SAMTRON 73V/93V

Select Model Name

SAMTRON 93V
Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment.

Prohibited

Important to read and understand at all times

Do not disassemble

Disconnect the plug from the outlet

Do not touch

Grounding to prevent an electric shock
When not used for extended periods of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. This may cause an electric shock or fire.
Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause an electric shock or fire.
Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage.
Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage. Failure to do so may cause an electric shock or fire.
Do not connect too many extension cords or plugs to an outlet. This may cause a fire.
Installation Put your monitor in a location with low humidity and a minimum of dust. An electric shock or fire could result inside the monitor.
Do not drop the monitor when moving it. This may cause damage to the product or human body.
Place the monitor on a flat and stable surface. The monitor can cause injury by falling.
Set down the monitor carefully. It could be damaged or broken.
Do not place the monitor face down. The TFT-LCD surface may be damaged.
Installing a wall bracket must be done by a qualified professional. Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual.
Leave a space for ventilation between the product and the wall. Poor ventilation may cause the interior temperature to rise and lead to a fire.
When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric.
Do not spray water or detergent directly on the monitor. This may cause damage, electric shock or a fire.
Use the recommended detergent with a smooth cloth.
If the connector between the plug and the pin is dusty or dirty, clean it properly with a dry cloth. A dirty connector can cause an electric shock or fire.
Contact a Service Center or Customer Center for interior cleaning once a year. Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or a fire.
Other Do not remove cover (or back). No user serviceable parts inside. This may cause an electric shock or a fire. Refer servicing to qualified service personnel.
If your monitor does not operate normally - in particular, if there are any unusual sounds or smells coming from it - unplug it immediately and contact an authorized dealer or service. This may cause an electric shock or fire.
Be careful not to let water drip into the monitor or expose the monitor to moisture. This may cause malfunction, an electric shock or a fire. Especially avoid operating the monitor near water or outdoors where it could be exposed to snow or rain.
If the monitor is dropped or the casing is damaged, turn the monitor off and unplug the power cord. The monitor may malfunction, causing an electric shock or a fire. Then contact the Service Center.
Keep the power off when there is thunder and lightening outside, or let the monitor remain unused for an extended period of time. The monitor may malfunction, causing an electric shock or a fire.
Do not try to move the monitor by pulling on the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.

Do not move the monitor right or left by pulling only the wire or the signal cable. This may cause a breakdown, electric shock or a fire due to damage to the cable.
Do not cover the vents on the monitor cabinet. Bad ventilation may cause a breakdown or fire.
Do not place water containers, chemical products or small metal objects on the monitor. This may cause malfunction, an electric shock or a fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center. Do not use or store inflammable substances near the monitor. This may cause an explosion or fire.
Never insert anything metallic into the monitor openings. This may cause an electric shock, fire or injury.
Do not insert metal objects such as utensils, wire or drill bits, or things that
catch fire easily, such as pieces of paper or matches, into the vents or the headphone or A/V ports on the monitor. This may cause malfunction, an electric shock or a fire. Always contact the Service Center if foreign substances/objects enter into the monitor.
If you view a fixed screen for an extended period of time, residual image or blurriness may appear. Change the mode to energy save or set a screensaver to moving picture when you need to be away from the monitor for an extended period of time.
Adjust the resolution and frequency to the levels appropriate for the model. Inappropriate resolution may cause undesirable picture quality. 19 inch - 1280 X 1024
Keep a proper distance between your eyes and the monitor screen. Sitting too close to the monitor on a continuous basis may damage eyesight.
To ease eye strain, take at least a five-minute break after every hour of using the monitor.
Do not use the monitor where it can be exposed to strong vibrations. Exposure to strong vibrations can be a fire hazard and shorten the life of the monitor.
When moving the monitor, turn the power switch off and unplug the power cord. Make sure that all cables, including the antenna cable and cables connecting to other devices, are disconnected before moving the monitor. Failure to disconnect a cable may damage it and lead to a fire or an electric shock.
Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.

Unpacking

Monitor

Bottom

Hanger

Manual

Quick Setup Guide

Warranty Card

User's Guide, Monitor Dirver CD

D-Sub Cable

Power Cord
Menu button [ ] MagicBright button [ ]
Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons. 1) Text : Normal Brightness For documentations or works involving heavy text. 2) Internet : Medium Brightness For working with a mixture of images such as text and graphics. 3) Entertain : High Brightness For watching motion pictures such as a DVD or VCD. 4) Custom Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu.

Brightness button [ ] ]

When OSD is not on the screen, Push the button to adjust brightness. Use this button for navigate and select menus or adjust the menu items in the menu screen. Activate a highlighted menu item. / Use this button for auto adjustment direct access. Use this button for turn the monitor on and off.
2,3. Adjust buttons [ 4. 5. Enter button [ ]/ Auto button Power button [ ]

Power indicator

This light glows green during normal operation, and blinks green once as the monitor saves your adjustments.
See PowerSaver described in the manual for further information regarding power saving functions. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
(The configuration at the back of the monitor may vary from product to product.) 1. 2. Power port D-sub 15-pin port Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.
See Connecting Your Monitor for further information regarding cable connections.
Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. MagicBright is a new feature providing optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Text, Internet, and Entertain. Each mode has its own pre-configured brightness value. You can easily select one of four settings by simply pressing MagicBright control buttons. 1) Text : Normal Brightness For documentations or works involving heavy text. 2) Internet : Medium Brightness For working with a mixture of images such as text and graphics. 3) Entertain : High Brightness For watching motion pictures such as a DVD or VCD. 4) Custom Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. >>Click here to see an animation clip

Power button [ ] / Power indicator
Use this button for turn the monitor on and off./ This light glows green during normal operation, and blinks green once as
the monitor saves your adjustments. 4. Brightness button [ ] ] When OSD is not on the screen, Push the button to adjust brightness. Adjust items in the menu. Activate a highlighted menu item. / Use this button for auto adjustment direct access.
2,4. Adjust buttons [ 5. Enter button [ ]/ Auto button
(The configuration at the back of the monitor may vary from product to product.)
Power port D-sub 15-pin port
Connect the power cord for your monitor to the power port on the back of the monitor. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

1. 2-1.

Connect the power cord for your monitor to the power port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, D-sub connector on the back of your monitor.

2-2. 2-3. 3.

Connected to a Macintosh. Connect the monitor to the Macintosh computer using the D-SUB connection cable. In the case of an old model Macintosh, you need to connect the monitor using a special Mac adaptor. Turn on your computer and monitor. If your monitor displays an image, installation is complete.

Monitor Assembly

1. Monitor and Bottom 2. Monitor and Hanger Attaching a base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.
A.Monitor B.Mounting interface pad 1. 2. 3. 4. Turn off your monitor and unplug its power cord. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. Remove the four screws and then remove the Stand from the LCD monitor. Align the Mounting Interface Pad with the holes in the Rear Cover Mounting Pad and secure it with the four screws that came with the arm-type base, wall mount hanger or other base.
When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions as appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. Internet web site : http://www.samsung-monitor.com/ (Worldwide) http://www.samsungusa.com/monitor (USA) http://www.sec.co.kr/monitor (Korea) http://www.samsungmonitor.com.cn/ (China)
Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button.

5. 6. 7. 8. 9. 10.

Linux Operating System To execute X-Window, you need to make the X86Config file, which is a type of system setting file. Press Enter at the first and the second screen after executing the X86Config file. The third screen is for setting your mouse. Set a mouse for your computer. The next screen is for selecting a keyboard. Set a Keyboard for your computer. The next screen is for setting your monitor. First of all, set a horizontal frequency for your monitor. (You can enter the frequency directly.) Set a vertical frequency for your monitor. (You can enter the frequency directly.) Enter the model name of your monitor. This information will not affect the actual execution of XWindow. 10. You have finished setting up your monitor. Execute X-Window after setting other requested hardware. 1. 2. 3. 4. 5. 6. 7. 8. 9.
Attaching a base This monitor accepts a 100 mm x 100 mm VESA-compliant mounting interface pad.

Windows XP/2000

1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button.
4. If you can see following "Message" window, then click the "Continue Anyway" button. Then
click "OK" button.
Windows XP | Windows 2000 | Windows NT | Linux
Microsoft Windows XP Operating System
10. Monitor driver installation is completed.
Microsoft Windows 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps.
1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon. Choose the "Settings" tab and then click "Advanced.". Choose "Monitor". Case1: If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2: If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click on "Update Driver." then click on the "Next" button. Choose "Display a list of the known drivers for this device so that I can choose a specific driver" then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver). Click the "Open" button, then click "OK" button. Choose your monitor model and click the "Next" button then click "Next" button. Click the "Finish" button then the "Close" button. If you can see the "Digital Signature Not Found" window then click the "Yes"button. And click the "Finish" button then the "Close" button.

Microsoft Windows NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test. If the screen is not normal, change to a different mode (lower mode of resolution, colors or frequency). If there is no Mode at All Display Modes, select the level of resolution and vertical frequency by referring to the Preset Display Modes in the user guide.
1. Opens the OSD menu. Also used to exit the OSD menu or return to the previous menu. 2. These buttons allow you to adjust items in the menu. 3. These buttons allow you to adjust items in the menu. 4. Activate a highlighted menu item.
Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.

MagicBright

Menu MagicBright
Description Then push the MagicBright button again to circle through available preconfigured modes.
- four different mode (Custom/Text/Internet/Entertain)

Brightness

Menu Brightness Adjust Brightness.

Description

Picture

Menu Brightness

Description Adjust the Brightness. Direct Access Feature : When OSD is not on the screen, Push the button to adjust brightness. Adjust the Contrast.

Play/Stop

Contrast
Menu Color Tone Color Control Gamma
Description The tone of the color can be changed and one of four modes can be selected - Cool, normal, Warm and Custom. Follow these steps to adjust individual R,G,B color balance. Select one of three pre-defined gammas.

Menu Coarse

Description Removes noise such as vertical stripes. Coarse adjustment may move the screen image area. You may relocate it to the center using the Horizontal Control menu. Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Follow these instuction to change the clearance of image. Follow these instructions to change the horizontal position of the monitor's entire display. Follow these instructions to change the vertical position of the monitor's entire display.

Sharpness H-Position V-Position
Description Follow these steps to change the language used in the menu. You can choose one of seven languages. (English, German, Spanish, French, Italian, Swedish, Russian) Note:The language chosen affects only the language of the OSD. It has no effect on any software running on the computer. You can change the horizontal position where the OSD menu appears on your monitor. You can change the vertical position where the OSD menu appears on your monitor. Change the translucency of the background of the OSD. The menu will automatically turn off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it turns off.

Language

H-Position V-Positon Transparency

Display Time

Menu Image Reset Color Reset
Description Image parameters are replaced with the factory default values. Color parameters are replaced with the factory default values.

Information

Menu Information
Description Shows a video source, display mode on the OSD screen.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call, the phone number on the Information section or contact your dealer.
Symptom No images on the screen. I cannot turn on the monitor.
Check List Is the power cord connected properly? Can you see "Check Signal Cable" on the screen? If the power is on, reboot the computer to see the initial screen(the login screen), which can be seen.
Solutions Check the power cord connection and supply. Check the signal cable connection. If the initial screen (the login screen) appears, boot the computer in the applicable mode (the safe mode for Windows ME/XP/2000) and then change the frequency of the video card. (Refer to the Preset Display Modes) Note: If the initial screen (the login screen) does not appear, contact a service center or your dealer.
Can you see "Not Optimum Mode" "Recommanded mode 1280 x 1024 60Hz" on the screen?

You can see this message when the signal from the video card exceeds the maximum resolution and frequency that the monitor can properly handle. Adjust the maximum resolution and frequency that the monitor can properly handle. If the display exceeds SXGA or 75Hz, a "Not Optimum Mode. Recommended mode 1280 x 1024 60Hz" message is displayed. If the display exceeds 85Hz, the display will work properly but the "Not Optimum Mode. Recommended mode 1280 x 1024 60Hz" message appears for one minute and then disappears. Please change to the recommended mode during this one-minute period. (The message is displayed again if the
system is rebooted.) There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. press a key on the keyboard to activate the monitor and restore the image on the screen. Check the signal cable connection.Make sure the video card is fully inserted in it's slot. Reboot the computer.
The screen shows strange colors or just black and white.
Is the screen displaying only one color as if looking at the screen through a cellophane paper? Have the screen colors become strange after running a program or due to a crash between applications? Has the video card been set properly?
Set the video card by referring to the video card manual. Adjust screen image position and size using the OSD. Adjust the resolution and frequency at the video card. (Refer to the Preset Display Modes).
The screen suddenly has become unbalanced.
Have you changed the video card or the driver? Have you adjusted the resolution or frequency to the monitor?
The screen can be unbalanced due to the cycle of the video card signals. Readjust Position by referring to the OSD. The screen is out of focus or OSD cannot be adjusted. LED is blinking but no images on the screen. Have you adjusted the resolution or frequency on the monitor? Is the frequency properly adjusted when checking the Display Timing on the menu? Adjust the resolution and frequency of the video card. (Refer to the Preset Display Modes). Adjust the frequency properly by referring to the video card manual and the Preset Display Modes. (The maximum frequency per resolution may differ from product to product.) There are only 16 colors shown on the screen. The screen colors have changed after changing the video card. There is a message that reads "Unrecognized monitor, Plug & Play (VESA DDC) monitor found". Have the Windows colors been set properly? Has the video card been set properly? Have you installed the monitor driver? See the video card manual to see if the Plug & Play (VESA DDC) function can be supported. Windows ME/2000/XP: Set the colors properly at the Control Panel Display Settings. Set the video card by referring to the video card manual. Install the monitor driver according to the Driver Installation Instructions. Install the monitor driver according to the Driver Installation Instructions.

Check the following items if there is trouble with the monitor.
1. check if the power cord and the video cables are properly connected to the computer. 2. Check if the computer beeps more than 3 times when booting. (If it does, request an after-service for the main board of the computer.) 3. If you installed a new video card or if you assembled the PC, check if the installed the adapter(video) driver and the monitor driver. 4. Check if the scanning ratio of the video screen is set at 75Hz. (Do not exceed 60Hz when using the maximum resolution.) 5. If you have problems in installing the adapter (video) driver, boot the computer in Safe Mode, remove the Display Adapter at the "Control PanelSystemDevice Administrator" and then reboot the computer to reinstall the adapter (video) driver. If problems repeatedly occur, contact an authorized service center.

Q&A

Question How can I change the frequency? Answer Frequency can be changed by reconfiguring the video card. Note that video card support can vary, depending on the version of the driver used. (Refer to the computer or the video card manual for details.) How can I adjust the resolution? Windows ME/XP/2000 : Set the resolution at the Control PanelDisplaySettings. * Contact the video card manufacturer for details. How can I set the Power Saving function? How can I clean the outer case/LCD Panel? Windows ME/XP/2000 : Set the function at BIOS-SETUP of the computer or the screen saver. (Refer to Windows/Computer Manual). Disconnect the power cord and then clean the monitor with a soft cloth, using either a cleaning solution or plain water. Do not leave any remains of the detergent nor scratch the case. Do not allow any water to go inside the monitor.

Self-Test Feature Check

Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box with a border and text inside as shown in the following illustration: The three boxes inside the border are red, green and blue.

Failure of any of the boxes to appear indicates a problem with your monitor. This box also appears during normal operation if the video cable becomes disconnected or damaged. 4. Turn off your monitor and reconnect the video cable; then turn on both your computer and the monitor. If your monitor screen remains blank after using the previous procedure, check your video controller and computer system; your monitor is functioning properly.
Warning Messages If there is something wrong with the input signal, a message appears on the screen or the screen goes blank although the power indicator LED is still on. The message may indicate that the monitor is out of scan range or that you need to check the signal cable.
Environment The location and the position of the monitor may influence the quality and other features of the monitor. 1. if there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. 2. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the computer. Therefore, if there is trouble with the computer or the video card, this can cause the monitor to become blank, have poor coloring, noise, Video mode not supported, etc. In this case, first check the source of the problem, and then contact a service center or your dealer. Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode" "Recommanded mode 1280 x 1024 60Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. In this case, check the computer for trouble.

SAMTRON 73V

General
General Model Name LCD Panel Size Display area Pixel Pitch Type Synchronization Horizontal Vertical Display Color 16,194,277 Colors Resolution Optimum resolution Maximum resolution Input Signal, Terminated RGB Analog, 0.7 Vpp positive at 75 ohms Separate H/V sync, TTL level positive or negative. Maximum Pixel Clock 140 MHz Power Supply AC 90 ~ 264 VAC, 60/50 Hz 3Hz Signal Cable 1280 x 1024@60 Hz 1280 x 1024@75 Hz 30 ~ 81 kHz 56 ~ 75 Hz 17inch Diagonal 337.92 (H) x 270.336 (V) 0.264mm (H) x 0.264mm (V) a-si TFT active matrix SAMTRON 73V
15pin-to-15pin D-sub cable, Detachable Power Consumption(maximum) Less than 34W Dimensions (WxDxH)/ Weight 382.0 x 62.0 x 320.5 mm (Without Stand) 382.0 x 175.0 x 383.7 mm (with Basic Stand)/4.55kg VESA Mounting Interface 100mm x 100mm (for use with Specialty(Arm) Mounting hardware.) Environmental considerations Operating Storage Plug and Play Capability This monitor can be installed on any Plug & Play compatible system. Interaction of the monitor and computer systems will provide the best operating conditions and monitor settings. In most cases, monitor installation will proceed automatically, unless the user wishes to select alternate settings. Dot Acceptable TFT LCD panel manufactured by using advanced semiconductor technology with precision of 99.999% above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. For example, the number of TFT LCD pixels that is contained in this product are 3,932,160. Note: Design and specifications are subject to change without prior notice. Temperature: 50F ~ 104F(10C ~ 40C) Humidity: 10% ~ 80%, non-condensing Temperature: -4F ~113F (-20C ~ 45C) Humidity: 5% ~ 95%, non-condensing

PowerSaver

This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods. The PowerSaver system operates with a VESA DPMS compliant video card installed in your computer. Use a software utility installed on your computer to set up this feature. State Power Indicator Power Consumption Normal Operation Green Less than 34W Power saving mode EPA/ENERGY 2000 Green, Blinking Less than 1W(Off-mode) Power Switch off Black Less than 1W (110/120 Vac)
This monitor is EPA ENERGY STAR compliant and ENERGY2000 compliant when used with a computer equipped with VESA DPMS functionality. As an ENERGY STAR Partner, SAMSUNG has determined that this product meets the ENERGY STAR guidelines for energy efficiency.

Preset Timing Modes

If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Display Mode IBM, 640 x 350 IBM, 640 x 480 IBM, 720 x 400 MAC, 640 x 480 MAC, 832 x 624 MAC, 1152 x 870 VESA, 640 x 480 VESA, 640 x 480 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 800 x 600 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1024 x 768 VESA, 1152 x 864 VESA, 1280 x 1024 VESA, 1280 x 1024 Horizontal Frequency (kHz) 31.469 31.469 31.469 35.000 49.726 68.681 37.500 37.861 35.156 37.879 46.875 48.077 48.363 56.476 60.023 67.500 63.981 79.976 Vertical Frequency (Hz) 70.086 59.940 70.087 66.667 74.551 75.062 75.000 72.809 56.250 60.317 75.000 72.188 60.004 70.069 75.029 75.000 60.020 75.025 Pixel Clock (MHz) 25.175 25.175 28.322 30.240 57.284 100.00 31.500 31.500 36.000 40.000 49.500 50.000 65.000 75.000 78.750 108.00 108.00 135.00 Sync Polarity (H/V) +/-/-/+ -/-/-/-/-/-/+/+ +/+ +/+ -/-/+/+ +/+ +/+ +/+

Service

SAMTRON CANADA SAMSUNG ELECTRONICS CANADA INC. 7037 FINANCIAL DRIVE MISSISSAUGA, ONTARIO L5N 6R3 TEL : 1-800-726-7864 FAX : 905-542-1199 SAMTRON EUROPE SAMSUNG ELECTRONICS GMBH SAMSUNG-HAUS, AM KRONBERGER HANG SCHWALBACH/TS., GERMANY TEL: 49 (0180) 5121213* FAX: 49 (0180) 5121214* * DM 0,24/MIN. SAMTRON MEXICO : SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V. Saturno NO.44, Col. Nueva Industrial Vallejo Gustavo A.Madero C.P.07700, Mexico D.F. Mexico TEL. 52-55-5747-5100 Fax. 52-55-02 RFC: SEM950215S98 http://www.samsung.com.mx/ IMPORTADO POR: SAMSUNG ELECTRONICS MEXICO. S.A. DE C.V. Saturno NO.44, Col. Nueva Industrial Vallejo Gustavo A.Madero C.P.07700, Mexico D.F. Mexico TEL. 52-55-5747-5100 EXPORTADO POR: Samsung Electronics CO.,LTD. 416, Mae tan-3dong, Yeongtong-gu, Suwon City, Kyoungki-Do Korea
SAMTRON SEOUL 15TH FL, JOONGANG DAILY NEWS BLDG. 7, SOONHWA-DONG,CHUNG-KU, SEOUL, KOREA, 100-759 TEL : (82-2) 727-3114 SAMTRON SWEDEN SAMSUNG ELECTRONICS SYENSKA, AB BOX 713, S- UPPLANDS VSBY TEL : 468- 590- 966- 00 FAX : 468- 590- 966- 50
SAMTRON TOKYO 17TH, HAMACHO CENTER BLDG. 2-31-1, NIHONBASHI-HAMACHO, CHOU-KU, TOKYO 103, JAPAN TEL : (81-3) 5641-9860 FAX : (81-3) 5641-9861 SAMTRON U.S.A. SAMTRON COMPUTER PRODUCTS CUSTOMER SERVICE 400 Valley Road Suite 201, Mt. Arlington, NJ 07856 TEL : 973-601-6200, FAX : 973-601-6001 1-800-SAMTRON (1-800-726-8766)
Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate. Unit: Hz
Example: If the same light repeats itself 60 times per second, this is regarded as 60 Hz.
Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle. The inverse number of the Horizontal Cycle is called Horizontal Frequency. Unit: kHz Interlace and Non-Interlace Methods Showing the horizontal lines of the screen from the top to the bottom in order is called the NonInterlace method while showing odd lines and then even lines in turn is called the Interlace method. The Non-Interlace method is used for the majority of monitors to ensure a clear image. The Interlace method is the same as that used in TVs. Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display. High resolution is good for performing multiple tasks as more image information can be shown on the screen. Example: If the resolution is 1280 x 1024 , this means the screen is composed of 1280 horizontal dots (horizontal resolution) and 1024 vertical lines (vertical resolution).