Do not modify or process the power cord or plug arbitrarily. Do not bend or twist the power cord too much. Make sure to disconnect the power cord with holding the plug. Separate heat appliances from the power cord as distance as possible in order to prevent the cover from being melted.
2. Failure to follow one of them may cause electrical shock.
Do not open the main body. Do not insert metals or inflammable objects inside the product. Do not touch the power plug with a wet hand. Disconnect the power cord in case of lightning. Do not cover the receivers ventilation openings with items such as newspapers, clothes etc. Do not place the receiver on top of household appliances that emit heat.

VENTILATION:

ATTACHMENTS:
CONNECTION TO THE CABLE TV SIGNAL AND TV:
Connect all components before plugging any power cords into the wall outlet. Always turn off the STB, TV and other components before you connect or disconnect any cables.
3. Do not use the product when it is out of order. If you continue to use the product with a defect, it can cause a serious damage to the product. Make sure to contact your local product distributor when the product is out of order.

SERVICING:

Do not attempt to service this product yourself. Any attempt to do so will make the warranty invalid. Refer all servicing to a qualified service agent. If the STB is installed in an area subject to intense lightning activity, protection devices for the STB mains connector and modem telephone line are essential. The individual manufacturers instruction for safeguarding other equipment, such as TV set, Hi-Fi, etc., connected to the STB must also be followed during lightning storms. Terrestrial cable MUST BE EARTHED. The grounding system must comply with SABS 061.

LIGHTNING:

GROUNDING:

CONTENT

Safety Instructions. 2 General Features. 5 Connecting Your STB. 6 Description. 8 Front Panel. 8 Rear Panel. 9 Remote Control Unit. 10 Basic Functions. 12 Operating The Receiver. 15 Main Menu.15 1. Installation. 15 1.1 Select Country. 16 1.2 Auto Scanning. 16 1.3 Manual Scanning. 17 1.4 Reset to Factory Defaults. 17 2. Channel Organising. 2.1 Delete Frequency. 2.2 Delete Channel. 2.3 Delete All Channels. 2.4 Move & Edit Channel 3. Parental Lock. 3.1 Set Channel Lock. 3.2 Change PIN Code 3.3 Set Modem Lock. 21

GENERAL FEATURES

1. USER SECTION
400 PROGRAMMABLE CHANNELS SOFTWARE DOWNLOAD VIA PC ADVANCED ELECTRONIC PROGRAM GUIDE MULTI LANGUAGE SUPPORTED FOR OSD TELETEXT (VBI) SUPPORTED WITH MULTI LANGUAGE FULL FUNCTION INFRARED REMOTE CONTROL UNIT AUTO AND MANUAL SCAN FACILITY CHANNEL ORGANIZING (PROGRAMMABLE) LOW POWER CONSUMPTION AUTO UPDATED EPG

2. TUNER SECTION

50~860 MHz WIDE BAND TUNER RF LOOP-THROUGH OUTPUT (MALE) FOR ANALOG RECEIVER

3. VIDEO SECTION

DVB-T COMPLIANT MPEG-2 VIDEO (MP@ML) SUPPORTS ASPECT RATIO 4:3 (NORMAL) AND 16:9 (WIDE SCREEN) FFT: 2K OR 8K 2SCART, RCA

4. AUDIO SECTION

MPEG 1 AUDIO LAYER I & II MONO, DUAL, STEREO AND JOINT STEREO AUDIO MODE 32, 44.1, AND 48 KHz SAMPLING FREQUENCIES VOLUME CONTROL AND MUTE FUNCTION THROUGH REMOTE CONTROL UNIT SPDIF DIGITAL AUDIO OUTPUT
4. System Setup. 22 4.1 Language Selection. 22 4.2 OSD Setting. 22 4.3 Media Settings. 23 4.4 Time & Timer Setting. 23 4.5 System Information. 24 4.6 Software Upgrade. 24 4.7 MHP App Control. 24 4.8 Modem Setup. 25 4.9 Auto Operation Setting. 25 Troubleshooting. 26 Disposal. 26 Technical Specifications. 27

CONNECTING YOUR STB

1. LOCATION OF THE RECEIVER
Your RECEIVER should be placed under proper ventilation. Dont put in completely enclosed cabinet that will restrict the flow of air, resulting in overheating. The location should be safeguarded from direct sunlight, excess moisture, rough handling or household pets. Avoid stacking other electronic components on the top of the receiver. The location should be safely accessible by the cable from your antenna system. Connecting Figure
2. CONNECTING THE RECEIVER WITH AERIALS
You can connect the receiver to the following type of aerials: Use a standard outdoor roof aerial intended for receiving channels between VHF and UHF. Because many older roof-mounted aerials may only receive a limited number of channels, it is difficult or impossible to receive digital channels transmitted on higher frequencies. If so, you may replace the roof aerial. Some outdoor aerials are directed towards an analog transmitter. The aerial must be directed towards a digital TV transmitter. It is not desirable to use indoor or window mounted aerials, as it will be difficult or impossible to receive digital channels.
3. CONNECTING THE RECEIVER TO TV
To connect the receiver with your television, you can use SCART Cable or RCA cable. In the case of connecting your TV through SCART cable, connect the SCART connector marked TV to the respective SCART port on the TV.

4. CONNECTING YOUR VCR

To connect a VCR, the receiver has been provided with SCART at the rear marked VCR. Using a SCART connector, the VCR can be connected to the receiver. Note : In some region, the digital terrestrial signal may be weak. So youd better use the antenna in which the booster was built, for watching the weak signal channels.

5. CONNECTING YOUR ANALOG RECEIVER
This Receiver compatible with analog signal, So dont need any other extra connection except Digital connection.
6. CONNECTING EXTERNAL AUDIO / HI-FI SYSTEM
To connect any external Audio Hi-Fi system, the receiver has been provided with two RCA connectors at the back of the receiver, marked with AUDIO L and R respectively to connect the left and right Audio.
7. CONNECTING DIGITAL AUDIO SYSTEM
Connect a fiber optic cable between SPDIF on the receiver and OPTICAL on the Digital Audio System.

DESCRIPTION

Front Panel

Rear Panel

This key is used to turn the receiver on and off (Standby).
1. MODEM 2. RF OUT 3. RF IN 4. TV 5. VCR 6. VIDEO, AUDIO L/R 7. SPDIF 8. RS-232
Modem is a terminal which shares a line with a phone using splitter. It is used for handling PPV and transferring subscription information. This is used to connect to your TV via RF cable. Use to connect a terrestrial antenna. This is used to connect to your TV. This is used to connect to your VCR. These RCA connectors are for connecting any external video and audio. Output for connection to a digital amplifier. This is used to connect your receiver to a computer for reading and loading data information.
2. 7 Segment Display This LED display will show the current channel number. While the receiver is in Standby mode, the display will show the current time. 3. Infrared Sensor 4. EXIT 5. MENU 6. OK 7. 8. , , This is to receive the IR commands from the Remote Control Unit. This is for exiting a menu or returning to the previous menu or exiting some banners. This is for opening up the menu or returning to the previous menu. This is for entering and confirming any data to the receiver in the menu system. This key is for selecting the item. These keys are used to change the channels. These keys are used to increase and decrease the volume level manually. Slot for smartcard.

9. Card Slot

Remote Control Unit
1. POWER Puts the STB in stand-by mode (no signal to TV). Buttons color is gray.
2. 0-9 Numeric key Enter numeric value and to select the channel directly by entering number on the Service list. 3. TEXT 4. BACK 5. MUTE 6. EXIT 7. VOL+/VOL8. CH+/CHThis key is used to select the teletext mode. This key is used in the MHP Application. This key is used to toggle between normal & muted audio. Exit a menu or return to the previous menu. These keys are used to increase or decrease the volume. These keys are used to change channels.
9. Color key (RED, GREEN, YELLOW, BLUE) Used to select special operation for the STB. 10. Arrow Key OK 11. APP 12. LIST 13. MENU 14. i 15. EPG 16. TV/RADIO 17. ALT Move the highlight bar for the MHP Application. Enter and confirm any data to the receiver in the menu system. This key is the hard key for accessing the SAMSUNG application manager. Press while viewing TV and a list of channels is displayed. This key is used to open up the menu or return to the previous menu. Button is the Now and Next Information Key. Electronic Program Guide button displays the TV/Radio Program guide. Toggle between the TV and Radio channel. This key is used to select the soundtrack/videotrack list for the current service. Reserved.

N o t e : When inserting batteries, make sure that the polarity(+/-) is correct.

BASIC FUNCTIONS

1. Display Screen
Before you can view the television program, you must perform the installation. Therefore you will see only menu images at first. After the television channels have been programmed, you will see the following picture (banner) each time you switch channels:

3. Select Soundtrack

Press the ALT key to see the soundtrack list. Press the / and OK keys to select one.

Channel Number

4. Select Videotrack
Signal Status Program Information The number of soundtrack in current channel
Press the ALT key twice to see the videotrack list. Press the / and OK keys to select one.
Press the i key in view mode.
You will also see this picture each time you change channels. When you press TV/RADIO key on the Remote Control Unit, TV and Radio program are toggled. Detailed program information
Press the i key twice while you are viewing a program.

5. Service List

Press the LIST key while you are viewing a program. Select list by pressing the TV/RADIO. The icon behind the channel name symbolizes scrambled channel, and the icon behind the channel name symbolizes parental locked channel.
First you will see the banner described above. After pressing the i key a second time you will receive detailed program information for current program can be displayed on another banner, if there is more information. When this information is more than one page, CH+/CH- can be used for page up and down. Note : This service depends on service provider.
Select the channel by pressing the / and press the CH+/CH- for moving up or down pages on the lists. Press the OK key to watch that channel.

2. Volume Control

To control the volume level :
Press the VOL+ or VOL- keys to adjust the volume level. Press the MUTE key to turn to silence mode. Press the MUTE key again or VOL+ or VOL- keys in order to cancel the mute function. GB-12
D i g i t a l T e r r e s t r i a l R e c e i v e r

OPERATING THE RECEIVER

6. Program Information
EPG-Electronic Program Guide The electronic program guide gives you a channel list for the channels. Note : 1. This service depends on service provider. 2. After receiver recognized the GMT-time from the signal which takes few seconds, it can display correct EPG information.

Main Menu

After installing your antenna system and STB with appropriate connectors.
Plug in the AC main power and switch on the receiver. Press the MENU key to bring up the main menu.

The following on screen display will appear: The sub menu topics will be displayed. For the sub-menus Installation, Channel Organization and Parental Lock, you need the PIN Code.
Press the EPG key while you are viewing a program.
This function is displayed on the screen by using only time.
: Red key is for moving back to the previous date. : This key is used to watch the program information, if there is more information than one page. Use the CH+/CH- keys to move up and down pages. : Use to display the program list by 30 minutes per block.

GREEN i

key : Green key is for moving to the next coming date.

key / key

1. Installation
This menu consists of 4 sub-menus: Select Country, Auto Scanning, Manual Scanning and Reset to Factory Defaults.
Time interval can be adjusted by press keys as followings on EPG screen: 1 Key: 1 hour and 30 minutes 2 key: 30 minutes 3 key: 15 minutes Select the channel by pressing the / keys and press the OK key to watch this channel.
Select Installation in the main menu mode to select the sub menu. Enter the PIN Code. If you have not entered your own PIN Code then the PIN Code 0000 applies, which was set at the factory.

1.1 Select Country

To tune-in new channels, the STB has been provided with the option Select Country. Select the country where broadcasting services are provided. After selecting the Select Country from the Installation Menu, the following screen will be displayed:

1.3 Manual Scanning

To tune-in new channels and weak signals, the STB has been provided with the option Manual Scanning where the channel data can be entered by the user. After selecting the Manual Scanning from the Installation Menu, the following screen will be displayed:
Select the country which you are in. You can select the value of ITALY, SPAIN, SWEDEN, UK, USER, BELGIUM, GERMAN, FINLAND, or FRANCE by using / key. After select option, press the OK key to choose the nation of broadcasting area to be served. If you dont want to save the changed, press EXIT key without OK key pressed. Note : If national code is changed, all of saved programs will be deleted.
Select the Channel Number. You can select the specified channel you want to find.
The followings are defined as a default, but optionally you can choose it. Signal Status bar shows you if it is valid.

1.2 Auto Scanning

The sub menu Auto Scanning will enable download of the channels automatically from the preprogrammed load. To download channels automatically:
Input the frequency of the channel you want to find. Select the bandwidth. You can select the value of 6, 7 or 8 MHz. Select the Guard Interval Mode. You can select the value of Auto, 1/32, 1/16, 1/8, or 1/4. Select the FFT (Fast Fourier Transform) Mode. The value of AUTO, 2K and 8K is settings automatically. After select option, press the OK key to start the scanning process.
You can select the specified frequency between Start Frequency and End Frequency. Press the OK key. Auto Scanning menu will be displayed. All the channels in the list will be automatically downloaded.
1.4 Reset to Factory Defaults
This is to restore the factory set values in case the user has encountered some problems after changing any values of channel data and others which may be in error. At the request window, if you press the OK key, the receiver will be reset to factory default settings automatically. Note : This cause your previous settings to be deleted!

2. Channel Organising

The Channel Organising menu has four functions: The Channel Organising menu is used to delete the Frequencies and Channels or move&edit channel as you want.
2.4 Move & Edit Channel
Select the TV/RADIO/Interactive list with / keys. Select the TV/RADIO/Interactive list with / or CH+/CHkeys. Select channel by pressing the RED key. Press the / keys to change the position of the channel you want, and CH+/CH- for moving up or down pages on list. Press the OK key for confirmation. If you want to return the channel to the initial position, do not press the OK key but press the BLUE key.

Enter the PIN Code.

If you have not entered your own PIN Code 0000 applies, which was set at the factory.

2.1 Delete Frequency

To edit Channel Name
Select the desired frequency list you want to delete by pressing the RED key. Press the OK key for confirmation. Note : This feature doesnt delete frequency itself but deletes the list of channels registered for frequency.
Select the TV/RADIO/Interactive list with / keys. Select a channel list to move to other location with / or CH+/CH- keys. Press the GREEN key. Font Table will be displayed. Select desired character with / , / and then press the OK key to paste character to the string.

2.2 Delete Channel

Note : CH- key : Backspace for deleting previous character.
Select the desired channel you want to delete by pressing the RED key. Press the OK key for confirmation.
Press the MENU key and then press the OK key to save the set data.

2.3 Delete All Channels

At the request window, press the OK key to delete all channels and press the EXIT key to exit.

3. Parental Lock

This Parental Lock feature sets viewing restrictions and prevents unauthorized access to your STB through the PIN (Personal Identification Number), which is a 4 digit number. (The factory preset PIN Code : 0000) On selecting this menu, you will have three options: to set lock for any desired channel and to change your PIN Code and to Set Modem Lock.

3.2 Change PIN Code

To change the PIN Code, select the second option Change PIN Code. This will take you to the following menu: In this option, you need to enter the current PIN Code at the first cursor, and at the second cursor enter the desired PIN Code. To confirm, you need to enter the new PIN Code again. Please remember the PIN Code should be a 4 digit numerical value.

Enter PIN Code.

If you have not entered your own PIN Code then the PIN Code 0000 applies, which was set at the factory.
THE FACTORY PRESET PIN CODE : 0 0. Note : If you forget the PIN Code, contact your dealer or service provider. Once you change password, please do not forget and keep well.

3.1 Set Channel Lock

Select the channel by pressing the / or / keys. Select the channel lock by pressing the RED key. Press the OK key for confirmation.

3.3 Set Modem Lock

To block watching the paid-service, e.g. PPV(Pay Per View) service, select the third option, Set Modem Lock. You can select Lock or Unlock in Modem Parental Lock Menu.
Whenever you need to view the locked channel, you will have to enter the PIN Code at the request window. After entering PIN Code to able to access a parental locked channel, it will work on all parental locked channels. It means that you can access all parental locked channels with entering PIN Code on any parental locked channel successfully. To cancel the lock :
Select Lock, this will make you block to watch paid-service. Select Unlock, this will make you free to watch paid-service.
Press the RED key again in order to cancel the lock.

4. System Setup

This option enables you to change the factory preset system settings as per your requirements.

4.3 Media Settings

You can set the various media settings you want. Place the cursor on this sub menu and press the OK key.

4.1 Language Selection

The Language Selection option allows the user to select the desired language of the OSD, Soundtrack, Teletext, and EPG.
To accommodate user from different regions speaking different languages, OSD languages are available 5 languages. (English, Deutsch, Franais, Italiano, and Espaol provided currently) To select the desired language menu, press the / keys to change language and press the OK key. The OSD, Soundtrack, Teletext, or EPG language will vary according to the selected language.

Press the / keys to move the sub items and press the / keys to select the option. Press the OK key to confirm. Press the MENU/EXIT keys to exit the menu. Select the TV system : PAL or SECAM. Select the TV Aspect Ratio according to your TV: STANDARD 4 : 3 ratio or WIDE SCREEN 16 : 9 ratio type. Select the Aspect Ratio Conversion : None, Letter Box or Pan & Scan. Select the Video Signal Type : Composite or Composite+RGB. RF Channel : Off or K21 CH ~ K69 CH Broadcasting System : B/G, I, D/K
4.4 Time & Timer Setting
Various time modes can be set, such as current local time, switch on/off time. The exact local present time can be adjusted by using the GMT.

4.2 OSD Setting

You can set the OSD transparency and the display(banner) time.
Place the cursor on this sub menu and press the OK key. Press the / keys to change the Local time in Time Zone. The local time will be changed according to your location.
Select OSD Transparency level. The OSD Transparency level from 0 to 100%. Setting is made with the numeric keys, / keys or CH+/CH- keys. Set the display duration of the information(banner) box displayed in the screen. The time ranges from 0.5 to 60.0 seconds. Setting is made with the numeric keys, / keys to be decrement/increment of 0.5sec and CH+/CH- keys 1sec.
GMT is referred to the standard time of Greenwich. This cannot be changed. Press the / keys to choose Event Repetition you want to reserve : Once, Daily, Every Sunday, Every Monday, Every Tuesday, Every Wednesday, Every Thursday, Every Friday and Every Saturday. Insert the preferable Switch on/off time by the Numerical (0~9) keys and / keys. Press the / keys to choose a switch time you want to reserve. Select program to set the event program by pressing the / and Numerical (0~9) keys.

4.5 System Information

If you have to contact your service provider or a service center they might ask for information available from this menu. Place the cursor on this sub menu and press the OK key. The following will be the on-screen display.

4.8 Modem Setup

If you want to setup Modem, please follow the instruction below.

4.6 Software Upgrade

Select Tone or Pulse in Dial Method. Select the Carrier Wait Time ranged in 1~255 seconds with the / keys or numeric keys. Select the Carrier Present Time ranged in 0.1~25.5 seconds with the / keys or numeric keys. Select the Carrier Loss Time ranged in 0.1~25.5 seconds with the / keys or numeric keys. Select Blank, 0, # or 9 in Prefix by using / keys, to specify your pre-dialing key for phone extension. Press OK to save Modem configuration if modified.
You can download and upgrade the system software of the receiver through a specific channel through a specific channel designated by the broadcaster. The Broadcaster will provide you with more information about that. If you select to download a new software version, all your previous settings, access code and favorite channels etc. will be erased! Downloading may take a While During downloading dont turn off the receiver.
Note : Exit without OK key makes Modem Setup unchanged.
4.9 Auto Operation Setting
You can set the parameters for searching new channels and upgrading new software.

4.7 MHP App Control

If you want to change the display mode of MHP application, please follow the instruction below.
Select Auto Start or Not Allowed in Auto Start Control mode with the / keys. Select On/Off in show Apllication List mode with the / keys. Press the GREEN key to edit contents in Phone Number, User Name and Password. Insert value by the Numerical (0~9) and / keys in DNS. Press OK to save MHP App Control.
Select YES or NO in Standby Mode and Operate Mode by using / keys. Insert the preferable time by the Numerical (0~9), CH+/CHand / keys. Press the / keys to choose Repetition you want to reserve: Daily, Every Sunday, Every Monday, Every Tuesday, Every Wednesday, Every Thursday, Every Friday and Every Saturday. Note : If YES in Standby Mode (with selecting NO in Operate Mode or Aborting the operation in progress in Operate Mode), the receiver automatically starts auto operation in Standby Mode after 45 minutes for new software and 1 hour for new channels from entering the standby mode.
Note : Exit without OK key makes MHP App Control unchanged.

TROUBLESHOOTINGS

In some region, the digital terrestrial signal may be weak. So youd better use the antenna in which the booster was built, for watching the weak signal channels. You can download and upgrade the system software of the receiver through a specific channel through a specific channel designated by the broadcaster. The Distributor will provide you with more information about that.

Problem No display LED on the front panel; No power supply No pictures on the screen Possible cause Power cord not plugged in correctly Solution of the problem Power cord plug in correctly

TECHNICAL SPECIFICATIONS

Power supply Type : Input voltage : Fuse rating : Demodulator DEMODULATION : MODE : CODE RATE : OFDM DEMODULATION (DVB-T) 2K/8K Viterbi Convolutional Code Rate - 1/2,2/3,3/4,5/6,7/8 SMPS AC 100-240V~, 50/60Hz 250V T1.6AH
Receiver in Standby mode; Scart not connected tightly to video output of television; incorrect channel or video output selected on television Audio cord connected incorrectly; Loudness level = 0; Muting active Incorrect operation; Batteries dead or inserted incorrectly Poor picture quality Signal strength too low Set receiver to On; Check connection and correct; Check channel and video output and correct (TV instruction manual) Check connection and correct; Increase loudness on television set; Press the MUTE key Point remote control towards the Receiver. Replace batteries or insert correctly

No sound

Freq. Range : Input signal level : Channel selection : Input impedance : Connector type : Video decoder System decoding : Profile and level : Data rate : Video formats : Picture resolution : Audio Decoder System decoding : Audio mode : Sampling frequency :
50~860 MHz -20 ~ -78 dBm PLL frequency synthesizer 75 unbalanced Din type female(RF in/RF out)
Remote Control does not operate directly
Check the signal strength in the Installation menu, correct alignment of your antenna Check connection and correct; Check position and correct, Check the signal strength in the Installation menu Scanning of in Installation menu
MPEG 2 ISO/IEC 13818 (Transport Stream) MPEG 2 MP@ML (4:2:2) 1~ 15 Mb/s 4:3 (normal) & 16:9 (widescreen) 720(H) x 576(V) x 50 fields/sec
On-Screen Error Message Searching for signal
Antenna cable not connected or not tight; incorrect position of the antenna;
On-Screen Error Message Channel data does not exist.

Receiver not yet set

MPEG 1 ISO/IEC 11172~3 layer I & II single channel, dual channel, stereo, joint stereo 32, 44.1, 48, 96 KHz
Note : The specification of the STB may be changed without notice in advance.

DISPOSAL

The device, packaging material (e.g. Styrofoam) and the batteries must never be disposed of with household refuse. Please obtain appropriate information about the regulations in your community, and dispose of all refuse in accordance with regulations at the separate locations provided.
RF modulator Modulator output : Video type : UHF output level : Output connector : Ant. O/P connector : Tuning method : Default Channel : A/V output TV SCART : VCR SCART : SPDIF : Physical Specification Size (W x H x D) : Weight(Net) : Operating Temperature : Storage Temperature : Etc Accessories : RCU, Users Manual, 2Batteries(AAA), Modem cable, Scart Cable 270 mm x 200 mm x 45 mm 1.2 kg 0 C to +45 C -10 C to +70 C VIDEO (CVBS, RGB), AUDIO R&L VIDEO (CVBS), AUDIO R&L Digital Audio Output CH 21~69 (preset to CH 21) PAL BG, I, D/K (preset to PAL BG) 705 dBV IEC male IEC female PLL frequency synthesizer Disabled
Correct Disposal of This Product (Waste Electrical & Electronic Equipment)
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal. GB-28