01003A-R128,130-XEU_Cover 2/20/06 7:47 PM Page 1

Instruction Manual

DVD-R120/R121 DVD-R128, R129 DVD-R130, R131

www.samsung.com/uk

English

AK68-01003A-00

01003A-R128,130-XEU_02~17 2/20/06 7:47 PM Page 2

Getting Started

Warning

IMPORTANT NOTE

The mains lead on this equipment is supplied with a moulded plug incorporating a fuse. The value of the fuse is indicated on the pin face of the plug. If it requires replacing, a fuse approved to BS1362 of the same rating must be used. Never use the plug with the fuse cover omitted if the cover is detachable. If a replacement fuse cover is required, it must be of the same colour as the pin face of the plug. Replacement covers are available from your dealer. If the fitted plug is not suitable for the power points in your house or the cable is not long enough to reach a power point, you should obtain a suitable safety approved extension lead or consult your dealer for assistance.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury.
However, if there is no alternative to cutting off the plug, remove the fuse and then safely dispose of the plug. Do not connect the plug to a mains jack, as there is a risk of shock hazard from the bared flexible cord. To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. The product unit accompanying this user manual is licensed under certain intellectual property rights of certain third parties. This license is limited to private noncommercial use by end-user consumers for licensed contents. No rights are granted for commercial use. The license does not cover any product unit other than this product unit and the license does not extend to any unlicensed product unit or process conforming to ISO/IEC 11172-3 or ISO/IEC 13818-3 used or sold in combination with this product unit. The license only covers the use of this product unit to encode and/or decode audio files conforming to the ISO/IEC 11172-3 or ISO/IEC 13818-3. No rights are granted under this license for product features or functions that do not conform to the ISO/IEC 11172-3 or ISO/IEC 13818-3.
This symbol indicates important instructions accompanying the product. Do not install this equipment in a confined space such as a bookcase or similar unit. WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. CAUTION : DVD RECORDER USES AN INVISIBLE LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.

CAUTION

THIS PRODUCT UTILIZES A LASER. USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS RADIATION EXPOSURE. DO NOT OPEN COVERS AND DO NOT REPAIR YOURSELF. REFER SERVICING TO QUALIFIED PERSONNEL. This product satisfies CE regulations when shielded cables and connectors are used to connect the unit to other equipment. To prevent electromagnetic interference with electric appliances, such as radios and televisions, use shielded cables and connectors for connections.

2- English

01003A-R128,130-XEU_02~17 2/20/06 7:47 PM Page 3

Precaution

Important Safety Instructions
Read these operating instructions carefully before using the DVD Recorder. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

CD-R/-RW MP3 CD-R/-RW

Only CD-R discs with MP3 files recorded with ISO9660 or JOLIET format can be played back Only MP3 files with the ".mp3", ".MP3" extension can be used. For MP3 files recorded with a VBR(Variable Bit Rates), from 32 Kbps to 320 Kbps, the sound may cut in out. Playable bitrate range is from 56Kbps to 320Kbps. This DVD Recorder can handle a maximum of 500 files and 100 folders.
Once a DVD-R recorded in Video Mode is finalised, it becomes DVD-Video. You can record onto the available space on the disc and perform editing functions such as giving titles to discs and programmes and erasing programmes before finalising. When programming is erased from a DVD-R, that space does not become available. Once an area on a DVD-R is recorded on, that area is no longer available for recording, whether the recording is erased or not. It takes about 30 seconds for the DVD Recorder to complete recording management information after recording finishes. This DVD Recorder optimizes the DVD-R for each recording. Optimizing is carried out when you start recording after inserting the disc or turning on the DVD Recorder. Recording onto the disc may become impossible if optimizing is carried out too many times. Playback may be impossible in some cases due to the condition of recording. This DVD Recorder can play back DVD-R discs recorded and finalised with a Samsung DVD video recorder. It may not be able to play some DVD-R discs depending on the disc and the condition of the recording.
DVD-RW Disc Playback and Recording

JPEG CD-R/-RW

Only JPEG files with the ".jpg", ".JPG" extension can be used. This DVD Recorder can handle a maximum of 500 files and 100 folders. Maximum size of progressive JPEG is 3M pixels. MOTION JPEG is not supported.
Recording and playback can be performed on DVDRW discs in both the Video and VR Modes. Once a DVD-RW recorded in both the Video and VR Modes is finalised, you cannot perform addtional recording. Once a DVD-RW recorded in Video Mode is finalised, it becomes DVD-Video. In both modes, playback can be performed before and after finalisation, but additional recording, deleting and editing can not be performed after finalisation.

English - 17

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 18
Connecting the DVD Recorder
You can connect your DVD Recorder to the television using the SCART cable if the appropriate input is available on the television.

Additional connections

You can connect your DVD Recorder to a satellite or digital tuner.
1. Connect the RF cable as shown. 2. Connect one end of the SCART cable to the AV1 socket on the rear of the DVD Recorder. 3. Plug the other end into the appropriate connector on the television. 4. Plug in the DVD Recorder and TV 5.Turn on the DVD Recorder and TV. 6. Press the INPUT SEL. button on your TV remote control until the Video signal from the DVD Recorder appears on the TV screen.
external device (VCR/Satellite receiver)

To RF IN

- DVD mode

To RF OUT

1. Connect the AV2 connector of DVD Recorder and VCR/Satellite receiver or digital tuner using a SCART cable. 2. Connect the AV1 connector to the SCART AV connector on TV.

RF Cable To ANT INPUT

3. Turn on the DVD Recorder, VCR/Satellite receiver or digital tuner and TV. 4. Set Input mode on AV2.

- TV mode

The RF cable connection of this DVD Recorder sends only signals of TV. You must connect SCART cable or Audio/Video cables to watch a signal from your DVD Recorder. TV mode Press the TV/DVD button on remote control, then TV appear on Front LED display (or turn off DVD Recorder).
1. Press the TV/DVD button on remote control,then TV appear on Front LED display. (or turn off DVD Recorder.) 2. You can watch programmes from a satellite or digital tuner connected to this DVD Recorder, even when the DVD Recorder is turned off.

18- English

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 19
Other type of connecting the Video output cable
There are several ways to output video signal not using scart cables. Select one of the following video connecting that best suits you below. Case 1 : Connecting to a Video (Composite) output jack Case 2 : Connecting to an S-Video output jack Case 3 : Component Video output jacks

Auto setup will be started. Check antenna and TV cable connection.
4 Auto Channel scan will be started.

Auto channel memory

The number of stations automatically stored by the DVD Recorder depends on the number of stations that it has found.

English -25

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 26

Setting the Clock

the 4 PressClock. buttons to select On for the Auto
No Disc Programme Setup Date JAN SUN Time Auto Clock On Clock Set
This menu is used to set the current time. You need to set the time to use timer recording.
With the DVD Recorder in Stop mode/No Disc mode, press the MENU button.
the 5 Presswill beOK button, then the date and time saved.
If you dont press the OK button, it will not be saved.

MOVE OK RETURN EXIT

You must have the RF cable connected to set the Auto Clock. (See page 18) The DVD Recorder automatically sets the clock according to the time signal broadcast between the channels PR1 to PR5. If you do not need the Auto clock set function, select Off.
the press button. 2 Press the OK orbuttons to select Setup, then
No Disc Programme Setup System Clock Set Language Audio Video Parental Control Install MOVE OK RETURN
the select then the OK or 3 Presspress buttonstobutton. Clock Set,
Use the buttons to input Time, Date or Year. Use number buttons to input clock data directly.
No Disc Programme Setup Date JAN SUN Time 12

Clock Set

Auto Clock 00 On

26- English

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 27
Presetting Channels with the Auto Setup function
This feature allows you to manually set the DVD Recorder tuner band to Antenna or Cable, whichever you connected to the Antenna In jack during initial setup.
Press to Auto 4 Setup,the buttonsOKselect button. then press the or
The message Your data will be lost. Press [OK] to continue, [MENU] to exit. is displayed.
No Disc Programme Setup Auto Setup Manual Setup Your data will be lost. Press [OK] to continue, [MENU] to exit.

Install

the DVD Recorder in Stop mode/No 1 With mode, press the MENU button. Disc
5 Press the OK button to continue. 6 Channel scan will be started.
If you want to exit, press the MENU button.
Press the OK button to stop the Auto Setup.

Audio : For the speaker sound. Subtitle : For the disc subtitles. Disc Menu : For the disc menu contained on the disc On-Screen Menu : For the screen of your DVD Recorder DivX Subtitle: Selecting a supported DivX subtitle language by region.
Afrikaans, Basque, Catalan, Danish, Dutch, English, Faeroese, Finnish, French, German, Icelandic, Indonesian, Italian, Malay, Norwegian, Portuguese, Spanish, Swahili and Swedish English, Albanian, Croatian, Czech, Hungarian, Polish, Romanian, Serbian(Latin), Slovak and Slovenian English and Greek English, Azeri, Belarusian, Bulgarian, Kazakh, Macedonian, Russian, Serbian, Tatar, Ukrainian and Uzbek

Western

Central

Greek Cyrillic

to desired language, then press OK or 5 Press the buttonsthe select thebutton.
No Disc Programme Setup Audio Subtitle Disc Menu On-Screen Menu : Original English : Automatic Franais : Deutsch English : Espaol English Italiano : Western Nederlands Korean

Language

DivX Subtitle
the select 3 Presspress buttonstobutton. Language, then the OK or
Language setup menu will be displayed.
Press the RETURN or button to return to the previous menu. Press the MENU button to exit the menu. The selected language will only appear if it is supported on the disc. If the subtitle language is displayed in broken fonts, change DivX Subtitle to the appropriate region. If it still does not work, the format is not supported.

DVD-Recorder

No Disc Programme Setup Audio Subtitle Disc Menu : Original : Automatic : English
On-Screen Menu : English DivX Subtitle : Western

English -29

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 30

EP Mode Time Setting

Press to EP Mode 4 Time, the buttonsOK selectbutton. then press the or
No Disc Programme Setup EP Mode Time Chapter Creator Quick Recording : 6 Hours 6 Hours 8 Hours Off : Off

System

You can select one of four recording modes by pressing the REC MODE button repeatedly. EP mode is one of four REC Mode (XP,SP,LP,EP). In EP(Extended Play) mode, you can set recording time to 6 or 8 hours by this setting.
the 5 Pressthen buttons toorselect the desired time, press the OK button.
Press the 2 press the OK orbuttons to select Setup, then button.
Press the select 3 then press buttonstobutton. System, the OK or
System menu will be displayed.
No Disc Programme Setup EP Mode Time Chapter Creator : 6 Hours : Off

Quick Recording : Off

30- English
01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 31
Automatic Chapter Creation
A DVD-Video consists of Titles and Chapters. When you record one programme, it makes one Title. If you use this function, the Title will be divided into Chapters. (V mode)
Press the select 5 then press buttonstobutton. On or Off, the OK or
Off: Select this option when you do not want (Automatic Chapter Creation). On: Select this option when you want (Automatic Chapter Creation).
the button to (See 42 to set recording 6 PresspageRECabout how start recording. mode) The message Do you want to create the chapter menu after this recording? is displayed.
1 With the DVD Recorder in Stop mode, press the MENU button.
DVD-RW(V) Title List Disc Manager Programme Setup Title List
Title List Do you want to create the chapter menu after this recording?

Yes No

DVD-RW(V) Title List System Language Audio Setup Video Parental Control Install MOVE OK RETURN
Press the buttons 7 press the OKbutton. to select Yes and
A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode.
Disc Manager Clock Set Programme
8 Press the STOP button to stop recording.
the chapters, finalise disc (see 84) and the 9 To displaypagecreatedThethen pressmenu the DISC MENU button. chapter will be displayed.
the select 3 Presspress buttonstobutton. System, then the OK or
DVD-RW(V) Title List EP Mode Time : 6 Hours : Off
Disc Manager Chapter Creator
Programme Quick Recording : Off Setup
Previous MOVE OK RETURN EXIT
buttons select 4 Press thethen press thetoOK or Chapter Creator, button.
DVD-RW(V) Title List EP Mode Time : 6 Hours : Off Off
The Automatic Chapter Creation function does not work during Timer Recording or when you turn the power off. DVD-R discs cannot be unfinalised.
Off Programme Quick Recording : On Setup

English -31

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 32

Quick Recording Setting

the 5 Press the OK orbuttons to select On, then press button.
If this function is set to on, both the DVD Recorder and the TV will power on at the same time, which enables you to immediiatedly record a desired channel.

DivX(R) Registration

Please use the Registration code to register this DVD Recorder with the DivX(R) Video On Demand format. For more information, visit www.divx.com/vod
Setting up the Audio Options
You can connect the DVD Recorder to an external amp or Home Theatre. Allow you to setup the Audio device and sound status depending on the audio system in use.

Quick 4 Press the buttons to selector button. Recording, then press the OK
No Disc Programme Setup EP Mode Time Chapter Creator : 6 Hours : Off On
No Disc Programme Setup System Clock Set Language Audio Video Parental Control Install
Quick Recording : Off Off

32- English

01003A-R128,130-XEU_18~40 2/20/06 7:48 PM Page 33
the 3 Press the OK orbuttons to select Audio, then press button.
Audio setup menu will be displayed.
No Disc Programme Setup Digital Output DTS : PCM : Off
1. Off : Doesnt output DTS signal. Select this when your AV receiver or AV amplifier does not have DTS decoder. 2. On : Outputs DTS Bitstream via digital output when you play DTS track. Select this only when your AV receiver (or AV amplifier) have DTS decoder.
Dynamic Compression : On NICAM : On
When DTS soundtrack is played, sound does not output from AV Audio Output.
Press the buttons select desired 4 button.option, then presstothe OKthe audio or
No Disc Programme Digital Output Setup DTS : PCM : Bitstream Off
Dynamic Compression This is only active when a Dolby Digital signal is detected. 1. Off : You can enjoy the movie with the standard Dynamic Range. 2. On : When Movie soundtracks are played at low volume or from smaller speakers, the system can apply appropriate compression to make low-level content more intelligible and prevent dramatic passages from getting too loud.
the 5 Pressthen buttons toorselect the desired item, press the OK button.
NICAM NICAM programmes are divided into 3 types. NICAM Stereo, NICAM Mono and Bilingual (transmission in another language). NICAM programmes are always accompanied by a standard mono sound broadcast and you can select the desired sound by setting NICAM on or off. 1. On : NICAM mode 2. Off : Only set at this position to record the standard mono sound during a NICAM broadcast if the stereo sound is distorted due to inferior reception conditions.
Press the RETURN or button to return to the previous menu. Press the MENU button to exit the menu.

Press the 3 area you want buttons to move to the to enlarge. The screen enlarged twice the 4 Press thetoOK button. normal size.will be
This function is disc-dependent, may not work on all DVDs. This function does not work when a DVD has not been recorded with a multicamera angle system.
If you press the OK button again after the screen was enlarged to twice the normal size, the screen size will be enlarged to four times the normal size.
normal size 2X 4X 2X normal size
You can also select Zoom function directly using ZOOM button on the remote control.

56- English

01003A-R128,130-XEU_49~68 2/20/06 7:50 PM Page 57

Using Bookmarks

This feature lets you bookmark sections of a DVD-VIDEO or DVD-R/-RW(V mode), so you can quickly find them.

Playing back a bookmark

(V mode)
Press the 1 playback. MARKER button during bookmarked scene. 2 Press the buttons to select a

Bookmark

- - - - - - - --
1 Press the MARKER button during playback.

- - - - - - - - - --

MOVE MOVE OK RETURN
Press the OK button when the desired scene appears.
The number 1 is displayed and the scene is memorized.
or PLAY button to 3 Press the OKthe selected scene. start playing from

Clearing a bookmark

1 - - - - - - - - --
Press the 1 playback. MARKER button during

MOVE PLAY CLEAR RETURN

2 Press the buttons to select a bookmarked scene.
3 Press the button to move to the next position. 4 Press the OK button when the desired scene appears.
The number 2 is displayed and the scene is memorized.
Press the CANCEL 3 selected bookmark. button to delete the
Repeat above to bookmark other positions. You can bookmark up to 10 scenes.
When the disc tray is opened and then closed, bookmarks will disappear.

English -57

01003A-R128,130-XEU_49~68 2/20/06 7:50 PM Page 58

Using Markers

Playing back a Marker

(VR mode)

Marker
-- -- -- -- -- -- -- -N:2
-- -- -- -- -- -- -- -- -- -N:0
The number 01 is displayed and the scene is memorized.
01 -- -- -- -- -- -- -- -- --
If you press the SKIP( ) button, it moves to the beginning of the marker. Pressing the button once again within 3 seconds returns to the beginning of the previous marker. If you press the SKIP( ) button, it moves to the next marker.

Clearing a Marker

Press the button to move to the next position. Press the OK button when the desired scene appears.
The number 02 is displayed and the scene is memorized.
2 Press the buttons to select a the bookmarked scene. Press the CANCEL button to delete

selected bookmark.

N : 10

-- -- -- -- -- -- -- --

English -59

01003A-R128,130-XEU_49~68 2/20/06 7:50 PM Page 60

Playing an MP3 Disc

MP3 Screen Elements
1 Insert an MP3 Disc into the disc tray.
CD Disc Navigation Disc Navigation DivX
Music List 01/13 No. Title ROOT SONG01 SONG02 SONG03 SONG04 SONG05 SONG06 OK RETURN EXIT

SONG01

0:00:15

006 MOVE

SONG01 4.0MB 01/26/2006
Programme Photo Music Setup
Press the buttons to select 2 Navigation, and then press the Discor OK button.
CD Disc Navigation Disc Navigation
1. Play mode icon 2. Current track (song) 3. Displays the current track(song) information. 4. Shows the operating state of a disc and a playback time corresponding to a portion that is currently played. 5. Displays the information for the folder and its tracks. 6. Button display.
Press the 3 press the OK orbuttons to select Music, then button.
SONG01 No. Title ROOT SONG01 SONG02 SONG03 SONG04 SONG05 SONG06 OK RETURN EXIT Music List 01/13
The MP3 menu appears and the tracks(songs) are played automatically.
the buttons to select the 4 Pressbutton.want to hear, then press trackOK (song) you the or

60- English

01003A-R128,130-XEU_49~68 2/20/06 7:50 PM Page 61
Buttons on the Remote Control used for MP3 playback

^ % & *

Press the REPEAT button during playback.
The Track repeat mode icon ( ) appears and the selected track is played repeatedly.

0:00:07

Press the REPEAT button once more to play the disc repeatedly.
The Disc repeat mode icon ( ) appears and the inserted disc is played repeatedly. For MP3 disc, the Folder repeat mode icon( ) appears and all tracks in the current folder are played repeatedly. Pressing the REPEAT button once more changes the mode to the Disc repeat mode.
1. : Selects a track (song). 2. : Plays the selected track (song). 3. OK button: Plays back the selected track (song) or displays the files in the selected folder. 4. RETURN button: Moves to the folder to which the current song belongs. 5. SKIP( ) button: Plays the next track. 6. SKIP( ) button: Returns to the beginning of the current track when pressed while playing. If pressed again, your DVD recorder moves to and plays the previous track. If you press the this button within three seconds, the previous track will be played. If you press the this button after three seconds, the current track will be replayed from the beginning. 7. STOP button: Stops a track(song). 8. PLAY/PAUSE button: Plays a track(song) or pauses playback. 9. ANYKEY button: Selects the sub menu on screen display (Repeat or Play Option).
To return to normal playback
Press the REPEAT button repeatedly until the repeat mode icon disappears, or press the CANCEL button.

English -61

01003A-R128,130-XEU_49~68 2/20/06 7:50 PM Page 62

DVD-RW(VR) Modify Scene Scene No. 002 Start End Title List : 5/6
buttons to 4 Press the tomodify, thenselect the scene you want press the OK button.
Start DVD-Recorder DVD-RW(VR) Scene No. 2/7 Edit Scene Playlist No. 3 Play Modify 01 00:00:00:00:00:00:04 Move Add 04 00:00:03 MOVE 05 00:00:11 OK 06 00:00:04 RETURN Delete EXIT

00:00:25

00:00:30 00:00:30

Change OK RETURN

Cancel EXIT
The image and ending point time are displayed in the End window.
Press the buttons 8 press the OKbutton. to select Change, then
DVD-Recorder DVD-RW(VR) Scene No. 2/7 Edit Scene Playlist No. 3 Play Modify 01 00:00:00:00:00:00:04 Move Add
Press the buttons to select Modify, then press the OK button.
The Modify Scene screen is displayed.
DVD-RW(VR) Scene No. 002 Start End Modify Scene

Title List : 5/6

The scene you want to modify is changed with the selected section.
6 Press the OK button at the start point of the scene.
DVD-RW(VR) Scene No. 002 Start End Modify Scene Title List : 5/6

00:00:00 00:00:25

The image and starting point time are displayed on the Start window. Select the starting or ending point of the section you want to modify using the playback related buttons ( , , , , , , ).

English -77

01003A-R128,130-XEU_69~85 2/20/06 7:53 PM Page 78
Moving a Scene (Changing the Position of a Scene)
You cannot move the selected scene to the position of the next scene, because the selected scene should be inserted before that position, which requires no action. Depending on the kind of disc, the displayed screen may have a slight difference.
Press the buttons to select the scene you want to move (change the position), then press the OK button.
DVD-Recorder DVD-RW(VR) Scene No. 3/7 Edit Scene Playlist No. 3 Play Modify 01 00:00:00:00:00:00:04 Move Add 04 00:00:03 MOVE 05 00:00:11 OK 06 00:00:04 RETURN Delete EXIT

Adding a Scene

to select the 4 Press thethen pressbuttonsscene inserted scene that will have a new before it, the OK button.
A yellow selection window is displayed on the scene to be added as the new scene.
the buttons 5 Press the OK button. to select Move, then press
DVD-Recorder DVD-RW(VR) Scene No. 4/7
Edit Scene Playlist No. Play Modify 3

Deleting a Scene

Dolphin 01 Science 02 Sky 03 Dolphin Dolphin 7 Scene APR/23/2006 06:43 MOVE OK 04 Natural
Press the buttons to select the scene you want to delete, then press the OK button.
Press the buttons 3 press the OK button. to select Copy, then
Playlist that has been selected will be copied.
DVD-RW(VR) Dolphin No. Title 01 Science 02 Sky 03 Dolphin Dolphin 7 Scene 04 Natural 00:00:17 00:00:06 Play 00:00:06 Rename 00:00:37 Edit Scene Copy Delete RETURN EXIT Edit Playlist 3/4 Length Edit
the 5 Presspress buttons to select Delete, then the OK button.
DVD-Recorder DVD-RW(VR) Scene No. 2/6 Edit Scene Playlist No. 3 Play Modify 01 00:00:00:00:00:00:03 Move
APR/23/2006 06:43 MOVE OK
DVD-RW(VR) Dolphin No. Title 01 Science 02 Sky 03 Dolphin Dolphin 04 Natural 05 Dolphin
Edit Playlist 5/5 Length Edit 00:00:17 00:00:06 00:00:06 00:00:37 00:00:06
Add 04 00:00:11 MOVE 05 00:00:04 OK 06 00:00:05 RETURN Delete EXIT
7 Scene APR/23/2006 06:43 MOVE OK

English -79

01003A-R128,130-XEU_69~85 2/20/06 7:54 PM Page 80
You can create up to 999 scenes on one disc. In some cases, this may be different from the actual numbers. Press the MENU button after the operation has finished. The Edit Playlist screen will disappear.
Press the 3 then press buttons to select Delete, the OK button.
DVD-RW(VR) Dolphin No. 05 Title Science Sky Dolphin Natural Dolphin Edit Playlist 5/5 Length Edit 00:00:17 Play 00:00:06 00:00:06 Rename 00:00:37 Edit Scene Copy00:00:06 Delete

Dolphin 7 Scene

APR/23/2006 06:43 MOVE OK RETURN
Deleting a Playlist Entry from the Playlist
Using the PLAYLIST button
You will be prompted with the delete confirmation message Do you want to delete?.

DVD-RW(VR) Dolphin

Edit Playlist 5/5
DVD-RW(VR) Science No. 05 Title Science Sky Dolphin Natural Dolphin Edit Playlist 1/5 Length Edit 00:00:17 00:00:06 00:00:06 00:00:37 00:00:06

Do you want to delete?

APR/23/2006 06:43 MOVE OK RETURN EXIT

Science 1 Scene

the buttons 4 Press the OKbutton. to select Yes, then press
It automatically returned to the Edit Playlist screen after the delete operation has finished.

Deleting. (Please wait)

buttons the 2 Presstothe from theto select thentitle you want delete Playlist, press the OK or button.
DVD-RW(VR) Natural No. 03 04

Natural 1 Scene

Edit Playlist 4/4 Title Science Sky Dolphin Natural Length Edit 00:00:17 00:00:06 00:00:06 00:00:37

Troubleshooting..86 Specifications..90

86- English

01003A-R128,130-XEU_86~92 2/20/06 7:55 PM Page 87
Cannot play the disc. The angle operation does not work while playing a DVD disc.
Check whether the disc is inserted correctly with the label facing up. Check the regional code of the DVD disc. This DVD recorder cannot play some types of discs. (See pages 5, 49.)
The angle operation is available only when the disc contains images captured from different angles.
icon appears on the screen.
The selected audio and/or subtitle language is not played.
You cannot use this operation or function due to one of the following reasons: (1) Your DVD disc restricts it. (2) Your DVD disc does not support this feature (for example: angles) (3) The feature is not available at the moment. (4) You've requested a title, chapter, or scan time that is out of range.
Audio and subtitle languages are disc-specific. Only the sound and subtitle languages contained on the DVD disc are available and displayed in the disc menu.
Play mode settings are different from the settings configured in the Settings menu.
The disc does not support all selected functions. In this case, some settings configured in the settings menu may not work properly.
Cannot change the aspect ratio.
The aspect ratio is fixed for DVD discs. (See page 36)

English -87

01003A-R128,130-XEU_86~92 2/20/06 7:55 PM Page 88
The disc revolves, but no image or bad quality images are displayed.

Timer Recording

Timer lamp flickers.
Be sure that the Video Setting is properly set. (See pages 34-36) Check whether there is damage to or any foreign material on your disc. Some low quality discs may not play properly. If scenes change from dark to bright suddenly, the screen may shake vertically temporarily, but this is not a fault.
Check there is enough space in the disc for recording. Check whether the current disc is recordable or not. Make sure to check before the start time of recording.

Checkpoint 4

Timer recording does not work properly.

No sound.

Re-check the recording time and the end time settings again. Recording will be cancelled if the power is interrupted due to a power failure or another similar reason while recording.
Are you watching a programme in slow or skip mode? If you are playing a programme at a speed other than normal or fast 1 speed, sound will not be heard. Check the connections and settings. (See pages 21-22, 32-33) Check whether the disc is damaged. Clean the disc, if necessary. Check whether the disc is inserted correctly with the label facing up.

AK68-00683A-04_Cover

2005.12.10

12:13 AM

Page 1

XAA-ENG

Instruction Manual

DVD-R120

www.samsung.com

AK68-00683A-05

AK68-00683A-04(2~13)

2005.9.28

5:23 AM

Page 2

Getting Started

Warning

FCC NOTE (for U.S.A):
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help.
TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE THE COVER(OR BACK). NO USER-SERVICEABLE PARTS ARE INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This symbol indicates dangerous voltage inside the product that presents a risk of electric shock or personal injury.
This symbol indicates important instructions accompanying the product.
This unit can be used only where the power supply is AC 120V, 60Hz. It cannot be used elsewhere. This DVD recorder is designed and manufactured to respond to the Region Management Information. If the Region number of a DVD disc does not correspond to the Region number of this DVD recorder, the DVD recorder cannot play the disc. This device is protected by U.S. Patent Nos.4,631,603;4,577,216;4,819,098;4,907, 093; and 6,516,132.This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights.Use of this copyright protection technology must be authorized by Macrovision,and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision.Reverse engineering or disassembly is prohibited.
Do not install this equipment in a confined space such as a bookcase or similar unit. WARNING : To prevent damage which may result in fire or electric shock hazard, do not expose this appliance to rain or moisture. CAUTION : DVD RECORDERS USE AN INVISIBLE LASER BEAM WHICH CAN CAUSE HAZARDOUS RADIATION EXPOSURE IF DIRECTED. BE SURE TO OPERATE RECORDER CORRECTLY AS INSTRUCTED.

CAUTION

8- English

Page 9
Before reading the users manual
Make sure to check the following matters before reading the users manual.
How to use the DVD recorder

Step 1

Select the disc type
Icons that will be used in manual Icon Term DVD Definition This involves a function available in DVD or DVD-R/DVD-RW discs that have been recorded and finalized in Video Mode. This involves a function available in DVD-RAM. This involves a function available in DVD-RW. This involves a function available in DVD-R. This involves a function available in a data CD (CD-R or CD-RW). This involves a function available in a data picture CD (CD-R or CD-RW). This involves a function available in a data CD (CD-R or CD-RW on which MP3 is recorded). This involves a case where a function does not operate or settings may be cancelled. This involves tips or instructions on the page that help each function operate.
This unit can record on the following types of discs. If you want to repeatedly record on the same disc or you want to edit the disc after recording, select a rewritable DVD-RW or DVD-RAM type disc. If you want to save recording without any change, choose a non-rewritable DVD-R.

RAM RW R CD JPEG

Step 2
Format the disc to start recording

Caution

Unlike a VCR, the recorder automatically starts formatting when an unused disc is inserted. This is required for the preparation of recording on a disc. Using a DVD-RAM This type of disc can be formatted in DVD-Video Recording format (VR mode). You can edit recorded image and create a playlist and edit images in a specific sequence according to your requirements. Using a DVD-RW This type of disc can be formatted in either DVD-Video format (Video mode) or DVD-Video Recording format (VR mode). For an unused disc, a message that asks whether to initialize in VR Mode or not is displayed. You can play a Video mode disc on various DVD components. A VR mode disc allows more varied editing. Using a DVD-R This type of disc can be formatted in DVD Video format. After formatting is complete, you can record on the disc. You can play this type of discs on various DVD components only when they have been finalized.

Setup using 2 Selectthe ENTER orthe buttons, then press button.
Timer Rec. Setup System Language Audio Video Parental Control Setup
If you have the Antenna connected via Method 1 or 3 on pages 15-17. The DVD Recorder automatically sets the clock by searching for a channel that carries a time signal and sets your time zone and daylight saving(if applicable).
Auto Clock Set the 5 Selectpress the ENTERusing button. buttons, then or or 6 Press the ENTERthe button. then press Select On using buttons, the ENTER or button.
Timer Rec. Setup Auto Clock Set Clock Data CH Time Zone Daylight Saving Auto Clock Set Off : On On : Automatic : Automatic : Automatic
Select System using buttons, 3 press the ENTER or thebutton. then
System menu will be displayed.
Timer Rec. Setup Clock Set Channel Set CM Skip Time EP Mode Time Chapter Creator : 15 Sec : 6Hours : Off System
The Menus are slightly different depending on whether a disc is inserted or not. The menus described on the next few pages are with no disc in the unit.

English -29

Page 30
If your clock is set to the wrong time zone or daylight saving, you can adjust these settings without tuning off the Auto Clock Set function.
Daylight Saving Select Yes, No or Automatic using the buttons then press the ENTER or button. q Select Automatic to set the daylight saving automatically
Auto Clock Set Auto Clock Set Clock Data CH Time Zone Daylight Saving : On : Automatic : Automatic : Automatic No Yes
the sub menu(Clock Data CH, Time 7 Selector Daylight Saving) using the Zone buttons, then press the ENTER or button.
Timer Rec. Setup Auto Clock Set Clock Data CH Time Zone Daylight Saving
Auto Clock Set : On : Automatic : Automatic : Automatic

Method 2

MOVE SELECT RETURN EXIT
If you have the Antenna connected via Method 2 on page 16.
Clock Data CH Select a channel that carries a time signal using the buttons then press the ENTER button. q Select Auto to set the clock data channel automatically.

Manual Clock Set

If your clock cannot be set automatically, set the clock manually.
Timer Rec. Setup Select channel :

Clock Data CH

To setup, follow the steps 1 to 4 in page 29.
Clock Set using 5 Select Manualpress the ENTERthe button. buttons, then or
Time Zone Select the time zone of your area using the buttons then press the ENTER or button. q Select Automatic to set the time zone automatically.
Auto Clock Set Automatic Atlantic Eastern Central Mountain Pacific Alaska Hawaii

30- English

Page 31
the buttons to select 6 UsingtheDate andbutton. Time, andthe Current Current then press ENTER
When the current time is stored in memory and then the set is powered off, the current time will appear in the front panel display.

3. Channel Set

Auto Channel Memory
You can set the Antenna/Cable TV settings automatically.
Timer Rec. Setup Date (mm/dd/yy)
Timer Record Timer Record Scheduled Record List
Time 12 : 00 AM Timer Rec. Setup

01 / 01 / 2005 SAT

: Sets the value You can set the value using the number (0~9) buttons. : Moves to items
Timer Rec. Setup System Language Audio Video Setup
If any of number buttons on the remote control do not operate, press the DVD button and try again.

Parental Control

Channel set using buttons, 4 Selectpress the ENTER orthebutton. then
Select 5 ENTERAntenna/Cable TV(Signal Source) using the buttons, then press the or button.
Timer Rec. Setup Antenna/Cable TV Auto Channel Memory Channel Add/Delete Channel Set : Cable TV

English -31

Page 32
Select the item that matches the antenna connection you selected on pages 15~17(Method 1, 2 and 3).

Manual Channel Set

Methods 1 and 3
To setup, follow the steps 1 to 5 in page 31.
Manual Channel Set can be used after you have first selected Auto Channel Memory. Use the Manual Channel Setting to delete unnecessary channels after using the Auto Channel Memory.
Select Antenna using 6 press the ENTER or the buttons, then button.
Timer Rec. Setup Antenna/Cable TV Auto Channel Memory Channel Add/Delete Channel Set : Cable TV Antenna Cable TV

English -35

AK68-00683A-04(36~46)

5:24 AM

Page 36

Before Recording

This section shows various DVD recording methods.
This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference.

Recordable discs

This recorder can record on the following discs.

DVD-RAM

DVD-RW
DVD-RWs and DVD-RAMs are rewritable. DVD-Rs are non-rewritable
Compatibility between Samsung and Other Companies' Recorders
Disc Types DVD-RAM Recording format VR Mode Recording Device Samsung Other Company Samsung VR Mode Other Company DVD-RW Samsung V Mode Other Company Samsung DVD-R V Mode Other Company Finalizing X X finalized not finalized finalized not finalized finalized not finalized finalized not finalized finalized not finalized finalized not finalized Additional Recording in Samsung Recorder Recordable Recordable Not recordable Recordable Not recordable Recordable Not recordable Recordable Not recordable Not recordable Not recordable Recordable Not recordable Not recordable
Finalize - This closes the DVD-R/RW so no additional recording can be done. Unfinalize - This allows additional recording on a DVD-RW disc originally recorded on the DVD-R120. - A DVD-RW disc that has been recorded by DAO(Disc At once) in a PC cannot be unfinalized. - A DVD-RW disc that has been recorded in Video Mode of a different makers recorder cannot be unfinalized. - A DVD-R disc cannot be unfinalized.
Before Recording..36 Recording the current TV program you are watching..38 Recording from external equipment.40 Copying from a Camcorder..41 Making a One Touch Recording (OTR)..42
Setting a Timer Recording..43 Flexible Recording (only for Timer recording).44 Editing the Scheduled Record List..44 Deleting the Scheduled Record List.45 Recording the Scheduled Record List..46

36- English

Page 37

Recording Formats

Since available functions differ depending on the disc type, select a disc that best fits your preferences; When you insert an unused disc, the following message appears DVD-RAM: Use after formatting the disc.

Characteristic

Recording Times Data Rates Approx. 1 hour about 8 Mbps Approx. 2 hours about 4 Mbps Approx. 4 hours about 2 Mbps Approx. 6 hours/ about 1.2 Mbps Approx. 8 hours/ about 0.8 Mbps
XP Select when the (high quality mode) video quality is important. SP Select to record in (standard quality mode) standard quality.
Unformatted Disc Do you want to format this disc? Yes No
Select when a long LP recording time is (long recording mode) required. EP (extended mode) Select when a longer recording time is required.

Press the STOP ( ) button to stop or finish a recording in progress. q When using DVD-RAM/DVD-RW/DVD-R discs, the message Updating the information of disc. Please wait for a moment is displayed.

To pause recording

Press the play/pause ( progress. Press the play/pause ( recording. ) button to pause a recording in ) button again to resume a

SP LP EP XP

Record Mode SP (02:12)
You can not change the recording mode and the channel while recording. Recording will stop automatically if there is no free space left for recording. Up to 99 titles can be recorded onto a disc. Recording will stop automatically if a copy protected image is selected. If you are using a Cable Box(no antenna), you cannot watch a different cable TV program from the one you're recording. DVD-RAM/DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit.

Press the REC button.

Information concerning the channel is displayed on the screen and then recording begins. Icon( ) is displayed on the front panel.

Recording : CH 7 [Mono]

To view the current status of the disc and progress of recording : Press the INFO button, and the information about the disc will appear.
DVD-RAM(VR) Disc Name Total Title Total Playlist Recordable Time Protection Screen APR SUN Disc Info 02:00 SP Not Protected Recording CH 7 [Mon] 12:00 AM
Press the INFO button once again to view information about the recording.

DVD-RAM(VR) Name

Recording Info APR/04/2005 12:00 AM CH7 Recording Title 15 Created Time APR/04/2005 12:00 AM Recording Time 00:02:05 APR SUN 12:00 AM

English -39

Page 40
Recording from external equipment

5 Press the REC button.

Press the STOP ( ) button to stop or finish a recording in progress. q When using DVD-RAM/DVD-RW/DVD-R discs, the message Updating the information of disc. Please wait for a moment is displayed
Check that the disc has enough available space for the recording. Adjust the recording mode.
Press the OPEN/CLOSE button, and place a recordable disc on the disc tray.
You can not change the recording mode and input source while recording. Recording will stop automatically if there is no free space left for recording. Up to 99 titles can be recorded onto a disc. Recording will stop automatically if a copy protected image is selected. DVD-RAM/DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit.

2 Press the REC button to start recording.

OTR Mode 0:30

OTR is going to be ended soon and power will be turned off automatically. Press [ENTER] button to continue to use DVD-Recorder. OK
Press the REC button to adjust the recording time.

0:30 1:00 . 8:00 off

Press the STOP ( ) button. The message Do you want to stop recording? is displayed.
The timer counter decreases minute 8:00 to 0:00, then the DVD Recorder stops recording.
Do you want to stop recording?
Press the buttons to select Yes, and then press the ENTER button.

42- English

Page 43
Setting a Timer Recording
Source: The video input source (L1, L2), or the broadcasting channel you want to make a timer recording of. When selecting channels to be recorded, the buttons on the remote control can let you select only the channels that have been memorized during Auto Scan. For the selection of other channels, use the number buttons. Date: Date that the timer recording starts 01/01 01/02 01/30 01/31 Every Day MON-SAT MON-FRI Every SAT Every SUN
You need to set clock (Setup Clock Set) before proceeding with a timer recording. (See page 29)
Start/End Time: Start and end time of the timer recording Mode (Recording mode) XP (High quality): Approx. 1 hour SP (Standard quality): Approx. 2 hours LP (Long recording): Approx. 4 hours EP (Extended): Approx. 6 hours or 8 hours. FR (Flexible Recording): See page 44.
3 Press the MENU button in stop mode.
When you are recording at EP mode on a DVD-RW(V)/R disc, it may not record the full 6 or 8 hours because the unit uses the VBR(Variable Bit Rate) ENCODING system. For example, if you record a program with a lot of action, it uses a higher bit rate which in turn consumes more disc memory.
You can also set a timer recording via the TIMER button.
7 Press the ENTER button.

DVD-RAM(VR)

Scheduled Record List Recordable Time 02:12 SP No. Source CH 09 -- -Date 01/01 --/-Start End Mode Edit 12:00 AM 02:00 AM SP --:-- -- --:-- -- --
the 4 Pressthen pressbuttons to selectTimer Rec., and the ENTER or button.

Title List Playlist Disc manager Timer Rec. Setup Timer Record Scheduled Record List Timer Record
( ) and Timer Set will appear on the front panel display. This means that a timer recording is set. Recording is automatically performed when the set time is reached.
buttons select Timer 5 Press theand then presstothe ENTER or Record, button.
The Timer Record Input items are displayed.
Scheduled Record List Recordable Time 02:12 SP No. 01 Source -- -Date Start End Mode Edit --/-- No. 01 -- --:-- -- ---:-Start End Mode

If you make a mistake

Press the button to select the item you want to change.
If the timer settings overlap
The programs are recorded in order of priority. If timer recording is set for the first program and then again for the second program and both programs overlap, the following message will appear on the screen: This setting is identical with 1 The message shows that the first program has priority. After recording of the first program is complete, the second program starts being recorded.

Source Date

CH 09 01/: 00 AM 02 : 00 AM SP Recordable Time 02:12 SP
Fill in the items using the buttons.
: Moves to the previous/next item, 0~9 : Sets a value.
To exit without saving the current setting
Press the MENU or TIMER button.
To return to the previous menu
Press the RETURN button if you don't want to set a timer recording.

English -43

Page 44
The timer recording time may differ from the set time depending on the disc and the overall timer recording status (for example, recording times overlapping, or when the previous recording ends within 3 minutes of the start of the next recording.) will start blinking if Timer Recording is not ready to start.
to select 3 Press the buttonspress the Scheduled Record List, and then ENTER or button.
Scheduled Record List Recordable Time 02:12 SP No. 03 Source CH 09 CH 05 -- -Date 01/01 01/01 --/-Start End Mode Edit 12:00 AM 02:00 AM SP 12:30 AM 09:00 PM LP --:-- -- --:-- -- --
Flexible Recording (for Timer recording only)
the buttons select number 4 Pressand then press thetoENTERthewantbutton. of the Scheduled Record List you to edit, or
The Edit and Delete items are displayed.
Scheduled Record List Recordable Time 02:12 SP No. 03 Source CH 09 CH 05 -- -Date 01/01 01/01 --/-Start End Mode Edit 12:00 AM 02:00 AM SP Edit 12:30 AM 09:00 PM LP Delete --:-- -- --:-- -- --

No sound is heard during Scan(Search) mode, except CDs (CD-DA).

English -49

Page 50
Searching Chapters or Tracks

About ANYKEY

During play, you can search quickly through a chapter or track.

CM DIS

ENU TITLE ME NU

If you press the button,

it moves to the beginning of the chapter or track or marker(DVD-RAM, DVD-RW(VR mode)). Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker(DVD-RAM, DVD-RW(VR mode)).
The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, track, and time. You can also change the subtitle and audio settings and set some features including Repeat, Angle, and Zoom.
it moves to the next chapter or track or marker(DVDRAM,DVD-RW(VR mode)).
Moving to a scene directly using the ANYKEY
If you want to move to a title, a chapter or a track to find a desired scene.

Slow Motion Play

step mode, press 1 In pause orthe remote control.the button on
1 Press the ANY KEY button during playback.

DVD-VIDEO

Title Chapter Time
Slow 1/8 Slow 1/4 Slow 1/2
1/10 1/40 00:01:45 Off ENG Off 1/1 Off CHANGE D 5.1CH
Subtitle Audio Repeat Angle Zoom
To return to normal speed playback, press the button.
Press and hold the button during pause, and the disc will play slowly at a 1/4 speed. If the button is released, the pause operation will resume.
2 Press theor buttons to select the Title, Chapter Track.
Title Chapter Time Subtitle Audio Repeat
The speed marked in this function may be different from the actual playback speed.

Step Motion Play

Angle Zoom
Press the button on the remote control in the still mode.
Each time the button is pressed, a new frame will appear. When is pressed, the previous frame will be activated. When is pressed, the next frame will be activated. To return to normal speed playback, press the button.
buttons number 3 Press thetoselectENTERorbutton. (0~9) buttons the desired scene. Then, press the

50- English

Page 51
If you want to move to a desired time to help you find a scene. Press the ANY KEY button during playback.
Using the Repeat Function
Playing Repeatedly(Repeat Playback)
Title Chapter Time Subtitle Audio Repeat Angle Zoom

Using the REPEAT button

1 Press the REPEAT button during playback.

Repeat

2 Press the buttons to select the Time.
1/10 1/40 00:01:45 Off ENG Off 1/1 Off NUMBER D 5.1CH
the REPEAT button 2 Press to play repeatedly. or press theyou buttons to select the Title or Chapter want Press the ENTER button.

Marker N:10

Audio CD(CD-DA) Screen Elements
Music Repeat : Off 01. TRACK 1 01. TRACK 1 02. TRACK 2 03. TRACK 3 Play Option : Normal 00 : 52 4:39 4:31 4:30 3:53 4:23 4:24 MENU

Marker 09 N:9

& $ % ^

04. TRACK 4 01/12

MOVE SELECT

05. TRACK 5 06. TRACK 6

When a marker is cleared while DVD-RAM/-RW (VR mode) is playing, marker numbers will change. For example, if the 7th marker is cleared after ten markers are registered, the marker numbers after the eighth will automatically move ahead by one and the 8th marker becomes the 7th.
1. Repeat mode: Repeat off/Repeat Track/Repeat Disc 2. Current track (song): Displays the number of the track currently being played. 3. Displays the current play index and total track number. 4. This shows the operating state of a disc and a playback time corresponding to a portion that is currently played. 5. Displays the track list (song list) and the playing time of each track. 6. Button display. 7. Play Option: Normal, Random, Intro or Playlist

English -57

Page 58
Buttons on the Remote Control used for MP3 playback

Playing an MP3 Disc

1 Insert an MP3 Disc into the disc tray.
The MP3 menu appears and the tracks(songs) are played automatically.
Repeat : Off Straight from the heart ROOT Bryan Adams Bryan Adams_2 Straight from the heart
Music Play Option : Normal 00 :22

ROOT 03/06

Run to you Heaven SELECT RETURN MENU
Press select the track 2-1 (song)thebuttonbuttons toand then press the you want to hear, ENTER or button.
1. , 0~9: Selects a track (song). 2. : Plays the selected track (song). 3. ENTER button: Plays the selected track (song). 4. ( ) button: Plays the next track. 5. ( ) button: Returns to the beginning of the current track when pressed during playback. If pressed again, your DVD recorder moves to and plays the previous track. If you press this button within three seconds after playback starts, the previous track will be played. If you press this button after three seconds, the current track will be replayed from the beginning. 6. Press the ( / ) button: Fast Play (X2, X4, X8) 7. : Stops a track(song). 8. : Plays a track(song) or pauses playback. 9. ANYKEY: To select the top menu on screen display (Repeat or Play Option).
Press the number buttons 2-2 track (song) and the track to selectisthe (song) played automatically.

MP3 Screen Elements

Music Repeat : Off Play Option : Normal 00 :22 ROOT Bryan Adams Bryan Adams_2 Straight from the heart

Straight from the heart

& $
Run to you Heaven SELECT RETURN
1. Repeat mode: Repeat off, Repeat Track, Repeat Folder or Repeat Disc 2. Current track (song): Displays the name of the track being played. 3. Displays the current folder and play index. 4. This shows the operating state of a disc and a playback time corresponding to a portion that is currently played. 5. Displays the information for the folder and its tracks. 6. Button display. 7. Play Option : Normal, Random, Intro or Playlist

Repeat : On 01. TRACK 1 01. TRACK 1 02. TRACK 2 03. TRACK 3 04. TRACK 4 01/12 05. TRACK 5 06. TRACK 6 SELECT RETURN Music Play Option : Normal 00 : 52 4:39 4:31 4:30 3:53 4:23 4:24 MENU
Select Playlist using the buttons, and then press the ENTER button.
The Playlist screen will appear.
Select tracks in the order in which you want them to play using the buttons. Press the ENTER button.
Repeat : On Music Play Option : Playlist 00 : 00 01. TRACK 1 02. TRACK 2 03. TRACK 3 04. TRACK 4 05. TRACK 5 06. TRACK 6 MOVE SELECT MENU 01. P_TRACK 1 02. P_TRACK 2 03. P_TRACK 3 04. P_TRACK 4
only) or 1 Insert a Picture CD(JPEG disc tray.Mixed CD(JPEG + MP3)into the playing press the 2 Whenbutton. a Mixed CD, press the ENTER buttons to select Photo and or
(When playing a Picture CD, see number 3 on the next page.)
wrong trank, press the 3 If you playlisted apress buttons to select button, then press the wrong track and the CANCE button.
The wrong track will be removed.
Repeat : On P_TRACK 1 01. TRACK 1 02. TRACK 2 03. TRACK 3 04. TRACK 4 05. TRACK 5 06. TRACK 6 MOVE SELECT CANCEL MENU 01. P_TRACK 1 02. P_TRACK 2 03. P_TRACK 3 Music

JPEG+MP3

Photo Music Timer Rec. Setup Press [ENTER] or Right button: Photo
Play Option : Playlist 01 : 36
4 Press the PLAY button to playback the playlist.

60- English

Page 61
3 Press the buttons to select a picture.
Index 6 / 73 Photo Slide Show ROOT / DSC01189

Playing the Title List

Page 2 / MOVE SELECT

13 RETURN MENU

Follow these instructions to play back a scene from the Title List.
To see the next 6 pictures, press the button. To see the previous 6 pictures, press the button.
Using the TITLE LIST button
-1 If your press the PLAY( ) button, the Slide show screen will appear.
The picture interval (Slide show speed) must be set.
1 Press the TITLE LIST button.
The Title List screen is displayed.
Title List No. Title Length Edit
Slide Show Speed 01 APR/19/00:00:APR/19/00:00:APR/20/00:00:15 DSC01189 APR/19/2005 12:00 AM CH12 MOVE SELECT RETURN APR/19/2005 12:00 AM MOVE SP SELECT 04 APR/20/00:00:APR/21/00:06:APR/21/00:08:APR/22/00:09:36 RETURN EXIT

62- English

Page 63
Title List Screen Elements

DVD-RAM(VR) DVD-RAM(VR)

Title List Title List Length Edit 00:00:21 00:00:03 00:00:15 Play 00:00:16 Rename Delete 00:06:32 Edit 00:08:16 Protection 00:09:36 EXIT

Length Edit Title No.

01 APR/19/00:00:21 01
APR/19/2005 12:00 AM CH12 APR/19/2005 12:00 AM MOVE
02 APR/19/00:00:03 APR/20/00:00:Sports 04 APR/20/00:00:Movie 05 APR/21/00:06:02/01/01 APR/21/00:08:SP 00:25:30(PM) 07 APR/22/SP 00:09:07
SELECT MOVE RETURN SELECT EXIT RETURN
& ! Playback screen for recorded entries. @ Information window for the selected entry: Title name, recording date, recording time, lock status, recording mode # Recorded entry No. $ Recorded entry title % Recording length (i.e., the playing time) ^ Title list edit items Play: Plays the selected entry. Rename: Renames the title of a selected entry. Delete: Deletes the selected entry from the list. Edit: Deletes a section. Protection: Locks or unlocks the selected entry. & Button display.
This may depend on the the disc type. DVD-R/DVD-RW(Video) has limited editing function.

English -63

Page 64

Using the Setup Menu

Settings& Adjustments
For ease of use, we recommend that you set up the initial settings before using the product.
disc mode, 1 With the unit in Stop mode/No remote control. press the MENU button on the
Menu items differ depending on the disc type.
Setup menu will be displayed.

Settings&Adjustments

System Setting Setup of the General Options. - Clock Set, Channel Set, CM Skip Time, EP Mode Time, Chapter Creator Language Setting Setup of the Language Options. - Audio, Subtitle, Disc Menu, On-Screen Menu Audio Setting Setup of the Audio Options - Digital Output , DTS, Dynamic Compression Video Setting Setup of the Display Options. Use to select which type of screen you want to watch and several display options. - TV Aspect, Input Level, Black Level, 3D Noise Reduction, Front Display Parental Control Setup of the Parental Level Allows users to set the level necessary to prevent children from viewing unsuitable movies such as those with violence, adult subject matter, etc. - Password, Rating Level,Change Password

Title List Playlist Disc manager Timer Rec. Setup New Playlist Edit Playlist Playlist
- To make a new playlist -
the 6 Presspress buttons to select Make, and then the ENTER button.
A new Scene will be added to the current Playlist. A new Make Scene screen is displayed. Repeat the above steps to create further scenes.
If you want to make a new playlist, go to MENU new playlist. You can check and see all the scenes on Edit Playlist screen.
the 3 Pressthen pressbuttons to selectNew Playlist, and the ENTER or button.
The Make Scene screen is displayed.
Make Scene Scene No. 001 Start
- To return to Edit Playlist menu -

Make Return EXIT

the 7 Presspress buttons to select Return, and then the ENTER button.
The Edit Playlist screen is displayed.
No. Title Edit Playlist Length Edit
01 APR/23/2005/0 00:00:APR/23/2005/0 00:00:APR/24/2005/1 00:00:APR/24/2005/1 00:00:16
Press the ENTER button at the start point.
Make Scene Scene No. 001 Start End Make Return EXIT
APR/25/2005 06:03 AM 7 Scene APR/23/2005 06:43 AM MOVE SELECT
05 APR/25/2005/2 00:06:32
You can create up to 99 playlist entries. Depending on the kind of disc, the displayed screen may have a slight difference. Press the MENU or PLAY LIST button after the operation has finished. The Edit Playlist screen will disappear.
The image and time at the start point are displayed on the Start window. The yellow-colored selection bar moves to the End item. Select the starting point of the section from which you want to create a new scene using the playback related buttons ( , , , , ).

English -77

Page 78
Playing Entries in the Playlist
Follow these instructions to play the playlist entries.
3 Press the buttons to select Play, and then select the ENTER button.
The playlist entries will be played.
Edit Playlist No. Title Length Edit
01 APR/23/2005/0 00:00:APR/23/2005/0 00:00:03
With the unit in stop mode, press the PLAY LIST button.
03 APR/24/2005/0 00:00:15 Play 04 APR/24/2005/1 00:00:16 Rename APR/23/2005 06:43 AM 7 Scene APR/23/2005 06:43 AM MOVE SELECT RETURN
Edit Scene 05 APR/25/2005/2 00:06:32 Copy Delete EXIT
01 APR/23/2005/0 00:00:APR/23/2005/0 00:00:APR/24/2005/0 00:00:APR/24/2005/1 00:00:16 APR/23/2005 06:43 AM 7 Scene APR/23/2005 06:43 AM MOVE SELECT RETURN EXIT 05 APR/25/2005/2 00:06:32