SyncMaster 173T/193T/170N/171N/172N/173N/ 191N/192N/193N/191T plus/153T/150N/151N/152N
Main Page Safety Instructions Notational Power Installation Cleaning Other Introduction Unpacking Front Rear Setup Connecting Your Monitor Installing the Monitor Driver Automatic Manual Installing VESA compliant mounting
On-Screen Display Troubleshooting Check List Q&A Self-Test Feature Check
Specifications General Specifications PowerSaver Preset Display Modes Information Service Terms Regulatory Natural Color For Better Display Authority

Notational

Power Installation Clean Other
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Grounding to prevent an electric shock
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.

Installation Clean Other

Do not use a damaged or loose plug. This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire.
Use only a properly grounded plug and reoeptacle. An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire.
Disconnect the plug from the outlet during storms or lightening or if it is not used for a long period of time. Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. This may cause a fire.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.

Notational Power

Installation

Clean Other

Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or human body.
Place the monitor on a flat and stable surface. The monitor can cause injury by falling.
Set down the monitor carefully. It could be damaged or broken.
Do not place the monitor face down. The CDT surface may be damaged.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.
Notational Power Installation
Do not spray detergent directly on the monitor.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Do not set a glass of water, chemicals or any small metal objects on the monitor. This may cause damage, electric shock or a fire. If a foreign substance gets into the monitor, disconnect the plug and then contact a service center.
Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
Notational Power Installation Clean
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor. This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.

Keep all power adaptors apart.

Possible fire hazard.

Keep power adaptor away from any other heat source. Possible fire hazard.
Remove and discard vinyl bag from power adaptor before use. Possible fire hazard.
Always keep power adaptor in well-ventilated area.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
SyncMaster 173T/193T/191T plus/153T

Monitor andt Stand

Power Cord

Unpacking

Front Rear

Signal Cable

DVI Cable(Option)
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Quick Setup Guide
Warranty Card (Not available in all locations)
User's Guide and Driver Installation CD

Pivot S/W CD(Option)

For Multimedia model (Option)

Multimedia Speaker Stand

Sound Cable
SyncMaster 170N/171N/172N/173N/191N/192N/193N/150N/151N/152N

Monitor and Stand

Quick Setup Guide
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations)
Use this button to auto adjustment direct access. Use this button to Exit the active menu or the OSD. When push the 'Source' button, then Selects the Video signal while the OSD is off. (When the Source button is pressed to change the input mode, a message appears in the center of the screen displaying the current mode -- analog or digital input signal.) Note:If you select the Digital mode, you must connect your monitor to the graphic card with a digital port using the DVI cable. 3. MagicBright button MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently three different modes are available: Text, Internet, and Entertain. Each mode has its own preconfigured brightness value. You can easily select one of three settings by simply pressing MagicBright control buttons. These buttons allow you to highlight and adjust items in the menu. 4. Adjust buttons Use this button to open the OSD and activate a highlighted menu item. 5. Menu button Use this button to turn the monitor on and off. 6. Power button This light glows green during normal operation, and blinks green once as the 7. Power indicator monitor saves your adjustments. 1. Auto button 2. Exit button Source button Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

Connecting Your Monitor

Installing the Monitor Driver Installing VESA compliant mounting

Setup-General

1. 2-1.
Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analogue) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. Using the DVI (Digital) connector on the video card. Connect the DVI Cable to the DVI Port on the back of your Monitor. Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

3. 4. 5.

You may get a blank screen depending on the type of video card you are using, if you connect simultaneously both the D-sub and DVI cables to one computer. If you connect properly your monitor using the DVI connector but get a blank or fuzzy screen, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source.
Setup-For Multimedia model (Option)
1. Connect the power cord of the multimedia stand to the multimedia stand power port on the back of the monitor. 2. Connect a sound cable from the input source (sound card,computer,CD-ROM drive). 3. To listen in privacy,connect headphones here.

1. 2. 3. 4. 5. 6.

Speaker Power Cord On/Off Volume Bass Control Treble Control Stereo Input Jack Headphone Jack
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor. 3. Connect the monitor to the Macintosh computer using the D-SUB connection cable. 4. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Installing the Monitor Driver
Installing VESA compliant mounting
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monitor/ (Korea) http://www.samsungmonitor.com.cn/ (China)

Windows ME 1. Insert CD into the CD-ROM drive. 2. Click "Windows ME Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed. Windows XP/2000
1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver. 2. Click "Start" > "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced.".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver." and select "Install from a list or." then click "Next" button.
6. Select "Don't search ,I will." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

Connecting Your Monitor Installing the Monitor Driver

Removing the base

1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove the two screws and then remove the Stand from the LCD monitor.
Attaching a base NOTE: This monitor accepts a 100mm x 100mm VESA-compliant mounting interface pad.
1. Rear cover mounting pad 2. Mounting interface pad Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with the four screws that came with the arm-type base, wall mount hanger or other base.
SyncMaster 170N/171N/172N/173N/ 191N/192N/193N/150N/151N/152N

Brightness

Menu How to adjust
- Adjust Brightness. 1. Push the Menu button. 2. Push the Menu button to open the Brightness adjustment screen. 3. Use the [ + ] button to increase the brightness or [ - ] button to decrease the brightness. Direct Access Feature : When OSD is not on the screen, Push the [ + ] or [ - ] button to adjust brightness.

Contrast

- Adjust Contrast. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Contrast screen is displayed. 3. Push the Menu button to open the Contrast adjustment screen. 4. Use the [ + ] button to increase the contrast or [ - ] button to decrease the contrast.

Image Lock

Image Lock [Fine]
- Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Image Lock screen is displayed. 3. Push the Menu button twice to open the Fine adjustment screen. 4. Use the [ - ] button or [ + ] button to remove any noise.

How to adjust

Image Lock [Coarse]
- Image Lock is used to fine tune and get the best image by removing noises that creates unstable images with jitters and shimmers. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Image Lock screen is displayed. 3. Push the Menu button again and then press the [ - ] or [ + ] button until the Coarse screen appears. 4. Push the Menu button to open the Coarse adjustment screen. 5. Use the [ - ] button or [ + ] button to remove any noise.

H-Position

- Follow these instructions to change the horizontal position of the monitor's entire display. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the H-Position screen is displayed. 3. Push the Menu button to open the H-Position adjustment screen. 4. Use the [ - ] button or [ + ] button to change the horizontal position of the monitor's viewing area.

V-Position

- Follow these instructions to change the vertical position of the monitor's entire display. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the V-Position screen is displayed. 3. Push the Menu button to open the V-Position adjustment screen. 4. Use the [ - ] button or [ + ] button to change the vertical position of the monitor's viewing area.

Reset [Geometry Reset]

- Geometry parameters are replaced with the factory default values. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Reset screen is displayed. 3. Push the Menu button twice to open the Geometry Reset adjustment screen. 4. Push the [ + ] button to select Yes. If you don't want to reset the monitor, use the [ - ] button to select No.

Reset [Color Reset]

- Color parameters are replaced with the factory default values. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Reset screen is displayed. 3. Push the Menu button again and then press the - or + button until the Color Reset screen appears. 4. Push the [ + ] button to select Yes. If you don't want to reset the monitor, use the [ - ] button to select No.

Color Temperature

- Color temperature is a measure of the "warmth" of the image colors. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Color Temperature screen is displayed. 3. Push the Menu button to open the Color Temperature adjustment screen. 4. Press the [ - ] button or [ + ] button to select User Adjusted, Reddish, Bluish or sRGB. (When you adjust the Brightness and Contrast after sRGB mode is selected, sRGB mode exits)

Color Control

Color Tontrol
- Follow these steps to adjust individual R,G,B color control. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Color Control screen is displayed. 3. Push the Menu button to open the Color Control adjustment screen. Use the [-] or [+] button to select R(ed) G(reen_ or B(lue) and push the Menu button 4. Press the [ - ] button or [ + ] button to adjust the color setting

Halftone

- Change the opaqueness of the background of the OSD. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Halftone screen is displayed. 3. Push the Menu button to open the Halftone selection screen. 4. Use the [ - ] button or [ + ] button to select On or Off.

Language

- Follow these steps to change the language used in the menu. You can choose one of ten languages. (English, German, Spanish, French, Italian, Swedish, Russian) Note : The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Languages screen is displayed. 3. Push the Menu button to open the Languages selection screen. 4. Use the [ - ] button or [ + ] button to select the language you would like to use.

Menu Position

Menu Position(H-Position)
- You can change the horizontal position where the OSD menu appears on your monitor. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Menu Position screen is displayed. 3. Push the Menu button twice to open the H-Position adjustment screen. 4. Use the [ - ] button or [ + ] button to place the menu in the horizontal position you prefer.
Menu Position(V-Position)
- You can change the vertical position where the OSD menu appears on your monitor. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Menu Position screen is displayed. 3. Push the Menu button again and then press the [ - ] or [ + ] button until the V-Position screen appears. 4. Push the Menu button to open the V-Position adjustment screen. 5. Use the [ - ] button or [ + ] button to place the menu in the vertical position you prefer.

Menu Display Time

- The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until the Menu Display Time screen is displayed. 3. Push the Menu button to open the Menu Display Time selection screen. 4. Use the [ - ] button or [ + ] button to select 5, 10, 20, 50, 200 seconds. 20 seconds is the default value.

Display Mode

- You can see the frequency, the polarity of the operational signals and the resolution level. Note : These screens do not allow any changes to the settings, they are for information only. 1. Push the Menu button. 2. Push the [ - ] button or [ + ] button until until the Display Mode screen is displayed.

Auto Adjustment

- Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. 1. Push the Auto button. Note : To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
Note: Not Available This function doesn't work in Digital input.

OSD Lock / Unlock

OSD Lock/Unlock
1. Push and hold in the Menu button for 5 seconds or more to Lock the OSD. 2. Push and hold in the Menu button for 5 seconds or more to Unlock the OSD.

Magic Bright

1. Push the MagicBright button. Text: Normal Brightness For documentations or works involving heavy text. Internet: Medium Brightness For working with mixture of contents such as text and graphics. Entertain: High Brightness For watching motion pictures such as DVD and VCD
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the warranty card, the phone number on the Information section or contact your dealer. Check List
Q&A Self-Test Feature Check General

| For Multimedia model

General

Symptom

No images on the screen. I cannot turn on the monitor.

Check List

Is the power cord connected properly? Can you see "No Connection, Check Signal Cable" on the screen?

Solutions

Check the power cord connection and supply. (Connected using the D-sub cable) Check the signal cable connection. (Connected using the DVI cable) If you still see an (error) message on the screen when the monitor is connected properly, check to see if the monitor status is set to analogue. Press Source button to have the monitor double-check the input signal source. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/2000/XP) and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer.
If the power is on, reboot the computer to see the initial screen (the login screen), which can be seen.
Can you see "Video mode not supported" on the screen?
You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can properly handle.

Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD.
The screen suddenly has become
Have you changed the video card or the driver?

unbalanced.

Have you adjusted the resolution or frequency to the monitor?
Adjust the resolution and frequency at the video card. (Refer to the Preset Display Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly? For Windows ME/XP/2000 : Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.
Has the video card been set properly? Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note: If problems repeatedly occur, contact an authorized service center.

Question

How can I change the frequency?

Answer

Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)

computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 2,359,296. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)
English > Main > Specification > General
SyncMaster 150N/151N/152N
LCD Panel Size Display area Pixel Pitch Type Viewing Angle Synchronization Horizontal Vertical Display Color 16,194,277 Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, Composite H/V sync, SOG(option) TTL level positive or negative Maximum Pixel Clock 80 MHz Power Supply AC 90 ~ 264 VAC rms, 60/50 Hz 3Hz Signal Cable 15pin-to-15pin D-sub cable, detachable Power Consumption Less than 30W Dimensions (WxDxH) / Weight 339.8 x 152.0 x 342.5 mm / 3.2kg 339.8 x 55.0 x 266.3 mm (Without Stand) VESA Mounting Interface 75 mm x 75 mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing 1024 x 768@60Hz 1024 x 768@75Hz 30 ~ 61 kHz 56 ~ 75 Hz 15.0 inch diagonal 304.1 (H) x 228.1 (V) 0.297 (H) x 0.297 (V) a-si TFT active matrix 140(H) / 115(V)
monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the no. of TFT LCD pixels that is contained in this product are 2,359,296. Multimedia Speaker Stand Dimension (Length x Height x Depth) / Monitor Body Weight / Carton Weight Audio Input Audio Output Frequency Response Headphones Speaker Left/Right Stereo Jack , 0.5 Vrms (L) 2.2W + (R) 2.2W / THD 10% at 8 ohm 40 Hz ~ 20 KHz (-3dB) Max Output 20mW (3.5 pi Jack) 8ohm x 2 pcs, 70 x 32(mm) 220 x 253 x 208 (mm)

Free Line 120 http://www.samsung.pt/ NETHERLANDS/BELGIUM/LUXEMBOURG : Samsung Electronics Benelux B. V. Fleminglaan CP Rijiswijk, NEDERLANDS Service and informatielijn ; Belgium :0800-95214, http://www.samsung.be/ Netherlands : 0800-2295214, http://www.samsung.nl/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/ MEXICO : Samsung Electronics Mexico S.A. de C.V. Saturno 44 Col. Nueva Industrial Vallejo Del. Gustavo A. Madero C.P. 07700 Mexico D.F. Tel. 00 Fax. 02 RFC: SEM950215S98 http://www.samsung.com.mx/ IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO S.A. DE C.V. SATURNO 44 COL. NVA. INDUSTRIAL VALLEJO DEL. GUSTAVO A. MADERO C.P. 07700 MEXICO D.F. TEL. 5747-5100 RFC: SEM950215S98 EXPORTADO POR: SAMSUNG ELECTRONICS CO.,LTD. JOONG-ANG DAILY NEWS BLDG. 7 SOON-WHA-DONG CHUNG-KU, C.P.O BOX 2775, 1144 SEOUL, KOREA
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this case, flickering of the screen can be detected. To avoid this problem, there is a Flicker-free Mode using a vertical frequency over 70 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1280 X 1280, this means the screen is composed of 1280 horizontal dots (horizontal resolution) and 1280 vertical lines (vertical resolution).

Regulatory Natural Color For Better Display Authority

Service Terms

Regulatory
Natural Color For Better Display Authority
FCC Information User Instructions The Federal Communications Commission Radio Frequency Interference Statement includes the following warning: Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television receptions, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. User Information Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. If necessary, consult your dealer or an experienced radio/television technician for additional suggestions. You may find the booklet called How to Identify and Resolve Radio/TV Interference Problems helpful. This booklet was prepared by the Federal Communications Commission. It is available from the U.S. Government Printing Office, Washington, DC 20402, Stock Number 004-000-00345-4. The party responsible for product compliance: SAMSUNG ELECTRONICS CO., LTD America QA Lab of Samsung 3351 Michelson Drive, Suite #290, Irvine, CA92612 USA Tel) 949-975-7310 Fax) 949-922-8301 Warning User must use shielded signal interface cables to maintain FCC compliance for the product. Provided with this monitor is a detachable power supply cord with IEC320 style terminations. It may be suitable for connection to any UL Listed personal computer with similar configuration. Before making the connection, make sure the voltage rating of the computer convenience outlet is the same as the monitor and that the ampere rating of the computer convenience outlet is equal to or exceeds the monitor voltage rating. For 120 Volt applications, use only UL Listed detachable power cord with NEMA configuration 515P type (parallel blades) plug cap. For 240 Volt applications use only UL Listed Detachable power supply cord with NEMA configuration 6-15P type (tandem blades) plug cap.

TCO Development SE-Stockholm, Sweden Fax: +07 Email (Internet): development@tco.se Current information regarding TCO'99 approved and labelled products may also be obtained via the Internet, using the address: http://www.tco-info.com/ Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing this exception when a Mercury free alternative is available. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.