Do not remove cover(or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or a fire.
Do not place any heavy objects on the monitor. This may cause an electric shock or a fire.
For each hour of looking at the monitor, you should let your eyes rest for 5 minutes. This will reduce eye fatigue.
Do not use or store inflammable substances near the monitor. This may cause an explosion or fire.
Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.
Keep the monitor away from any magnetic substances. This may cause discoloring or distortion of the image.

Monitor and Stand

Power Cord
Quick Setup Guide (Some models include a stand attached. ) Please make sure the following items are included with your monitor. If any items are missing, contact your dealer. Warranty Card (Not available in all locations)
User's Guide and Driver Installation CD

For Multimedia model

Multimedia Speaker Stand Sound Cables(2each)

DC Power Cord (Option)

User Guide
1. Menu button 2. Adjust buttons 3. Enter button 4. Power button 5. Power indicator
Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. These buttons allow you to highlight and adjust items in the menu. Used to select the OSD menu. Use this button to turn the monitor on and off. This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
Note: See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.

General

SyncMaster 591S/793S/793DF/795DF /797DF/997DF/793MB/795MB
(The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal Cable Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the video port on your computer, video board, video card, or graphics card.

BNC Connectors (Option)

SyncMaster 997DF
(The configuration at the back of the monitor may vary from product to product.) 1. Power port 2. Signal port 3. BNC Connectors (Option) Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin D-sub connector on the back of your monitor. Connect the signal cable to the BNC signal port on the back of your monitor.
Note: See Connecting Your Monitor for further information regarding cable connections.
1. Signal Cable 2. Power port 3. Tilt/Swivel Base
Connect the signal cable to the video port on your computer, video board, video card, or graphics card. Connect the power cord for your monitor to the power port on the back of the monitor. You can separate the base from the monitor.
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the signal cable to the video port on your computer, video board, video card, or graphics card. 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4. Turn on your computer and monitor. If your monitor displays an image, installation is complete. BNC Connectors (Option)
1. Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2. Connect the end of the signal cable to your computer's video port(video board, video card or graphics card). 3. If you are using a Macintosh computer, connect the cable to a Macintosh adapter, and set the
pins on your adapter(Adapter not included). A PC-compatible computer does not need an adapter. 4. When you use a BNC connector. Connect the signal cable to the BNC signal port on the back of your monitor/computer. 5. Turn on your computer and monitor. If your monitor displays an image, installation is complete.
Opstilling-For multimedia-model
1. Sluk for computeren og fjern strmkablet. 2. Tilslut signalkablet til din computers videoport (videoboard, videokort eller grafikkort). 3. Tilslut den ene ende af et lydkabel til stereo output jacket p lydkort eller computer. Tilslut den anden ende af kablet til stereo input jacket bag p monitorens fod. Tilslut den ene ende af det andet lydkabel til linie output jacket p lydkort eller computer. Tilslut den anden af kablet til Mic By-Pass jacket bag p monitorens fod. 4. Tilslut DC strmkablet (jvnstrm) fra fodstykket til den nrmeste stikkontakt. 5. Tilslut monitorens strmkabel til strmporten bag p monitoren. 6. Tilslut monitorens strmkabel og computerens strmkabel til et stik i nrheden. 7. Tnd for computer og monitor. 8. Drej op eller ned p ON-OFF knappen p monitorens fod, indtil den klikker. 9. Start et lydprogram, musik eller lydeffekt p din computer og juster lydstyrken ved at skrue op eller ned til den nskede lydstyrke. 10. Juster diskant og bas. BEMRK: Lydforvrngning kan forekomme, hvis monitoren er placeret oven p et stort set hult kabinet, som f.eks. din computer. Hvis det sker, kan du anbringe en skriveblok eller et blad under monitorens fod. Hj lydstyrke kan ogs resultere i forvrngning af lyden; skru ned for lyden.

Fodstykke for Multimedia hjttaler
1. Mic by-pass jack For transmission af din stemme, tilslut et lydkabel fra mic by-pass jack til mic in jack p lydkortets slot i din computer. 2. Stereo input jack Tilslut et lydkabel fra input kilden (lydkort, computer, CD-ROM drev). 3. DC strmkabel Tilsluttes til monitorens DC 12V output jack. 4. Strmindikator Lyser grn, nr der er tndt for hjttalerne. 5. On/Off lydstyrke Tnder/slukker og justerer lydstyrken 6. Diskant kontrolknap Bruges til kontrol af hje frekvenser. 7. Bas kontrol knap Bruges til kontrol af lave frekvenser. 8. Mic input jack For transmission af din stemme, tilslut en mikrofon til dette jack. 9. Jack til retelefoner retelefoner kan tilsluttes her. 10. Aftagelig overdel til fodstykke.

Automatic

Manual
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (WorldWide) http://www.samsungusa.com/monitor/ (USA) http://www.sec.co.kr/monitor/ (Korea) http://www.samsungmonitor.com.cn/ (China)
1. Insert CD into the CD-ROM driver. 2. Click "Windows XP/2000 Driver". 3. Choose your monitor model in the model list, then click the "OK" button.
4. Click the "Install" button in the "Warning" window.
5. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
* This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 6. Monitor driver installation is completed.
Microsoft Windows XP Operating System 1. Insert CD into the CD-ROM driver. 2. Click "Start" > "Control Panel" then click the "Appearance and Themes" Icon.
3. Click "Display" icon and choose the "Settings" tab then click "Advanced.".
4. Click the "Properties" button on the "Monitor" tab and select "Driver" tab.
5. Click "Update Driver." and select "Install from a list or." then click "Next" button.
6. Select "Don't search ,I will." then click "Next" and then click "Have disk".
7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.

This monitor driver is under certifying MS logo,and this installation don't damage your system.The certified driver will be posted on Samsung Monitor Homepage http://www.samsung-monitor.com/. 9. Click the "Close" button then click "OK" button continually.
10. Monitor driver installation is completed.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button.
How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button. Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). Note: If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide. Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) 8. Set a vertical frequency for your monitor. (You can enter the frequency directly.) 9. Enter the model name of your monitor. This information will not affect the actual execution of X-Window. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. 1. 2. 3. 4. 5. 6. 7.

The image on the screen is shaking.
Check the monitor configuration to see if it is in Interlace Mode. (Interlace Mode: Vertical frequency 43Hz, 87Hz(i), etc) Are there any magnetic products such as a power adapter, speaker or a high voltage wire near by? Is the voltage stable?
The signal from the video card exceeds the maximum resolution and frequency of the monitor.
Move the monitor away from anything that can create a strong magnetic field.
The screen image can appear to shake or vibrate at a particular time of day due to low supply voltage.
The screen image can also appear to shake or vibrate if there is a problem with the video card or the computer's main board. The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly? The screen suddenly has become unbalanced. Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor? Check the signal cable connection. Make sure the video card is fully inserted in it's slot. Reboot the computer.
Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Display Modes).
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD.
The screen is out of focus or OSD cannot be adjusted. The screen is partially distorted.
Have you adjusted the resolution or frequency on the monitor? Are there any magnetic products such as an adapter, speaker or a high voltage wire near the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu?
Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). Enter the OSD and perform a "Degauss". Keep the monitor away from any magnetic products. Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product.)

LED is blinking but no images on the screen.
There are only 16 colors shown on the screen. The screen colors have changed after changing the video card.
Have the Windows colors been set properly? Has the video card been set properly?
For Windows XP/ 2000: Set the colors properly at the Control Panel, Display, Settings. Set the video card by referring to the video card manual.
Check the following items if there is trouble with the monitor. 1. Check if the power cord and the cable are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter (video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz or 85Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control Panel, System, Device Administrator" and then reboot the computer to reinstall the adapter (video) driver. Note: If problems repeatedly occur, contact an authorized service center.
Question How can I change the frequency?
Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.)
How can I adjust the resolution?
Windows XP/2000: Set the resolution at the Control Panel, Display, Settings. * Contact the video card manufacturer for details.
How can I set the Power Saving function?
Windows XP/2000: Set the function at BIOS -SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual). This is normal as some sound may be generated when the metal case and the electromagnet, which are installed to block any electromagnetic waves, interact with each other. Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.
The monitor makes a sound when it is turned on.
How can I clean the outer case/Picture tube?
SyncMaster 591S/793S/793DF/795DF/797DF/793MB/795MB
Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly.
1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If your monitor works normally, the following screen appears.
SyncMaster 591S/793DF/795DF
Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.

PowerSaver

Preset Timing Modes
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 90W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2.0W
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.
If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows.

General PowerSaver

Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 1024 x 768 VESA, 1280 x 1024 Horizontal Frequency (kHz) 37.500 68.677 91.146 Vertical Frequency (Hz) 75.000 84.997 85.024 Pixel Clock (MHz) 31.500 94.500 157.50 Sync Polarity (H/V) -/+/+ +/+
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Vertical Frequency Like a fluorescent lamp, the screen has to repeat the same image many times per second to display an image to the user. The frequency of this repetition is called Vertical Frequency or Refresh Rate. Unit: Hz

SyncMaster 795DF/795MB

Maximum Resolution 1600 x 1200 (NI) Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 185 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 90W Dimensions (WxDxH) 401 x 410 x 378mm (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 85 kHz 50 ~ 160 Hz mm mm

Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 1024 x 768 VESA, 1280 x 1024 Horizontal Frequency (kHz) 37.500 68.677 79.976 Vertical Frequency (Hz) 75.000 84.997 75.025 Pixel Clock (MHz) 31.500 94.500 135.00 Sync Polarity (H/V) -/+/+ +/+

SyncMaster 793S

Picture Tube Type Deflection angle Dot Pitch Screen type 17"(43cm) Full square type (40.6cm viewable) 90 0.23mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static.
Maximum Resolution 1280 x 1024 (NI) Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 110 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 90W Dimensions (WxDxH) 401 x 410 x 378mm (After installation of Stand) Weight 14.3kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 70 kHz 50 ~ 160 Hz mm mm
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 90W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2W

Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 800 x 600 VESA, 1024 x 768 Horizontal Frequency (kHz) 37.500 53.674 68.677 Vertical Frequency (Hz) 75.000 85.061 84.997 Pixel Clock (MHz) 31.500 56.250 94.500 Sync Polarity (H/V) -/+/+ +/+

SyncMaster 793DF/793MB

SyncMaster 591S
Picture Tube Type Deflection angle Dot Pitch Screen type 15" (38cm) Full square type (35cm viewable) 90 0.24mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.
Maximum Resolution 1024 x 768(NI) Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 65 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 70W Dimensions (WxDxH) 361 x 379.2 x 347 mm (After installation of Stand) Weight 11.0 kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 - 55 kHz 50 ~ 120 Hz mm mm
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 70W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2.0W
Table 1. Preset Timing Modes Display Mode VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 Horizontal Frequency (kHz) 37.500 43.269 53.674 Vertical Frequency (Hz) 85.008 75.000 85.061 Pixel Clock (MHz) 36.000 31.500 56.250 Sync Polarity (H/V) -/-/+/+
Picture Tube Type Deflection angle Dot Pitch Screen type 19"(48cm) DynaFlat (45.8cm viewable) 90 0.20mm (Horizontal) Aluminized tri-color phosphor dot trio with black matrix. Anti-doming invar shadow mask. Multi-layer coated with anti-static/Glare.

Maximum Resolution 1600 X 1200@ 76Hz Active Display Horizontal Vertical Synchronization Horizontal Vertical Input Signal Definition Video Signal Sync Signal Display Color Unlimited Maximum Pixel Clock 250 MHz Power Supply 90 ~ 264VAC rms, 60/50 Hz 3Hz Power Consumption Less than 110W Dimensions (WxDxH) 445 x 457,5 x 416mm (After installation of Stand) Weight 18,2 kg Environmental considerations Operating Temperature 32F ~ 104F(0C ~ 40C) Humidity 10% ~ 80%, non-condensing Storage Temperature -4F ~113F (-20C ~ 45C) Humidity 5% ~ 95%, non-condensing Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Note: Design and specifications are subject to change without prior notice. RGB, Analog 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level, positive or negative 30 ~ 96 kHz 50 ~ 160 Hz mm mm
This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you move the computer's mouse or press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 110W Power-off Mode EPA/ENERGY 2000 Green, Blinking Less than 2W
AUSTRALIA : Samsung Electronics Australia Pty Ltd. Customer Response Centre 7 Parkview Drive, Homebush Bay NSW 2127 Tel : 603 http://www.samsung.com.au/ BRAZIL : Samsung Eletronica da Amazonia Ltda. R. Prof. Manoelito de Ornellas, 303, Terro B Chacara Sto. Antonio, CEP : 04719-040 Sao Paulo, SP SAC : 421 http://www.samsung.com.br/ CANADA : Samsung Electronics Canada Inc. Samsung Customer Care 7037 Financial Drive Mississauga, Ontario L5N 6R3 1-800-SAMSUNG (1-800-726-7864) http://www.samsung.ca/ CHILE : SONDA S.A. Teatinos 550, Santiago Centro, Santiago, Chile Fono: 56-2-5605000 Fax: 56-2-5605353 56-2-800200211 http://www.sonda.com/ http://www.samsung.cl/ COLOMBIA : Samsung Electronics Colombia Cra 9 No 99A-02 Of. 106 Bogota, Colombia Tel.: 9-800-112-112 Fax: (571) 618 - 2068 http://www.samsung-latin.com/ e-mail : soporte@samsung-latin.com ESPAA : Samsung Electronics Comercial Iberica, S.A. Ciencies, 55-65 (Poligono Pedrosa) 08908 Hospitalet de Llobregat (Barcelona) Tel. : (93) 00 Fax. : (93) 50 http://samsung.es/ FRANCE : SAMSUNG ELECTRONICS FRANCE Service Paris Nord rue des Vanesses BP 50116 Villepinte 95950 Roissy CDG Cedex Tel : 65 Fax : 38 http://www.samsungservices.com/ GERMANY : TELEPLAN Rhein-Main GmbH Feldstr. Weiterstadt T. 06151/957-1306 F. 06151/957-1732 * EURO 0.12/Min http://www.samsung.de/ HUNGARY : Samsung Electronics Magyar Rt. 1039, Budapest, Lehel u. 15-17. Tel: Fax: http://www.samsung.hu/

Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz. In this case, flickering of the screen can be detected. To avoid this problem, there is a Flicker-free Mode using a vertical frequency over 70 Hz. Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1024 X 768, this means the screen is composed of 1024 horizontal dots (horizontal resolution) and 768 vertical lines (vertical resolution).
Natural Color Software Program
One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. The Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI). This system is available only for Samsung monitors and makes the color of the images on the monitor the same as the printed or scanned images. For more information, refer to Help (F1) in the software program. How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program installation will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CD-ROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup.exe and then press the key. (If the drive where the CD is inserted is not D:\, enter the applicable drive.) How to delete the Natural Color software program Select [Setting]/[Control Panel] on the [Start] menu and then double-click [Add/Delete a program]. Select Natural Color from the list and then click the [Add/Delete] button.

Information in this document is subject to change without notice. 2004 Samsung Electronics Co., Ltd. All rights reserved. Reproduction in any manner whatsoever without the written permission of Samsung Electronics Co., Ltd. is strictly forbidden. Samsung Electronics Co., Ltd. shall not be liable for errors contained herein or for incidental or consequential damages in connection with the furnishing, performance, or use of this material. Samsung is the registered trademark of Samsung Electronics Co., Ltd.; Microsoft, Windows and Windows NT are registered trademarks of Microsoft Corporation; VESA, DPMS and DDC are registered trademarks of Video Electronics Standard Association; the ENERGY STAR name and logo are registered trademarks of the U.S. Environmental Protection Agency (EPA). As an ENERGY S TAR Partner, Samsung Electronics Co., Ltd. has determined that this product meets the ENERGY S TAR guidelines for energy efficiency. All other product names mentioned herein may be the trademarks or registered trademarks of their respective owners.