TECHNICAL DATA

Refer to rating plate underneath machine Refer to rating plate underneath machine
Do not discard this manual. Keep it for future reference. If the machine changes hands, make sure this manual accompanies the machine.
The warning triangle shows all important safety indications to ensure the users safety while operating the machine. The non-observance of the given safety instructions may cause serious injuries.
B Reference to figures, parts of the machine and control components are given by numbers or letters, as by"B" above exemplified
The inside first page of the cover of this manual shows figures relevant to the text. Keep it open for reference while reading the instructions.

Table of Contents

2=CA Technical data.. 23 Safety precautions.. 25 Controls and machine parts.. 26 Control panel description.. 26 Preparing the machine for use. 27 Power supply connection.. 27 Initial operation.. 27 Priming the system.. 28 Temperature control light.. 28 Bean hopper empty and water tank empty lights. 28 Grind.. 28 Quality of the coffee.. 28 Quality of the water. 28 Machine warm-up time. 29 Turning of the machine. 29 Preparing beverages.. 29 Espresso volume adjustment. 29 2=CA Brewing espresso.. 29 Hot water... 29 Steam... 29 Frothing milk for cappuccino.. 30 Safety devices.. 30 Electronic grinder protection. 30 Electronic pump protection. 30 Electronic temperature control. 30 Grinder safety mechanism. 30 Cleaning and maintenance.. 31 Brew group.. 31 Grinder.. 31 Descaling... 32 Storing the machine when not in use. 32 Maintenance... 32 Disposal of machine.. 32 Troubleshooting.. 32
boiler electromagnetic vibration pump 1.7 lt. capacity burr grinder drive motor, approx. 900 g/min. speed adjustable automatic after 20 sec. approx. 350 g. capacity 337 x 325 x 377 mm 8.5 kg 1.2 m yes aluminum boiler electronic approx. 2 min. approx. 3 min. unlimited, as long as water tank is full thermostats ejected automatically adjustable, 0-250 cl electronic fixed, mono-directional controlled by knob approx. 20 sec./cup approx. 30 sec./cup approx. 60 sec./cup approx. 60-90 sec./cup
thermo-formed plastic thermo-formed plastic thermo-formed plastic Italy refer to enclosed warranty card
The manufacturer reserves the right to make any technical modifications deemed necessary without prior notice.
Never place electrical parts of the machine in or near water: danger of electrical shock! Never direct steam or hot water spray toward the body: danger of burns! Use caution when using the steam/hot water tube: very warm surface may be hot to the touch!
SAFETY PRECAUTIONS B Keep out of the reach of small children Do not allow small children to play near the machine or with the machine.

Location of the machine Place the machine on a stable, flat surface. Do not place the machine outside or near hot surfaces or flames.
C Danger of burns Avoid pointing the steam or hot water toward the body or hands. Use caution when touching machine parts that become hot when the machine is on or operating. D Area around the machine For the proper functioning of the machine, it is recommended to place the machine on a stable, flat surface and in a well-lit, spacious area. E Cleaning Before cleaning the machine, make sure that the machine is turned off and that the power cord is unplugged. Wait until the machine has cooled. Never immerse the machine in water. Do not attempt to disassemble or modify any internal components of the machine.
Use the machine only for the purpose for which it has been manufactured. This espresso machine has been manufactured for household use only. Do not use the machine for any other purpose or attempt to carry out technical modifications to the machine.
Caution This espresso machine should be used only by adults who have read this instruction manual.
Power supply Never touch electrical parts: danger of shock! Make sure the power of the electrical outlet corresponds to the power indicated on the rating plate of the machine.
A Power cord If the power cord is damaged, do not attempt to use the machine. Contact your local dealer or an authorized service center.
Make sure the power cord is not placed near hot or sharp surfaces. Do not allow the cord to hang freely and do not place the cord near oil. Do not pull on the cord to move the machine. Do not yank on the cord to unplug the machine. Never touch the power cord with wet hands.
Repairs / Maintenance In the case of suspected operational problems, defects or faults, unplug the machine immediately. Never attempt to use a defective machine. Repairs should be carried out only by authorized service centers. The manufacturer declines any responsibility for the machine and its components and accessories for repairs made by unauthorized personnel. Fire In the case of a fire, use a carbon dioxide (CO2) based extinguisher. Do not use water or powder extinguishers.

CONTROLS AND MACHINE PARTS
Preparing the machine for use
The original box has been designed and manufactured to protect the machine during shipping. Keep it for future shipping or return shipping. Before setting up the machine, follow the safety precautions previously outlined.
PREPARING THE MACHINE FOR USE
Dump box Drip tray Grill Adjustable dispensing head Steam/hot water arm Steam/hot water knob Water tank Water tank cover Auto-valve for water tank Bean hopper Bean hopper cover
Grinder adjustment Service door Brew group Pre-ground coffee container Brew group handle Power cord Control panel with LED indicators Main switch
For your own safety and that of others, heed all safety precautions contained in this manual.
Do not turn the machine on or attempt to operate it if the water tank and/or the bean hopper is empty. Place the cover of the coffee container (11) on the coffee container (10). Keep within reach both the brush for cleaning and the unit key.
27 The bean hopper (10) is attached to the machine with two screws. Remove the bean hopper cover (11), fill the hopper with coffee beans (approx. 350 g.). Replace the cover. If necessary, adjust the grind setting by moving the knob (12) to position 8 (2 or 4), depending on the type of beans).

Power supply connection

Warning: Electrical current can be dangerous! Always heed all safety precautions and warnings. The machine must be connected to an A/C socket. The socket voltage must correspond to the voltage specified on the rating plate located on the underside of the machine. Never use the machine if the power cord is defective or damaged. A defective or damaged power cord should be replaced only by authorized service personnel. If an extension cord is used, make sure that it is not defective or damaged.
The bean hopper should be filled only with coffee beans. Do not fill the bean hopper with any other kind of product as damage to the machine may occur. Remove the water tank (7) from the machine, remove its cover (8), and fill the tank with cold, fresh water (approx. 1.7 l). A built-in valve on the underside of the tank prevents water from dripping. Before replacing the water tank in the machine, make sure that the bean hopper cover is properly in place.
28 Replace the water tank into the machine, seating it in its position. Then place the water tank cover on, pressing lightly to activate the automatic valve.
Control panel description
20 On/off light 21 Coffee selection button (1 or 2 cups) 22 Coffee temperature light
24 Steam temperature control light
Light on: correct temperature Light blinking: reaching correct temperature 25 Coffee volume regulator knob
26 Lights indicating water empty and bean

Initial operation

Light on: correct temperature Light blinking: reaching correct temperature If both the coffee temperature light (22) and the steam light (24) are blinking simultaneously, temperature is too high. Follow the procedure to prime the machine.
23 Steam selection button
hopper empty Light on: water tank is empty or bean hopper is empty. Fill water tank or fill bean hopper. After refilling the water tank, follow the procedure to prime the machine. Light blinking: dump box, brew group, or drip tray not properly positioned or service door not closed.
Danger! Electrical current can be dangerous! Electrical parts should never be in contact with water: danger of short-circuit. Steam and hot water may cause burns! Do not direct steam or hot water jet toward any body parts. Be careful when handling the steam/hot water arm: it becomes hot and may cause burns.
Do not overfill the water tank with water.
Fill the water tank with cold, fresh water only. Hot water and other fluids may damage the machine. Do not use carbonated (sparkling) water. Do not use the machine if the water tank is empty. Always make sure the water tank is full prior to turning on the machine. Plug the power cord into the outlet and press the main switch of the machine. The green light will come on and the internal electronics will automatically perform a self-test. You will hear some sounds, which are normal during the selftest.

PRIMING

RECOMMENDATIONS / BREWING / DISPENSING HOT WATER / STEAM
Bean hopper empty and water tank empty lights
When the bean hopper is empty, the corresponding light will come on and the grinder will automatically stop. Fill the bean hopper and reactivate the cycle by pressing the button (21). Also when the water tank is empty, the corresponding light will come on. Fill the water tank and follow the procedure for priming the system before brewing any espresso.
taste of your coffee and protect the internal surfaces from the production of harmful calcareous deposits. Drain the water tank every day, and fill it with fresh water. Absolutely never use water with carbon dioxide (aerated water)
Each espresso cycle is freshly ground, adding to a superior espresso pleasure. Before turning the machine on, make sure the steam/hot water knob is

closed.

Adjust the grinder: see instructions above. The grinder should be adjusted only when it is grinding. Making adjustments to the grinder while it is not running could cause damage.
29 Place one or two cups on the grill (3) under the dispensing head (4). Press the coffee selection button (21). The machine will brew one cup of espresso. By pressing the button twice consecutively, two cups will be brewed. To interrupt the flow, press again the coffee selection button.

Machine warm-up time

The machine may be kept turned on all day. However, if the machine is not used for a prolonged period, it is advisable to turn it off. The machine needs less than two minutes to warm up.
If the espresso flows too quickly (grind too coarse) or too slowly (grind too fine), adjust the grinder. Recommended grind setting: position 8 Flows too quickly: adjust grinder to a finer setting (6 or 7) Flows too slowly: adjust grinder to a coarser setting (9 or 10). Adjust the grind setting only when the grinder is running. Avoid extreme adjustments (for example, position 1). If espresso continues to flow at the improper speed, try a different coffee blend, as not all blends may be suitable for proper extraction with this machine. The modified grind setting can be detected only after brewing three or four espresso, since residual ground coffee remains in the grinder from the previous setting.

Priming the system

under the steam/hot water arm (5) and turn the steam/hot water knob (6) counterclockwise. The pump will automatically begin to function. When a steady stream of water is dispensed, close the knob by turning it clockwise. The machine has now been primed. Important: It is recommended to prime the system before the first use of the machine, after a prolonged unused period, or whenever the water tank has run completely dry. The priming procedure also should be carried out if the two temperature lights, for brewing (22) and for steaming (24), are blinking simultaneously. The machine is ready for use when the coffee temperature (22) light stops blinking and remains on.
30 Place a cup or another suitable container

Turning off the machine

Do not turn the machine off when it is in the process of brewing. Turn it off only upon completion of the entire brew cycle.
Preparing beverages Adjustment of the dispensing head
The dispensing head (4) is adjustable for different cup heights. Depending on the height of the cup being used, move the dispensing head up or down.

Hot water

The hot water has a separate water circuit from that of the espresso to prevent any crosscontamination. Hot water can be used to make tea, soup, infusions, etc.
30 Place a glass or cup under the steam/hot water arm (5) and slowly open the knob (6) counterclockwise. Hot water will automatically be dispensed. To stop the flow of hot water, turn the knob clockwise.

Espresso volume adjustment
Adjust the volume of the espresso for each cup by turning the knob (25). For example: position 5 = espresso position 6 = long espresso Use appropriately sized cups.

Quality of the coffee

Make sure the coffee beans you are using are fresh. It is recommended to use an espresso roast or another blend suitable for espresso. Store beans in an airtight container in a cool, dry place.
To heat milk or other beverages. Clean the steam arm with a damp, non-abrasive cloth after each use. Residual milk which hardens is more difficult to remove. Prime the machine after using the steam function to return the machine to the correct brewing temperature. The machine
Temperature control light
After turning the machine on, the coffee temperature light (22) will blink for approx. two minutes while the machine is reaching in the correct temperature. The light will stop blinking and remain on when the correct temperature has been reached.

Quality of water.

To prepare an excellent espresso, besides the blend, the grinding, and the right water temperature, the quality of water is also determining. Hence, we suggest to use water with a low content of limestone, so that to obtain a better
Brewing espresso (1 or 2 cups)
Press the coffee selection button (21) to brew one cup of espresso. If the button is pressed twice consecutively, the machine will perform two brew cycles for either one double espresso or two cups of espresso.
will automatically be prevented from brewing coffee if the correct brewing temperature has not been reached. The brewing function is automatically blocked if the machine is in the steaming function (light 24 is on). Press the steam button (23) and wait until the corresponding light comes on. The light will blink until the correct temperature has been reached. Slowly open the knob (6) counterclockwise. Allow the excess condensation to exit. When only steam is being produced, immerse the arm into the container holding the beverage to be heated.
31 Slowly open the steam knob completely and

STEAMING

Cleaning and maintenance General cleaning
Always keep your machine clean to ensure brewing quality and a longer working life of your machine. Before cleaning the machine, turn it off and unplug it. Before cleaning the machine, allow it to cool. Do not immerse the machine into water or any other fluids. Do not wash any parts of the machine in the dishwasher. Always air or hand-dry all parts of the machine; do not dry them in the oven or microwave.

CLEANING / SAFETY MECHANISMS / CLEANING 34 Remove the brew group (14) by holding its

Safety devices

If the service door is open, the machine is automatically deactivated and will not operate. It is not possible to brew espresso or produce steam if the brew group, dump box, or drip tray are not positioned in the machine.
handle and pressing on the part marked PRESS. Wash the brew group with hot water only. Do not use detergents.
35 Check the two steel filters of the brew group for eventual clogging. The upper filter can be removed for more detailed cleaning by unscrewing counterclockwise the plastic pin. A special key is provided to unscrew the pin. Thoroughly dry all the parts of the brew group, replace the filter, and screw the pin on carefully with the special key. 36 Remove the drip tray (2) to clean it thoroughly. Do not use abrasive detergents. Thoroughly dry the drip tray before replacing it. 37 Replace the brew group by holding it by its handle. It should easily but firmly click into place. Close the service door and replace the dump box.
Electronic grinder protection
The grinder will automatically stop after approx. 20 seconds when the bean hopper becomes empty. The corresponding light (26) comes on. Fill the bean hopper and press the button (21) to reactivate the espresso cycle.
Electronic pump protection
The machine will automatically stop if the water tank is empty in order to protect the pump. The light (26) will come on.
heat the beverage, using a circular movement from bottom to top. When the beverage has reached the desired temperature, close the knob and clean the arm with a damp cloth. Warning: Use extreme caution when handling the steam arm: it may be very hot! Upon completion of steaming, turn the function off by pressing the button (23). Open the steam knob again and prime the machine (the pump automatically starts) until water flows in a steady stream from the steam arm and the two lights (22 and 24) stop blinking. (See also the section above describing priming the system). Close the steam knob. The machine is now ready to brew.
Electronic temperature control
Both the brewing and the steaming temperatures are controlled so as to assure the proper temperature for each function. Espresso brewing will be automatically interrupted if the temperature is too low or too high (safety thermostat and protection against overheating).
Water tank; drip tray; dump box; dispensing head; machine housing
32 It is recommended to empty the dump box (1) daily. The water tank (7), drip tray (2), grill (3), and the dump box (1) should be cleaned with a neutral, non-abrasive detergent periodically. Dry these parts carefully. 33 The dispensing head (4) can be removed for easy cleaning. Pull it gently toward you and rinse the tubes thoroughly with hot water.

When replacing the brew group into the machine, do not press the PRESS lever. Simply hold the brew group by its handle and click it gently into place. Warning: If the brew group is not replaced or incorrectly positioned in the machine, the light (26) will blink and the machine will block itself. It will not brew espresso.

Grinder safety mechanism

Even premium beans may contain some impurities, i.e. a little pebble. The grinder has a built-in safety mechanism to prevent damage from such impurities. You will hear a strange sound if a little pebble is stuck in the grinder. Immediately turn off the machine. If the machine is not manually turned off, the grinder will automatically block itself after 20 seconds. Important: In order to avoid damaging the motor, remove the foreign object from the grinder before turning on the machine again. You may need to contact an authorized service center for help.

Grinder

Never pour water into the bean hopper: the machine could be damaged. Use only the grinder cleaning brush provided to clean the grinder. Do not clean with water or any other liquids. The grinder does not need regular maintenance. For any problems relating to the proper functioning of the grinder, please contact an authorized service center.
Frothing milk for cappuccino
Fill a container 1/3 full with cold milk. Immerse the steam arm (5) just below the milk surface. Turn the steam knob (6) open and begin moving the container in a circular motion to form a thick froth. Then immerse the arm further into the container to heat the milk.
Wipe the external housing of the machine periodically with a clean, damp, non-abrasive cloth.

Brew group

The brew group (14) should be cleaned on a regular basis, or at least once a week. Turn the machine off and open the service door (13). Remove the dump box (1) and the drip tray (2).

Descaling

Descaling is necessary if you have been using hard water or unfiltered water with your machine. Descaling removes potential limescale build-up in certain components of the machine, thus ensuring correct operation of these components in particular and your machine in general. Depending on the water hardness in your area, it is advisable to descale the machine every 3-6 months; more frequently if necessary. It is recommended to use bottled or filtered water for the longevity of your machine. Note: If you wish to descale the appliance yourself, use a descaler especially made for coffee machines. Use a product normally available on the market, that is neither toxic nor harmful. Do not use vinegar, which may damage internal components of the machine. Read the instructions for descaling that are provided with the descaling solution you have purchased. Important : Periodic descaling protects the machine from damage due to mineral accumulation and avoids costly repairs. Repairs and service work performed on a machine due to the lack of descaling are not covered under warranty.

DESCALING

Problem Possible cause/causes

TROUBLESHOOTING

If the machine will be stored for a long period of time, protect it from dust by covering it up or placing it into its original box.

Resolution

The machine does not turn on The machine is not getting power Check the power cord and plug or or the service door is open close the service door The brewing cycle does not If the light (26) is blinking: the start brew group is not positioned properly or not in machine drip tray not positioned properly or not in machine Make sure brew group is in machine and positioned properly makes sure drip tray is in machine and positioned properly

Maintenance

The machine should undergo a general cleaning and maintenance overview, as indicated in the preceding pages.

Disposal of machine

If the machine is to be disposed of for some reason, render it non-usable by cutting the power cord. Before cutting the power cord, make sure it is no longer plugged in. Bring your non-usable machine to an appropriate disposal center.
The control light (26) is turned on: - The coffee hopper is empty. - Fill the coffee hopper and restart the dispensing cycle. - The water tank is empty. - Fill the water tank, load the circuit and restart the dispensing cycle. Steam or hot water does not The steam/hot water arm is bloc- Clean the tip of the steam/hot wadispense ked ter arm with a little pin Espresso dispenses too quickly The grind setting is too coarse Espresso dispenses too slowly The grind setting is too fine Adjust the grind setting to a finer grind Adjust the grind setting to a coarser grind

Troubleshooting

In case of machine failure, defects, or suspected damage, unplug the machine immediately. You will find below a troubleshooting guide for basic problems. If the problem persists, or you deem the problem to be more serious, please contact an authorized service center for further assistance. Only specially trained service personnel are authorized to perform repair work on the machine. The manufacturer declines any responsibility for the machine, its components and accessories if repair work has been performed by unauthorized personnel. No warranty coverage will be extended in such cases.
Espresso is not hot enough
The temperature control light is Wait until the light stops blinking blinking
The machine takes too long Mineral (limescale) has accumu- Descale the machine to warm up or very little hot lated in the system water is dispensed when the hot water function is used The brew group is stuck and The brew group is unaligned cannot be removed Turn on the machine and close the service door; the brew group will automatically align itself