About the icons

This manual contains instructions on using this camera that will help you to use this camera safely and correctly. This will help prevent danger and injury to others.

DANGER

DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING

WARNING indicates a potentially hazardous situation, which, if not avoided, could result in death or serious injury.

CAUTION

CAUTION indicates a potentially hazardous situation, which, if not avoided, may result in a minor or moderate injury.

Danger

Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service Center. Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion. Should any form of liquid or a foreign object enter the camera, do not use it. Switch off the camera, and then disconnect the power source (batteries or AC Power Adapter). You must contact your dealer or Samsung Camera Service Center. Do not continue to use the camera as this may cause a fire or electric shock. Do not insert or drop metallic or inflammable foreign objects into the camera through access points e.g. the memory card slot and battery chamber. This may cause a fire or electric shock. Do not operate this camera with wet hands. This could pose a risk of electric shock.

Warning

Do not use the flash in close proximity to people or animals. Positioning the flash too close to your subjects eyes, may cause eyesight damage. When taking photographs, never point the lens of the camera directly into very strong light. This may result in permanent damage to your eyesight. For safety reasons keep this product and accessories out of reach of children or animals to prevent accidents e.g.: Swallowing batteries or small camera accessories. If an accident should occur, please consult a doctor immediately. There is the possibility of injury from the cameras moving parts. Batteries and camera may become hot during prolonged use and it may result in camera malfunction. Should this be the case, allow the camera to sit idle for a few minutes to allow it time to cool. Do not recharge non rechargeable batteries. This may cause an explosion. Do not leave this camera in places subject to extremely high temperatures, such as a sealed vehicle, direct sunlight or other places of extreme variances in temperature. Exposure to extreme temperatures may adversely affect the camera s internal components and could cause a fire. When in use, do not cover the camera or AC Power Adapter. This may cause heat to build up and distort the camera body or cause a fire. Always use the camera and its accessories in a well-ventilated area.

INFORMATION

Important information about battery usage It is easy to buy alkaline batteries. However, the duration for using batteries varies in accordance with the battery manufacturer or the photographic conditions. When the camera is not used, turn off the camera power. Do not recharge the non rechargeable batteries. It may cause an explosion. Please remove the batteries if the camera will not be used for long periods. Batteries can lose power over time and are prone to leaking if kept inside the camera. We recommend high capacity ALKALINE batteries as manganese batteries cannot deliver sufficient power. Low temperatures (below 0 ) can affect the performance of the batteries and you may experience reduced battery life. Batteries will usually recover at normal temperatures. Do not use old and new batteries at the same time. During extended use of the camera, the camera body may become warm. This is perfectly normal.
Using the AC power adapter (3.3V 2.0A) If you have access to a mains supply, using an AC Adapter (3.3V 2.0A) allows the camera to be used for long periods of time. Plug the adapter into the connection point (DC IN 3.3V) on the camera. Remove the batteries from the camera when using an AC adapter.
Always turn off the power before taking the AC adapter out of the mains supply. As with all mains powered devices, safety is important. Ensure that neither the camera nor adapter comes into contact with water or metallic materials. Please ensure that you use an AC adapter (3.3V 2.0A) with the correct specification for the camera. Failure to do so may affect your warranty.
Using the batteries : If the camera does not turn on after you have inserted batteries, please check whether the batteries are inserted with the correct polarity(+ and-). 1. Open the battery chamber cover by pushing in the direction of the arrow.
2. Insert the batteries taking note of the polarity (+ / -).
[ Inserting the AA type battery ]
[ Inserting the CR-V3 type battery ]
3. To close the battery chamber cover, push it until it clicks.
There are 3 indicators for battery condition that are displayed on the LCD monitor. Battery indicator Battery status There is no battery capacity. The batteries are fully Prepare new batteries. Replace with new batteries. charged.

Instructions on how to use the memory card
Maintenance of the memory card Be sure to format the memory card (see p. 67) if you are using a newly purchased memory for the first time, if it contains data that the camera cannot recognize, or if it contains images captured with a different camera. Turn off the camera power whenever the memory card is being inserted or removed. Repeated use of the memory card will eventually reduce the memory cards performance. Should this be the case, you will need to purchase a new memory card. Wear and tear on the memory card is not covered by the Samsung warranty. The memory card is an electronic precision device. Do not bend, drop or subject the memory card to any heavy impact. Do not store the memory card in an environment with strong electronic or magnetic fields, e.g. near loud speakers or TV receivers. Please do not use or store in an environment where there are extremes in temperature. Do not allow the memory card to become dirty or to come into contact with any liquid. Should this happen, clean the memory card with a soft cloth. Please keep the memory card in its case when not in use. During and after periods of extended use, you may notice that the memory card is warm. This is perfectly normal. Do not use a memory card that is used in another digital camera or memory card reader. Do not use a memory card formatted by another digital camera or memory card reader.
Preserving the memory card data If the memory card is subjected to any of the following, the recorded data may become corrupted : - When the memory card is used incorrectly. - If the power is switched off or the memory card is removed while recording, deleting (formatting) or reading. Samsung cannot be held responsible for lost data. It is advisable to copy important data onto other media as back-up e.g. floppy disks, hard disks, CD etc. If there is insufficient memory available : If you press the shutter button for the shot, a [CARD FULL !] message will appear and the camera will not operate. To optimize the amount of memory in the camera, replace the memory card or delete unnecessary images stored on the memory.
If you open the battery chamber cover when the camera power is turned on, the power will turn off automatically. Don't remove the memory card when the Auto focus lamp(Green) is blinking as this may cause damage to data in the memory card.
The camera can use SD Memory Cards, MMC (Multi Media Card), and Memory Stick Duo. Please consult the enclosed manual for using the MMC and Memory Stick Duo.

Slow synchro

Flash off
Available flash mode, by recording mode

X O X X O

O O O O O

X X X X X

X X X O O

X O X X X

X X X X O

X X O X X

O X X X X

Self-timer (

) / Right button
When the menu is displayed on the LCD monitor, pressing the Right button makes the cursor shift to the right tab. When the menu is not displayed on the LCD monitor, the RIGHT button operates as the Selftimer ( ) button. This function is used when the photographer would also like to be in the image. Selecting the self-timer 1. Rotate the MODE DIAL to select a RECORDING mode with the exception of VOICE RECORDING mode. 2. Press the SELF-TIMER button until the desired mode indicator displays on the LCD monitor. A 2 second self-timer or 10 second self-timer icon ( ) appears on the LCD monitor. 2SEC self-timer ( ): Pressing the shutter button will allow an interval of 2 seconds before the image is taken. 10SEC self-timer ( ): Pressing the shutter button will allow an interval of 10 seconds before the image is taken. 3. When you press the SHUTTER button, the picture will be taken after the specified time has elapsed.
[ Selecting the 10 SEC self-timer ]
When taking a picture using the self-timer, the self-timer lamp works as follows: 2 second self-timer setting : The self-timer lamp blinks at 0.25 second interval for 2 seconds. 10 second self-timer setting : The self-timer lamp blinks at 1 second interval for the first 7 seconds. It blinks at 0.25 second interval for the remaining 3 seconds. If you operate the Mode dial and Self-timer button during the self-timer operation, the self-timer function is cancelled. Use a tripod to prevent the camera from shaking.

MENU/ OK button

If the menu is displayed, use the 5-Function buttons to change the data values and for your changes to be accepted. If the menu is not displayed, press the MENU/OK button to display a menu for the current camera mode on the LCD monitor. Press the button again to return to the previous state.

Pressing the MENU button

2272X1704 2048X1536 1600X1200 1024X768

[ Menu off ]

[ Menu on ]
- There is no menu for VOICE RECORDING mode. - The menu screen may not show on the LCD when another button is pressed or image data is being processed. (The green lamp next to the view finder blinks) - When the menu is showing on the LCD monitor, it is not possible to operate the shutter button i.e. capture an image. To capture an image, simply cancel the menu display by pressing the MENU button.

+/- button

You can use the +/- button to adjust the values for the RGB, white balance, exposure compensation and Long Time shutter speed.

Main menu RGB

Sub menu R (Red), G (Green), B (Blue) AUTO, DAYLIGHT, CLOUDY, FLUORESCENT H, FLUORESCENT L, TUNGSTEN, CUSTOM. -2.0~0.0~+2.0(0.5EV steps) Changed by zoom scale

COPY TO MS

SELECT:T COPY:OK
All memory slots need to be loaded for the function. If the destination is smaller than the source, the remaining files are not copied. Please delete unneeded files to free up enough memory space before copying. While copying a picture, the destination file is automatically renamed to the next sequential filename after the last saved file to avoid filename duplication.

PictBridge

You can use the USB cable to connect this camera to a printer that supports PictBridge (sold separately) and print the stored images directly. Movie clips and voice files cannot be printed. Connecting the Camera to a Printer 1. Press the POWER button to turn on the camera. 2 In a mode with the exception of Voice Recording mode, SETUP press the MENU button. RESET 3. Press the LEFT/ RIGHT button and select [SETUP] COMPUTER CARD SEL. menu tab. PRINTER USB 4. Select [USB] menu by pressing the UP/ DOWN button SET:OK BACK: and press the RIGHT button. 5. Select [PRINTER] menu by pressing the UP/ DOWN button and press the OK button. 6. Press the menu button twice and the menu will disappear. 7. Use the supplied USB cable to connect the camera to the printer as shown below. 8. Turn on the printer to connect the camera to the printer.
If [COMPUTER] is selected at step 5, the camera will not connect to the printer, and the autofocus lamp will just blink green. If this happens, disconnect the USB cable and start over from step 2.
Print pictures 1. Connect the camera to the printer to display the screen. If [USB] submenu in the Setup menu is configured as [COMPUTER], the previous screen will remain and the camera will not connect to the printer. If this happens, change the [USB] submenu to [PRINTER] (See page 72)

CONNECTING.

USB I/F : PRINTER
2. After a successful connection, the PictBridge icon( ) will show at the top left of the LCD and the file to print is displayed (still image) Press the Left/Right button to select a picture to print. Press the OK button to print the selected picture.

PRINT:OK MOVE:

Print Error Printing is available even if this message is displayed while printing. Please check the camera and the printer after printing

NOW PRINTING

If this message is displayed while printing, please press the OK button and repeat step 2.

ERROR BACK:OK

Setup menu
In this mode, you can set up basic settings. You can use the setup menu in all camera modes, except Voice Recording mode. The items indicated by are default settings.

Menu tab

Main menu FILE

Sub menu RESET

Secondary menu

Page p.65

SERIES PWR OFF OFF, 1 ~ 3 ~ 10MIN ENGLISH PCCK FRANAIS DEUTSCH LANGUAGE ESPAOL ITALIANO DANSK SVENSKA SUOMI THAI NO FORMAT YES 04 / 01 / 01 13:00 YY/MM/DD D & TIME MM/DD/YY DD/MM/YY OFF IMPRINT DATE D&TIME OFF LOW SOUND MEDIUM HIGH p.69 p.68 p.68 p.67 PORTU. DUTCH p.67 p.66
Menu tab Main menu Sub menu DARK LCD NORMAL BRIGHT NTSC VIDEO PAL Q.VIEW RESET YES SD/MMC CARD SEL. MS DUO COMPUTER USB PRINTER * Menus are subject to change without prior notice. p.72 p.72 OFF, 1, 2, 3SEC NO p.71 p.71 p.70 p.69 Secondary menu Page

File name

This function allows the user to select the file naming format. Assigning File Names 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. RESET FILE SERIES PWR OFF 3. Select the [FILE] menu by pressing the UP/ DOWN button LANGUAGE and press the RIGHT button. SET:OK BACK: 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. [RESET] : After using the reset function, the next file name will be set from 0001 even after formatting, deleting all or inserting a new memory card. [SERIES] : Under this system, the file name will directly follow the last stored file name, regardless of any actions such as file deletion or formatting. 5. Press the menu button twice and the menu will disappear.
The first stored folder name is 100SSCAM, and the first file name is S4300001. Whenever you store an image, the file number is increased by 1. The file numbers are named from S4300001 to S4309999 automatically, 9999 files will be stored in a folder. The folder number is assigned sequentially from 100 to 999 as follows : 100SSCAM 101SSCAM. 999SSCAM. The files used with the memory card conform to the DCF(Design rule for Camera File systems) format.

Auto power off

This function switches the camera off after a set amount of time in order to prevent unnecessary battery drainage. Setting Power Off 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. FILE OFF PWR OFF 3. Select the [PWR OFF] menu by pressing the UP/ LANGUAGE DOWN button and press the RIGHT button. SET:OK BACK: 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. Selecting [OFF] : The power off function will not operate. [1~10 MIN] : The power will turn off automatically if not used for the period of time specified. 5. Press the menu button twice and the menu will disappear.
Even if the batteries or AC adapter are removed and inserted again, the power off setting will be preserved. Note that the automatic power off function will not operate if the camera is in PC mode, slide show, playing back a voice recording or movie clip.

Language

There is a choice of languages that can be displayed on the LCD monitor. Even if the batteries or AC adapter are removed and inserted again, the language setting will be preserved. Setting Language 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP ENGLISH FILE menu tab. PWR OFF 3. Select the [LANGUAGE] menu by pressing the UP/ FRANAIS LANGUAGE DOWN button and press the RIGHT button. SET:OK BACK: 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. LANGUAGE sub menu : Korean, English, French, German, Spanish, Italian, T.Chinese, S.Chinese, Japanese, Russian, Portuguese, Dutch, Danish, Swedish, Finnish, Thai. 5. Press the menu button twice and the menu will disappear.

Formatting a memory card

This is used for formatting the memory card. If you run [FORMAT] on the memory card, all images, including the protected images, will be deleted. Be sure to download important images to your PC before formatting the memory card. Formatting a Memory Card 1. In any mode other than Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. PWR OFF NO LANGUAGE 3. Select the [FORMAT] menu by pressing the UP/ DOWN YES FORMAT button and press the RIGHT button. SET:OK BACK: 4. Select a desired sub menu by pressing the UP/ DOWN button and press the OK button. If [NO] is selected : The memory card will not be formatted. Press the menu button twice and the menu display will disappear. If [YES] is selected : A [PLEASE WAIT!] message appears and the memory card will be formatted. If you ran FORMAT in Play mode, a [NO IMAGE!] message will appear.
Be sure to run [FORMAT] on the following types of memory card. - A new memory card, or an unformatted memory card. - A memory card that has a file this camera can t recognize or one that has been taken from another camera. Always format the memory card using this camera. If you insert a memory card that has been formatted using other cameras, memory card readers, or PCs, you will get a [CARD ERROR!] message.
Setting up the Date/ Time/ Date type
You can change the date and time that will be displayed on the captured images and set up the date type. Setting Date/Time & Selecting Date Format 1. In any mode with the exception of Voice Recording mode, press the MENU button. 2. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. LANGUAGE 04 / 01/ 01 01:00 FORMAT 3. Select the [D&TIME] menu by pressing the UP/ DOWN YY/MM/DD D & TIME button and press the RIGHT button. SET:OK BACK: 4. Use the UP, DOWN, LEFT, and RIGHT buttons to select the desired submenu value, and then press the OK button. RIGHT button : Selects the year/month / day/hour / minute date type. LEFT button : Moves the cursor to the [D&TIME] main menu if the cursor is at the first item of the date and time setup. In all other cases, the cursor will be shifted to the left of its current position. UP and DOWN buttons : Changes the setting value. - Date type : [YY/MM/DD] /[MM/DD/YY]/[DD/MM/YY] 5. Press the menu button twice and the menu will disappear.

If the camera is exposed to an electronic interference, it will turn itself off to protect the memory card. Camera Maintenance - Use a soft brush (available from photo stores) to gently clean the lens and LCD assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid can be used. Clean the camera body with a soft cloth. Do not allow this camera to come into contact with solvent materials such as benzol, insecticide, thinners etc. This may damage the body shell of the camera and also affect its performance. Rough handling can damage the LCD monitor. Take care to avoid damage and keep the camera in its protective carry case at all times when not in use. Do not attempt to disassemble or modify the camera. Under certain conditions, static electricity can cause the flash unit to fire. This is not harmful to the camera and is not a malfunction. When images are uploaded or downloaded, the data transfer may be affected by static electricity. In this case, disconnect and re-connect the USB cable before trying the transfer again.

Warning indicator

There are several warnings that may appear on the LCD display Warning indicator Causes - Memory card error CARD ERROR ! Remedy - Turn off the camera power and turn it on again - Insert the memory card again - Format the memory card (p.67) - Insert a new memory card

CARD FULL !

- There is insufficient memory capacity to take an image
- Delete unnecessary image files to free up some memory - There are no images stored on the memory card - Take images - Insert a memory card that is holding some images - A memory card is not inserted - The camera can t recognize the memory card - Insert a memory card - Insert the memory card again - Turn off the camera power and turn it on again

NO IMAGE !

NO CARD !

FILE ERROR !

- File error - Memory card error - There is low battery capacity - The memory card is locked
- Format the memory card - Contact a camera service center - Insert fresh batteries

LOW BATTERY !

CARD LOCKED !
- MS DUO : Slide the write protect switch to the bottom of the memory card - SD : Slide the write protect switch to the top of the memory card - Use a tripod and take pictures in Flash Photography mode

LOW LIGHT !

- When taking pictures in dark places
Before contacting a service center
Please check the following Symptom Causes - There is low battery capacity - An AC Power Adapter is not connected - Batteries are inserted incorrectly with the reverse polarities - The batteries are exhausted - The Camera is turned off automatically - The Adapter plug is not connected securely - The Camera is being used in low temperatures Remedy - Insert fresh batteries - Connect an AC Power Adapter - Insert the batteries according to the polarity marks (+, -)

File Format

Storage

Image Size

Capacity (32MB)

Image Play

Type Editing

Interface

Power Source
Dimensions(W x H x D ) Weight Operating Temperature Operating Humidity Camera Driver Software Application

Special Features

* Specifications are subject to change without prior notice. * All trademarks are the property of their respective owners.

Software Notes

Please ensure that you read the instruction manual carefully before use. The attached software is a camera driver and image editing software tool for Windows. Under no circumstances should all or part of either the software or the user manual be reproduced. Copyrights for software are licensed only for use with a camera. In the unlikely event of a manufacturing fault, we will repair or exchange your camera. We cannot, however, be held responsible in any way for damage caused by inappropriate use. Using a Hand-made PC or a PC and OS that has not been guaranteed by the manufacturer is not covered by the Samsung warranty. Before reading this manual, you should have a basic knowledge of computers and O/S (Operating Systems).

System Requirements

For Windows PC with processor better than MMX Pentium 233MHz (XP : Pentium II 300MHz) Windows 98/98SE/2000/ME/XP Minimum 32MB RAM (XP : 128MB) 140MB of available hard-disk space USB port CD-ROM drive 800x600 pixels, 16-bit colour display compatible monitor (24-bit color display recommended) Mac OS 9.0 ~ 10.2 Minimum 64MB RAM 110MB of available hard-disk space USB port CD-ROM drive QuickTime 4.0 or later for Movie Clip For Macintosh Power Mac G3 or later

About the software

After inserting the CD-ROM provided with this camera into the CD-ROM drive, the following window should automatically run. Before connecting the camera to the PC, you should first install the camera driver.
Figures (Images) used for the manual are based on model Digimax 430. Camera driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader. After installing the driver and connecting this camera to the PC, you can find [Removable Disk] in [Windows Explorer] or [My computer]. A USB Storage Driver is provided only for Windows. A USB Driver for MAC is not included with the Application CD. But you can use the camera with Mac OS 9.0 ~ 10.2. Digimax Viewer : This is a program for viewing stored images. You can see the stored images in the memory directly on a PC monitor. You can also copy, move or delete the images and enlarge/downscale the image sizes with Digimax Viewer. This software is only compatible with Windows. PhotoImpression : Image editing program. You can edit or store still images that you download from the camera. This software is only compatible with Windows.

Be sure to check the system requirements (page 83) before installing the driver. You should allow 5~10 seconds for running the automatic setup program according to the capability of the computer. If the frame does not show, run the [Windows Explorer] and select [Samsung.exe] in the CD-ROM Drive root directory.
Setting up the application software
To use this camera with a PC, install the application software first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program.
Close other programs before installing the application software. Before installing the application software, disconnect the USB connection.
You can visit the Samsung web-site through the internet. http://www.samsungcamera.com : English http://www.samsungcamera.co.kr : Korean
1. Click the [Install] menu in the Autorun frame. The Digimax 430 camera driver is installed automatically.

[Click!]

2. Camera driver installation is complete. Click the [Finish] button.
3. A window for which you can select application software will be displayed. Select the application program and click the [Install] button. Refer to page.84 for more information about the application program.
If you select [Exit] at the step 3, the application program installation will be cancelled.
4. Install Digimax Viewer. Click [Next >] button.
If you select [Cancel] at step 4, a window for installing PhotoImpression will be displayed.
5. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [No] and the installation program will be canceled.
6. A destination selection window will open. Click [Next >]. To copy to the files to another folder, click [Browse (R).] and choose a folder you want.
7. A window will open, asking you to choose a folder to which program icons will be added. Click [Next >] button. If you want to add the program icons to a different folder, choose another folder, and then click [Next >] button.
8. Digimax Viewer Installation is completed. The PhotoImpression installation window will be displayed as shown alongside. Click the [OK] button.
If you click [Cancel] in Step 8, the PhotoImpression installation will be canceled and the Restart Computer window will appear.
9. A Welcome window will be displayed. Click the [Next >] button.
10. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [No] and the installation program will be canceled.

Starting PC Mode

If you connect the USB cable to a USB port on your PC and then turn on the power, the camera will automatically switch to "computer connection mode". In this mode, you can download stored images to your PC through the USB cable. The LCD monitor is always turned off in PC mode. The auto focus lamp will illuminate when the files are transferring via the USB connection. Connecting the camera to a PC 1. Turn the PC power on. 2. Turn the camera power on. 3. In any mode other than Voice Recording mode, press the MENU button. NOR 2272 4. Press the LEFT/ RIGHT button and select the [SETUP] SETUP menu tab. RESET COMPUTER CARD SEL. 5. Select the [USB] menu by pressing the UP/ DOWN PRINTER USB button and press the RIGHT button. SET:OK BACK: 6. Use the UP and DOWN buttons to select [COMPUTER], and then press the OK button. 7. Press the menu button twice and the menu will disappear. 8. Connect the PC and the camera via the USB cable. - Insert the small plug of the USB cable into the camera USB connection terminal. - Insert the large connector of the USB cable into the USB port of the PC. - The plugs must be firmly inserted. If you selected [PRINTER] in Step 6, when you connect the camera to your computer, the [CONNECTING.] message will be displayed on the LCD monitor and the connection will not be established. In this case, disconnect the USB cable, and then follow the procedure from Step 3 and onward.
Disconnecting the camera and PC : Refer to page 96 (Removing the removable disk).
The camera driver must be installed before using PC mode. To save battery power, it is recommended that you use an AC adapter (Optional) when connecting the camera to a computer.
Downloading stored images You can download the still images stored on the camera to your PC's hard disk and print them or use a photo editing software to edit them. 1. Connect the camera to your PC with the USB cable.
2. On your computer's desktop display, select [My computer] and double click [Removable Disk DCIM 100SSCAM]. The image files will then be displayed.
3. Select an image and press the right mouse button.
4. A pop-up menu will open. Click [Cut] or [Copy] menu. - [Cut] : cuts a selected file. - [Copy] : copies files.
5. Click a folder where you want to paste the file.
6. Press the right mouse button and a pop-up menu will open. Click [Paste].
7. An image file is transferred from the camera to your PC.
- By using [Digimax Viewer], you can see the stored images in the memory directly on the PC monitor and you can copy or move the image files.
Removing the USB Driver for Windows 98SE
To remove the USB driver, refer to the process shown below. 1. Trace [Start Settings] and click [Control Panel].

Using the USB Driver for MAC
1. Double click a new icon on the desktop and the folder in the memory will be displayed. 2. Select an image file and copy or move it to MAC.
If you use Mac OS 10.0 or later, you may experience an error occurring when you transfer files from the PC to the camera.

Using PhotoImpression

With PhotoImpression, you can edit or store still images that you downloaded from the camera. This software is only available in Windows version. Programs To start the program, click [Start PhotoImpression4]. The following screen will appear. ArcSoft PhotoImpression 4

[ Help Button ]

[ Command Button ] [ Tool Bar ]
You can use PhotoImpression to perform the following tasks.
Command Button Button Description Imports a picture from an album, a source folder, or the camera/scanner, or captures screen shots of what is being viewed on the current monitor. Selects Cut, Resize, Edit Image, Insert Text, Enhance Picture, Insert Effects, or Layer. Performs Insert Frame, Insert Borders, Insert Calendar, Insert Greeting Cards, Insert Template, or Connect with Other Software. Saves the edited picture, and sends an e-mail or uses it as the background image. Outputs the edited picture according to your preferences.
Tool Bar Button Description Resize Layer Button Description Rotate Layer

Flip Layer Horizontally

Rotate All Layers

Delete Layer

Close Picture
For detailed instruction on how to use PhotoImpression, please refer to the program's Help.

Digimax Viewer 2.1

This software is only compatible with Windows. 1. To open Digimax Viewer, click the [Start Programs Samsung Digimax Viewer 2.1 Digimax Viewer 2.1 ] and Digimax Viewer 2.1 will then open.
2. If the [Auto Launch] option is selected, this program will be executed automatically with recognizing the camera.
3. You can easily use the Digimax viewer 2.1 program as it offers a FILE menu and TOOL bar. And, you can use the pop up menu. Click an image and press the right mouse button.
Digimax Viewer functions are listed below. - Basic functions : Copy, Cut, Paste, Delete, Rotate, Rename, changing file type, Resize, Property. - Advanced functions : Print, Slide show, Export, Sending e-mail, On-line print, Web album etc.
Before deleting images from the camera, you should protect or download images to your computer that you wish to keep. Refer to the [Help] menu in Digimax viewer 2.1 for further information.