SyncMaster 245B / 245BW

Install driver

Notation

Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Ground to prevent an electric shock
When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
Do not use a damaged or loose plug.
This may cause electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. (Class l Equipment only.)
Insert the power plug firmly so that it does not come loose. A bad connection may cause fire.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. This may cause electric shock or fire.
Do not connect too many extension cords or plugs to one outlet. This may cause fire.
Do not disconnect the power cord while using the monitor. A surge may be caused by the separation and may damage the monitor.
Do not use the power cord when the connector or plug is dusty. If the connector or plug of the power cord is dusty, clean it with a dry cloth. Using the power cord with a dusty plug or connector may cause electric shock or fire.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable.

Installation

Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it will be operated for 24 hours continuously such as at airports, train stations etc. Failure to do so may cause serious damage to your monitor. Place your monitor in a location with low humidity and a minimum of dust. Failure to do so may cause electric shock or fire inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or the person carrying it.
Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. Dropping the product may cause damage to the product or the person carrying it.
Do not place the product on an unstable or small surface area. Place the product on an even and stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the product on the floor. Take care, as someone, specifically children may trip over it.
TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES. Otherwise, this may cause fire.
Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire.
Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire.
Put down the monitor carefully. Failing to do so may damage the monitor.
Do not place the monitor face down. This may damage the TFT-LCD surface.
The installation of the bracket must be done by a qualified professional. Installing the bracket by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
When installing the product, make sure to keep it away from the wall (more than 10 cm/4 inches) for ventilation purposes. Poor ventilation may cause an increase in the internal temperature of the product, resulting in a shortened component life and degraded performance.
Keep the plastic packaging (bag) out of children's reach. The plastic packaging (bag) may cause suffocation if children play with it.

Cleaning and Using

When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire.
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.

Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the SAMSUNG customer care center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause a malfunction or fire.

Others

Do not remove the cover (or back).
This may cause electric shock or fire. Refer to a qualified servicing company.
If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor - contact an authorized dealer or the Service Center. This may cause electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire. In particular, avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing electric shock or fire.
Disconnect the plug from the outlet during storms or lightning or if it is not used for a long period of time. Failure to do so may cause electric shock or fire.
Do not try to move the monitor by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor.
This may a malfunction, an electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.

Do not insert metal objects such as chopsticks, wire and tools or inflammable objects such as paper or matches into the vent, headphone port or AV ports or etc or etc. This may cause electric shock or fire. If an alien substances or water enters the product, turn the product off, unplug the power connector from the wall outlet and contact the Service Center.
When viewing a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy saving mode or set a screensaver to a changing picture when away from the monitor for an extended period of time.
Adjust the resolution and frequency to the level appropriate for the model. An inappropriate resolution may cause undesirable picture quality. 24 inch Wide (61 cm) - 1920 x 1200
Viewing the monitor continuously at a too close angle may result in damage to your eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not install the product on an unstable, uneven surface or a location prone to vibrations.
Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire.
When moving the monitor, turn off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connected to other devices, are disconnected before moving the monitor. Failure to disconnect cables may damage it and cause fire or electric shock.
Place the product out of childrens reach, as they could damage by hanging onto it. A falling product may cause injury to the person or even fatality.
When not using the product for an extended period of time, keep the product unplugged. Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, causing electric shock or fire.
Do not place your children's favorite toys or any other objects of interest on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing injury or even fatality.
When lifting up or moving the monitor, do not lift the monitor upside down while holding only the stand. This may cause your monitor to fall, and become damaged or cause personal injury.
Good Postures When Using the Monitor
Try to maintain a good posture when using the monitor. Keep your back straight. Keep a distance of about 45 ~ 50 cm between your eyes and the monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. Keep your arms level with the back of your hands. Keep the angle of the elbow perpendicular. Keep the angle of the knees at more than 90 degree. Do not let your

feet fall up from the floor. Adjust the arm position so that it is below the heart
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 20 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.

MagicBright button [ ]

Brightness button [ ]
When OSD is not on the screen, push the button to adjust brightness. >> Click here to see an animation clip Not available in MagicBright mode of Dynamic Contrast. Adjust items in the menu. Activates a highlighted menu item. / Push the ' ', then selects the video signal while the OSD is off. (When the button is pressed to change the input mode, a message
Adjust buttons [ Enter button [ ] / Source button
appears in the upper left of the screen displaying the current mode -analog or digital input signal.) If you select the digital mode, you must connect your monitor to the graphic card's DVI port using the DVI cable. >> Click here to see an animation clip AUTO button Power button [ ] Power indicator Use this button for auto adjustment. >> Click here to see an animation clip Use this button for turning the monitor on and off. This light glows blue during normal operation, and blinking blue once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
The configuration at the back of the monitor may vary from product to product.
POWER S/W / POWER POWER S/W : Switch the monitor on and off. POWER : Connect the power cord for your monitor to the POWER port on the back of the monitor.
DVI IN(HDCP) / RGB IN DVI IN(HDCP) : Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor. RGB IN : Connect the RGB IN terminal at the back of your monitor to your computer.
AUDIO POWER Connect the speaker power line connected to the speaker to the AUDIO POWER terminal of the monitor
Kensington Lock The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it.
Stand Stopper Remove the fixing pin on the stand to lift the monitor up and down.
See Connecting Cables for further information regarding cable connections.

Connecting Cables

Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use appropriate connection for your computer. Using the RGB (Analog) connector on the video card. - Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. [ RGB IN ] Using the DVI (Digital) connector on the video card. - Connect the DVI cable to the DVI IN(HDCP) port on the back of your monitor. [ DVI IN(HDCP) ] Connected to a Macintosh. Connect the monitor to the Macintosh computer using the RGB connection cable. If the monitor and the computer are connected, you can turn them on and use them.

Monitor Driver

When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Installing the Monitor Driver (Automatic) Insert the CD into the CD-ROM drive. Click "Windows". Choose your monitor model in the model list, then click the "OK" button.
If you can see following message window, then click the "Continue Anyway" button. Then click the "OK" button (Microsoft Windows XP/2000 Operating System).
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/
Monitor driver installation is completed.
Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux
Microsoft Windows Vista Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel". Then, double-click on "Appearance and Personalization".
Click "Personalization" and then "Display Settings".
Click "Advanced Settings".
Click "Properties" in the "Monitor" tab. If the "Properties" button is deactivated, it means the configuration for your monitor is completed. The monitor can be used as is. If the message Windows needs is displayed, as shown in the figure below, click "Continue".
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver" in the "Driver" tab.
Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer".
Click "Have Disk" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".

Microsoft Windows Millennium Operating System Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver." Choose "Display a list of all the driver in a specific location." then click the "Next" button. Click the "Have Disk" button. Specify A:\(D:\driver) then click the "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box.
Microsoft Windows NT Operating System Click "Start," "Settings," "Control Panel," and then double-click the "Display" icon. In the Display Registration Information window, click the Settings tab and then click "All Display Modes". Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click "OK". Click the "Apply" button if you see the screen working normally after clicking "Test". If the screen is not normal, change to a different mode (lower mode of resolution, colors, or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press "Enter" at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) "Enter" the model name of your monitor. This information will not affect the actual execution of XWindow. You have finished setting up your monitor. Execute X-Window after setting other requested hardware.

Control Buttons

[ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu. [ ] Press this button to activate a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.

Direct Functions

Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of fine, coarse and position are adjusted automatically. (Available in Analog mode only) To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on. If auto adjustment does not work properly, press 'AUTO' button again to adjust picture with more accuracy. If you change resolution in the control panel, auto function will be executed automatically.

OSD Locked & Unlock When pressing the AUTO button after locking the OSD
When pressing the MENU button after locking the OSD
Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Locked : Hold down the menu button for more than five seconds to activate the OSD adjustment lock function.

OSD Locked & Unlock

Unlock : Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function. Though the OSD adjustment lock function is activated, you can still adjust the brightness and contrast, and adjust MagicBright ( ) using the Direct button.

MagicBright

Description Push the MagicBright button to circle through available preconfigured modes.
MagicBright - seven different modes (Custom/Text/Internet/Game/Sport/Movie/Dynamic Contrast)

Brightness

Menu Brightness
Description When OSD is not on the screen, push the button to adjust brightness.

SOURCE

Menu SOURCE
Description Selects the Video signal while the OSD is off. (Analog/Digital)

OSD Function

Picture Color Image OSD Setup Information Brightness MagicColor Coarse Language Auto Source Contrast Color Tone Fine H-Position Image Reset Color Control Sharpness V-Position Color Reset Gamma H-Position Transparency V-Position Display Time
Picture : Not available in MagicBright mode of Dynamic Contrast.
Description You can use the on-screen menus to change the brightness according to personal preference.

Play/Stop

Contrast
You can use the on-screen menus to change the contrast according to personal preference.
Color : Not available in MagicBright mode of Dynamic Contrast.

Description

MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality.

MagicColor

Off Demo
Returns to the original mode. The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. Full Displays not only vivid natural color but also more realistic natural skin color with clearness. Intelligent Displays vivid natural color with clearness.

I cannot see the On Screen Display.
Have you locked the On Screen Display (OSD) Menu to prevent changes? Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
The screen shows strange colors or just black and white.
Check the signal cable connection. Make sure the video card is fully inserted in its slot.

Reboot the computer.

Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Timing Modes).
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Timing Modes). Adjust the frequency properly by referring to the video card manual and the Preset Timing Modes. (The maximum frequency per resolution may differ from product to product.) Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel Display Settings. Has the video card been set properly? There is a message that reads "Unrecognized monitor, Plug & Play Have you installed the monitor driver? Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions.
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Have the Windows colors been set properly?
(VESA DDC) monitor found".
See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Install the monitor driver according to the Driver Installation Instructions.
Check the following items if there is trouble with the monitor. Check if the power cord and the video cables are properly connected to the computer. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) If you installed a new video card or assembled the PC, please check if the adapter(video) driver and the monitor driver are properly installed. Check if the scanning ratio of the video screen is set at 56 Hz ~ 75 Hz. (Do not exceed 60 Hz when using the maximum resolution.) If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel System Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.

Specifications

General Model Name LCD Panel Size Display area Pixel Pitch Synchronization Horizontal Vertical Display Color 16.7M Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, DVI(Digital Visual Interface) Compliant Digital RGB 0.7 Vp-p 5% TTL level (V high 2.0V, V low 0.8V) Maximum Pixel Clock 154 MHz Power Supply AC 100-240 V ( 10%), 60/50Hz 3Hz Signal Cable 1920x1200@60Hz 1920x1200@60Hz 30 ~ 81 kHz 56 ~ 75 Hz 24" Wide Diagonal (61 cm) 518.48 mm (H) x 320.0 mm (V) 0.270 mm (H) x 0.270 mm (V) SyncMaster 245B / 245BW
15pin-to-15pin D-sub cable, Detachable DVI-D to DVI-D connector, Detachable Signal Connectors 15pin 3-row D-sub connector, 24pin 3-row DVI-D connector Dimensions (W x H x D) / Weight 560.0 X 368.5 X 83.0 mm / 22.0 x 14.5 x 3.3 inch (Without Stand) 560.0 X 445.5 X 250.0 mm / 22.0 x 17.5 x 9.8 inch (With Stand) / 8.4 Kg / 18.5 lbs VESA Mounting Interface 200 mm x 100 mm Environmental considerations Operating Temperature: 50F ~ 104F (10C ~ 40 C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~ 113F (-20C ~ 45 C) Humidity: 5% ~ 95%, non-condensing

Storage

Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1 ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD sub pixels that is contained in this product are 6,912,000. Design and specifications are subject to change without prior notice. Class B Equipment (Information Communication equipment for residential use) This product complies with the Electromagnetic Compatibility Directives for residential use and can be used in all areas including common residential areas. (Class B equipment emits less electromagnetic waves than Class A equipment.)

74.038

59.950

154.000

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit : Hz
Contact SAMSUNG WORLDWIDE
If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center.
North America U.S.A CANADA MEXICO Latin America ARGENTINE BRAZIL CHILE COLOMBIA COSTA RICA ECUADOR EL SALVADOR GUATEMALA JAMAICA PANAMA PUERTO RICO REP. DOMINICA TRINIDAD & TOBAGO VENEZUELA Europe 0800-333-3733 4004-0000 800-726-7864 (SAMSUNG) 01-8000112112 0-800-507-7267 1-800-10-7267 800-6225 1-800-299-0013 1-800-234-7267 800-7267 1-800-682-3180 1-800-751-2676 1-800-7267-864 0-800-100-5303 http://www.samsung.com/ar http://www.samsung.com/br http://www.samsung.com/cl http://www.samsung.com.co http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin http://www.samsung.com/latin 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01-800-SAMSUNG (7267864) http://www.samsung.com http://www.samsung.com/ca http://www.samsung.com/mx

BELGIUM CZECH REPUBLIC

000 844
http://www.samsung.com/be http://www.samsung.com/cz
DENMARK FINLAND FRANCE GERMANY HUNGARY ITALIA LUXEMBURG NETHERLANDS NORWAY POLAND PORTUGAL REPUBLIC OF IRELAND SLOVAKIA SPAIN SWEDEN SWITZERLAND U.K CIS ESTONIA LATVIA LITHUANIA KAZAKHSTAN RUSSIA UKRAINE UZBEKISTAN Asia Pacific AUSTRALIA CHINA HONG KONG
030-3260 SAMSUNG(7267864) ( 0,15/min) 01805 - 121213 ( 0,14/Min) 06-80-SAMSUNG (7267864) 800 SAMSUNG (7267864) 0032 (0)( 0,10/Min) 815-100 0800-SAMSUNG (7267864) 0771-0800-SAMSUNG (7267864)
http://www.samsung.com/dk http://www.samsung.com/fi http://www.samsung.com/fr http://www.samsung.de http://www.samsung.com/hu http://www.samsung.com/it http://www.samsung.lu http://www.samsung.com/nl http://www.samsung.com/no http://www.samsung.com/pl http://www.samsung.com/pt http://www.samsung.com/uk http://www.samsung.com/sk http://www.samsung.com/es http://www.samsung.com/se http://www.samsung.com/ch http://www.samsung.com/uk

800-7267 800-7267 8-800-1188 8-800-200-0400 8-800-503-0000 140-1234
http://www.samsung.ee http://www.samsung.com/lv http://www.samsung.lt http://www.samsung.kz http://www.samsung.ru http://www.samsung.com/ur http://www.samsung.uz
603 800-810-5858, 010- 3698-4698
http://www.samsung.com/au http://www.samsung.com.cn http://www.samsung.com/hk
INDIA INDONESIA JAPAN MALAYSIA PHILIPPINES SINGAPORE THAILAND TAIWAN VIETNAM Middle East & Africa SOUTH AFRICA U.A.E
3030 8282, 11 0800-112-8888 0120-327-527 1800-88-9999 1800-10-SAMSUNG (7267864) 1800-SAMSUNG (7267864) 1800-29-3232, 03-689-3232 0800-329-889
http://www.samsung.com/in http://www.samsung.com/id http://www.samsung.com/jp http://www.samsung.com/my http://www.samsung.com/ph http://www.samsung.com/sg http://www.samsung.com/th http://www.samsung.com/tw http://www.samsung.com/vn
(SAMSUNG) 800SAMSUNG (7267864) 8000-4726
http://www.samsung.com/za http://www.samsung.com/mea
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit : mm
Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit : Hz Example : If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit : kHz
Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.
Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function.

Resolution

The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example : If the resolution is 1920 x 1200 , this means the screen is composed of 1920 horizontal dots (horizontal resolution) and 1200 vertical lines (vertical resolution).

For Better Display

Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. Resolution : 1920 x 1200 Vertical frequency (refresh rate) : 60 Hz TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD sub pixels that is contained in this product are 6,912,000. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it. If you are not satisfied with the quality of the picture, you can get better quality of the picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after automatic adjustment, use FINE/COARSE adjustment function. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to move the picture when you need to be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice. 2007 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

TCO Certified Models
[ Last update : 28/ 06/ 2010 ] No. 19 Product Category Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Version TCO 5.0 TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 03:1002:Monitor Monitor Monitor TCO 03 TCO 03 TCO 03 03:1002:Monitor Monitor Monitor TCO 03 TCO 5.0 TCO 03 D510020150 03:1002:1516 DMonitor TCO 5.0 03:1002:Monitor TCO 03 DMonitor TCO 5.0 03:1002:1518 03:1002:1515 Certification No. D510060223 D510060218 03:1005:1537 D510050200 03:1004:1535 D510040196 03:1004:1534 D510040188 03:1004:1532 D510040184 D510040178 03:1003:1527 D510030175 D510030174 03:1003:1528 D510030170 D510030173 D510030172 D510020151 Model Name 2443DW, 2443DWX 2243DW, 2243DWX B1940EW, B1940EWX, E1920EW, E1920EWX B1940EW, B1940EWX, E1920EW, E1920EWX BX2340, BX2340X, EX2320, EX2320X BX2340, BX2340X, EX2320, EX2320X E1920NW, E1920ENW EX2020, EX2020X, BX2040, BX2040X EX2020, EX2020X, BX2040, BX2040X BX2240W BX2340 BX1940, BX1940X, EX1920, EX1920X EX1920W, E1920NW, E1920ENW B2330 E2220N EX2020 E2220N BX1940, BX1940X, EX1920, EX1920X B2440L, B2440LX, B2440, B2440X, B2440M, B2440MH, B2440MX, E2420L, E2420LX, E2420, E2420X, E2420M, E2420MH, E2420MX, E2420NL, E2420NLX, B2420NL B2440L, B2440LX, B2440, B2440X, B2440M, B2440MH, B2440MX, E2420L, E2420LX, E2420, E2420X, E2420M, E2420MH, E2420MX, E2420NL, E2420NLX, B2420NL B1940W, B1940NW, E1920W, E1920NW E1920, E1920N, E1920NX, E1920X, B1940, B1940N, B1940X, B1940NX, B1940M, B1940MX, B1940R, B1940RX, B1940MR, B1940MRX, E1920NR, E1920NRX, E1920R, E1920RX, E1945NXPLUS, E1920M, E1920MX , E1920MR, E1920MRX E2220, E2220N, B2240, B2240N, B2240M, B2240MH, B2245PLUS, B2240W, B2240MW, E2220NW, E2220W, E2220MW, B2240EW, E2220EW, B2240EMW, E2220EMW B1930N, E1920N, EX1920 (LED Back light) B1740R, B1740RX, E1720NR, E1720NRX, B1740NR, B1740NRX, E1720R, E1720RX E1920, E1920N, E1920NX, E1920X, B1940, B1940N, B1940X, B1940NX, B1940M, B1940MX, B1940R, B1940RX, B1940MR, B1940MRX, E1920NR, E1920NRX, E1920R, E1920RX, E1945NXPLUS, E1920M, E1920MX , E1920MR, E1920MRX E1920, E1920N, E1920NX, E1920X, B1940, B1940N, B1940X, B1940NX, B1940M, B1940MX, B1940R, B1940RX, B1940MR, B1940MRX, E1920NR, E1920NRX, E1920R, E1920RX, E1945NXPLUS, E1920M, E1920MX , E1920MR, E1920MRX E1920, E1920N, E1920NX, E1920X, B1940, B1940N, B1940X, B1940NX, B1940M, B1940MX, B1940R, B1940RX, B1940MR, B1940MRX, E1920NR, E1920NRX, E1920R, E1920RX, E1945NXPLUS, E1920M, E1920MX, E1920MR, E1920MRX, B1940ER, E1920ER B1740R, B1740RX, E1720NR, E1720NRX, B1740NR, B1740NRX, E1720R, E1720RX E1920N B2030

Monitor Monitor Monitor

TCO 5.0 TCO 03 TCO 5.0
D510020149 03:1002:1517 D510020146

Product Category

Version
Certification No. D510020145
Model Name E2220, E2220N, E2220NX, E2220X, B2240, B2240N, B2240X, B2240NX, B2240M, B2240MH, B2240MX, B2245PLUS, B2249MXPLUS, B2240EW, B2240EWX, E2220EW, E2220EWX, B2240EMW, E2220EMW E1920NR E1920NR E2020, E2020N, E2020NX, E2020X, B2040, B2040N, B2040X, B2040NX E2320, B2340, E2320X, B2340X, E2320N, B2340N, E2320NX, B2340NX E2020, E2020N, E2020NX, E2020X, B2040, B2040N, B2040X, B2040NX E2320, B2340, E2320X, B2340X, E2320N, B2340N, E2320NX, B2340NX BX2440, EX2420, BX2440X, EX2420X BX2440, EX2420, BX2440X, EX2420X BX2240, EX2220, BX2240X, EX2220X, BX2247PLUS BX2240, EX2220, BX2240X, EX2220X, BX2247PLUS B2230, B2230N 943SW, 943SN 943N 2494HM 943SW, 943SN P1950W P2450H 2494LW 2243WM, 2243BW, 2243BWT 943BM, 943BW, 943BWT, 943BT F2380, F2380M, F2380MX F2080, F2080M P2350, P2350G, P2350N P2050, P2050G, P2050N P2250, P2250G, P2250N, P2250W 2443BW, 2443BWT, 2443BWPLUS 943SW, 943SN, 943SWPLUS, 943SNPLUS, SN1943PLUS, 943B 2243SW, 2243SWPLUS, 2243SNPLUS, SN2243PLUS, 2243SB 2043SW, 2043SN, 2043SWPLUS, 2043SNPLUS, SN2043PLUS, PO2043SW, 2043SB 930ND 2494HS, 2494HM, 2494LW, 2494HSI 2043NW 2243NW 743E, 743A, 743APLUS, 743EPLUS, 743EM, 743EMPLUS, EM1743PLUS, 743AE 943NW 2263VW 2443BW, 2443NW, 2443FW 2443BWT, 2443BWPLUS, ' 2443BWT-TAA-1, 2443BWT-1, 2443DW 2223NW 923NW 723N 2023NW 923NW 2243NW

Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor M i Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor
TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 5.TCO 5.0 TCO 03 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 TCO 5.0 TCO 03 TCO 03 TCO 03 TCO TCO TCO TCO 03:1002:1512 D510020144 03:1002:1511 D510020141 D510020142 03:1002:1510 D510020137 03:1002:1509 D510010134 03:1001:1507 D509120127 D509100094 03:0910:1487 D509080065 D509080066 D509060027 D509060026 03:0906:1454 D509050019 D509050018 D509050016 D509040014 D509040006 D509040005 D509040007 D509040004 03:0812:1369 03:0812:1367 03:0812:1368 99:0810:3464 03:0810:1350 03:0810:1341 03:0809:1320 03:0809:1306 03:0808:1300 03:0807:1292 03:0806:1267 03:0805:1244 03:0805:1231 03:0805:1230 03:0804:1224 03:0804:1223 99:0712:3424
TCO 03 TCO 03 TCO 03 TCO 03 TCO TCO TCO TCO TCO TCO 03 99

No. 104

Product Category Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor Monitor
Version TCO 03 TCO 99 TCO 03 TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO 03 03
Certification No. 03:0712:1147 99:0712:3422 03:0712:1137
Model Name XL24 XL30 2243BW, 2243NW, 2243WM, CX2243BW CX2243WM, 2243SN, 2243QW, 2243HZ, CX2243WM, 2243BWT, 2243NW PLUS, 2243WMPLUS, 2243BWPLUS, 2243LN, 2243QW-1, 2243WM-1, 2243BWT-1, 2243BWT-TAA-1 242MP 243T, 243T 920BM 920XT, CX916XT, CX920XT, 911NT, 930XT 244T, 244TS 741MP CX716XT, 720XT, 711NT, CX716XD, 730XT XL20 XL20 Plus 275T, 275T Plus 245B, 245T, 245B Plus 225BW, 225BWG, CX223BW, CX225BW 305T, 305T Plus 920NW, 920LM, 920WM 720N BR21CS, 214T, 214TS (214TS-AS) 2243EW, 2243AW, 2243FW, CX2243EW, 2243EWPLUS 943EW, 943AW, 943EWPLUS, 943AWPLUS 2043EW, 2043AW, 2043FW 2343BW, 2343NW, 2343FW, 2343BWPLUS 2693HX 743N, CX743N, 743B, N1743 2493HM 943BW, 943N, 943NW, CX943B, CX943BM, NW1943, 943T, 943B 2043BW, 2043NW 743B, 743N, 743BM, CX743B, CX743BM, BM1743 2043BW, 2043NW, 2043WM, CX2043BW, CX2043WM 943B, 943N, 943BW, 943NW, 943BM, 943T, CX943B, CX943BM, BM1943, 943BWX, 943TM, 943N, 943BR, 943BMR, 943BWR, 943BT, 943BWT, 943BMPLUS, 943BPLUS, 943BWPLUS, 943NPLUS, 943NWPLUS, BM1943PLUS, NW1943 PLUS, 943N-1 , 943BT-1, 943BT-TAA-1, 943BWT-1, 943BWT-TAA-1, 213T 192N, 913V, 916V, 910V, 940N, 913B, 913N, 901N, 915N, 920N, 910N, 913BM, 910M, 930B, 930BF, 940B, 940BF, 931B, 910MP, 95S, 920NW, 940BE, 911N, 920NX, 932B, 911NT, 193P PLUS, 193P, 95B, 940B PLUS, 940T, CX913N, 912N, 970P, 94S, CX902S, 193V, 94V, CX918N, 9 173T, 740N, 750B, 173P+, 740T, 740B, 740BF, 731BF, 731B, 731BA, 730BA, 770P, 710M, N1750, BF1750, B1750, MP1710, 713BM+, 740BX, 740N+, CX711P, CX710P, 170T, CX703T, CX717T, CX715B, CX717B, CX702B, CX719B, CX718B, 75T, CX715T, CX716T, CX713BM, 713BM, 178T 193V, 192V, 193P+, 970P, 940N, 913B, 920N, 913N, 913TM, 950B, 940T, 940B, 940BF, 940Fn, 931BF, 931B, 930BA, 931BA, 940BW, 940BE, 940BX, 940NW, 961BF, 940UX, CX913MP, 940FN, 913TM, 931MP, CX911P, CX910P, 193P, 190T, CX903T, CX913T, 190N, CX903N, CX915N, CX NP-P330 NP-Q330, NT-Q330 NP-R539H, NT-R539H, NP-R539, NT-R539 NP-SA41H, NP-SA41 NP-E452H, NP-E452 NP-SA91

99:0711:3413 99:0711:3411 99:0708:3403 99:0706:3389 03:0706:954 99:0706:3381 99:0706:3384 99:0706:3385 03:0706:950 03:0706:948 03:0706:946 99:0706:3388 99:0702:3361 03:0702:850 03:0511:508 03:0809:1323 03:0809:1322 03:0809:1321 03:0807:1290 03:0803:1202 99:0712:3428 03:0712:1156 99:0712:3423 99:0712:3425 03:0712:1146 03:0711:1130

Monitor

TCO 03

03:0711:1129

TCO 99

99:0710:3410

99:0112:1568

03:0301:10

03:0301:9

114 115

Note Note Note Note Note Note

PC PC PC PC PC PC

TCO TCO TCO TCO TCO TCO

5.0 5.0 5.0 5.0 5.0 5.0

N310060062 N310060061 N310050056 N310050057 N310050058 N310050053

No. 168

Product Category Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note Note PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC PC
Version TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO TCO 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0 5.0
Certification No. N310050055 N310050054 N310050052 N310050051 N310040049 N310040048 N310040047 N310040050 N310040046 N310020043 N310020041 N310020042 N310020040 N310010039 N310010038 N310010035 N310010027 N310010032 N310010034 N310010028 N310010031 N310010029 N310010033 N310010030 N310010026 N310010017 N310010012 N310010022 N310010021 N310010014 N310010015 N310010019 N310010024 N310010016 N310010011 N310010023 N310010018 N310010013 N310010020 N310010025 N310010008 N310010010 N310010009 N309080005 N309080006 N309080007 N309080004 N309080003 N309080002 N309070001 07:1001:42 07:1001:43 P110030003
Model Name NP-R540H, NT-R540H, NP-R540, NT-R540 NP-E952 NP-R590, NT-R590 NP-P430 NP-R439, NT-R439 NP-R440, NT-R440 NP-R439L, NT-R439L NP-P530, NT-P530 NP-R440L, NT-R440L NP-R525, NT-R525 NP-R425, NT-R425 NP-E257 NP-N315, NT-N315 NP-X318 NP-X320, NT-X320 NP-E872H NP-R780, NT-R780 NP-E372 NP-SE81H NP-SE81 NP-SE31 NP-E872 NP-R780H NT-R780H NP-R730 NT-R730 NP-E852H NP-R430, NT-R430 NP-NB30, NT-NB30 NP-SA31 NP-R530 NT-R530 NT-N211 NP-R580, NT-R580 NP-SA81 NP-R580H, NT-R580H NP-R480, NT-R480 NT-N151 NP-E352 NP-R480L, NT-R480L NT-NB31 NP-E852 NP-SA81H NP-N150, NT-N150 NP-N220, NT-N220 NP-N210, NT-N210 SENS X420, X420, X421 SENS X520, X520, X521 R719, E271, SE20 X120, X170 N510, N511 N310 N120, N110, NC10, ND10, N118 N130, N140, NC11, N121, N131, N141 WEP 490 WEP 480 SP-M250, SP-M255

Note PC Headset Headset Projector
TCO 5.0 TCO 07 TCO 07 TCO 5.0

Certification No.

Model Name
The first TCO standard, TCO'92 is launched on the 1st of September 1992 in Berlin. TCO Certified makes it easy to choose technology designed for both usability and the environment. They ensure that the electronics are designed for the environmentally friendly and high performance. Certifications criteria are regularly updated in line with new technologies comply with international regulation such as RoHS, WEEE, Energy star - sometimes even tougher. Some achievements of the TCO certification program: 1. Annual global energy savings due to TCO certified displays in 2006 were equivalent to 4 nuclear power reactors in operation for a full year 2. Reduced hazardous flame retardant by more than 50,000 metric tonnes 3. Significant improvement in display picture quality http://www.tcodevelopment.com/