Driver Installation

Program Installation
SyncMaster 710V/910V/510M/710M/910M/712V
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Grounding to prevent an electric shock
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. This may cause a fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or human body.
Place the monitor on a flat and stable surface. The monitor can cause injury by falling.
Set down the monitor carefully. It could be damaged or broken.
Do not place the monitor face down. The CDT surface may be damaged.
Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Leave a space for ventilation between the product and the wall. Poor ventilation may cause the interior temperature to rise and lead to a fire.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or a fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire.
Do not remove cover (or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire.
Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause malfunction, an electric shock or a fire. Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. The monitor may malfunction, causing an electric shock or a fire. Then contact the Service Center.

Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time. The monitor may malfunction, causing an electric shock or a fire.
Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor. This may cause malfunction, an electric shock or a fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center.
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.
Do not insert metal objects such as utensils, wire or drill bits, or things that catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. This may cause malfunction, an electric shock or a fire. Always contact the Service Center if foreign substances/objects enter into the monitor.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model. Inappropriate resolution may cause undesirable picture quality. 17 inch - 1280 X 1024
Keep a proper distance between your eyes and the monitor screen. Sitting too close to the monitor on a continuous basis may damage eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not use the monitor where it can be exposed to strong vibrations. Exposure to strong vibrations can be a fire hazard and shorten the life of the monitor.
When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. Failure to disconnect a cable may damage it and lead to a fire or an electric shock.

SyncMaster 710V/910V/712V
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

Unpacking

Monitor

Bottom

Hanger

Manual

Quick Setup Guide

Warranty Card

User's Guide, Monitor Dirver, Natural Color software, MagicTune software CD

D-Sub Cable

Power Cord
Menu button [ ] MagicBright button [ ]
Use this button to open the on-screen menu and exits from the menu screen or closes screen adjustment menu. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons. Use this button to turn the monitor on and off./ This light glows green during normal operation, and blinks green once as the monitor saves your adjustments. When OSD is not on the screen, Push the button to adjust brightness. Use this button to navigate and select menus or adjust the menu items in the menu screen. Activate a highlighted menu item. / Use this button to auto adjustment direct access.
Power button [ ] / Power indicator Brightness button [ ] ]
2,4. Adjust buttons [ 5. Enter button [ ]/ Auto button
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.)
Power port D-sub 15-pin port
Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
See Connecting Your Monitor for further information regarding cable connections.
SyncMaster 510M/710M/910M

Audio Cable

Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons. 1) Text : Normal Brightness For documentations or works involving heavy text. 2) Internet : Medium Brightness For working with a mixture of images such as text and graphics. 3) Entertain : High Brightness For watching motion pictures such as a DVD or VCD. 4) Custom Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste.

4. Click the "Install" button in the "Warning" window.
5. Monitor driver installation is completed.

Windows XP/2000

1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 5. Monitor driver installation is completed.
Windows XP | Windows 2000 | Windows Me | Windows NT | Linux
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China) Microsoft Windows XP Operating System
1. Insert CD into the CD-ROM driver. 2. Click "Start" > "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced.".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver." and select "Install from a list or." then click "Next" button.
6. Select "Don't search ,I will." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/ 9. Click the "Close" button then click "OK" button continually.

10. Monitor driver installation is completed.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

5. 6. 7. 8. 9. 10.

Microsoft Windows Millennium Operating System 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button Specify A:\(D:\driver) then click "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. (You can get some other screen for warning message or others, then click the appreciate option for your monitor.)

Microsoft Windows NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor. This information will not affect the actual execution of XWindow. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. 1. 2. 3. 4. 5. 6. 7. 8. 9.
1. Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. These buttons allow you to adjust items in the menu. 3. These buttons allow you to adjust items in the menu. 4. Activate a highlighted menu item.
Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

MagicBright

Menu MagicBright
Description Then push the MagicBright button again to circle through available preconfigured modes. - four different mode (Custom/Text/Internet/Entertain)

Brightness

Menu Brightness Adjust Brightness.

Description

Picture

Menu Brightness

Description Adjust the Brightness. Direct Access Feature : When OSD is not on the screen, Push the button to adjust brightness. Adjust the Contrast.

Play/Stop

Contrast
Menu Color Tone Color Control Gamma
Description The tone of the color can be changed and one of four modes can be selected - Cool, normal, Warm and Custom. Follow these steps to adjust individual R,G,B color control. Select one of three pre-defined gammas.

The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly? Windows ME/2000/XP: Set the colors properly at the Control Panel Display Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.
Has the video card been set properly?
Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter(video)
driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control PanelSystemDevice Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

General

General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 17" Diagonal 337.92 (H) x 270.336 (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SyncMaster 710V
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 34W Dimensions (WxDxH)/ Weight 382.0 x 62.0 x 320.5 mm (Without Stand) 382.0 x 175.0 x 383.7 mm (with Basic Stand)/4.55kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. Note: Design and specifications are subject to change without prior notice. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. Power saving mode EPA/ENERGY 2000 Green, Blinking (Off-mode) Less than 1W
State Power Indicator Power Consumption
Normal Operation Green Less than 34W
Power Switch off Black (at 120V) Less than 1W
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 1024 VESA, 1280 x 1024 Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 68.681 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 67.500 63.981 79.976 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.062 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 75.000 60.020 75.025 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 100.00 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 108.00 108.00 135.00 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/-/+/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 31 ~ 81 kHz 56 ~ 75 Hz 19" Diagonal 376.32 (H) x 301.056 (V) 0.294mm (H) x 0.294mm (V) a-si TFT active matrix SyncMaster 910V
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 38W Dimensions (WxDxH)/ Weight 428.0 X 61.8 X 356.0 mm (Without Stand) 428.0 X 195.7 X 430.0 mm (with Basic Stand)/4.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. Note: Design and specifications are subject to change without prior notice. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing

Select Model Name

SyncMaster 710M
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 17" Diagonal 337.92 (H) x 270.336 (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SyncMaster 710M
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 34W Dimensions (WxDxH)/ Weight 381.9 X 62.0 X 342.9 mm (Without Stand) 381.9 X 175.0 X 383.9 mm (with Basic Stand)/4.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. Note: Design and specifications are subject to change without prior notice. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 19" Diagonal 376.32 (H) x 301.056 (V) 0.294mm (H) x 0.294mm (V) a-si TFT active matrix SyncMaster 910M
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 38W Dimensions (WxDxH)/ Weight 428.0 X 61.8 X 380.5 mm (Without Stand) 428.0 X 195.7 X 430.0 mm (with Basic Stand)/5.75kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. Note: Design and specifications are subject to change without prior notice. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing

General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 17" Diagonal 337.92 (H) x 270.336 (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SyncMaster 712V
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. Power saving mode EPA/ENERGY 2000 Green, Blinking (Off-mode) Less than 1W
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 1024 VESA, 1280 x 1024 Horizontal Frequency (kHz) 31,469 31,469 31,469 35,000 49,726 68,681 37,500 37,861 35,156 37,879 46,875 48,077 48,363 56,476 60,023 67,500 63,981 79,976 Vertical Frequency (Hz) 70,086 59,940 70,087 66,667 74,551 75,062 75,000 72,809 56,250 60,317 75,000 72,188 60,004 70,069 75,029 75,000 60,020 75,025 Pixel Clock (MHz) 25,175 25,175 28,322 30,240 57,284 100,00 31,500 31,500 36,000 40,000 49,500 50,000 65,000 75,000 78,750 108,00 108,00 135,00 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/-/+/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+

Service

AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 1-800-SAMSUNG (1-800-726-7864) http://www.samsung.ca/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/

THAILAND : HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING,1st-2nd Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD ,SILOM,BANGRAK BANGKOK 10500 TEL : 0-2635-2567 FAX : 0-2635-2556
UKRAINE : SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE 4 Glybochitska str. Kiev, Ukraine Tel. 8-044-4906878 Fax 8-044-4906887 Toll-free 8-800-502-0000 http://www.samsung.com.ua/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) Fax. : (0208) < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) Fax. : (01952) http://samsungservice.co.uk/ U.S.A. : Samsung Electronics America Service Division 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) http://samsungusa.com/monitor/
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs.

Plug & Play

This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1280 x 1024 , this means the screen is composed of 1280 horizontal dots (horizontal resolution) and 1024 vertical lines (vertical resolution).

For Better Display

1. Adjust computer resolution and screen injection rate (refresh rate) oncomputer as described below to enjoy the best quality of picture. You can have an uneven quality of picture in the screen if the best quality of picture is not provided in TFT-LCD. Resolution: 1280 x 1024 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. 3. When you clean the monitor and the panel outside, please apply the recommended small amount of cleaner by using soft and dry cloth and polish it. Let LCD area not to be forced but to be scrubbed out softly. If excessive force is applied, you can have a stain on it. 4. If you are not satisfied with the quality of picture, you can get better quality of picture by executing "auto adjustment function" in display screen that is appeared as window termination button is pressed. If there's still noise after automatic adjustment, use FINE/COARSE adjustment function. 5. If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.

Authority

Information in this document is subject to change without notice. 2004 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material.
Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of
Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY STAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY STAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.

SyncMaster 710V

Install drivers

Install programs

SyncMaster 710V/910V/510M/710M/910M/712V/715V/701N 713V
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Grounding to prevent an electric shock
When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. This may cause an electric shock or fire.
When not used for extended periods of time, set your PC to DPMS. If using a screen saver, set it to the active screen mode.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. This may cause a fire.

Installation

Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or human body.
Place the monitor on a flat and stable surface. The monitor can cause injury by falling.
Set down the monitor carefully. It could be damaged or broken.
Do not place the monitor face down. The LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Leave a space for ventilation between the product and the wall. Poor ventilation may cause the interior temperature to rise and lead to a fire.
When cleaning the monitor case or the surface of the TFT-LCD, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or a fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire.
Do not remove cover (or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire.
Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause malfunction, an electric shock or a fire. Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.

5. 6. 7. 8. 9. 10.

Microsoft Windows NT Operating System
1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide.
Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor. This information will not affect the actual execution of XWindow. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. 1. 2. 3. 4. 5. 6. 7. 8. 9.

Natural Color

Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software.
1. Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. These buttons allow you to adjust items in the menu. 3. These buttons allow you to adjust items in the menu. 4. Activate a highlighted menu item.
Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically.

Language

H-Position V-Positon Transparency

Display Time

Menu Image Reset Color Reset Description Image parameters are replaced with the factory default values. Color parameters are replaced with the factory default values.

Information

Menu Information
Description Shows a video source, display mode on the OSD screen.
Menu Brightness Adjust Brightness.

Description

Menu Color Tone Description The tone of the color can be changed and one of four modes can be selected - Cool, normal, Warm and Custom.

Color Control Gamma

Follow these steps to adjust individual R,G,B color balance. Select one of three pre-defined gammas.
Menu Coarse Description Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Follow these instuction to change the clearance of image. Follow these instructions to change the horizontal position of the monitor's entire display. Follow these instructions to change the vertical position of the monitor's entire display.
Menu Image Reset Color Reset
Description Image parameters are replaced with the factory default values. Color parameters are replaced with the factory default values.
Menu Information Description Shows a video source, display mode on the OSD screen.

Overview

Install

OSD Mode

Color Calibration

Uninstall

Troubleshooting

What is MagicTune?

Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging. Proper adjustment (tuning) requires an easy to use program that goes through a step-by-step process to obtain the best overall picture quality. In most cases even simple adjustments to Brightness, or Contrast require navigation of the multi-level, onscreen display (OSD) menus that are not easy to understand. Furthermore, there is no feedback to assist in correctly setting the controls of the monitor. MagicTune is a software utility that guides you through the tuning process with easy to understand instructions and back ground patterns designed for each monitor control. The display settings for each user can be saved, providing an easy way to select display characteristics in a multiuser environment, or having a single user have multiple defined presets based on content and ambient lighting.

Basic Functionality

MagicTune is a software utility that allows monitor adjustment and color tuning using the Display Data Channel Command Interface (DDC/CI) protocol. All adjustments to the display are controlled via software to eliminate the need to use the monitor on-screen display (OSD). MagicTune supports Windows 98SE, Me, 2000, NT, XP Home, and XP Professional. MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you.
The OSD mode allows easy adjustment of monitor settings without taking pre-defined steps. You can access the desired menu item to set with ease.
1. 2. 3. Insert the installation CD into the CD-ROM drive. Click the MagicTune installation file. Select installation Language, Click "Next".
When the InstallShield Wizard window appears, click "Next."
Select "I agree to the terms of the license agreement" to accept the terms of use.
Choose a folder to install the MagicTune program.
Click "Install."
The "Installation Status" window appears.
Click "Finish."
When the installation is complete, the MagicTune 2.5 executable icon appears on your desktop.
Double-click the icon to start the program. Magictune execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key.
The following window appears if the installation is successful.
The following error message indicates that the system is using a video card that is not supported by MagicTune.

Installation Problems

The installation of MagicTune 2.5 can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.

System Requirements

OS Windows Windows Windows Windows Windows Windows Hardware 32MB Memory above 25MB Hard disk space above 98 SE Me NT 2000 XP Home Edition XP Professional
* For more information, visit the MagicTune website.
MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Pivot is functioning, part of Magictune Program may not operate normally.

The OSD mode makes the adjustment of settings on all monitors easy. When selected , each tab on top of the control window displays the general descriptions of the sub-menu items for adjustment. When selected, each tab displays a list of menus. For quick adjustment of the monitor settings, the OSD mode allows easy and convenient access to all tabs and sub-menu items.

Button Tab Definition

OK Applies any changes made and exits MagicTune.
Restores the display settings to the factory settings.

Cancel

Exits MagicTune without applying the changes made. If you have not made any changes in the control window, clicking "Cancel" does not cause any actions.

Picture Tab Definition

Allows the user to adjust the screen settings to the desired values.
i j k l m n Brightness n Contrast n Resolution n MagicBright j k l m j k l m j k l m
Makes the entire screen brighter or darker. The detailed data of the images in the dark areas can be lost if the brightness is not adjusted to the proper level. Adjust the brightness for best viewing conditions.
Adjusts the difference in brightness between the bright and dark areas on screen. Determines the crispness of the images.

Resolution

Lists all display resolutions supported by the program. MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet, Entertain and Custom. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing the MagicBright control button.
MagicBright 1. 2. 3. 4. Text: For documentations or works involving heavy text. Internet: For working with a mixture of images such as text and graphics. Entertain: For watching motion pictures such as a DVD or VCD. Custom: Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu.

Color Tab Definition

Adjusts the "warmth" of the monitor background or image color.
i j k l m n Color Tone n Color Control n Calibration j k l m j k l m
The tone of the color can be changed. Color Tone Warm - Normal - Cool Custom Adjusts of the monitor image color. You can change the monitor color to your desired color. R- G - B The process through which the colors of your choice are optimized and maintained. You will find MagicTune extremely useful if you are one of those who wish to view images with their full details accurately reproduced - including web images and ones produced by a digital camera or scanner.

Color Control

Calibration

Image Tab Definition

Adjusts the Fine , Coarse and Position values.
i j k l m n Image Setup n Position j k l m

Image Setup

Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Auto Setup : Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. Adjusts the screen location horizontally and vertically.

Position

Option Tab Definition
You can configure MagicTune using the following options.
Loads the Preferences Dialog Box. Preferences in use will have an "V" in the check box. To turn on or off any Preference, position the cursor over the box and click.

Preferences

Enable task tray menu. - To access the MagicTune menus, click the icon on the [task tray menu]. The menus are not displayed if the [Enable System Tray] is deselected in [Options] ' [Basic Settings]. Select Language - The language chosen affects only the language of the OSD.

Source Select

Analog Digital

Support Tab Definition

Shows the Asset ID and the version number of the program, and allows you to use the Help feature.
Visit the MagicTune website or click to open the Help files (User Manual) if you need any help installing or running MagicTune. The User Manual opens within a basic browser window.

Asset ID

Opens a monitor info window showing the manufacturing date of the monitor.

Version

Displays the version of MagicTune.

1. Color Calibration

Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition. 1. 2. Control "Brightness control bar" for matching the brightness of control patch and the brightness of background pattern When you detect specific color tone on "Control patch", move the control cursor toward to the direction of the color tone referring to "Color reference Circle". => Adjustment is finished properly, you won't detect any color tone on Control patch. When you finish adjustment for step1,Click "Next" button. Repeat 1), 2), 3) procedures for remaining step2 ~ step5. You can easily view the calibration effect through clicking "Preview " button!

Has the video card been set properly?
Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported.
Check the following items if there is trouble with the monitor.
1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter(video)
driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control PanelSystemDevice Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Q&A

Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control PanelDisplaySettings. * Contact the video card manufacturer for details. How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual). Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue.
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 31 ~ 81 kHz 56 ~ 75 Hz 19" Diagonal 376.32 (H) x 301.056 (V) 0.294mm (H) x 0.294mm (V) a-si TFT active matrix SyncMaster 910V
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 38W Dimensions (WxDxH)/ Weight 428.0 X 61.8 X 356.0 mm (Without Stand) 428.0 X 195.7 X 430.0 mm (with Basic Stand)/4.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable
Normal Operation Green Less than 38W
Power Switch off Black (at 230V) Less than 1W
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1024 x 768@60 Hz 1024 x 768@75 Hz 31 ~ 61 kHz 56 ~ 75 Hz 15" Diagonal 304.1 (H) x 228.1 (V) 0.297mm (H) x 0.297mm (V) a-si TFT active matrix SyncMaster 510M
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 25W Dimensions (WxDxH)/ Weight 353.9 X 57.0 X 304.7 mm (Without Stand) 353.9 X 175.0 X 344.7 mm (with Basic Stand)/4.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. Power saving mode EPA/ENERGY 2000 Green, Blinking (Off-mode) Less than 1W(115Vac) Less than 1.5W(230Vac)
Normal Operation Green Less than 25W
Power Switch off Black Less than 1W(115Vac) Less than 1.5W(230Vac)
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/+/+ +/+ +/+ -/-/+/+

Select Model Name

SyncMaster 710M
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 17" Diagonal 337.92 (H) x 270.336 (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SyncMaster 710M
Signal Cable 15pin-to-15pin D-sub cable, attatch Power Consumption(maximum) Less than 38W Dimensions (WxDxH)/ Weight 381.9 X 62.0 X 342.9 mm (Without Stand) 381.9 X 175.0 X 383.9 mm (with Basic Stand)/4.8kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable

MEXICO : SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V. MXICO : Via Lopez Portillo No. 6, Col. San Francisco SAMSUNG ELECTRONICS MXICO. S.A. de C.V. Chilpan Tultitlan, Estado de Mexico C.P. 54940. Mexico D.F. Mexico Va 01(55) 5317 2551/3410/3409 Tel: Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitln, Estado 3377 Fax: 01(55) 5317de Mxico, C.P. 54940 Tel: 01-55-5747-5100 RFC: SEM950215S98/ 01-800-726-7864 Fax: 01-55-5747-5202 / 01-800-849-1743 http://www.samsung.com.mx/ RFC: SEM950215S98 http://www.samsung.com.mx/ IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V. Via Lopez Portillo No. 6, Col. San Francisco IMPORTADO POR: Chilpan Tultitlan, Estado de Mexico C.P. 54940. Mexico D.F. Mexico SAMSUNG ELECTRONICS MXICO. S.A. de C.V. Va Lopez Portillo2551/3410/3409 Fco. Chilpan Tel: 01(55) 5317 No. 6, Col. San Tultitln, Estado de Mxico, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD. 416, Mae tan-3dong, Yeongtong-gu, EXPORTADO POR: Samsung Electronics CO.,LTD. Suwon City, Kyoungki-Do Korea 416, Mae tan-3dong, Yeongtong - gu, Suwon City, Gyeonggi-do Korea
NETHERLANDS/BELGIUM/LUXEMBOURG : Samsung Electronics Benelux B. V. Fleminglaan CP Rijiswijk, NEDERLANDS Service and informatielijn ; Belgium :0800-95214, http://www.samsung.be/ Netherlands : 0800-2295214, http://www.samsung.nl/ PANAMA : Samsung Electronics Latinoamerica( Z.L.) S.A. Calle 50 Edificio Plaza Credicorp, Planta Baja Panama Tel. : (507) 210-1122, 210-1133 Tel : 800-3278(FAST) http://www.samsung-latin.com/ PERU : Servicio Integral Samsung Av.Argentina 1790 Lima1. Peru Tel: 51-1-336-8686 Fax: 51-1-336-8551 http://www.samsungperu.com/ PORTUGAL : SAMSUNG ELECTRONICA PORTUGUESA S.A. Rua Mrio Dioniso, No2 - 1 Drt. 2795-140 LINDA-A-VELHA Tel. 114/100 Fax. 133/128 Free Line 120 http://www.samsung.pt/ SOUTH AFRICA : Samsung Electronics,5 Libertas Road, Somerset Office Park, Bryanston Ext 16. Po Box 70006, Bryanston,2021, South Africa Tel : 0027-11-549-1621 Fax : 0027-11-549-1629 http://www.samsung.co.za/ SWEDEN/DENMARK/NORWAY/FINLAND : Samsung Electronics AB Box 713 S-UPPLANDS VSBY SVERIGE Besksadress : Johanneslundsvgen 4 Samsung support Sverige: 020-46 Samsung support Danmark : 8088-4646 Samsung support Norge: 8001-1800 Samsung support Finland: 0800-118001 Tel +00 Fax +50 http://www.samsung.se/
THAILAND : HAI SAMSUNG SERVICE CENTER MPA COMPLEX BUILDING,1st-2nd Floor 175 SOI SUEKSA VIDHAYA SATHON SOI 12 SILOM ROAD ,SILOM,BANGRAK BANGKOK 10500 TEL : 0-2635-2567 FAX : 0-2635-2556
UKRAINE : SAMSUNG ELECTRONICS REPRESENTATIVE OFFICE IN UKRAINE 4 Glybochitska str. Kiev, Ukraine Tel. 8-044-4906878 Fax 8-044-4906887 Toll-free 8-800-502-0000 http://www.samsung.com.ua/ United Kingdom : Samsung Electronics (UK) Ltd. Samsung House, 225 Hook Rise South Surbiton, Surrey KT6 7LD Tel. : (0208) Fax. : (0208) < European Service Center & National Service > Stafford Park 12 Telford, Shropshire, TF3 3BJ Tel. : (0870) Fax. : (01952) http://samsungservice.co.uk/ U.S.A. : Samsung Electronics America Service Division 400 Valley Road, Suite 201 Mount Arlington, NJ 07856 1-800-SAMSUNG (1-800-726-7864) http://samsungusa.com/monitor/

IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numrique de classe B respecte toutes les exigences du Rglemont NMB-03 sur les quipements produisant des interfrences au Canada.
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022:1998+A1:2000 - Radio Frequency Interference EN55024:1998 - Electromagnetic Immunity EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics EN61000-3-3:1995 - Voltage Fluctuations

PCT Notice

VCCI This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)
AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally-labelled monitors? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment.The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature.

There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of conventional electricity generation have a negative effect on the environment (acidic and climate-influencing emissions, radioactive waste, etc.) it is vital to conserve energy. Electronic equipment in offices consumes an enormous amount of energy, since it is often routinely left running continuously. What does labelling involve? This product meets the requirements for the TCO'95 scheme, which provides for international environmental labelling of monitors. The labelling scheme was developed as a joint effort by the TCO (The Swedish Confederation of Professional Employees), Naturskyddsforeningen (The Swedish Society for Nature Conservation) and NUTEK (The National Board for Industrial and Technical Development in Sweden). The requirements cover a wide range of issues: environment, ergonomics, usability, emission of electrical and magnetic fields, energy consumption and electrical and fire safety. The environmental demands concern among other things restrictions on the presence and use of heavy metals, brominated and chlorinated flame retardants, CFCs (freons), and chlorinated solvents. The product must be prepared for recycling and the manufacturer is obliged to have an environmental plan, which must be adhered to in each country where the company conducts its operations policy. The energy requirements include a demand that the monitor after a certain period of inactivity shall reduce its power consumption to a lower level, in one or more stages. The length of time to reactivate the monitor shall be reasonable for the user. Labelled products must meet strict environmental demands, for example in respect of the reduction of electric and magnetic fields, along with physical and visual ergonomics and good usability. TCO Development Unit 1996-11-29 On the page this folder you will find a brief summary of the environmental requirements met by this product. The complere environmental criteria document may be ordered from: TCO Development Unit S-11494 Stockholm Sweden Fax: +07 E-mail (Internet): development@tco.se Current information regarding TCO'95-approved and labelled products may also be obtained via the Internet, using the address:

http://www.tco-info.com/

TCO'95 is a co-operative project between(3 logos) Environmental Requirements Brominated flame retardants are present in printed circuit boards, cables, wires, casings and housings. In turn, they delay the spread of fire. Up to thirty percent of the plastic in a computer casing can consist of flame retardant substances. These are related to another group of environmental toxins, PCBs, which are suspected to give rise to similar harm, including reproductive damage in fish eating birds and mammals, due to the bioaccumulative processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. TCO'95 demand requires that plastic components weighing more than 25 grams must not contain organically bound chlorine and bromine. Lead Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. TCO'95 requirement Permits the inclusion of lead since no replacement has yet been developed. Cadmium Cadmium is present in rechargeable batteries and in the colour generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of cadmium. The colour-generating layers of display screens must not contain any cadmium. Mercury Mercury is sometimes found in batteries, relays and switches. Mercury damages the nervous system and is toxic in high doses. TCO'95 requirement states that batteries may not contain more than 25 ppm (parts per million) of mercury. It also demands that no mercury is present in any of the electrical or

Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Ex)
Recommended settings: Bright colors with little difference in luminance - Change the characters color and background color every 30 minutes Ex)
- Every 30 minutes, change the characters with movement. Ex)
The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel. The voltage difference between electrodes increases with time, forcing the liquid crystal to lean. When this occurs, the previous image may be seen when the pattern is changed. To prevent this, the accumulated voltage difference must be decreased.
Our LCD Monitor satisfies ISO13406-2 Pixel fault Class II