Q3 Q4 Q5
HDD does not be recognized in BIOS setup. 1 First, confirm whether each cable was connected correctly. 2 Confirm whether Jumper-setting is correct. 3 Confirm whether BIOS setup became correctly. Even though the HDD recognized in BIOS setup, it does not be seen in Windows. 1 Confirm whether did correctly partition and format. 2 Partition can be created through the Fdisk or Installing OS according to OS's version. I am looking for a Software & Firmware (mainly about drivers) but I found nothing. Where I can find I want ? We don't release any firmwares. Because the product has been already optimized with its own configurations. IDE (PATA & SATA) drive does not need any drivers. You just have to make a partition and format your drive for using. Please make sure whether you had partitioned and formatted. First of all, you must partition and format for recognizing the new drive in the Windows Explorer. Within Win98 series, please use the Fdisk. Within Win2000 & Win-XP, please use the Disk Management. When installing Win2000 or Win-XP, the installation process includes the partitioning step itself. To open the Disk Management 1 Click Start, point to Settings, and then click Control Panel. 2 Double-click Administrative Tools, and then double-click Computer Management. 3 In the left panel, expand Storage, and then expand Disk Management.
Contact SAMSUNG WORLD WIDE
If you have any comments or questions regarding a Samsung products. Country CANADA U.S.A GERMANY U.K RUSSIA UKRAINE AUSTRALIA Customer Care Center 1-800-SAMSUNG (7267864) 1-800-SAMSUNG (7267864) 01805 - 121213 ( 0,14Min) 0870 SAMSUNG (7267864) 8-800-200-0400 8-800-502-Web Site www.samsung.com/ca www.samsung.com www.samsung.de www.samsung.com/uk www.samsung.ru www.samsung.com/ur www.samsung.com/au
" Hybrid Disk Drive products are licensed for use only on devices that deploy the Windows VISTA operating system as the principle operating system. If you or any other party install(s) an operating system on the computing device that is not Window Vista, the use of this Hybrid Disk Drive may require an additional license from Microsoft. For further information, please contact Microsoft. " SAMSUNG ELECTRONICS CO., LTD. STORAGE SYSTEM DIVISION HEAD OFFICE: 94-1, IM SOO-DONG, GUMI-CITY KYUNG BUK, KOREA 730-350 FAX : 82-54-479-5567 This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life. To prevent possible harm to the environment or human health from uncontrolled waste disposal, please separate this from other types of wastes and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract. This product should not be mixed with other commercial wastes for disposal.
2.5" HDD INSTALLATION GUIDE
Samsung does NOT guarantee any data on your drive, please always BACK-UP your precious data.

Precautions

1MB = 1,000,000bytes / 1GB = 1,000,000,000 bytes. Actual accessible capacity may vary from advertised capacity due to formatting and partitioning of the hard drive, as well as due to your computer's operating system. Do not drop, shock or strike. If apply impact to the HDD, it causes a Bad Sector by crashing between Head and Media. Do not stack. Do not external shock and vibration. Do not remove all items, such as Hard drive label, warranty label. Warranty void if any stickers or labels are removed or damaged. Never disassemble hard drives. Do not touch the circuit board with hands or tools. Protect the HDD from Electrostatic Discharge(ESD). MR Head is very sensitive in Electrostatic. Keep the HDD in their static shielding bag. Avoid extreme temperatures and humidity places. Humidity causes a drive malfunction by reacting with an ingredient of oil in Disk and Head surface. Also, parts can be corrode by leaving in humidity.

The Names and Content of Toxic and Hazardous Substances or Elements
Parts Printed Circuit Assemblies Head Disk Assemblies Toxic and hazardous substances or elements Cd Hg Cr 6+ PBB PBDE Pb O O O O O X O O O O O X
O : Indicates that the concentration of the hazardous substance in all h omogeneous materials in the parts is below the relevant threshold of the SJ/T11363-2006 standard. X : Indicates that the concentration of the hazardous substance of at least one of all homogeneous materials in the parts is above the relevant threshold of the SJ/T11363-2006 standard.
When use an external case

DO NOT DROP!

DO NOT PRESS!
Samsung Electronics Co., Ltd. Printed in Korea.

BF68-00237A REV02

Do not drop or fall while using and being storage the external case. An external case is easy to transfer, but can be shocked easily also. Check the External case's Grounding External case's Grounding prevents HDD malfunction form ESD
PATA Installation Configuring your Hard Disk Drive (Master, Slave)
SATA Installation Installing the hard disk
Note: SATA 1.5Gb/s Speed Limit Jumper setting Only for SATA 3.0Gb/s products. In some rare cases SATA 1.5Gb/s hosts can not establish SATA interface connection with SATA 3.0Gb/s devices due to interface protocol issues. In this case the jumper may be installed as shown on the figure below to force the device to negotiate for SATA 1.5Gb/s speed.

Polarity

Jumpers
(a) Turn off the power of your computer. (b) Unplug the external power cables to the computer. (c) Open the cover of your Computer. Cover opening mechanism and the location of the hard disk drive may vary from one computer to another. (Consult your computer manual) (d) Insert the HDD into an available 3.5" bay in your computer and secure it to computer and secure it to the chassis using the provided screws. (e) Connect Cables.
Make the computer detect the hard disk. 1 If your computer supports IDE HDD Auto Detection, the hard disk drive will automatically be detected. 2 If your computer does not support auto detect, go into the User Define Mode and by referring written information on the product, set the correct settings for Cylinder, Head, and Sector and if some Bios must be, set the HDD Mode to LBA. 3 Save the changed details and exit.

Installing the hard disk

Master Slave Cable Select Power Connector SATA Interface Connector Jumper Pins (For Factory Use Only)
Attach the SATA interface cable to the interface connector on the hard disk drive. The connector is keyed and will fit in only one way. Attach the power cable to the power receptor on the hard disk drive. The connector is keyed and will fit in only one way. Check all other cable connections before turning on your computer. CAUTION! : Do not force or rock the connectors into their sockets on the hard disk drive. Push them in straight until they are seated.

2. Partitioning and Formatting the Drive
Refer to your Operating System manual or system manual for partitioning and formatting.
Installation Your Hard Drive
Note: - Turn off the system power ! - Cover opening mechanism and the location of the hard disk drive may vary from one computer to another.
3. Samsung World Wide Web Site
Additional information can be obtained at www.samsunghdd.com.
Do Not Connect In Reverse !!

Computer Main Board

Turn off the computer, unplug the external cables, and open computer cover. Mount the hard disk drive in the designated place in the computer with screws provided with the product. Connect 40 pin interface cable and power cable. Make sure that the direction of the cables are correct and matches the shape of the receptacles when connecting cables. Incorrect cable connection may damage the hard disk drive.

SATA Interface Cable

Power Cable
1. Making Computer Detect the New Device
Run the CMOS (BIOS) set-up program to detect the new hard disk drive.
When using within an USB external case, sometimes drive is not recognized. It may be caused by insufficiency of USB DC power. By supplying a subsidy DC power, the symptom can be solved. When using within an USB external case, drive can not be Format. First, confirm whether a partition has been created correctly. Format does not work if there is no partition.

Serial SATA Host Adapter

Go into CMOS screen during the booting of the computer. For descriptive details of the program, refer to the computer's user's manual

Mobile SATA

Spinpoint M6

Capacity Model 8 MB

HM320JI

HM251JI

FEATURES
Max. 160GB formatted capacity per disk SATA Native Command Queuing Feature TuMR/PMR head with FOD technology Serial ATA 1.5Gbps Interface Support Load/Unload Head Technology DRIVE CONFIGURATION Capacity Interface Buffer DRAM Size2 Byte per Sector Rotational Speed PERFORMANCE SPECIFICATIONS Average Seek time (typical) Average Latency Data Transfer Rate Media to/from Buffer (Max.) Buffer to/from Host (Max.) Drive Ready Time (typical)3 ATA Security Mode Feature Set ATA S.M.A.R.T. Feature Set SilentSeek NoiseGuard
250GB/320GB SATA 1.5Gbps 8 MB 512 5,400 RPM
12 ms 5.6 ms 826Mbits/s 150MB/s 4 sec
ENVIRONMENTAL SPECIFICATIONS Temperature Operating 5 ~ 55 Non-operating -40 ~ 70 Humidity (non-condensing) Operating 5 ~ 90 % Non-operating 5 ~ 95 % Linear Shock (1/2 sine pulse) Operating(2ms) 325 G Non-operating(1ms) 1000 G Vibration Operating(Random,10~500Hz) 0.73Grms Altitude (relative to sea level) Operating -300 to 3000 m Non-operating -400 to 15000 m
RELIABILITY SPECIFICATIONS Non-recoverable Read Error 1 sector in 1014 bits 600,000 Controlled Ramp Load/Unload ACOUSTICS Idle (typical) Performance Seek (typical) POWER REQUIREMENTS Voltage Spin-up Current (Max.) Seek (typical)4 Read/Write (typical) Low Power Idle (typical) Standby (typical) Sleep (typical)

2.4 Bel 2.6 Bel

PHYSICAL DIMENSION Height (Max.) Width Length Weight (avg.)
9.5 mm 69.85 mm 100 mm 102 g
* Note : Design and specifications are subject to change without prior notice.
+5V5% 900 mA 2.2 W 2.0 W 0.6 W 0.25 W 0.2 W
1.1MB = 1,000,000 Bytes, 1GB = 1,000,000,000 Bytes Accessible capacity may vary as some OS uses binary numbering system for reported capacity 2 Upper 128 KB is used for firmware 3 Power-On to Drive Ready 4 30% duty cycle, random seek 5 Power requirements based on enabled DIPM & 1.5Gbps speed
2.5" HDD product specification Rev 1.0 Match with product manual Rev 01