Disc Storage

Be careful not to harm the disc because the data on these discs is highly vulnerable to the environment. Do not keep under direct sunlight. Keep in a cool ventilated area. Store vertically. Keep in a clean protection jacket. If you move your DVD Recorder suddenly from a cold place to a warm place, condensation may generate on the operating parts and lens and cause abnormal disc playback. When this occurs, do not connect the plug to the power outlet. Wait for two hours, then insert the disc and try to playback again. It will work properly when condensation has evaporated.

Using MPEG4 disc

Disc : CD-R/-RW, DVD-R/-RW MPEG4 File with following extensions can be played. :.avi,.divx,.AVI,.DIVX MPEG4 Codec format : DivX 3.11 DivX 4.x DivX 5.x Available Audio Format : MP3, MPEG, PCM, AC3, DTS Supported subtitle file formats:.smi,.srt,.sub,.psb,.txt,.ass

Disc Specifications

Using CD-R/-RW

DVD-Video

A digital versatile disc (DVD) can contain up to 135minutes of images, 8-language audio and 32 subtitle languages. It is equipped with MPEG-2 picture compression and Dolby 3D surround sound, allowing you to enjoy vivid and clear theater quality images in the comfort of your own home. When switching from the first layer to the second layer of a double-layered DVD Video disc, there may be momentary distortion in the image and sound. This is not a malfunction of the unit. Once a DVD-R/-RW recorded in Video Mode is finalized, it becomes DVD-Video.
Use a 700MB(80 minutes) CD-R/-RW disc. If possible, do not use a 800MB(90 minutes) or above disc, as the disc may not play back. If the CD-R/-RW disc was not recorded as a closed session, you may experience a delay in the early playback time, and all recorded files may not play. Some CD-R/-RW discs may not be playable with this unit, depending on the device which was used to burn them. For contents recorded on CD-R/-RW media from CDs for your personal use, playability may vary depending on contents and discs.

Step 5

Editing a recorded disc
Editing on discs is easier than editing on conventional video tapes. The recorder supports many different edit functions, possible only with DVDs. With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title. Creating a playlist (DVD-RW in VR mode) With this recorder, you can create a new playlist on the same disc and edit it without changing the original recording.

10 - English

Page 11

Description

Front panel
1. POWER Turns the recorder on and off. 2. AV 2 IN Connect external equipment. 3. DV IN Connects external digital equipment with a DV jack. (such as a camcorder) 4. DISC TRAY Opens to accept a disc. 5. P.SCAN Selects the progressive scan mode. 6. OPEN/CLOSE Opens and closes the disc tray.
7. DISPLAY Displays the playing status, time, etc. 8. CH ( ) Select TV channels. 9. REC Starts recording. 10. STOP Stops disc playback. 11. PLAY/PAUSE Plays a disc or pauses playback. 12. SEARCH Go to the next title/chapter/track, or goes back to the previous title/chapter/track.

Front Panel Display

1. Lights when a disc is loaded. 2. Lights in the record mode. 3. Lights to indicate the timer record mode.
4. Lights when a DVD-R/-RW/-RAM disc is loaded. 5. Alpha/Numeric display. 6. Lights in the progressive scan mode.

English - 11

Page 12
Rear Panel Getting Started
1. ANT IN/ANT OUT (TO TV) Connect antenna cables. 2. DIGITAL AUDIO OUT(OPTICAL) Connects to an amplifier having a digital optical audio input jack. 3. DIGITAL AUDIO OUT(COAXIAL) Connects to an amplifier having a digital coaxial audio input jack. 4. AV AUDIO OUT Connect to the audio input of external equipment using audio cables. 5. AV VIDEO OUT(good video quality) Connects the input of external equipment using a Video cable. 6. AV S-VIDEO OUT(better video quality) Connects the input of external equipment using an S-Video cable.
7. COMPONENT VIDEO OUT(best video quality) Connect to equipment having Component video input jacks. 8. AV 1 AUDIO IN Connect the output of external equipment using audio cables 9. AV 1 VIDEO IN Connects the output of external equipment using a video cable. 10. AV 1 S-VIDEO IN Connects the output of external equipment using an S-Video cable. 11. HDMI OUT
The Antenna connection does not pass audio/video signals. To watch a DVD on your TV, you must connect audio/video cables.

8. CM SKIP Button

The unit can be set to automatically skip a portion of the program during playback of a DVD disc.

9. MARKER Button

Use this to bookmark or mark a position while playing a disc.
This is a special remote control for the visually impaired, and has Braille points on the POWER( PLAY( ) buttons.

), STOP(

English - 13

R135-XAA-ENG-14-29

Page 14
Connecting & Setting Up
This section involves various methods of connecting the DVD Recorder to other external components and setting required initial modes.

Quick Overview

A Quick Overview presented in this guide will give you enough information to start using the recorder.
Step 1 : Connecting the Antenna Cable
Step 2 : Connecting the Video Cable
Step 3 : Connecting the Audio Cable
Step 4 : Connecting HDMI/ DVI to a TV
Step 5 : Connecting External Devices
Step 6 : Connecting the Power Cord
Step 7 : Preparing the Remote Control
Quick Overview.14 Step 1 : Connecting the Antenna Cable.15 Step 2 : Connecting the Video Cable.18 Step 3 : Connecting the Audio Cable.21 Step 4 : Connecting HDMI/ DVI to a TV.24 Step 5 : Connecting External Devices.26 Step 6 : Connecting the Power Cord.29 Step 7 : Preparing the Remote Control.29
Note to CATV system installer: : This reminder is
provided to call CATV system installers attention to Article 820-40 of the National Electrical Code (Section 54 of Canadian Electrical Code, Part I), that provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building as close to the point of cable entry as practical.

14 - English

Page 15
Step 1: Connecting the Antenna Cable
There are several ways to connect your DVD Recorder. Select one of the Antenna connections on the following pages.
Antenna + DVD Recorder + TV : No Cable box
You can record non-scrambled channels by selecting the channel on the DVD Recorder. Also use this method if you watch channels without cable box.

Audio : For the disc audio language. Subtitle : For the disc subtitles. Disc Menu : For the disc menu contained on the disc. On-Screen Menu : For the unit menu of your DVD recorder.
Select the desired language using the buttons, then press the ENTER or button.
No Disc Timer Rec. Setup Audio Subtitle : Original Original
English : Automatic Franais Disc Menu : English Deutsch On-Screen Menu : English Espaol Italiano Nederlands Korean ENTER RETURN
Select Setup using the buttons, then press the ENTER or button
Press the RETURN or button to return to the previous menu. Press the MENU button to exit the menu. The selected language will only appear if it is supported on the disc.

40 - English

12:40 PM

Page 41

Video (Display) Setting
Select the sub menu(TV Aspect,Input Level, Black Level, 3D Noise Reduction, HDMI/DVI Resolution or DivX(R) Registration) using the buttons, then press the ENTER or button.
TV Aspect: see page 36 Input Level: Adjusts the level of the input signal.
No Disc Timer Rec. TV Aspect Setup Input Level Black Level 3D Noise Reduction : 16:9 Wide Darker : Darker Lighter IRE : 7.5 : Off : 480P
Darker : If you feel the screen is too light and you want to make the screen darker.
Lighter : If you feel the screen is too dark and you want to make the screen lighter. Black Level: Adjusts the black level of the screen.
Setup No Disc Timer Rec. Setup TV Aspect Input Level Black Level 3D Noise Reduction HDMI/DVI Resolution DivX(R) Registration : 16:9 Wide : Darker 0 : 7.5 IRE IRE 7.5 Off : IRE : 480P
0 IRE : Select this when you want to make the screen darker.
Video option menu will be displayed.
7.5 IRE : Select this when you want to make the screen lighter.
Black level function is not available in the progressive scan mode.
3D Noise Reduction (motion adaptive noise reduction)
EXIT No Disc Timer Rec. TV Aspect Input Level Black Level 3D Noise Reduction : 16:9 Wide : Darker : 7.5 IRE
No Disc Timer Rec. TV Aspect Setup Input Level Black Level 3D Noise Reduction HDMI/DVI Resolution DivX(R) Registration : 16:9 Wide : Darker : 7.5 IRE : Off : 480P
Off Off : HDMI/DVI Resolution On 480P : DivX(R) Registration
On : Select to remove noise from the screen.

Off : Normal

English - 41
01049A-R135-XAA-ENG-30-44

2006.3.14

10:3 AM

Page 42

HDMI/DVI Resolution This setting is used when the unit is connected by HDMI or DVI with Display devices (TV, projector, etc).
No Disc Timer Rec. Setup TV Aspect Input Level Black Level 3D Noise Reduction HDMI/DVI Resolution DivX(R) Registration : 16:9 Wide : Darker : 7.5 IRE : Off 480P : 480P 720P 1080i MOVE ENTER RETURN EXIT

Parental Control

The Parental Control function works in conjunction with DVDs that have been assigned a rating - which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

480p : 720 x 480 720p : 1280 x 720 1080i : 1920 x 1080
Output selection System Setup
Connect the DVD-R135 to your TV via HDMI or DVI. Set your TV's input to HDMI or DVI. Press the P.SCAN button while the unit is in stop mode to select the output resolution. - If your TV is connected the HDMI or DVI cable, the output resolution mode changes in the following sequence each time you press the P.SCAN button: 480p 720p 1080i - If your TV is connected the AV or component cables (without HDMI/DVI cable), the output resolution mode toggles 480p/480i in turn.
Even if HDMI/DVI cable is connected to your TV, the AV connection outputs only 480i and the component connection outputs only 480p irrespective of the on screen display.
No Disc Timer Rec. Setup System Clock Set Channel Set Language Audio Video Parental Control
DivX(R) Registration Please use the Registration code to register your DVD Recorder with the DivX(R) Video On Demand format. To learn more, visit www.divx.com/vod
Select Parental Control using the buttons, then press the ENTER or button.
Use the buttons to select the desired item. Then press the ENTER or button.
Press the RETURN or button to return to the previous menu. Press the MENU button to exit the menu. IRE: Short for the Institute of Radio Engineers. An IRE unit is a relative unit of measure equaling 1/140th of the peak-topeak (p-p) video amplitude.

42 - English

Page 43
The first time the Parental Control is accessed, the Create the Password message will be displayed.
Create a 4-digit password using the 0 to 9 buttons on the remote control.
No Disc Timer Rec. Setup Create the password Parental Control

Setting the Rating Level

Select Rating Level using the buttons.
No Disc Timer Rec. Setup Password Rating Level Change Password : On : Level 1 Kids
EXIT MOVE ENTER RETURN EXIT
The Re-enter Password screen appears to confirm the password. Enter your password again.
No Disc Timer Rec. Setup Confirm the password Parental Control
Press the ENTER or button.

No Disc Timer Rec. Setup

Level 8 Adults : On Level 7 : Level 1 Kids Level 6 Change Password Level 5 Level 4 Level 3 Level 2 Level 1 Kids Password Rating Level ENTER RETURN

EXIT MOVE EXIT

Press the ENTER or button, and then select On using the buttons.
The Parental Control screen appears.
Select the desired Level you want using the buttons, then press the ENTER or button.
For example, if you select up to Level 6, discs that contain Level 7, 8 will not play. A higher number indicates that the program is intended for adult use only.
No Disc Timer Rec. Setup Password

Off On

English - 43

Page 44

Changing the Password
See page 94 if you forgot your password.
Select Change Password using the buttons.

No Disc Timer Rec. Setup Password Rating Level Change Password

: On : Level 1 Kids

The Enter the password message will be displayed.

Change Password

Enter the password
Enter the 4-digit password using the 0 to 9 buttons on the remote control.

* * * *

The Confirm the password message will be displayed.
Enter your password again using the 0 to 9 buttons on the remote control.
No Disc Timer Rec. Setup Confirm the password Change Password

44 - English

R135-XAA-ENG-45-55

9:57 AM

Page 45
This section shows various DVD recording methods.

Before Recording

This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference.

Recordable discs

This recorder can record on the following discs. DVD-RW DVD-R
DVD-RWs are rewritable. DVD-Rs are non-rewritable Compatibility between Samsung and Other Companies' Recorders
Disc Types Recording Recording Device Finalizing Additional Recording format in Samsung Recorder Samsung VR Mode DVD-RW V Mode Other Company Samsung DVD-R V Mode Other Company Other Company Samsung finalized not finalized finalized not finalized finalized not finalized finalized not finalized finalized not finalized finalized not finalized Not recordable Recordable Not recordable Recordable Not recordable Recordable Not recordable Not recordable Not recordable Recordable Not recordable Not recordable
Before Recording.45 Recording the current TV program you are watching.47
Recording from External Equipment.49
Copying from a Camcorder.50 Making a One Touch Recording (OTR).51 Setting a Timer Recording.51 Flexible Recording (for Timer Recording only).53 Editing the Scheduled Record List.53 Deleting the Scheduled Record List.54 Recording the Scheduled Record List.55
Finalize - This closes the DVD-R/-RW and no additional recording can be done. Unfinalize - This allows additional recording on a DVD-RW disc originally recorded on the DVD-R135. - A DVD-RW disc that has been recorded by DAO(Disc At once) in a PC cannot be unfinalized. - A DVD-RW disc that has been recorded in Video Mode of another manufacturer's recorder cannot be unfinalized. - A DVD-R disc cannot be unfinalized.

! # $ % ^ & DVD-RW(VR) Disc Name Total Title Total Playlist Recordable Time Protection Screen JAN SUN Disc Info Disc 1 None 01: 12 XP Not Protected CH 11 [Mono] 12:00 AM * @
! Disc Type @ Current information display status # Disc Name $ Total Title : Total number of titles % Total Playlist : Total number of Playlists ^ Recordable Time : The longest continuous recording time in each of the record modes(approximate) & Date : Current date * Time : Current time

English - 47

Page 48
Press the CH ( / ) or number ( ~ ) buttons to select the current program you want to record. Press the REC MODE button repeatedly, (or press the REC MODE button and then press the button) to select the recording speed(quality). SP LP EP XP

To stop recording

Press the STOP ( ) button to stop or finish a recording in progress. When using DVD-RW/DVD-R discs, the message Updating the information of disc. Please wait for a moment. is displayed.

To pause recording

Press the PLAY/PAUSE ( recording in progress. Press the PLAY/PAUSE ( recording. ) button to pause ) button again to resume

XP (01:11)

You can not change the record mode and the channel during recording. Recording will stop automatically if there is no free space left for recording. Up to 99 titles can be recorded onto a disc. Recording will stop automatically if a copy protected image is selected. If you are using a Cable Box(no antenna), you cannot watch a different cable TV program from the one you're recording. DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit.

Press the REC button.

Information concerning the channel is displayed on the screen and then recording begins. Icon( ) is displayed on the front panel.

Recording : CH10 [Mono]

To view the current status of the disc and progress of recording : Press the INFO button, and the information about the disc will appear.
DVD-RW(VR) Disc Name Total Title Total Playlist Recordable Time Protection Screen JAN SUN Disc Info Disc 7 None 01: 11 XP Not Protected Recording : CH 10 [Mono] 12:00 AM
Press the INFO button once again to view information about the recording.

Wait until LOAD disappears from the front panel display. If an unused DVD-RW disc is inserted, whether to initialize or not will be asked first. (See page 46)
Press the REC MODE button repeatedly (or press the REC MODE button and then press the button) to select the recording speed(quality). SP LP EP XP

Record Mode XP (01:11)

Press the INPUT SEL. button to select DV. If the input is set to DV, a playback/record menu that enables Digital camcorder control appears on the top of the screen.
The DV device is connected MOVE SELECT RETURN

50 - English

Page 51
Making a One Touch Recording (OTR)
Press the INFO button once again. Then you can check the information about the title being recorded
DVD-RW(VR) Name Recording Info JAN/01/2006 12:00 AM CH 10 Recording Title 7 Created Time JAN/01/2006 12:00 AM Recording Time 00:00:41 12:00 AM JAN SUN
You can set the DVD Recorder to record in preset increments by pressing the REC button repeatedly.
To stop recording Press the STOP ( ) button. The message Press STOP button once more to cancel Timer Record. is displayed.
If you want to record a TV channel, use the CH( / ) buttons or number buttons to select a desired channel. If you want to record from a connected external component, press the INPUT SEL. button to select an appropriate external input(AV1, AV 2 or DV).
CATV channels: 1 to 125 TV channels: 2 to 69 Example 1) Selecting Channel 120 + + Example 2) Selecting Channel 9 +
Press STOP button once more to cancel Timer Record.

Press the STOP (

) button again to stop recording.
Press the REC button to start recording.
Press the REC button to adjust the recording time. 0:30 1:00 1:30 2:00 3:00 4:00 off
Setting a Timer Recording
You need to set the Clock (Setup Clock Set) before proceeding with a timer recording. (See page 31)
The timer counter decreases to 0:00, then the DVD Recorder stops recording. After finishing recording, the DVD Recorder will be turned off automatically.
To view the current status of the disc and the progress of recording : Press the INFO button, and information about the disc will appear.
Wait until LOAD disappears from the front panel display. If an unused DVD-RW disc is inserted, whether to initialize or not will be asked first. (See page 46.)
Press the MENU button in Stop mode.
You can also set a timer recording via the TIMER button.

English - 51

Page 52
Press the buttons to select Timer Rec., and then press the ENTER or button.
DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Timer Record Scheduled Record List

Start/End Time: Start and end time of the timer recording Mode (Record mode) XP : Approx. 1 hour SP : Approx. 2 hours LP : Approx. 4 hours EP : Approx. 6 hours or 8 hours. FR : See page 53.
Press the buttons to select Timer Record, and then press the ENTER or button.
The Timer Record Input items are displayed.
DVD-RW(VR) No. Source Date

Source CH 11 Date 01/01

When you are recording at EP mode on a DVD-RW(V)/-R disc, it may not record the full 6 or 8 hours because the unit uses the VBR(Variable Bit Rate) ENCODING system. For example, if you record a Program with a lot of action, it uses a higher bit rate which in turn consumes more disc memory.
Scheduled Record List Current Time 12:03 AM Start
No. 01 Start 12:03 AM End 02:03 AM Mode

Press the ENTER button.

DVD-RW(VR) No. Source Date Start

05:00 AM :

Mode Edit
Scheduled Record List Current Time 12:03 AM End

07:00 AM :

Recordable Time : 01:59 SP

01/ 01 /

Recordable Time : 01:59 SP MOVE ENTER RETURN EXIT Recordable Time : 01:59 SP
Fill in the items using the buttons. : Moves to the previous/next item, 0~9 : Sets a value.
Source: Select the video input source (AV 1, AV 2) or the broadcasting channel you want to make a timer recording of. When selecting channels to be recorded, the buttons on the remote control can let you select only the channels that have been memorized during Auto Channel Memory. For the selection of other channels, use the number buttons. Date: Date that the timer recording starts - There are three options when setting the date. see below:
! To make a recording on a specific date, press the
( ) and Timer Set will appear on the front panel display. This means that a timer recording is set. Recording is automatically performed when the set time is reached.
or number buttons until the date you want appears.
No. 01 Source CH 11 Date Start End 02:03 AM Mode SP

01/01 12:03 AM

@ To make a recording at the same time every day
If the timer settings overlap The programs are recorded in order of priority. If timer recording is set for the first program and then again for the second program and both programs overlap, the following message will appear on the screen: This setting is identical with 1. The message shows that the first program has priority. After recording of the first program is complete, the second program starts being recorded. To exit without saving the current setting Press the MENU or TIMER button. To return to the previous menu Press the RETURN button if you don't want to set a timer recording.
(Mon-Fri), press the buttons until Mon-Fri appears:

Scheduled Record List Current Time 12:08 AM Start No. 01 No. 01

Start 05:00 AM

End 07:00 AM

Mode SP

Do you want to delete No.01? Yes No
DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Timer Record Scheduled Record list
Press the buttons to select Yes, and then press the ENTER button.
The selected entry will be deleted from the list.
Press the MENU button after the operation is finished. The menu screen will disappear.
You can not delete programs that are currently being recorded.

54 - English

Page 55
Recording the Scheduled Record List
When the start time in the Scheduled Record List is reached while the unit is powered off, the unit will automatically power on and start recording.
When the scheduled recording is operating, the program being recorded will not display on TV.
Power on TV using the TV remote control. Power off TV using the TV remote control if you dont want to see the program being recorded.
If a copy protection signal is received during recording, recording will stop.
If there is no free disc space or the disc is not recordable, recording will not operate. (You can record after replacing the disc.)

English - 55

R135-XAA-ENG-56-72

9:58 AM

Page 56

Before Playing

Read the following information before playing a disc. This section introduces basic playback functions and playback by disc type.
Region code (DVD-Video only)
Both the DVD recorder and the discs are coded by region. These regional codes must match in order for the disc to play. If the codes do not match, the disc will not play. The Region Number for this recorder is described on the rear panel of the recorder.
Disc types that can be played
Disc Types DVD-VIDEO Disc Logo Recorded content Disc Shape Max. Playing Time or minute Single sided(5) 240 VIDEO Double sided(5) 480 AUDIO Single sided(3.5) 80 Double sided(3.5) 160 Single sided(5) 74 AUDIO Single sided(3.5) 20 Single sided(5) JPEG Images Single sided(3.5) Single sided(5) MP3 Audio Single sided(3.5) Single sided(5) MPEG4 Movie Single sided(3.5) 1hr (XP: Excellent Quality) Single sided(5) 2hrs (SP: Standard Quality) (4.7GB) 4hrs (LP: Long Playback) VIDEO 6 or 8hrs(EP:Extended) AUDIO 2hrs (XP: Excellent Quality) Double sided(5) 4hrs (SP: Standard Quality) (9.4GB) 8hrs (LP: Long Playback) 12 or 16hrs (EP:Extended) 1hr (XP: Excellent Quality) VIDEO 5 (4.7GB) 2hrs (SP: Standard Quality) AUDIO 4hrs (LP: Long Playback) 6 or 8hrs (EP:Extended) 1 (XP: Excellent Quality) VIDEO 5 (4.7GB) 2hrs (SP: Standard Quality) 4hrs (LP: Long Playback) AUDIO 6 or 8hrs(EP:Extended)
AUDIO-CD JPEG CD-R/-RW MP3 CD-R/-RW MPEG4 CD-R/-RW

DVD-RAM

D I G I TA L

Dolby Digital

DIGITAL OUT

Digital Audio

English - 57

Page 58
Using the Disc Menu & Title Menu
Some discs contain a dedicated menu system that allow you to select special functions for the title, such as chapters, audio track, subtitles, film previews, information on characters, etc.
Using the Search Functions

For DVD-VIDEO discs

Press the DISC MENU button to enter the disc's menu.
Searching through a Chapter or Track
Move to the setup menu related to the playback operation. You can select the audio language and the subtitles provided by the disc.
Press the TITLE MENU button to move to the title menu of the disc.
Use this button if the disc contains more than one title. Some
During playback, press the SEARCH( on the remote control.
Fast 1(X 2) Fast 3(X 8) Fast 5(X 32) Fast 1(X 2)

) button

type of discs may not support the title menu function.
DVD-VIDEO/ DVD-RAM/ DVD-RW/DVD-R
Fast 2(X 4) Fast 4(X16) Fast 6(X128)

For DVD-RAM/-RW/-R discs

MPEG4 AUDIO CD (CDDA)
Fast 1 Fast 2 Fast 3 Fast X 2 Fast X 4 Fast X 8 Fast X 2
Press the TITLE LIST button to move to the Title List.
You can scan the program in reverse. To return to normal speed playback, press the PLAY( ) button. When you press and hold the SEARCH( ) button, playback is done at the default speed of fast 2. If you release the SEARCH( ) button, playback is performed at a normal speed.(Except CD-DA) The speed marked in this function may be different from the actual playback speed.
Title List : The Title List is simply a list of titles on a disc. If a title is deleted, that title cannot be played again. Playlist (DVD-RAM/-RW(VR)) : A playlist is a custom-made list of titles. When one playlist is played, only the titles within the playlist will play and then stop. Even if that playlist is deleted, the original recording will not be deleted.
No sound is heard during Scan(Search) mode except fast playback (1.7X speed) mode. For CD(CD-DA), You can hear sound during Scan mode.

58 - English

Page 59
Searching Chapters or Tracks
During playback, you can search quickly through a chapter or track.

About ANYKEY

During playback, press the SKIP( ) button on the remote control. If you press the SKIP( ) button, it moves to the beginning of the chapter or track or marker(DVDRW(VR mode)). Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker(DVD-RW(VR mode)). If you press the SKIP( ) button, it moves to the next chapter or title or marker(DVD-RW(VR mode)).
The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, track, and time. You can also change the subtitle and audio settings and set some features including Repeat, Angle, and Zoom.

Slow Motion Play

Moving to a scene directly using the ANYKEY
If you want to move to a title or chapter to find a desired scene.
In Pause mode, press the SEARCH ( the remote control. ) button,

) button on

If you press the SEARCH( Slow 1(1/2)

Slow 2(1/4) ) button,

Slow 3(1/8)
Press the ANYKEY button during playback.

Slow 2(1/4)

DVD-VIDEO
1/2 1/20 00:00:00 Off ENG Off 1/3 Off D 2CH
To return to normal speed playback, press the PLAY( ) button.
Chapter Time Subtitle Audio Repeat
Press and hold the SEARCH( ) button during pause, and the disc will play slowly at a 1/2 speed. If the button is released, the pause operation will resume.

Angle Zoom

CHANGE
The speed marked in this function may be different from the actual playback speed. Slow motion operates only in the forward direction on MPEG 4 discs.
Press the buttons to select the Title or Chapter.

Step Motion Play

Chapter Time Subtitle Audio Repeat Angle Zoom
Press the STEP( ) button on the remote control in the still mode.
Each time the button is pressed, a new frame will appear. When STEP( ) is pressed, the previous frame will be activated. When STEP( ) is pressed, the next frame will be activated. To return to normal speed playback, press the PLAY(

) button.

Press the buttons or number (0~9) buttons to select the desired scene and then press the ENTER button.

Disc Protection allows you to protect your discs from being formatted or deleted due to unintended operations
DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Disc Name :
Disc Protection : Protected Disc Format : DVD-VR Disc Finalize Delete All Title Lists

Formatting a Disc

Use these instructions to format a disc. The disc protection should be cleared.
Press the buttons to select Disc Manager, and then press the ENTER or button.
DVD-RW(VR) Title List Playlist Title List
Disc Manager Timer Rec. Setup
DVD-RW(VR) Title List Playlist Disc Name : Disc Protection : Not Protected Disc Format : DVD-VR Disc Finalize Delete All Title Lists
Press the buttons to select Disc Protection, then press the ENTER or button.
Press the buttons to select Disc Format, and then press the ENTER or button.
DVD-RW(VR) Title List Disc Name : Disc Protection : Not Protected Disc Format : DVD-VR Disc Finalize Delete All Title Lists
Press the buttons to select Protected, then press the ENTER button.
DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Disc Name : Disc Protection : Not Protected
Protected Disc Format : DVD-VR Disc Finalize Delete All Title Lists

English - 87

Page 88
DVD-RW You will be prompted with the confirmation message Choose the recording format for DVD- RW
Disc Manager DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Disc Name : Disc Protection : Not Protected Disc Format : DVD-VR Disc Finalize Delete All Title Lists
Press the buttons to select desired mode, then press the ENTER button.
You will be prompted again with the message All data will be deleted. Do you want to continue?
DVD-RW(VR) Title List Playlist Disc Manager Timer Rec. Setup Disc Name : Disc Protection : Not Protected All Format DVD-VR Disc data will :be deleted. Do you want to continue? Disc Finalize Delete All Title Lists Yes No
Press the buttons to select Delete All Title Lists, and then press the ENTER or button.
You will be prompted with the confirmation message Do you want to delete all title lists?.

The disc is formatted.

DVD-VR and DVD-V are defined according to their recording format. DVD-VR DISC DVD-RW DVD-V DVD-RW DVD-R
Do Disc Format : DVD-VR Disc Manager you want to delete all title lists? Disc Finalize Timer Rec. Delete All Title Lists Yes No Setup

Deleting All Title Lists

The disc protection should be cleared first.
When Protected Entry exists: The Delete All Title List function will not operate. If you want to delete a protected entry, disable Protection for it on the Lock item. (See page 73)
All title lists are deleted.

88 - English

2 - English

Page 3

Precaution

Important Safety Instructions
Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) Read these instructions. 2) Keep these instructions. 3) Heed all warnings. 4) Follow all instructions. 5) Do not use this apparatus near water. 6) Clean only with dry cloth. 7) Do not block any ventilation openings, Install in accordance with the manufacturer's instructions. 8) Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. 9) Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A groundingtype plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. if the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet. 10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus. 11) Only use attachments/accessories specified by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as a power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
Be careful not to put your hand into the disc tray. Do not place anything other than the disc in the disc tray. Exterior interference such as lightning and static electricity can affect normal operation of this recorder. If this occurs, turn the recorder off and on again with the POWER button, or disconnect and then reconnect the AC power cord to the AC power outlet. The recorder will operate normally. Be sure to remove the disc and turn off the recorder after use. Disconnect the AC power cord from the AC outlet when you dont intend to use the recorder for long periods of time. Clean the disc by wiping in a straight line from the inside to the outside of the disc.

Protection

This DVD Recorder can allow you to protect the contents of your discs, as described below. Program-protection : See page 75 Locking a Title Disc-protection : See page 87 Disc Protection DVD-RAM/DVD-RW/DVD-R discs that are incompatible with the DVD-VIDEO format cannot be played with this product. For more information on DVD recording compatibility, consult your DVD-RW/DVD-R manufacturer. If poor quality DVD-RW/DVD-R discs are used, your recordings may fail.
Do not use the following discs!
LD, CD-G, CD-I, CD-ROM and DVD-ROM discs should not be used in this product. [Note] Disc types that can be played : CD/CD-R/CD-RW/MP3/JPEG/DVD-Video/DVDRAM/DVD-RW/ DVD-R. DVD+R/+RW cannot record, but the finalized +R/+RW can be played. For a DVD-R/DVD-RW disc, which has been recorded in Video Mode on another component, it can play only when finalized. Some commercial discs and DVD discs purchased outside your region may not be playable with this product. When these discs are played, either No disc." or "The disc
cannot be played. Please check the regional code of the disc." will be displayed. If your DVD-RAM/DVD-RW/-R disc is an illegal copy or is

DVD-RAM Disc Playback

DVD-RAM discs come with or without a cartridge. For this product, we recommend DVD-RAM discs that come without cartridges. You cannot play a DVD-RAM in most DVD players due to compatibility issues. Only DVD-RAM standard Version 2.0. discs can be played in this unit. For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.
not in DVD video format, it may also not be playable.

Disc compatibility

High Speed Recording discs can be used in this unit. Not all brands of discs will be compatible with this unit. The latest firmware upgrade to improve recording & playback quality can be downloaded from our web site. (Download Center at www.samsung.com) If disc compatibility problems continue, or there is an issue upgrading your recorder, contact the Call Center at 1-800-SAMSUNG.

English - 5

Page 6

One-Touch A function that can be operated button by using only one button. ANYKEY A function that can be operated button by using ANYKEY button.
About the use of this Instruction Manual
1) Be sure to be familiar with Safety Instructions before using this product. (See pages 2~3) 2) If a problem occurs, check the Troubleshooting. (See pages 91~94)
You can only use either the VR or Video mode on a DVD-RW, but not both at the same time. You can change the DVD-RW format to another format by reinitializing. It should be noted that the disc's data will be lost when changing formats.

Copyright

2006 Samsung Electronics Co. All rights reserved; No part or whole of this users manual may be reproduced or copied without the prior written permission of Samsung Electronics Co.

English - 9

9:54 AM

Page 10

Step 3

Step 6

Finalizing & Playing on other DVD components
There are two different recording methods, Direct Recording and Timer Recording. Timer recording is classified as a Date : Once(mm/dd), MON-FRI, Every SAT, etc. as a record mode : XP (high quality mode), SP (standard quality mode), LP (long recording mode), and EP (extended mode) according to the record mode. When recording is set in the FR mode, the best quality picture is recorded with regards to the remaining time on the disc.
To play your DVD on other DVD components, finalizing may be necessary. First, finish all editing and recording operations, then finalize the disc.
When using a DVD-RW disc in VR Mode
Although finalizing is generally unnecessary when playing the disc on a VR Mode compatible component, a finalized disc should be used for playback.
When using a DVD-RW disc in Video Mode
The disc should be finalized first to enable playback on anything other than this recorder. No more editing or recording can be made on the disc once it has been finalized.

Step 4

Playing

When using a DVD-R disc

You should finalize the disc to play it on a component other than this recorder. You cannot edit or record on the disc once it has been finalized.
You can select the title you want to play in a displayed menu and then immediately start playback. A DVD consists of sections called titles, and sub sections called chapters. During recording, a title is created between two points where you start and stop recording. Chapters will be created automatically when you finalize recording on DVD-R / DVD-RW discs in Video mode. The chapters length (interval between chapters) varies according to the record mode.

14 - English

Page 15
Step 1: Connecting the Antenna Cable
There are several ways to connect your DVD Recorder. Select one of the Antenna connections on the following pages.
Antenna + DVD Recorder + TV : No Cable box
You can record non-scrambled channels by selecting the channel on the DVD Recorder. Also use this method if you watch channels without cable box.
The VHF/UHF ANT (RF) OUT jack of this product sends only signals received through the antenna. It does not output Audio/Video signals. You must connect Audio/Video cables to view Video from the unit. (i.e. DVD playback)

English - 15

Page 16
Antenna + Cable box + DVD Recorder + TV : Cable box with many scrambled channels
You can record channels by selecting the channel on the cable box. You cannot record one channel while watching another channel. Be sure that the cable box is turned on.

16 - English

Page 17
Antenna + DVD Recorder + Cable box + TV : Cable box with a few scrambled channels
You can record non-scrambled channels by selecting the channel on the DVD Recorder. You cannot record scrambled channels that require a cable box.

English - 17

Page 18
There are several ways to connect your DVD Recorder. Select one of the video connections on the following pages. You must use one of the following audio/video connections on this unit.
Connecting to a Video input jack
Connect a video(yellow) cable between the VIDEO(yellow) OUT jack on DVD Recorder and VIDEO(yellow) IN jack on the TV (or AV amplifier).
You will enjoy normal quality images. Connect audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on your TV(or AV amplifier). (See pages 21 ~ 23)

18 - English

Page 19
Connecting to an S-Video input jack
Connect an S-Video cable(not supplied) between the S-VIDEO OUT jack on DVD Recorder and S-VIDEO IN jack on your TV (or AV amplifier).
You will enjoy high quality images. S-Video separates the picture element into black and white (Y) and color (C) signals to present clearer images than regular video input mode. Connect audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV(or AV amplifier). (See pages 21 ~ 23)
S-Video or Component video outputs are available only if your TV supports S-Video input or Component video input, respectively. If S-Video or Component video output does not work, check the TV connections and the TV input selection settings.

English - 19

Page 20
Connecting to Component video input jacks (Y,PB,PR)
1. Connect Component video cables(not supplied) between the COMPONENT OUT(Y,PB,PR) jacks on DVD Recorder and COMPONENT IN(Y,PB,PR) jacks on your TV (or AV amplifier). 2. If the connected TV supports Progressive Scan, press the P.SCAN button on the front of the DVD Recorder to enjoy best quality video. Pressing the P.SCAN button switches Progressive (480p) / Interlace (480i) scan mode in turn. You will enjoy best quality accurate color reproduction images. Component video separates the picture element into black and white(Y), blue(PB), red(PR) signals to present clear and clean images. Connect audio cables(white and red) between the AUDIO OUT jacks on the DVD Recorder and AUDIO IN jacks on TV(or AV amplifier). (See pages 21 ~ 23)

Press the RETURN or button to return to the previous menu. Press the MENU button to exit the menu. IRE: Short for the Institute of Radio Engineers. An IRE unit is a relative unit of measure equaling 1/140th of the peak-topeak (p-p) video amplitude.

42 - English

Page 43
The first time the Parental Control is accessed, the Create the Password message will be displayed.
Create a 4-digit password using the 0 to 9 buttons on the remote control.
No Disc Timer Rec. Setup Create the password Parental Control

Setting the Rating Level

Select Rating Level using the buttons.
No Disc Timer Rec. Setup Password Rating Level Change Password : On : Level 1 Kids
EXIT MOVE ENTER RETURN EXIT
The Re-enter Password screen appears to confirm the password. Enter your password again.
No Disc Timer Rec. Setup Confirm the password Parental Control
Press the ENTER or button.

No Disc Timer Rec. Setup

Level 8 Adults : On Level 7 : Level 1 Kids Level 6 Change Password Level 5 Level 4 Level 3 Level 2 Level 1 Kids Password Rating Level ENTER RETURN

EXIT MOVE EXIT

Press the ENTER or button, and then select On using the buttons.
The Parental Control screen appears.
Select the desired Level you want using the buttons, then press the ENTER or button.
For example, if you select up to Level 6, discs that contain Level 7, 8 will not play. A higher number indicates that the program is intended for adult use only.
No Disc Timer Rec. Setup Password

Off On

English - 43

Page 44

Changing the Password
See page 94 if you forgot your password.
Select Change Password using the buttons.
No Disc Timer Rec. Setup Password Rating Level Change Password

: On : Level 1 Kids

The Enter the password message will be displayed.

Change Password

Enter the password
Enter the 4-digit password using the 0 to 9 buttons on the remote control.

* * * *

The Confirm the password message will be displayed.
Enter your password again using the 0 to 9 buttons on the remote control.
No Disc Timer Rec. Setup Confirm the password Change Password

44 - English

R135-XAA-ENG-45-55

9:57 AM

Page 45
This section shows various DVD recording methods.

Before Recording

This unit can record on various types of discs. Before recording, read the following instructions and select the disc type according to your preference.

Recordable discs

This recorder can record on the following discs. DVD-RW DVD-R
DVD-RWs are rewritable. DVD-Rs are non-rewritable Compatibility between Samsung and Other Companies' Recorders

Select the PLAY ( ) icon on the upper part of the screen to playback the camcorder and find the starting position to copy.
To start recording, select REC( G ) icon in the top side of the screen using the buttons, then press the ENTER button.
To stop recording Before you start
Check that the disc has enough available space for the recording. Adjust the record mode. See pages 27~28 to see how to connect the camcorder to your DVD recorder. Press the STOP ( ) button to stop or finish recording in progress. When using DVD-RW/DVD-R discs, the message Updating the information of disc. Please wait for a moment is displayed.
Press the OPEN/CLOSE button, and place a recordable disc on the disc tray.
You can not change the record mode and input source while recording. Recording will stop automatically if there is no free space left for recording. Up to 99 titles can be recorded onto a disc. DVD-RW discs must be formatted before starting to record. Most new discs are sold unformatted. Do not use DVD-R authoring discs with this unit. To access on-screen controls during recording, press the or buttons. When copying from a camcorder and the end of the tape is reached (no Video), the screen may turn blue or purple.
Wait until LOAD disappears from the front panel display. If an unused DVD-RW disc is inserted, whether to initialize or not will be asked first. (See page 46)
Press the REC MODE button repeatedly (or press the REC MODE button and then press the button) to select the recording speed(quality). SP LP EP XP

Record Mode XP (01:11)

Press the INPUT SEL. button to select DV. If the input is set to DV, a playback/record menu that enables Digital camcorder control appears on the top of the screen.
The DV device is connected MOVE SELECT RETURN

50 - English

Page 51
Making a One Touch Recording (OTR)
Press the INFO button once again. Then you can check the information about the title being recorded
DVD-RW(VR) Name Recording Info JAN/01/2006 12:00 AM CH 10 Recording Title 7 Created Time JAN/01/2006 12:00 AM Recording Time 00:00:41 12:00 AM JAN SUN
You can set the DVD Recorder to record in preset increments by pressing the REC button repeatedly.
To stop recording Press the STOP ( ) button. The message Press STOP button once more to cancel Timer Record. is displayed.
If you want to record a TV channel, use the CH( / ) buttons or number buttons to select a desired channel. If you want to record from a connected external component, press the INPUT SEL. button to select an appropriate external input(AV1, AV 2 or DV).
CATV channels: 1 to 125 TV channels: 2 to 69 Example 1) Selecting Channel 120 + + Example 2) Selecting Channel 9 +

Title List : The Title List is simply a list of titles on a disc. If a title is deleted, that title cannot be played again. Playlist (DVD-RAM/-RW(VR)) : A playlist is a custom-made list of titles. When one playlist is played, only the titles within the playlist will play and then stop. Even if that playlist is deleted, the original recording will not be deleted.
No sound is heard during Scan(Search) mode except fast playback (1.7X speed) mode. For CD(CD-DA), You can hear sound during Scan mode.

58 - English

Page 59
Searching Chapters or Tracks
During playback, you can search quickly through a chapter or track.

About ANYKEY

During playback, press the SKIP( ) button on the remote control. If you press the SKIP( ) button, it moves to the beginning of the chapter or track or marker(DVDRW(VR mode)). Pressing the button once again within 3 seconds returns to the beginning of the previous chapter or track or marker(DVD-RW(VR mode)). If you press the SKIP( ) button, it moves to the next chapter or title or marker(DVD-RW(VR mode)).
The ANYKEY function allows you to easily search for a desired scene by accessing title, chapter, track, and time. You can also change the subtitle and audio settings and set some features including Repeat, Angle, and Zoom.

Slow Motion Play

Moving to a scene directly using the ANYKEY
If you want to move to a title or chapter to find a desired scene.
In Pause mode, press the SEARCH ( the remote control. ) button,

) button on

If you press the SEARCH( Slow 1(1/2)

Slow 2(1/4) ) button,

Slow 3(1/8)
Press the ANYKEY button during playback.

Slow 2(1/4)

DVD-VIDEO
1/2 1/20 00:00:00 Off ENG Off 1/3 Off D 2CH
To return to normal speed playback, press the PLAY( ) button.
Chapter Time Subtitle Audio Repeat
Press and hold the SEARCH( ) button during pause, and the disc will play slowly at a 1/2 speed. If the button is released, the pause operation will resume.

Angle Zoom

CHANGE
The speed marked in this function may be different from the actual playback speed. Slow motion operates only in the forward direction on MPEG 4 discs.
Press the buttons to select the Title or Chapter.

Step Motion Play

Chapter Time Subtitle Audio Repeat Angle Zoom
Press the STEP( ) button on the remote control in the still mode.
Each time the button is pressed, a new frame will appear. When STEP( ) is pressed, the previous frame will be activated. When STEP( ) is pressed, the next frame will be activated. To return to normal speed playback, press the PLAY(

When a DVD-VIDEO contains multiple angles of a particular scene, you can select the Angle function. This is only available during playback. If the disc contains multiple angles, the ANGLE mark appears on the screen.

Zooming-In

Using the ANGLE button
Press the ANYKEY button during playback or pause.
Press the ANGLE button during playback.
MOVE 0~9 NUMBER Angle 1/3
Press the ANGLE button or buttons to select the desired angle.
Press the buttons to select Zoom, and then press the ENTER button. ( ) will be displayed.
Press the buttons to move to the area you want to enlarge.
Press the ENTER button. The screen will be enlarged to twice the normal size.
If you press the ENTER button once again after the screen is enlarged to twice the normal size, the screen size will be enlarged to four times the normal size.
Press the buttons to select Angle and press the buttons or number(0~9) buttons to select the desired angle.

Off 2X 4X 2X Off

1/2 1/20 00:00:11 Off ENG Off 1/3 Off D 2CH

English - 63

Page 64

Using Bookmarks

This feature lets you bookmark sections of a DVD-Video, DVD-RAM or DVD-R/-RW(V mode), so you can quickly find them.
Playing Back a the Audio language Selecting Bookmark
Bookmarking with a DVD-Video/DVD-RAM/DVD-RW(Video mode)/DVD-R disc
Press the MARKER button during playback.

(V mode)

Press the buttons to select a bookmarked scene.

Bookmark

- - - - - - - --

- - - - - - - - - --

CANCEL
Press the MARKER button during playback.Press the ENTER button when the desired scene appears.
The number 1 is displayed and the scene is memorized.

1 - - - - - - - - --

Press the ENTER or PLAY( ) button to start playing from the selected scene.

Clearing a Bookmark

MOVE PLAY CANCEL RETURN
Press the MARKER button during playback
Press the button to move to the next position.

- - - --

Press the ENTER button when the desired scene appears.
The number 2 is displayed and the scene is memorized.
Press the CANCEL button to delete the selected bookmark.

- 6 - - - --

Repeat above to bookmark other positions. You can bookmark up to 10 scenes.
When the disc tray is opened and then closed, bookmarks will disappear. The button display may differ depending on the disc type.

64 - English

Page 65
Using Markers Marking with a DVD-RW(VR mode) disc

Playing Back a Marker

Marker
-- -- -- -- -- -- -- -N:2
-- -- -- -- -- -- -- -- -- --
The number 01 is displayed and the scene is memorized.
01 -- -- -- -- -- -- -- -- -N:1

Page 69

To Program Tracks
You can register a maximum of 30 tracks in the playlist.

Playing a Picture Disc

Press the ANYKEY button during playback, then select Play option using buttons.
TRACK 1 No. Title 001 TRACK 1 PLAY MODE 002 TRACK 2 Repeat : Off 003 TRACK 3 Play option : Normal TRACK 005 TRACK TRACK TRACK 7 MOVE ENTER Music List 01/15 Length 00:03:50 00:04:00 00:03:49 00:03:47 00:04:29 00:03:44 00:03:44 EXIT
Insert an JPEG disc into the disc tray.
JPEG Disc Navigation Timer Rec. Setup Disc Navigation

0:00:01 TRACK 1

Select Playlist using the buttons, and then press the ENTER button.
The Playlist screen will appear.
Select tracks in the order in which you want them to play using the buttons. Press the ENTER button.
CDDA CDDA CDDA CDDA CDDA CDDA CDDA CDDA
Press the buttons to select Disc Navigation, and then press the ENTER or button.

Playlist 07/15

TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5 TRACK 6 TRACK 7 TRACK 004 TRACK 1 TRACK 3 TRACK 4 TRACK 7
Press the buttons to select Photo, and then press the ENTER or button.
If you playlisted a wrong track, press the button, then press the buttons to select wrong track and press the CANCEL button.
The wrong track will be removed.
Press the buttons to select a picture.
JPEG JPEG01 Photo List 01/08

Playlist 03/03

TRACK 1 TRACK 2 TRACK 3 TRACK 4 TRACK 5 TRACK 6 TRACK 7 TRACK 8

JPEG04 JPEG05 JPEG06

TRACK 1 TRACK 3 TRACK 4
ROOT JPEG01 JPEG02 JPEG03

JPEG07

Slide Show MOVE ENTER CANCEL EXIT
To see the next 8 pictures, press the SKIP(

) button. ) button.

To see the previous 8 pictures, press the SKIP(

Press the PLAY(

) button to playback the playlist.

English - 69

9:59 AM

Page 70

-1 If you press the PLAY( screen will appear.

) button, the Slide show

Playing an MPEG4 Disc
The picture interval (Slide show speed) must be set.

DVD-RW(VR)

Slide Show Speed Slow Normal Fast
MPEG4 File is used to contain the audio and video data. MPEG4 File with following extensions can be played. -.AVI,.DIVX,.avi,.divx

JPEG01 MOVE PHOTO ENTER

Insert a MPEG4 Disc into the disc tray.
CD Disc Navigation Disc Navigation
-2 Press the ENTER button with a picture selected in the Album screen. Select a display mode (Album screen ( ), Slide show ( ), Rotation ( ) or Zoom ( )) using the buttons, then press the ENTER button.
Programme Photo Music Setup

Drama APR/19/2006 SP MOVE
Press the buttons to select an entry you want to protect from the Title List, and then press the ENTER or button.
Sports(A1) No. Title Drama Music Title List 5/6 Length Edit 00:00:21 00:00:03 Play
00:00:15 Rename 00:00:16 Delete 00:06:32 Edit 00:08:16 Protection EXIT
Press the buttons to select Protection, and then press the ENTER or button.
Sports(A1) No. Title Drama Music Length 00:00:21 00:00:03 Play Title List 5/6 Edit
Press the buttons to select an entry you want to delete from the Title List, and then press the ENTER or button.

Title List 5/6

Sports(A1) Title Protection: APR/21/2006 SP Sports(A1) APR/21/2006 SP MOVE ENTER RETURN EXIT On Off MOVE

English - 75

Page 76
Deleting a Section of a Title
Follow these instructions to delete a section of a Title List entry.
You will be prompted with the confirmation message. DVD-RW(VR mode): Since Playlist is present, the message Do you want to delete?(Related playlists may be deleted.) is displayed.
Sports(A1) Title List 5/6
Press the TITLE LIST button. The Title List screen is displayed.
Do you want to delete? (Related playlists may be deleted.) Sports(A1) APR/21/2006 SP MOVE ENTER RETURN EXIT Yes No
Drama No. Title Drama Music
Title List 1/6 Length 00:00:21 00:00:03 00:00:15 00:00:16 00:06:32 00:08:16 Edit

Drama APR/21/2006 SP

DVD-RW(Video mode), DVD-R: Since Playlist is not present, the message Do you want to delete? is displayed. The message may be different depending on the type of disc.
Press the buttons to select an entry you want to edit from the Title List, and then press the ENTER or button.
Title List 5/6 No. Title Drama Music Length 00:00:21 00:00:03 Play Edit
Press the buttons to select Yes, and then press the ENTER button
You cannot delete a protected entry. If you want to delete a protected entry, select Off in the Title Protection menu. Once an entry is deleted from the Title List, it cannot be recovered. Once a DVD-R or DVD-RW is finalized, it cannot be deleted. With DVD-R, titles are only deleted from the menu, however, the Title remains physically on the disc.
DVD-RW(VR) Edit Title List
Title List No. 05 Start End

00:00:00

00:00:00 00:00:00

Delete ENTER RETURN

Return EXIT

76 - English

Page 77
Press the ENTER button at the starting point.
The image and starting point time are displayed on the section deletion starting point window.
Press the buttons to select Delete, and then press the ENTER button.
The message Do you want to delete?(Deleted part will not be restored) is displayed.
Title List No. 05 Start End Title List No. 05 Start End 00:00:05
00:00:00 00:00:05 00:00:05

00:10:15 00:10:15

A new Scene will be added to the current Playlist. A new Make Scene screen is displayed. Repeat the above steps to create further scenes.

Playlist

Press the buttons to select New Playlist, and then press the ENTER or button.
The Make Scene screen is displayed.
If you want to make a new playlist, go to MENU new playlist. You can check and see all the scenes on Edit Playlist screen.
To return to Edit Playlist menu

Title List 1/6

Press the buttons to select Return, and then press the ENTER button.
The Edit Playlist screen is displayed.
APR/23/2006 Edit Playlist 1/5 No. Title 12:00 12:30 12:00 12:30 12:00 LengthEdit 00:00:21 00:00:03 00:00:15 00:00:16 00:06:32
Press the ENTER button at the start point.
DVD-RW(VR) Scene No. 001 Start End MOVE ENTER Make Scene APR/23/2006 12:00 AM 1 Scene APR/23/2006 12:00 AM
01 APR/23/APR/23/APR/24/APR/24/APR/25/2006

00:00:00 00:00:10

You can create up to 99 playlist entries. Depending on the disc type, the displayed screen may look slightly different. Press the MENU or PLAY LIST button after the operation has finished. The Edit Playlist screen will disappear.
The image and starting point time are displayed on the Start window.

78 - English

10:1 AM

Page 79

Playing Entries in the Playlist
Follow these instructions to play the playlist entries.
Press the buttons to select Play, and then select the ENTER button.
The playlist entries will be played.
APR/24/2006 No. Title Edit Playlist 3/5 Length Edit 12:00 00:00:21 12:30Play 00:00:03 12:00Rename 00:00:15 12:30Edit Scene 00:00:16 12:00Copy 00:06:32 Delete RETURN EXIT
With the unit in stop mode, press the PLAY LIST button.
APR/23/2006 No. Title 12:00 12:30 12:00 12:30 12:00 Edit Playlist 1/5 Length Edit 00:00:21 00:00:03 00:00:15 00:00:16 00:00:32
APR/24/2006 12:00 AM 1 Scene APR/24/2006 12:00 AM MOVE ENTER
APR/23/2006 12:00 AM 1 Scene APR/23/2006 12:00 AM MOVE ENTER
Press the MENU button in the stop mode. Press the buttons to select Playlist, and then press the ENTER or button. Press the buttons to select Edit Playlist, and then press the ENTER or button.
To view the current status of the disc and the progress of playback : Press the INFO button, and the information about the disc will appear.
DVD-RW(VR) Disc Name Disc Info
Playlist Total Title Total Playlist Recordable Time Protection Screen JAN SUN 01: 09 XP Not Protected Playback[Playlist] 12:00 AM
Press the buttons to select the title you want to edit from the Playlist, and then press the ENTER or button.
The Edit Playlist menu is displayed : Play, Rename, Edit Scene, Copy, Delete.
Press the INFO button once again. Then you can check the information about the playlist currently being played back.
DVD-RW(VR) Name Playlist Created Time Length Playing Time Total scene JAN SUN Playing Info APR 12:00 AM CH11 3/5 APR 12:00 AM 00: 01: 36 XP 00: 00: 12:00 AM

The screen returns to the Edit Playlist screen when the playback has finished.
Press the STOP( ) button to stop playing. The screen returns to the Edit Playlist screen.

English - 79

Page 80
Renaming a Playlist Entry
Follow these instructions to rename a playlist entry, i.e. to edit the title of a playlist entry.
Enter the desired characters using the buttons.
DVD-RW(VR) Dolphin Rename
This function is the same as the Rename function in renaming the title list. (See page 74.) The maximum number of characters that can be entered is 31. All 31 characters can be displayed by pressing the INFO button.
The changed title name is displayed on the title item of the selected playlist entry.
Dolphin No. Title Edit Playlist 3/5 Length Edit 12:00 00:00:21 12:30 00:00:03 00:00:15 12:30 00:00:16 12:00 00:00:32
APR/24/2006 No. Title Edit Playlist 3/5 Length Edit 12:00 00:00:21 12:30 00:00:03 Play 12:00 00:00:15 Rename 12:30 00:00:16 Edit Scene 12:00 00:00:32 Copy Delete
Dolphin 1 Scene APR/24/2006 12:00 AM MOVE ENTER
01 APR/23/APR/23/Dolphin 04 APR/24/APR/25/2006
Press the buttons to select Rename, and then press the ENTER button.
APR/24/2006 No. Title Edit Playlist 3/5 Length Edit Play 12:00 00:00:21 Rename 12:30 00:00:03 Edit Scene 12:00 00:00:15 Copy 12:30 00:00:16 Delete 12:00 00:00:32

80 - English

Page 81
Editing a Scene for the Playlist
Follow these instructions to edit scenes for a playlist
DVD-Recorder DVD-RW(VR) Scene No. 1/7
Edit Scene Playlist No. Play Modify 3

01 00:00:26

02 00:00:07

03 00:00:04

Move Add

04 00:00:03 MOVE

05 00:00:11 ENTER

06 00:00:04 RETURN

Delete EXIT
Science No. Science 7 Scene APR/24/2006 10:43 AM MOVE ENTER RETURN EXIT Title Science Sky Dolphin Natural Edit Playlist 1/4 Length Edit 00:00:17 00:00:06 00:00:06 00:00:37

Playing a Selected Scene

Press the buttons to select the scene you want to play, and then press the ENTER button.
The playlist entry to be played is selected.
DVD-Recorder DVD-RW(VR) Scene No. 2/7 Edit Scene Playlist No. Play Modify 01 00:00:00:00:00:00:04 Move Add 04 00:00:03 MOVE 05 00:00:11 ENTER 06 00:00:04 RETURN Delete EXIT 3
The Edit Playlist menu is displayed:Play, Rename, Edit Scene, Copy, Delete.

Dolphin No. 03 04

Dolphin 7 Scene
The selected scene is played.
Edit Playlist 3/4 Title Science Sky Dolphin Natural Length Edit Play 00:00:17 Rename 00:00:06 Edit Scene 00:00:06 Copy 00:00:37 Delete
APR/24/2006 10:43 AM MOVE ENTER RETURN EXIT
To stop scene play, press the STOP(
Press the buttons to select Edit Scene, and then press the ENTER button.
The Edit Scene screen is displayed.

English - 81

Additional Information 96 - English

Page 97

Specifications
Power requirements Power consumption Weight
120V AC, 60Hz 19 Watts 5.5 lb 16.9 in(W) x 8.5 in(D) x 1.9 in(H) +41F to +95F Keep level when operating. Less than 75% operating humidity 1.0 V p-p at 75 load, sync negative

General

Dimensions Operating temp. Other conditions Video (1,2) S-Video input (Y: 1.0Vp-p, C: 0.286Vp-p at 75 load) Audio(1,2) Max.Audio Input Level : 2Vrms IEEE 1394(4p) compatible jack Regular TV broadcasting: VHF (2~13), UHF (14~69) Cable TV broadcasting: 1~125 Analog output jacks 1, 2 Audio Optical/Coaxial digital audio output Full scale Analog output level : 2Vrms
DV Input Receivable Channels

Output

Video output jack 1 Video S-Video output 1 (Y:1.0Vp-p, C:0.286Vp-p at 75 load) Component output 1 (Y: 1.0Vp-p, Pb: 0.70Vp-p, Pr: 0.70Vp-p at 75 load) HDMI/DVI output 1 (480p, 720p, 1080i) Picture Compression format Audio Compression format MPEG-II Dolby Digital 2ch/256kbps XP (about 8 Mbps), SP (about 4 Mbps), LP (about 2 Mbps), EP (about 1.2 Mbps or about 0.8 Mbps) Audio Frequency Response 20 Hz ~ 20 kHz

Recording Quality

Audio Output

Disc Type

For DVD discs, audio signals recorded at 96kHz sampling frequency are converted and output at 48kHz. DVD 48 / 96kHz 48kHz AUDIO CD(CDDA) 44.1kHz 44.1kHz
Analog Audio Output Digital Audio Output

English - 97

Page 98

Warranty

LIMITED WARRANTY TO ORIGINAL PURCHASER
This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC. (SAMSUNG) and delivered new, in the original carton to the original consumer purchaser, is warranted by SAMSUNG against manufacturing defects in materials and workmanship for the following limited warranty period:
One (1) Year Parts / Ninety Days (90) Labor
This limited warranty begins on the original date of purchase, and is valid only on products purchased and used in the United States, and does not include transportation, installation, removal or reinstallation. Warranty repairs must be performed by SAMSUNGs authorized service center. To receive warranty service, the original dated bill of sale must be presented upon request as proof of purchase to SAMSUNG or SAMSUNGs authorized service center. Transportation to and from the service center is the responsibility of the purchaser. SAMSUNG will repair or replace this product, at our option and at no charge with new or reconditioned parts, if found to be defective during the limited warranty period specified above. The product must be returned during the warranty period with transportation charges prepaid to SAMSUNGs designated service center. Prior to returning any product for warranty service, the purchaser must contact SAMSUNG for problem determination and service procedures. SAMSUNG does not warrant uninterrupted or error-free operation of the product. All replaced parts and products become the property of SAMSUNG and must be returned to SAMSUNG. Replacement parts and products assume the remaining original warranty, or ninety (90) days, whichever is longer. This limited warranty covers manufacturing defects in materials and workmanship encountered in normal, noncommercial use of this product and shall not apply to the following, including, but not limited to: damage which occurs in shipment; applications and uses for which this product was not intended; failures or problems which are caused by products or equipment not supplied by SAMSUNG; accidents, misuse, abuse, neglect, misapplication, fire, water, lightning or other acts of nature; incorrect electrical line voltage, fluctuations or surges; damage caused by improper or faulty installation; improper connection with any peripheral; product alteration or modification; improper or unauthorized repair; cosmetic damage or exterior finish; product with altered serial numbers; failure to follow operating instructions, customer adjustments, maintenance and environmental instructions that are covered and prescribed in the instruction book; use of non-SAMSUNG or unauthorized parts, supplies, accessories or equipment which damage this product or result in service problems; failures or problems due to incompatibility with other equipment.