Read these operating instructions carefully before using the unit. Follow all the safety instructions listed below. Keep these operating instructions handy for future reference. 1) 2) 3) 4) 5) 6) 7) 8) 9) Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat. Do not defeat the safety purpose of the polarized or grounding- type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet. LINE THROUGH WRITING
10) Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, the point where they exit from the apparatus. 11) Only use attachments/accessories specied by the manufacturer. 12) Use only with the cart, stand, tripod, bracket, or table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over. 13) Unplug this apparatus during lightning storms or when unused for long periods of time. 14) Refer all servicing to qualied service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling Cautions

Before connecting other components to this HDD & DVD Recorder, be sure to turn them all off. Do not move the HDD & DVD Recorder while a disc is being played, or the disc may be scratched or broken, the HDD & DVD Recorder internal parts may be damaged. Do not put a ower vase lled with water or any small metal objects on the HDD & DVD Recorder. Be careful not to put your hand into the disc tray. Do not place anything other than the disc in the disc tray. Exterior interference such as lightning and static electricity can affect normal operation of this HDD & DVD Recorder. If this occurs, turn the HDD & DVD Recorder off and on again with the STANDBY/ON button, or disconnect and then reconnect the AC power cord to the AC power outlet. The HDD & DVD Recorder will operate normally. Be sure to remove the disc and turn off the HDD & DVD Recorder after use. Disconnect the AC power cord from the AC outlet when you dont intend to use the HDD & DVD Recorder for long periods of time. Clean the disc by wiping in a straight line from the inside to the outside of the disc. Apparatus shall not be exposed to dripping or splashing and no objects lled with liquids, such as vases, shall be placed on the apparatus. The Mains plug is used as a disconnect device and shall stay readily operable at any time.

DVD-RW Disc Playback and Recording
Recording and playback can be performed on DVD-RW discs in both the Video and VR Modes. Once a DVD-RW recorded in both the Video and VR Modes is nalised, you cannot perform additional recording. Once a DVD-RW recorded in Video Mode is nalised, it becomes DVD-Video. In both modes, playback can be performed before and after nalisation, but additional recording, deleting and editing can not be performed after nalisation.

English _5

If you want to record the disc in VR Mode and then record in V Mode, be sure to execute Format. Be careful when executing Format because all the recorded data may be lost. A DVD-RW blank disc is initialised to VR Mode when rst initialised.
DVD+RW Disc Playback and Recording
With DVD+RW discs, there is no difference between DVD-Video format(Video mode) and DVD-Video Recording format(VR mode). Finalising is generally unnecessary when using a DVD+RW disc.
DVD-RAM Disc Playback and Recording
Ensure that the recording mode is set to VR mode. Otherwise, this product will not be able to play the recording. You cannot play a DVD-RAM in most DVD components due to compatibility issues. Only DVD-RAM standard Version 2.0. discs can be played in this unit. DVD-RAM recorded on this unit may not work with other DVD components. To determine compatibility with these DVD-RAM discs, refer to the users manual for the player. For cartridge type DVD-RAM discs, remove the cartridge and use the disc only.

Disc Copy

Title Copy Specications Contents Recorded Video Title Copy Protected Title Copy Once Title HDD DVD DVD HDD
Supported Not supported Move (Deletes the Title in the HDD after copying)
Supported Not supported Not supported
Once Copy Once programme has been recorded on the DVD disc, this title cannot be copied to HDD anymore. But Copy Once programme has been recorded on the HDD, this title can be copied to DVD-RW (VR mode) with CPRM or DVD-RAM. Contents Copy Specications Contents MP3 JPEG(photo) DivX CD-DA HDD DVD or USB Supported Supported Supported Not supported DVD HDD or USB Supported Supported Supported Supported USB HDD or DVD Supported Supported Supported Not supported

Among MP3 players in the list above, those that do not use Mass Storage Class are not supported.

English _9

LINE THROUGH WRITING
CONNECTING & SETTING UP
Warning Precaution General Features Before reading the users manual How to use the HDD & DVD Recorder Unpacking Description Tour of the Remote Control Connecting the HDD & DVD Recorder Additional connections Other TYPES of connections with the Video Output Cable Other TYPES of connections with the Audio Output Cable Connecting HDMI/DVI to a TV Connecting to AV IN 3, DV input jack Connecting to USB Devices

SYSTEM SETUP

On-Screen Menu Navigation Plug & PLAY Setup Clock Set Channel Set Setting up the System Options Setting up the Language Options Setting up the Audio Options Setting up the Video Options component output (progressive scan) HDMI Resolution Setting up the Parental Lock Setting up the Recording Options

DTV FUNCTIONS

Basic Functions Guide

10_ Line through writing

PLAYBACK
Region code (DVD-Video only) Logos of Discs that can be played Disc types that can be played Playing a Disc Using the Disc Menu & Title Menu Using the playback related buttons Using the INFO button Selecting the Subtitle Language Selecting the Soundtracks & Audio Channels Changing the Camera Angle Repeat Play Zooming-In Using Markers Using the Bookmarks Playing an Audio CD/MP3 Music/Photo Simultaneous Playback Viewing a Picture Playing a DivX Recordable Discs Recording Formats Recording Mode Unrecordable pictures Recording immediately Copying from a Camcorder Making a One Touch Recording (OTR) Simultaneous Recording and Playback Time Shift function as a live signal Making a Timer Recording Go To Recorded List Basic Editing (Title List) Using the Sort function (Title List) Navigation Menu Select Contents Advanced Editing (Playlist) COPYING FROM HDD TO DVD OR VICEVERSA Copying MP3, JPEG or DivX Changing the name of Music/Photo/DivX le Disc Manager

RECORDING

EDITING

REFERENCE

104 Troubleshooting

APPENDIX

106 Specications 107 Warranty

English _11

GENERAL FEATURES
This unit allows you to record and playback high quality digital video on DVD-RAM/RW/R discs or on the HDD. You can also edit digital images on DVD-RAM/RW discs or HDD. HDD Recording DVD-SH893M You can record up to Approx. 264 hours of video (in EP 8 Hr mode) on the internal 160 GB (gigabyte) hard disk (HDD). DVD-SH895M You can record up to Approx. 421 hours of video (in EP 8 Hr mode) on the internal 250 GB (gigabyte) hard disk (HDD). DVD-SH897M You can record up to Approx. 534 hours of video (in EP 8Hr mode) on the internal 320 GB (gigabyte) hard disk (HDD). With both recordable DVD and a high-capacity HDD in the same recorder, you have the exibility to keep recordings on the HDD for quick access anytime, or record to DVD for archiving or playing on other DVD players. (See pages 69~72) Copy between HDD and DVD You can copy recordings from the HDD to recordable DVD, or from recordable DVD to the HDD. You can only copy in the same record mode as source title. (See page 95) Simultaneous Recording and Playback Playback and recording for both the DVD and the built-in hard disk drive (HDD) are completely independent. For instance, While Recording to the HDD, play another title on the HDD or play a previously recorded programme on DVD. While Recording to a DVD, play a previously recorded programme on HDD. (See pages 76~77) Automated Quality Adjustment for Timer Recording If FR mode is selected, the video quality is adjusted automatically so that all video for the scheduled time can be recorded onto the free disc space. (See pages 79~81) Copying data from a digital camcorder using a DV input jack Record DV Device video onto HDD and DVD-RAM/RW/R discs using the DV input jack (IEEE 1394-4pin/4pin). (See page 75) High quality progressive scan Progressive scanning provides high resolution and icker free video. The 10-bit 54-MHz DAC and 2D Y/C Separating Circuitry provides the highest image playback and recording quality. (See page 44) DivX Certication DivX is a digital video format created by DivX, Inc. This is an ofcial DivX Certied or DivX Ultra Certied device that plays DivX video. HDMI (High Denition Multimedia Interface) HDMI reduces picture noise by allowing a pure digital video/audio signal path from the HDD & DVD Recorder to your TV. This HDD & DVD Recorder supports 576p, 720p and 1080i, 1080p. Anynet+(HDMI CEC) Anynet+ is a function that can be used to operate the recorder using a Samsung TV remote control, by connecting the HDD & DVD Recorder to a SAMSUNG TV using an HDMI Cable. (This is only available with SAMSUNG TVs that support Anynet+.) (See Page 38) EZ Record Mode This function enables you to initialise and Finalise a disc automatically. (See page 48)

14_ Line through writing

Step 4 : Playing
You can select the title you want to play in a displayed menu and then immediately start playback. A DVD consists of sections, called titles, and sub- sections, called chapters.
Step 5 : Editing a recorded disc
Editing on discs is easier than conventional video tapes. The HDD & DVD Recorder supports many different edit functions, possible only with DVDs and HDD. With a simple and easy edit menu, you can operate various edit functions, such as delete, copy, rename, lock, etc., on a recorded title. Creating a playlist (DVD-RAM/-RW in VR mode, HDD) With this HDD & DVD Recorder, you can create a new playlist on a disc and edit it without the original, preexisting recording. LINE THROUGH WRITING
Step 6 : Finalising & Playing on other DVD components
To play your DVD on other DVD components, nalising may be necessary. First, nish all editing and recording operations, then nalise the disc. When using a DVD-RW disc in VR Mode DVD discs recorded in VR mode can only be played back in DVD recorders, not players. When using a DVD-RW disc in Video Mode The disc should be nalised rst to enable playback on anything other than this HDD & DVD Recorder. No more editing or recording can be made on the disc once it has been nalised. To enable recording on the disc again, the disc must be unnalised. When using a DVDR disc You should nalise the disc to play it on a component other than this HDD & DVD Recorder. You cannot edit or record on the disc once it has been nalised.
You can nalise the disc automatically using EZ Record function. (See page 48)

English _15

UNPACKING

Accessories

Check for the supplied accessories below.

Video/Audio Cable

RF Cable for TV

Remote Control

Batteries for Remote Control (AAA Size)

Instruction Manual

Quick Guide
Preparing the Remote Control
Install Batteries in the Remote Control Open the battery cover on the back of the remote control. Insert two AAA batteries. Make sure that the polarities (+ and ) are aligned correctly. Replace the battery cover. If the remote does not operate properly : Check the polarity +/ of the batteries (Dry-Cell) Check if the batteries are drained. Check if remote sensor is blocked by obstacles. Check if there is any uorescent lighting nearby.

ATV PR 3 CH 004 --072 Name ----------

Progress

Please wait. Now setting the clock. If you want to exit clock setting, press the [MENU] button.

Clock Set

mo. JAN Tuesday da. 01 yr. 2009 hr. 12 min. Auto 00 On

34_ System setup

CLOCK SET
1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the OK or button. 3. Press the buttons to select Clock Set, then press the OK or button.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE System Clock Set Language Audio Video Parental Lock Recording sSELECT rRETURN eEXIT 1

SYSTEM SETUP

Time Zone
To setup, follow steps 1~3. 4. Press the buttons to select Time Zone, then press the OK or button. Select the time zone of your area using the buttons, then select OK using button.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Time Zone Time Zone Manual Clock Set GMT + Daylight Saving00:00 OK
GMT (Greenwich Mean Time) Table
Country United Kingdom, Portugal GMT GMT+00:00 City Dublin, Edinburgh, London, Lisbon, Casablanca Berlin, Stockholm, Rome, Vienna, Paris, Madrid, Prague, Warsaw, Brussels, Copenhagen, Oslo, Bern, Budapest, Warsaw, Prague Athens, Helsinki, Istanbul, Cairo, Pretoria, Israel
France, Austria, Belgium, Demark, Germany, Netherlands, Italy, Norway, Spain, Sweden, Switzerland, GMT+01:00 Hungary, Czech Republic Finland, Turkey, Greece, Eastern Europe GMT+02:00

Manual clock set

To setup, follow steps 1~3. 4. Press the buttons to select Manual Clock Set, then press the OK or button. Use the buttons to input Time, Date or Year. Use number buttons to input clock data directly. 5. Press the OK button, then the date and time will be saved. If you dont press the OK button, it will not be saved.

HDD Library Guide

mo. da.

hr. min. Auto

Channel
Timer Record Disc Manager Setup < MOVE

Tuesday

sSELECT

rRETURN

You must have the RF cable connected to set the Auto Clock. (See page 22) The DVD Recorder automatically sets the clock according to the time signal broadcast between the channels PR1 to

HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Channel List (Digital) Favourite List (Digital) Auto Scanning Manual Scanning (Digital) Manual Setup (Analogue)
Manual Scanning (Digital) Country Channel type Scan Mode Channel Number Frequency Bandwidth Signal status 50%

: : : : : :

United Kingdom Digital All CH 5 177500kHz 8MHz

Cancel

Manual Setup (Analogue)
To setup, follow steps 1~2 on page 36. 3. Press the buttons to select Manual Setup (Analogue), then press OK or button. 4. Press the buttons to select a PR(programme) you wish to edit, delete, or swap, then press the COLOUR button. Select Edit, Delete or Swap. Edit- RED(A) button : You can add or edit programme (PR) information. After you have changed the PR information (CH, Name, MFT), select Save, then press the OK button. - CH : Tune the channel using buttons. - Name : Display station name automatically detected in broadcasting signal. If not detected, you can edit name by using buttons. - MFT (Manual Frequency Tunning) : You can tune the channel frequency manually using buttons. Delete GREEN(B) button : The selected programme will be removed. Swap YELLOW(C) button : You can swap the channel information of two programmes (PR). For example, if you wish to swap PR2 and PR5, select swap at PR2, then press the OK button at PR5.

CH ---------------

Name ---------------------C

Delete

Manual Setup (Analogue) PR CH Name MFT 01

m MOVE sSELECT

English _37

Channel List (Digital)

This function is possible in DVB-T mode only. This function is used to edit the favourite channel list or delete the channel. To setup, follow steps 1~2 on page 36. 3. Press the buttons to select Channel List (Digital), then press OK or button. 4. To delete a channel from the Channel List (Digital), press the RED(A) button. Press the OK button to watch that channel.

DTV channel list

001 BBC ONE 002 BBC TWO 007 BBC THREE 030 CBBC Channel 040 BBC NEWS BBCi Remove
Press OK button in the DVB-T view to display the Channel List

(Digital).

#/$ Page

r Return

You can select RADIO mode by pressing the TV/RADIO button on the
remote control. This button is used to toggle between the TV and RADIO modes.

Radio channel list

If a new channel is added or a lesser number of channels are received
than the TV channels, run Auto Scanning again.

Favourite List (Digital)

This function is possible in DVB-T mode only. You can immediately register the present channel to the Digital Favourite Channel list. To setup, follow steps 1~2 on page 36. 3. Press the buttons to select Favourite List (Digital), then press OK or button. 4. To add the current channel the Digital Favourite channels, press the YELLOW(C) button. To delete a favourite channel from the Digital Favourite channel list, press the RED(A) button. Press the OK button to watch that channel.

Favourite List(Digital)

001 BBC THREE 002 BBC NEWS 24

Remove

Add Current

38_ System setup

SETTING UP THE SYSTEM OPTIONS
This function allows you to setup the system setting. 1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the OK or button. 3. Press the buttons to select System, then press the OK or button. 4. Press the buttons to select the desired system option, then press the OK or button. 5. Press the buttons to select the desired item, then press the OK or button.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Auto Power Off Power Save DVB-T Auto Subtitle Touch Key Sound DivX(R) Registration : Off : Off : On : Off

System

Anynet+ (HDMI CEC) : Off

Auto Power Off Setting

This feature automatically turns off your HDD & DVD Recorder, if you do not press any button for the selected time. 1. Press the buttons to select Auto Power Off, then press the OK or button.
Library Auto Power Off : Off Off 2. Press the buttons to select the desired item, then press the 2:Hours Power Save Off Guide OK or button. Anynet+ (HDMI CEC) 6:Hours Off Channel DVB-T Auto Subtitle : On Off : Auto power off is disabled. Timer Record Touch Key Sound : Off DivX(R) Registration Disc Manager 2 Hours : HDD & DVD Recorder will automatically turn off for Setup 2 hours after the last button is pressed. m MOVE sSELECT rRETURN eEXIT 6 Hours : HDD & DVD Recorder will automatically turn off for 6 hours after the last button is pressed. If the turn off time set with the Auto Power off function is reached during playback or recording, the device will operate until the playback or recording is nished.

3D Noise Reduction Off : Off

English _43

Video Output
You can enjoy high quality image through RGB or Component video connections. RGB video output is available connecting scart jack (AV1) and component video output is available connecting component (Y, PB, PR) jack. Only one of these signals can be selected at one time. Component RGB
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT TV Aspect 3D Noise Reduction Video Output Component output BD Wise HDMI Resolution : 4:3 Letter Box : Off : Component Component RGB : Interlace : On : 576p
In Component mode, you can set video output to Progressive or Interlace, see page 44. When the HDMI cable (not supplied) is not connected, available video output jacks are as follow.
Available Video Output Jack
Setting mode Output jack Component Output (Y, PB, PR) AV1 Scart Composite Video out R, G, B Composite Component mode O X O O RGB MODE X O X O
When the HDMI cable(not supplied) is connected, RGB output does not operate. Video output is set to Component.
COMPONENT OUTPUT (PROGRESSIVE SCAN)
This function is available when video output is component. This setting enables you to select a desired progressive mode. To view Progressive scan mode, rst connect the component cable. (See page 27) Be sure the Component cables are connected properly. Progressive The message "Do you want to maintain progressive mode? Reverting in 10 seconds." will be displayed. Select "Yes" to revert progressive mode. Interlace The message "Do you want to maintain interlace mode? Reverting in 10 seconds." will be displayed. Select "Yes" to revert interlace mode.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT TV Aspect 3D Noise Reduction Video Output Component output BD Wise HDMI Resolution : 4:3 Letter Box : Off : Component : Interlace Interlace Progressive : On : 576p
When the HDMI cable (not supplied) is connected, this screen is not displayed.

44_ System setup

BD Wise (Only Samsung products)
BD Wise is Samsungs latest inter-connectivity feature. When you connect Samsung products with BD-Wise to each other via HDMI, the optimum resolution will be set automatically. On : The original resolution of the DVD disc will be output to the TV directly. Off : The output resolution will be xed according to the Resolution previously set, regardless of the resolution of the disc.

HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT TV Aspect 3D Noise Reduction Video Output Component output BD Wise HDMI Resolution : 4:3 Letter Box : Off : Component : Interlace : On Off On576p :
If you want to change the resolution in BD Wise, you must set BD Wise to Off in advance. If you set off the BD Wise, the resolution of the connected TV will be adjusted to its maximum resolution automatically. If the HDD & DVD Recorder is connected to a device that does not support BD Wise, you can not use BD Wise function. For a proper operation of BD Wise, set each BD Wise menu of the player and the TV to On respectively.

HDMI RESOLUTION

This setting is used when the unit is connected by HDMI with Display devices (TV, projector, etc). BD Wise : BD Wise : Automatically selects the optimal resolution according to the TV that supports BD Wise. (The BD Wise menu item appears only if BD Wise is set to On.) 576p 720 x 576 720p : 1280 x 720 1080i : 1920 x 1080 1080p : 1920 x 1080
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT TV Aspect 3D Noise Reduction Video Output Component output BD Wise HDMI Resolution : 4:3 Letter Box : Off : Component BD Wise 576p : Interlace 720p : On 1080i : 576p 1080p rRETURN

Output selection

Connect the HDD & DVD Recorder to your TV via HDMI. Set your TVs input to HDMI.
The BD Wise menu item appears only if BD Wise is set to On.
BD wise function is enabled only if BD Wise-compliant Samsung Products are connected with each other using the HDMI cable.
Progressive scan automatically activates when HDMI is connected. Consult your TV Users Manual to nd out if your TV supports Progressive Scan. If Progressive Scan is supported,
follow the TV Users Manual regarding Progressive Scan settings in the TVs menu system.
If Video Output is set incorrectly, the screen may be blocked. The resolutions available for HDMI output depend on the connected TV or projector. For details, see the users
manual of your TV or projector.
When the resolution is changed it may take a few seconds for a normal image to appear.

English _45

SETTING UP THE PARENTAL LOCK
The Parental Lock function works in conjunction with DVDs and DVB-T that have been assigned a rating which helps you control the types of DVDs that your family watches. There are up to 8 rating levels on a disc.

HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Programe Grade DVD Level Change Password : Off : Off

46_ System setup

SETTING UP THE RECORDING OPTIONS
Automatic Chapter Creator

(V-mode)

A DVD-Video consists of Titles and Chapters. When you record one programme, it makes one Title. If you use this function, the Title will be divided into Chapters. 1. With the unit in Stop mode, press the MENU button. Recording HDD & DVD RECORDER 2. Press the buttons to select Setup, then press the OK or HDD button. Library Chapter Creator : On Off On6 Hours EP Mode Time : 3. Press the buttons to select Recording, then press the OK Guide EZ Record : Off or button. Channel V-Mode Compatibility : Off Timer Record 4. Press the buttons to select Chapter Creator, then press Disc Manager the OK or button. Setup 5. Press the buttons to select Off or On, then press the OK or m MOVE sSELECT rRETURN eEXIT button. Off : Select if you do not want to use Automatic Chapter Creator. On : Select this option to use the Automatic Chapter Creator feature. Press the EXIT button to exit the menu.
6. Press the REC button to start recording. (See page 71 about how to set recording speed) The message Do you want to create the chapter menu after this recording? is displayed. 7. Press the buttons to select OK, then press the OK button. A new chapter is created according to the selected recording mode. A chapter will be about 5 minutes long in XP and SP, and about 15 minutes long in LP and EP mode. 8. Press the STOP button to stop recording. 9. To display the created titles, nalise the disc (See page 102) and then press the TITLE MENU button. The title menu will be displayed. Finalising is generally unnecessary when using a DVD+RW disc. 10.To display the created chapters, select the desired Title and then press the DISC MENU button. The chapter menu for the selected Title will be displayed.
The Automatic Chapter Creator function does not work during Timer Recording or when you turn the power off.

EP Mode Time Setting

You can select one of four recording modes by pressing the REC MODE button repeatedly. In EP(Extended Play) mode, you can set recording time to 6 or 8 hours with this setting.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Chapter Creator EP Mode Time EZ Record : On 6 Hours 6:Hours Off 8:Hours

Recording

V-Mode Compatibility : Off

English _47

EZ Record
This function enables you to initialise and Finalise a disc automatically. 1. Press the buttons to select EZ Record, then press the OK or button. 2. Press the buttons to select On, then press the OK or button. Press the EXIT button to exit the menu. 3. Insert a disc. If the disc is new, It is initialised to V mode automatically. (DVD-RW only) 4. Press the REC button. 5. EZ Record function will automatically Finalise the disc under the following conditions. When you press the OPEN/CLOSE button on your HDD & DVD Recorder after recording on at least 70% of the disc. The tray will open after the disc has been nalised. The above feature is available only when a DVD-RW(V), DVD+R or DVD-R disc is inserted.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Chapter Creator EP Mode Time EZ Record : On : 6 Hours : Off Off
V-Mode Compatibility OnOff :
If you insert a new DVD-RW disc, It is initialised to V mode automatically. If you insert a new DVD+RW disc, it will be formatted automatically. If you select off, you must initialise (see page 70) and nalise the disc manually in the Disc Manager menu. (see

page 102)

The length of Recording is different according to recording mode. (see page 71)

V-Mode Compatibility

This feature is about the setup for selecting audio when recording the Dual STEREO (Multi-audio) broadcasting on HDD. It does not directly affect DVD recording of a programme. Off : Both Dual L and Dual R of the multi-audio broadcasting are recorded on HDD. Titles recorded on HDD under such setup status cannot be copied to DVD+RW/R or DVD-RW (V mode). On : Either Dual L or Dual R of the multi-audio broadcasting is recorded on HDD. Titles recorded on HDD under such setup status can be copied to DVD+RW/R or DVD-RW (V mode) Dual L and Dual R options can be selected from Audio Selection.
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN eEXIT Chapter Creator EP Mode Time EZ Record : On : 6 Hours : Off On
V-Mode Compatibility Off : Off
HDD Library Guide Channel Timer Record Disc Manager Setup m MOVE sSELECT rRETURN Chapter Creator EP Mode Time EZ Record Audio Selection : On : 6 Hours : Off : Off Dual L Dual R
V-Mode Compatibility : On

48_ System setup

DTV functions

BASIC FUNCTIONS

Display Screen
After the television channels have been stored, you will see the following picture(banner) each time you switch channels. DTV FUNCTIONS

12:00 TUE 1 JAN 2009 12:00 - 12:25 Blue Peter

TUE 1 JAN

001 BBC ONE 002 BBC TWO 007 BBC THREE 030 CBBC Channel 040 BBC NEWS BBCi A

DTV Guide

Blue Peter ---
--Neighbours The Weakest Link
BBC News Beg. Borrow or Steal

Look North

Strictly Come Dancing: It T
Basli Brush BBC News BBCi

Tracy Beake

Blue Peter BBC News BBCi

Out There ---

Timer Rec

#/$ PREVIOUS/NEXT DAY

INFORMATION
The contents of cell could be displayed slowly according to the broadcasting. If 'Daylight Saving Time' and 'GMT Time' settings are wrong, EPG Time will be incorrect.

50_ DTV functions

Guide Timer Recording
Make sure that clock must be set before operating this function. (see pages 35~36) 1. Press the buttons to select desired programme, then press RED(A) button. 2. Set timer recording option. Target Media: Select the media to record HDD or DVD. Series Recording: With the series recording function, you can easily and automatically record every episode of a series. Select 'On' if you want to use series recording function. The Series Recording option will be dimmed if the selected programme is not one of a series.

DTV FUNCTIONS

12:00 TUE 1 JAN 2009 12:00 - 12:25 Blue Peter Timer TUE 1 JAN Rec

--The Weakest Link

BBC News
You can check the setting in the scheduled List. (see pages 78~79) The title information is displayed in the Title List as for Guide REC. If Timer Rec is set, the icon is displayed in the set programme. Up to 12 recordings are possible including guide recording and

general recording.

Target Media

--Basli Brush

Blue Peter

Neighbours

HDD Off

Beg. Borrow or Steal

Series Recording Save

BBC News BBCi

--Tracy Beake

English _51

Playback
This section introduces basic functions of playback and playback by disc type. Read the following information before playing a disc.