To prevent rainwater from running along the outdoor antenna cable and entering the house, be sure the outdoor portion of the cable hangs down below the point of entry. If rainwater enters the product, it may cause an electric shock or fire.
If you are using an outdoor antenna, be sure to put sufficient distance between your antenna and the electrical wires nearby so that they would not come in contact with each other in case the antenna is knocked over by strong wind. A knocked-over antenna may cause injury or an electric shock.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector may cause an electric shock or fire.
Make sure to unplug the power cord before cleaning the product. Otherwise, this may cause electric shock or fire.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent.
Contact the Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire.

Others

Do not remove cover (or back). This may cause an electric shock or fire. Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire.
Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause malfunction, an electric shock or fire. Especially avoid operating the monitor near water or outdoors where the monitor could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. Then contact the Service Center. The monitor may malfunction, causing an electric shock or fire.

Place the product out of children's reach, as they could damage it by hanging onto it. A falling product could cause physical damage even death.
When not using the product for an extended time period, keep the product unplugged Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
Do not place children's favorite objects (or anything else that may be tempting) on the product. Children may try to climb on the product to retrieve an object. The product could fall, causing physical damage or even death.
When you remove batteries from the remote control, be careful that they are not swallowed by children. Keep batteries out of the reach of children.
If swallowed, see a doctor immediately.
When replacing batteries, place the batteries in the correct +/- polarity position as indicated on battery holder. Incorrect polarity may cause a battery to break or leak and could lead to fire, injury, or contamination (damage).
Use only specified standard batteries. Do not use new and used batteries together. This may cause a battery to break or leak and could lead to fire, injury, or contamination (damage).
The battery (and rechargeable battery) are not ordinary refuse and must be returned for recycling purposes. The customer is responsible for returning the used or rechargeable battery for recycling purposes as the consumer of the battery. The customer can return the used or rechargeable battery to a nearby public recycling center or to a store selling the same type of the battery or rechargeable battery.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Contact a local dealer to buy optional items.

Unpacking

Monitor

Manual

Quick Setup Guide
Warranty Card (Not available in all locations)
User's Guide, Monitor Driver, Natural Color software

D-Sub Cable

Power Cord

Audio Cable

Remote Control Remote Control This remote control is used This remote control is used in all countries except for in China only. China.

Batteries (AAA X 2)

1. SOURCE 6. MENU
2. MagicBright 7. Power button
3. AUTO / EXIT 8. Power indicator
4. CH 9. Remote Control Sensor

5. VOL 10. Speaker

1. SOURCE Switches from PC mode to Video mode. Changing the source is allowed only in external devices that are connected to the monitor at the time. To switch Screen modes: [PC] [TV] [AV] [S-Video] >>Click here to see an animation clip For more information > Broadcasting Systems 2. MagicBright MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. ( Entertain Internet Text Custom ) >>Click here to see an animation clip - Available in PC Mode only 3. AUTO / EXIT AUTO : Adjusts the screen display automatically. >>Click here to see an animation clip - Available in PC Mode only EXIT : Exits from the menu screen. 4. CH Moves from one menu item to another vertically or adjusts selected menu values. In TV mode, selects TV channels. >>Click here to see an animation clip VOL Moves from one menu item to another horizontally or adjusts selected menu values. Adjusts the audio volume. >>Click here to see an animation clip

6. MENU Use this button to open the on-screen menu and step back in the menu. 7. Power button Use this button to turn the monitor on and off. 8. Power indicator Power Indicator shows PowerSaver mode by green blinking. 9. Remote Control Sensor Aim the remote control towards this spot on the Monitor. 10. Speaker You can hear sound by connecting the soundcard of your PC to the monitor.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.)
1. POWER-IN This product may be used with 100 ~ 240VAC(+/- 10%).
2. PC Computer Connection Terminal (15 Pin D-SUB)
3. TV TV Connection Terminal For more information > Connecting TV

4. AUDIO(ST)

Audio Connection Terminal
5. Video Connection Terminal 1. Headphone Connection Terminal (Output) 2. Left(L) / Right(R) Audio Connection Terminal (Input) 3. Video Connection Terminal (Input) 4. S-Video Connection Terminal (Input)
See Connecting the Monitor for further information regarding cable connections.

Remote Control

The performance of the remote control may be affected by a TV or other electronic devices operated near the monitor, causing malfuction due to interference with frequency.
1. POWER 2. number 3. -/-4. (Volume) 5. MUTE 6. TTX/MIX 7. MENU 8. ENTER 9. P 10. SOURCE 11. INFO 12. EXIT 13. Up-Down Left-Right Buttons 14. AUTO / PRE-CH 15. (MagicBright) 16. DUAL l - ll 17. SLEEP 18. P.MODE
1. POWER Use this button to turn the monitor on and off. 2. number Selects TV channels in the TV mode. You may use this button in PIP mode as well. 3. -/-- (One/Two-Digit CHANNEL selection ) Use to select a CHANNEL numbered ten or over. Press this button, and the "--" symbol is displayed. Enter the two-digit CHANNEL number. 4. (Volume) Adjusts the audio volume.
5. MUTE Pauses (mutes) the audio output temporarily. Displays on the lower left corner of the screen. The audio resumes if Mute or (Volume) is pressed in the Mute mode. 6. TTX/MIX TV channels provide written information services via teletext. For more information > TTX / MIX 7. MENU Use this button to open the on-screen menu and step back in the menu. 8. ENTER Activates a highlighted menu item. 9. P In TV mode, selects TV channels. 10. SOURCE Switches from PC mode to Video mode. Changing the source is allowed only in external devices that are connected to the monitor at the time. [PC] [TV] [AV] [S-Video] 11. INFO Current picture information is displayed on the upper left corner of the screen. 12. EXIT Exits from the menu screen. 13. Up-Down Left-Right Buttons Moves from one menu item to another horizontally, vertically or adjusts selected menu values. 14. AUTO / PRE-CH PC mode : Adjusts the screen display automatically. TV mode : This button is used to return to the previous channel immediately. 15. (MagicBright) PC Mode : MagicBright is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. ( Entertain Internet Text Custom )

2. Double click the "Display" Icon. 3. Choose the "Settings" tab and then click "Advanced.". 4. Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. 5. Click "Driver" and then click on "Update Driver." then click on the "Next" button. 6. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver). 8. Click the "Open" button, then click "OK" button. 9. Choose your monitor model and click the "Next" button then click "Next" button. 10. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.
Microsoft Windows Millennium Operating System Click "Start" , "Setting" , "Control Panel". Double click "Display" icon. Select the "Settings" tab and click "Advanced Properties" button. Select the "Monitor" tab. Click the "Change" button in the "Monitor Type" area. Choose "Specify the location of the driver". Choose "Display a list of all the driver in a specific location." then click "Next" button. Click the "Have Disk" button Specify A:\(D:\driver) then click "OK" button. Select "Show all devices" and choose the monitor that corresponds to the one you connected to your computer and click "OK". 11. Continue choosing "Close" button and "OK" button until you close the Display Properties dialogue box. 1. 2. 3. 4. 5. 6. 7. 8. 9. 10.
Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Timing Modes in the user guide.

If you adjust picture using Custom function, MagicBright will turn to Custom mode. Colour Tone The tone of the colour can be changed. The individual colour DTVs are also user adjustabls. 1) Cool 2) Normal 3) Warm 4) Custom Adjusts the individual R, G, B Colour Controls. 1) Red 2) Green 3) Blue

Colour Control

If you adjust picture using Colour Control function, Colour Tone will turn to Custom mode. Image Lock Image Lock is used to fine-tune and get the best image by removing noise that creates unstable images with jitter and shimmer. If satisfactory results are not obtained using the Fine adjustment, use the Coarse adjustment and then use Fine again. 1) Coarse : Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. 2) Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). 3) Sharpness : Adjust the picture sharpness. 4) Position : Adjusts the screen location horizontally and vertically. The values of Fine, Coarse, Position are adjusted automatically. If you change resolution in the control panel, Auto function will be executed. - The direct button on the remote control is 'AUTO/EXIT' button.
1) Coarse 2) Fine 3) Sharpness

4) Position

Auto Adjustment

TV / AV / S-Video Mode

The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie", and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom. You can select "Custom" which automatically recalls your personalized picture settings. - The direct button on the remote control is 'P.MODE' button. 1) Dynamic 2) Standard 3) Movie 4) Custom You can use the on-screen menus to change the contrast and brightness according to personal preference. 1) Contrast : Adjusts the contrast. 2) Brightness : Adjusts the brightness. 3) Sharpness : Adjust the picture sharpness. 4) Colour : Adjust the picture colour. The tone of the colour can be changed. The individual colour components are also user adjustables. 1) Cool2 2) Cool1 3) Normal 4) Warm1 5) Warm2

Custom

Colour Tone

Available Mode

: S-Video

4. Maintenance and Cleaning 1. Maintaining the Monitor Case. Clean with a soft cloth after disconnecting the power cord.
Do not use benzene, thinner or other flammable substances, or a wet cloth.
2. Maintaining the Flat Panel Display Screen. Clean with a soft cloth (cotton flannel) smoothly. Never use acetone, benzene or thinner. (They may cause flaws or deformation of the screen surface.) We recommend a Samsung cleansing agent is used to prevent damage to the screen. The user will be required to pay costs and related expenses for repair of damages caused by him/her.
5. Symptoms and Recommended Actions A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, unavailable video mode, etc. In this case, first check the source of the problem, and then contact the service center or your dealer. 1. Check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if you installed the adapter(video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 60Hz. (The screen refresh rate must be set within in a range of 56~75hz.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver.
The following table lists possible problems and their solutions. Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Installation | Screen | Audio | Remote Control

Check List

1. Problems related to Installation Problems related to the monitor installation and their solutions are listed.
Problems PC It appears the PC does not function normally.
Solutions Check if the Display Adapter Driver (VGA Driver) is properly installed. (Refer to Installing Driver) Check if the signal cable between the computer and the monitor is securely connected and tightened. (Refer to Connecting to a Computer) Check if the TV antenna connector is securely connected to the external antenna. (Refer to Connecting TV) Check "Channel system" and make sure you choose the correct channel system. (Refer to the Channel System) Select "Auto Store" to configure the channel system automatically. (Refer to the Auto Store)

Sound is too high pitched or too low pitched
4. Problems related to Remote Control Problems related to the remote control and their solutions are listed.
Problems The remote control buttons do not respond.
Items to check Check the battery polarities (+/-). Check if the batteries have been exhausted. Check if the power is on. Check if the power cord is securely connected. Check if a special fluorescent or neon lamp is on in the vicinity.

Q&A

Question How can I change the frequency?
Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows XP : Set the resolution at the Control Panel

Appearance and

Themes Display Settings. Windows ME/2000 : Set the resolution at the Control Panel

Display

Settings.
* Contact the video card manufacturer for details. How can I set the Power Saving function? Windows XP : Set the resolution at the Control Panel Appearance and Themes Display Screen Saver. Set the function at BIOS-SETUP of the computer. (Refer to Windows/Computer Manual). Windows ME/2000 : Set the resolution at the Control Panel Display Screen Saver. Set the function at BIOS-SETUP of the computer. (Refer to Windows/Computer Manual). Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
How can I clean the outer case/LCD Panel?

General

General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16.194.277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, Separate H / V sync, Composite , 0.7Vp-p Positive at 75 ohm, TTL level positive or negative TV / Video Color system Sound system Maximum Pixel Clock 135 MHz Power Supply AC 100 ~ 240 VAC (+/- 10%), 60/50 Hz 3Hz Signal Cable 15pin to 15pin D-sub cable, Detachable Power Consumption PAL / SECAM / NTSC4.43 B/G, I, D/K SXGA 1280 x 1024@60Hz SXGA 1280 x 1024@75Hz 30 ~ 81kHz 56 ~ 75Hz 17.0 inch diagonal 337.92mm (H) x 270.336mm (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SyncMaster 710MP

Vertical Frequency (Hz) 66.667 74.551 70.086 59.940 70.087 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 60.020 75.025 76.106
Pixel Clock (MHz) 30.240 57.284 25.175 25.175 28.322 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 108.00 135.00 135.00
Sync Polarity (H/V) -/-/+/-/-/+ -/-/+,-/+,+/+ +/+ +/+ -/-/+/+ +/+ +/+ -/-
Table 2. Broadcasting Systems Note : According to broadcasting type in each country, you may not be able to select one.
NTSC Broadcasting Systems NTSC -M USA South Korea Japan Ecuador Mexico Guatemala Canada

Countries

PAL Broadcasting Systems PAL-B/G Italy Sweden Germany Norway Spain Israel Denmark Portugal Netherlands Austria Singapore Indonesia Australia PAL-D/K PAL-I PAL-N PAL-M
China North Korea Rumania
Ireland England South Africa Hongkong
Argentina Uruguay Paraguay

Brazil

SECAM Broadcasting Systems SECAM-B Iran Iraq Saudi arabia Syria Lebanon Egypt SECAM-D SECAM-K1 SECAM-L
Russia Hungary Bulgaria Poland

France

Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz

Service

The address and phone number of the company can be changed without prior notice.
AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 1-800-SAMSUNG (1-800-726-7864) http://www.samsung.ca/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/ COLOMBIA : Samsung Electronics Colombia Cra 9 No 99A-02 Of. 106 Bogota, Colombia Tel.: 9-800-112-112 Fax: (571) 618 - 2068 http://www.samsung-latin.com/ e-mail : soporte@samsung-latin.com

IC Compliance Notice This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil Numrique de classe B respecte toutes les exigences du Rglemont NMB-03 sur les quipements produisant des interfrences au Canada.
MPR II Compliance This monitor complies with SWEDAC(MPR II) recommendations for reduced electric and magnetic fields.
European Notice(Europe Only) Products with the CE marking comply with the EMC Directive(89/336/EEC), (92/31/EEC), (93/68/EEC) and the Low Voltage Directive (73/23/EEC) issued by the Commission of the European Community. Compliance with these directives implies conformity to the following European Norms: EN55022:1998+A1:2000 - Radio Frequency Interference EN55024:1998 - Electromagnetic Immunity of Information Technology Equipment EN61000-3-2:1995+A1/A2:1998 - Power Line Harmonics EN61000-3-3:1995 - Voltage Fluctuations

PCT Notice

VCCI Notice This is a Class B product based on the standard of the Voluntary Control Council for Interference by Information Technology Equipment (VCCI). If this is used near a radio or television receiver in a domestic environment, it may cause radio interference. Install and use the equipment according to the instruction manual.
TCO'95-Ecological requirements for personal computers (TCO'95 applied model only)
AB general requirements AB2 Written Eco-document acompanying the products Congratulations! You have just purchased a TCO'95 approved and labelled product! Your choice has provided you with a product developed for professional use. Your purchase has also contributed to reducing the burden on the environment and to the further development of environmentally-adapted electronic products. Why do we have environmentally-labelled monitors? In many countries, environmental labelling has become an established method for encouraging the adaptation of goods and services to the environment.The main problem as far as monitors and other electronic equipment are concerned is that environmentally harmful substances are used both in the products and during their manufacture. Since it has not been possible so far for the majority of electronic equipment to be recycled in a satisfactory way, most of these potentially damaging substances sooner or later enter Nature. There are also other characteristics of a monitor, such as energy consumption levels, that are important from both the working and natural environment viewpoints. Since all types of

Environmental requirements Flame retardants Flame retardants are present in printed circuit boards, cables, wires, casings and housings. Their purpose is to prevent, or at least to delay the spread of fire. Up to 30% of the plastic in a computer casing can consist of flame retardant substances. Most flame retardants contain bromine or chloride, and those flame retardants are chemically related to another group of environmental toxins, PCBs. Both the flame retardants containing bromine or chloride and the PCBs are suspected of giving rise to severe health effects, including reproductive damage in fish-eating birds and mammals, due to the bio-accumulative* processes. Flame retardants have been found in human blood and researchers fear that disturbances in foetus development may occur. The relevant TCO'99 demand requires that plastic components weighing more than 25 grams must not contain flame retardants with organically bound bromine or chlorine. Flame retardants are allowed in the printed circuit boards since no substitutes are available. Cadmium** Cadmium is present in rechargeable batteries and in the colour-generating layers of certain computer displays. Cadmium damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries, the colour-generating layers of display screens and the electrical or electronics components must not contain any cadmium. Mercury** Mercury is sometimes found in batteries, relays and switches. It damages the nervous system and is toxic in high doses. The relevant TCO'99 requirement states that batteries may not contain any mercury. It also demands that mercury is not present in any of the electrical or electronics components associated with the labelled unit. There is however one exception. Mercury is, for the time being, permitted in the back light system of flat panel monitors as today there is no commercially available alternative. TCO aims on removing this exception when a Mercury free alternative is available. CFCs (freons) The relevant TCO'99 requirement states that neither CFCs nor HCFCs may be used during the manufacture and assembly of the product. CFCs (freons) are sometimes used for washing printed circuit boards. CFCs break down ozone and thereby damage the ozone layer in the stratosphere, causing increased reception on earth of ultraviolet light with e.g. increased risks of skin cancer (malignant melanoma) as a consequence. Lead** Lead can be found in picture tubes, display screens, solders and capacitors. Lead damages the nervous system and in higher doses, causes lead poisoning. The relevant TCO'99 requirement permits the inclusion of lead since no replacement has yet been developed.

TCO'03-Ecological requirements for personal computers (TCO'03 applied model only)
Congratulations! The display you have just purchased carries the TCO'03 Displays label. This means that your display is designed, manufactured and tested according to some of the strictest quality and environmental requirements in the world. This makes for a high performance product, designed with the user in focus that also minimizes the impact on our natural environment. Some of the features of the TCO'03 Display requirements: Ergonomics Good visual ergonomics and image quality in order to improve the working environment for the user and to reduce sight and strain problems. Important parameters are luminance, contrast, resolution, reflectance, colour rendition and image stability. Energy Energy-saving mode after a certain time ?beneficial both for the user and the environment
Electrical safety Emissions Electromagnetic fields Noise emissions Ecology The product must be prepared for recycling and the manufacturer must have a certified environmental management system such as EMAS or ISO Restrictions on o chlorinated and brominated flame retardants and polymers o heavy metals such as cadmium, mercury and lead. The requirements included in this label have been developed by TCO Development in cooperation with scientists, experts, users as well as manufacturers all over the world. Since the end of the 1980s TCO has been involved in influencing the development of IT equipment in a more user-friendly direction. Our labelling system started with displays in 1992 and is now requested by users and IT-manufacturers all over the world. For more information, Please visit www.tcodevelopment.com
TCO'03 Recycling Information (TCO'03 applied model only) For recycling information for TCO'03 certified monitors, for the residents in the following countries, please contact the company corresponding to your region of residence. For those who reside in other countries, please contact a nearest local Samsung dealer for recycling information for the products to be treated in environmentally acceptable way.
[U.S.A. Residents Only] U.S.A. COMPANY Solid Waste Transfer & Recycling Inc 442 Frelinghuysen Ave Newark, NJ 07114 SWEDEN ELKRETSEN ELKRETSEN Box 1357, Stockholm Barnhusgatan 3, 4 tr. 08-90 08-99 [European Residents Only] NORWAY Elektronikkretur AS GERMANY vfw AG Max Plank Strasse Collogne Germany - 0

ADDRESS

6454 Etterstad 0602 Oslo Fyrstikkalln 3B 07 41
TELEPHONE 973-565-0181 FAX Fax: 973-565-9485 Enone MAIL http://www.bcua.org/Solid HOME Waste_Disposal.htm PAGE
info@el-kretsen.se adm@elektronikkretur.no
http://www.elkretsen.se/ http://www.elretur.no/

vfw.info@vfw-ag.de

Medical Requirement
Classifications: In accordance with UL 2601-1/IEC 60601-1, the product is cssified as Continuous duty Class I equipment, which is not protected against ingress of liquids. The product is not suitable for use in the presence of a flammable anaesthetic mixture with air or with oxygen or nitrous oxide. EMC This equipment has been tested and found to comply with the limits for medical devices to the IEC 601-1-2:1994. These limits are designed to provide reasonable protection against harmful
interference in a typical medical installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to other devices in the vicinity. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to other devices, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving device. Increase the separation between the equipment. Connect the equipment into an outlet on a circuit different from that to which the other device(s) are connected. Consult the manufacturer or field service technician for help. Video In / RS 232 / Video Out Accessories equipment connected to the analog and digital interfaces must be certified to the respective IEC standards (i.e. IEC 950 for data processing equipment and IEC 601-1 for medical equipment.) Furthermore all configurations shall comply with the system standard IEC 601-1-1. Everybody who connects additional equipment to the signal input part or signal output part configures a medical system, and is therefore, responsible that the system complies with the requirements of the system standard IEC 601-1-1. If in doubt, consult the technical services department or your local representative. Transport and Storage Limitations: Temperature Range of -40 C to +70 C Relative Humidity of 10 -95%, non-condensing * Bio-accumulative is defined as substances which accumulate within living organisms. ** Lead, Cadmium and Mercury are heavy metals which are Bio-accumulative.
Mercury Statement (LCD Monitor, LCD TV, DLP Projection TV, Projector for USA only) LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL, STATE OR FEDERAL LAWS For details see lamprecycle.org, eiae.org, or call 1-800-Samsung

PRODUCT INFORMATION (Image Retention Free)
LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. What is Image retention ? During normal operation of a LCD panel, pixel image retention doesn't occur. However, if the same image is displayed for a long time, a slight difference in electric charge accumulates between the two electrodes which encase the liquid crystal. This may cause the liquid crystal to build up in a certain areas of the display. Thus, the previous image is retained when switching to a new video image. All display products, including LCD,are subject to image retention. This is not a product defect. Please follow the suggestions below to protect your LCD from image retention Power Off, Screen Saver, or Power Save Mode Ex) Turn the power off when using a stationary pattern. - Turn the power off for 4 hours after 24 hours in use - Turn the power off for 2 hours after 12 hours in use Use a Screen saver if possible - Screen saver in one color or a moving image is recommended. Set the Monitor to power off with the PC Display Properties Power Scheme. Suggestions for specific applications Ex) Airports, Transit Stations, Stock Markets, Banks, and Controlling Systems We recommend that you follow set up of your display system program as below: Display Information together with Logo or Moving image cycle. Ex) Cycle : Display Information for 1 hour followed by a Display Logo or moving image for 1 minute. Change the Color Information periodically (Use 2 different colors). Ex) Rotate the Color Information with 2 colors every 30 minutes.
Avoid using a combination of characters and background color with large difference in luminance. Avoid using Grey colors, which can cause Image retention easily. Avoid: Colors with big difference in luminance (Black & White, Grey) Ex)