SyncMaster 173T/193T/170N/171N/172N/173N/ 191N/192N/193N/191T plus/153T/150N/151N/152N
Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting
On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check
Specifications General Specifications PowerSaver Preset Display Modes Information Service Terms Regulatory Natural Color For Better Display Authority

Notational

Power Installation Clean Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Grounding to prevent an electric shock
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

Installation Clean Other

Do not use a damaged or loose plug. This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire.
Use only a properly grounded plug and reoeptacle. An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. This may cause a fire.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.

Notational Power

Installation

Clean Other

Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or human body.
Place the monitor on a flat and stable surface. The monitor can cause injury by falling.
Set down the monitor carefully. It could be damaged or broken.
Do not place the monitor face down. The CDT surface may be damaged.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.
Notational Power Installation
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center.
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
Notational Power Installation Clean
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor. This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.
Keep all power adaptors apart.

Possible fire hazard.

Keep power adaptor away from any other heat source. Possible fire hazard.
Remove and discard vinyl bag from power adaptor before use. Possible fire hazard.
Always keep power adaptor in well-ventilated area.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.

H-Position

- Follow these instructions to change the horizontal position of the monitor's entire display. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the H-Position screen is displayed. 3. Push the Menu button to open the H-Position adjustment screen. 4. Use the [ - ] button or [ + ] button to change the horizontal position of the monitor's viewing area.

V-Position

- Follow these instructions to change the vertical position of the monitor's entire display. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the V-Position screen is displayed. 3. Push the Menu button to open the V-Position adjustment screen. 4. Use the [ - ] button or [ + ] button to change the vertical position of the monitor's viewing area.

Reset [Geometry Reset]

- Geometry parameters are replaced with the factory default values. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Reset screen is displayed. 3. Push the Menu button twice to open the Geometry Reset adjustment screen. 4. Push the [ + ] button to select Yes. If you don't want to reset the monitor, use the [ - ] button to select No.

Reset [Color Reset]

- Color parameters are replaced with the factory default values. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Reset screen is displayed. 3. Push the Menu button again and then press the - or + button until the Color Reset screen appears. 4. Push the [ + ] button to select Yes. If you don't want to reset the monitor, use the [ - ] button to select No.

Color Temperature

- Color temperature is a measure of the "warmth" of the image colors. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Color Temperature screen is displayed. 3. Push the Menu button to open the Color Temperature adjustment screen. 4. Press the [ - ] button or [ + ] button to select User Adjusted, Reddish, Bluish or sRGB. (When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits)

Color Control

Color Tontrol
- Follow these steps to adjust individual R,G,B color control. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Color Control screen is displayed. 3. Push the Menu button to open the Color Control adjustment screen. Use the [-] or [+] button to select R(ed) G(reen_ or B(lue) and push the Menu button 4. Press the [ - ] button or [ + ] button to adjust the color setting

Check the power cord connection and supply. Check the signal cable connection.
If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000 ) and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer.
The monitor is in PowerSaver mode. Press a key on the keyboard or move the mouse to activate the monitor and restore the image on the screen. Unlock the OSD by pressing the MENU button for at least 5 seconds. Check the signal cable connection. Make sure the video card is fully inserted in it's slot. Reboot the computer.
I cannot see the On Screen Display. The screen shows strange colors or just black and white.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD.
The screen suddenly has become
Have you changed the video card or the driver?

unbalanced.

Have you adjusted the resolution or frequency to the monitor?
Adjust the resolution and frequency at the video card. (Refer to the Preset Display Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly? For Windows ME/XP/2000 : Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.

Has the video card been set properly? Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note: If problems repeatedly occur, contact an authorized service center.

Question

How can I change the frequency?

Answer

Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

Q&A

Self-Test Feature Check
How can I adjust the resolution?
Windows ME/XP/2000 : Set the resolution at the Control Panel, Display, Settings. * Contact the video card manufacturer for details.
How can I set the Power Saving function? How can I clean the outer case/LCD Panel?
Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual). Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.

Check List Q&A

Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue.
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.

If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
The location and the position of the monitor may influence the quality and other features of the monitor. 1. If there are any woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3
feet (one meter) of the monitor.
A monitor recreates visual signals received from the PC. Therefore, if there is trouble with the PC or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or an "Video mode not supported" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.
General Model Name General
PowerSaver Preset Timing Modes

SyncMaster 173T

LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 17.0 inch diagonal 337.92 (H) x 270.336 (V) 0.264 (H) x 0.264 (V) a-si TFT active matrix 170(H) / 170(V)
RGB Analog , DVI Compliant Digital RGB. Composite H/V Sync, SOG(option), 0.7Vp-p Positive at 75 ohms Separate H/V sync,TTL level positive or negative
Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D connector, detachable Power Consumption 42W (Maximum) Dimensions (WxDxH) / Weight 368.2 x 177.0 x 394.3 mm / 5.0kg 368.2 x 58.8 x 310.1 mm(Without Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing

Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)
Note: Design and specifications are subject to change without prior notice.
SyncMaster 193T/191T plus
LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 19.0 inch diagonal 376.32 (H) x 301.056 (V) 0.294 (H) x 0.294 (V) a-si TFT active matrix 170(H) / 170(V)
Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D connector, detachable Power Consumption 42W (Maximum) Dimensions (WxDxH) / Weight 416.3 x 207.0 x 411.7 mm / 6.15kg 416.3 x 57.9 x 342.0 mm(Without Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing
SyncMaster 170N/171N/172N/173N
LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite H/V sync, SOG(option) TTL level positive or negative Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable Power Consumption 42W (Maximum) Dimensions (WxDxH) / Weight 368.2 x 177.0 x 394.3 mm / 4.7kg 368.2 x 58.8 x 310.1 mm (Without Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 17.0 inch diagonal 337.92 (H) x 270.336 (V) 0.264 (H) x 0.264 (V) a-si TFT active matrix 170(H) / 170(V)

Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness.
For example, the no. of TFT LCD pixels that is contained in this product are 3,932,160.
Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)
SyncMaster 191N/192N/193N
LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite H/V sync, TTL level positive or negative Maximum Pixel Clock 135 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable Power Consumption 45W (Maximum) Dimensions (WxDxH) / Weight 416.3 x 207.0 x 411.7 mm / 5.95kg 416.3 x 57.9 x 342.0 mm (Without Stand) VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing 1280 x 1024@60Hz 1280 x 1024@75Hz 30 ~ 81 kHz 56 ~ 75 Hz 19.0 inch diagonal 376.32 (H) x 301.056 (V) 0.294 (H) x 0.294 (V) a-si TFT active matrix 170(H) / 170(V)

SyncMaster 153T

LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog , DVI Compliant Digital RGB. Composite H/V Sync, 0.7Vp-p Positive at 75 ohms Separate H/V sync,TTL level positive or negative Maximum Pixel Clock 80 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable DVI-D to DVI-D connector, detachable Power Consumption Less than 30W Dimensions (WxDxH) / Weight 339.8 x 152.0 x 342.5 mm / 3.65kg 339.8 x 55.0 x 266.3 mm(Without Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing 1024 x 768@60Hz 1024 x 768@75Hz 30 ~ 61 kHz 56 ~ 75 Hz 15.0 inch diagonal 304.1 (H) x 228.1 (V) 0.297 (H) x 0.297 (V) a-si TFT active matrix 140(H) / 115(V)

computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 2,359,296. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)
English > Main > Specification > General
SyncMaster 150N/151N/152N
LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite H/V sync, SOG(option) TTL level positive or negative Maximum Pixel Clock 80 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable Power Consumption Less than 30W Dimensions (WxDxH) / Weight 339.8 x 152.0 x 342.5 mm / 3.2kg 339.8 x 55.0 x 266.3 mm (Without Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing 1024 x 768@60Hz 1024 x 768@75Hz 30 ~ 61 kHz 56 ~ 75 Hz 15.0 inch diagonal 304.1 (H) x 228.1 (V) 0.297 (H) x 0.297 (V) a-si TFT active matrix 140(H) / 115(V)
monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 2,359,296. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)

PowerSaver

Preset Timing Modes
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature.
SyncMaster 170N/171N/172N/173N/173T/193T/191T plus Normal Operation Power saving mode EPA/ENERGY 2000 Green, Blinking Less than 2W Power off (120Vac) (Power button) Black Less than 1W
Power Indicator Power Consumption

Green Less than 42W

SyncMaster 191N/192N/193N Normal Operation Power saving mode EPA/ENERGY 2000 Green, Blinking Less than 2W Power off (120Vac) (Power button) Black Less than 1W

Green Less than 45W

This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
SyncMaster 150N/151N/152N/153T
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. Normal Operation Green Less than 30W Power saving mode EPA/ENERGY 2000 Green, Blinking Less than 2W Power off (120Vac) (Power button) Black Less than 1W
SyncMaster 173T/193T/170N/171N/172N/173N/191N/192N/193N/191T plus
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

General PowerSaver

Table 1. Preset Timing Modes Display Mode IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1280 x 1024 VESA, 1280 x 1024 SUN, 1280 x 1024 Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 63.981 79.976 81.129 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 60.020 75.025 76.106 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 108.00 135.00 135.00 Sync Polarity (H/V) +/-/-/+ -/-/-/-/+,-/+,+/+ +/+ +/+ -/-/+/+ +/+ +/+ -/-

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
SyncMaster 153T/150N/151N/152N
English > Main > Specification > Preset Timing Modes
Table 1. Preset Timing Modes Display Mode MAC, 640 x 480 MAC, 832 x 624 IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 Horizontal Frequency (kHz) 35.000 49.726 31.469 31.469 31.469 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 Vertical Frequency (Hz) 66.667 74.551 70.086 59.940 70.087 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 Pixel Clock (MHz) 30.240 57.284 25.175 25.175 28.322 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 Sync Polarity (H/V) -/-/+/-/-/+ -/-/+,-/+,+/+ +/+ +/+ -/-/+/+

Service

Terms Regulatory Natural Color For Better Display Authority
U.S.A. : Samsung Computer Products Customer Service 400 Valley Road, Suite 201, Mt. Arlington, NJ 07856 Tel. : (973)601-6000, 1-800-SAMSUNG (1-800-726-7864) Fax. : (973)601-6001 http://www.samsungusa.com/monitor BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. 7037 Financial Drive Mississauga, Ontario L5N 6R3 Tel. : 1-800-SAMSUNG (1-800-726-7864) Fax. : (905) 542-1199 http://www.samsung.ca/ COLOMBIA : Samsung Electronics Colombia Cra 9 No 99A-02 Of. 106 Bogota, Colombia Tel.: 9-800-112-112 Fax: (571) 618 - 2068 http://www.samsung-latin.com/ e-mail : soporte@samsung-latin.com PANAMA : Samsung Electronics Latinoamerica( Z.L.) S.A. Calle 50 Edificio Plaza Credicorp, Planta Baja Panama Tel. : (507) 210-1122, 210-1133 Tel : 800-3278(FAST) http://www.samsung-latin.com/ PERU Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru Tel: 51-1-336-8686 Fax: 51-1-336-8551 http://www.samsungperu.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0,12/MIN. http://www.samsung.de/ AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 603 http://www.samsung.com.au/ ITALY : Samsung Electronics Italia S.p.a. Via C. Donat Cattin, Cernusco s/Naviglio (MI) Servizio Clienti: 199.153.153 http://www.samsung-italia.com/

IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003.
Cet appareil Numrique de classe B respecte toutes les exigences du Rglemont NMB-03 sur les quipements produisant des interfrences au Canada.
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022:1998+A1:2000 - Radio Frequency Interference EN55024:1998 - Electromagnetic Immunity of Information Technology Equipment EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics EN61000-3-3:1995 - Voltage Fluctuations

PCT Notice

VCCI This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)
AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally-labelled monitors?
In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment.The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climateinfluencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously. What does labelling involve? This product meets the requirements for the TCO'95 scheme, which provides for international environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in Sweden). The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern among other things restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company conducts its operations policy. The energy requirements include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for the user. Labelled products must meet strict environmental demands, for example in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability. TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +07 E-mail (Internet): development@tco.se Current information regarding TCO'95-approved and labelled products may also be obtained via the Internet, using the address:

TCO Development SE-Stockholm, Sweden Fax: +07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing this exception when a Mercury free alternative is available. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.

Service Terms Regulatory Natural Color

For Better Display

Authority
Information in this document is subject to change without notice. 2003 Samsung Electronics Co., Ltd. All rights reserved.
Service Terms Regulatory Natural Color For Better Display
Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.