Washing Machine Owners Instructions
B1445(V/S/C) B1245(V/S/C) B1045(V/S/C) F1245(V/S/C) F1045(V/S/C)
Register your product at www.samsung.com/global/register

Code No.: DC68-02110M-EN

Safety Precautions
Congratulations on your purchase of this Samsung washing machine. These Owner's Instructions contain valuable information on the installation, use, and care of this appliance. Please take the time to read these instructions so that you can take full advantage of the washing machine's features and enjoy this appliance for many years to come.
Before using the appliance
Packing materials can be dangerous to children; keep all packing material (plastic bags, polystyrene, etc.) well out of the reach of children. The appliance is designed for home use only. Make sure that water and electrical connections are made by qualified technicians, observing the manufacturer's instructions (see "Installing the Washing Machine") and local safety regulations. All packaging and shipping bolts must be removed before the appliance is used. Serious damage may occur if they are not removed. See "Removing the shipping bolts". Before washing clothes for the first time, you must run a complete cycle without clothes. See "Washing for the first time".

Safety instructions

Before cleaning or carrying out maintenance, unplug the appliance from the electrical outlet or set the (On/Off) button to Off. Make sure that the pockets of all clothing to be washed are empty. Hard, sharp objects, such as coins, safety pins, nails, screws, or stones can cause extensive damage to the appliance. Always unplug the appliance and turn off the water after use. Before you open the door of the appliance, check that the water has drained. Do not open the door if you can still see water. Pets and small children may climb into the appliance. Check the appliance before each use. The glass door becomes very hot during the washing cycle. Keep children away from the appliance while it is in use. Do not attempt to repair the appliance yourself. Repairs made by inexperienced or unqualified persons may cause injury and/or make more serious repairs to the appliance necessary. If the plug (power supply cord) is damaged, it must be replaced by the manufacturer or its service agent or a similarly qualified person in order to avoid a hazard. This appliance should only be serviced by an authorized service center, and only genuine spare parts should be used. This appliance is not intended for use by young children or infirm persons unless they have been adequately supervised by a responsible person to ensure that they can use the appliance safely. Young children should be supervised to ensure that they do not play with the appliance. If this appliance is supplied from a cord extension set or an electrical portable outlet device, the cord extension set or electrical portable outlet device must be positioned so that it is not subject to splashing or ingress of moisture. Additionally, the cord extension set or electrical portable out let device must be of a current rating suitable for the appliance. This appliance has to be connected to the plug endurable to proper power consumption. This appliance has to be positioned so that the plug is accessible after installation. Do not use processed water containing oil, cream or lotion, which is usually found in skin-care shops or massage clinics. Otherwise this will cause the packing to be deformed, which causes a malfunction or water leak. A stainless washing tube does not usually rust. However if some metal such as a hair pin is left in the tube for an extended time, the tube could rust. Do not leave water or bleach containing chlorine in the tube for an extended period of time. Do not regularly use or leave water containing iron in the tube for an extended period of time. If rust starts appearing on the surface of the tube, apply a cleansing agent (neutral) to the surface and use a sponge or soft cloth to clean it. (Under no circumstances use a metal brush)

Maintaining the Washing Machine --------------------------------- 12
Draining the washing machine in an emergency ----------------------------- 12 Repairing a frozen washing machine -------------------------------------------- 12 Cleaning the exterior ---------------------------------------------------------------- 12 Cleaning the detergent drawer and recess ----------------------------------- 13 Cleaning the debris filter ------------------------------------------------------------ 13 Cleaning the water hose mesh filter --------------------------------------------- 14
Troubleshooting ----------------------------------------------------------------- 15
Problems and solutions ------------------------------------------------------------ 15 Understanding error messages --------------------------------------------------- 15
Programme chart ------------------------------------------------------------- 16 Appendix ------------------------------------------------------------------------------ 18
Fabric care chart --------------------------------------------------------------------- 18 Electrical warnings ------------------------------------------------------------------ 18 Protecting the environment ------------------------------------------------------- 19 Declaration of conformity --------------------------------------------------------- 19 Specification -------------------------------------------------------------------------- 19
SAMSUNG Washing Machine Owners Instructions 1
Installing the Washing Machine
Unpacking the Washing Machine
Unpack your washing machine and inspect it for shipping damage. Also make sure that you have received all of the items shown below. If the washing machine was damaged during shipping or you do not have all of the items, contact your Samsung dealer immediately.
Overview of the washing machine

Worktop

Detergent drawer Control panel Door

Drain Hose

Base cover Adjustable feet

Debris filter

Emergency drain tube Filter-cover
Cold Water supply hose Wrench Drain hose * (Option) Hot Water supply hose

Hose guide

Bolt hole covers
2 SAMSUNG Washing Machine Owners Instructions

Selecting a location

Before you install the washing machine, select a location with the following characteristics: A hard, level surface (if the surface is uneven, see "Adjusting the leveling feet," below) Away from direct sunlight. Adequate ventilation Room temperature that will not fall below 0 C Away from sources of heat such as coal or gas Make sure that the washing machine does not stand on its power cord. Ventilation openings must not be obstructed by carpeting when the washing machine is installed on a carpeted floor.
Adjusting the leveling feet
If the floor is uneven, adjust the feet (do not insert pieces of wood or any other objects under the feet): 1. Loosen the leg bolt by turning it with your hand until it is at the desired height. 2. Tighten the locking nut by turning it with the supplied wrench.
Place the washer on a sturdy, flat surface. If the washer is placed on an uneven or weak surface, noise or vibration occurs. (Only a l degrees angle is allowed.)
Removing the shipping bolts
Before using the washing machine, you must remove the five shipping bolts from the back of the unit. To remove the bolts:
1. Loosen all bolts with the supplied wrench before removing them. 2. Take each bolt head and pull it through the wide part of the hole. Repeat for each bolt. 3. Fill the holes with the supplied plastic covers. 4. Keep the shipping bolts for future use.
Connecting the water supply hose(Option)
1. Remove the adaptor from the water supply hose.
4. Connect the water supply hose to the adaptor. Pull down part (c) of the water supply hose. When you release part (c) the hose automatically connects to the adaptor making a click sound. 5. Connect the other end of the water supply hose to the inlet water valve at the top of the washer. Screw the hose clockwise all the way in.
2. First, using a + type screw driver, loosen the four screws on the adaptor. Next, take the adaptor and turn part(b) following the arrow until there is a 5mm gap. 3. Connect adaptor to the water tap by tightening the screws firmly. Then, turn part (b) following the arrow and put(a) and (b) together.
If the water tap has a screw type faucet, connect
the water supply hose to the tap as shown.
NOTICE After completing connection, if water leaks from the hose, then repeat the same steps. Use
the most conventional type of faucet for water supply. In case the faucet is square or too big, remove the spacing ring before inserting the faucet into the adaptor.
SAMSUNG Washing Machine Owners Instructions 3
Connecting the water supply hose
The water supply hose must be connected to the washing machine at one end and to the water faucet at the other. Do not stretch the water supply hose. If the hose is too short and you do not wish to move the water faucet, replace the hose with a longer, high pressure hose. To connect the water supply hose: 1. Take the L-shaped arm fitting for the cold water supply hose and connect to the cold water supply intake on the back of the machine. Tighten by hand.

2. Connect the other end of the cold water supply hose to your sink's cold water faucet and tighten it by hand. If necessary, you can reposition the water supply hose at the washing machine end by loosening the fitting, rotating the hose, and retightening the fitting. Option: 1. Take the red L-shaped arm fitting for the hot water supply hose and connect to the red hot water supply intake on the back of the machine. Tighten by hand. 2. Connect the other end of the hot water supply hose to your sink's hot water faucet and tighten it by hand. 3. Use a Y-piece if you only want to use cold water. Note: The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be used.
Positioning the drain hose
The end of the drain hose may be positioned in three ways:

Over the edge of a sink

The drain hose must be placed at a height of between 60 and 90 cm. To keep the drain hose spout bent, use the supplied plastic hose guide. Secure the guide to the wall with a hook or to the faucet with a piece of string to prevent the drain hose from moving.
ln a sink drain pipe branch
The drain pipe branch must be above the sink siphon so that the end of the hose is at least 60 cm above the ground.

ln a drain pipe

Samsung recommends that you use a 65 cm high vertical pipe; it must be no shorter than 60 cm and no longer than 90 cm.
4 SAMSUNG Washing Machine Owners Instructions

Plugging in the machine

For European Users. You will NOT need to ground the plug of the washing machine. For U.S. Users. You MUST ground the plug of the washing machine.
Check with a licensed electrician before using the machine to make sure it is properly grounded.

For U.K. Users.

Wiring lnstructions
WARNING THIS APPLIANCE MUST BE EARTHED.
This appliance must be earthed. In the event of an GREEN AND electrical short circuit, earthing reduces the risk of electric YELLOW shock providing an escape wire for the electric current. The appliance is equipped with a mains lead which includes an earth wire for connecting to the earth terminal of your mains plug. The plug must be plugged into a socket that is properly installed and earthed. *The wires in this mains lead are coloured in accordance with the following code: Green and yellow : Earth : Neutral Blue Brown : Live AS the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings indentifying the terminals in your plug, proceed as follows. Connect the green and yellow wire to the terminal in the plug marked with the letter E or the earth symbol ( ) or coloured green or green-andyellow. Connect the blue wire to the terminal marked with the letter N or coloured black. Connect the brown wire to the terminal marked with the letter L or coloured red. * Consult a qualified electrician or service technician if in doubt about any of these instructions. The manufacturer of this washing machine will not accept any liability for damage to persons or material for non observance of these requirements. There are no user serviceable parts inside the washing machine and if the mains lead of this appliance is damaged, it must only be replaced by qualified service personnel approved by the manufacturer because special tools are required.

13 AMP FUSE

BLUE WARNING
Ensure that the plug and power cord are not damaged before use. If you have any reason to remove the moulded plug from this appliance, immediately remove the fuse and dispose of the plug. Do not connect the plug to a mains socket under any circumstances as there is a danger of electric shock.

CIRCUITS

Your washing machine should be operated on a separate circuit from other appliances. Failure to do this may cause the circuit breaker to trip or the fuse to blow.
SAMSUNG Washing Machine Owners Instructions 5
Washing a Load of Laundry
Overview of the control panel
This is a general manual. The INLAY system may be different from that of the product you purchased. For A , see item 5 below to select the right specifications that match your product.
1. Digital graphic display
Displays the remaining wash cycle time,all of washing information and error messages.

Prewash selection button

Press the button to select pre-wash. Pre-wash is available only with Cotton, Coloureds, Synthetics, Delicates,baby programs.
Temperature selection button
Press the button repeatedly to cycle through the available water temperature options (cold water( ), 30 C, 40 C , 60 C and 95 C).

Rinse selection button

Press the rinse button to add rinse cycles. Maximum number of rinse cycles is five.

Spin selection button

Press the button repeatedly to cycle through the available spin speed options. B1445 , , 400, 800, 1200, 1400 rpm B1245/F1245 , , 400, 800, 1000, 1200 rpm B1045/F1045 , , 400, 600, 800, 1000 rpm : no spin, : rinse hold
No spin The laundry remains in the drum without being spun after the final drain Rinse Hold The laundry remains soaking in the final rinse water. Before the laundry can be unloaded, either Drain or the Spin program must be run.
6 SAMSUNG Washing Machine Owners Instructions
Delay Start selection button
Press the button repeatedly to cycle through the available delayed start options (from 3 hour to 24 hours in one hour increments). Displayed hours means the time of finished washing-cycle.
Half Load selection button
Press the button in case of half load(about 1~4kg) washing. This function saves washing time and energy.
Child Lock selection button
Press the delay start and half load button simultaneously for 2~3 seconds to prevent misoperation by a child. When the Child Lock is on, other buttons can not be selected. To cancel the Child Lock, press the Child Lock button simultaneously for 2~3 seconds.

9. Fuzzy Control dial

Turn the dial to select one of the 14 available wash programs. Cotton, Coloureds, Synthetics, Quick, Rinse+Spin, Spin, Delicates, Coloreds, Cotton) Delicates, Wool, Hand wash, Drain, Baby Program( Stains,

10. 11.

Start/Pause selection button (On/Off) selection button

Press to pause and restart programs.
Press once to turn the washing machine on, press again to turn the washing machine off. If the washing machine power is left on for longer than 10 minutes without any buttons being touched, the power automatically turns off.
SAMSUNG Washing Machine Owners Instructions 7
Washing for the first time
Before washing clothes for the first time, you must run a complete cycle without clothes. To do this: 1. Press the (On/Off) button. 2. Pour a little detergent into compartment in the detergent drawer. 3. Turn on the water supply to the washing machine. 4. Press the Temperature button repeatedly until 40 C is displayed. 5. Press the Start/Pause button. This will remove any water from the manufacturers test run remaining in the machine.
Dispender Dispenser Dispenser :Detergent for prewash or starch. : Detergent for main wash, water softener,pre-soaking agent, bleach and stain removal product. : Additives,e.g.fabric softener or former (fill no higher than lower edge of insert A)
Putting detergent in the washing machine
1. Pull out the detergent drawer. 2. Add laundry detergent into compartment. 3. Add softener into compartment (if you desire). 4. Add prewash detergent into compartment (if you desire).
Caution : Concentrated or thick fabric softener and conditioner must be diluted with a little water before being poured into the dispenser (prevents the overflow from becoming blocked.)
8 SAMSUNG Washing Machine Owners Instructions
Washing clothes using Fuzzy Logic
Your new washing machine makes washing clothes easy, using Samsung's "Fuzzy Logic" automatic control system. When you select a wash program, the machine will set the correct temperature, washing time, and washing speed. To wash clothes using the Fuzzy Logic programs: 1. Turn on your sink's water faucet. 2. Press the (On/Off) button. 3. Open the door. 4. Load the articles one at a time loosely into the drum, without overfilling. 5. Close the door. 6. Add the detergent, softener, and pre-wash detergent (if necessary) into the appropriate compartment. Note: Pre-wash is only available when washing Duvet, Bedding, Towel, Curtain, Cotton, Coloureds, Synthetics and Delicates programs. It is only necessary if your clothing is heavily soiled. 7. Turn the Fuzzy Control dial to select the appropriate program for the type of clothes Cotton, Coloureds, Synthetics, Delicates, Wool, Hand wash, Quick, Rinse+Spin, Spin, Drain, Baby Program(Stains, Delicates, Coloreds, Cotton) You will see the indicators light up on the control panel.

8. At this time, you can control the wash temperature, rinsing times, spin speed, delay time by pressing the appropriate option button. 9. Press the Start/Pause button on the Fuzzy Control dial and the wash cycle will begin. The process indicator will light up and the remaining time for the cycle will appear in the display.
When the cycle is finished:
After the total cycle has finished, the power will turn off automatically. 1. Open the door. Note: The door will not open untill 3 minutes after the machine stops or the power turns off. 2. Remove laundry.
SAMSUNG Washing Machine Owners Instructions 9

Washing clothes manually

You can wash clothes manually without using the Fuzzy Logic feature. To do so: 1. Turn the water supply on. 2. Press the (On/Off) button on the washing machine. 3. Open the door. 4. Load the articles one at a time loosely into the drum, without overfilling. 5. Close the door. 6. Put the detergent and, if necessary, softener or prewash detergent, in the appropriate compartments. 7. Press the Temperature button to select the temperature (cold water, 30C, 40C, 60C, 95C) 8. Press to rinse button to select the required number of rinse cycles. Maximum number of rinse cycles is five. The washing duration will be prolonged accordingly. 9. Press the Spin button to select the spin speed. Note: The rinse hold program allows you to take clothes that are dripping wet out of the washing machine. : No Spin, : Rinse Hold. 10. Press the button repeatedly to cycle through the available delayed start options (from 3 hour to 24 hours in one hour increments). Displayed hours means the time of finished washing-cycle. 11. Press the Start/Pause button and the machine will begin the cycle.

Using Delay Start

You can set the washing machine to finish your wash automatically at a later time, choosing from 3 to 24 hour delay (in 1 hour increments). Displayed hours means the time of finished washing-cycle. To do this: 1. Manually or automatically set your washing machine for the type of clothes you are washing. 2. Press the Delay Start button repeatedly until the delay time is set. 3. Press the Start/Pause button. The Delay Start indicator will light, and the clock will begin counting down until it reaches your finish time. 4. To cancel Delay Start, press the (On/Off) button, then turn the washing machine on again.

10 SAMSUNG Washing Machine Owners Instructions

Washing tips and hints

Sorting your laundry : Sort your laundry according to the following characteristics:
Type of fabric care label symbol : Sort laundry into cottons, mixed fibers, synthetics, silks, wools and rayon. Colour : Divide whites and colours. Wash new, coloured items separately. Size: Placing items of different sizes in the same load will improve the washing action. Sensitivity: Wash delicate items separately, using the Delicate wash program for pure new wool, curtains and silk articles. Check the labels on the items you are washing or refer to the fabric care chart in the appendix.
Emptying pockets : Coins, safety pins and similar items can damage linen, the washing
machine drum, and the water tank.
Securing fasteners : Close zippers and fasten buttons or hooks; loose belts or ribbons

should be tied together.

Prewashing cotton : Your new washing machine, combined with modern detergents,
will give perfect washing results, thus saving energy, time, water and detergent. However, if your cotton is particularly dirty, use a prewash with a protein-based detergent.
Determining load capacity: Do not overload the washing machine or your laundry
may not wash properly. Use the chart below to determine the load capacity for the type of laundry you are washing. Fabric Type Load Capacity B1445/B1245/B1045 Coloured/cotton -average/lightly soiled -heavily soiled Synthetics Delicates Wools 6.0 kg 6.0 kg 3.0 kg 2.5 kg 2.0 kg F1245/F1045 4.5 kg 4.5 kg 3.0 kg 2.0 kg 1.5 kg
Detergent tips: The type of detergent you should use is based on the type of fabric (cotton, synthetic, delicate items, wool), colour, wash temperature, degree and type of soiling. Always use "low suds" laundry soap, which is designed for automatic washing machines.
Follow the detergent manufacturer's recommendations based upon the weight of the laundry, the degree of soiling, and the hardness of the water in your area. If you do not know how hard your water is, ask your water authority. Note: Keep detergents and additives in a safe, dry place out of the reach of children.
SAMSUNG Washing Machine Owners Instructions 11
Maintaining the Washing Machine
Draining the washing machine in an emergency

B1445/ B1245/ B1045

1. Unplug the washing machine
2. from the power supply. Open the filter-cover by using a coin or a key.
Unscrew the emergency drain cap by turning left. Grip the cap on the end of the emergency drain tube and slowly pull it out about 15 cm.

4. 5. 6.

Allow all the water to flow into a bowl. Reinsert the drain tube and screw the cap back on. Replace the filter-cover.
Repairing a frozen washing machine
If the temperature drops below freezing and your washing machine is frozen: 1. Unplug the washing machine. 2. Pour warm water on the source faucet to loosen the water supply hose. 3. Remove the water supply hose and soak it in warm water. 4. Pour warm water into the washing machine drum and let it sit for 10 minutes. 5. Reconnect the water supply hose to the water faucet and check if the water supply and drain operations are normal.

Cleaning the exterior

1. 2. 3. Wipe the washing machine surfaces, including the control panel, with a soft cloth and non-abrasive household detergents. Use a soft cloth to dry the surfaces. Do not pour water on the washing machine.
12 SAMSUNG Washing Machine Owners Instructions
Cleaning the detergent drawer and recess
1. Press the release lever on the inside of the detergent drawer and pull it out. 2. Remove the cap from compartment. 3. Wash all of the parts under running water. 4. Clean the drawer recess with an old toothbrush. 5. Reinsert the cap (Pushing it firmly into place) and replace the liquid detergent divider into the drawer. 6. Push the drawer back into place. 7. Run a rinse program without any laundry in the drum.
Cleaning the debris filter
Clean the debris filter 5 or 6 times a year, or when you see the following error message on the display:
1. Open the filter-cover, See Draining the washing machine in an emergency" on page 12. 2. Unscrew emergency drain cap by turning left and drain off all the water. See "Draining the washing machine in an emergency" on page 12. 3. Unscrew the filter cap and take it out.
4. Wash any dirt or other material from the filter. Make sure the drain pump propeller behind the filter is not blocked. Replace the filter cap. 5. Replace the filter-cover.
SAMSUNG Washing Machine Owners Instructions 13
Cleaning the water hose mesh filter
You should clean the water hose mesh filter at least one time per year, or when you see the following error message on the display:
To do this: 1. Turn off the water source to the washing machine. 2. Unscrew the hose from the back of the washing machine. 3. With a pair of pliers, gently pull out the mesh filter from the end of the hose and rinse it under water until clean. Also clean the inside and outside of the threaded connector.
4. Push the filter back into place. 5. Screw the hose back onto the washing machine. 6. Turn on the faucet and make sure the connections are watertight.
14 SAMSUNG Washing Machine Owners Instructions

Troubleshooting

Problems and solutions
The washing machine will not start
Make sure the door is firmly closed. Make sure the washing machine is plugged in. Make sure the water source faucet is turned on. Make sure to press the Start/Pause button. Make sure the water source faucet is turned on. Make sure the water source hose is not frozen. Make sure the water intake hose is not bent. Make sure the filter on the water intake hose is not clogged.

No water or insufficient water supply
Detergent remains in the detergent drawer after the wash program is complete
Make sure the washing machine is running with sufficient water pressure. Put the detergents in the inner parts of the detergent drawer(away from the outside edges). Make sure the washing machine is set on a level surface. If the surface is not level, adjust the washing machine feet to level the appliance. Make sure that the shipping bolts are removed. Make sure the washing machine is not touching any other object. Make sure the laundry load is balanced. Make sure the drain hose is not squashed or bent. Make sure the debris filter is not clogged.
Washing machine vibrates or is too noisy
The washing machine does not drain and/or spin

The Door does not open

The door will not open until 3 minutes after the machine stops or the power turns off.
Understanding error messages

Error displayed Solution

Close the door. Make sure the source water faucet is turned on. Check the water pressure. Clean the debris filter. Make sure the drainage hose is installed correctly. Laundry load is unbalanced; loosen any tangled laundry. If only one item of clothing needs washing, such as a bathrobe or jeans, the final spin result might be unsatisfactory and an "UE" error message will be shown in the display window. Call after-sales service. Before contacting After-Sales service: 1. Try to remedy the problem (See "Troubleshooting" on this page). 2. Restart the programme to see if the fault is repeated. 3. If the malfunction persists, call after-sales service and describe the problem.
SAMSUNG Washing Machine Owners Instructions 15

Programme Chart

( user option)
Max load (kg) PROGRAM Cotton Coloureds Synthetics Delicates Wool Handwash Quick
B1445 B1245 B1045 F1245 F1045 DETERGENT Tem AND ADDITIVES (C) PreSofwash Max wash tener

Spin Speed(MAX)rpm

B1445 B1245 F1245 B1045 F1045 Delay Half start Load
6.0 6.0 3.0 2.5 2.0 2.0 2.0
4.5 4.5 3.0 2.0 1.5 1.5 1.5
yes yes yes yes yes yes yes
PROGRAM Cotton Coloureds Synthetics Delicates Wool Handwash Quick
Type of WASH Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels, shirts, etc. Averagely or lightly soiled cottons, bed linen, table linen, underwear, towels, shirts, etc. Averagely or lightly soiled blouses, shirts, etc., Made of polyester (diolen, trevira), polyamide (perlon, nylon) or other similar blends. Delicate curtains, dresses, skirts, shirts and blouses. Only machine washable woolens with pure new wool label. Very light wash course like hand wash. Lightly soiled cottons or linen blouses, shirts, dark coloured terry cloth, coloured linen articles, jeans, etc.

1. Programme with prewash lasts approx. 15 minutes longer. 2. The programme duration data has been measured under the conditions specified in Standard IEC 456. 3. Consumption in individual homes may differ from the values given in the table due to variations in the pressure and temperature of the water supply, the load and the type of laundry.
16 SAMSUNG Washing Machine Owners Instructions
Max load (kg) PROGRAM Baby Cotton
Baby Coloureds Baby Delicates B1445 B1245 B1045 F1245 F1045 DETERGENT Tem AND ADDITIVES (C) PreSofwash Max wash tener

6.0 6.0

4.5 4.5

yes yes

1400 1400

1200 1200

1000 1000

2.5 6.0

2.0 4.5

800 1400

800 1200

800 1000

Baby Stains

PROGRAM Baby Cotton

Type of WASH Averagely or lightly soiled baby cottons, bed linen, table linen, underwear, towels, shirts, etc.
Baby Coloureds Averagely or lightly soiled baby cottons, bed linen, table linen, underwear, towels, shirts, etc. Baby Delicates Baby Stains Delicate baby dresses, skirts, shirts and blouses. Stains on cottons, bed lined, underwear, towels, etc. caused by food spills and urine.
SAMSUNG Washing Machine Owners Instructions 17

Appendix

Fabric care chart
Resistant material Delicate fabric Item may be washed at 95 C Item may be washed at 60 C Item may be washed at 40 C Item may be washed at 30 C Item may be hand washed Dry flat Dry clean only Can be hung to dry Can be bleached in cold water Dry on clothes hanger Do not bleach Tumble dry, normal heat Can be ironed at 200 C max Tumble dry, reduced heat Do not tumble dry Can be ironed at 100 C max Do not iron Can be dry cleaned using any solvent Dry clean with perchloride, lighter fuel, pure alcohol or R113 only Dry clean with aviation fuel, pure alcohol or R113 only Do not dry clean
Can be ironed at 150 C max

Electrical warnings

To reduce the risk of fire, electrical shock, and other injuries, keep these safety precautions in mind: Operate the appliance only from the type of power source indicated on the marking label. If you are not sure of the type of power supplied to your home, consult your appliance dealer or local power company. Use only a grounded or polarized outlet. For your safety, this appliance is equipped with a polarized alternating current line plug having one blade wider than the other. This plug will fit into the power outlet only one way. If you are unable to insert the plug fully into the outlet, try reversing the plug. If the plug still doesn't fit, contact your electrician to replace your outlet. Protect the power cord. Power supply cords should be routed so that they are unlikely to be walked on or pinched by items placed on or against them. Pay particular attention to cords at plugs, convenience receptacles, and the point where they exit from the unit. Do not overload the wall outlet or extension cords. Overloading can result in fire or electric shock.

18 SAMSUNG Washing Machine Owners Instructions
Protecting the environment
This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source. Remove the door so that animals and small children cannot get trapped inside the appliance. Do not exceed the detergent quantities recommended in the detergent manufacturers' instructions. Use stain removal products and bleaches before the wash cycle only when strictly necessary. Save water and electricity by only washing full loads (the exact amount depends upon the program used).
Declaration of conformity
This appliance complies with European safety standards, EC directive 93/68 and EN Standard 60335.

Specification

DIMENSION WATER PRESSUERE WATER VOLUME NET WEIGHT WASH and SPIN CAPACITY MODEL POWER CONSUMPTION 54L 75kg 6.0kg (DRY LAUNDRY) B1445/B1245/B1045

FRONT LOADING WASHER

B1445/B1245/B1045 W598mm D550mm H844mm 50 kPa ~ 800 kPa 48L 62kg 4.5kg (DRY LAUNDRY) F1245/F1045 1800W 2100W F1045 220W F1245/F1045 W598mm D404mm H844mm
WASH and 220V HEATING 240V MODEL B1445 SPIN 230V 550W PUMPING MODEL
2000W 220V 2400W 240V B1245 B1045 F1245 550W 500W 250W 34W
B1445/B1245/B1045 2.5kg 1.0kg BB1245/F1245 1200
F1245/F1045 1.9kg 0.8kg B1045/F1045 1000

PACKAGE Wt

PAPER PLASTIC MODEL rpm

SPIN REVOLUTION

SAMSUNG Washing Machine Owners Instructions 19
Contact SAMSUNG WORLD WIDE If you have any questions or comments relating to Samsung products,please contact the SAMSUNG customer care center.

Country HUNGARY FINLAND

Customer Care Center 79 554
Web Site www.samsung.com/hu www.samsung.com/fi

2. Reference Information

2-1 IC BLOCK

2-1-1 IC601 (HD6473977)

Reference Information

2-1-2 IC301 (SS11511M)

2-1-3 IC302 (LA7411) - 2 Head
2-1-4 IC302 (LA7416) - 4 Head

2-1-5 IC303 (SS23377M)

2-1-6 IC801 (KA8119)
3. Product Specifications and Comparison Chart
3-1 Product Specifications
Design and specifications are subject to change without notice. Operation Format Heads VHS PAL standard Video : 4 or 2 rotary heads Audio/Control : 1 stationary head Erase : 1 full track erase head VHF-I, VHF-III, UHF, Hyperband Standard Standard Standard Standard B/G (for German & West Europe) B/G, LL (for France) B/G, D/K (for East Europe & Middle East Asia) I (for U.K) Description
Receiving channel Television system
Recording system Luminance Colour FM azimuth recording PAL (NTSC/MESECAM) : Down converted subcarrier phase shifted direct recording SECAM : 1/4 counted down subcarrier direct recording NTSC PB on PAL TV SP : 23.39 mm/sec, LP : 11.69 mm/sec SP : 3 hours (E-180 Tape), LP : 6 hours (E-180 Tape) About 100 ~ 190 sec in REW/F.F with E-180 tape
Tape speed Recording/playback time F.F/REW time VIDEO Input Output Signal-to-noise ratio Horizontal resolution Audio Input Output Wow and flutter (WTD) Signal-to-noise ratio Frequency response Power requirement Power consumption Operation temperature Operation humidity Weight Dimensions (W x H x D)
0.5 to 2.0 Vp-p : 75 ohm unbalanced 1.0 0.2 Vp-p : 75 ohm unbalanced Better than 43 dB (SP) More than 240 lines (SP)
-8 dBm, 47 Kohm unbalanced -dBm, 1 Kohm unbalanced 0.4% max (SP) 42 dB min (IHF A filter) 100Hz ~ 8KHz 230V (AC 50/60 Hz) Approx. 18 watts 41F ~ 104F (5C ~ 40C) 10%-75% 4.4 Kg (net) 360 x 92 x 314 mm

3-2 Samsung Electronics

3-2 Comparison Chart

Product Specifications

COUNTRY FINLAND SWEDEN NORWAY FRANCE
MODEL SV-415X SV-410X SV-215X SV-210X SV-415F SV-410F SV-215F SV-210F
HEADS TAPE SPEED S/VIEW V/PLUS 2 SP/LP SP/LP SP SP SP/LP SP/LP SP SP SP/LP SP/LP SP SP SP/LP SP SP SP/LP SP SP/LP SP SP/LP SP SP SP/LP SP/LP SP SP SP/LP SP/LP SP SP SP/LP SP SP O X O X O X O X O X O X O O X O O O O X O X O X O X X X X X X O X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X X
VPS X X X X X X X X X X X X O O X O O O O X X X X X X X X X X X X X X
PDC O X O X O X O X O X O X X X X X X X X X O X X X O X X X X X X O X
ATS AUTO CLOCK O X O X O X O X O X O X O O X O O O O X O X X X O X X X X X X O X O X O X O X O X O X O X O O X O O O O X O X X X O X X X X X X O X
CANAL+ O X O X O O O O O O O O X X O X X X X X O X O O O O O O O O O O O
P/MIERE X X X X X X X X X X X X O X X O X O X X X X X X X X X X X X X X X
VCR/TV O X O X O O O O O X O X O X O O X O X X O X O O O O O O O O O O O

RELEASE 4 HOOKS

REMOVE KNOB-SHUTTLE

(Top view)

RELEASE 3 HOOKS
(Bottom view) Fig. 4-3 Assy Front Panel removal 4-2 Samsung Electronics
4-1-4 Assy Function-Timer removal
Note : Take extreme care not to damage the PCB when removing it.
RELEASE 6 TABS REMOVE 1 SCREW (BH;2-3X10-YELLOW)

RELEASE 1 TAB

Fig. 4-4 Assy Function-Timer removal

4-1-5 Chassis removal

Note : 1. When removing chassis, take extreme care not to damage the main PCB front. 2. When reinstalling the deck on the main PCB, take extreme care not to damage the sensor.
REMOVE 2 SCREWS (BH;2-3X12-YELLOW)
REMOVE 2 SCREWS (BH;2-4X12-YELLOW)
Lift the ass'y full deck up.

CONNECTOR BOARD-ASS'Y

Lift the ass'y main up to remove. RELEASE 1 TAB
RELEASE 1 TAB REMOVE 1 SCREW (BH;3X12-YELLOW)
Fig. 4-5 Chassis Removal 4-4 Samsung Electronics
4-2 Circuit Board Locations

MAIN BOARD

SUB BOARD (SV-415F/410F/215F/210F ONLY)
Fig. 4-6 Circuit Board Locations Samsung Electronics 4-5

FUNCTION-TIMER BOARD

SHUTTLE BOARD
5. Alignment and Adjustment
Note : After replacing the assy full deck, the assy main, the cylinder assy and the micom(IC601), the remote control assy can be used to adjust the X-point (tracking center) adjustment and Head S/W point adjustment.

5-1 Reference

5-1-1 The type of remote control assy

POWER BUTTON

1. Remote control assy (AC93-10039Y/69099-633-252) is specified as a service jig in the service manual of X-5/X-6(DX5-R/DX5-RC/DX6-R/DX6-RC) chassis. (See Fig. 5-1) 2. Normal remote control assy for X-7/X-8 (DX7-R/DX7-RC/DX8-R/DX8-RC) chassis. (See Fig. 5-2)
TRACKING CENTER ADJ. ("INPUT" OR "TEST" AND "1" BUTTON)

CLK/COUNT

WEEKLY

CLR/RST

HEAD S/W ADJ. ("INPUT" OR "TEST" AND "3" BUTTON)

DISPLAY

PRESET

SEARCH

MEMORY

SHIFT SHUTTLE

TRK (TRACKING, FINE) BUTTON PLAY BUTTON
5-1-2 How to identify between normal remote control assy and multi remote control assy for X-7/X-8 chassis (See Fig. 5-2)
1. The color of some buttons related to TV function are gold. 2. Audio button is added instead of the test button hidden behind of inlay. 3. The positions of some buttons are different.

REC INDEX SLOW

P/S INPUT
INPUT BUTTON TEST BUTTON IS HIDDEN BEHIND OF INLAY. REMOTE CONTROL ASS'Y PART NO.

SP/LP BUTTON

OUTPUT 633-252
Fig. 5-1 Remote Control Assy Jig for X-5/X-6 Chassis (AC93-10039Y/69099-633-252)
MULTI REMOTE CONTROL ASS'Y (CAN NOT ADJUST)

VCR POWER TV POWER

NORMAL REMOTE CONTROL ASS'Y (CAN ADJUST)

GOLD COLOR

POWER BUTTON TRACKING CENTER ADJ. ("INPUT" OR "TEST" AND "1" BUTTON) SPEED BUTTON

SYSTEM

CLR/RST INPUT
HEAD S/W ADJ. ("INPUT" OR "TEST" AND "3" BUTTON) INPUT BUTTON TRK (TRACKING, FINE) BUTTON PLAY BUTTON

DISP./

GOLD COLOR GOLD COLOR GOLD COLOR

CLR/RST -/-INPUT

VOLUME

SHUTTLE

REC MENU Q-PRO

SOFTEN

SHARPEN TV/VCR

SLOW PICTURE

A.DUB PICTURE

SLOW AUDIO

TEST BUTTON IS HIDDEN BEHIND OF INLAY.

ADD BUTTON(AUDIO)

Fig. 5-2 Remote Control Assy for X-7/X-8 Chassis Samsung Electronics 5-1

Alignment and Adjustment

5-2 Mechanical Adjustment
Note : Refer to the Mechanical Manual DX7-A/DX7-AC/DX8-A/DX8-AC (AC68-20392A) for the adjustment and confirmation of assy full deck.
5-2-1 The number and position of test point
Test point : TP02 (CTL Pulse) TP03 (HD S/W -Trigger) TP04 (V. Envelope) TP05 (Audio out)
AUDIO OUT HD S/W -TRIGGER

SCART CTL AGC

H'D SW

V.OUT A.OUT

TP04 TP03 TP02

TP08 TP07

CTL PULSE V. ENVELOPE
Fig. 5-3 The position of test point (Main PCB-Component side) 5-2 Samsung Electronics
5-2-2 X-Point(Tracking center) adjustment (See the 2-2-1 (d) AC HEAD POSITION(X-POINT) ADJUSTMENT on page 2-3 of the mechanical manual)
5-2-2 (a) IF THE REMOTE CONTROL ASSY IS NOT AVAILABLE
1. Playback the colorbar alignment tape. 2. Connect CH-1 scope probe to TP02 and CH-2 scope probe to TP03. And then, trigger head switching pulse. 3. Set tracking preset to 11msec (2head : 2.7msec, 4, 6head : 11msec) using the FINE (ADJUST) button / of the other remote control assy except the remote control assy jig for X-5/ X-6 chassis and the normal remote control assy for X-7/X-8 chassis. 4. Insert the adjusting driver (+) into X-position adjusting gear. Adjust the driver in either direction for maximum envelope waveform. Note : Since the adjusting gear unit may be damaged, do not adjust by force when adjusting the X-point using the adjusting driver (+). After turn the X-point adjusting screw (D) counterclockwise a little, perform the adjustment. After adjustment is completed, tighten the screw. <Setting of scope> - Volt/div. : CH-1 = 0.1V CH-2 = 0.2V CH-2 Probe TP02 H'D S/W Pulse CH-1 Probe TP03 CTL Pulse 2.7msec (2 Head), 11msec (4, 6 Head) Fig. 5-4 Tracking preset adjustment REMOTE BUTTONS

SCREW(B) AZIMUTH ADJUST

SCREW(C) TILT ADJUST
X-POSITION ADJUST GEAR HOLE

SCREW(A) HEIGHT ADJUST

SCREW(D) X-POINT LOCKING
Fig. 5-6 Location of A/C Head adjustment screw
5-2-2 (b) IF THE REMOTE CONTROL ASSY (AC93-10039Y/69099-633-252) IS AVAILABLE

Note : How to use the TEST button. 1. Disattach the inlay of remote control assy. (See Fig. 5-1 and Fig. 5-2) 2. Press the TEST button with the pincers and the precise driver as shown in Fig. 5-1 and 5-2) 1. When using the INPUT button of remote control assy; 1) Simultaneously press the INPUT button and 1 button in PB mode. This will adjust the tracking center automatically. 2) Set the tracking preset using the FINE (ADJUST) button of remote control. 3) After adjustment is completed, press the POWER button to release. 2. When using the TEST button of remote control assy ; 1) Simultaneously press the TEST button and 5 button in PB mode. This will adjust the tracking center automatically. 2) Set the tracking preset using the FINE (ADJUST) button of remote control. 3) After adjustment is completed, press the POWER button to release.

- Time/div. : 5msec

CONTROL PULSE REMOVE
Fig. 5-5 Tracking preset adjustment Samsung Electronics 5-3
5-2-2 (b) IF THE NORMAL REMOTE CONTROL ASSY OF X-7/X-8(DX7-R/DX7-RC/ DX8-R/DX8-RC) CHASSIS IS AVAILABLE
Note 1 : Two kinds of remote control assy are used for X-7/X-8(DX7-R/DX7-RC/DX8-R/ DX8-RC) chassis. 1. One is a normal remote control assy, the other is a multi remote control assy 2. All adjustments are adjusted by normal remote control assy only. 3. For the identification of normal remote control assy and multi remote control assy, See page 5-1. Note 2 : How to use the TEST button. 1. Disattach the inlay of remote control assy. (See Fig. 5-1 and Fig. 5-2) 2. Press the TEST button with the pincers and the precise driver as shown in Fig. 5-1 and 5-2) 1. When using the INPUT button of remote control assy; 1) Simultaneously press the INPUT button and 1 button in PB mode. This will adjust the tracking center automatically. 2) Set the tracking preset using the FINE (ADJUST) button of remote control. 3) After adjustment is completed, press the POWER button to release. 2. When using the TEST button of remote control assy ; 1) Simultaneously press the TEST button and 5 button in PB mode. This will adjust the tracking center automatically. 2) Set the tracking preset using the FINE (ADJUST) button of remote control. 3) After adjustment is completed, press the POWER button to release.
5-3 Electrical Adjustment
5-3-1 Head S/W Adjustment
Note : Only remote control assy can adjust.
5-3-1 (a) IF REMOTE CONTROL ASSY (AC93-10039Y/69099-633-252) IS AVAILABLE
1. When using the INPUT button of remote control assy ; 1) Insert an SP tape into the housing assy. 2) Press the PLAY button. 3) Press the INPUT button and 3 button simultaneously. 4) This will adjust the head S/W point adjustment automatically. 5) After the adjustment is completed, press POWER button to release. 2. When using the TEST button of remote control assy ; 1) Insert an SP tape into the housing assy. 2) Press the PLAY button. 3) Press the TEST button and SP/LP button simultaneously. 4) This will adjust the head S/W point adjustment automatically. 5) After adjustment is completed, press the POWER button to release.

Description and Specification SCREW-TAPPING;BH,-,-,M3,L8,FZY SCREW-TAPPING;BH,+,-,M2.6XL7.5,ZPC3 SCREW-MACHINE;-,PH,+,-,M3,L3,FE,FZY,YEL WASHER-SLIT;-,ID2.5,OD5.0,T0.5,POLY SLID WASHER-PLAIN;PLAIN,M3.2,D6,T0.5,POLYSLID WASHER-SLIT;PLAIN,ID2.5,OD7,T0.5,SPC1,-, WASHER-SLIT;-,D2.5,D9.0,T0.5,NUMIRROR,-, SLIDER-MAIN;TOPEX 4010S,-,-,-,GEAR-LOADING L ASSY;-,-,-,PACKAGE,-,X-5, GEAR-LOADING R ASSY;-,-,-,-,-,X5,SPRING-BRAKE CAPSTAN;ES,SUS304WPB,PI0.4, GEAR-MASTER;POM (M90-44),M 1,Z 60,SP,-,X MOTOR-D/D CAPSTAN;DMVCMC07A,-,BELT-CAPSTAN;-,DLB-601,T2,8,L134.9,BLK,X GEAR-CLUTCH ASSY;X-5,-,-,-,-,-,LEVER-SLIDER PINCH;PBT,T4,NAT,-,-,GEAR- WORM WHEEL;POM SW-01,M0.55/M1,Z57/ LEVER- SHIFT;PBT2002K,T10.9,L35,-,-,LEVER- IDELR CHANGE;PBT330,T33,L50,-,W6. SPRING-LEVER SHIFT;TS,SWPB,PI0.7,D5.5,L1 UNIT-LOADING ASSY;X-5,-,MOTOR-LOADING ASSY;POM+RF370C X-5 GEAR- WORM LO;PBT 2002K,-,-,-,D4.5,3,HOLDER SHAFT;POM M90-44,T1.25,NTR,PI5XH5 BRAKE CAPSTAN;-,-,-,-,X5,-

6-4 Housing Assembly

H510 902

H532 H531 H535

914 H540 H545 H544 H541 914

H542 H543

Loc. No H500 H510 H520 H521 H522 H524 H526 H530 H531 H532 H533 H535 H540 H541 H542 H543 H544 H545 H550 6-8
Part No AC60-10051A AC60-10067A AC61-82014D AC61-10006A AC61-20932B AC61-20922B AC66-30018A AC61-60121A AC66-30019A AC61-11033A AC61-10004A AC66-30004A AC61-60142A AC66-30017A AC61-11032A AC61-10003A AC66-80008A AC61-60120A AC66-30016A AC61-60123A AC61-50654A
Description and Specification SCREW-TAPPING;BH,-,-,M3,L8,FZY SCREW-TAPTITE;PWH,+,-,M3,L8,MFZN2-C,SWCH HOUSING-ASSY;-,X7FL26280B,230X130X60,-,X CHASSIS- UPPER;SECC 20/20,-,T1.0,BLK,-,X HOLDER-CASSETTE ASSY;-,X5FL06080A,-,-,-, HOLDER-CASSETTE;-,SECC T1.2,-,NAT,-,X-7( LEVER-LOCK R;SECC 20/20,T1.2,L44,W32,-,SPRING-LEVER LOCK;ES,SUS304 WPB,PI0.2,D2 LEVER-KEY CASSETTE;LUCEL N109-LD,T2.5,L2 CHASSIS-SIDE L ASSY;-,-,-,-,-,X5FL0505A, CHASSIS- SIDE L;ABS HF-380,-,T10,BLK,-,X LEVER- LIGHT SHUTTER;LUCEL N109-LD,T2.5, SPRING- LIGHT;ES,SUS304WPB,PI0.2,L11.4(O LEVER- DOOR;LUCELN109-LD,T3.5,L74.3,W21. CHASSIS-SIDE R ASSY;-,-,-,-,-,X5FL0505A, CHASSIS- SIDE R;ABS HF-380,-,T10,BLK,-,X SLIDER DAMPER;LUCEL N109-LD,T4,L87,-,-,SPRING-SLIDER;ES,SUS 304WPB,PI0.4,D3.8,L LEVER- LID OPENER;LUCEL N109-LD,T4.0,L34 SPRING-LID OPENER;TS,SWPB,PI0.55,D8.9,L1 SHAFT-ARM ASSY;-,SUM24L,-,-,-,-,X-5
Loc.No Part No SMPS/POWER PARTS C1P01 2401-001952 C1P02 2301-000383 C1P03 C1P04 C1P05 C1P06 C1P09 C1P10 C1S03 C1S04 C1S05 C1S06 C1S08 C1S09 C1S10 C1S16 C1S21 C1S22 C1S23 C1S30 C1S31 C1S32 C1S33 C1S34 C1S35 C1S38 CN1S1 D1P01 D1P02 D1P03 D1P04 D1P06 D1P20 D1S01 D1S02 D1S03 D1S04 D1S05 D1S07 D1S08 D1S30 D1S31 D1S33 D1S43 F1S01 IC1P01 IC1S2 IC1S3 L1S01 L1S02 L1S03 L1S05 2203-001724 2401-001975 2401-001978 2401-001915 2401-001912 2202-000797 2305-001021 2305-001021 2201-000808 2201-000934 2401-003302 2201-000934 2201-000915 2201-000795 2401-000905 2301-000361 2301-000442 2401-000385 2401-001134 2401-001998 2401-001125 2401-002162 2401-001355 2301-000129 3711-000178 0402-000132 0402-000132 0402-000132 0402-000132 0401-000101 0402-000132 0402-001009 0402-001009 0402-001009 0402-001009 0402-000378 0402-001013 0401-000101 0402-001013 0402-001013 0402-000431 0402-001069 A3065-0157 AC14-12001E 0604-011028 AC14-12006D AC29-30050A A1151-0042 3301-000297 AC27-92001M ASSY-MAIN Desc and Spec Remark S.N.A Loc.No L1S30 L1S31 L1S32 L1S33 PT1S01 Q1P01 Q1P02 Q1P03 Q1P04 Q1P05 Q1P06 Q1P07 Q1S01 Q1S02 R1P01 R1P02 R1P03 R1P04 R1P05 R1P06 R1P07 R1P09 R1P10 R1S03 R1S06 R1S07 R1S11 R1S12 R1S13 R1S14 R1S16 R1S19 R1S21 R1S30 R1S31 R1S32 R1S33 R1S34 VA1S01 VA1S02 ZD1P01 ZD1P02 ZD1S30 Part No AC27-12001N AC27-12001N AC27-92001M AC27-92001M AC26-20120E 0501-000610 0504-000116 0501-000610 0504-000118 0501-000616 0501-000616 0501-000398 0502-001050 0501-000442 2004-001096 2004-001096 2001-000273 2001-000611 2001-000449 2001-000429 2007-001637 2004-000571 2001-000449 2001-000305 2006-000273 2001-000003 2006-000262 2001-000305 2001-000305 2001-000305 2003-000264 2001-000003 2003-000119 2001-000515 2001-000221 2001-000429 2004-000869 2004-000459 1405-000186 1405-000186 0403-000390 0403-000717 0403-000571 Desc and Spec COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,COIL-CHOKE;10UH-15%,RA,K-30,Q80,150KHZ,INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,TRANS-SWITCHING;DP,120V,UL/CSA,EE2821,1. TR-SMALL SIGNAL;KSA928A-Y,PNP,1W,TO-92L, TR-DIGITAL;KSR1001,NPN,300mW,4.7K-4.7K,T TR-SMALL SIGNAL;KSA928A-Y,PNP,1W,TO-92L, TR-DIGITAL;KSR1003,NPN,300mW,22K-22K,TOTR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L TR-SMALL SIGNAL;KSC2328A-Y,NPN,1W,TO-92L TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-POWER;2SC4517A,NPN,30W,TO-220,ST,10TR-SMALL SIGNAL;KTC3203-Y,NPN,400MW,T0-9 R-METAL;560ohm,5%,1/4W,AA,TP,2.4X6.4mm R-METAL;560ohm,5%,1/4W,AA,TP,2.4X6.4mm R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;3.9Kohm,5%,1/4W,AA,TP,2.4x6.4mm R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1.2Kohm,5%,1/8W,DB,BK,2012 R-METAL;220ohm,5%,1/4W,AA,TP,2.4x6.4mm R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CEMENT;27Kohm,5%,2W,CA,BK,6.4x27x6.4m R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CEMENT;2.7ohm,10%,2W,CB,ST,7.5x11x20. R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;110Kohm,5%,1/8W,AA,TP,1.8x3.2m R-METAL OXIDE;300ohm,5%,1W,AD,TP,4.3x12m R-CARBON;330ohm,5%,1/8W,AA,TP,1.8x3.2mm R-METAL OXIDE;0.68ohm,5%,2W,AE,TP,6x16mm R-CARBON ;220OHM,5%,1/8W,AA,TP R-CARBON;1.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-METAL;3Kohm,1%,1/8W,AA,TP,1.8x3.2mm R-METAL;2.2Kohm,1%,1/8W,AA,TP,1. VARISTOR;470V,4500A,17x12mm,TP VARISTOR;470V,4500A,17x12mm,TP DIODE-ZENER;UZP33B,33V,31.4-34.6V,1W,DODIODE-ZENER;MTZJ5.1B,5.1V,4.94-5.2V,500m DIODE-ZENER;UZP43B,43V,40-46V,1W,DO-41,T Remark

C-AL;4.7UF,20%,50V,-,TP,6.3X7,5 C-FILM,PEF;10nF,5%,50V,6x7x3.2mm,5mm,TP C-CERAMIC,CHIP;4.7UF,+80-20%,16V,Y5V,321 C-AL;47UF,20%,16V,GP,TP,5X11MM,5 C-AL;47UF,20%,25V,GP,TP,6.3X5,5 C-AL;1uF,20%,50V,GP,TP,3x5,1mm C-AL;1uF,20%,50V,GP,5x11mm,2mm,BK C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP, C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13. C-FILM,MPEF;100nF,20%,275V,TP,17.5x7x13. C-CERAMIC,DISC;2.2nF,10%,400V,Y5P,12x7.5 C-CERAMIC,DISC;3.3nF,20%,400V,Y5P,18x8,1 C-AL;47uF,20%,400V,GP,TP,18X31.5,7. C-CERAMIC,DISC;3.3nF,20%,400V,Y5P,18x8,1 C-CERAMIC,DISC;100pF,10%,1KV,Y5P,TP,6x5, C-CERAMIC,DISC;10nF,10%,400V,Y5P,15x10,5 C-AL;22UF,20%,16V,BP,-,6X11,2.5MM C-FILM,PEF;1.2NF,10%,50V,TP,-,5MM C-FILM,PEF;4.7nF,10%,50V,TP,5.5x7x3mm,5m C-AL;10UF,20%,100V,GP,-,6.3X11,2.5M C-AL;330UF,20%,35V,WT,TP,10X16,5MM C-AL;1000uF,20%,25V,GP,TP,10x20,5mm C-AL;330UF,20%,25V,WT,TP,10X12.5,5M C-AL;1000uF,20%,25V,WT,TP,10x20,5mm C-AL;470UF,20%,10V,GP,-,8X11.5,5MM C-FILM,PEF;100nF,5%,50V,10X9X4.3X5,5mm,T CONNECTOR-HEADER;1WALL,2P,1R,3.96mm,STRA DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1SR139,600V,1A,MSR DIODE-RECTIFIER;1SR139,600V,1A,MSR DIODE-RECTIFIER;1SR139,600V,1A,MSR DIODE-RECTIFIER;1SR139,600V,1A,MSR DIODE-RECTIFIER;EG01C,1000V,500mA,DO-41 DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;1SR153-400,400V,800mA,DO DIODE-RECTIFIER;FML-M02S,200V,2.5A,TO-22 DIODE-RECTIFIER;RL10Z,200V,2A,DO,TP FUSE;FST 250V 1.6A 20MM SEMKO S505 C IC;KA7809,-,PHOTO-COUPLER;PS2561-1 ST DIP IC;KA431Z,TO-92,TAPING FILTER-LINE NOISE;-,400UH,-,250V,COIL-LINE FILTER;BSF-2120Z 25MH 3.2OHM CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, INDUCTOR;70UH-M RT BFS3565R2F,-,-,-,-
SYSTEM CONTROL/SERVO C601 2203-002188 C602 2202-000807 C603 2203-001557 C604 2203-002188 C605 C606 C607 C608 C609 2202-000791 2202-000797 2203-002188 2203-001557 2203-001679
C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-CERAMIC,MLC-AXIAL;22NF,+80-20%,25V,Y5V C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-CERAMIC,MLC-AXIAL;150PF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP, C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;68NF,+80-20%,25V,Y5V,TP,2

Electrical Parts List

Loc.No C610 C6101 C6102 C6103 C6104 C6105 C6106 C6107 C611 C6114 C6116 C6117 C6119 C612 C6120 C6122 C6123 C6124 C6125 C6126 C6127 C613 C614 C615 C616 C617 C618 C619 C620 C623 C624 C625 C626 C627 C628 C630 C632 C633 C634 C635 C636 C637 C638 C639 C640 C642 C643 C645 C650 C651 C652 C660 C661 C663 C671 C675 C676 C677 C678 C681 Part No 2203-001679 2202-000780 2203-000239 2202-000216 2202-000216 2203-002188 2301-000392 2203-000818 2201-000928 2201-000800 2203-001612 2203-001612 2401-001975 2202-000791 2202-000780 2401-001952 2401-001978 2401-001325 2203-002188 2401-000419 2203-001659 2203-001557 2203-002188 2203-002188 2203-001696 2202-000796 2203-001702 2203-001696 2203-001696 2203-001580 2203-001580 2203-001580 2203-001580 2202-000807 2202-000807 2202-000780 2401-001511 2401-001904 2401-000208 2401-000199 2401-001978 2401-001978 2401-001915 2401-001904 2401-001978 2401-000912 2401-000912 2203-000477 2203-002188 2401-001511 2202-000780 2203-001702 2203-001702 2203-000374 2203-001557 2401-001975 2202-000797 2202-000797 2401-001915 2203-001557 Desc and Spec C-CERAMIC,CHIP;68NF,+80-20%,25V,Y5V,TP,2 C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5 C-CERAMIC,CHIP;100pF,5%,50V,NPO,TP,2012, C-CERAMIC,MLC-AXIAL;27pF,5%,50V,SL,TP,3. C-CERAMIC,MLC-AXIAL;27pF,5%,50V,SL,TP,3. C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-FILM,PEF;15nF,5%,50V,6.5x8.5x3.2mm,5mm C-CERAMIC,CHIP;33pF,5%,50V,NPO,TP,2012,C-CERAMIC,DISC;2.7NF,20%,16V,Y5R,TP,3.5X C-CERAMIC,DISC;120PF,5%,50V,SL,TP,5X3,5 C-CERAMIC,CHIP MELF;22PF,5%,50V,SL,TP,20 C-CERAMIC,CHIP MELF;22PF,5%,50V,SL,TP,20 C-AL;47UF,20%,16V,GP,TP,5X11MM,5 C-CERAMIC,MLC-AXIAL;150PF,10%,50V,Y5P,TP C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5 C-AL;4.7UF,20%,50V,-,TP,6.3X7,5 C-AL;47UF,20%,25V,GP,TP,6.3X5,5 C-AL;470nF,20%,50V,GP,TP,3x5,5 C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-AL;10UF,20%,16V,GP,-,4X7,5 C-CERAMIC,CHIP MELF;47PF,5%,50V,SL,TP,20 C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-CERAMIC,CHIP MELF;82PF,10%,50V,Y5P,TP, C-CERAMIC,MLC-AXIAL;UP050 B102KB INF,10% C-CERAMIC,CHIP;2.2nF,5%,50V,X7R,2012,-,T C-CERAMIC,CHIP MELF;82PF,10%,50V,Y5P,TP, C-CERAMIC,CHIP MELF;82PF,10%,50V,Y5P,TP, C-CERAMIC,CHIP MELF;15PF,5%,50V,SL,TP,20 C-CERAMIC,CHIP MELF;15PF,5%,50V,SL,TP,20 C-CERAMIC,CHIP MELF;15PF,5%,50V,SL,TP,20 C-CERAMIC,CHIP MELF;15PF,5%,50V,SL,TP,20 C-CERAMIC,MLC-AXIAL;22NF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;22NF,+80-20%,25V,Y5V C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5 C-AL;47UF,20%,16V,GP,-,6X7,5 C-AL;10UF,20%,16V,-,TP,4X7MM,5 C-AL;100nF,+80-20%,5.5V,GP,TP,12.3m C-AL;1000UF,20%,6.3V,GP,TP,10X12.5, C-AL;47UF,20%,25V,GP,TP,6.3X5,5 C-AL;47UF,20%,25V,GP,TP,6.3X5,5 C-AL;1uF,20%,50V,GP,TP,3x5,1mm C-AL;10UF,20%,16V,-,TP,4X7MM,5 C-AL;47UF,20%,25V,GP,TP,6.3X5,5 C-AL;22UF,20%,16V,GP,-,5X5,5 C-AL;22UF,20%,16V,GP,-,5X5,5 C-CERAMIC,CHIP;1uF,+80-20%,16V,Y5V,TP,20 C-CERAMIC,CHIP;10NF,+80-20%,16V,Y5V,TP,2 C-AL;47UF,20%,16V,GP,-,6X7,5 C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5 C-CERAMIC,CHIP;2.2nF,5%,50V,X7R,2012,-,T C-CERAMIC,CHIP;2.2nF,5%,50V,X7R,2012,-,T C-CERAMIC,CHIP;15nF,10%,50V,X7R,TP,2012, C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, C-AL;47UF,20%,16V,GP,TP,5X11MM,5 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP, C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP, C-AL;1uF,20%,50V,GP,TP,3x5,1mm C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, Remark Loc.No C682 C698 CN601 CN602 CN603 CN604 CN605 D605 D608 D609 D6102 D6104 D6105 D6106 D611 D612 D613 D614 D615 IC601 Part No 2202-000780 2203-001557 3708-001251 3711-002445 3711-003749 3708-001165 3708-001163 0402-000132 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0402-000132 0402-000132 0402-000132 0401-000101 0401-000101 Refer to table below Country Italy/Spain/Portugal/U.K Germany/Poland/Hungary/Austria Switzerlands/Bulgaria/Czech./Romania France/Netherlands/Finland/Sweeden/Norway Denmark/Greece/Croatia/Slovenia Switzerlands - SV-210F IC602 IC603 IC604 IC605 IC606 L601 L602 L603 L604 L605 L606 L6101 L6103 L6P02 LD601 PT601 PT602 Q601 Q602 Q604 Q607 Q608 Q609 Q6101 Q6102 Q6106 Q6108 R601 R602 R604 R605 R606 1003-001090 1201-000230 AC14-12006C 1103-001020 AC14-12009E AC27-92001B AC27-92001B AC27-92001B 2701-000131 AC27-92001B 3301-000297 AC27-92001B 2701-000117 3301-000297 0601-000495 0604-000188 0604-000188 0501-000398 0501-000398 0501-000303 0504-000142 0504-000203 AC14-12001G 0501-000398 0501-000398 0501-000398 0501-000303 2001-000832 2001-000679 2007-001472 2007-001589 2007-000658 Desc and Spec Remark

C-CERAMIC,MLC-AXIAL;100nF,+80-20%,50V,Y5 C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, CONNECTOR-FPC/FC/PIC;22P,1mm,STRAIGHT-F, CONNECTOR-HEADER;BOX,2P,2R,1.5MM,STRAIGH CONNECTOR-HEADER;BOX,8P,2R,2mm,STRAIGHT, CONNECTOR-FPC/FC/PIC;6P,1.25mm,STRAIGHT, CONNECTOR-FPC/FC/PIC;5P,1.25mm,STRAIGHT, DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-RECTIFIER;1N4004,400V,1A,DO-41 DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, IC-MCU;100PIN,QFP Part No AC09-10457F AC09-10456L Specification HD6433977RA90F HD6433977RA87F

AC09-10457K

HD6433977RA92F
IC-MOTOR DRIVER;LB1643,SIP,10P,-,SINGLE, IC-OP AMP;6324,DIP,14P,-,QUAD,15/100mV,P IC;KA7533,DIP,IC-EEPROM;24LC04,4Kx8BIT,DIP,8P,300MIL,IC;HCF4094BE/TC4094BP,DIP,LOGIC COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,INDUCTOR-AXIAL;15UH,5%,2.4X3.4MM COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,INDUCTOR-AXIAL;10uH,5%,2.4x3.4mm CORE-FERRITE BEAD;AA,3.6x1.2x5.7mm,1400, LED-IR;ROUND,3mm,150mW,6V,950nm,BK PHOTO-INTERRUPTER;TR,-,-,DIP-4,TR PHOTO-INTERRUPTER;TR,-,-,DIP-4,TR TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSA733-Y,PNP,250mW,TO-92 TR-DIGITAL;KSR2001,PNP,300mW,4.7K-4.7K,T TR-DIGITAL;KSR1008,NPN,300mW,47K-47K,TOIC;KA78L05,T,TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSA733-Y,PNP,250mW,TO-92 R-CARBON;510ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;36KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CHIP,MELF;68KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CHIP;27ohm,5%,1/10W,DA,TP,2012
Loc.No R607 R608 R610 R6100 R6101 R6102 R6103 R6104 R6105 R6106 R6107 R6109 R6110 R6111 R6112 R6113 R6115 R6116 R6117 R6119 R612 R6120 R6121 R6122 R6123 R6124 R6125 R6128 R6129 R6130 R6131 R6134 R614 R615 R616 R617 R618 R619 R620 R621 R624 R625 R626 R627 R628 R629 R630 R631 R632 R633 R634 R635 R636 R637 R639 R640 R641 R642 R643 R644 Part No 2007-001587 2007-001637 2001-000947 2001-000613 2007-001629 2007-001497 2001-000290 2007-001507 2001-000429 2007-001586 2001-000429 2001-000241 2007-001503 2007-001497 2001-000281 2001-000660 2007-001589 2001-001031 2001-000850 2001-000864 2001-000539 2007-001586 2001-000429 2007-001623 2007-001503 2001-000633 2001-000633 2001-000534 2001-000281 2001-000515 2001-000281 2007-001486 2001-000508 2001-000508 2001-000832 2007-001623 2007-001623 2007-001557 2007-001495 2001-000864 2001-000273 2001-000290 2007-001589 2001-000290 2001-000508 2001-000508 2001-000347 2007-001591 2001-000429 2001-000802 2001-000331 2007-001589 2001-000281 2001-000429 2001-000429 2001-000429 2001-000429 2001-000290 2001-000290 2001-000429 Desc and Spec R-CHIP,MELF;1Kohm,5%,1/8W,DB,TP,2012 R-CHIP,MELF;1.2Kohm,5%,1/8W,DB,BK,2012 R-CARBON;7.5KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON ;3.9K OHM,5%,1/8,AA,T R-CHIP,MELF;1.8Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;5.6KOHM,5%,1/8W,DB,BK,2012 R-CARBON ;10K OHM,5%,1/8W,AA,T R-CHIP,MELF;470KOHM,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Mohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1.5Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CHIP,MELF;47KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;5.6KOHM,5%,1/8W,DB,BK,2012 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON;91KOHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON;560Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;24Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Mohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;10Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;47KOHM,5%,1/8W,DB,BK,2012 R-CARBON;30Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;30Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;240ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;220OHM,5%,1/8W,AA,TP R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;56KOHM,5%,1/8W,DB,BK,2012 R-CARBON ;220K OHM,5%,1/8W,AA, R-CARBON ;220K OHM,5%,1/8W,AA, R-CARBON;510ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;10Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;10Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;270ohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;510OHM,5%,1/8W,DB,BK,2012 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;100Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON ;10K OHM,5%,1/8W,AA,T R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON ;220K OHM,5%,1/8W,AA, R-CARBON ;220K OHM,5%,1/8W,AA, R-CARBON;13Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;18Kohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;12Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm Remark Loc.No R645 R646 R647 R648 R649 R651 R652 R653 R654 R655 R656 R657 R658 R659 R660 R661 R662 R663 R664 R665 R666 R667 R668 R669 R670 R671 R672 R673 R674 R675 R676 R677 R679 R681 R682 R683 R684 R686 R687 R688 R689 R690 R691 R692 R693 R694 R695 R696 R697 RS601 S601 S602 SW601 XT601 XT602 XT6102 J501 J602 W132 W133 Part No 2001-000429 2001-000347 2001-000347 2007-001589 2001-000429 2001-000786 2001-000429 2001-000864 2001-000864 2001-000429 2001-000429 2001-000429 2001-000429 2001-000449 2001-000281 2001-000429 2001-000429 2001-000429 2001-000429 2001-000362 2001-000429 2001-000429 2001-000362 2001-000290 2001-000012 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2007-001589 2001-000429 2001-000429 2001-000429 2001-000429 2001-000429 2007-001586 2001-000429 2001-000290 2001-000429 2001-000429 2001-000429 2001-000429 2001-000290 2001-000290 2001-000539 2003-000259 3409-000176 0603-000112 0603-000112 AC34-22001E 2801-003293 2801-003318 2801-003311 2203-001557 2007-001589 2001-000449 2001-000449 Desc and Spec R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;13Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;13Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;47KOHM,5%,1/8,AA,TP, R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;100ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;150ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;150ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;680Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1Mohm,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;24Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-METAL OXIDE;3.9OHM,5%,2W,AE,TP,6X16MM SWITCH-DETECTOR;30Vdc,100mA,SPST,-,PHOTO-TR;NPN,35V,6V,50mA,75mW,PHOTO-TR;NPN,35V,6V,50mA,75mW,SWITCH-PROGRAM;MXS00281MLB0,-,-,-,-,-,-, CRYSTAL-UNIT;10MHZ,50PPM,28-AAA,16PF,50O CRYSTAL-UNIT;32.768KHz,20ppm,28-AAP,12.5 CRYSTAL-UNIT;17.734475MHz,50ppm,28-AAA,1 C-CERAMIC,CHIP;100NF,+80-20%,25V,Y5V,TP, R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m Remark

4HEAD 2HEAD

Loc.No Q312 Q3A01 Q3A02 Q3A03 Q3A04 Q3A05 R301 R302 R303 R304 R305 R306 R307 R309 R310 R311 R312 R313 R314 R315 R316 R317 R318 R319 R320 R321 R322 R323 R324 R325 R328 R329 R331 R332 R333 R335 R337 R338 R339 R340 R341 R350 R351 R399 R3A02 R3A03 R3A04 R3A05 R3A06 R3A07 R3A08 R3A09 R3A10 R3A11 R3A12 R3A13 R3A14 R3A15 R3A16 R3A17 Part No 0501-000398 0501-000231 0501-000231 0501-000010 0501-000303 0501-000398 2001-000302 2001-000302 2007-001568 2001-000522 2007-001629 2001-000864 2007-001627 2007-001553 2007-001546 2007-001454 2007-001553 2007-001513 2007-001557 2007-001546 2007-001458 2007-001534 2007-001534 2007-001521 2007-001637 2007-001521 2007-001633 2007-001513 2007-001633 2007-001536 2007-001637 2007-001584 2007-001584 2007-001589 2007-001458 2007-001616 2007-001578 2007-001513 2001-000429 2001-000449 2001-000472 2007-001629 2007-001616 2007-001536 2001-000405 2001-000780 2007-001629 2007-001584 2007-001584 2001-000458 2001-000290 2001-000522 2007-001633 2007-001534 2001-000362 2001-000645 2001-000734 2007-001612 2007-001641 2007-001497 Desc and Spec TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;2SD1468SQ,NPN,300MW,TO-9 TR-SMALL SIGNAL;2SD1468SQ,NPN,300MW,TO-9 TR-SMALL SIGNAL;KSC1008,NPN,80V,60V,700m TR-SMALL SIGNAL;KSA733-Y,PNP,250mW,TO-92 TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;10ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;22Kohm,5%,1/8W,DB,BK,2012 R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1.8Kohm,5%,1/8W,DB,BK,2012 R-CARBON;56Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;100Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;3.9KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;820OHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;4.7KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;270ohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;3.9KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;8.2KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;33KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;33KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;390OHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1.2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;390OHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1.5Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;4.7KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1.5Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;330OHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1.2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;1Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;8.2KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;120Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.7Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;4.7KOHM,5%,1/8W,DB,BK,2012 R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;2.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;2.7Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CHIP,MELF;1.8Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;120Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;330OHM,5%,1/8W,DB,BK,2012 R-CARBON ;180 OHM,5%,1/8W,AA,T R-CARBON ;470 OHM,5%,1/8W,AA,T R-CHIP,MELF;1.8Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.2Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.2Kohm,5%,1/8W,DB,BK,2012 R-CARBON;2.2OHM,5%,1/8W,AA,TP,1.8X3.2MM R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;22Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CHIP,MELF;1.5Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;33KOHM,5%,1/8W,DB,BK,2012 R-CARBON;150ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;330Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CHIP,MELF;12Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;0OHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;5.6KOHM,5%,1/8W,DB,BK,2012 Remark Loc.No R3A18 R3A19 R3A20 R3A21 R3A22 R3A23 R3A24 R3A25 R3A26 R3A27 R3A28 R3A29 R3A30 R3A31 XT301 IF PARTS C402 C403 C410 D410 L401 L415 Q401 R401 R402 R403 R405 R406 R407 R418 U401 Part No 2001-000718 2001-000221 2001-000786 2007-001503 2007-001503 2007-001484 2001-000454 2007-001482 2007-001468 2007-001513 2007-001623 2007-001580 2001-000613 2001-000734 2801-001397 Desc and Spec R-CARBON;4.3KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;1.2Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON ;47KOHM,5%,1/8,AA,TP, R-CHIP,MELF;47KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;47KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;6.2KOHM,5%,1/8W,DB,BK,2012 R-CARBON;2.2Mohm,5%,1/8W,AA,TP,1.8x3.2m R-CHIP,MELF;6.8KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;7.5KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;4.7KOHM,5%,1/8W,DB,BK,2012 R-CHIP,MELF;10Kohm,5%,1/8W,DB,BK,2012 R-CHIP,MELF;2.4Kohm,5%,1/8W,DB,BK,2012 R-CARBON ;3.9K OHM,5%,1/8,AA,T R-CARBON;4.7Kohm,5%,1/8W,AA,TP,1.8x3.2m CRYSTAL-UNIT;4.433619MHZ,20PPM,28-AAA,S, Remark

Loc.No R4N20 R4N22 R4N23 TL4L01 VR4L01 VR4L02 Part No 2001-000241 2001-000802 2001-000554 AC26-12001A 61247-102-223 61247-102-223 2401-001893 2202-000797 2202-000796 2401-001904 2202-000796 2401-001915 3708-001251 3708-001164 3708-001163 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0401-000101 0703-001042 3722-000433 AC37-22001T AC27-92001B 2701-000181 0501-000398 0501-000398 0501-000398 0501-000398 0501-000398 0501-000398 0501-000398 0501-000398 0501-000290 0501-000290 0501-000290 0501-000290 0501-000290 0501-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 2001-000290 Desc & Spec R-CARBON;1.5Kohm,5%,1/8W,AA,TP,1.8x3.2m R-CARBON;5.6KOHM,5%,1/8W,AA,TP,1.8X3.2M R-CARBON;270OHM,5%,1/8W,AA,TP,1.8X3.2MM TRANS-DET;9MM,0UH,BLK,8PF,77.9MHZ,M7T1,S VR-SEMI;EVN-DCY A03 BE4 TAPG 22KB VR-SEMI;EVN-DCY A03 BE4 TAPG 22KB ASSY-F/TIMER C-AL;100uF,20%,16V,GP,TP,6.3x7mm,5 C-CERAMIC,MLC-AXIAL;10NF,30%,16V,Y5P,TP, C-CERAMIC,MLC-AXIAL;UP050 B102KB INF,10% C-AL;10UF,20%,16V,-,TP,4X7MM,5 C-CERAMIC,MLC-AXIAL;UP050 B102KB INF,10% C-AL;1uF,20%,50V,GP,TP,3x5,1mm CONNECTOR-FPC/FC/PIC;22P,1mm,STRAIGHT-F, CONNECTOR-FPC/FC/PIC;5P,1.25MM,ANGLE,SN CONNECTOR-FPC/FC/PIC;5P,1.25mm,STRAIGHT, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DIODE-SWITCHING;1N4148,100V,200mA,500mW, DISPLAY-LED;GRN,6digit,8seg,46x21x17mm JACK-PIN;1P/1C,PI3.3,SN,YEL,JACK-PIN;DSPS-8805-03W,PI4,3P,GLD,COIL-PEAKING AXIAL;BAL04ST101K,-,-,-,INDUCTOR-AXIAL;33UH,5%,2.4X3.4MM TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSC945,NPN,250mW,TO-92,T TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 TR-SMALL SIGNAL;KSA643-Y,PNP,500MW,TO-92 R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON R-CARBON R-CARBON R-CARBON R-CARBON ;10K OHM,5%,1/8W,AA,T ;10K OHM,5%,1/8W,AA,T ;10K OHM,5%,1/8W,AA,T ;10K OHM,5%,1/8W,AA,T ;10K OHM,5%,1/8W,AA,T S.N.A Remark Loc.No R709 R710 R711 R712 R713 R714 R715 R716 R723 R724 R725 R726 R729 R730 R731 R732 R733 R734 R735 R737 R739 RM701 SW701 SW702 SW703 SW704 SW705 SW706 SW707 SW709 Part No 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000969 2001-000429 2001-000429 2001-000429 2001-000429 2001-000290 2001-000969 2001-000429 2001-000429 2001-000660 2001-000660 2001-000660 2001-000660 2001-000660 AC59-62001K 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165 3404-000165 3708-001163 2101-000101 Desc & Spec R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON ;10K OHM,5%,1/8W,AA,T R-CARBON;75ohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;1Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm R-CARBON;33Kohm,5%,1/8W,AA,TP,1.8x3.2mm MODULE-REMOCON;TSOP1238RF1,38KHz,-,-,-,SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S SWITCH-TACT;12V,50mA,160gf+-50gf,6x6mm,S ASSY-SHUTTLE S.N.A CONNECTOR-FPC/FC/PIC;5P,1.25mm,STRAIGHT, VR-ROTARY;100Kohm,20%,1/10W,SIDE Remark

MULTI NORMAL NORMAL NORMAL MULTI NORMAL NORMAL NORMAL MULTI NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL MULTI NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL MULTI NORMAL NORMAL MULTI NORMAL MULTI NORMAL MULTI NORMAL NORMAL NORMAL MULTI NORMAL NORMAL NORMAL MULTI NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL NORMAL

8. Block Diagrams

Page 8-1 8-2 8-3 Overall Block Diagram - - - - - - - - - - - - - - - - - - - - 8-2 System Control - - - - - - - - - - - - - - - - - - - - - - - - - 8-3 Video - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 8-4

Block Diagrams

Overall Block Diagram

System Control

9. PCB Diagrams
Page 9-1 9-2 9-3 Main - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-2
SUB (SV-415F/410F/215F/210F Only) - - - - - - - - - - - - - - - - - 9-4 Function-Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 9-4

PCB Diagrams

SUB (SV415F/410F/215F/210F Only)

Function-Timer

10. Wiring Diagram

11. Schematic Diagrams

Page 3 Block Identification of Main PCB - - - - - - - - - - - - - - - - - - - - - - - - - - 11-2 11-1 11-2 11-3 11-4 11-5 11-6 11-7 11-8 11-9 11-10 11-11 11-12 S.M.P.S/Power - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-3 System Control/Servo - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-4 Audio/Video (4 Head) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-5 Audio/Video (2 Head) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-6 IF - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-7 I/O - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-8 SECAM (SV-415F/410F/215F/210F Only) - - - - - - - - - - - - - - - - - 11-9 SUB (L. MONO ; SV-415F/410F/215F/210F Only) - - - - - - - - - - - 11-10 VPS/PDC - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-11
Function-Timer - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-12 Remote-Control (Normal) - - - - - - - - - - - - - - - - - - - - - - - - - 11-13
Remote-Control (Multi) - - - - - - - - - - - - - - - - - - - - - - - - - - - - 11-14

Schematic Diagrams

For schematic Diagram - Resistors are in ohms, 1/8W unless otherwise noted. - Circled numbers refer to waveforms. Special note : Most semiconductor devices are electrostatically sensitive and therefore require the special handling techniques described under the electrostatically sensitive (ES) devices section of this service manual. Note : Do not use the part number shown on this drawing for ordering. The correct part number is shown in the parts list (may be slightly different or amended since this drawing was prepared). Important safety notices : Components identified with the mark components. Use only the same type.

have the special characteristics for safety. When replacing any of these
3 Block Identification of Main PCB

(OPTION)

(Component Side)

(Conductor Side)

S.M.P.S/POWER

Hi-Fi OPTION

System Control/Servo

Audio/Video (4 Head)

Audio/Video (2 Head)

FRANCE OPTION

L. MONO
SECAM (SV-415F/410F/215F/210F Only)
SUB (L. MONO ; SV-415F/410F/215F/210F Only)

VPS/PDC

Remote-Control (Normal)

Remote-Control (Multi)