INSTRUCTIONS FOR THE POWER SUPPLY CORD
GENERAL INFORMATION....3 MACHINE.....4

ACCESSORIES......4

INSTALLATION....5
STARTING THE MACHINE.....5 MANUAL PRIMING OF THE WATER CIRCUIT....6 SETTING THE LANGUAGE AND THE CLOCK....6 "AQUA PRIMA" FILTER......7

DISPLAY.....8

CHOOSE COFFEE AROMA.....8

ADJUSTMENTS.....9

COFFEE INTENSITIY.....9 ADJUSTING THE HEIGHT OF THE DRIP TRAY....9 FILLING THE MILK CONTAINER.....9
BEVERAGE DISPENSING.....10
ESPRESSO / COFFEE / LONG COFFEE..... 10 DISPENSING BEVERAGES WITH GROUND COFFEE..... 11 HOT WATER DISPENSING..... 12 LATTE MACCHIATO..... 12 DISPENSING HOT MILK..... 13 ESPRESSO MACCHIATO..... 14 CAPPUCCINO..... 14
BEVERAGE PROGRAMMING.... 15
BEVERAGE PROGRAMMING MENU..... 15 ESPRESSO / COFFEE / LONG COFFEE PROGRAM..... 15 PROGRAMMING MILK BEVERAGES..... 16

MACHINE SETTINGS.....18

PROGRAMMING THE MACHINE.... 18 LANGUAGE MENU..... 19 CUP ILLUMINATION MENU..... 19 AQUA PRIMA FILTER MENU..... 19 WATER HARDNESS MENU..... 20 RINSE MENU..... 20 CUP WARMING PLATE MENU..... 21 ACCOUSTIC TONES AND ALARMS MENU.... 21 DISPLAY MENU..... 21 BEVERAGE SETTINGS......22 ADJUSTMENT OF THE COFFEE BREW TEMPERATURE.... 22 AROMA ADJUSTMENT FOR COFFEE BREWING.... 23 PREBREWING ADJUSTMENT (ONLY COFFEE BEVERAGES).... 23 ADDITIONAL FUNCTIONS.....24 COFFEE OF THE WORLD FUNCTION..... 24 DEMO MODE..... 26 BEVERAGE COUNTER FUNCTION..... 26 MAINTENANCE.....27 MILK CIRCUIT RINSE CYCLE..... 27 MILK CIRCUIT WASH CYCLE..... 28 COFFEE CIRCUIT CLEANING CYCLE (BREW GROUP WASH CYCLE )... 31 BLOCK DISPLAY..... 31 DESCALING...... 32 CLOCK SETTINGS.....34 TIME SETTING...... 34 AUTOMATIC TIMER SETTINGS.... 35 ENERGY SAVING SETTINGS..... 37 SPECIAL......38 FACTORY SETTINGS..... 38
CLEANING AND MAINTENANCE....39
GENERAL MACHINE CLEANING....39 MILK CONTAINER MAINTENANCE AND CLEANING.....40 CLEANING THE BREW GROUP.....42 GRINDER MAINTENANCE.....43
ERROR CODES.....44 TECHNICAL DATA.....45 SAFETY RULES.....46

GENERAL INFORMATION

TO ASSESS WATER HARDNESS, SEE "WATER HARDNESS MENU" ON PAGE 20.
MANUAL PRIMING OF THE WATER CIRCUIT
Manually prime the water circuit only when the following display appears. Note: rst make sure that the water tank is full.

priming the machine

Position a container under the hot water spout (it is possible that water will not come out of the spout).
Press the display once and the machine will begin priming the water circuit.
When the prime circuit cycle is nished, remove the container. The machine is now ready for use.
SETTING THE LANGUAGE AND THE CLOCK
When the machine is switched-on for the rst time, it requires the selection of the desired language. This allows you to adjust the parameters of the beverages to the typical parameters of the country where the machine is used. This is why some languages are differentiated also by country.

1deutsch

franais

Italiano (i)

2deutsch

3deutsch

language 1/2

english

italiano (ch)

nederlands

Select the desired language. Press for the other languages.
Press to select the desired language.

Press ok.

self-test
See manual on page 34 to adjust the clock.
The machine starts and displays the menu in the selected language.
If desired, the demo function (see page 26) may be activated by pressing the key, each time the machine carries out a self-diagnosis.

AQUA PRIMA FILTER

To improve the quality of the water used, install the "Aqua Prima" lter. After installation, go to the lter activation program (see programming). In this mode the machine advises the user when the lter must be replaced.
Remove the "Aqua Prima" lter from its packaging. Enter the date of the current month.
Insert the lter in its place within the empty tank (see gure). Press down until it clicks into place.
Fill the tank with fresh water. Let the lter soak for 30 minutes. After 30 minutes discard the water in the tank and rell with fresh water.

6machine

settings specials

beverage settings

main menu

extras

maintenance
show icon explanation my custom coffee programming menu
clock settings back to coffee menu

energy saving

Press "programming menu".
Press "machine settings".

language

cup illumination

not inserted

go back restore default settings save settings

activate

display alerts & acoustic settings

go back

machine settings

cup warmer

restore default settings

water hardness

rinsing

back to menu

inserted
Press "water lter".
Press "activate lter".
The machine then activates the "Aqua Prima" lter. Wait for the cycle to nish automatically. When the activation cycle ends, the machine proceeds to the choose beverage menu. NOTE: occasionally, the machine may not dispense the desired quantity of water for the correct water lter initialization. In this case, repeat the operations described from point 6 and following.

DISPLAY

It is possible to change the type of display and choose between " icon format" and "text format"

ICON FORMAT

hot milk

TEXT FORMAT

latte espresso macchiato cappuccino macchiato medium hot water long coffee medium medium strong

coffee medium

my custom coffee

espresso strong

programming menu

show icon explanation

show icon
Go to the "text format" menu

Beverage programming

Accessing the programming menu
Go to the "icon format" menu
To get the desired beverage, press the corresponding symbol on the display. The machine automatically performs all the necessary operations. To make 2 cups, press the beverage symbol twice. press twice

CHOOSE COFFEE AROMA

The intensity of the color on the cup icon (only valid for coffee beverages) indicates the aroma, or quantity of coffee to be ground, for preparing the beverage. The greater the quantity of coffee ground the stronger the coffee will taste.

medium

strong
When the machine is programmed to use pre-ground coffee or when a beverage is customized, the icon is displayed in a different way and/or accompanied by an asterisk (see section on programming beverages.)

pre-ground

customization

ADJUSTMENTS

COFFEE INTENSITIY
The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply turn the dial and you will notice that the coffee goes from mild intensity to strong intensity.

The display shows the conrmation of the saved settings, and the machine automatically returns to the main menu.

PROGRAMMING THE MACHINE

Some of the machines functions can be programmed to customize operations according to your own requirements.
Press the "programming menu" button. The programming menu will access: Programming the machine operations (see page 18) Special functions (see page 38) Maintenance (cleaning the machine) (see page 27)
machine settings beverage settings
In depth beverage programming (see page 22) Extra functions (see page 24) - Current date and time - Standby timer - Times to turn on/turn off over the span of a day (see page 34).

specials

maintenance energy saving

Activate standby

After having set each of the following menus, press - "go back" to return to the previous screen - "restore default settings" to restore the initial values - "save settings" to save the settings - "back to menu" to return to the main menu

MACHINE SETTINGS

When the machine settings are selected the following screen appears. Here you can: set the illuminate cups function. set the language of the menus. set the brightness of the display colors. set/activate the tones.

cup illumination water

set the machines operation through the Aqua Prima lter. set the water hardness. set the circuit rinse cycle.
set the operation of the cup warming plate.

LANGUAGE MENU

For changing the language of the display.

deutsch Italiano (i)

This function was described at the beginning of the manual. This setting is of fundamental importance for correctly adjusting the parameters of the machine according to the country where the machine is used. Press to display the next page.

CUP ILLUMINATION MENU

This function allows activating/ deactivating the dispensing area illumination. In this menu you can:

turn off illumination.

restore default settings save settings

turn on illumination.

AQUA PRIMA FILTER MENU
The "Aqua Prima" lter puries water and allows you to taste all the aroma of the coffee. In this menu you can:
proceed with the initialization (cleaning) of the water lter (see page 7). After initialization the insert option is activated. set the machine to operate with the Aqua Prima lter.
set the machine to operate without theAqua Prima lter.
Note: Press "activate lter" each time a new "Aqua Prima" lter is installed. Press "not inserted" when an "Aqua Prima" lter is not used. Press inserted when an Aqua Prima lter is used. This function operates even after pressing the activate lter button.

WATER HARDNESS MENU

To adjust the level of water hardness, shown on a scale of 1 to 4. The machine is preset at a hardness value of 3.
1 Immerse the water hardness strip included in the welcome pack for one second in water.
Check the value. The test can be used only for one measurement.
Press the "water hardness" button.
Set the water hardness on the machine by pressing + or go back restore default settings save settings back to menu

RINSE MENU

To clean the internal circuits for coffee brewing in order to guarantee that beverages are brewed with fresh water only. In this menu you can:
Note: This rinse cycle is performed every time the machine is turned on when it is cool.
deactivate the rinse cycle.
activate the rinse cycle.

CUP WARMING PLATE MENU

To activate the cup warming plate on the upper part of the machine. In this menu you can:

always on

keep the cup warming plate always on.
keep the cup warming plate off when the machine is in stand-by.

off in standby

keep the cup warming plate always off.
ACOUSTIC TONES AND ALARMS MENU
To activate/deactivate the machines acoustic tones. Pressing the button does not immediately change the status.
alerts & acoustic settings

machine ready tone

milk quality alert
activate/deactivate a machine ready tone. activate/deactivate a tone each time a button is pressed.

key tones

milk rinsing alert
activate/deactivate a tone that reminds the user to proceed with washing the circuits to prepare milk. activate/deactivate a tone that reminds the user to perform the rinse cycle of the milk circuits (the tone is activated after one minute from the beverage brewing).
Note: The tones are divided in the following way: Long continuous tone indicates a machine malfunction; Brief tone when a button is pressed and to indicate that the machine is ready for use; Intermittent tone to indicate that the machine needs to be cleaned.

DISPLAY MENU

To set the correct brightness of the display colors, press the display button.

display

Adjust the brightness by pressing + or restore default settings save settings back to menu

BEVERAGE SETTINGS

To adjust the general brew parameters of the various beverages containing coffee, press the beverage settings button on the main menu.

espresso espresso macchiato

coffee long coffee

latte macchiato cappuccino
For every single beverage, you can adjust:

temperature

the coffees brew temperature.

coffee settings

prebrewing

strength

the coffees pre-brewing.

normal

the quantity of coffee to be ground and the use of pre-ground coffee.
The current programming status is indicated according to each parameter.
ADJUSTMENT OF THE COFFEE BREW TEMPERATURE
To set the temperature for preparing coffee, press the temperature button and select the desired temperature.
low temperature medium temperature high temperature

coffee temperature

restore default settings save settings back to menu
AROMA ADJUSTMENT FOR COFFEE BREWING
To set the Aroma function, that is to say the quantity of coffee to be ground, and to set the use of pre-ground coffee. You can have your beverage with the quantity of coffee you desire or you can choose to prepare it with decaffeinated coffee by using the preground function.

strenght

light medium strong

coffee strength

PREBREWING ADJUSTMENT (ONLY COFFEE BEVERAGES)
To set the prebrewing function. The coffee is slightly dampened before brewing, bringing out the full aroma of the coffee and extracting the best avor.
normal prebrewing strong prebrewing (longer) deactivate prebrewing

coffee prebrew

ADDITIONAL FUNCTIONS
There are some additional functions of the machine. Pressing the extras button allows you to access the menu and the following message will appear on the display.
In this menu you can: access the menu where some of the most famous recipes in the world are kept.

coffee of the world demo

activate the demo function to show the machines main functions.
view the quantities of every type of product brewed.

beverages counters

go back restore default settings save settings back to menu
COFFEE OF THE WORLD FUNCTION
This function allows the user to prepare coffee according to the most famous recipes in the world.

coffee of the world

In this menu you can: prepare a typical American coffee. prepare a true Italian ristretto. prepare a typical Italian espresso. prepare a typical North European coffee. prepare a typical French/ Swiss coffee. prepare a avorful latte macchiato without the fear of not being able to sleep.
ristretto espresso italiano

american coffee

goodmorning coffee

caf creme goodnight milk

prepare a coffee for a day full of energy.

lock display milk cleaning cycle milk circuit rinsing cycle

coffee cleaning cycle

begin the wash cycle of the brew group.

descaling cycle

perform the descaling cycle.

MILK CIRCUIT RINSE CYCLE

To rinse the machines internal circuits used for preparing milk. This short cycle must be performed after 20 minutes from the last dispensing of a beverage with milk. If this rinse cycle is not performed, the machine comes to a halt and does not allow the dispensing of milk-based beverages. Before performing this function make sure that: 1. a large enough container is positioned under the spout. 2. the milk container has been adequately cleaned of all milk residue and contains fresh drinking water. 3. the water tank contains a sufcient quantity of water. Press the "milk rinsing cycle" button and then "start rinsing" to start the milk circuit rinse cycle.
milk circuit rinsing cycle
Wait for the cycle to nish. The machine will return to the main menu.

MILK CIRCUIT WASH CYCLE

To rinse the machines internal circuits used for preparing milk. This cycle is proposed after 14 days from the rst dispensing of a milk-based beverage. After 14 days, the milk cleaning message starts ashing (see page 13). Perform the wash cycle as described in this section.
Push the milk cleaning button and refer to the instructions below, at step 2. The machine switches to the status described at point 7. If the milk circuit wash cycle is not performed after 14 days, the dispensing of milk-based beverages will be still be possible for only 7 more days. After 7 days, the wash cycle must be performed because the dispensing of milk-based beverages is disabled. (The machine still enables dispensing hot water and coffee). To remind the user of this important operation, the message milk cleaning -3 is shown on the display 3 days before the deadline and is updated on subsequent days.

milk cleaning -3

Before performing this function make sure that: 1. a large enough container is at hand. 2. the milk container has been adequately cleaned of all milk residue. 3. the water tank contains a sufcient quantity of water. THE WASH CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION. USE ONLY AND EXCLUSIVELY THE PROVIDED DETERGENT.

In order to run a descaling cycle before the machine indicates the necessity to do so, press the button "descaling cycle" and then "start descaling" to start the descaling cycle.
descaling cycle start descaling
descaling cycle please wait

descaling.

pause descaling
The machine begins to dispense the descaling solution through the hot water spout. The dispensing occurs at preestablished intervals, in order to allow the solution to be more effective.
insert the water tank with fresh water
rinsing ciclo di risciacquo cycle
When the solution is nished the following message appears on the display:
Remove the water tank and rinse with fresh drinking water to eliminate traces of descaling solution. Then, rell with fresh drinking water and reinsert water tank.
Rinse the machine circuits by pressing "start rinsing".

pause rinsing

The machine performs the rinse cycle. At the end of the rinse cycle you are requested to ll the tank with fresh drinking water. Before relling the tank, reinsert the Aqua Prima lter if desired.
Put a container under the water spout. When the water tank is inserted the machine automatically proceeds to prime the water circuit. If this operation is not successful, consult "manually priming the circuit" (see page 6)

CLOCK SETTINGS

To adjust the current date and time, the timer for stand-by (energy savings) and the times for automatically turning on and turning off the machine. Press the "clock settings" button on the main menu. In this menu you can:

time settings

clock settings
set the parameters for stand-by after the last brew.

energy saving settings

set - the current time - the current date - the view format (24 hour AM/PM) set the intervals for turning the machine on and off (three intervals that can be activated separately).

TIME SETTING

To set all the parameters relating to the clock and calendar. Important: To correctly program the times for turning the machine on and off, press the timer settings button.

time weekday

current time

09:45 (am)

modify the settings related to the current time and the day of the current week.
view the current time setting. view the current day of the week setting. view the current time format setting.

time format

current weekday

thursday

current format
modify the settings relating to viewing the time (in 24 hour or am/pm format).
Current time/day of the week
To set the day of the week and the current time on the machine. Press the "time/weekday" button. In this menu you can:

time weekday 09h (am)

43 min
Adjust the hour by pressing + or Adjust the minutes pressing + or Adjust the day pressing or

weekday

go back save settings

Time format

To set the time view mode. This setting adjusts all clock functions to either am/pm or 24 hour formats. To set the time view mode, press the time format button. The modicatino is immediately applied and in small writing appears am/pm or 24 hour.

AUTOMATIC TIMER SETTINGS

With this function you can turn on (activate) and turn off (energy savings) the machine at the desired times. Remember that the machine manages this function only if it is turned on.
In this menu you can: set the rst interval for turning on

setting 1

on 07:00 am off 09:00 am

setting 2

on 12:00 pm off 14:00 pm
set the second interval for turning on

select a timer setting

setting weekday
choose on what days the intervals are active

setting 3

on 17:00 pm off 19:00 pm
set the third interval for turning on
To correctly program the automatic timer settings, you must: - set the individual intervals for turning on and turning off the machine. - choose on which days to apply these auto on/off intervals. It is recommended to not overlap intervals for turning on the machine.
Setting an interval for turning on the machine

In order to program an interval for turning on the machine, press the button for the interval that you wish to set.

08h (am)

Adjust the hour to turn on by pressing + or -

turn machine on

15 min
save settings back to menu
Adjust the minutes by pressing + or -
To save the adjusted settings and go to the next screen

09h (am)

Adjust the hour to turn off by pressing + or -

turn machine off

To save the adjusted setting
For every day, choose the intervals for turning on
Arrow through the days of the week, and for each day, select the automatic timer intervals you wish to activate.
Interval not active for the selected day
Interval active for the selected day

edit weekday timer

monday
Select the day by pressing or
To save the settings Each day you can select various intervals.

ENERGY SAVING SETTINGS

To set after what duration of time, from the last dispensed beverage, the machine will go into stand-by mode. The default setting is "after 3 hours".

energy saving setting

after 15 min

after 30 min

standby setting

after 3 hours

Select the desired time to activate stand-by.

after 1 hour

When the selected duration of time has passed, the display reads stand-by.
To activate the machine, press start. After having performed the function diagnostics and the heating up phase, the machine is once again ready for use.

SPECIAL

This menu allows you to access special functions present on the machine. Press the "specials" button on the main menu.

factory settings

FACTORY SETTINGS
The function for restoring all the factory settings is contained in this menu. This function is particularly important for restoring the original settings. Press the factory settings button.
do you really want to restore all factory settings? all custom settings will be lost!

attention!

If "yes" is selected, a subsequent conrmation by inverted switch buttons is requested to be sure that you want to perform the reset. ALL THE CUSTOM SETTINGS WILL BE LOST AND CANNOT BE RECOVERED. AFTER RESTORING FACTORY SETTINGS, YOU MUST, IF DESIRED, REPROGRAM ALL THE MACHINE'S FUNCTIONS.
all default settings are restored

Separate the upper part of the cappuccinatore from the lower part.

Remove the cover.

Remove the cap from the lower part.

Wash all components.

Reassemble the components and install the cappuccinatore in the container.

O-RING REPLACEMENT

When both parts of the cappuccinatore move too freely, replace the O-ring with the ones supplied. Quando le due parti del cappuccinatore si muovono troppo liberamente, si deve sostituire l'O-ring con quelli forniti in dotazione.
Remove the O-ring with a sharp object
Insert the new O-ring pressing it delicately.
Assemble the upper and lower part of the cappuccinatore

CLEANING THE BREW GROUP

The Brew Group must be cleaned at least once a week. Lubricate the Brew Group after approximately 500 brewing cycles. The grease for the lubrication of the Brew Group may be purchased by Authorized Service Centres. Wash the brew group with warm water. WARNING! Do not wash the brew group with detergents that can compromise its correct operation. Do not wash in the dishwasher.
Press to open the service door.
Press the PUSH button to remove the brew group.
Wash any coffee residues from the brew group.
Wash the upper lter with running water.
Make sure the group is ready to be put back in. The two references must align.
Make sure the components are in the correct position. The hook shown must be in the correct position; to check its position, rmly press the PUSH button.
The lever on the rear part of the group must be in contact with the group base.
Lubricate the Brew Group guides only with the supplied grease.

Apply the grease evenly.

Insert the washed and dried Brew Group. DO NOT PRESS THE PUSH BUTTON.
Insert the coffee grounds drawer. Close the service door.

GRINDER MAINTENANCE

After approximately 2000 grinding cycles, the grinder needs a slight adjustment to ensure it is running in peak condition. WARNING! This operation should be carried out carefully and by an experienced user. Empty the coffee bean hopper The screw could fall into the grinder; if it happens remove it before restarting the machine. Protect the grinder hole with a cloth to avoid this problem. The snap is signalled by a message on the coffee bean hopper; refer to these messages when this adjustment is performed. Be sure to empty the coffee bean hopper before starting. Note: the screw could fall into the grinder; if that happens, be sure to remove it before continuing the cleaning.
Unscrew the screw that holds the service door closed.
Remove screws and service door.

Adjust until it clicks.

Then reposition the door and attach it with the previously removed screw.

Choose a solid, stationary at surface (no more than 2 of inclination). Do not install the machine in areas where water could be sprayed. Optimal operational temperature: 10C - 40C / 50-104 degrees Fahrenheit maximum humidity: 90%. The machine should be installed in an adequately lit, ventilated, hygienic location and the electric socket should be within easy reach. Do not place on heated surfaces! Install it at least 10 cm / 4" from the walls and cooking surfaces. Do not use in places where the temperature may drop to a level equal to and/or lower than 0C / 32 degrees Fahrenheit. If the machine has been exposed to such conditions notify the customer service center, who will have to carry out a safety check. Do not use the machine near inammable and/or explosive substances. The machine must not be used in an explosive or volatile atmosphere or where there is a high concentration of dust or oily substances suspended in the air. Do not install the machine on top of other appliances.

DANGERS

The appliance must not be used by children and persons who have not been informed of its operation. The appliance is dangerous to children. When left unattended, unplug from the electrical outlet. Keep the coffee machine packaging out of the reach of children. Never direct the jet of hot water and/or steam towards yourself or others. Danger of scalding.
Do not insert objects through the appliances openings. (Danger! Electrical Current!). Do not pull out the plug by yanking on the power cord or touching it with wet hands. Warning. Danger of burning when in contact with hot water, steam and the hot water spout.

FAILURES

Do not use the appliance if a failure has been veried or suspected, for example after being dropped. Any repairs must be performed by an authorized customer service center. Do not use the appliance with a defective power cord. The manufacturer or its customer service center will have to replace the power cable if damaged. (Caution! Electrical Current!) Turn off the appliance before opening the service door. Danger of burns!

CLEANING / DESCALING

Clean the milk circuit only with the recommended detergent powder supplied with the machine. Carefully follow the safety instructions given on the packaging. Clean the coffee circuit only with the recommended detergent tablets supplied with the machine. Carefully follow the safety instructions given on the packaging. Before cleaning the machine, the main switch must be turned to OFF (0), unplugged from the socket and cooled down. Keep the appliance from coming into contact with splashes of water or immersing in water. Do not dry the machines parts in conventional or microwave ovens. The machine and its components must be cleaned and washed after the machine has not been used for a certain period.

REPLACEMENT PARTS

For safety reasons, use only original replacement parts and original accessories.

WASTE DISPOSAL

- The packing materials can be recycled. - Appliance: unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with EU Directive 2002/96/EC. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this product. For more detailed information about recycling of this product, please contact your local city of ce, your household waste disposal service or the shop where you purchased the product.

FIRE SAFETY

In case of re, use Carbon Dioxide extinguishers (CO 2). Do not use water or dry-powder extinguishers.
ADDITIONAL INFORMATION FOR CORRECTLY USING THE AQUA PRIMA FILTER.
Please follow these simple instructions to correctly use the Aqua prima lter: 1. Keep the Aqua prima lter cool and away from sunlight; the room temperature should be between +5C and +40C; 2. Do not use the lter in temperatures over 60C. 3. If the coffee machine is not used for 3 days, we recommend washing the Aqua prima lter; 4 If the coffee machine is not used for more than 20 days, it is advisable to replace the lter. 5. To store an already opened lter, seal it in a nylon bag and keep in the fridge; do not store it in the freezer to avoid damaging the lter properties. 6. Before using the lter, leave it to soak in the water tank for 30 minutes. 7. Once it is taken out of its pack, do not keep the lter in the open air. 8. The lter must be replaced 90 days after opening the packing or after treating 60 litres of drinking water.

Primea: A Masterpiece in Design and Innovation
Saeco, the world leader in automatic espresso machines, offers you an ultra automatic machine producing maximum taste with a bold and impressive statement. Thanks to superior innovations in design and technology, the Primea line prepares espresso with perfect crema, aroma and flavor every time. Prepare every type of coffee to appeal to your senses, such as espresso, cappuccino, latte macchiatto and many more. The Primea line combines exclusive technology with top of the line style and sophistication. The Saeco Advantage: Advanced Display Panels: A large color touch screen with sensitive touch technology or a LCD display screen with click-wheel technology both allow you to easily operate and program your machine. Touch2Cappuccino: Prepare two cappuccinos with just one touch with the built-in Cappuccinatore. Saeco Brewing System (SBS): Make an infinite variety of coffees from one machine with just the twist of a dial. Cup Illumination: A soft light will turn off and on with just the touch of a button to spotlight the drink being brewed.
Features Display Programmable Drink Options Temperature Control Cup Warming Surface Removable Brew Group Automatic Decalcifying Cycle Rapid Steam Insta Steam Frothing Device Touch2Cappuccino Cup Illumination Hot Water Dispenser Saeco Brewing System (SBS) Saeco Aroma System Saeco OptiDose Built-In Grinder Adjustable Grinder Pre-Ground Bypass Doser Adjustable Dispensing Head Adjustable Drip Tray Base Removable Water Tank Aqua Prima Water Filter Bean Hopper Capacity Used Grounds Capacity Boiler Material Machine Housing Unit Size Unit Weight UPC Code Warranty MSRP
Primea Touch Plus color touch screen 6 beverages
Primea Ring LCD display 6 beverages

active

Cappuccinatore (built-in)
7 - 10.5 gr. capacity ceramic disc
motorized sliding wheels 62 oz
10 oz 24 pucks stainless steel ABS plastic 14W x 18D x 15H 33 lbs. 7-08461-80000-year
10 oz 24 pucks stainless steel ABS plastic 14W x 18D x 15H 33 lbs. 7-08461-00002-year
For more information, please contact: Saeco USA 7905 Cochran Road, Suite 100, Glenwillow, OH 44139 Tel: (800) 933-7876 Fax: (440) 542-9173 www.saeco-usa.com
Talea: A New Line of Taste.
From any point of view, the Talea line is a delight to your eyes and your tastebuds. Exclusively designed by BMW Designworks USA, the Talea line features the elegant color combination of silver and titanium. All the traditional tastes of Saeco are included in these new machines with an ergonomic shape and advanced technology. The stunning exterior and high-tech interior make all of the Talea models a pleasant delight.
The Saeco Advantage: Milk Island: The Milk Island prepares a creamy froth in just a few seconds with the simple twist of a dial. User Friendly Interface: Brew the perfect espresso easily at the touch of a button. Rapid Steam: Rapid Steam technology reduces normal waiting time between brewing coffee and steam output to just a few seconds. Cup Warming Surface: Keep your cups and espresso at an optimal temperature while enhancing the full flavors and aromas extracted from the coffee beans.

Talea Touch b/w touch screen 3 beverages
Talea Ring Plus LCD display 3 beverages
Talea Giro indicator lights passive
Milk Island & Pannarello -
Milk Island (optional) & Pannarello -
motorized sliding wheels 57 oz
manual sliding wheels 57 oz
8 oz 14 pucks stainless steel ABS plastic 13W x 16D x 14.5H 21 lbs. 7-08461-00016-year
8 oz 14 pucks stainless steel ABS plastic 13W x 16D x 14.5H 21 lbs. 7-08461-00017-year
8 oz 14 pucks stainless steel ABS plastic 13W x 16D x 14.5H 21 lbs. 7-08461-00018-year

Espresso Italiano Line

Bringing the caf into your own home has never been easier than with the Espresso Italiano. Just add whole beans and water, and instantly you will have a perfectly extracted espresso. With state-of-the-art technology, including a tri-colored digital display screen that helps to easily identify the machines functions, you can make all of your favorite espresso-based drinks, including cappuccino, latte and Americano. Every cup of coffee is freshly ground, dosed, tamped, and brewed with consistent high quality in one cycle, all at the push of a button. The Saeco Advantage: OptiDose: Adjustable 6-9 gram doser to regulate the amount of beans to grind per serving. Conical Burr Grinder: With automatic shut-off, the built-in conical burr grinder is the optimal way to grind beans. Rapid Steam: No waiting between frothing milk with the Pannarello attachment and brewing espresso. Easy Clean System: Fully extractable brew group grinds, doses, tamps, brews and discards used grounds internally.
Espresso Italiano tri-colored digital display 2 -

Pannarello -

6 - 9 gr. capacity conical burr
swivel base 57 oz optional 8 oz 14 pucks stainless steel ABS plastic 13W x 19D x 14.5H 20 lbs. 7-08461-10004-year

Odea: Meet the Future.

The Odea line is characterized by a new touch of purity. Its design is made to please all coffee lovers, who prefer a beautiful, stream-lined style. The parts of the machine are prominently placed to simplify every choice in the coffee making process. The Odea line is built with Saeco quality, and technical innovations that are truly state of the art. Dressed to impress, these models are just hot.
The Saeco Advantage: Steam/Hot Water Wand: The long Pannarello steam wand can froth milk in almost any sized container, and also dispenses hot water. Giro Interface: It is easy to choose the amount and aroma of coffee to brew with just one turn of the dial. Adjustable Drip Tray: The manual drip tray is easily raised or lowered with just a light push. Ceramic Disc Grinder: Provides an even, consistent grind every time.

Odea Giro (Grey) indicator lights passive
Odea Giro (Orange) indicator lights passive
Odea Go indicator lights passive

ceramic disc

manual sliding wheels 50 oz optional 6 oz 14 pucks stainless steel ABS plastic 11.5W x 15D x 14.5H 19 lbs. 7-08461-00022-year
manual sliding wheels 50 oz optional 6 oz 14 pucks stainless steel ABS plastic 11.5W x 15D x 14.5H 19 lbs. 7-08461-00032-year
-. manual sliding wheels 50 oz optional 6 oz 14 pucks stainless steel ABS plastic 11.5W x 15D x 14.5H 19 lbs. 7-08461-00021-year

The Royal Line

Bring the coffeehouse directly into your business or small office with Saecos super automatic Royal line of espresso machines. With all of the programmable features available, the Royals are some of Saecos most impressive machines. The LCD display and programmable push-button technology make it easy for anyone to become a barista. Whole beans are perfectly ground, tamped, brewed and discarded into a used grounds container. Use the steam wand or the built-in Cappuccinatore to easily froth milk directly into your cup.
The Saeco Advantage: LCD Display: Program up to three drink buttons with the easy-to-read interface. Conical Burr Grinder: With automatic shut-off, the built-in conical burr grinder is the optimal way to grind beans. Cappuccinatore Frothing Attachment: Automatically steam and froth milk directly into your cup. Easy Clean System: Fully extractable brew group grinds, doses, tamps, brews and discards used grounds internally.
Royal Coffee Bar LCD display 3 beverages
Royal Professional LCD display 3 beverages
Cappuccinatore & Pannarello -
swivel base 82 oz tank or 3/4 plumbed line optional 10 oz 15 pucks stainless steel metal 15.2W x 15.8D x 19.2H 35 lbs. 7-08461-10055-year
swivel base 82 oz tank optional 10 oz 15 pucks stainless steel metal 15.2W x 15.8D x 19.2H 35 lbs. 7-08461-12110-year

Incanto Line

The Incanto line of super automatic espresso machines feature innovative Saeco technologies including three programmable brew settings and ceramic disc grinders. The Saeco Brewing System makes it easier than ever before to customize and brew espresso at home. Thanks to the Rapid Steam technology, you can easily froth milk to quickly turn your espresso into a cappuccino or latte. The elegant finish and compact footprint make the Incanto line a perfect fit for any kitchen.

The Saeco Advantage: Programmable Brew Settings: Program up to three drink buttons with the easy-to-read interface. Ceramic Disc Grinder: With automatic shut-off, the built-in grinder is safe, quiet and long-lasting. Saeco Brewing System: Make an infinite variety of coffees from one machine with just the twist of a dial. Rapid Steam: Rapid Steam technology reduces the normal waiting time between brewing coffee and steam output to just a few seconds.
Incanto Deluxe LCD display 3 beverages
Incanto Classic indicator lights 2 beverages active
6 - 12 gr. capacity ceramic disc

swivel base 68 oz

10 oz 13 pucks stainless steel metal 12W x 15.5D x 15H 26 lbs. 7-08641-30091-year
10 oz 13 pucks stainless steel metal 12W x 15.5D x 15H 26 lbs. 7-08461-30020-year

Spidem Line

Bringing the caf into your own home has never been easier with the Spidem Villa by Saeco. Just add whole beans and water, and instantly you will have a perfectly extracted espresso. With state-of-the-art technology, you can make all of your favorite espresso-based drinks, including cappuccino, latte, and even regular-strength coffee. Every cup of coffee is freshly ground, dosed, tamped, and brewed with consistent high quality in one cycle, all at the push of a button.
The Saeco Advantage: Coffee Dial Control: Dial display easily adjusts the preferred amount of brewed coffee for each cup. Conical Burr Grinder: With automatic shut-off, the built-in conical burr grinder is the optimal way to grind beans. Pannarello Steam Wand: Quickly steam and froth milk for cappuccinos and lattes perfectly. Easy Clean System: Fully extractable brew group grinds, doses, tamps, brews and discards used grounds internally.
Spidem Villa (Silver) indicator lights -
Spidem Villa (Black) indicator lights -
swivel base 57 oz optional 12 oz 15 pucks stainless steel ABS plastic 15W x 14D x 15.5H 18 lbs. 7-08461-10003-year
swivel base 57 oz optional 12 oz 15 pucks stainless steel ABS plastic 15W x 14D x 15.5H 18 lbs. 7-08461-10004-year

Traditional Line

The traditional line of espresso machines is perfect for those who love the nitty gritty ritual of making an espresso. Each machine is equipped with a pressurized portafilter and an optional pod adapter for the choice of using ground coffee or pre-packed ESE pods for brewing. The Pannarello steam wand froths milk consistently for the perfect cappuccino or latte every time.

The Saeco Advantage: P ressurized Portafilter: The patented filter holder pressurizes the brewing chamber, ensuring a great extraction of espresso. Pannarello Steam Wand: Used to manually froth milk for cappuccinos and lattes. Also produces hot water for tea. ESE Pod Adapter Capability: A pod adapter and special filter basket enable the portafilter to handle single serve prepackaged shots (pods). Cup Warming Surface: Comfortably holds espresso cups and is heated by the residual heat of the boiler.
Features Pressurized Portafilter Pannarello Steam Wand Plug-In Cappuccinatore Pod Adaptable Filter Holder Cup Warming Surface Hot Water Dispenser Dual Spout Dispensing Head Removable Water Tank Water Tank Capacity Boiler Pump Pressure Machine Housing Unit Size Unit Weight UPC Code Warranty MSRP

Magic Cappuccino Plus

included

optional

passive
68 oz stainless steel 15 bar ABS plastic 9.5W x 11D x 14H 13.5 lbs. 7-08461-00033-year
85 oz stainless steel 15 bar metal 8W x 10D x 11.75H 14 lbs. 7-08461-00035-4 (SS) 7-08461-00034-7 (Blk) 1 year

450-$400

Nina Line
The new Nina series of espresso machines completes the BMW-designed Saeco line with sleek lines, compact construction and a modern color palette. These traditional machines are equipped with a stainless steel boiler, a pressurized portafilter, and an optional pod adapter to choose between ground coffee or pre-packed ESE coffee pods. The Pannarello steam wand or Cappuccinatore froths milk consistently for the perfect cappuccino or latte every time. The Saeco Advantage: P ressurized Portafilter: The patented filter holder pressurizes the brewing chamber, ensuring a great extraction of espresso. Pannarello Steam Wand: Used to manually froth milk for cappuccinos and lattes. Also produces hot water for tea. ESE Pod Adapter Capability: A pod adapter and special filter basket enable the portafilter to handle single serve prepackaged shots (pods). Cup Warming Surface: Comfortably holds espresso cups and is heated by the residual heat of the boiler.
Features Display Pressurized Portafilter Pannarello Steam Wand Plug-In Cappuccinatore Pod Adaptable Filter Holder Cup Warming Surface Hot Water Dispenser Dual Spout Dispensing Head Removable Water Tank Water Tank Capacity Boiler Pump Pressure Machine Housing Unit Size Unit Weight UPC Code Warranty MSRP

Nina Bar touch interface

Nina Cappuccino coffee dial

Nina coffee dial

50 oz stainless steel 15 bar metal 11W x 12D x 14H 9 lbs. 7-08461-00038-year
50 oz stainless steel 15 bar ABS plastic 11W x 12D x 14H 9 lbs. 7-08461-00040-year
50 oz stainless steel 15 bar metal 11W x 12D x 14H 9 lbs. 7-08461-00041-year

Drip Coffeemakers

Saeco, the leading manufacturer of espresso machines, is taking its passion for coffee in new directions. These urns and drip coffee products join the industry leaders highly successful product lines that include automatic and traditional home espresso machines, professional and foodservice equipment, vending machines and coffee accessories. Renaissance Coffee Urn: While bringing the knowledge of proper brewing techniques to larger volume customers and events, the Renaissance Coffee Urn delivers the freshest cups of coffee to home entertaining, catering and restaurant service. Renaissance Portable Coffee Urn: Freshly brewed coffee is made even more accessible with the Renaissance Portable Coffee Urn. Holding 25 cups of coffee, this urn is perfect for family gatherings, parties or meetings. The large, heat resistant handle makes it easy to transport. Renaissance Glass: The Renaissance Glass sets out to change the way coffee lovers think of the drip coffeemaker. Combining European styling with the latest innovations, this machine makes brewing a carafe of hot, flavorful coffee easier than ever.
Renaissance Urn Large 60 Cup Capacity Heat Resistant Handle Built-In Cord Storage Stainless Steel Housing Water Indicator Tube Digital Display Control Panel Detachable Power Cord Two Way Dripless Spout Unit Size: 12.5W x 11D x 20H Unit Weight: 9.5 lbs. UPC Code: 7-08461-00098-9 Warranty: 1 year MSRP Price: $179
Renaissance Portable Urn 25 Cup Capacity Large Heat Resistant Handle Stainless Steel Housing Water Indicator Tube Digital Display Control Panel Detachable Power Cord Newly Designed Dripless Spout Unit Size: 8.75W x 11.5D x 13.5H Warranty: 1 year Unit Weight: 9.5 lbs. MSRP Price: $149 UPC Code: 7-08461-11008-4
Renaissance Glass Top Loading Filter Basket 55 oz. Top Filling Water Tank Pause n Serve Glass Carafe and Hot Plate with Keep Warm Function Built-In Cord Storage Programmable LED Control Panel Automatic Shut-Off Unit Size: 8.25W x 12.25D x 14.5H Warranty: 1 year Unit Weight: 6 lbs. MSRP Price: $149 UPC Code: 7-08461-10011-5