During thunderstorms, disconnect the AC main plug from the wall outlet. Voltage peaks due to lightning could damage the unit.
Do not expose the unit to direct sunlight or other heat sources. This could lead to overheating and malfunction of the unit.

Phones

Protect the player from moisture (i.e. vases) , and excess heat (e.g.fireplace) or equipment creating strong magnetic or electric fields (i.e.speakers.). Disconnect the power cable from the AC supply if the player malfunctions. Your player is not intended for industrial use. Use of this product is for personal use only. Condensation may occur if your player or disc has been stored in cold temperatures. If transporting the player during the winter, wait approximately 2 hours until the unit has reached room temperature before using.
The batteries used with this product contain chemicals that are harmful to the environment. Do not dispose of batteries in the general household trash.
This product is covered by one or more of the following U.S. patents:
5,060,220 6,771,891 7,142,493 7,203,891 7,280,460 5,457,669 6,894,963 7,142,495 7,209,423 7,283,729 5,561,649 6,895,593 7,145,861 7,210,067 7,286,454 5,705,762 6,937,815 7,146,624 7,228,062 7,304,938 6,043,912 6,996,327 7,151,729 7,245,566 6,438,099 7,009,926 7,161,879 7,245,567 6,467,061 7,085,221 7,164,647 7,257,065 6,556,521 7,088,649 7,167,437 7,263,045 6,578,163 7,092,327 7,173,891 7,269,110 6,697,307 7,099,566 7,177,250 7,272,086 6,728,474 7,123,564 7,194,187 7,272,106
"This product incorporates copyright protection technology that is protected by U.S. patents and other intellectual property rights. Use of this copyright protection technology must be authorized by Macrovision, and is intended for home and other limited viewing uses only unless otherwise authorized by Macrovision. Reverse engineering or disassembly is prohibited.
HT-BD1250A_XAA_0703-1.indd 6

Contents

KEY FEATURES OF YOUR NEW BLU-RAY HOME THEATER SAFETY INFORMATION

GETTING STARTED

DESCRIPTION

REMOTE CONTROL

CONNECTIONS
Player Features Blu-ray Disc Features Whats Included
Safety Warnings Precautions
Before Reading the Users Manual Disc Type and Characteristics

19, 61, 65 03, 40, 60, 61 15, 18, 19 15, 57, 64 57, 58 50, 51, 52, 53, 55 03, 18 18, 40, 48, 54, 59, 60, 62 61, 95, 18 03, 15, 18, 25 18, 40 19, 57, 63, 59, 60, 69 15, 17, 18, 40, 48, 54, 60, 58, 03, 54
Daytron Dynasty Emerson Fisher Funai Futuretech General Electric (GE) Hall Mark Hitachi Inkel JC Penny JVC KTV KEC KMC LG (Goldstar) Luxman LXI (Sears) Magnavox Marantz Matsui MGA Mitsubishi/MGA
03, 15, 40, 46, 59, 61, 64, 82, 83, 84, 85 19, 03 06, 40, 56, 59, 66, 67, 15, 18, 50, 59, 56, 59, 67, 59, 61, 87, 88 03, 15, 01, 15, 16, 17, 37, 38, 39, 40, 41, 42, 43, 19, 54, 56, 59, 60, 62, 63, 65, 71 15, 17, 18, 48, 54, 59, 60, 62, 72, 89 40, 18, 40 18, 40, 59, 60, 75
HT-BD1250A_XAA_0703-1.indd 19

4:58:11

Connections
This section involves various methods of connecting the Blu-ray Home Theater to other external components. Before moving or installing the product, be sure to turn off the power and disconnect the power cord.

CONNECTING THE SPEAKERS

Position of the Blu-ray Home Theater
Place it on a stand or cabinet shelf, or under the TV stand.
Selecting the Listening Position
The listening position should be located about 2.5 to 3 times the distance of the TV's screen size away from the TV. Example : For 32" TVs 6~8feet (2~2.4m) For 55" TVs 11~13feet (3.5~4m))

Front Speakersei

Place these speakers in front of your listening position, facing inwards (about 45) toward you. Place the speakers so that their tweeters will be at the same height as your ear. Align the front face of the front speakers with the front face of the center speaker or place them slightly in front of the center speakers.

Center Speaker

It is best to install it at the same height as the front speakers. You can also install it directly over or under the TV.

Surround Speakers

Place these speakers to the side of your listening position. If there isn't enough room, place these speakers so they face each other. Place them about 2 to 3 feet (60 to 90cm) above your ear, facing slightly downward. the center speakers, the rear speakers are used to handle mainly sound effects and sound will not * Unlike fromfront and the time. come them all

Subwoofer

The position of the subwoofer is not so critical. Place it anywhere you like.

Depending on your TV, certain HDMI output resolutions may not work. HDMI automatically within 10 seconds.
If an HDMI cable is connected from the player to a TV, the Blu-ray Home Theaters output is set to If you are using the Anynet + feature (see page 46) and Component and HDMI are both
connected, HDMI mode is automatically selected.
When you connect the player to the TV using the HDMI cable for the rst time or to a new TV, the
HDMI output resolution will automatically be set to the highest provided by the TV.
If you connect a Samsung TV to the Blu-ray Home Theater using an HDMI cable, the player can
be easily operated using the TV remote control. (This is only available with Samsung TVs that support the Anynet+ feature.) (See page 46) If the HDMI cable is connected or removed during playback of a CD-DA, MP3 or JPEG le, the player will stop playing. After making the video connection, set the Video input source on your TV to match the corresponding Video output (HDMI, Component or Composite) on your Blu-ray Home Theater. See your TV owner's manual for more information on how to select the TV's Video Input source. If you have set the remote control to operate your TV, press the SOURCE button on the remote control and select HDMI as the external source of the TV.
HDMI Auto Detection Function
The player's video output will automatically change to HDMI mode when connecting an HDMI cable while power is on. For possible HDMI resolutions, see page 43.
HDMI (High Denition Multimedia Interface) HDMI is an interface that enables the digital transmission of video and audio data with just a single connector. Using HDMI, the Blu-ray Home Theater transmits a digital video and audio signal and displays a vivid picture on a TV having an HDMI input jack.
HT-BD1250A_XAA_0703-1.indd 24
HDMI connection description HDMI connector - Supports video and digital audio data. - HDMI outputs only a pure digital signal to the TV. - If your TV does not support HDCP (High-bandwidth Digital Content Protection), random noise appears on the screen. Why does Samsung use HDMI? Analog TVs require an analog video/audio signal. However, when playing a BD/DVD, the data transmitted to a TV is digital. Therefore either a digital-to-analog converter (in the Blu-ray Home Theater) or an analog-to-digital converter (in the TV) is required. During this conversion, the picture quality is degraded due to noise and signal loss. HDMI technology is superior because it requires no D/A conversion and is a pure digital signal from the player to your TV. What is the HDCP? HDCP (High-band width Digital Content Protection) is a system for protecting BD/DVD content outputted via HDMI from being copied. It provides a secure digital link between a video source (PC, DVD. etc) and a display device (TV, projector. etc). Content is encrypted at the source device to prevent unauthorized copies from being made. What is Anynet+? Anynet+ is a convenient function that offers linked operation of this unit through Samsung TVs with the Anynet+ feature. - If your Samsung TV has an logo, then it supports the Anynet+ function. - If you turn on the player and insert a disc, the player will start playing the disc, and the TV will turn on automatically and switch to HDMI mode. - If you turn on the player and press the PLAY button with a disc already inserted, the TV will immediately turn on and switch to HDMI mode. What is BD Wise? BD Wise is Samsung's latest inter-connectivity feature. - When you connect Samsung products with BD-Wise to each other via HDMI, the optimum resolution will be set automatically.

Proxy NTP Server Network Connection Test
BD-LIVE Internet : Allow (Vaild Only) Allow(All) Connection Allow(Valid Only) Prohibit
What is a valid certicate? When the Blu-ray Home Theater uses BD-LIVE to send the disc data and request to the server to certify the disc, the server uses the transferred data to check if the disc is valid and sends the certicate back to the player.
The Internet connection may be restricted while you are using BD-LIVE contents.
HT-BD1250A_XAA_0715-2.indd 55

5:00:24

BD data management
BD Data (stored in external USB ash memory) is Blu-ray Disc content such as trailers and other special features downloaded from the BD-LIVE service or Blu-ray Discs.
* You must have a minimum 1GB USB Memory device inserted in one of the USB slots in order to download content from BD-LIVE.

SYSTEM DEVICE MANAGEMENT

You can manage user data stored in BD data.
1. With the unit in Stop mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or button. 3. Press the buttons to select System, then press the ENTER or button. 4. Press the buttons to select BD Data Management, then press the ENTER or button.
Time Zone Clock Set Power On/Off sound : On System Language Audio Display HDMI Network Parental
BD Data Management System Update
- To delete the ash memory 1. Press the ENTER button to select BD Data Delete. The message "All BD data will be deleted. Do you want to continue?" will be displayed. 2. Press the button to select Yes, then press the ENTER button. Description of Device(Storage) Information on the Player Total Size : Total size of the Device(Storage). Available Size : Available size of the Device(Storage).
Time Zone Clock Set Power On/Off sound : On
System BD Data Management Management BD Data
Language System Update Current Device : External Flash Memory TotalAudio : 953MB Available Size : 889MB Size Display HDMI Network Parental

BD Data Delete

Memory size information on the current device(storage) is located to the right of the BD Data Management menu. device in the middle of the playback.
In the external memory mode, disc playback will be stopped if you disconnect the USB We recommend using an USB device that supports USB 2.0 protocols, FAT32 format and
4MB or more read /write speed.
The Resume Play function may not work after formatting the storage device.
HT-BD1250A_XAA_0715-2.indd 56

5:00:29

System upgrade
Samsung may offer upgrades to your Blu-ray Home Theater's rmware in the future. To upgrade this rmware you must : 1. Go to samsung.com and refer to the SUPPORT page to download the latest rmware. You can use a CD-R or a USB ash drive to perform the rmware upgrade. For more information, see Upgrade Manual at the website mentioned above. or 2. Connect the network (see pages 30~31) and follow the steps below.

SYSTEM UPGRADE

FIRMWARE UPGRADE
1. With the unit in Stop mode/No Disc mode, press the MENU button. 2. Press the buttons to select Setup, then press the ENTER or button. 3. Press the buttons to select System, then press the ENTER or button. 4. Press the buttons to select System Update, then press the ENTER or button.
System Language Audio Display HDMI Network Parental
Clock Set Power On/Off sound BD Data Menagement System Language Audio Display HDMI Network Parental

System Update

5. The player will check the cable or network connection status automatically. The connection checking window will be displayed. If the upgrade is possible : You will see information on the current and new versions of rmware in a message box.
Clock Set Power On/Off sound System Update BD Data Menagement System

3 System Update 4

If the upgrade is not possible : You will see the following description in the message box. If the cable is not connected : Ethernet cable is not connected. Please, check the Ethernet cable If the network connection has failed : This system can not connect to internet for update. Please, check the network setup If no latest version is released (the latest version has been already installed) : "The latest version of the rmware is already installed. There is no need to update." If there is a disc in the player : "Please maintain "No Disc" state for network update." This indicates that you must remove all discs from the unit to perform the update. If the server service is not available : Update Server is under maintenance. Please try again later.
Language Audio Now, Checking. Display Please wait. HDMI Network Parental
Clock Set Power On/Off sound BD Data System Update Menagement System
System Update Language Audionew update data was found. The Display Current Version : XXXXX HDMI New Version : XXXXX

Network Parental Start

Clock Set Power On/Off sound System Update Menagement BD Data
System 3 System Update 4 Language Audio system can not connect This Displayto internet for update. Please, check the network setup. HDMI

Network Parental

HT-BD1250A_XAA_0715-3.indd 57

5:56:08

6. To perform the system upgrade, press the buttons to select Start and then press the ENTER button.
Clock Set Power On/Off sound System Update Menagement BD Data System
Language Audionew update data was found. The Current Version : XXXXX Display New Version : XXXXX HDMI Network Parental Start Cancel
7. The system update gets started.

DVD up to 8.

Playing Time : Allows playback of the lm from a desired time. You must enter the starting time as a reference.
The time search function does not operate on some discs.
Subtitle : Refers to the subtitle languages available in the disc. You will be able to choose the subtitle
languages or, if you prefer, turn them off from the screen. A Blu-ray Disc can contain up to 255 subtitle languages, and a DVD up to 32.
Angle : When a Blu-ray Disc/DVD contains multiple angles of a particular scene, you can use the ANGLE

function.

BONUSVIEW Video/BONUSVIEW Audio : You can make BONUSVIEW Video or BONUSVIEW Audio settings if the
current title of a Blu-ray Disc appears in the PIP section. The BONUSVIEW Video / BONUSVIEW Audio options, however, will be disabled with a Blu-ray Disc that does not support the PIP feature.
Picture Mode : This function enables you to adjust video quality when you are connected to a TV via HDMI.
- Dynamic : Choose this setting to increase Sharpness. - Normal : Choose this setting for most viewing applications. - Movie : This is the best setting for watching movies. - User : The user can adjust the sharpness and noise reduction function respectively.
HT-BD1250A_XAA_0715-3.indd 60

5:56:38

USING THE DISC MENU & POPUP/TITLE MENU

Using the Disc Menu

1. During playback, press the DISC MENU button on the remote control. 2. Press the buttons to make the desired selection, then press the or ENTER button. The Disc menu setup items may vary from disc to disc. WATCHING A MOVIE
Depending on the disc, the Disc Menu may not be available.

Using the Title Menu

1. During playback, press the TITLE MENU button on the remote control. 2. Press the buttons to make the desired selection, then press the ENTER button. The Title menu setup options may vary from disc to disc.
Depending on the disc, the Title Menu may not be available.
Title Menu will only be displayed if there are at least two titles on the disc.

Playing the Title List

CD BD-RE
1. With the unit in Stop mode/Playback mode, press the DISC MENU or TITLE MENU button. 2. Press the buttons to select an entry you want to play from Title List, then press the or ENTER button. The selected entry (title) will be played back.
Title 008 Title 009 Title 010 Title 011 Title 012 Title 013 Title 014
00:04:36 00:04:17 00:04:11 00:04:07 00:04:46 00:04:21 00:03:43

Using the Popup Menu

1. During playback, press the POPUP MENU button on the remote control. 2. Press the buttons or ENTER button to select the desired menu. The Popup menu setup options may vary from disc to disc.

Information about the primary / secondary mode will be also displayed if the Blu-ray Disc
has a PIP section. Use the button to switch between primary and secondary audio modes.
The indicator will not be displayed on the screen if the PIP section does not contain

any PIP audio settings.

SELECTING THE SUBTITLE LANGUAGE
You can select a desired subtitle quickly and easily with the SUBTITLE button.
Using the SUBTITLE button
1. Press the SUBTITLE button. The subtitle changes when the button is pressed repeatedly. The subtitle languages are represented by abbreviations. 2. To remove the Subtitle bar, press the RETURN button.

Subtitle 0/2 Off

HT-BD1250A_XAA_0715-3.indd 63

5:56:47

Using the INFO button 1. During playback, press the INFO button on the remote control. 2. Press the buttons to select Subtitle. 3. Press the buttons on the remote control to select the desired subtitle language.
Depending on the Blu-ray Disc / DVD, you may be able to change the desired subtitle in the Disc Menu. Press the DISC MENU button. on all Blu-ray Discs/DVDs.
This function depends on what subtitles are encoded on the disc and may not be available A Blu-ray Disc can contain up to 255 subtitle languages and a DVD up to 32. Information about the primary / secondary mode will be also displayed if the Blu-ray Disc

has a PIP section.

This function changes both the primary and secondary subtitles at the same time. The total number of subtitles is the sum of the primary and secondary ones.
CHANGING THE CAMERA ANGLE
When a Blu-ray Disc/DVD contains multiple angles of a particular scene, you can use the ANGLE function.

Using the ANGLE function

1. During playback, press the INFO button on the remote control. 2. Press the buttons to select Angle. 3. Press the buttons or you can use the number buttons on the remote control to select the desired angle.
BD Title Chapter Playing Time Audio Subtitle Angle Picture Mode Change : : : : : : : 001/500 001/001 00:00:00 1/5 ENG 2CH NONE 01/01 Normal Move Info

HT-BD1250A_XAA_0715-3.indd 72

Using the USB function

PLAYING MEDIA FILES USING THE USB HOST FEATURE
You can enjoy media les such as pictures and music saved on an MP3 player, USB memory stick or digital camera. 1. Connect the USB device to the USB port on the side of the unit. 2. USB Connected appears on the display screen and then disappears. 3. USB icon is displayed on the Setup Menu.

USING THE USB FUNCTION

Safe USB Removal
To prevent damage to the data stored in the USB device, perform safe removal before disconnecting the USB cable. Press the YELLOW(C) button. The display will show Now. You can remove USB safely. Remove the USB cable.
To listen to your music les with 5.1 channel home theater sound, you must set the Dolby Pro Logic II mode to Matrix. (See page 71)

Skip Forward/Back

During playback, press the #, $ button. When there is more than one le and you press the $ button, the next le is selected. When there is more than one le and you press the # button, the previous le is selected.
HT-BD1250A_XAA_0715-3.indd 73

USB Host Specication

Supports USB 1.1 or USB 2.0 compliant devices. Supports devices connected using the USB A type cable. Supports UMS (USB Mass Storage Device) V1.0 compliant devices. Supports the device of which the connected drive is formatted in the FAT(FAT, FAT16, FAT32) le system. Does not support a device that requires installing a separate driver on the PC (Windows). Does not support connection to a USB hub. A USB device that is connected using the USB extension cable may not be recognized. A USB device requiring a separate power source needs to be connected to the player with the separate power connection. If the connected device has multiple drives (or partitions) installed, only one drive (or partition) can be connected. A device supporting USB 1.1 alone may cause a difference in the picture quality, depending on the device. USB Host Specication

Non-compliance

Operational Limitations
USB Devices that can be used with the Home Theater
1. USB Storage Device 2. MP3 Player 3. Digital Camera 4. Removable HDD Removable HDDs equipped with less than 160 Gbytes are supported. Removable HDDs equipped with 160Gbytes or more may not be recognized, depending on the device. If the connected device does not work due to insufcient power supply, you can use a separate power cable to supply power so that it can work properly. The connector of the USB cable may differ, depending on the manufacturer of the USB device. 5. USB card Reader: One slot USB card reader and Multi slot USB card reader. Depending on the manufacturer. the USB card reader may not be supported. If you install multiple memory devices into a multi card reader, you may experience problems.

Supported le Formats

The iPod fails to connect.

Playback does not start.

Playback does not start immediately when the Play/Pause button is pressed. Sound is not produced.
Sound can be heard only from a few speakers and not all 6.
Dolby Digital 5.1 CH Surround Sound is not produced.
The remote control does not work.
Disc is rotating but no picture is produced. Picture quality is poor and picture is shaking. Audio language and subtitles do not work. Menu screen does not appear even when the menu function is selected. 92
HT-BD1250A_XAA_0715-3.indd 92

5:58:07

SYMPTOM Aspect ratio cannot be changed.
Check/Remedy You can play 16:9 BD/DVDs in 16:9 Wide mode, 4:3 Letter Box mode, or 4:3 Pan - Scan mode, but 4:3 BD/DVDs can be seen in 4:3 ratio only. Refer to the Blu-ray Disc jacket and then select the appropriate function. Turn off the power and hold the STOP ( I ) button on the main unit for longer than 5 seconds. Using the RESET function will erase all stored settings. Do not use this unless necessary. While (NO DISC) message appears on the display of main unit, hold the main unit's STOP ( I ) button for longer than 5 seconds. INITIAL appears on the display and all settings will return to the default values. Press the POWER button. Using the RESET function will erase all stored settings. Do not use this unless necessary. Is the antenna connected properly? If the antenna's input signal is weak, install an external FM antenna in an area with good reception. If the OPEN/CLOSE ( ) button is pressed while listening to TV audio using the D.IN or AUX functions, the BD/DVD functions are turned on and this mutes the TV audio. The features or action cannot be completed at this time because: 1. The BD/DVDs software restricts it. 2. The BD/DVDs software doesnt support the feature (e.g., angles) 3. The feature is not available at the moment. 4. Youve requested a title or chapter number or search time that is out of range. Press the STOP ( I ) button (in front panel) for more than 5 seconds with no disc inside. All settings will revert to the factory settings. Check the connection between the TV and the HDMI jack of the Blu-ray Home Theater. Check if your TV supports 480p/720p/1080i/1080p HDMI input resolution. If random noise appears on the screen, it means that TV does not support HDCP (High-bandwidth Digital Content Protection). Check the Proxy is Off(Setup -> Network -> Proxy)

HT-BD1250A_XAA_0715-3.indd 96
Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of running the Program is not restricted, and the output from the Program is covered only if its contents constitute a work based on the Program (independent of having been made by running the Program). Whether that is true depends on what the Program does. 1. You may copy and distribute verbatim copies of the Programs source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and give any other recipients of the Program a copy of this License along with the Program. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Program or any portion of it, thus forming a work based on the Program, and copy and distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) You must cause the modied les to carry prominent notices stating that you changed the les and the date of any change. b) You must cause any work that you distribute or publish, that in whole or in part contains or is derived from the Program or any part thereof, to be licensed as a whole at no charge to all third parties under the terms of this License. c) If the modied program normally reads commands interactively when run, you must cause it, when started running for such interactive use in the most ordinary way, to print or display an announcement including an appropriate copyright notice and a notice that there is no warranty (or else, saying that you provide a warranty) and that users may redistribute the program under these conditions, and telling the user how to view a copy of this License. (Exception: if the Program itself is interactive but does not normally print such an announcement, your work based on the Program is not required to print an announcement.) These requirements apply to the modied work as a whole. If identiable sections of that work are not derived from the Program, and can be reasonably considered independent and separate works in themselves, then this License, and its terms, do not apply to those sections when you distribute them as separate works. But when you distribute the same sections as part of a whole which is a work based on the Program, the distribution of the whole must be on the terms of this License, whose permissions for other licensees extend to the entire whole, and thus to each and every part regardless of who wrote it. Thus, it is not the intent of this section to claim rights or contest your rights to work written entirely by you; rather, the intent is to exercise the right to control the distribution of derivative or collective works based on the Program. In addition, mere aggregation of another work not based on the Program with the Program (or with a work based on the Program) on a volume of a storage or distribution medium does not bring the other work under the scope of this License. 3. You may copy and distribute the Program (or a work based on it, under Section 2) in object code or executable form under the terms of Sections 1 and 2 above provided that you also do one of the following: a) Accompany it with the complete corresponding machine-readable source code, which must be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, c) Accompany it with the information you received as to the offer to distribute corresponding source code. (This alternative is allowed only for noncommercial distribution and only if you received the program in object code or executable form with such an offer, in accord with Subsection b above.) The source code for a work means the preferred form of the work for making modications to it. For an executable work, complete source code means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the executable. However, as a special exception, the source code distributed need not include anything that is normally distributed (in either source or binary form) with the major components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable.

HT-BD1250A_XAA_0715-3.indd 100
In other cases, permission to use a particular library in non-free programs enables a greater number of people to use a large body of free software. For example, permission to use the GNU C Library in non-free programs enables many more people to use the whole GNU operating system, as well as its variant, the GNU/Linux operating system. Although the Lesser General Public License is Less protective of the users freedom, it does ensure that the user of a program that is linked with the Library has the freedom and the wherewithal to run that program using a modied version of the Library. The precise terms and conditions for copying, distribution and modication follow. Pay close attention to the difference between a work based on the library and a work that uses the library. The former contains code derived from the library, whereas the latter must be combined with the library in order to run. TERMS AND CONDITIONS FOR COPYING, DISTRIBUTION AND MODIFICATION 0. This License Agreement applies to any software library or other program which contains a notice placed by the copyright holder or other authorized party saying it may be distributed under the terms of this Lesser General Public License (also called this License). Each licensee is addressed as you. A library means a collection of software functions and/or data prepared so as to be conveniently linked with application programs (which use some of those functions and data) to form executables. The Library, below, refers to any such software library or work which has been distributed under these terms. A work based on the Library means either the Library or any derivative work under copyright law: that is to say, a work containing the Library or a portion of it, either verbatim or with modications and/or translated straightforwardly into another language. (Hereinafter, translation is included without limitation in the term modication.) Source code for a work means the preferred form of the work for making modications to it. For a library, complete source code means all the source code for all modules it contains, plus any associated interface denition les, plus the scripts used to control compilation and installation of the library. Activities other than copying, distribution and modication are not covered by this License; they are outside its scope. The act of running a program using the Library is not restricted, and output from such a program is covered only if its contents constitute a work based on the Library (independent of the use of the Library in a tool for writing it). Whether that is true depends on what the Library does and what the program that uses the Library does. 1. You may copy and distribute verbatim copies of the Librarys complete source code as you receive it, in any medium, provided that you conspicuously and appropriately publish on each copy an appropriate copyright notice and disclaimer of warranty; keep intact all the notices that refer to this License and to the absence of any warranty; and distribute a copy of this License along with the Library. You may charge a fee for the physical act of transferring a copy, and you may at your option offer warranty protection in exchange for a fee. 2. You may modify your copy or copies of the Library or any portion of it, thus forming a work based on the Library, and copy and distribute such modications or work under the terms of Section 1 above, provided that you also meet all of these conditions: a) The modied work must itself be a software library. b) You must cause the les modied to carry prominent notices stating that you changed the les and the date of any change. c) You must cause the whole of the work to be licensed at no charge to all third parties under the terms of this License. d) If a facility in the modied Library refers to a function or a table of data to be supplied by an application program that uses the facility, other than as an argument passed when the facility is invoked, then you must make a good faith effort to ensure that, in the event an application does not supply such function or table, the facility still operates, and performs whatever part of its purpose remains meaningful. (For example, a function in a library to compute square roots has a purpose that is entirely well-dened independent of the application. Therefore, Subsection 2d requires that any application-supplied function or table used by this function must be optional: if the application does not supply it, the square root function must still compute square roots.)

HT-BD1250A_XAA_0715-3.indd 103
If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances. It is not the purpose of this section to induce you to infringe any patents or other property right claims or to contest validity of any such claims; this section has the sole purpose of protecting the integrity of the free software distribution system which is implemented by public license practices. Many people have made generous contributions to the wide range of software distributed through that system in reliance on consistent application of that system; it is up to the author/donor to decide if he or she is willing to distribute software through any other system and a licensee cannot impose that choice. This section is intended to make thoroughly clear what is believed to be a consequence of the rest of this License. 12. If the distribution and/or use of the Library is restricted in certain countries either by patents or by copyrighted interfaces, the original copyright holder who places the Library under this License may add an explicit geographical distribution limitation excluding those countries, so that distribution is permitted only in or among countries not thus excluded. In such case, this License incorporates the limitation as if written in the body of this License. 13. The Free Software Foundation may publish revised and/or new versions of the Lesser General Public License from time to time. Such new versions will be similar in spirit to the present version, but may differ in detail to address new problems or concerns. Each version is given a distinguishing version number. If the Library species a version number of this License which applies to it and any later version, you have the option of following the terms and conditions either of that version or of any later version published by the Free Software Foundation. If the Library does not specify a license version number, you may choose any version ever published by the Free Software Foundation. 14. If you wish to incorporate parts of the Library into other free programs whose distribution conditions are incompatible with these, write to the author to ask for permission. For software which is copyrighted by the Free Software Foundation, write to the Free Software Foundation; we sometimes make exceptions for this. Our decision will be guided by the two goals of preserving the free status of all derivatives of our free software and of promoting the sharing and reuse of software generally. NO WARRANTY 15. BECAUSE THE LIBRARY IS LICENSED FREE OF CHARGE, THERE IS NO WARRANTY FOR THE LIBRARY, TO THE EXTENT PERMITTED BY APPLICABLE LAW. EXCEPT WHEN OTHERWISE STATED IN WRITING THE COPYRIGHT HOLDERS AND/OR OTHER PARTIES PROVIDE THE LIBRARY AS IS WITHOUT WARRANTY OF ANY KIND, EITHER EXPRESSED OR IMPLIED, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. THE ENTIRE RISK AS TO THE QUALITY AND PERFORMANCE OF THE LIBRARY IS WITH YOU. SHOULD THE LIBRARY PROVE DEFECTIVE, YOU ASSUME THE COST OF ALL NECESSARY SERVICING, REPAIR OR CORRECTION. 16. IN NO EVENT UNLESS REQUIRED BY APPLICABLE LAW OR AGREED TO IN WRITING WILL ANY COPYRIGHT HOLDER, OR ANY OTHER PARTY WHO MAY MODIFY AND/OR REDISTRIBUTE THE LIBRARY AS PERMITTED ABOVE, BE LIABLE TO YOU FOR DAMAGES, INCLUDING ANY GENERAL, SPECIAL, INCIDENTAL OR CONSEQUENTIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.

END OF TERMS AND CONDITIONS
How to Apply These Terms to Your New Libraries If you develop a new library, and you want it to be of the greatest possible use to the public, we recommend making it free software that everyone can redistribute and change. You can do so by permitting redistribution under these terms (or, alternatively, under the terms of the ordinary General Public License). To apply these terms, attach the following notices to the library. It is safest to attach them to the start of each source le to most effectively convey the exclusion of warranty; and each le should have at least the copyright line and a pointer to where the full notice is found.
HT-BD1250A_XAA_0715-3.indd 104
<one line to give the librarys name and an idea of what it does.> Copyright (C) <year> <name of author> This library is free software; you can redistribute it and/or modify it under the terms of the GNU Lesser General Public License as published by the Free Software Foundation; either version 2.1 of the License, or (at your option) any later version. This library is distributed in the hope that it will be useful, but WITHOUT ANY WARRANTY; without even the implied warranty of MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU Lesser General Public License for more details. You should have received a copy of the GNU Lesser General Public License along with this library; if not, write to the Free Software Foundation, Inc., 59 Temple Place, Suite 330, Boston, MA 02111-1307 USA Also add information on how to contact you by electronic and paper mail. You should also get your employer (if you work as a programmer) or your school, if any, to sign a copyright disclaimer for the library, if necessary. Here is a sample; alter the names: Yoyodyne, Inc., hereby disclaims all copyright interest in the library `Frob (a library for tweaking knobs) written by James Random Hacker. signature of Ty Coon, 1 April 1990 Ty Coon, President of Vice Thats all there is to it!

OpenSSL License

Copyright (c) 1998-2007 The OpenSSL Project. All rights reserved. Redistribution and use in source and binary forms, with or without modication, are permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2. Redistributions in binary form must reproduce the above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. 3. All advertising materials mentioning features or use of this software must display the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit. (http:// www.openssl.org/)" 4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to endorse or promote products derived from this software without prior written permission. For written permission, please contact opensslcore@openssl.org. 5. Products derived from this software may not be called "OpenSSL" nor may "OpenSSL" appear in their names without prior written permission of the OpenSSL Project. 6. Redistributions of any form whatsoever must retain the following acknowledgment: "This product includes software developed by the OpenSSL Project for use in the OpenSSL Toolkit (http://www.openssl. org/)" THIS SOFTWARE IS PROVIDED BY THE OpenSSL PROJECT ``AS IS'' AND ANY EXPRESSED OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE OpenSSL PROJECT OR ITS CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.