s re sp

ec ot s

Sa le s& Se

ce rvi
Operation and maintenance manual
Before using the machine, please read the attached operating instructions. Carefully read the safety rules

Mode d'emploi

Veuillez lire attentivement le mode d'emploi (notamment les consignes de scurit) avant d'utiliser l'appareil.

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed to reduce the risk of fire, electric shock, and/or injury to persons, including the following: 1 Read all instructions and information in this instruction book and any other literature included in this carton referring to this product before operating or using this appliance. 2 Do not touch hot surfaces. Use handles or knobs. 3 To protect against fire, electric shock and personal injury do not immerse cord, plugs or appliance in water or other liquid. 4 Close supervision is necessary when any appliance is used by or near children. 5 Unplug from outlet when not in use and before cleaning. Allow to cool before putting on or taking off parts, and before cleaning the appliance. 6 Do not operate any appliance with a damaged cord or plug or after the appliance malfunctions or has been damaged in any way. Return appliance to the nearest authorized service centre for examination, repair or adjustment. 7 The use of accessory attachments not recommended by the appliance manufacturer may result in fire, electric shock or personal injury. 8 Do not use outdoors. 9 Do not let cord hang over edge of table or counter, or touch hot surfaces. 10 Do not place on or near a hot gas or electric burner, or in a heated oven. 11 Always turn appliance OFF, then plug cord into the wall outlet. To disconnect, turn switch to OFF, then remove plug from wall outlet. 12 Do not use appliance for other than intended household use. 13 Use extreme caution when using hot steam.

SAVE THESE INSTRUCTIONS

This appliance is for household use only. Any servicing, other than cleaning and user maintenance, should be performed by an authorized service centre. Do not immerse machine in water. To reduce the risk of fire or electric shock, do not disassemble the machine. There are no user serviceable parts inside the machine serviceable by the user. Repair should be done by authorized service personnel only. 1 Check voltage to be sure that the voltage indicated on the nameplate corresponds with your voltage. 2 Never use warm or hot water to fill the water tank. Use cold water only. 3 Keep your hands and the cord away from hot parts of the appliance during operation. 4 Never clean with scrubbing powders or harsh cleaners. Simply use a soft cloth dampened with water. 5 For optimal taste of your coffee, use purified or bottled water. Periodic descaling is still recommended every 2-3 months.

CAUTION

A A short power-supply cord is provided to reduce risks of tangling or tripping over a longer cord. B Longer extension cords are available and may be used if care is exercised in their use. C If a long extension cord is used: 1 the marked electrical rating of the extension cord should be at least as great as the electrical rating of the appliance. 2 if the appliance is of the grounded type, the extension cord should be a grounding type 3 the cord should not hang from the table to avoid the risk of tangling or tripping.
INSTRUCTIONS FOR THE POWER SUPPLY CORD

CONTENTS

GENERAL INFORMATION.... 3 APPLIANCE..... 4

ACCESSORIES..... 4

INSTALLATION.... 5
STARTING THE MACHINE..... 5 SETTING THE LANGUAGE..... 6 AQUA PRIMA WATER FILTER.... 7

DISPLAY..... 8

(OPTI-DOSE) INDICATES THE GROUND COFFEE QUANTITY.... 8

ADJUSTMENTS..... 9

COFFEE INTENSITY.... 9 ADJUSTING THE HEIGHT OF THE DRIP TRAY..... 9 COFFEE GRINDER ADJUSTMENT..... 9
PRODUCT DISPENSING.... 10
ESPRESSO / COFFEE / LONG COFFEE..... 10 DISPENSING BEVERAGES WITH PRE-GROUND COFFEE... 11 HOT WATER DISPENSING..... 12 STEAM DISPENSING..... 13 CAPPUCCINO...... 14 MILK ISLAND (OPTIONAL).... 15
BEVERAGE PROGRAMMING... 16

BEVERAGE PROGRAMMING MENU.... 16 ESPRESSO / COFFEE / LONG COFFEE PROGRAMMING... 17
PROGRAMMING THE MACHINE... 18
<LANGUAGE & DISPLAY> LANGUAGE MENU.... 19 <LANGUAGE & DISPLAY> CONTRAST MENU.... 19 <ALERTS AND ACOUSTIC SETTINGS> READY MACHINE MENU... 20 <ALERTS AND ACOUSTIC SETTINGS> KEY TONE MENU... 20 CUP-WARMING SURFACE MENU..... 20 <WATER SETTINGS> RINSE.... 21 <WATER SETTINGS> WATER FILTER MENU.... 21 <WATER SETTINGS> WATER HARDNESS MENU.... 22

BEVERAGE SETTINGS.... 23

PREBREWING ADJUSTMENT..... 23 COFFEE TEMPERATURE ADJUSTMENT.... 24 OPTI-DOSE ADJUSTMENT FOR COFFEE BREWING.... 24 WATER QUANTITY ADJUSTMENT FOR COFFEE BREWING... 24
TIME/DATE SETTINGS..... 25
SET CLOCK..... 25 DATE SETTINGS..... 26 STAND-BY SETTINGS..... 27 MACHINE ON/OFF.... 28
MAINTENANCE SETTINGS.... 30
<PRODUCT COUNT.> TOTAL COUNT. MENU.... 30 <PRODUCT COUNT.> PARTIAL COUNT. MENU.... 30 CLEANING CYCLE MENU.... 31 BOILER DESCALING CYCLE MENU.... 32 LOCK DISPLAY MENU..... 34

SPECIAL..... 35

FACTORY SETTINGS..... 35
CLEANING AND MAINTENANCE.... 36
GENERAL MACHINE CLEANING..... 36 CLEANING THE BREW GROUP..... 37
ERROR CODES.... 38 TECHNICAL DATA..... 39 SAFETY RULES.... 40

GENERAL INFORMATION

The coffee machine is suitable for preparing espresso coffee using coffee beans, and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use only, and is not suitable for heavy or professional use. Warning: no liability is assumed for any damage caused by: incorrect use not in accordance with the intended uses; repairs not carried out by authorized customer service centres; tampering with the power cable; tampering with any part of the machine; the use of non-original spare parts and accessories; failure to descale the machine or use at temperatures below 0C (32F)
IN THESE CASES, THE WARRANTY IS NOT VALID.
THE WARNING TRIANGLE INDICATES ALL IMPORTANT INSTRUCTIONS FOR THE USERS SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES!

The machine is now ready for use.
Set the clock and the calendar of the machine as shown on page 25.

AQUA PRIMA WATER FILTER

To improve the quality of the water you use, and extend the life of your machine at the same time, it is must be replaced.
Remove the Aqua Prima water date of the current month. Press down until it clicks into place.
Fill the tank with fresh drinking the full tank for 30 minutes for a correct initialization.

1.2.4 water settings

rinse on water hardness 3/4 39
Access programming (see page 18 and 19). Press water settings.

on off

Have you replaced the old water

reload water

Press the
Turn the knob until the position is reached. Water dispensing begins. ).
Fill the water tank if necessary.

DISPLAY

It is possible to change the type of display and choose between icon format and text format ICON FORMAT

TEXT FORMAT

espresso

coffee

medium

long coffee

strong
Go to the text format menu

Enter the clock menu

Enter the programming menu
Go to the icon format menu
To get the desired coffee, press the corresponding symbol on the display. The machine automatically performs all the necessary operations. Press the icon twice to make 2 cups. press twice
(OPTI-DOSE) INDICATES THE GROUND COFFEE QUANTITY
The colour intensity of the icon indicates the quantity of coffee to be ground for preparing the product. The greater the quantity of coffee ground, the stronger the coffee dispensed will be.
When the machine is programmed to use pre-ground coffee or when a product is customized, the icon is displayed in a different way and/or accompanied by an asterisk (see the paragraphs about programming beverages).

pre-ground

customization

ADJUSTMENTS

COFFEE INTENSITY
The SBS system has been carefully designed to give your coffee the intense taste you desire. Simply turn the dial and you will notice that the coffee goes from mild intensity to strong intensity. MEDIUM COFFEE

SBS SAECO BREWING SYSTEM

SBS adjusts the intensity of the brewed coffee. The coffee may even be adjusted while brewing. This adjustment has an immediate effect on the selected type of brewing.

MILD COFFEE

STRONG COFFEE

ADJUSTING THE HEIGHT OF THE DRIP TRAY
Adjust the drip tray before dispensing any beverages so as to be able to use any kind of cup. To raise the drip tray, press lightly on the lower part of the button. To lower the drip tray, press lightly on the upper part of the button. When the desired height is reached, release the button. is necessary to empty the tray.
COFFEE GRINDER ADJUSTMENT
The machine lets you make slight adjustments to the coffee grinder to adapt it to the kind of coffee used. The adjustment must be performed by pressing the pin located inside the coffee hopper. This must be turned by means of the supplied key only. Turn the pin one notch at a time and brew 2-3 cups of coffee; the grinder adjustment can only be noticed in this way. The references located inside the container indicate the grind setting. FINE GRIND MEDIUM GRIND COARSE GRIND

PRODUCT DISPENSING

COFFEE BREWING CAN BE STOPPED AT ANY TIME BY PRESSING STOP COFFEE AGAIN. THE STEAM SPOUT MAY REACH HIGH TEMPERATURES: DANGER OF SCALDING. DO NOT TOUCH IT WITH BARE HANDS.
grind the second coffee dose. Coffee dispensing is then restarted and completed.
ESPRESSO / COFFEE / LONG COFFEE
This procedure shows how to dispense an espresso. To dispense another type of coffee, press the appropriate
Position 1-2 cup(s) to dispense an espresso
Position 1-2 cup(s) to dispense a coffee or a long coffee
Choose the product and press the corresponding icon on the display: once for 1 cup and twice for 2 cups.
stop coffee show text 8:30 am 15/06/06 go to menu
The machine begins grinding the set quantity of coffee.
The machine begins dispensing the selected beverage.
The machine ends dispensing automatically on the basis of the quantity determined by the manufacturer. It is possible to customize this quantity. See page 16.
DISPENSING BEVERAGES WITH PRE-GROUND COFFEE
The machine allows you to use pre-ground and decaffeinated coffee.Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean hopper. Only use coffee ground for espresso machines and never coffee beans or instant coffee. (see the Beverage programming section on page 16)
WARNING: PUT PRE-GROUND COFFEE INTO THE COMPARTMENT ONLY WHEN YOU WISH TO DISPENSE THIS TYPE OF PRODUCT. INSERT ONLY ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE DISPENSED AT THE SAME TIME.
The preparation of a coffee with pre-ground coffee is shown in the example given below. The customized choice of using pre-ground coffee is shown on the display with an asterisk next to the chosen beverage.
coffee add pre-ground coffee! stop coffee

start!

Place 1 cup to brew one coffee.
Press the appropriate key. The display will show:
A message reminds the user to pour pre-ground coffee into the appropriate compartment.

stop coffee

Pour pre-ground coffee in the appropriate compartment using the measuring scoop provided.

Select steam dispensing (see point 2 and 3 on page 13).
Place the cup beneath the steam spout.
Froth the milk: move the cup during heating.
Place the cup beneath the spout.
Press the key once to brew coffee.
After dispensing, clean the steam spout as described on page 36. To dispense 2 cappuccinos: froth two cups of milk by following point 1 to 6;

MILK ISLAND (OPTIONAL)

This device, which may be purchased separately, enables you to easily and comfortably prepare delicious cappuccinos. Warning: before using the Milk Island, read the manual and all precautions carefully for correct use. Important note: the quantity of milk in the carafe must never be below the MIN minimum level nor exceed the MAX maximum level. Thoroughly clean all the Milk Island components after use. To guarantee best results when preparing cappuccino, we recommend using cold (0-8C / 32-45F), partially skimmed milk. 3
Fill the milk carafe with the quantity of milk desired (between the MIN and MAX levels indicated). 4
Place the milk carafe onto the base of the Milk Island. Check that the light on the base is green. The machine will stop automatically after dispensing steam continuously for 2 minutes. To dispense more steam turn the knob to the ( ) position and then back to the position.
Turn the knob to the position. 5
Wait for the milk to be frothed.
When the desired emulsion has been reached, turn the knob until it is in the rest position ( ). 7 8
Remove the carafe using the handle.
Gently swirl the carafe and pour the milk into the cup.
Position the cup with frothed milk under the dispensing head. Dispense coffee into the cup.

BEVERAGE PROGRAMMING

BEVERAGE PROGRAMMING MENU
Every beverage can be programmed according to your individual tastes. This customization is shown on the display by adding an asterisk.
When a product has been customized, it is possible to dispense only that type of coffee. To modify the quantity of coffee, you must do a new customization or reset the customization.
To program the desired beverage:

<LANGUAGE & DISPLAY> LANGUAGE MENU
To change the display language of the messages. Press language & display and language.

language

language & display

English

italiano (ch)

deutsch

This function was described at the beginning of the manual. This setting is of fundamental importance for correctly adjusting the parameters of the machine according to the country where the machine is used. To display the other available languages.
<LANGUAGE & DISPLAY> CONTRAST MENU
To set the correct contrast of the display. Press language & display and contrast.
lingua & display contrast 10 / 15

In this menu you can:

1.2.1.2. contrast
Adjust the contrast by pressing + or

10 / 15

<ALERTS AND ACOUSTIC SETTINGS> READY MACHINE MENU
This function activates/deactivates a tone every time the machine is ready. Press alerts and acoustic settings and machine ready.
alerts and acoustic settings

machine ready

1.2.2.1. machine ready

activate the tone

deactivate the tone
<ALERTS AND ACOUSTIC SETTINGS> KEY TONE MENU
This function activates/deactivates a tone every time a key is pressed. Press alerts and acoustic settings and key tone.

key tone

1.2.2.2. key tone

activate the key tone

deactivate the key tone

CUP-WARMING SURFACE MENU

To set the operation of the cup-warming surface located on the upper part of the machine. Press cup-warming surface In this menu you can:

cup-warming surface

1.2.3. cup-warming surface
keep the cup-warming surface always on.

always on

always off
keep the cup-warming surface always off.
keep the cup-warming surface off when the machine is in stand-by mode

off while in stand-by

<WATER SETTINGS> RINSE
To clean the internal circuits in order to guarantee that the beverages are only made with fresh water. The function is enabled as default by the manufacturer. Note: this rinse cycle is performed every time the machine is turned on after the warming phase. Press water settings and rinse.

water settings rinse on

1.2.4.1. rinse

activate the rinse cycle

deactivate the rinse cycle
<WATER SETTINGS> WATER FILTER MENU
To activate/deactivate the warning to replace the Aqua Prima water filter. The machine informs the user when the Aqua Prima water filter needs to be replaced. Press water settings and water filter. In this menu you can:

temperature medium

Medium temperature
OPTI-DOSE ADJUSTMENT FOR COFFEE BREWING
To set the coffee quantity to be ground and to set the use of pre-ground coffee. You can taste your beverage with the quantity of coffee you desire or you may choose to prepare it with decaffeinated coffee using the pre-ground function. Press coffee aroma. In this menu you can select: 1.1.2.3. coffee aroma mild aroma

mild medium

aroma medium

medium aroma

strong aroma

pre-ground coffee

the use of pre-ground coffee
WATER QUANTITY ADJUSTMENT FOR COFFEE BREWING
To set the water quantity to be used for preparing coffee. Press coffee volume. In this menu you can select: 1.1.2.4. coffee volume

coffee volume

Adjust the quantity by pressing + or Adjust the quantity according to the cups you whish to use.

TIME/DATE SETTINGS

To set the current time, the stand-by timer and the energy saving function. Press time/date settings from the main menu. In this menu you can:

1.3 time/date settings

set the current time set the parameters for stand-by after the last dispensing

set clock

date settings
set the date set the intervals (three intervals that can be activated separately) for turning the machine on and off (energy savings).

stand-by settings

machine on/off

SET CLOCK

To set all the parameters concerning the clock. Important to correctly program the times for turning the machine on and off! Press set clock.

1.3.1. set clock

set the current time

current time 08:00

time format 24 hr
set the time view mode (in 24 hour or am/pm format).

Current time

To set the current time on the machine. Press current time.

current time 08:00 08

1.3.1.1. current time
Adjust the hour by pressing + or Adjust the minutes by pressing + or

00 min

Time format
To set the time view mode. The modification of this setting adjusts all the parameters that require viewing/setting the time. Press time format.

1.3.1.2. time format

International format view mode
American format view mode

DATE SETTINGS

To set all the parameters concerning the calendar. Important to correctly program the times for turning the machine on and off. Press date settings.

1.3.2. date settings

current date date format dd/mm/yy

set the current date

15/06/06

set the date view mode.

Current date
To set the current date on the machine. Press current date.

current date 15/06/06

Adjust the hour for turning on by pressing + or Adjust the minutes by pressing + or
After having set the turn on time, adjust the turn off time by pressing the key.

09 h turning off 00 min

Adjust the hour for turning off by pressing + or Adjust the minutes by pressing + or
Press the key to return to the turn on times. Note: to save the settings press one of the keys: o
For each day, choose the intervals for turning on
Scroll the days of the week and, for each day, select the interval/s you wish to activate.

week day settings

Interval active for the selected day
1.3.4.4. week day settings
interval 1 on 07:30 off 09:00
interval 2 on 11:00 off 13:00
Interval NOT active for the selected day
interval 3 on 17:00 off 19:00

Monday

The selected day of the week is displayed.
To select the day of the week You can select various intervals for each day. Note: to save the settings press one of the keys: o

MAINTENANCE

MAINTENANCE SETTINGS
To clean/maintain all the machines internal circuits. Press maintenance settings on the main menu. In this menu you can:

1.4 maintenance settings

display the products dispensed by the machine perform the descaling cycle (the machine indicates how many litres can be dispensed before descaling).
product counters boiler descaling cycle 58

cleaning cycle

perform the cleaning cycle of the Brew Group temporarily lock the touch screen (e.g. to clean the display)

lock display

<PRODUCT COUNT.> TOTAL COUNT. MENU

1.4.1.1. total count.

espresso 6 long coffee 4 coffee 10

product counters

total count. 20
display how many espresso coffees have been brewed display how many long coffees have been brewed
display how many coffees have been brewed
<PRODUCT COUNT.> PARTIAL COUNT. MENU
This function shows how many products have been prepared for every single type of coffee since last reset. Press product counters and partial count.
product counters partial count. 10

1.4.1.2. partial count.

espresso 3 long coffee 2 coffee 5 reset
display how many coffees have been brewed reset all the partial counters

CLEANING CYCLE MENU

To clean the machines internal circuits used for brewing coffee. To wash the Brew Group, simply clean with water as shown on page 37. This cleaning completes the maintenance of the Brew Group. We recommend using saeco tablets, which can be purchased separately at your local dealer. Note: before performing this function make sure that: 1. a large enough container is positioned under the spout; 2. the appropriate tablet for washing the Brew Group has been inserted; 3. Fill the water tank. THE CLEANING CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION. Press cleaning cycle

1.4.2. cleaning cycle

Have you inserted the cleaning tablet
Make sure that the tablet has been inserted as shown. Press yes.
(approximately 8 minutes). The machine will return to the main menu.
BOILER DESCALING CYCLE MENU
To perform the automatic descaling cycle. Descaling is necessary every 3-4 months or when the machine indicates it. The machine must be turned on and will automatically manage the distribution of the descaler. A PERSON MUST BE PRESENT DURING THE OPERATION. WARNING! NEVER USE VINEGAR AS A DESCALER.
Saeco descaler is recommended; however, you can use any non-toxic and/or non-harmful descaling product for coffee machines, commonly available in the shops. The used solution is to be disposed of according to the manufacturers instructions and/or regulations in force in the country of use.
Note: before beginning the descaling cycle make sure that: 1. a large enough container is positioned under the water spout; 2. THE AQUA PRIMA WATER FILTER HAS BEEN REMOVED. Press boiler descaling cycle

boiler descaling cycle

Descaling is carried out at a controlled temperature. If the machine is cold, you must wait until it has reached the right temperature; otherwise you must cool the boiler as follows:
1.4.3. boiler descaling cycle
Do you wish to perform the

Press yes to start.

Place a large enough container beneath the hot water spout.
Turn the knob to the reference.

descaling solution

When the following message appears, the heater is at the right temperature
Pour the descaling solution into the tank. Insert the tank into the machine.

button to start.

following message appears on the display:
The machine begins to dispense the descaling solution through the hot water spout. The dispensing occurs at predetermined intervals, in order to allow the solution to be more effective.
The intervals are displayed in such a way as to check the state of progress of the process.
Remove the water tank, rinse with fresh drinking water to eliminate traces of the descaling drinking water.
Insert the tank with fresh drinking water.

boiler cleaning cycle

Rinse the machines circuits by pressing the key.

The machine performs the rinse cycle. During the rinse cycle, the machine may require the water tank
following screen appears.Remove the tank, install the Aqua Prima with fresh drinking water.
Turn the knob until it is in the rest position ( ).
When descaling is complete, return to the main menu to dispense beverages.

LOCK DISPLAY MENU

To clean the display. The touch screen display may be cleaned with a dampened cloth or with appropriate detergents for cleaning displays sold on the market. Solvents, alcohol, harsh detergents and/or sharp objects that may damage the display must not be used.

Press lock display

1.4.4. lock display

display locked unlock

To reactivate the display, press unlock on the lower right-hand corner and then (within two seconds) unlock in the upper left-hand corner (this message appears only after having pressed the previous key).

unlock

display locked

SPECIAL

This menu allows you to access special functions present on the machine. Press special settings on the main menu.

2.1. special settings

go to menu special settings factory settings

FACTORY SETTINGS

The function for restoring all the factory settings is contained in this menu. Press factory settings.

factory settings

2.1.1. factory settings
All your personal settings will be canceled.
If yes is selected, a subsequent conrmation by inverted keys is requested.
ALL THE CUSTOM SETTINGS WILL BE LOST AND CANNOT BE RECOVERED. AFTER RESTORING FACTORY SETTINGS, YOU MUST, IF DESIRED, REPROGRAM ALL THE MACHINE FUNCTIONS.

please wait.

By selecting yes the settings are restored.
All the parameters are restored.

CLEANING AND MAINTENANCE

GENERAL MACHINE CLEANING
The cleaning described below must be performed once a week. Note: if water remains in the tank for several days, do not use it. WARNING! Never immerse the machine in water. If you remove grounds with the machine off or when not signaled on the display, the count of the grounds emptied into the drawer is not reset. For this reason the machine might display the empty coffee grounds drawer message even after preparing just a few coffees.
Switch off the machine and unplug it.
Clean the tank and the cover.
Remove the drip tray, empty and wash it.
Remove the grounds drawer.

Empty and clean it.

With the brush, clean the preground coffee compartment.

Remove the outer sleeve of the steam spout; then re-insert it.
Remove and wash the steam spout support; then re-insert it.
Clean the display with a dry cloth.

CLEANING THE BREW GROUP.

The Brew Group must be cleaned at least once a week. Wash the Brew Group with warm water. WARNING! Do not wash the Brew Group with detergents that can compromise its correct operation. Do not wash in the dishwasher.
Open the service door and remove the dregs drawer.
Press the PUSH button to remove the Brew Group.

and dry.

Make sure the Brew Group is in rest position; the two references must match.
Make sure the components are in the correct position. The hook shown must be in the correct position; to PUSH button.
The lever on the rear part of the group must be in contact with the group base.
Insert the washed and dried Brew Group. DO NOT PRESS THE PUSH BUTTON.

Insert the dregs drawer.

Close the service door.

ERROR CODES

HOW TO REMOVE THE MESSAGE Close the coffee bean hopper lid to be able to make a beverage. Fill the coffee bean hopper with coffee beans. Insert the Brew Group in its seat. Insert the coffee grounds drawer. Remove the coffee grounds drawer and empty the grounds into an appropriate container. Note: the coffee grounds drawer must be emptied only when the machine requires it and when the machine is turned on. If you empty the drawer with the machine turned off it will not record the emptying operation. Close the service door to be able to make the machine functional. water.
GUIDE MESSAGE THAT APPEARS close coffee bean lid add coffee beans insert brew group insert coffee grounds drawer empty coffee grounds drawer

door open

empty drip tray
Open the side door and empty the drip tray located under the Brew Group. following cases: 1. 60 litres of water have been dispensed; 2. 90 days have passed since its installation; 3. 20 days have passed and the machine has not been used. Note: this message appears only when inserted has
carafe removed milk island removed
The steam knob has been turned to the position and either the Milk Island has not been installed or the carafe is not positioned correctly. Install the Milk Island or position the carafe correctly. Otherwise, turn the knob until it is in the rest position ( ). A descaling cycle must be performed on the machines internal circuits. Press start
descale energy saving Stand-by

TECHNICAL DATA

Nominal voltage Power rating Power supply Shell material Size (w x h x d) Weight Cable length Control panel Water tank Coffee bean hopper capacity Pump pressure Boiler Coffee grinder Quantity of ground coffee Dregs drawer capacity Safety devices 14 Boiler pressure safety valve Double safety thermostat. 250 grams - 8.9 oz / coffee beans 15 bar Stainless steel With ceramic burrs Front (TOUCH-SCREEN) 9 Kg - 19.8 lbs See label on the appliance See label on the appliance See label on the appliance ABS - Thermoplastic

FIRE SAFETY

Do not use water or dry-powder extinguishers.

BEVERAGE PROGRAMMING... 16
1. PROGRAMMING FOR SELF-LEARNING.... 16 2. PROGRAMMING FROM THE BEVERAGE SETTINGS MENU... 16
PROGRAMMING THE MACHINE... 18

MACHINE SETTINGS..... 19

LANGUAGE MENU..... 19 WATER HARDNESS MENU.... 20 ACOUSTIC ALARM MENU..... 20 FILTER ALARM MENU..... 21 RINSE MENU..... 21 CUP WARMING SURFACE MENU.... 21 CLOCK SETTING MENU..... 22

MAINTENANCE.... 25

WATER FILTER MENU..... 25 DESCALING MENU..... 27 BREW GROUP WASHING..... 30
PROGRAMMING THE MACHINE... 31
ENERGY SAVING..... 31 TURN OFF DELAY.... 31 TIMER SETTING
..... 31 MONDAY TIMER SETTING.... 32

SPECIAL FUNCTIONS.... 33

RESTORE SETTINGS..... 33
CLEANING AND MAINTENANCE.... 34
GENERAL MACHINE CLEANING..... 34 CLEANING THE BREW GROUP..... 35
ERROR CODES.... 36 TROUBLESHOOTING.... 37 SAFETY RULES.... 38 TECHNICAL DATA..... 40

GENERAL INFORMATION

The coffee machine is suitable for preparing espresso coffee using coffee beans, and it is equipped with a device to dispense steam and hot water. The machine is designed for domestic use only, and is not suitable for heavy or professional use. Warning: no liability is assumed for any damage caused by: incorrect use not in accordance with the intended uses; repairs not carried out by authorized customer service centres; tampering with the power cable; tampering with any part of the machine; the use of non-original spare parts and accessories; failure to descale the machine or use at temperatures below 0C (32F)
IN THESE CASES, THE WARRANTY IS NOT VALID.
THE WARNING TRIANGLE INDICATES ALL IMPORTANT INSTRUCTIONS FOR THE USERS SAFETY. PLEASE FOLLOW THESE INSTRUCTIONS CAREFULLY TO PREVENT SERIOUS INJURIES!
HOW TO USE THESE OPERATING INSTRUCTIONS.
Keep these operating instructions in a safe place and make them available to anyone else who may use the coffee machine. For further information or in case of problems, please refer to any authorized service centre.

APPLIANCE

Coffee bean hopper Coffee bean hopper cover Cup warming surface Control panel SBS knob Dispensing head Service door Dregs drawer Compartment for preground coffee Power button
Hot water / steam knob Button for raising/lowering the drip tray
Hot water / steam spout Water tank Brew Group Milk Island connection Drip tray

Socket for power cable

ACCESSORIES

Aqua Prima

Ground coffee measuring scoop

Water hardness tester

Cleaning brush

Grinder adjustment key

Power cable

INSTALLATION

STARTING THE MACHINE
Make sure that the main power button is not pressed in the ON position.
Remove the coffee bean hopper cover. Fill the hopper with coffee beans.

Close the cover pushing it down completely.
Remove the water tank. We recommend installing the Aqua
Fill the tank with fresh drinking water. Do not exceed the max level indicated on the water tank. the machine.
Attach the female end of the power cord to the machine. Insert the male end into the power outlet (see data tag).
Place a container beneath the hot water spout.
The machine automatically primes the water circuit. The machine is now ready for use.
Water may not be dispensed into the container. This should not be considered a malfunction.
Press the main power button to the ON position.
TO ASSESS WATER HARDNESS, SEE WATER HARDNESS MENU ON PAGE 20.

SETTING THE LANGUAGE

These settings allow you to regulate the machines parameters to dispense coffee according to the typical parameters of the country where it is used. For this reason, the languages are also differentiated by location.

1 beverage settings

2 machine settings
Select machine settings by navigating Press selection.

2.1 language English

Press selection.
Select by navigating the click
When the desired language is displayed, press.
The machine now displays the messages in the language selected.
Press until the following message is displayed.
Wait until the machine completes the heating stage. When the right temperature is reached, the machine performs a rinse cycle in the internal circuits. A small quantity of water is dispensed. Wait for this cycle to be completed automatically. The screen for product dispensing appears on the display. See page 8.

AQUA PRIMA WATER FILTER

To improve the quality of the water you use, and guarantee longer machine life at the same time, it is
Remove the Aqua Prima water date of the current month. until it clicks into place.
Fill the tank with fresh drinking tank for 30 minutes for correct initialization.

3 maintenance

1. 2. Place a container beneath the steam/hot water spout. Press. Select maintenance and press the button.

3.1 water filter

3.1.3 activate filter execute now
1. 2. Press again. position. Turn the knob to the Water dispensing begins.

button.

exit message is displayed. Then press
). Press. The machine is now ready for use.

ESPRESSO / COFFEE / LONG COFFEE
This procedure shows how to dispense an espresso. To dispense another type of coffee, select it by navigating
Position 1 - 2 cup(s) to dispense an espresso
Position 1 - 2 cup(s) to dispense a regular coffee or a long coffee
Select the desired beverages by navigating the click wheel with
If desired, select the quantity of coffee to be ground by pressing the button one or more times.
Press the button: once for 1 cup and twice for 2 cups. The machine begins dispensing the selected beverage.
The machine ends dispensing automatically on the basis of the quantity determined by the manufacturer. It is possible to customize this quantity (see page 16).
DISPENSING BEVERAGES WITH GROUND COFFEE
The machine allows you to use pre-ground and decaffeinated coffee. Pre-ground coffee must be poured into the appropriate compartment positioned next to the coffee bean hopper. Only use coffee ground for espresso machines and never coffee beans or instant coffee.
WARNING: ONLY PUT PRE-GROUND COFFEE INTO THE COMPARTMENT WHEN YOU WISH TO DISPENSE THIS TYPE OF BEVERAGE. ONLY INSERT ONE SCOOP OF GROUND COFFEE AT A TIME. TWO CUPS OF COFFEE CANNOT BE DISPENSED AT THE SAME TIME. The preparation of an espresso using pre-ground coffee is shown in the example given below. The customized choice of using pre-ground coffee is shown on the display.
pre-ground espresso coffee 08:33
insert ground coffee and press ok
2. 1. Select the desired beverage by navigating the click wheel with Select the function by pressing the button until the pre-ground option appears. Press the A message reminds the user to pour ground coffee into the appropriate compartment.
brewing in progress please wait
Pour one scoop of ground coffee into the appropriate compartment using the measuring scoop provided.

Press the brewing.

button to start
Note: If brewing does not start within 30 seconds from the appearance of the message (3), the machine will return to the main menu and discharge any inserted coffee into the coffee grounds drawer; If no pre-ground coffee is poured into the compartment, only water will be dispensed; If the dose is excessive or if 2 or more scoops of coffee are added, the machine will not dispense the beverage and the coffee in the compartment will be discharged into the grounds drawer.

Remove the carafe using the handle.
Gently swirl the carafe and pour the milk into the cup.
Position the cup with frothed milk under the dispensing head. Dispense coffee into the cup.

BEVERAGE PROGRAMMING

Every beverage can be programmed according to your individual tastes.
1. PROGRAMMING FOR SELF-LEARNING
You can program the quantity of coffee and/or milk you wish to be dispensed into the cups when you press the button for any beverage. Select the type of beverage you want to program, then press and hold the button until the display shows (for example): programming

espresso coffee

The machine dispenses coffee. When the required amount is reached, press the The display shows: saved

button again.

The dispensed quantity of coffee and/or milk is memorized and replaces any previous settings.
2. PROGRAMMING FROM THE BEVERAGE SETTINGS MENU
To adjust the settings for preparing beverages: press the In this phase you can: button and select beverage settings by
exit the programming mode. (see page 18)

beverage settings

restore factory settings
by navigating the click wheel with settings for: - the quantity of coffee to be brewed; - the coffee temperature; - prebrewing the coffee. - select the quantity of coffee to be ground (opti-dose) or select the function to set: - the coffee temperature; - coffee prebrewing. The following page describes how to program coffee beverages; the settings to program each beverage may differ depending on the type of beverage. save the new settings.
Check that the water and coffee bean container are full; place the cup under the dispensing head.
Select beverage settings. Press the

1.1 espresso coffee

When the settings are changed, the message on the When the changes are stored 2. 1. 2.
medium aroma espresso coffee
Select the beverage to program. Press the
a few times Press the button to adjust the quantity of coffee to be ground or select the use of preground coffee. Press the button to save.

espresso coffe +

temperature: medium espresso coffee
1. 2. Change the coffee quantity by navigating the click wheel with your. button for more than Press the two seconds to access the other settings to program.

Change the temperature setting (high, medium, low) by navigating Press the button to save.
prebrewing: normal espresso coffee
Prebrewing: the coffee is slightly dampened before brewing to bring out the full aroma of the coffee which acquires an excellent taste.
button to select the Press the prebrew setting.
Change the prebrew value (normal, long, off) by turning the click wheel with your button to save.

PROGRAMMING THE MACHINE

Some of the machines functions can be programmed to customize operations according to your individual preferences.

button to:

- save the new settings.

1 Press the 1

select the functions change the function settings.

4 energy saving

Beverage setting (see page 16)

2 machine settings 5

Energy saving (see page 31)

special functions

Machine settings (see page 19)
Special functions (see page 33)
Maintenance (see page 25) To exit the programming mode:

MACHINE SETTINGS

To change the machines operation settings, press the the
button, select machine settings and press

rinsing on

set the menu language.

2.2 water hardness 3

set the coffee circuit rinse cycle.
2.6 cup-warming surface off

set the water hardness.

2.3 acoustic alarm on
activate/deactivate the operation of the cup warming surface

2.7 clock setting

set/activate the acoustic alarms.

2.4 filter alert on

To set the current time, date and hour format to display.
activate/deactivate the Aqua Prima
To exit any level of machine settings without saving the changes made, press the button. For example:

LANGUAGE MENU

> machine settings > language. To change the language of the display.
1. 2. Select the desired language. After selected, the machine displays all the messages in the language selected.

WATER HARDNESS MENU

> machine settings > water hardness With the Water hardness function you can adapt your machine to the degree of hardness of the water you use, so that the machine will request descaling at the right moment. Hardness is expressed on a scale from 1 to 4. The machine is preset at value 3.
1 Immerse the water hardness tester included with the machine in water for one second.
Check the value. The test can be used for one measurement only.
1. 2. Set the water hardness obtained from the test and save it.

ACOUSTIC ALARM MENU

> machine settings > acoustic alarm To turn on/off a tone each time a button is pressed.
3 Select by navigating the click

It is possible to set: - on - off Press the button to save.

FILTER ALARM MENU

> machine settings > filter alert

RINSE MENU

> machine settings > rinsing The rinse setting the internal circuits in order to guarantee that the beverages are only made with fresh water. The function is enabled as default by the manufacturer. Note: This rinse cycle is performed every time the machine is turned on after the warming phase.

2.5 rinsing on

CUP WARMING SURFACE MENU
> machine settings > cup-warming surface To turn on/off the operation of the cup warming surface located on the top of the machine.A warm cup allows you to fully savour the coffee and taste its full aroma.

CLOCK SETTING MENU

> machine settings > clock setting To set the current time, date and hour format to display.
In this menu you can set: - the current time (hour and minutes) - the hour format (24 hours - AM/PM) - the current date (day - month - year day of the week) - the date format (American international).

Time setting

> machine settings > clock setting > time setting To set the current time on the machine

2.7.1 time setting 16:54

1. 2. Set the time by navigating the Save using the button.
1. 2. Set the minutes by navigating the Save using the button.

Time format

> machine settings > clock setting > time format To set the time view mode. This setting adjusts all clock functions to either am/pm or 24 hour formats.

2.7.2 time format 24h

1. 2. 2.
The machine also allows displaying the time in the American format (am/pm). 2.

Date setting

> machine settings > clock setting > date setting To set the date (day, month, year, day of the week).
2.7.3 date setting tuesday 18/04/06
1. 2. Select the day and press the
1. 2. Select the month and press the
1. 2. Select the year and press the
The day of the week is automatically set according to the set date.

Date format

> machine settings > clock setting > date format setting the date.
2.7.4 time format GG/MM/AAAA

The machine also allows displaying the date in the American format (MM/GG/AAAA).

MAINTENANCE

To access the machines maintenance programs, press the the

3.1 water filter 3.3

button, select maintenance and press

group wash

wash the Brew Group.

3.2 descaling

management menu.

WATER FILTER MENU

> maintenance > water filter
In this menu you can: - check the number of litres before replacement;

Litres remaining

> maintenance > water filter > litres left
3.1.1 water filter litres left 59
> maintenance > water filter > filter status

Filter state

3.1.2 filter status on
Select by navigating the click It is possible to set: - on - off Press the button to save.

Load filter

> maintenance > water filter > activate filter
When the cycle ends, turn the knob to the rest position ( ) and remove the container.
Place a container beneath the steam spout.
Turn the knob to the reference.

DESCALING MENU

> maintenance > descaling
In this menu you can: - check the number of litres before descaling; - carry out the machine descaling cycle. 2.
> maintenance > descaling > litres left To display how many litres of water can still be used before the machine requests a descaling cycle.
3.2.1 litres left descaling 115

Descaling cycle

> maintenance > descaling > execute now To perform the automatic descaling cycle. Descaling is necessary every 3-4 months when water dispenses more slowly than normal or when the machine indicates it. The machine must be turned on and will automatically manage the distribution of the descaling agent. A PERSON MUST BE PRESENT DURING THE OPERATION. WARNING! NEVER USE VINEGAR AS A DESCALER. Saeco descaler is recommended; however, you can use any non-toxic and/or non-harmful descaling beverage for coffee machines, commonly available in the shops. The used solution is to be disposed of according to the manufacturers instructions and/or regulations in force in the country of use.
Note: before beginning the descaling cycle make sure that: 1. a large enough container is positioned under the water spout; 2. THE AQUA PRIMA FILTER HAS BEEN REMOVED.

3.2.2 descaling execute now
Descaling is carried out at a controlled temperature. If the machine is cold, you must wait until it has reached the right temperature; otherwise you must cool the boiler as follows:
If the boiler needs to be heated, the machine does so automatically. When the heating stage is complete, the open water/steam knob message appears. Then proceed as described in point 5.

open water/steam knob

insert descaler ok to start cycle
When the following message appears, the heater is at the right temperature
Pour the descaling solution into the tank. Insert the tank into the machine.

button to start.

following message appears on the display:
descaling cycle please wait

passage [ 2/15]

fill the water tank
The machine begins to dispense the descaling solution through the hot water spout. The dispensing occurs at predetermined intervals, in order to allow the solution to be more effective.
The intervals are displayed in such a way as to check the state of progress of the process.
Remove the water tank, rinse with fresh drinking water to eliminate traces of descaling drinking water.
Insert the tank with fresh drinking water.
rinse cycle ok to start cycle

rinse cycle please wait

rinse cycle completed
Rinse the machines circuits by pressing the button.
The machine performs the rinse cycle. During the rinse cycle, the machine may require the water tank
following screen appears. Then the display shows the maintenance screen.
When descaling is complete, return to the main menu to dispense beverages.
Turn the knob until it is in the rest position ( ). Check the quantity of water in the tank and desired.

Brew Group Washing

> maintenance > group wash To clean the machines internal circuits used for brewing coffee. To wash the Brew Group, simply clean with water as shown on page 35. This wash completes maintenance of the Brew Group. We recommend using Saeco tablets, which can be purchased separately. Note: before performing this function make sure that: 1. a large enough container is positioned under the spout; 2. the appropriate tablet for cleaning the Brew Group has been inserted into the compartment for pre-ground coffee; THE WASH CYCLE CANNOT BE INTERRUPTED. A PERSON MUST BE PRESENT DURING THE OPERATION.

3.3 group wash

3.3.1 group wash do it now
insert tablet and press start

group wash please wait

Insert the tablet as shown above. Press to start.
Wait for the cycle to end.

passage [2/3]

wash cycle completed please wait
You can check the status of washing.
The Brew Group has been washed. Exiting programming mode. (see page 18)

ENERGY SAVING

To adjust the energy saving parameters, press the button, select energy saving and press the

turn-off delay 180

monday
Set the time which must pass after the last product dispensing before the machine enters the energy saving mode.

4.2 timer setting off

Set the machines turn on/off times (one setting for each day of the week)
Enable/disable the machines turn on/ off times programmed for the days of the week.

TURN OFF DELAY

> energy saving > turn-off delay By default, the off delay time is set at 180 minutes.

4.1 turn-off delay 180

It is possible to set: - 15 miniutes - min - 180 miniutes - max Press the button to save.

TIMER SETTING

> energy saving > timer setting The set times (timer) for the days of the week will only operate if this function is activated. If this is not the case, the timers will have no effect on the machines operation.

MONDAY TIMER SETTING

> energy saving > monday This and the following menus are used to set the turn on/off times for each day of the week. The procedure described below shows how to set the turn on/off times for the day of the week Monday. To set the turn on/off times for the other days of the week, follow the same procedure after selecting the desired day.

4.3 monday

4.3.1 switch on monday 8:00
4.3.2 switch off monday 8:00
1. 2. Set the turn on time by navigating the
1. 2. Set the minutes by navigating the
1. 2. Set the turn off time by navigating the
1. 2. Set the minutes by navigating the Press to exit the programming of the selected day.
You can set the turn on/off times for all the days of the week.
other days you want to program.

SPECIAL FUNCTIONS

This menu allows you to access special functions present on the machine. Press the button to access and select special function and press the button. Navigate the
reset settings execute now
restore the basic machine operating parameters.

RESTORE SETTINGS

> special function > reset settings The function for restoring all the factory settings is contained in this menu. This function is particularly important for restoring the basic parameters. ALL THE CUSTOM SETTINGS WILL BE LOST AND CANNOT BE RECOVERED. AFTER RESTORING FACTORY SETTINGS, YOU WILL NEED TO RE-PROGRAM ALL THE MACHINE FUNCTIONS, IF DESIRED.

5 special functions

5.1 reset settings execute now
reset settings are you sure?
1. 2. Select by pressing the button. Press the button to reset.
reset settings in progress.
The display shows the parameter
All parameters have been restored. Exit programming mode.

CLEANING AND MAINTENANCE

GENERAL MACHINE CLEANING
The cleaning described below must be performed once a week. Note: if water remains in the tank for several days, do not use it. WARNING! Never immerse the machine in water. If you remove grounds with the machine off or when not signaled on the display, the count of the grounds emptied into the drawer is not reset. For this reason the machine might display the empty grounds message even after preparing just a few coffees.
Switch off the machine and unplug it.
Clean the tank and the cover.
Remove the drip tray, empty and wash it.
Remove the grounds drawer.

Empty and clean it.

With the brush, clean the preground coffee compartment.
Remove the outer sleeve of the steam spout; then re-insert it.
Remove and wash the steam spout support; then re-insert it.
Clean the display with a dry cloth.

CLEANING THE BREW GROUP.

The Brew Group must be cleaned at least once a week. Wash the Brew Group with warm water. WARNING! Do not wash the Brew Group with detergents that can compromise its correct operation. Do not wash in the dishwasher.
Open the service door and remove the dregs drawer.
Press the PUSH button to remove the Brew Group.

and dry.

Make sure the Brew Group is in rest position; the two references must match.
Make sure the components are in the correct position. The hook shown must be in the correct position; to PUSH button.
The lever on the rear part of the group must be in contact with the group base.
Insert the washed and dried Brew Group. DO NOT PRESS THE PUSH BUTTON.

Insert the dregs drawer.

Close the service door.

ERROR CODES

HOW TO REMOVE THE MESSAGE seconds turn the machine on again to restore normal operation.If the problem persists, call the service centre and give the code (xx) shown on the display. Close the coffee bean hopper cover to be able to make a beverage. Put coffee beans into the provided container. Insert the brew group in its place. Insert the dregs drawer. Warning that does not block the machine. Proceed as for the next alarm. Remove the grounds drawer and empty the grounds into an appropriate container (See page 34, steps 4 and 5.). Note: The grounds drawer must be emptied only when the machine requires it and when the machine is turned on. If you empty the drawer with the machine turned off it will not record the emptying operation. In order for the machine to operate, the side door must be closed. water.

FAILURES

Any repairs must be performed by an authorized customer service center. Do not use the appliance with a defective power cord. The manufacturer or its customer service center will have to replace the power cable if damaged. (Caution! Electrical Current!) Turn off the appliance before opening the service door. Danger of burns!

CLEANING / DESCALING

For cleaning the milk and coffee circuits use only recommended detergents provided with the machine. These detergents must not be used for other purposes. Before cleaning the machine, the main switch must be turned to OFF (0), unplugged from the socket and cooled down. Keep the appliance from coming into contact with splashes of water or immersing in water. Do not dry the machines parts in conventional or microwave ovens. The machine and its components must be cleaned and washed after the machine has not been used for a certain period.

REPLACEMENT PARTS

For safety reasons, use only original replacement parts and original accessories.

WASTE DISPOSAL

- The packing materials can be recycled. - Appliance: unplug the appliance and cut the power cord. - Deliver the appliance and power cord to a service center or public waste disposal facility This product complies with eu directive 2002/96/ec. The symbol on the product or on its packaging indicates that this product may not be treated as household waste. Instead it shall be handed over to the applicable collection point for the recycling of electrical and electronic equipment. By ensuring this product is disposed of correctly, you will help prevent potential negative consequences for the environment and human health, which could otherwise be caused by inappropriate waste handling of this household waste disposal service or the shop where you purchased the product.

FIRE SAFETY

Do not use water or dry-powder extinguishers.

TECHNICAL DATA

Nominal voltage Power rating Power supply Shell material Size (w x h x d) Weight Cable length Control panel Water tank Coffee bean hopper capacity Pump pressure Boiler Coffee grinder Quantity of ground coffee Dregs drawer capacity Safety devices See label on the appliance See label on the appliance See label on the appliance ABS - Thermoplastic 320 x 370 x 400 mm - 12.60 x 14.57 x 15.Kg - 19.8 lbs 1200 mm - 47.24 Front (display 2 x 24 characters) 1.7 liters - 57.5 oz / Removable 250 grams - 8.9 oz / coffee beans 15 bar Stainless steel With ceramic burrs 7 - 10.5 grams / 0.25 - 0.37 oz. 14 Boiler pressure safety valve Double safety thermostat.

Subject to engineering and manufacturing changes due to technological developments. The machine conforms to the European Directive 89/336/EEC (Italian Legislative Decree 476 dated 04/12/92) concerning electromagnetic compatibility.