Shielded interface cables and I/O cords must be used for this equipment to comply with the relevant FCC regulations. Changes or modifications not expressly approved in writing by Samsung may void the users authority to operate this equipment.

IC COMPLIANCE NOTICE

This Class B digital apparatus meets all requirements of the Canadian Interference-Causing Equipment Regulations of ICES-003. Cet appareil numerigue de la Classe B respecte toutes les exigences du Reglement ICES-003 sur le Materiel brouilleur du Canada.
EC Declaration of Conformity
We, SAMSUNG ELECTRONICS CO.,LTD #259, Gong Dan-Dong, Gumi-City, Kyung Buk, Korea declare sole responsibility that the
ML-7300, ML-7300N Laser Printer
meets the intent of Directive 89/336/EEC for Electromagnetic Compatibility and Low Voltage Directive 73/23/EEC. Compliance was demonstrated to the following specifications as listed in the official journal of the European Communities: Electro Magnetic Interference (EMI): EN 55022 Radiated, Class B EN 55022 Conducted, Class B EN 61000-3-2 Power Harmonics EN 61000-3-3 Voltage Fluctuations and Flicker EN 55024 EN EN EN EN EN EN EN - Electro Mangnetic Susceptibility (EMS) 61000-4-2 Electrostatic Discharge 61000-4-3 RF Electromagnetic Field 61000-4-4 Fast Transients 61000-4-5 Surges 61000-4-6 RF Common Mode 61000-4-8 Power Frequency Magnetic Field 61000-4-11 Voltage Dips and Interruptions

EN 60950-Safety

Safety information
Safety and Regulatory Listing for this printer. PRODUCT SAFETY USA & CANADA Evaluated by UL according to UL 1950 and CSA C22.2 No. 950 for C-UL EEC(Europe) IEC 60950/EN 60950(TUV GS Certification) CB IEC 60950 LASER SAFETY EEC(Europe) USA
HD 194. & EN CFR, Chapter 1, Subchapter J(CDRH Certified)
Replacing the fitted plug (UK Only)

Important

The mains lead for this machine is fitted with a standard (BS 1363) 13 amp plug and 13 amp fuse. When you change or examine the fuse, you must re-fit the correct 13 amp fuse. You then need to replace the fuse cover. If you have lost the fuse cover, do not use the plug until you get another fuse cover from the people who sold you the machine. The 13 amp plug is the most widely used type in the UK. However, some buildings (mainly old ones) do not have normal 13 amp plug sockets. You need to buy a suitable plug adaptor. Do not remove the moulded plug.

Rear cover Parallel interface connector

Power connector

Setting Up Your Printer
This chapter provides step by step information on setting up your printer. Topics included in this chapter are:
STEP 1: Unpacking Your Printer STEP 2: Installing Toner Cartridge STEP 3: Load Paper STEP 4: Connecting the Parallel Cable STEP 5: Connecting the AC Power Cord STEP 6: Testing the Printer! STEP 7: Setting Up the Printer Driver

Unpacking Your Printer

Items Supplied
When you start unpacking the box of your printer, you will find the following items in addition to your printer.

Toner cartridge

CD-ROM Disk

Power cord*

This manual
Notes: If you find that any of the above items are missing or damaged,
contact your local dealer. A printer cable is not included in the package items. Cable specifications - The parallel cable should be compatible with the centronics parallel interface and IEEE standard 1284. * Power cord may differ from one country to another.
S ETTING U P Y OUR P RINTER

Preparation

During the storage and transport of your printer, adhesive tape is used to block some of the elements that may move or open unexpectedly and consequently be damaged.
1 Before connecting up your printer
and starting to use it, you must remove all the adhesive tapes, as illustrated in the figure below.
2 Slide the tray out of the printer.
Remove the packaging material from the tray.
2.2 S ETTING U P Y OUR P RINTER
Installing Toner Cartridge
To install a toner cartridge in your printer proceed as follows.
1 Remove the toner cartridge from

its packaging.

Notes: Do not remove the cartridge
from its packaging until you are ready to use it. Do not expose the cartridge to light, it could damage the cartridge permanently.
2 Open the top cover of the printer
by pressing the button on the right side of the printer.
3 Rotate the cartridge and gently
shake it from side to side to distribute the toner evenly inside the cartridge.
4 Position the cartridge as shown
with the arrow pointing into the printer. Slide the cartridge into the printer as far as it will go.

5 Close the top cover.

Notes: If toner gets on your clothing, wipe it off with a dry cloth and wash clothing
in cold water. When printing text at 5% coverage, a toner cartridge lasts an average of 10,000pages in simplex mode.
2.4 S ETTING U P Y OUR P RINTER

Load Paper

To load paper in the tray, proceed as follows.
1 Pull the Tray1 completely out of

the printer.

2 Squeeze the back of the rear
paper guide and slide it to the desired paper size until it clicks into place. The paper sizes are indicated on the bottom of the tray1.

Rear paper guide

3 Lift the rear right guide and slide
it to match the width of the paper. The paper sizes are indicated on the bottom of the tray.
4 Squeeze the width guide and slide
it to the far right side of the tray.

Width guide

Rear right guide
Notes: If the tray is not properly adjusted, the printer might display an error
message or paper might jam.
5 Place the paper against the rear

paper guide as shown.

Paper Limit Line

Printing side(down)

Notes:
Do not fold or crease the paper. Place the paper with the recommended print side face down. Dont exceed the paper limit line indicated on the tray.
2.6 S ETTING U P Y OUR P RINTER
6 Squeeze the width guide and slide
it to the left until it lightly rests against the edge of the paper.
7 Make sure the paper is under

the tab on the tray.

8 Gently slide the tray back into the
printer. The printer automatically senses the size of paper loaded if the tray1 is adjusted correctly.
Notes: If jam 0 often occurs when 24lb letter, legal or folio size paper is used, push down the lever on the left side of the tray as shown in the figure to ensure proper paper feeding.
Connecting the Parallel Cable
To print from computer software, you need to connect your printer to your computer with a parallel interface cable.
Cable Specifications (Not provided)
The parallel cable should be compatible with the Centronics R parallel interface and IEEE standard 1284. If you purchase a parallel cable, ensure that it : Is compatible with Centronics interface. Supports bi-directional communications(IEEE standard 1284). Is shielded. Has the appropriate connector : - 25 pin D-Sub connector on the computer side. - Amphenol 36 connector on the printer side.

language.

2.12 S ETTING U P Y OUR P RINTER

Installing the Driver

Hardware Requirements
To install and run the PCL printer driver, you must have the following minimum hardware configuration. Windows 95 or Windows 98 - PC-compatible 486 computer or better. - 32MB RAM - 200MB available hard-disk space. Windows NT 4.0 or Windows 2000 - PC-compatible pentium 133MHz computer or better. - 64MB RAM - 650MB available hard-disk space. CD-ROM Drive.

Software Requirements

To install and run the printer driver, you must be running one of the following platforms. Windows 95, Windows 98, Windows NT 4.0, Windows 2000. Macintosh System 7.5 or later.

Install Procedure

To install the printer driver on your hard disk, make backup copies of the print driver CD. Keep the original CD in a safe place and use the copies.
Notes: I do not have a CD-ROM driver
If you have access to another computer with a CD-ROM drive, you can use the Make diskette utility in Windows to create the disks you need for the installation. Go to Appendix E, Installing Software form Diskettes
Installing the Printer Software from the CD-ROM

SUNG ML-73 AM

1 Place the CD-ROM in the CD-ROM drive. Install will start
automatically. If the CD-ROM drive does not automatically run: Select Run from the Start menu, and type x:\cdsetup.exe in the Open box (where x is the drive letter for the CD-ROM drive), and then click OK.

Notes: If the New

Hardware Found box appears during the installation procedure, click the x in the upper right corner of the box, or click Cancel.
2 When the opening screen appears, select the appropriate
3 Click Install the Samsung Software-I on your PC.
4 Follow the instructions on the screen to complete

the installation.

2.14 S ETTING U P Y OUR P RINTER
Notes: To Install Shared Win 95/98 Printer Driver from NT Server to Client PC
1 Select Sharing in Properties of the printer driver. 2 Select Windows 95 in Alternate Drivers. 3 Type D:\7300\XX\pcl\pcl6\win9x (Where D is your CD-ROM drive letter and XX is the language code*, i.e. eng for English). Install the network printer in the client PC. 4 * Refer to language code (page 2.17) for language codes.
Uninstalling the Printer Driver
An uninstall utility is supplied with the printer driver to enable you to remove the driver and all associated files from your hard disk, if so required. To uninstall the driver, proceed as follows. Select Start Programs Samsung ML-7300 Samsung ML-7300 Driver uninstall from the windows task bar. q The PCL 6 driver is removed from your hard disk.

Notes: Changes made from a software application override the user default
settings made from the printer operator panel.
3.2 U SING O PERATOR PANEL

Changing Printer Setting

To change an operator panel setting, proceed as follows.
1 Make sure the READY message appears on the display. 2 Press On Line.
Result: The OFFLINE message appears on the display and the

printer is off-line.

3 Press Menu until the menu you need appears on the display. 4 Press Item until the menu item you need appears on the display. 5 Press Value until the setting you need appears on the display. 6 Press Enter to save the selection.
Result : An asterisk() appears beside the current user default
setting for that menu item.
A value can be : A phrase or word that describes a setting. A numerical value that you can increase or decrease. An On or Off setting.

Overview of Printer Menu

PRINTING MENU
PAPER MP SIZE COPIES ORIENT TRAY T-MARGIN L-MARGIN DUPLEX AUTO CR WIDE A4 QUALITY

CONFIG MENU

EMUL SWITCH LOCKTRAY PWR SAVE AUTOCONT ECONO JAM RECV TONERLOW

JOB MENU

SRT MODE TIMEOUT DENSITY PAP.TYPE MENU CLR SMET DUP.TOP DUP.LEFT S-BIND L-BIND FUSER CLEAN

TEST MENU

SELFTEST DEMOPAGE

PCL MENU

FONTLIST TYPEFACE SYMBOL LINES PITCH PT.SIZE COURIER
Some menus are displayed only if a required option is installed. They are as follows. I/O MENU
If the serial/LocalTalk option card is installed in your printer

NETWORK MENU

If the Network card(PortThru) is installed in your printer

PS 3 MENU

BAUDRATE ROBU.XON
RESET NIC CFG NET TCP/IP CFG TCP DHCP CFG ADRS IP BYTE 1, 2, 3, 4 SM BYTE 1, 2, 3, 4 GW BYTE 1, 2, 3, 4 BOOTP RARP LPD APL TALK
NETWARE CFG NWAR AUTO EN_8023 EN_II EN_8022 EN_SNAP UPDATE BOOT SVR SV-IP B1 SV-IP B2 SV-IP B3 SV-IP B4 FACTORY DEFAULT PRINT NET CFG

FONTLIST PS.ERROR

3.4 U SING O PERATOR PANEL
Use the PRINTING MENU to define all settings relating to printer input and output, as well as the specific print materials you are using with your printer.

Values and Functions

If the TRAY menu is AUTO, MP, MANUAL A4(country specific), LEGAL, Letter(country specific), EXE, JIS B5, ISO B5, COM-10, MONARCH, DL, C5, POST A6, C6, FOLIO, A5, STS, A6 If the TRAY menu is 1ST A4(country specific), LEGAL, Letter(country specific), EXE, JIS B5, ISO B5, FOLIO If the TRAY menu is OPT A4(country specific), LEGAL, Letter(country specific), EXE, JIS B5, ISO B5, COM-10, MONARCH, DL, C5, FOLIO If the DUPLEX menu is not OFF(SHORT or LONG) A4(country specific), LEGAL, Letter(country specific), FOLIO

MP SIZE

If the DUPLEX menu is OFF A4(country specific), LEGAL, Letter(country specific), EXE, JIS B5,ISO B5, COM-10, MONARCH, DL, C5, POST A6, C6, FOLIO, A5, STS, A6 If the DUPLEX menu is not OFF (SHORT or LONG) A4(country specific), LEGAL, Letter(country specific), FOLIO
Notes: The PAPER SIZE setting identifies the default formatting size for each tray.
It is important to select the correct paper size from the menu when using trays.

COPIES

1 to 999 (1; Factory Default) The COPIES setting determines the number of copies printed for each page. The printer does not automatically collate the copies. For example, if you send three pages to print and set Copies to 2, the printer prints page1, page 1, page 2, page 2, page 3, page 3.

ORIENT

P : Portrait (Factory Default) L : Landscape The ORIENT setting determines how the printing is oriented on the page. P(Portrait) means the printing is parallel to the short edge of the paper. L(Landscape) means the printing is parallel to the long edge of the paper.

Portrait

Landscape
3.6 U SING O PERATOR PANEL
AUTO(Factory Default) 1ST MP OPT(If the optional cassette is installed) MANUAL The TRAY setting identifies the default paper tray. 1ST means that the printer feeds print material from Tray unless it is empty or opened. MP means that the printer feeds print material from Multi-Purpose tray unless it is empty or closed. Use the MANUAL selection when manually feeding envelopes or other print material through the Multi-Purpose tray. OPT is available only if the optional tray 2 is installed. See Optional Tray 2 on page F.17. Auto means that the printer feeds print material from the other tray when one tray is empty. If you are using the same size and type of print material in all the trays, the trays are automatically linked.

T-MARGIN

0.0 ~ 9.9 The T-MARGIN menu item lets you select the top margin of the print materials.

TONERLOW

CONTINU (Factory Default) STOP This setting determines whether the printer can continue printing after the printer detects that the toner is low. If the toner is low and TONERLOW is set to Stop, press the Continue button to print. In that case, replace the toner cartridge or set the TONERLOW menu item to CONTINU.
3.10 U SING O PERATOR PANEL

SWITCH

(If the optional tray 2 is installed)
ON (Factory Default) OFF The ON setting makes the printer supply the paper from another Tray when a tray is empty. In case of the OFF setting, an error message is displayed.

LOCKTRAY

(If the optional tray 2 is installed and the SWITCH menu item is set to ON)
NONE (Factory Default) 1ST OPT MP The tray set to LOCKTRAY doesnt change. For example, if LOCKTRAY is set to MP, the tray is not switched to Multi-Purpose tray.
Use the JOB MENU to define all settings relating to print quality, as well as Menu clear. Item

SRT MODE

(Samsung Resolution Enhancement Technology)
ENHANCE (Factory Default) NORMAL GRAY Use the printers SRT(Samsung Resolution enhancement Technology) setting to produce print with smooth angles, curves, and edges. ENHANCE : Better Text Image GRAY : Better Photo Image

TIMEOUT

0~300 15(Factory Default) The TIMEOUT Setting determines the amount of time (in seconds) the printer waits before printing the last page of a print job that does not end with a command to print the page. When a print timeout occurs, the printer prints the data in the print buffer. 0 : No timeout.

DENSITY

LIGHT MEDIUM (Factory Default) DARK Lighten or darken the print on the page by changing the DENSITY setting. The MEDIUM setting usually produces the best results.
3.12 U SING O PERATOR PANEL

PAP.TYPE

NORMAL (Factory Default) THICK WET TRANSP. The PAP.TYPE setting lets you specify the type of print material installed in each tray. Select NORMAL if the printer material is plain paper. Select THICK if the printer material is thick paper, high cotton paper or envelopes. Select WET if printer material is thin paper(60g) and the air is humid. Select TRANSP. if printer material is transparencies. This value can only be selected if MP or manual has been selected from the Tray menu.

MENU CLR

When you select MENU CLR, the printer resets to the factory default setting for each menu item.
(Samsung Memory Enhancement Technology)

Any error in the process of upgrading may result in disabling PortThru. In this case, perform the following steps.

In SyncThru

Select the Upgrade Firmware menu item under the Maintenance menu in SyncThru. You can see the Choose the Upgrade Firmware File dialog box. Check Wait Printer Request and Set as Default Download. Select the Firmware file Name you downloaded and its path, and then click Start.
You will see the message Please set the values through the FRONT Panel to initiate FLASH Upgrade. Click OK. After this procedure, move to printer which you want to update and do as following procedure.
In Front Panel of the printer
Press On Line. OFFLINE appears on the display. Press Menu until NETWORK MENU appears on the display. Press Item until UPDATE appears on the display. Select YES by pressing the Value button. Press Enter/Cancel. Press Item until BOOT SVR appears on the display. Press Value until WINDOWS appears on the display. Press Enter/Cancel.
3.26 U SING O PERATOR PANEL
Set the IP address of the WINDOWS pc running SyncThru in step1. For example, if the IP address is 155.213.211.12, follow these steps:
a Press Item until SV-IP B1 appears on the display. b Press Value until 155 appears on the display. c Press Enter/Cancel. d Press Item until SV-IP B2 appears on the display. e Press Value until 213 appears on the display. f Press Enter/Cancel. g Press Item until SV-IP B3 appears on the display. h Press Value until 211 appears on the display. i Press Enter/Cancel. j Press Item until SV-IP B4 appears on the display. k Press Value until 12 appears on the display. l Press Enter/Cancel.
Reset printer and the firmware will be upgraded.
Notes: After the Completed. Network Card will start about 30secs
later message is displayed on SyncThru, click OK. It may take a few seconds to write the new file to Firmware. Normally 30 seconds is sufficient.
This chapter will help you understand what kind of paper you can use with the ML-7300 series printer and how to properly load paper in the different paper trays for the best print quality. Topics included in this chapter are: x Loading Paper - Using the Multi-Purpose Tray - Using the Manual Feed. - Letterhead/Prepunched Paper - Envelopes - Label - Transparencies

Loading Paper

Using the Multi-Purpose Tray
Multi-Purpose tray provides a convenient way to print envelopes, transparencies, or other type of media without having to unload the other tray.
To load paper in the Multi-Purpose tray, proceed as follows.
Pull the Multi-Purpose tray towards you.
Slide the length guide out toward you.

P RINT M EDIA

Flex the sheets back and forth to loosen them, then fan them.
Notes: Do not fold or crease the paper. Place the paper with the recommended print side face up.
Place the paper against the side of the Multi-Purpose tray with the recommended print side face up and the top edge going in first toward the printer as shown.
Adjust the paper guide to the size of the paper inserted by pushing the guide.

4.2 P RINT M EDIA

Using the Manual Feed
The Manual Feed feature allows you to print from the Multi-Purpose tray onto special media such as envelopes or letterhead. If the Tray menu item is set to Manual, the printer will print only from the Multi-Purpose tray. Manual Feed can be selected through the software or printer driver too.
1 Select Manual as the paper source.
Set the source item in the properties dialogue box to Manual. You can select Manual as the paper source by setting the Tray item using the operator panel menu.
2 Print your document. 3 Place a sheet of paper in the

Multi-Purpose tray.

4 Press continue key when you are

prompted.

Letterhead / Prepunched Paper
Special paper includes letterhead, prepunched, envelopes, labels, and transparencies. When printing letterhead and prepunched paper, it is important to load the trays with the correct orientation.

For Multi-Purpose tray,

Load the paper with the side-to-beprinted facing up, and the top, short edge toward the printer. Set the source item in the properties dialogue box to Manual or MP.
- To print continuously from Multi-Purpose tray, set the source item to MP. - To print a sheet of paper from Multi-Purpose tray, set the source item to Manual.

Paper Tab

You can restore all the original settings of the PCL 6 printer driver by clicking Defaults.

5.2 P RINTING TASKS

Copies Use the Copies box to set the number of copies you want to print.
Paper Orientation Choose Portrait or Landscape to select the default orientation of the printed page.

printable area

Different Soruce for First Page If the box is checked, this feature is enabled and the dialog box allows you to select the desired paper source for the First Page and Other Pages independently. If the box is empty, this feature is disabled.
Notes: The paper size for all pages of the print job

must be the same.

Paper Source The source setting identifies the default paper tray. Paper sizes Use this setting to select the paper size. Paper type The Paper type setting lets you specify the type of print material installed in each tray.
Important If you want to know more about each menu, click on the Help button.
The help screen gives detailed information about each menu.

Graphic Tab

The settings on the Graphic tab allow you to fine tune your image quality and to balance print quality and print speed.

5.4 P RINTING TASKS

Resolution Select from the available setting to set the maximum resolution for your print jobs.
SRT Mode Some printed characters or images can appear to have jagged or uneven edges. Set this Samsung Resolution enhancement Technology (SRT) option to improve the print quality of your text and image and to make the characters and images appear smoother.
Notes: SRT Mode is disabled when 1200 dpi settings are

selected.

Toner Save Mode This determines the amount of toner to be used while printing a page. The printer uses 50% less toner when Toner Save Mode is selected.
Graphic Mode This setting allows you to change the Graphic Mode.
Halftoning This setting lets you fine-tune the way colors in graphic images are converted to gray dot patterns.

Output Tab

4 pages per sheet

6 pages per sheet

5.16 P RINTING TASKS

2 Click the Output tab, and choose Multiple Pages per
Side in the Type drop-down list. Then select the number of pages you want to print per sheet (1, 2, 4, 6, 9 or 16) in the Pages per Sheet drop-down list.
3 Click Print Page Borders if you want to print a border
around each page on the sheet. Print Page Borders is enabled only if Pages per Sheet is 2, 4, 6, 9, or 16.
4 Click OK, then start printing.

Printing Booklets

Booklet printing feature allows you to print your document as a 2-sided (duplex) job and arrange the pages so that the paper can be folded in half after printing to produce a booklet.

Portrait orientation

Landscape orientation
Notes: For booklet printing, only four paper sizes are supported: Letter, A4, Legal, and Executive.
2 Click the Output tab, then choose Booklet Printing from
the Type drop-down list. When you select Booklet Printing, the Duplex option automatically changes to Short Edge. This setting is required to format the printed pages correctly.

8-page document

3 Print the document. 4 Fold and staple the pages.
Printing on Different Paper for the First Page
application, access the printer properties. See page 5.1 to access the printer properties.
2 Click the Paper tab, and click Different Source for First
Page. If the box is checked, this feature is enabled and the dialog box allows you to select the desired paper source for the First Page and Other Pages independently. If the box is empty, this feature is disabled.
3 Click OK, then start printing.
Notes: The paper size for all pages of the print job must

be the same.

5.18 P RINTING TASKS
Fitting Your Document To a Selected Paper Size
This printer feature allows you to scale your print job to any selected paper size regardless of the digital document size. This can be useful when you want to check fine details on a small document.
2 Click the Output tab, and select Fit to Page in the Type

steady and meets printer specifications.
The printer does not operate by pressing the button on the operator panel.
Turn the printer off, and then turn the

printer on.

It cannot print from software applications.
1 Select START Settings Printers from
Windows task bar (See page 5.1).
2 Click on the PCL 6 or PS printer icon. 3 Select File Default Printer.
The printed data is not sent to the printer. The test page is not printed.
Check the printer cable connections (See page 2.8). Check the printer port on your computer. Check that all trays are properly loaded,
adjusted, and installed in the printer.
Check that all covers are correctly closed.

7.8 P ROBLEM S OLVING

Poor Print Quality
The vertical lines are printed on the page. Print is too light.
Distribute the toner in toner cartridge (See page 6.1). Adjust the Density menu item setting (See page 3.12). Clean the inside of the printer (See page 6.4).
There are toner speckles.
Print a few more pages to see if the problem will correct itself. Clean the inside of the printer (See page 6.4). Check the paper type and quality.
The printer drops letters.
Check the paper type and quality. Check the printers environment. Install a new toner cartridge. Check the printer cable connections.
Dirty spots on the back side of paper of fuser assy contamination.
Heavy printing may lead to toner accumulationg on the pressure foller of the fuser assembly. The accumulated toner may melt and transfer onto the back side of the paper. Select FUSER CLEAN in the JOB MENU. Selecting FUSER CLEAN will rotate the motor
for about 10 seconds and print one page of a specified pattern for fuser cleaning and then stop.

PS(PostScript) Problems

The Error messages (This job contains binary data.) are printed.
Open the Properties of PS driver. Click on PostScript. Click on the Advanced button. The pure binary data is not supported. Choose the others.
The Optional Tray2 is not selected in PS driver.
1 Open the PS driver Properties. 2 Set Optional Tray 2 item of Device Option to

installed.

Network Problems
You cannot see any of DHCP server, BOOTP server or RARP server, when you want to set IP address to print server.

There are two methods.

On the printer front panel, you can set IP
address in Network Menu. You can find the following menu. NETWORK MENU CFG NET TCP/IP CFG TCP CFG ADRS

7.10 P ROBLEM S OLVING

Macintosh Problems
The printer driver icon does not appear in the Chooser dialogue box.
LaserWriter 8.x driver should be installed in Mac OS. Check that it is in the Extensions folder under the System folder. If not, install LaserWriter 8.x driver. Make sure that you use the standard cable. Make sure that the printer is connected to the proper network. Check AppleTalk in the Control Panel on the Apple menu.

graphic mode.5.5 graphic tab.5.4
halftone, setting.5.5 hardware requirements.2.13

I NDEX

infrared adapter.F.15 I/O MENU.3.17
network interface install network card.F.8 set up a locally shared printerD.1 network menu.3.18 network problem.7.10

JOB MENU.3.12

option closing cover.F.3 memory SIMM.F.5 nwtwork option card.F.8 Optional Tray 2.F.17 preparations.F.2 serial/IrDA.F.15 serial/LocalTalk.F.14 orientation.5.3 overlay tab.5.9
Label, printing.4.7 Landscape.5.3 Linux.G.1 LocalTalk.F.12 LSU cleaner.6.6
Macintosh.B.1 Macintosh Problems.7.11 manual feed loading paper.4.3 paper source setting.5.3 memory, option.F.5 menu botton.3.2 MP size.3.5 multiple images.5.7 multi-purpose tray loading paper.4.1 paper soruce setting.5.3
paper acceptable size and capacities A.4 guidelines.A.5 specifications.A.4 supported type.A.5 paper orientation, setting.5.3 paper source, setting.5.3 paper tray change paper size in tray.5.3 load paper.2.5 optional tray 2.F.17

(continued)

rear paper guide.2.5 rear right guide.2.6 rear view.1.3 REDAY status message.3.3 resolution.5.5 ROM SIMM connector.F.4
paper type, setting.5.3 parallel, connection.2.8 PCL 6, Properties graphic tab.5.4 output tab.5.6 overlay tab.5.9 paper tab.5.2 printer tab.5.8 watermark tab.5.11 postscript emulation.C.2 install PPD file for Macintosh.B.1 power saver.3.9 power switch.2.10 print quality problem, solving.7.9 printer control board.F.4 printer driver.2.12 pcl 6 postscript.C.1 font navigator.2.16 linux driver.G.1 printer memory connector.F.4 printer menu.3.4 printer tab.5.8 printing menu.3.5 printing problem.7.8 PS3 menu.3.17
SELFTEST.2.11 Serial/LocalTalk connector.F.4 Serial/LocalTalk option card.F.12 setting up.2.12 software requirements.2.13 specifications paper.A.4 controller.A.1 enginge.A.2 paper handling.A.3 environment.A.3 package weight.A.3 SRT mode.5.5

quality, problems.7.9

III I NDEX
test menu.3.15 testing the printer.2.11 toner cartridge distributing.6.1 install.2.3 life expectancy.6.1 recycle.6.1 redistribute toner.6.2 save toner.5.5 storage.6.1 top cover.1.3 top output bin.1.3 transparencies.4.8

value button.3.1

watermark tab.5.11 width guide.2.5
uninstall utility.2.15 unpacking your printer.2.1