Use as thick a power supply cable as possible to minimize drop in voltage. Keep cables of 100 VAC and 24 VDC sufficiently away from high-voltage, large-current carrying cables. Be sure to attach the terminal cover to the terminal block. - For UG330: Attach the terminal cover (supplied) to the terminal block.

Terminal cover

- For UG430/UG530: When closing the terminal cover, hold one end of the cover as shown below.

Press either end.

Notes on Usage of 100-240 VAC Specifications
Generally, an isolating transformer improves noise resistance. However, if the display unit is far away from the secondary port of the transformer and noise gets mixed in, an isolating transformer becomes unnecessary. If any power voltage fluctuation caused by noise is expected, it is recommended that a voltage stabilizer (effective in noise resistance) be used.
Power supply Insulation transformer or Stabilized transformer

To UG430/UG530

1.25 mm2 Twist the cables.

Grounding

Be sure to establish a ground of POD. (The level of grounding resistance should be less than 100.)
An independent earth pole must be used for POD. Use a cable which has a nominal cross section of more than 2 mm2 for grounding. Set the grounding point near the POD to shorten the distance of grounding cables.

POD unit

Other equipment
* When the POD unit is attached to the mounting panel, the fixtures and frame grounds (FG) are connected. To detach the FG terminal from the ground, attach the insulating sheet to the fixtures and the mounting panel for insulation.
9. Coin-type Lithium Battery
Coin-type Lithium Battery
Be sure to set the battery when using the calendar function or the SRAM cassette. Without a battery, the contents in the SRAM or calendar data will not be retained.
Battery Mounting Procedure
Electric shock hazard Steps 2 to 5 must be performed while the power is not supplied to the POD unit.
1. A coin-type lithium battery is attached to the battery holder without connection in the backside of the unit before delivery. 2. Turn the unit off. Open the battery holder cover. To open the cover, press the end of the cover in the direction of the arrow as shown in the left illustration below.

When using the LAN port, keep the LAN cable away from the power supply cable as much as possible.

UTP cable Straight

UTP cable Straight or cross cable (For more information, refer the HUB specifications.)

UG03I-E

Ethernet unit

UG30 (standard)

(highperformance)
Distance between the node and the HUB: Maximum network nodes:

100 m maximum 100 sets

Cable Connection Diagram
Straight cable (with HUB)

10BASE-T RJ-458Pin 7 8

* Unshielded twist-pair cable
Cross cable (without HUB)
10BASE-T RJ-458Pin 10BASE-T RJ-458Pin 7 8

10BASE-T RJ-458Pin 8 7

Notes on Cables
Use the following recommended cable. Recommended cable (10BASE-T) Type: Twist-pair cable, category 5

14. CF Card (CF)

Recommended CF Card
CF cards in compliance with CompactFlashTM can be used. The following card is recommended.
Manufacturer Kodak SanDisk I-O Data Device KPCN-32 SDCFB-64-505 CFS-32MA Type Capacity 32 MB 64 MB 32 MB
Mounting and Dismounting the CF Card
1. The CF card interface is provided on the side of the unit. - For UG330:
2. Insert the card securely into the interface with the card backside outwards viewed from the rear of the unit as shown below.
When the card is inserted, the eject button pops out.

MJ2 PRIN TER

Card backside
3. To remove the card, press the eject button. The card pops out.
Notes on Handling the CF Card
1. Do not insert or remove the CF card during access. Doing so may destroy data on the CF card. The CF card can be inserted or removed safely when the Main Menu screen is displayed. However, if the [Card Menu] switch is pressed on the Main Menu screen and the CF card operation screen is displayed, it is not possible to insert or remove the CF card. Before mounting or removing the CF card, be sure to check that the CF card is not being accessed. 2. Do not turn the power off or on during access to the CF card. 3. Make a backup copy of the CF card at regular intervals. 4. If a disk error occurs and data read/write operation is disabled, perform a scan disk on Windows and try to restore the disk. If not restored, initialize the CF card. (For information on scan disk and Windows operations, refer to the manual for Windows.) 5. The number of writing times per CF card is limited (approx. 300,000 times). Consequently, frequent writing at short intervals may shorten service life of the CF card. To use the CF card for saving sampling data, check the setting for sampling time. Also, avoid repeated writing using a CYCLE macro command.

Solution Examine the CPU error code and solve the problem. Examine the connection between the PLCs SD (TXD) and the PODs RD (RXD). Check the type and range of memory that you set. Confirm whether or not the CPU that you are using can be used with the UG series. Check 1, 2, 3 described below. Check 1, 2, 3 described below. Check 1, 2, 3 described below. Check 1, 2, 3 described below.
Invalid memory (applicable to MITSUBISHI CPU) Invalid CPU model (applicable to MITSUBISHI CPU) Format Compare (applicable to HIDIC S10) NAK (applicable to Allen-Bradley PLC) TNS discrepant (applicable to Allen-Bradley PLC) Communication Error Count error (applicable to MITSUBISHI CPU/Q link unit) Command error (applicable to MITSUBISHI CPU/Q link unit) Invalid cassette (applicable to MITSUBISHI ACPU) Password error (applicable to MITSUBISHI QCPU)
Check 1, 2, 3 described below. Check 1, 2, 3 described below.
Check 1, 2, 3 described below.
Contact your local distributor.
Solution 1. Confirm link unit settings. (After making settings, cut power to the PLC.) 2. Go to the editor (UG00S-CW) and confirm the settings in the [Comm. Parameter] dialog in the [System Setting] menu. 3. If errors only occur from time to time, it is possible that there is a noise-based communication error.
* If you still cannot solve the error even after following the suggestions above, contact your local distributor.
Error Messages for Network Communication

Ethernet

Error Message Ethernet Error: XXXX Contents The Ethernet status is saved at system memory address $s518 and a code other than 0 (normal) is received. XXXX: Error No. Solution For the contents and solution to each error number, refer to Chapter 4 Network Communications/Error Display.

CC-LINK

Error Message I/F Board Err No. of Occupy Setting Err Contents The I/F unit for CC-LINK has an error. The number of occupy in [Comm. Parameter] is different from the number of occupy by switches. POD is about to access exceeding the set number of input/output words. The port number set by a switch is not within the setting range (1 to 64). Word writing to a special relay (M9000 and later) is attempted. (Notes: Only bit writing is possible for special relays when connecting with CC-LINK.) Solution Contact your local distributor. Check the setting of the number of occupy. Check the memory for the network I/O in the screen data file. Specify the port number within the setting range. Do not attempt to perform word writing to special relays.
Network I/O Access Err Station Number Err Word Writing to Sp. Relay

OPCN-1

Error Message I/F Board Err Stat. No. out of range Network Link Error Network I/O Access Err Waiting for Reply Contents The I/F unit for OPCN-1 has an error. The port number set by a switch is not within the setting range (1 to 127). Cannot connect to the master station in the network. POD is about to access exceeding the set number of input/output words. 1) Less than Max_int time (communication monitoring time for salve station) set on the PLC for OPCN-1 communications 2) Timeout on the UG00S-CW editor (The timeout time can be set from [System Setting] [Comm. Parameter] on the UG00S-CW editor.) This error is indicated when the above 1) and 2) are present. Word writing to a special relay (M9000 and later) is attempted. (Notes: Only bit writing is possible for special relays when connecting with OPCN-1.) Solution Contact your local distributor. Specify the port number within the setting range. Check the condition of the master station (PLC). Check the network connection. Check the memory for the network I/O in the screen data file. When the Max_int time is too long (infinite, for example) on the PLC, it is not possible to know whether or not the response from the PLC is correctly made. This error message disappears when a response from the PLC is received within the Max_int time.

POD (CN1)

Shield Signal Name Pin No. To the PLCs RS422 port

FG +SD SD +RD RD SG

Receive data (+) Receive data () Send data (+) Send data () SG

2-wire system:

SG Send/receive data (+) Send/receive data ()
For serial communications, the following settings on the UG00S-CW editor are required. The settings in the [Select PLC Type] and [Comm. Parameter] dialogs are shown on the Main Menu screen of the POD. (Refer to Chapter 2 POD Operations.)

PLC Selection

Select the PLC that is connected. Setting Position [System Setting] [PLC Type] [Select PLC Type] dialog
Communication Parameter Setting
The communication parameter setting is essential for successful communications between the POD PLC. Check the communication parameter setting on the PLC before making the setting on POD. Setting Position [System Setting] [Comm. Parameter] [Comm. Parameter] dialog Setting Items - [Connection] (1 : 1 / 1 : n / Multi-Link / Multi-Link 2) Select the type of connection between the POD and the PLC. There are four types available. Depending on the selected type, the setting items in the [Comm. Parameter] dialog or those for the memory vary. Select [1 : 1] for 1 : 1 connection. - [Local No.] Set the port number of the PLC. - [Trans. Mode] (Trans. Mode 1/Trans. Mode 4) When the PLC has a transmission mode setting, set the same on the POD. (This setting must be used for PLCs of MITSUBISHI, OMRON, HITACHI, YOKOGAWA, Toyoda Machinery and YASKAWA.) - [Baud Rate] [Signal Level] [Data Length] [Stop Bit] [Parity] Make the same setting as the PLC. (Refer to Chapter 5 Connection to PLCs.) [Baud Rate] (4800, 9600, 19200, 38400, 57600, 76800, 115 kbps) Set the same communication speed as the PLC. [Signal Level] (RS232C/RS422) Set the same communication interface as the PLC. [Data Length] (7-bit/8-bit) Choose either data length for communication. [Stop Bit] (1-bit/2-bit) Choose either stop bit for communication. [Parity] (None/Odd/Even) Choose any of the parity options for communication. - [Send Delay Time] (0 to 255) (Unit: 1 msec) Set a time delay in sending the next command to the PLC after receipt of a response from the PLC. Normally use the default setting.

POD Send delay time t

- [Start Time] Set a time delay in seconds in starting communications on the POD to avoid a delay in PLC processing that may occur when the POD and the PLC are turned on at the same time.
- Choose the action to be taken against communication errors. [Comm. Error Handling] Set error handling routine in the case that a communication error between the POD and the PLC occurs. [Stop] If any communication error has arisen, the communications are stopped. When restoring, use the Retry switch (found on the error screen of the POD).

UG30C-M

1 : 1 connection cable (RS-232C, RS-485/RS-422)
With RS-485 (2-wire connection), a maximum of 31 PLCs can be connected. For information on connection between PLCs, refer to the instruction manual for the PLC.
Connecting method 2 (using UG00C-B or UG00C-H)
Use Fuji Electrics cables when connecting the POD to a PLC at the MJ port. For connection via RS-232C interface, use UG00C-B; for connection via RS-485 interface, use UG00C-H. The shielded frame ground of the cable must be connected to the POD.
* Notes on Use of UG00C-B There are four wires in the UG00C-B cable as shown on the right. The wires to be used are determined depending on the connecting method. For the wires not used, be sure to properly insulate with tape, etc. UG00C-B Brown Red Orange Yellow
<RS-232C Connection> Connection example with MITSUBISHI A1SJ71UC24-R2

POD Modular jack, 8-pin

FG SD(Yellow) RD(Orange) SG(Red) 5
PLC D-sub 9pin(Male: ) D-sub 9-pin (male)

CD RD SD SG DR RS

* Use the shielded cable.
<RS-485 Connection> Connection example with MITSUBISHI A1SJ71UC24-R4 (1 set)
FG +SD/RD (Black) SD/RD (Green) SG

SDA SDB RDA RDB SG

Connection example with MITSUBISHI A1SJ71UC24-R4 (3 set)

FG 5 SDA SDB RDA RDB SG

* Use the shielded cable. Terminating * Use shielded resistance twist-pair cables. (ON)

FG SDA SDB RDA RDB SG

Terminating resistance (OFF) * Use shielded twist-pair cables.
The terminating resistance of the POD should be set on the DIP switch in the backside of the unit. When MJ1 is used: Set DIPSW6 to the ON position. When MJ2 is used: Set DIPSW8 to the ON position.
UG00S-CW Setting System Setting
PLC model selection and parameter setting to be made on the UG00S-CW editor for the PLC2Way connection at the MJ port are explained.
Temp. CTRL/PLC2Way Setting
Select the PLC model and make the parameter setting as described below. 1. Select [System Setting] [Temp. CTRL/PLC2Way Setting] [Temp. CTRL/PLC2Way Comm. Setting]. The [Temp. Control/PLC2Way Comm. Setting] dialog is displayed.
2. Check [Use Temp. Control Network/PLC2Way Communication].
3. Select the MJ port. Click the [Refer to Modular] button. The [Modular Jack] dialog is displayed. Select [Temp./PLC2Way] for modular jack 1 or 2 that is used for PLC2Way communication.
4. Select the PLC model to be connected at the MJ port. Click the [Setting] button. The [Type Setting] dialog is displayed. Select [PLC2Way]. The PLC manufacturer names who support PLC2Way communication are displayed. Click [+]. The available model names of the selected manufacturer are displayed. Select the PLC model name and click [OK]. The message communication Communication parameters are reset. OK? is displayed. Click [Yes]. 5. Set the parameters for the PLC to be connected at the MJ port.

Execution of macro a

POD communication cycle
Temperature control network/ PLC2Way table periodical reading
TEMP_CTL $uTEMP_CTL $uTEMP_CTL $u120 2
Temperature control network/PLC2Way table periodical reading

TEMP_CTL $u300 2

(Fig. b)

Execution of macro b

$s762=1 TEMP_CTL $uTEMP_CTL $uTEMP_CTL $u120 2

TEMP_CTL $u$s762=0

$s763 Forced execution of macro commands [TEMP_READ] and [TEMP_WRITE] using the temperature control network/PLC2Way table - [0]: When any station that has failed is included in the specified table, the macro command is not executed. - [Other than 0]: The macro command is forcibly executed to the stations that are working properly.
8. Temperature Control Network
Temperature Control Network
Using the temperature control network, the POD can be connected to the temperature controller. With RS-232C, one PLC can be connected; with RS-485, a maximum of 31 temperature controllers can be connected.

Temperature controller

SET/ENT

AL1 OUT

n (Max = 31)
Data of temperature controllers connected to the POD can be set or monitored. Periodical reading/sampling of temperature controller data Temperature controller data can be read into the PLC memory or POD internal memory at regular intervals using the temperature control network table. It is also possible to save the read data in the POD internal buffer, SRAM or CF card. Data transfer It is also possible to transfer data in the PLC memory, POD internal memory or a memory card to the temperature controller at one time using a macro command. Conversely, data in the temperature controller can be transferred to the PLC memory, POD internal memory or a memory card at one time. For more information on compatible temperature controllers and the required settings, refer to Users Manual <Temperature Control Network> (FEH365).
1. 2. 3. 4. 5. 6. 7. Ethernet FL-net (OPCN-2) CC-Link OPCN-1 T-LINK PROFIBUS-DP SX-BUS

EREAD:

Read into memory

EREAD F0 = F1 C: F2 F3

Example: Macro command at the POD (A) The macro command for POD (A) to read data from PLC (B) and transfer it to PLC (A) is shown below. [Description] EREAD D200 = D100 C: 2 B
Address of the source (Network table number)
Top memory address of the source Top memory address of the target
The number of words to be transferred

[Contents]

Two words starting from D100 in PLC (B) are read into D200 in PLC (A).
<POD (A)> <V7: A>
<PODB> <V7: (B)>

D200 - 201

D100 - 101
<PLC (A)> <PLC: A>
<PLC (B)> <PLC: B>
[EWRITE] Words from the F2 memory are written into the F0 memory in the POD of the network table number specified for F1. F3 designates the number of words to be written. Usable Devices
Internal Memory F0 F1 F2 F3 PLC Memory Constant Memory Card Indirect Designation Doubleword IP Address

EWRITE: Write to memory

EWRITE F0 F1 = F2 C: F3
Example: Macro command at the POD (A) The macro command for POD (A) to write data in POD (A) to PLC (B) is shown below. [Description] EWRITE D100 B = $u100 C: 2
The number of words to be transferred Top memory address of the source
Address of the target (Network table number)
Top memory address of the target
Two words starting from $u100 in POD (A) are written into D100 in PLC (B).

$u100 - 101

SYSTEM SYSTEM F1
<POD (A)> <V7:A>

EWRITE

<POD (B)> <V7:B>

run stop

<PLC (A)> <PLC:A>
D100 - 101 <PLC (B)> <PLC:B>
[SEND] Words from the F0 memory are transferred to the server of the network table number specified for F2. F1 designates the number of words to be transferred. Usable Devices
Internal Memory F0 F1 F2 PLC Memory Constant Memory Card Indirect Designation Doubleword IP Address

Send to server

SEND F0 C: F1 TO: F2
Example: Macro command at the POD (B) The macro command for POD (B) to transfer data to server (A) is shown below. [Description] SEND $u100 C: 2 TO: A

The number of words to be transferred Top memory address of the source Address of the target (Network table number)
Two words starting from $u100 in POD (B) are transferred to server (A).

Server (A)

<PLC (B)> <PLC:B>
The Ethernet status is output to the system memory ($s) of the POD. This section explains the memory addresses ($s514 to 619) where the Ethernet status is output. For other memory addresses, refer to the Users Manual <Function> (FEH376).
Contents Macro user request wait (0: absent 1: present) Result of executing the macro user request wait
Ethernet status Network table 0 status Network table 1 status Network table 2 status Network table 3 status Network table 4 status Network table 5 status Network table 6 status Network table 7 status Network table 8 status Network table 9 status Network table 10 status Network table 11 status Network table 12 status Network table 13 status Network table 14 status Network table 15 status Network table 16 status Network table 17 status Network table 18 status Network table 19 status Network table 20 status Network table 21 status Network table 22 status Network table 23 status Network table 24 status Network table 25 status Network table 26 status Network table 27 status Network table 28 status
Address $sNetwork table 29 status Network table 30 status Network table 31 status Network table 32 status Network table 33 status Network table 34 status Network table 35 status Network table 36 status Network table 37 status Network table 38 status Network table 39 status Network table 40 status Network table 41 status Network table 42 status Network table 43 status Network table 44 status Network table 45 status Network table 46 status Network table 47 status Network table 48 status Network table 49 status Network table 50 status Network table 51 status Network table 52 status Network table 53 status Network table 54 status Network table 55 status Network table 56 status Network table 57 status Network table 58 status Network table 59 status Network table 60 status Network table 61 status Network table 62 status Network table 63 status Network table 64 status Network table 65 status Network table 66 status Network table 67 status Network table 68 status Network table 69 status Network table 70 status Network table 71 status Network table 72 status
Address $s619 Network table 73 status Network table 74 status Network table 75 status Network table 76 status Network table 77 status Network table 78 status Network table 79 status Network table 80 status Network table 81 status Network table 82 status Network table 83 status Network table 84 status Network table 85 status Network table 86 status Network table 87 status Network table 88 status Network table 89 status Network table 90 status Network table 91 status Network table 92 status Network table 93 status Network table 94 status Network table 95 status Network table 96 status Network table 97 status Network table 98 status Network table 99 status

Page 4-40

Others
Initialization function Receive wait from POD Cancel receive wait function Request connection information Close processing Get sources IP Address Get error contents int HKEtn_Init(unsigned short Port=10000,int Retry=3,int RecvTime=2,int RecvTime2=10) int HKEtn_Recvfrom(BYTE *dp,short *lpCnt) void HKEtn_Cancel(void) int HKEtn_GetInf(struct inf *lpinf,char *lpAddr) int HKEtn_Close() int HKEtn_GetSinAddr(char *lpAddr) int HKEtn_GetLastError() Page 4-43 Page 4-41 Page 4-41
Read Words from PLC Memory
int HKEtn_ReadPlcMemory(WORD *dp,unsigned short Wordcnt,int DeviceType,DWORD addr,char *lpAddr, int DFlag=1) This function is retained until PLC data is transferred from the POD. Parameters *dp Target pointer of the data to be read

Contents No. 1 No. 2

Word Count 1 1

Wordcnt DeviceType addr

*lpAddr DFlag Return values Success Failure Error details
Word count to be read (max. 2000 words) Address of the device to be read (Refer to Chapter 5 Connection to PLCs.) Top memory address to be read For YOKOGAWA or YASKAWA PLCs, specify a number 1 for the address (addr). Example: DDIP address shown as a string of characters separated by dots Example: 192.168.XXX.XXX 0, 1, 2 (Refer to the table below.) TRUE FALSE Get using HKEtn_GetLastError ().
Priority and communication procedure depending on the DFlag setting are shown below.

DFlag Priority

PC Read/write request Response Acknowledge of completion

Communication Procedure

POD PLC Memory card

Communications

Display
POD Read/write request Acknowledge of completion

PLC Memory card

Read Double-words from PLC Memory
int HKEtn_ReadPlcMemory2(DWORD *dp,unsigned short Wordcnt,int DeviceType,DWORD addr,char *lpAddr, int DFlag=1) This function is retained until PLC data is transferred from the POD. Parameters *dp Target pointer of the data to be read

Word Count 2 2

Word count to be read (max. 1000 words) Address of the device to be read (Refer to Chapter 5 Connection to PLCs.) Top memory address to be read For YOKOGAWA or YASKAWA PLCs, specify a number 1 for the address (addr). Example: DDIP address shown as a string of characters separated by dots Example: 192.168.XXX.XXX 0, 1, 2 (Refer to page 4-29.) TRUE FALSE Get using HKEtn_GetLastError ().
Read Words from Internal Memory
int HKEtn_ReadInternalMemory(WORD *dp,unsigned short Wordcnt,int DeviceType,DWORD addr,char *lpAddr,int DFlag=1) This function is retained until data is transferred from the POD. Parameters *dp Target block pointer
Wordcnt DeviceType addr *lpAddr DFlag Return values Success Failure Error details
Word count to be transferred (max. 2000 words) 0: $u 1: $s Top memory address to be read IP address shown as a string of characters separated by dots Example: 192.168.XXX.XXX 0, 1, 2 (Refer to page 4-29.) TRUE FALSE Get using HKEtn_GetLastError ().

TCP connection over

TCP connection error

TCP connection end error

1100 - 1301 1302
TCP send error Send buffer full IC receive buffer overflow Driver receive buffer overflow Receive processing error, link down error Transceiver error No IP address at local port Duplicated IP address error Send socket ID error (error that may occur when UG30 (high-performance type) LAN port is used) Ethernet I/F unit not mounted Ethernet I/F unit not ready Ethernet I/F unit DPRAM error No response from Ethernet I/F unit Ethernet receive buffer over Ethernet send registration error I/F unit unregistered interrupt Initialization error (communication unit) Dual port access error Undefined register Send/receive buffer area over MAC address error Port error Watch dog overflow JAVA error LANC error
Check whether the Ethernet I/F unit is mounted correctly, and then turn the power off and on. If the problem persists, contact your local distributor.
Errors during Macro Command Execution
The execution result of macro commands SEND/EREAD/EWRITE is stored in system memory address $s515. System memory address: $s515 (response to the request)
Code - Normal Communication error Timeout The number of words being sent exceeds the limit. Specified table not used Cannot use the send command. Specified table being used Cannot process due to short memory Illegal receive packet bytes Memory access error Macro setting error Refer to Communication Errors. Check if an error is occurring to the target POD. Check the number of words that can be sent in macro editing. Check the setting on the network table. Check the macro command in macro editing. Contents Solution
Check that system memory address $s514 is set. If not, reduce the frequency of communications. Check the memory space at the target station. Check the requested number of words. Check the setting of the requested memory. Check the macro setting.

2. FL-net (OPCN-2)

FL-net (OPCN-2)
FL-net (OPCN-2) is an open FA network that Foundation of the Manufacturing Science and Technology Center has standardized as a netowork on the controllers level, and enables to connect with multi-vendor devices such as programmable controllers, NC controllers and robots etc. It is possible to connect FA controllers and computers, such as programmable controllers (PLCs) or NC controllers (CNCs), of different manufacturers as shown below for control and monitoring

Ferrite core POD A/QnA series CPU
Recommended ferrite core type: TDKs ZCAT2032-0930 (ID: 8 mm, OD: 20 mm) In consideration of such noise problems, it is recommended that the standard type link unit be used when the cable length of 15 m or longer is required. Wiring Diagram 8

RDA SDA SG RDB SDB

A Link + Net10
When the POD is connected to the standard type link unit on the CPU that is connected to the data link system or network system, the POD can have access to CPUs on NET II (/B) and NET/10. In this case, select A Link + Net10 for [PLC Type] on the UG00S-CW editor. When the POD has access to the CPU on NET II (/B) or NET/10: - With NET II (/B), the POD can only have access to CPUs in the network of the CPU equipped with the standard type link unit that is connected to the POD. (Available CPU No. 0 to 30) - With NET/10, the POD can have access to CPUs in the network (No. 1 in the illustration below) of the CPU equipped with the standard type link unit that is connected to the POD as well as those in the other networks (Nos. 2 and 3 in the illustration below) that are connected. (Available CPU No. 1 to 30)

Standard type link unit

POD CPU (1-1) CPU (1-5) CPU (1-2) (2-2) CPU (2-1) CPU (2-5)

Network No. 1

CPU (1-4)

Network No. 2

CPU (2-4)
CPU (1-3) CPU (3-2) (2-4)

CPU (2-3) (3-1)

Network No. 3

CPU (3-3) CPU (3-4)

CPU (3-5)
When the POD reads from or writes to the CPU (1-1 in the above illustration) equipped with the standard type link unit: Set 31 for [CPU No.] for memory setting on the UG00S-CW editor. The response time is the same as that with 1 : 1 connection between the POD and the PLC. When the POD reads from or writes to the CPU memory of the CPU number other than 31: Transient transmission is performed and the response time is not fast. Please understand beforehand.
To have access to the PLC in the other network on NET/10, specify the network number in the OPEN macro for the screen on the UG00S-CW editor. This macro command should be [OUT_ENQ] of system call [SYS]. It is not possible to have access to the CPU on the different network from the same screen. Network specifying macro [OUT_ENQ] of system call [SYS] F1 memory

HIDIC-S10/ABS

Memory 0E 19 1A 1B 1C 1D TYPE Remarks

FG SD RD CS SG

SD RD RS CS DR PHL SG

CD RD SD ER SG DR RS

TxDP TxDN RxDP RxDN
Wiring Diagram 5 When connecting to the S10x series, add a resistor of 50 (1/2 W) as shown below.

FG +SD -SD +RD -RD

UTX H UTX L URX H URX L

5. MATSUSHITA PLC

MATSUSHITA PLC
Select PLC Type PLC FP1 FP3 FP5 FP10 AFP3462 AFP3463 AFP5462 RS-232C tool port on the CPU unit AFP5462 RS-232C port on the CPU unit MEWNET FP10S AFP3462 AFP3463 FP0 RS-232C tool port on the CPU unit RS-232C port on the CPU unit FP2 RS-232C tool port on the CPU unit RS-232C port on the CPU unit Unit/Port RS-232C port on the CPU unit RS-232C RS-232C RS-422 RS-232C RS-232C RS-232C RS-232C RS-232C RS-422 Connection [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 4] [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 4]
MATSUSHITAs RS-232C cable AFC8513 RS-232C [Wiring Diagram 3] MATSUSHITAs RS-232C cable AFC8513 RS-232C [Wiring Diagram 2]
Item Baud rate Port Parity Transmission code Data bit Stop bit Setting on PLC 19200 bps [0] 10, [1] 1 Even 7 (ASCII) 1 Computer link function (fixed) Invalid (fixed) POD Comm. Parameter Setting 19200 bps 1 Even
Transmission mode Control signal
* If a tool port (the ladder port for RS-232C) is used, the range of PLC parameter setting is limited as below. Adjust the PLC parameter setting to communication parameter setting of the POD. Baud rate: 9600, 19200 bps (115 kbps available with FP2) Parity: Odd (fixed) Data bit: 8 (or 7, select 8 normally) Stop bit: 1 (fixed)
MEWNET: Link Unit Switch Setting
Switch Setting ON OFF OFF OFF ON ON OFF OFF Data length: 7 bits With parity Even Stop bit 1 CS, CD invalid Same as that set on POD (normally 19200 bps) Contents
Memory DT X Y R L LD FL SV EV T C (data register) (external input relay) (external output relay) (internal relay) (link relay) (link register) (file register) (timer/counter set value) (timer/counter elapsed time) (timer/contact) (counter/contact) TYPE 10 Read only Read only WX as word device, read only WY as word device WR as word device, including special relays WL as word device Remarks

SD RD RS CS SG CD

PLC +

6. YOKOGAWA PLC

YOKOGAWA PLC
Select PLC Type FA500 CPU FA500 Unit/Port LC01-0N LC02-0N Programming tool port on the CPU module*1 FA-M3 FA-M3 F3LC01-1N*2 F3LC11-1N F3LC11-2N FA-M3R FA-M3 R Programming tool port on the CPU module*1 F3LC12-1F RS-232C RS-232C RS-422 Connection [Wiring Diagram 1] [Wiring Diagram 1] [Wiring Diagram 3] PLC2Way

Item Baud rate Connection Parity Transmission code Data length Stop bit Setting on PLC 9600 bps Odd 8 (fixed) 1 POD Comm. Parameter Setting 9600 bps Multi-Link (fixed) Odd 8 1
Memory MW KW M (memory word) (constant word) (bit memory) TYPE 2 Remarks

MiniDIN 9-pin (male)

29. Automationdirect PLC
Select PLC Type D4-430 D4-440 Direct LOGIC D4-450 D2-240 D2-250 D4-430 D4-440 Port 1 on a CPU unit Port 0 on a CPU unit Port 3 on a CPU unit Port 2 on a CPU unit D2-240 D2-250 Port 1 on a CPU unit Port 2 on a CPU unit Port 1 on a CPU unit Port 2 on a CPU unit RS-232C [Wiring Diagram 3] RS-232C [Wiring Diagram 2] RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 5] RS-232C [Wiring Diagram 4] RS-485 [Wiring Diagram 6] Port 1 on a CPU unit Port 3 on a CPU unit Port 2 on a CPU unit Port 2 on a CPU unit Port 2 on a CPU unit RS-232C [Wiring Diagram 1] RS-422 [Wiring Diagram 5] RS-485 [Wiring Diagram 6] PLC Unit/Port Connection
RS-232C [Wiring Diagram 2] RS-232C [Wiring Diagram 3]
D4-450 Direct LOGIC (K-Sequence)
Item Baud rate Port Parity Transmission code Function Response delay time Time-out ASCII/HEX Data length Stop bit Setting on PLC 19200 bps 0 for 10, 1 for 1 Odd Host link system (fixed) 0 (fixed) None (fixed) HEX (fixed) POD Comm. Parameter Setting 19200 bps 1 Odd
Memory V X Y C S GX GY T CT (data register) (input relay) (output relay) (internal relay) (stage) (global inputs) (global outputs) (timer/contact) (counter/contact) TYPE 8 Remarks

Modular connector 6-pin

SG RxD TxD

654321

* Use shielded twist-pair cables. *1 High density D-sub 15-pin
PLC *1 D-sub 15-pin (male)

TXD RXD 0V

In case SU-6M, it is possible to use terminal blocks,

30. VIGOR

Select PLC Type M series PLC M1-CPU1 Unit/Port COM PORT Connection RS-232C [Wiring Diagram 1] RS-485 [Wiring Diagram 2]
The recommended communication parameter settings of the PLC and the POD series is as follows:
Item Baud rate Port Parity Transmission code Data length Stop bit Setting on PLC 19200 bps 0 Even POD Comm. Parameter Setting 19200 bps 0 Even 7 1
Memory D X Y M S T C 32C TS CS TC CC (data register/special register) (input relay) (output relay) (internal relay/special relay) (internal relay/step relay) (timer/current value) (counter/current value) (high-speed counter/current value) (timer/contact) (counter/contact) (timer/coil) (counter/coil) TYPE *1 Remarks

Art.Nr. 110DAF-05A

Art.Nr. 111DAF-05

with ABE

Art.Nr. 112DAF-05W-2

w ith A BE

Art.Nr. 110DAF-05A-2

Art.Nr. 112DAF-05W-1

Centre table DAF Art.Nr. 111DAF-05-2 series XF 105 Also for 95 XF, XF 95 (from const. year 9/97) incl. non slip mat. Suitable from Toll system equipment forSiemens/Grundig, when they are mounted On the left of the middle console. Walnutdesign Art.Nr. 112DAF-05W-2 black/grey Art.Nr. 111DAF-05-2 Aluminiumdesign Art.Nr. 110DAF-05A-2
Centre table DAF series XF 105 Also for 95 XF, XF 95 (from const. year 9/97) incl. non slip mat. Suitable for toll system equipment from Grundig, when this is mounted in the centre of the cab Walnutdesign Art.Nr. 112DAF-05W-1 black/grey Art.Nr. 111DAF-05-1 Aluminiumdesign Art.Nr. 110DAF-05A-1
Art.Nr. 111DAF-05-1 Art.Nr. 110DAF-05A-1
Wurzelholzdesign Art.Nr. 112DAF-11W Schwarz / grau Art.Nr. 111DAF-11 Aluminiumdesign Art.Nr. 110DAF-11A

Art.Nr. 112DAF-12W

Passenger table DAF series XF 105 Incl. non slip mat. Suitable for DAF-05 !!!
Walnutdesign black / grey Aluminiumdesign Art.Nr. 112DAF-12W Art.Nr. 111DAF-12 Art.Nr. 110DAF-12A

Art.Nr. 112DAF-11W

Passenger table DAF series XF 105 Incl. non slip mat. Doesnt fit with DAF-05 !!!
Art.Nr. 111DAF-11 with ABE
Art.Nr. 110DAF-11A with ABE

Art.Nr. 111DAF-12

Art.Nr. 110DAF-12A

Walnut/black

Coffee machine holders DAF XF 105
Storage above the motortunnel! Holder for Kirk coffee machine (6 cups). Incl. non slip mat. !Without coffee machine! Walnut/black Art.Nr. 112DAF-13W Black/grey Art.Nr. 111DAF-13 Aluminium/grey Art.Nr. 110DAF-13A
Kirk-Electronic-coffee machine 6 cups

Art.Nr. 25309010001

Black/grey

Aluminium/grey

Centre table for DAF 95 XF, XF 95 und XF 105
from model 9/97. Incl. non-slip mat, with fitting for Kirk-coffee-maker. !Without coffee machine! Walnut/black Art. Nr. 112DAF-14W Black/grey Art. Nr. 111DAF-14 Aluminiumdesign Art. Nr. 110DAF-14A
from model 9/97. Incl. non-slip mat, for Grundig toll unit when fitted in the center of the vehicle, with fitting for Kirk-coffee-maker. !Without coffee machine! Walnut/black Art. Nr. 112DAF-14W-1 Black/grey Art. Nr. 111DAF-14-1 Aluminiumdesign Art. Nr. 110DAF-14A-1

(without pic.)

from model 9/97. Incl. non-slip mat, for Siemens/Grundig toll unit when fitted on the right side next to the center console- with fitting for Kirk-coffee-maker. !Without coffee machine! Walnut/black Art. Nr. 112DAF-14W-2 Black/grey Art. Nr. 111DAF-14-2 Aluminiumdesign Art. Nr. 110DAF-14A-2
Sensible, practical built in furniture from MARLEN
DAF 95 XF/XF95 Super Space Cab Built in cabinet rear, 3-door, replaces upper bed in Walnutdesign Art. Nr. 11504ES17W in black Leatherdesign Art. Nr. 11504ES17S in light grey Leatherdesign Art. Nr. 11504ES17G in Aluminiumdesign Art. Nr. 11504ES17A
DAF XF95/XF105 Space Cab Built in cabinet rear, in noble Walnutdesign.with 3 spacious compartments. Replaces the upper bed in Walnutdesign Art. Nr. 11504ES18W in black Leatherdesign Art. Nr. 11504ES18S in light grey Leatherdesign Art. Nr. 11504ES18G Walnut screens DAF 95 XF Space Cab 3 piece Set, screens in Walnutdesign for the storage compartments above the windscreen Art. Nr. 11904BLEW02
Walnut screen DAF 95 XF Super Space Cab Screens are installed onto the storage box flaps by means of enclosed screws. 3-piece Art. Nr. 11904BLEW01
Bed under body cabinet for DAF 95 XF Space Cab & Super Space Cab optional with a drawer and a 35L. Compressor fridge or with two drawers. Design with 2 drawers: in Walnutdesign Art. Nr. 11504BU03W in black Leatherdesign Art. Nr. 11504BU03S in light grey Leatherdesign Art. Nr. 11504BU03G in Aluminiumdesign Art. Nr. 11504BU03A Built in cabinet with 3 doors for Daf CF models (only Space Cab)
replaces the upper bed. Equipped to fit a TV and microwave
Photo left: Special construction: On customer's request the rear wall and the side panels of the cab can also be fitted with Walnut decoration.
in Walnutdesign in black Leatherdesign in light grey Leatherdesign in Aluminiumdesign
Art. Nr. 11504ES23W Art. Nr. 11504ES23S Art. Nr. 11504ES23G Art. Nr. 11504ES23A
Bed under body for DAF CF Super Space & Sleeper Cab

Bed under body, optional with a drawer and a 35L. Compressor fridge or with 2 drawers. Design with 2 drawers:
Art. Nr. 11504BU13W Art. Nr. 11504BU13S Art. Nr. 11504BU13G Art. Nr. 11504BU13A

Art. Nr. 25309020016.4

35 l. fridge (with clamp lock)
35L. fridge (with clamp lock)
For the construction of a 35 litre refrigerator add the letters KS to the end of the Art. No.
Trays and passenger tables from MarLen for your DAF

Wi BE th A

Art. Nr. 111DAF-05
E Driver tables are also AB ith available with an excerpt W for a toll system from Grundig and Siemens. Therefore the article number must be with a -1 for Grundig and a -2 for Siemens on the end. For pictures see page 4

Art. Nr. 112DAF-05W

Art. Nr. 111DAF-06
Centre table for DAF 95XF, XF95 and XF105 and passenger table for DAF 95XF, XF95 Centre table: Walnutdesign Art. Nr. 112DAF-05W black Leatherdesign Art. Nr. 111DAF-05 in Aluminiumdesign Art. Nr. 110DAF-05A Passenger table: Walnutdesign Black Leatherdesign in Aluminiumdesign
Art. Nr. 112DAF-06W Art. Nr. 111DAF-06 Art. Nr. 110DAF-06A

Art. Nr. 112DAF-06W

With ABE
(Not suitable in connection with centre table DAF-05)

Passenger table large

Walnutdesign black Leatherdesign Aluminiumdesign
Art. Nr. 112DAF-04W Art. Nr. 111DAF-04 Art. Nr. 110DAF-04A

Art. Nr. 111DAF-08

BE th A i

Art. Nr. 112DAF-08W

Art. Nr. 112DAF-04W
Centre table for DAF CF 65/75/85
Walnutdesign black Leatherdesign

(Without pic.)

Art. Nr. 112DAF-08W Art. Nr. 111DAF-08

Art. Nr. 110DAF-08A

Art. Nr. 111DAF-09
Passenger table for DAF CF 65/75/85 Walnutdesign Art. Nr. 112DAF-09W black Leatherdesign Art. Nr. 111DAF-09 Aluminiumdesign Art. Nr. 110DAF-09A

Art. Nr. 112DAF-09W

Art. Nr. 112DAF-07W

Art. Nr. 111DAF-07

Centre table for DAF 65/75/85 old model in Walnutdesign Art. Nr. 112DAF-02W Art. Nr. 111DAF-02 in black Leatherdesign
Centre table for DAF LF from const. year May 2001 Walnutdesign Art. Nr. 112DAF-07W black Leatherdesign Art. Nr. 111DAF-07 Aluminiumdesign Art. Nr. 110DAF-07A

Velours articles Also available for your DAF XF 105 !

Silver grey 203

Black 577
Cool fridges - thats how everything stays fresh
Pic. 1: Compressor fridge 50 Liter Suitable for MarLen bed under body -12/24V - W:439xH:400xD:705mm Art. Nr. 25309020004 Pic. 2: Compressor coolbox CD-030DC 30L - W 440 H 250 D 730 mm 12&24V Art. Nr. 25309020017.1 Mounting kit Art. Nr. 25309020017.2

Pic. 1

Pic. 2
Pic. 4:CoolMatic CS-Compressor coolbox 37L, 26L, normal cooling, 11L deep cooling, 12/24V, 45W, temperature field +10 till -12, 2 separate drawers, inner lighting, Danfoss compressor, under voltage protection. Art. Nr. 25309020026 Pic. 5: Coolbox Coolmatic CDF 35 content 31L., W 340 x H 380 x D 560mm 12/24V Art. Nr. 25309020022 Pic. 6: Coolbox Coolmatic CF 35 content 31L., W 340 x H 380 x D 560mm 12/24V Art. Nr. 25309020015 Pic. 7: Tropicool Classic TC-21 FL Content 21L., B303x H420x T450mm 12/24V Art. Nr. 25309020030.1 Pic. 8: Coolbox Coolmatic CF 50 content 50 litre, 12-24V-DC / 110-240V AC, temperature field 10 C till -18 C, ,medium power consumption 45W W 630 x H 480 x D 360mm, weight approx 18 kg. Included in delivery: DC & AC connector cable, removable wire basket, mountable carry handles, Inner lighting. Art. Nr. 25309020021 Pic. 9: Compressor coolbox C47L With drawer and partition rail -12/24V DC 47L, W:430 H:370 D:686 mm. Cooling +10 C - 0 C. Art.Nr. 2530900004 Pic. 10: Under body fridge for bed under body 35L. Compressor fridge with drawer, clamp lock, connection voltage 12 / 24 Volt, Power consumption 42 Watt, Under voltage protection, Thermostat regulator, W 440 x H 250 x D 720mm. Art. Nr. 25309020016.4
Screen Walnutdesign for 35L. fridge Art. Nr.11904KSBL.W
Pic. 3: Coolbox Coolmatic CF 18 content 18 l., W465 x H415 x D300mm 12/24V Art. Nr. 25309020014

Pic. 7

Pic. 3

Pic. 8

Pic. 9

Pic. 4

Pic. 5
Pic. 11: Compressor coolbox 44 L. B617xH240xT615 mm, Danfoss compressor 12/24V Art. Nr. 25309020027

Pic. 6

Pic. 10

Pic. 11

Listen whos coming..
Original TGV Double horn black - with double magnet valve for automatic changing tones 24 Volt
3 tone air horn with 16 melodies (adjustable) 24Volt - (355x280x120mm)
Attention not permitted by the German Road Traffic Licensing Agency!

Licensing Agency!

Attention not permitted by the German Road Traffic

Art.Nr. 284097111119

Chrome Art.Nr. 284097111120 Red Art. Nr. 284097111120R
Hadley Horns 66 & 73 cm (Chrome plated) 66 cm Art. Nr. cm Art. Nr. 284097111024
Magnet valve 6mm for Hadley for single- or double horn Art. Nr. 284097111026

Horn cover cap

Horn protector cap
Stainless steel for JU 47-97
Jumbo stainless steel air horns (2-point fastening, Membrane removable, 5 year garuntee on corrosion resistance. 47 cm long Art. Nr. cm long Art. Nr. cm long Art. Nr. cm long Art. Nr. cm long Art. Nr. 284097114505 Without Horn protector cap! Art. Nr. 284097115014
Hadley single horn chromium horn, with connection angle, round funnel Typ DLH 95 - 95 cm Art. Nr. 284097111046 Typ DLH 86 - 86 cm Art. Nr. 284097111047 Typ 855 - 55 cm Art. Nr. 284097111050 Typ 856 - 48 cm Art. Nr. 284097111051
Horn cover cap must be specially ordered. Art.Nr. 284097111049

Art. Nr. 284097115014

Additional fastening for air horns to mount to HiBar roof lamp bar, 63mm pipe (1 Set for 1 air horn) necessary. Stainless steel highly polished Art.Nr. 282K09AHS100 Aluminium anodised Art.Nr. 282K09AHA100
Magnet valve-connector set 24V for 2 horns
(synchronised), 8 mm (incl. 5 m air line).
Art. Nr. 284097114520 Course valve-connector set for 2 horns
Stainless steel extra headlamp fitting with hinge, for mounting to 60mm pipe Art. Nr. 282097157499 Stainless steel extra headlamp fitting

Art. Nr. 284097114516

for mounting to 60mm pipe, e.g. for 60mm bullbar or roof bar.
Sidepipes for Daf XF models Pipe length approx. 2100 mm, 128mm pipe without thermic protection 1 outlet Art. Nr. 285047141670.outlets Art. Nr. 285047141670.outlets Art. Nr. 285047141670.3
Side panelling must eventually be shortened!

DAF XF 105

(Without pic.) DAF 95XF Side-Pipe with 129 mm (5"") Pipe length approx. 2000 mm, without thermic protection, Suitable also for cabs with side panelling 1 outlet Art. Nr. 28504A100.outlets Art. Nr. 28504A100.outlets Art. Nr. 28504A100.3 (Without pic.): Changeable cap for DAF 95XF Side-Pipe (5") made of stainless steel The changeable cap is inserted in original manifold. The exhaust manifold and muffler is completely dismounted and replaced by our complete System. Art. Nr. 28504A201.1
Mounting is not permitted by the German Road Traffic Licensing Agency!

Sidepipes

Art. Nr. 282007157499-N
Lighting with light bars from
Aluminium /Art.Nr.282K04HBA400-LED
Roof lamp bar HiBar for DAF XF105 -SUPER SPACE CABWith 4 headlight holders, pre-wired for 4 long range headlights and 2 warning lights, 63mm pipe, with 5 white LED lights.
Stainless steel highly polished Aluminium anodised without LED-lights: Stainless steel highly polished Aluminium anodised
Art. Nr. 282K04HBS400-LED Art. Nr. 282K04HBA400-LED Art. Nr. 282K04HBS400 Art. Nr. 282K04HBA400
Edelstahl/Art. Nr.282K04HBS402
Roof lamp bar HiBar for DAF XF105 -SPACE CABStainless steel highly polished Aluminium anodised without LED-lights: Stainless steel highly polished Aluminium anodised Art. Nr. 282K04HBS402-LED Art. Nr. 282K04HBA402-LED

Art. Nr. 282K04HBS402 Art. Nr. 282K04HBA402
Roof lamp bar HiBar, between the lights, for DAF XF105 -SUPER SPACE CABStainless steel highly polished Aluminium anodised without LED-lights: Stainless steel highly polished Aluminium anodised
With 4 headlight holders, pre-wired for 4 long range headlights, 63mm pipe, with 5 white LED lights.
Art. Nr. 282K04HBS403-LED Art. Nr. 282K04HBA403-LED Art. Nr. 282K04HBS403 Art. Nr. 282K04HBA403
Edelstahl/Art. Nr.282K04HBS403
Art. Nr. 282K04HBS303-LED
Stainless steel highly polished Aluminium anodised without LED-lights: Stainless steel highly polished Aluminium anodised Stainless steel highly polished Aluminium anodised without LED lights: Stainless steel highly polished Aluminium anodised
Roof lamp bar HiBar for DAF 95XF/XF95 - SUPER SPACE CAB (also suitable for the factory installed air horn), mount on the roof, with 5 white LED lights, with 4 headlight holders, pre-wired for 4 long range headlights and 2 warning lights, 63mm pipe.
Art. Nr. 282K04HBS303-LED Art. Nr. 282K04HBA303-LED
Art. Nr. 282K04HBS303 Art. Nr. 282K04HBA303
Roof lamp bar HiBar for DAF 95XF/XF95 -SPACE CAB -wide format
(Not suitable for factory installed air horns), mount on the roof, with 5 white LED lights, with 4 headlight holders, pre-wired for 4 long range headlights and 2 warning lights, 63mm pipe.
Art. Nr. 282K04HBS302-LED
Art. Nr. 282K04HBS302-LED Art. Nr. 282K04HBA302-LED
Art. Nr. 282K04HBS302 Art. Nr. 282K04HBA302
Roof lamp bar HiBar for DAF 95XF/XF95 -SPACE CAB
Narrow version, mount above the sun screen, with 3 white LED lights, with 4 headlight holders, pre-wired for 4 long range headlights, 63mm pipe.

Art. Nr.282K04HBA301-LED

Stainless steel highly polished Aluminium anodised without LED lights: Stainless steel highly polished Aluminium anodised
Art. Nr. 282K04HBS301-LED Art. Nr. 282K04HBA301-LED Art. Nr. 282K04HBS301 Art. Nr. 282K04HBA301

Art. Nr. 282K04HBA301

LED lighting is not allowed by the German Road traffic licensing regulations
to mount to the sun screen, with 4 headlight holders, pre-wired for 4 long range headlights and 2 warning lights, 63mm pipe, with 5 white LED lights.

Art. Nr. 282K04HBS300

Roof lamp bar HiBar for DAF 95XF/XF95 -SPACE CAB narrow version (Also
suitable for factory installed air horns), mount on the roof, with 5 white LED lights, with 4 headlight holders, pre-wired for 4 long range headlights and 2 warning lights, 63mm pipe.
Art. Nr. 282K04HBS300-LED Art. Nr. 282K04HBA300-LED Art. Nr. 282K04HBS300 Art. Nr. 282K04HBA300

Art. Nr. 282K04HBA204

Roof lamp bar HiBar for DAF CF 65, 75, 85 from model 2008 -visor mounted, with 3 white (front-facing) LEDs, pre-wired for 4 headlamps, with holder for 4 headlamps, 63mm pipe.

VisorBar

Art. Nr. 282K04HBS100-LED Art. Nr. 282K04HBA100-LED
Art. Nr. 282K04HBS100 Art. Nr. 282K04HBA100

Art.Nr. 282K04BEBA400

Roof lamp bar BeaconBar for DAF 95XF/XF95 Super Space Cab
with 2 mounting bracket and 3 LEDs, 63mm pipe.

BeaconBar

Art. Nr. 282K04BEBS400-LED Art. Nr. 282K04BEBA400-LED Art. Nr. 282K04BEBS400 Art. Nr. 282K04BEBA400

without LED-Lights

Art. Nr. 282K04BBS400-LED
Roof lamp bar BakBar for DAF XF 105, XF 95 and 95 XF Space Cab & Super Space Cab with
or without air deflector kit, fasten to original mounting points, without drilling, with 5 red LEDs, with 2 holder for warning lights and/or worklamps, pre wired, 63mm pipe. Stainless steel highly polished Art. Nr. 282K04BBS400-LED
Aluminium anodised without LED-Lights Aluminium anodised
Stainless steel highly polished
Art. Nr. 282K04BBA400-LED Art. Nr. 282K04BBS400 Art. Nr. 282K04BBA400
Roof lamp bar BakBar for DAF CF 65, 75, 85 Euro 4/5 from model 2001 Space Cab
fasten at the roof spoiler, with 5 red LEDs, with 2 holder for worklamps, pre-wired, 63mm pipe. Stainless steel highly polished Art. Nr. 282K04BBS201-LED
Aluminium anodised without LED-Lights
Art. Nr. 282K04BBA201-LED Art. Nr. 282K04BBS201 Art. Nr. 282K04BBA201

Aluminium anodised

Art. Nr. 282K04BBS201-LED
Roof lamp bar BakBar for DAF CF 65, 75, 85 from model 2001 Space Cab with factory airkit fitted, fasten at the roof spoiler, with 5 red LEDs, with 2 holder for Art. Nr. 282K04BBS200-LED Art. Nr. 282K04BBA200-LED

Art.Nr. 282K04BBA200-LED

worklamps, pre-wired for 2 worklamps, 63mm pipe.
Art. Nr. 282K04BBS200 Art. Nr. 282K04BBA200
For DAF 95XG, XF95 & XF105
LED lighting is not permitted by the German Road Traffic Licensing Agency !
Front lamp bar EuroBar 63mm pipe, with 4 headlight holders, with ascent, pre-wired for 4 long range headlights ( 220mm). Mounting of Hella Luminator is onlypossible with an adapterplate!
Stainless steel highly polished Art. Nr. 282K04EBS400 Aluminium anodised Art. Nr. 282K04EBA400
For DAF 65, 75, 85CF from model 2001
Stainless steel highly polished Art. Nr. 282K04EBS201 Aluminium anodised Art. Nr. 282K04EBA201

For DAF LF45 model 2001-2007 not for Euro 4/5
Stainless steel highly polished Art. Nr. 282K04EBS100 Aluminium anodised Art. Nr. 282K04EBA100
(Without pic.): For DAF 65, 75, 85CF bis Bj. 2001
Stainless steel highly polished Art. Nr. 282K04EBS200

Art.Nr. 282K04EBA400

Art.Nr. 282K04EBA201
Adapterplate for Luminator headlights to mount on Front lamp bar Type EuroBar Stainless steel highly polished Art. Nr. 282K09LAS100

Art. Nr. 282K04EBA200

Art.Nr. 282K04EBS100
white (front-facing) LEDs, 63mm pipe, with holder for 4 headlamps (e.g. Hella Rallye 3000), pre wired, with moulded rubber step.
Stainless steel highly polished Aluminium anodised without LED Stainless steel highly polished Aluminium anodised
Art. Nr.: 282K04MBA400-4XL-LED
Art. Nr. 282K04MBS400-4XL-LED Art. Nr. 282K04MBA400-4XL-LED Art. Nr. 282K04MBS400-4XL Art. Nr. 282K04MBA400-4XL

Art. Nr. 282K04MBS400-4

Front lamp bracket MultiBar XL for DAF CF 85 from model 2001 Stainless steel highly polished Art. Nr. 282K04MBS201-4XL-LED Aluminium anodised Art. Nr. 282K04MBA201-4XL-LED without LED Stainless steel highly polished Art. Nr. 282K04MBS201-4XL Aluminium anodised Art. Nr. 282K04MBA201-4XL
Front lamp bracket MultiBar for DAF 95XF, XF95 & XF105
63mm pipe, with 4 headlight holders, pre-wired for 4 long range headlights round (e.g. Art. 25609220002 or 25609220003) or 4 square (Jumbo 220 or 320).
Art. Nr. 282K04MBS400-4 Art. Nr. 282K04MBA400-4
Front lamp bracket MultiBar for DAF 65, 75, 85CF from model 2001 & CF from model 2008 Stainless steel highly polished Art. Nr. 282K04MBS201-4 Aluminium anodised Art. Nr. 282K04MBA201-4
Front lamp bracket MultiBar for DAF 65, 75, 85 up to model 2001 Stainless steel highly polished Art. Nr. 282K04MBS200-4 Aluminium anodised Art. Nr. 282K04MBA200-4
Aluminium Art. Nr. 282K04MBA300-4
Stainless steel highly polished Aluminium anodised Art. Nr. 289K04CBS305 Art. Nr. 289K04CBA305
Front lamp bracket MultiBar for DAF LF 45 - 7,5t GVW model 2001-2007, not for Euro 4/5. Stainless steel highly polished Art. Nr. 282K04MBS100-4 Aluminium anodised Art. Nr. 282K04MBA100-4
Under carriage protection ChassisBar for DAF XF105 with midlift with cutout in rear chassis, tractor unit, incl. 2 red LEDs and 1 brake light stripe, with fixing bolts & fit ro existing bolt-holes in crossmember.
(without pic.) Under carriage protection ChassisBar for DAF XF95 model 2002-2006 4x2 with disc

red/white orange/orange

!Lightning is not permitted by the German Road Traffic Licensing Agency !

Art. Nr. 25609131093-S1

!Lightning is not permitted by the German Road Traffic Licensing Agency!
2 piece: 7-poles and 2 piece park position 1 piece 15-poles and park position
Art. Nr. 288047400001 Art. Nr. 288047400002
So thats how your DAF is well in the race. Wheel applications of the finest
Pic. 1: Front wheeliner with wheelcover 22,5 - assembly with original bolts. Art. Nr. 28309845703 Pic. 2: Jumbo stainless steel wheel covering deep Art. Nr. 283097165129 drive wheel Pic. 3: Jumbo stainless steel wheel covering 11,75 x 22,5 rim - ET 135, with A/F 32, fot DAF.

Art. Nr. 283097165167

Pic. 4: Stainless steel axle cover
vented (aluminium wheel) with sleeve nuts, without Marlen-Logo.

Pic. 12

240mm high Art. Nr. 28309HS16502017 170mm medium high/steel wheel Art. Nr. 28309HS16502021 Further axle cover on request available.
Pic. 5: Stainless steel wheel screen in front, supersingle -also suitable for disk-braked semitrailers and supports. 22,5 x 11,75 Art. Nr. 28309845702 Pic. 6: Stainless steel wheel linning cover, back side universal
Pic. 7: Jumbo stainless steel wheel bolt- cover ring open steel/alu front wheel Art. Nr. 2830917165016-N Pic. 8: Stainless steel wheel cover rear Lock-Ring System
Also suitable for mounting to a semi trailer 17,5 Art. Nr. 28309845796 19,5 Art. Nr. 28309845794 22,5 Art. Nr. 28309845792
(closed) for 1 wheel, without middle pan. Measurement for rims dept 300mm. 22,5"x 9,00 inch Art. Nr. 283097165127-M 22,5" x 8,25 inch Art. Nr. 283097165127-N
Art. Nr. 28309845795 Art. Nr. 28309845793 Art. Nr. 28309845791 Art. Nr. 28309845798

Pic. 13

Pic. 9: Stainless steel wheel cover front Lock-Ring System Outer curved
Pic. 10: Stainless steel wheel cover rear 22.5 lock ring de luxe

Art. Nr. 283097165012-N

Pic. 13: Stainless steel wheel rim ring for drive wheel, wheelliner
Pic. 9 19,5 without centre pot, Lockring-System (Would be wedged) 22,5" Art. Nr. 28309845822

Art. Nr. 283097165331

Pic. 11: Stainless steel wheel cover front, lock ring de luxe (curved outwards) 22.5" Art. Nr. 28309845797 Pic. 12: Stainless steel wheel cover rear with 10 nuts Art. Nr. 28309845800
Lockring - System Pic. 7 & 12 are not included in delivery Art. Nr. 28309845821
Pic. 15: Stainless steel wheel nut caps
for sleeve nut for standard nuts pack of 20 for standard nuts pack of 10 Pic. 10 Art. Nr. 283097165331 Art. Nr. 283097165012 Art. Nr. 283097165012-N

Pic. 16

Art.Nr. 283097165332-32
Pic. 14: Stainless steel wheel rim ring for wide wheel 22,5"
Pic. 16: Wheel nut caps-pincer Art. Nr. 28309HS67520640 Pic. 17: Stainless steel wheel nut caps also available in the width A/F 27, A/F 30, A/F 32, A/F 33. I. e.: Art. Nr. 283097165332-27 oder 283097165332-33

(curved outwards) 22,5"
The Marlen-Logo for the wheel covers must be specially ordered!

17,5 19,5 22,5

Art. Nr. 28309HS67520640

Pic. 14

Pic. 15 Pic. 15 Pic. 17 Marlen Logo, approximately, for wheel covers in black, Logo chrome, self adhesive 135mm Art. Nr. 2110901 80mm Art. Nr. 2110902
Applications made of stainless steel
Applications made of polished stainless steel
Is delivered with 3M tape stuck on.
Applications for DAF XF95
XF105 Main headlights from const. year 2002 left & right (2 piece) for extra lamps in the bumper set of 2 pieces for door handle for seam on the door, 4-piece (Pic. 1) Front-Applications for: varnished upper grille, 10 pieces not varnished upper grille, 10 pieces Bumper grille applications for: varnished grill, 19 pieces not varnished upper grille, 19 pieces
Art. Nr. 288047157572N Art. Nr. 288047157586 Art. Nr. 288047157575 Art. Nr. 288047157578.1 Art. Nr. 288047157583 Art. Nr. 288047157583P
XF95 Main headlights from const. year 2002 left & right (2 piece) Applications above grill, varnished Applications above grill, unvarnished Below bumper grill, varnished Below bumper grill, unvarnished for door handle for seam on the door, 4-piece (Pic. 1) 95XF Radiator grill below (23 piece) Below bumper grill, unvarnished
Art. Nr. 288047157584 Art. Nr. 288047157584P
Registrationplateholder with 3 LED lights and fitting material, without wiring 1 part Art. Nr. 288047157585
Bumper application (3 piece)

With fog lights

Bumper application (3 piece) Without fog lights Sun screen application
Art. Nr. 288047157574 Art. Nr. 288047157574P
Art. Nr. 288047157572N Art. Nr. 288047157573 Art. Nr. 288047157573P Art. Nr. 288047157574 Art. Nr. 288047157574P Art. Nr. 288047157575 Art. Nr. 288047157578.1
Applications for DAF XF105

Art. Nr. 288047157586

Art. Nr. 288047157570
Art. Nr. 288047157570N Art. Nr. 288047157577 Art. Nr. 288047157579

Pic. 3: Pic. 4: Pic. 5:

below the main headlight
Stone protector grill for DAF XF 95 Screen with holes for protection of the lower area of the windscreen. Lattice is wave form. Mount (without drilling- handle must be shortened!) on 4 fastening points. Art. Nr. 288047300001

Pic. 1 Pic. 3

Pic. 2 Pic. 4
DAF XF 105 with lamp bracket and stone guard grid in Aluminium
DAF XF stainless steel application for the upper window of a Super Space Cab, 1-piece Art. Nr. 288047157582
95 XF Stainless steel applications for main headlights from const. year 2002 Made from highly polished stainless steel is delivered with 3M tape stuck on. Pic. 2: for main headlight, 2-piece Art. Nr. 288047157572

Art. Nr. 288047157578.1

Everything is safe. With stainless steel holders from MARLEN!
Pic. 1: Stainlees steel -fire extenguisher for 2 fire extinguisher for DAF XF 105 + XF95
glass bead blasted, assembly only with ladderholder. Fits only for not folding sideflap on the driver side.
Art. Nr. 27904FH001 Pic. 2: Stainless steel ladder holder for DAF XF 105, XF95 und 95XF Mounting on the cabs back face, driver side Art. Nr. 27904LH009-L Stainless steel modul for 2 fire extinguisher boxes Art. Nr. 27904LH009-FB
Stainless steel modul incl. 2 stainless steel-fire extinguisher holders Art. Nr. 27904LH009-FE Stainless steel modul brush- & shovel holder Art. Nr. 27904LH009-SB Pic. 3: Fire extinguisher holder box up to - 6 kg ABC fire extinguisher solid paintable polypropylen,
Temperature durability from -40 C - + 80 C. - the fire extinguisher: max 195mm, min. 140mm.

In red with window

Art. Nr. 203-010
Pic. 4: Fire extinguisher 6 kg-ABC fire extinguisher
Without wall holder, permitted PN EN 3-6 for the burn class A, B, C , capacity 27A, 183B, u. C - test and refillable, spray duration approx. 12sec, H 540mm, 160mm, CE-conform, 9,7 kg, extinguishing agent Ogniotex 107, applications temperature field -30C - 60C, Propellant nitrogen, 15bar

unchecked

Art. Nr. 203-005
Pic. 5: Gloria HGV - 2 kg ABC fire extinguisher P2G with HGV holder permitted DIN EN 3 for the burn class A,
B, C -capacity 13A, 89B, u. C, test and refillable, spray distance approx 4m., Spray duration approx. 10 sec., Measurement with holder: H316 x W115 x D160mm. GS-symbol, CE-conform unchecked Art. Nr. 203-001
suitable for SZM, DAF-95 XF and DAF95 FT
Pic. 6: Supply line carrier for 95 XF, XF 105

Art. Nr. 27704TH01

Pic. 7: Mud guard flat holder for DAF 95 XF, XF 95, XF 105 suitable for 2 mud guards. Art. Nr. 27804KH01 Mount to the rear cab wall. Pic. 8: Side window wind visor for DAF 95 & 95XF, XF95, XF 105 in Set Acrylic glass, long, screwable Art. Nr. 27104204004
Side window wind visor for DAF CF in Set Acrylic glass with tool holder Art. Nr. 27104204004.1 DAF LF Side window wind visor made of Acrylic glass incl. assembly kit Art. Nr. 27104204004.2
(Without pic.) Clim-Air window wind visor for DAF XF 105 Acrylic glass. In Set Art. Nr. 27104204004.CA Pic. 9: Splash brush universal
Rubber cover for 6kg fire extinguisher Art. Nr. 203-007
2 piece ANTI- splash side brush for the mounting to the mudguard. Assembly by means of tie-clips (Included in delivery), 6 piece per meter. Brush height: approx. 100 mm. Art. Nr. 2760901 Length approx. 2000mm

Pic. 10: DAF XF - wheel arch splash guard
For all wide wheels / Supersingle
Art. Nr. 2760401 Pic. 11: Cable support made of high-grade steel at the driver house rear wall - 4 hole attachment suitable for DAF XF Art. Nr. 203-04001K
Lock safe inside for DAF XF 105
Set for door driver- & passenger side.
Lock safe inside for DAF XF 95

Art. Nr. 203-04SS004DAF

Art. Nr. 203-04SS003DAF
Finally a few extras - also for your safety storage boxen

Art. Nr. 287097157112

Stainless steel universal rear bumper Highly polished for 6 three chamber lights, rear closed, inner height 180 mm, W2500 x H260 x D85 mm Art. Nr. 287097157713.N
Lights and registration plates not included in delivery!
Stainless steel universal rear bumper with rubber corners,
without lights (incl. yellow reflectors. B2400 x H245 x T75mm.

clo sed

Set of holder Art. Nr. 2731207166S-H
Refrigerator box screen printing wood with aluminium frameworks and drawer, lockable, without owners. W1200 x H710 x D660mm Art. Nr. 2731207166S
B 1100 x H 600 x T 630mm Art. Nr. 2731006063K.7016 Set of holder: Art. Nr. 273094002.7016 B 1150 x H 600 x T 650mm Art. Nr. 2731156065K.7016 Set of holder: Art. Nr. 273094002.7016
Storage box steel galvanizes plastic-coated in RAL 7016 dark grey, splash prooft and lockable. Strength: 1,5mm, galvanized steel sheet, without holders. B 950 x H 600 x T 630mm Art. Nr. 273956063K.7016 Set of holder : Art. Nr. 273094007.7016

Art. Nr. 273956063K.7016

I. E. Storage box - Steel galvanizes -without retaining set B 500 x H 600 x T 500 mm, splash-proof, lockable, soil and door with funier strengthen. Above with one and at the bottom left hand corner with 2 drawers, on the right of a subject for 30 danger property label. Art. Nr. 273DBF565
!Retaining set order please specially!
Retaining set for storage box, galvanized 2 pieces Art. Nr. 273DBH577 open

closed

Request our accessory folder!
Marlen Truck Styling GmbH Tornescher Weg 105 D-25436 Uetersen Fon: +? Fax: +33 www.marlen-truck.de ? email: info@marlen-truck.de