 14 mm PAN HD.). 2 COIL ASSEMBLY.. 1 SCREW (M4 x.7 x 22 mm PAN HD.).. 2 SPARK PLUG.. 1 FRONT HOUSING ASSEMBLY. 1 SCREW (M5 x.8 x 20 mm PAN HD.).. 4 STARTER HOUSING ASSEMBLY. 1 REAR ENGINE HOUSING. 1 * SCREW (M4 x 1.75 x 16 mm PAN HD.). 4 FUEL TANK.. 1 FUEL LINE.. 1 CLIP.. 1 CLIP.. 1 AIR FILTER.. 1 OUTER COVER ASSEMBLY.. 1 HEAT SHIELD.. 1 LOGO LABEL.. 1 PRIMER LABEL.. 1 RETAINER... 1 * SCREW (M4 X 16 mm TORX PAN HD.).. 1 FUEL CAP.. 1 SPARK ARRESTOR KIT (NOT SHOWN).. 1
* STANDARD HARDWARE ITEM MAY BE PURCHASED LOCALLY 5

PARTS LIST FOR FIGURE A

KEY NO. PART NUMBER DESCRIPTION QTY.
WRIST PIN CLIP RING....2 WASHER.....2 PISTON RING.....1 PISTON....1 NEEDLE BEARING (ID 8 X 8.8)...1 WRIST PIN....1